Dunlop Gripper Fast Tile Adhesive 500 ml Overview Dunlop Gripper Fast Tile Adhesive 500 ml is a high quality multipurpose adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials common building materials ceramics wood metals some plastics stone Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Apply between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time varies with product and conditions. Allow adequate time before loading or finishing. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean uncured product with a suitable solvent or water as applicable. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$32.80
Bastion High-Bond Stud Adhesive 5.2 kg is a reliable stud adhesive for fixing plasterboard to timber or metal framing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5.2 kg pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Bastion High-Bond for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Bastion High-Bond Stud Adhesive 5.2 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Plasterboard installation on studs Reducing screw count by bonding and fixing together Renovations where clean bond lines are important Suitable surfaces The adhesive works well on the following surface types when properly prepared: Timber studs Galvanised metal studs Plasterboard back surfaces Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of work within the wet time window to ensure transfer. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Applies as a bead to studs. Press board into place and fix with screws while the adhesive is wet. Final cure occurs as the solvent or moisture leaves the bead. Temperature and environmental performance Use in dry, shaded conditions during lining work. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Remove fresh smears with a suitable cleaner. Trim cured squeeze out before finishing. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Store closed and away from heat sources. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$29.39
Bostik Spray Adhesive is a clear, fast-tack, multi purpose aerosol glue designed for quick and easy bonding of lightweight materials. Ideal for craft, school, office, and general household repairs where a neat, even spray is preferred. Why you’ll love it Fast tack with strong initial grab Clear, low-mess spray pattern for even coverage Adjustable bond: reposition briefly, then press firm Non-staining on most materials Great for large areas and edge-to-edge laminations Suitable materials Paper, cardboard, photos, craft foam, felt, fabric, foil, leather, cork, many plastics, wood, and light laminates. Always test on delicate or coated surfaces. Typical uses Mounting posters, photos, and presentations Craft projects and scrapbooking Attaching fabric or felt to displays Temporary positioning before stitching or stapling How to use Ensure surfaces are clean, dry, and free of dust or oil. Shake the can well before and during use. Hold 15–20 cm from the surface and spray a light, even coat. For temporary bonds, spray one surface only and join after 10–30 seconds tack time. For stronger bonds, spray both surfaces, allow to go tacky, then press together with firm, even pressure. Drying and cure Tack time: typically 10–60 seconds depending on coat weight and conditions Handling strength: a few minutes Full bond development: 24 hours Clean up While wet, wipe overspray from hard surfaces with a suitable adhesive remover or mineral turpentine, then wash with warm soapy water. Test cleaners on an inconspicuous area first. Good to know Clear finish when dry Best at room temperature with good ventilation Not recommended for high heat, heavy structural loads, or polyethylene and polypropylene unless tested Storage and safety Store upright in a cool, dry place away from heat and flame. Use only in well ventilated areas. Avoid inhalation and contact with eyes or skin. Keep out of reach of children. Press nozzle briefly upside down after use to clear. Specifications Format: Aerosol spray Colour: Clear Size: 350 g
$35.00
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
$16.48
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
HandiTAK® is non-toxic, acid and lignin free. This reusable adhesive replaces tape, pushpins and tacks. It works on most surfaces and is great for securing pictures, keys, pens and lots of other items. Simply knead a small piece of HandiTAK® into a ball, place it between surfaces to be fastened and press firmly. Works best on: China, Crystal, Greeting Cards, Notes, Party Decorations, Posters, Straighten Pictures, Telephone, Pads Pacer Technology Super Glue’s HandiTak (HT, HT2) is a non-toxic (conforms to ASTM D-4236) reusable adhesive that replaces tape, pushpins and tacks and works on most surfaces. Properties: Appearance - yellow rubber-based mounting tape with a mild odour. (Note: contains a synthetic rubber ingredient with no natural latex). Instructions: 1. Knead a small piece of HandiTak into a ball, place it between surfaces to be fastened, and press firmly. 2. To remove HandiTak, gently roll product into a ball and lift from the surface. Use the ball to aid in removing any remaining product. SAFETY AND HANDLING PRECAUTIONS Contains rubber-based hydrocarbon mixture. Caution: HandiTak may leave some oily residue on some surfaces. If this happens, use Lighter Fluid or mineral spirits to remove residue. Do not use HandiTak on soft-flocked wallpaper, newly painted surfaces, or for hanging heavy objects such as mirrors and framed pictures. Avoid prolonged skin contact.
$8.50
Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes. Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for: • Metal • Plastics • Ceramics • Wood • Glass • Rubber • Fabrics • Brick • Leather • Canvas • Concrete • China • Vinyl • Porous materials • Non-Porous materials Properties: Initial colour: Clear Final colour: Clear to light yellow Open Time: 10 minutes Dry Time: 30 minutes Handling Time: 3 hours Full Strength: 24 hours Operating Temperature Range: -200 to 1500F (-290 to 660C) Instructions: Use in a well-ventilated area. Protect work surfaces. As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts. As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed. For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours. Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$25.00
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$7.95
SikaBond is a high strength contact adhesive that will not slump on vertical surfaces. It can be used as a one way liquid adhesive, or a two way contact adhesive, on a variety of surfaces. Uses SikaBond can be used on most substrates due to its excellent adhesion. These include: Floor and wall panels. Wood, plasterboard and chipboard. Aluminium, iron and steel. Concrete, cement sheeting and masonry. Advantages One component ready to use. Fast drying time. Easy to use. High adhesion strength. Non-slump. Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5ºC and 35ºC, this material will keep for at least twelve (12) months. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking must be removed and light sanding is recommended. Application One Way Method: This method is recommended for heavier panels or where load or stress is expected. Apply a 4 to 6mm bead of SikaBond using a cartridge gun, making sure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Two Way Method: Apply adhesive as in one way method, bring together substrates, and press firmly over entire surface to transfer adhesive. Then pull apart. Allow adhesive to tack off for 3 to 5 minutes depending on weather conditions, reposition the objects and press together firmly. The surfaces should be tapped together with a hammer and a padded block to ensure maximum contact. Maximum bond strength will be achieved in 12 to 72 hours, depending on substrates and weather. Heavy panels may require temporary mechanical fastening until maximum strength is achieved.
$5.24
Selleys Storm Waterproof Tape is a quick and easy way to seal and patch most objects*. It can be applied in the rain to stop leaks in an instant. Storm Waterproof Tape stops water leaks for 48 hours, making it ideal for emergency fixes until permanent repairs can be made. Features Waterproof & airtight seal* – Wet or Dry Stops active water leaks for up to 48 hours* Sticks to wet surfaces* Removable Suitable for interior and exterior Suitable for fresh, salt & chlorinated water Easy-to-use, DIY optimised format Where can this product be used? Can be used on gutters & flashing, down pipes, caravans, tents & tarps, rubber/plastic/vinyl pool liners, PVC piping, inflatable pool toys, small boats & kayaks air mattresses, umbrellas and more! Suitable for Aluminium, Galvanised Steel, Colorbond® Steel, Copper, Brass, Fibreglass, some rubbers and plastics* Ensure surface is free of dirt, grease and oil Cut tape or patch to desired size. Ensure there is at least 2-3cm of tape extending beyond each edge of the hole Remove backing paper, position carefully and press down firmly Once in position, rub firmly to ensure no air or water bubbles are left under the tape, and ensure good contact between the tape and substrate Leave tape until permanent repairs can be made
$25.00
Sole Grip is an easy-to-apply compound to repair and protect most shoe soles. Use it to coat the soles of shoes and protect from general wear and tear, extending the life of your shoes. Features: Easy to use Long wearing May be applied to both new and old shoe soles, as a repair or non-slip surface Appearance Dark brown tacky paste. Where can this product be used? Apply to new shoes to extend their sole life Building up worn soles of shoes to extend their life Creating an anti-slip surface on smooth soles of shoes Creating an anti-slip surface on the bottom of furniture legs and castor holders Creating an anti-slip base on fabric items such as dollies or placemats Sole Fix is not an adhesive May not adhere to some plastic/rubber soles Will not bridge gaps where no backing exists What materials is this product suitable for? Leather Rubber Synthetic Plastic How to use this product Roughen soles with the scraper provided. Clean the surface with Selleys Solvent Acetone. Do not use Turpentine or Kerosene. (Note: Slow drying solvents such as Mineral Turps may interfere with adhesion). Squeeze sufficient material for a thin layer about 1.5mm thick. Spread evenly over sole Leave for 30 minutes before further applications. If required, apply 2 or 3 layers on average soles. On worn soles apply to suit. Leave for 24 hours before wearing. Edges may be sandpapered or cut back and trimmed with a knife. Handy tips For best results, new shoes should be worn for several days before applying SoleGrip Clean up excess with Mineral Turpentine prior to cure Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Avoid skin contact and avoid breathing vapours. If eye contact occurs, flush eyes with water for 15 minutes. Obtain medical attention. If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If swallowed, DO NOT induce vomiting. Give a glass of water and seek medical advice. Intentional misuse by deliberately inhaling vapours of this product can be harmful or fatal.
$18.69
Selleys Porcelain Fix is a high strength two part white epoxy adhesive filler in a handy dual syringe. Specifically designed to fill and repair cracks, chips and breakages in porcelain, enamel and crockery. Features -High Strength – 2 part epoxy mix ensures high strength -Achieves maximum bond within 8 hours -Generous working time – Up to 10 minutes at 20°C -Can be sanded -Dries white and can be painted over -Heat resistant to 93°C -Can be used as gap filler – i.e. if join of breakage does not match up perfectly -Can be tinted Where can this product be used? -For bonding & filling: China, pottery, porcelain, ceramics, Earthenware -Repair a chipped sink -Repairing broken crockery – plates, cups, bowls etc -Fix a chip in your porcelain or enamel basin or bath -Repairing chips or replacing a broken section of your toilet -Should not be used on objects subject to high temperatures such as ovens and dishwashers. What materials is this product suitable for? China Pottery Porcelain Ceramics Earthenware Bathroom fittings How to use this product -Surfaces joined should be clean and dry. -Remove cap and pierce seal in each nozzle with the spatula/pin provided. -The dual syringe will dispense equal portions of Part ‘A’ and Part ‘B’. Mix thoroughly. -Apply to one surface, then bring together and hold using tape, weights etc. -Once cured this product is extremely difficult to remove. Any material squeezed out of joints or split is best removed before it sets using Solvent Acetone or Methyl Ethyl Ketone solvent. -Wipe nozzles after use. Pull the plunger back slightly and replace cap firmly over nozzles. Handy tips -For filling only, can be tinted with iron oxide or other dry pigments which must be mixed in very thoroughly. -Softens at high temperatures, but strength returns when cooled. -Wear protective gloves and eye protection when mixing or using. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. -Clean up excess material with Acetone immediately. Once set the product cannot be removed easily -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Safety tips -Avoid contact with skin and eyes and avoid breathing its vapours. -Wear protective gloves when mixing and using. -If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 13 11 26 or New Zealand 0800 764 766. -If swallowed DO NOT induce vomiting. Give a glass of water and seek medical advice. -If skin contact occurs, remove contaminated clothing and wash skin thoroughly. If in eyes, hold eyes open, flood with water for at least 15 minutes and see a doctor. -For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Store syringe in an upright position with nozzles uppermost, in a cool dry location, away from direct sunlight.
$30.00
Please refer to instructions on the photo of the back of the pack
$12.00
D-MASTIC is an oil-based sealant that forms a skin on exposure to air but remains soft underneath. Designed for sealing windscreens in cars, boats, trucks, and buses, and for metal lap joints in white goods, caravans, bus and truck bodies. Features Forms a surface skin, preventing transfer by touch and dirt pick-up on exposed surfaces Paintable with most alkyd and water-based paints (after the skin has formed). Easy clean-up off non-porous surfaces with mineral turpentine. Convenient to use non-slumping from vertical joints and easily extrudable. Long "open" time assists in the assembly of lap joints. Where can this product be used? Metals Paintwork Lacquered Work Machinery and Engines Sealing windscreens Metal lap joints in whitegoods and automotive bodies What materials is this product suitable for? Metal Glass Painted Surfaces Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as mineral turps. Cut nozzle supplied at an angle and to the required opening. Cut tip off cartridge, fit nozzle and insert in suitable caulking gun such as Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply D-Mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps or kerosene. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Maximum service is achieved when used within joints; it is not recommended to be used as a"skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. If sealing lap joints, apply suitable size bead of D-Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply mastic forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with a spatula dipped into mineral turps. Uncured product may be removed with mineral turps or kerosene. Cured product can be removed by cutting and scraping.
$21.55
![Selleys Butyl Mastic Rubber Caulking Compound for Vehicles [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697101495_09a144af-33d1-46e0-9c47-6910c6f2672a.jpg?v=1754711927&width=645)
Selleys Butyl Mastic is a synthetic resin, butyl rubber based mastic which forms a smooth tough skin, but remains permanently plastic underneath. It is available Off White. Features Remains permanently plastic under a smooth tough skin Versatile sealant with excellent adhesion to a variety of substrates without the necessity to prime Will not bleed into porous surfaces Non-sag in joints up to 12mm vertical joint Wide service temperature: –35° to +65°C Excellent weathering characteristics Does not corrode metals Good water resistance Life expectancy is approximately 5 years in a thick joint. It is recommended to use silicone sealant in thinner joints Easy smoothing and clean-up with mineral turps or white spirits Where can this product be used? Sealing aluminium windows to masonry. Sealing joints between pre-cast concrete panels or porcelain enamelled panels. Sealing edges of all types of wallboards or wherever a permanent waterproof seal is required. Sealing lap joints between metal applications with the inclusion of fasteners. Ideal for dust proofing cars, trucks, caravans, boats, etc. and is suitable for sealing cracks and gaps around brickwork, roofing and cladding. What materials is this product suitable for? Please contact your store to confirm avaliability, as some stores may have a limited range. The following should only be used as a guide and the installer should apply all Australian Standards, BCA/NZBC requirements, and best practices when installing. Surfaces to be sealed must be clean, dry and free from dust, grease, old mastic and flaking paint. If necessary clean with degreasing solvent such as white spirits. Cut nozzle supplied at an angle and to the required opening. Cut end off nipple on cartridge, fit nozzle and insert in suitable caulking gun such as the Selleys Light Speed caulking gun. If sealing lap joints, apply suitable size bead of Butyl Mastic to one surface through the intended fasten line. Bring surfaces together squeezing the mastic bead out on both surfaces and mechanically fix join where necessary. If sealing open joints, apply Butyl Mastic by forcing it into the joint ahead of the nozzle. This method aids in properly filling the joint and forcing mastic to wet on to the sides of the joint. If required, smooth surface with spatula dipped into mineral turps. Limitations: Not an elastomeric compound, it should not be used in joints subject to considerable dynamic movement. Should not be used where joint movement will exceed ±8%. Maximum service is achieved when used within joints; it is not recommended to be used as a "skim" coating over joints. Not recommended for use in joints required to resist static air or water pressure. Surfaces must be clean and dry. Life expectancy in joints is approximately 5 years Interior applications may have greatly extended skin over time due to the reduced presence of sunlight. Allow surface to skin before painting, i.e. approximately 24 hours after application. Butyl Mastic can be painted over using oil or water based paints after the surface has skinned.
$33.47
![Scotch 3M Mount Double Sided Squares Indoor 15lb x 48 [2.54cm x 2.54cm]](http://gluesaustralia.com.au/cdn/shop/files/051131769960N_f18dde17-9448-4437-aace-df5695c465e8.jpg?v=1754711993&width=645)
Scotch Indoor Double-Sided Mounting Squares are ideal for painted surfaces and allow you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, these permanent double-sided foam squares hold up to 15 pounds and deliver a strong bond every time because of their 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Squares. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3 squares To hold 15 lb use 45 squares Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White Specifications Size (Imperial) 0.5 in x 0.5 in, 1 in x 1 in
$8.89
Permanently joins metals, wood, plastics, ceramics, glass, vulcanized rubber, leather, fabrics, and plaster Pliobond sets fast, is Permanent Stays flexible and won't become brittle
$25.00
$6.94
Neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. LOCTITE® MR 5412 is a yellow, neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. Typical applications include bonding weather stripping, insulation, rubber and trim to wood and metal. Suitable for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding Technical Information % Solids 10 Agency Approvals / Specifications CFIA Listed Colour Yellow Fixture Time 15 min. Key Characteristics Waterproof Physical Form Liquid Specific Gravity 0.88 g/l Specific Gravity Temperature 25 °C Substrates Metal, Wood Directions for use: 1. Clean surfaces thoroughly. Use abrasives to remove any powdery mold release from new weatherstripping. 2. Apply a thin, even film to both surfaces. 3. Allow to dry tacky (3 to 4 minutes). 4. Bond the two surfaces together and apply enough pressure to produce uniform contact. 5. NOTE: The early strength of LOCTITE® MR 5412 is enough to hold most parts together. However, maximum strength is obtained after the adhesive is completely dry. Aging of the bond and exposure to moderate heat increases strength.
$16.45
A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. Features; Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Grabs immediately on contact Easy to spread Appearance: Yellowish to beige coloured opaque liquid with strong solvent odour. Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Repairing tents and outdoor equipment Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Attaching rubbers to your fridge door Repairing your wetsuit Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application. Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product: When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint. Surfaces to be bonded should be relatively smooth and/or close fitting. Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes. Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry. Handy tips: -Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. -Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces. -For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical. -For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. -Use a brush, knife or serrated scraper for application. -When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. -Keep container sealed when not in use. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips: -Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances. -Highly flammable. Do NOT use in the same area as flame, fire or spark producing apparatus or machinery. -This product should not be accessible to juveniles, because of its solvent content. Intentional misuse by deliberately inhaling vapours from this product can be harmful or fatal. -Contact with skin and eyes should be avoided and avoid breathing vapour. -If in eyes flush with plenty of water for 15 minutes and seek medical advice. -If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice. -For further information refer to the Safety Data Sheet (MSDS). Storage and re-use Store in a cool area away from ignition sources and out of direct sunlight.
$7.00
Gorilla Tape To-Go Handy 1" Roll Convenient for on-the-go repairs, Gorilla Tape To-Go's 1 inch width packs a powerful grip in a portable size. With double-thick adhesive, tough reinforced backing and rugged weather-resistant shell, it sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. This size is ideal size for backpacks, toolboxes, glove compartments for camping, boating and more. Use like any other tape Tear by hand or cut to size Apply carefully smoothing out air pockets or rolls That's it, enjoy the strength and durability of Gorilla Tape
$11.07
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607409N_5d23d9cf-9af4-4971-af36-316c7ce35662.jpg?v=1754712479&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$26.69
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607126N_cffee80a-3f6c-4f18-ab8b-4a06da2ea9e8.jpg?v=1754712484&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.60
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600127N_b3248bad-00e4-4a61-873b-21199bac68a6.jpg?v=1754712486&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$15.51
Introducing Gorilla All Weather Tape - Your Ultimate Outdoor Repair Companion! When it comes to outdoor repairs, ordinary tapes just won't cut it. That's where Gorilla All Weather Tape steps in! Engineered with unbeatable strength and a weather-resistant shell, this tape is the ultimate solution for all your outdoor repair needs. Brace yourself for the power of Gorilla All Weather Tape! This incredible tape is equipped with a permanent, low tack adhesive that bonds with tenacity. No matter the challenge, it holds strong and steadfast, making sure your repairs stand the test of time. Rain or shine, Gorilla All Weather Tape delivers exceptional performance. Its waterproof design resists drying, cracking, and peeling caused by sunlight, heat, cold, and moisture, making it ideal for extreme weather conditions. Experience the versatility of Gorilla All Weather Tape! It works effortlessly in both hot and cold temperatures, ensuring it remains your reliable partner no matter the season. Ease of use? Check! Applying Gorilla All Weather Tape is a breeze. Simply tear it by hand or cut it to size with a knife or scissors. Carefully apply the tape, smoothing out any pockets or rolls, and voilà! You're all set to enjoy the strength and durability of Gorilla Tape! For optimal results, ensure the surface is clean, free of dust, dirt, and debris. Store the tape flat on a non-delicate surface, keeping it away from direct sunlight. Technical Specs: Application Temperature: Above 4° C Service Temperature: -17° C to 93° C Indoor: Yes Outdoor: Yes Moisture Resistant: Waterproof Frequently Asked Questions: Q: Can Gorilla All Weather Tape be used instead of electrical tape? A: Gorilla All Weather Tape should NOT be used as an electrical tape. Q: Will Gorilla All Weather Tape work on plastic/vinyl/rubber? A: Yes, Gorilla All Weather Tape contains a highly concentrated rubber-based adhesive and sticks to most plastics, including polyethylene (PE) and polypropylene (PP). However, it does not work on materials with high oil or plasticizer content, such as EPDM rubber or PVC. For those materials, we recommend using an acrylic tape like Crystal Clear Gorilla Tape. Q: Is Gorilla All Weather Tape food safe? A: Gorilla All Weather Tape is not recommended for direct or indirect food contact and should not be considered food safe. When it comes to outdoor repairs, don't compromise. Choose the unmatched strength and durability of Gorilla All Weather Tape. Tackle any challenge, withstand any weather - trust Gorilla to get the job done right!
$32.60
Glue Dots® Repositionable Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for hanging lightweight items, securing rugs to hardwood and tile floors, and can be easily removed. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$8.73
Repositionable Dots™ Dot N Go® dispenser fits in the palm of your hand and can be used as a 'second set of hands' to hold small, lightweight items in place temporarily. It's perfect for quick fixes and repairs around the home. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$9.70
Advanced Strength Dots™ Dot N Go® fits in the palm of your hand and is perfect for quick fixes and repairs. With a small footprint, the Advanced Strength Dot N Go stores easily in a toolbox or drawer for easy access. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free Adhesive Size: 3/8 in. diameter Adhesive Color: Amber Quantity: 125 Adhesives
$8.95
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$7.98
Craft Glue Dots® are versatile, permanent adhesives ideal for heavier materials like wood or metal, large embellishments or thick cardstock. Glue Strength - Super-Strength Features/Benefits: Hand-held Dispenser | Easy to Use Acid Free| Photo Safe Non Toxic | Kid Friendly Specifications Adhesive Size: 3/8 in. diameter Adhesive Color: Clear Quantity: 200 Adhesives
$12.74
Bostik Multi Bond is a general purpose solvent based Nitrile Rubber Adhesive. It is nearly clear in colour and will give excellent bonds that are both chemical and temperature resistant. It is packaged in a convenient aluminium tube for ease of use. Where to Use Residential Commercial Industrial Substrates Toys Leather Goods Furniture Upholstery Jewellery Materials Leather Metals Wood Canvas PVC Plastics Features Quick bonding Easy to use Chemical and temperature resistant It has many household and industrial uses and is particularly suitable for bonding leather, metals, wood, canvas PVC and other plastics. It is widely used in the repair of toys, leather goods, furniture, upholstery, jewellery and in the handicraft making areas. This is an excellent product where quick bonding and a clear bond line is required especially in the DIY market. Instructions Surface Preparation Surfaces to be bonded must be dry, clean and free of grease. If surfaces are non-porous, smooth and glossy, roughen with glass paper (preferably) or apply solvent suck as Acetone As a two way dry stick: Apply an even film onto both substrates, leave 5-10 minutes then join together with as much as possible taking care not to trap any air. As a one way wet stick: Usually, this technique is employed when either one or both of substrates to be bonded are porous (e.g. fabrics, cardboard). Clean Up Any wet or partially wet adhesive can be removed with scraping and Bostik Solvent 9901. The dried adhesive is best removed with a scraper or by sanding. STORAGE AND SHELF LIFE A minimum of 12 months in original sealed packaging if stored under cover away from heat.
$9.95
Bostik Contact Bond is a solvent based, high solids, brush or scaper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. Where to Use Residential Commercial Substrates Brush or Scraper Furniture and allied industries for fixing plastic laminates Flexible decorative surface coverings Materials Neoprene rubbers Porous and non-porous surfaces Wood MDF Particleboard Plywood Leather Felts Cottonback PVC Metal Features n-Hexane formula Safe quick drying Heat and water resistant Good brushability Excellent adhesion to porous and non-porous surfaces Provides an extra strong and flexible bond on contact Uses Bostik Contact Bond is a solvent based, high solids, brush or scraper grade contact adhesive. It is specifically formulated to provide an extra-strong and flexible bond on contact. It resists heat and water. It also provides excellent adhesion to most natural and neoprene rubbers as well as a wide variety of porous and non-porous surfaces. It may be easily applied by brush or scraper giving a secure and lasting bond making it clean and economical to use. Bostik Contact Bond is primarily used in the furniture and allied industries for fixing plastic laminates and rigid or flexible decorative surface coverings to wood, MDF, particle board, plywood, leather, felt, cotton back PVC and metal. PRODUCT CHARACTERISTICS Colour Pale yellow Viscosity Medium syrup Composition Polychloroprene rubber/resin Coverage 5 to 6m² per litre TYPICAL PERFORMANCE DATA (approx.) Touch dry Tube: 5 to 15 minutes Can: 20 to 30 minutes Full cure 45 minutes Solids content 22% Specific gravity 0.83 Heat resistance > 150°C DIRECTIONS FOR USE Read and understand the Safety Data Sheet before using this product. SDS can be acquired by visiting www.bostik.com.au or by scanning the relevant QR code on the pack. SURFACE PREPARATION Ensure all surfaces are clean and dry and free from all loose paint, dust, grease, oil and foreign materials. APPLICATION Tube (Blister Pack) Application 1. Unscrew cap and pierce and of the tube with the reverse end of the cap 2. Apply thin, even film to both surfaces to be glued 3. Leave until touch dry (approximately 5 to 15 minutes), then bring both surfaces together accurately 4. Take care to avoid the formation of air bubbles between surfaces 5. To ensure maximum adhesion, clamp or weigh down the entire surface or apply firm hand pressure evenly 6. Replace screw cap to keep the contents of tube airtight CLEANING To clean up tools, equipment and adhesive spills use Mineral Turpentine. Use Bostik Handy Wipe towels to remove adhesive from the skin. STORAGE AND SHELF LIFE Store in a cool dry place between 5°C and 30°C and out of direct sunlight. Keep away from sources of ignition. Shelf life is 12 months from the date of manufacture when stored as directed. VOC INFORMATION 606g/litre
$14.78
Multipurpose Adhesive Bostik Blu-Tack® is a permanently plastic reusable material that can used as a removable adhesive or to model with. It has excellent moulding qualities as it resists slump, will not shrink, dry out or harden and can be used over and over again. Recommended Uses Ideal for a thousand and one uses including: Create 3D models Create fantastic murals on your window or wall Hold up posters Cards Children's paintings Certificates Party decorations Maps Messages Hold telephones, mouse mats and calculators in place Hold ornaments to shelves, photos in albums, screws to screwdrivers Holds model parts in position for painting or glueing and picture frames straight Safely store pins, keys, screws and other small objects Use in floral arrangements to keep flowers in place Clean fluff from fabric and dirt from computers, model railway tracks or remove dust from hard to get at places Use as a putty to block out breezes Materials Designed to stick to: Non-porous surfaces Vinyl Coated wallpaper Painted surfaces Glass Metal
$5.03
Multipurpose Adhesive Bostik Blu-Tack® is a permanently plastic reusable material that can used as a removable adhesive or to model with. It has excellent moulding qualities as it resists slump, will not shrink, dry out or harden and can be used over and over again. Recommended Uses Ideal for a thousand and one uses including: Create 3D models Create fantastic murals on your window or wall Hold up posters Cards Children's paintings Certificates Party decorations Maps Messages Hold telephones, mouse mats and calculators in place Hold ornaments to shelves, photos in albums, screws to screwdrivers Holds model parts in position for painting or glueing and picture frames straight Safely store pins, keys, screws and other small objects Use in floral arrangements to keep flowers in place Clean fluff from fabric and dirt from computers, model railway tracks or remove dust from hard to get at places Use as a putty to block out breezes Materials Designed to stick to: Non-porous surfaces Vinyl Coated wallpaper Painted surfaces Glass Metal
$6.00
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
$22.74
$15.19
$22.02
$14.32
$21.22
$12.61
$8.13
$8.79
$8.98
$6.57
$12.69
Bear masking tape is made from quality crepe paper with a natural rubber adhesive to provide instant attachment to a wide variety of surfaces. With excellent holding power, this general purpose masking tape is ideal for wrapping, bundling and sealing and removes cleanly within 24 hours of application. Resists lifting and curling Easy to tear by hand All purpose applications Removes clean within 24 hours
$7.00
You have seen 96 out of 97 products
Flexible, high-tack adhesives (often contact or PSA) for foam, fabrics, rubber and mounting tasks. Offer quick grab and good peel strength; temperature and solvent resistance vary. Great for temporary or semi-permanent bonds depending on grade. Use filters to refine by open time, removability and clean-up. Always check the product page and TDS/SDS.
