In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Water-based interior wood filler suitable for all timber types and timber by-products. Once set, the wood filler can be sanded, screwed, and nailed. The wood filler is suitable for filling cracks, holes, end grain, and edges.
For exterior use, protect with a suitable exterior grade finish (e.g. paint or stain)
Features & Benefits
Environmentally friendly
Dries quickly
Water clean up
Easy to use
Long shelf-life; if filler hardens just add drops of water & mix
Multi-purpose, 4 in 1 uses – fills nails holes, takes stain or paint easily, repairs gouges & chips and crack & edge filler
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water.
Features
No mixing required – Ready to use straight from the pack
Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear.
Non-toxic
Dries Clear
Cleans up with water
Where can this product be used?
School projects and craft
Furniture repairs
Repair a split trim
Fix a broken photo frame
Restoring furniture
Fix a wobbly chair
Gluing cupboard shelves for additional support
Repairing a door frame or window
Fix a wine rack
Re-attach book cover/spine or repair torn bindings
Fix a broken drawer
Wooden toy repairs
Craft projects
Unsuitable for use on coated wallpaper overlaps eg vinyl
Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond).
Will not take common timber stains
Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue.
Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable.
Will not bond MDF, we recommend using Aquadhere Exterior
What materials is this product suitable for?
End grain gluing
Craftwork
Cloth
Paper
Mosaics
Leather
Other craft materials
How to use this product
Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease.
Shake bottle before use
Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours.
Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood.
Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers.
Cure slows significantly in humid, cold conditions.
Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft.
Handy tips
1L covers approx. 8m2
To fill small gaps, Aquadhere can be mixed with sawdust.
Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue.
Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods.
On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond
Cured adhesive can be resoftened by prolonged contact with hot water or steam.
Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing.
If you are gluing over a larger surface, try using a small roller to aid in application.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Aquadhere is considered a non-hazardous material.
In case of eye contact, hold eye open and flush with plenty of water for 15 minutes.
Storage and re-use
For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram.
The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time.
Features & Benefits of Timbermate
No Waste, Usable to the last drop. If tub dries out just add water to soften.
Won't Shrink, Sink, Crack or Fall Out.
Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc.
Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one.
Available in 13 Timber Tones plus Natural. Use White for top coats only.
Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc.
Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use.
Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time.
Clean hands or tools with water.
Non-Flammable, Non-Toxic, Non-Yellowing.
Solvent, Latex and Acrylic Free.
Heat Proof and Freezeproof.
Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc.
Takes nails, screws, planing, sawing, drilling and routing
Can be used on Metal, Plastic, Fibreglass and in Foundries.
100% Australian Made and Owned.
Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg.
Interior Grade.
Edgefiller
Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat.
Woodfiller/Wood Putty
Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."
You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats.
Grainfiller
Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required.
MDF
Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs.
Flooring
Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement.
Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished.
Frequently Asked Questions
Question: Is TIMBERMATE toxic, flammable or harmful?
Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable.
Question: Can TIMBERMATE be used externally?
Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler.
Question: Can TIMBERMATE be used with stains and other finishes?
Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers.
Question: Can TIMBERMATE be grainfilled?
Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc.
Question: How is the grainfiller applied?
Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry.
Question: When is the stain applied?
Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours").
Question: How are the colours matched?
Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain.
Question: How long does TIMBERMATE take to dry?
Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light.
Question: What depth or width can be filled?
Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers.
Question: Why is the tub hard some days and feels dry and soft on other days?
Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten.
Question: How is TIMBERMATE softened?
Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable.
Question: Can TIMBERMATE be used for any other purpose other than wood repair?
Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting.
Question: Can TIMBERMATE go off or does it have a shelf life?
Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate.
Question: Why are so many colours available?
Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base).
Question: What is Tint Base (Natural) putty and why?
Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour.
Question: Can TIMBERMATE be used on floors?
Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors.
Question: Can TIMBERMATE be used with French Polish and Waxes?
Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE.
Question: How is an incorrect match or badly filled hole fixed?
Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary.
Question: Is TIMBERMATE Australian owned and manufactured?
Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications.
Same formula & product you trust, just better looking!
Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable.
Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age.
It is non-toxic, non-flammable & Solvent free
3-4 times stronger than standard P.V.
High Solid content (51-53%) means more glue and it goes a lot further
Does everything a P.V.A does, plus more
Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Weldbond Universal Adhesive can be used in various applications as a glue, bonding agent, sealer or primer. It’s high solid content means that it can be easily diluted and therefore becomes a very economical alternative to traditional products used for specific applications.
Same formula & product you trust, just better looking!
Weldbond is a universal adhesive that bonds almost anything! It is non-toxic, non-flammable.
Weldbond will dry clear and flexible and is therefore ideal for use with woods and fabrics as no glue lines will show and the glue will bend with movement. It is non-staining and will not become brittle with age.
It is non-toxic, non-flammable & Solvent free
3-4 times stronger than standard P.V.
High Solid content (51-53%) means more glue and it goes a lot further
Does everything a P.V.A does, plus more
Dries to a clear, flexible bond and can be used as a sealer, bonding agent or primer.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more.
About the product
Works as a sealer, bonding agent, or primer
Completely non-toxic
Dries to a clear, flexible bond
Works on porous and non-porous surfaces
UL approved
Will not dissolve hard foam
Safe for Styrofoam
Works well with Plastics and expanded polystyrene
Frequently Asked Questions
Can I keep my weldbond bottle outside in the garage? Will it freeze?
Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use.
What is the shelf life of weldbond?
Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use.
Is weldbond non-toxic?
Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236.
Is weldbond tested on animals or created with any animal by-products?
Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ready to use, hard drying acrylic putty filler
Ideal for repairing cracked, broken or uneven surfaces
30 minute fast drying time
Includes bonus applicator
Suitable for fibrous cement, brick, plaster and wood surface repairs
available in 500gm/1.5kg
Not suitable for wet areas or where structural movement occurs
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ready to use, hard drying acrylic putty filler
Ideal for repairing cracked, broken or uneven surfaces
30 minute fast drying time
Includes bonus applicator
Suitable for fibrous cement, brick, plaster and wood surface repairs
available in 500gm/1.5kg
Not suitable for wet areas or where structural movement occurs
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-291 Tube Black: Marine-Grade, Multipurpose Polyurethane Sealant
Product Benefits
IMO Certified
Bonds to a wide variety of substrates
Good ageing and weathering resistance
Elastic and low odour
Non-corrosive, Overpaintable and Sandable
Usage
Sikaflex®-291 is a multipurpose product suitable for marine constructions. It is ideal for making elastic, vibration-resistant joint seals and can also be used for interior sealing applications.
Application Information
Surface preparation is key. Surfaces must be clean, dry and free from grease, oil, and dust. Further application tips can be found in the Sika Pre-treatment Chart for Marine Applications.
Additional Details
Application Temperature: 5 ? 40 °C
Skin Time: 60 minutes
Shore A Hardness: 40
Shelf Life: 12 months when stored below 25°C
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Packaging 500 ml plastic tube
5 l and 10 l plastic pail
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application.
Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Wallboard
Wood
Masonry
Plaster
Primed nail heads
Plasterboard
Colours White
Technology Water Based
Use Interior
Exterior (when painted)
How To Use
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications).
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Handy Tips
Painting with oil-based paints is not recommended until 24 hours after filler has been applied.
Water based paints may be used immediately after filler has set.
If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping or sanding.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler.
Features
Suitable for interior and exterior applications
Good adhesions to most surfaces
Water and weather resistant
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs
What materials is this product suitable for?
Mortar
Masonry
Concrete
Wood
Stone
Primed metal surfaces
Brick
Plaster
Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next.
Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications).
Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints.
Limitations:
Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps.
Avoid using below 5°C or in wet conditions.
Painting with oil-based paints is not recommended until 24 hours after the filler has been applied.
Water-based paints may be used immediately after the filler has set.
If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material.
Features
Will not sag, run or drip.
Easy to use – no mess.
Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing.
Good adhesive strength.
Can be used to reshape, rebuild and repair a multitude of surfaces and applications.
Good gap filling properties.
Long-lasting, durable solution.
Heat resistant to 120°C continuously or 140°C intermittently.
Can be used under water (but dry surfaces for application are best and recommended).
Rapid Set (less than 10 minutes).
Can be used for fuel resistant repairs.
Appearance
Dries Dark Grey/Charcoal
Where can this product be used?
Rebuilding engine parts and rusted metal etc
Repairing a hole in a fuel tank
Repair of iron pipes, tools and equipment
Repair stripped threads
Forming of nuts and bolts in place
Attaching fixtures and signs
Fixing radiators
Repairing holes in cars and boats
Patching ducts and tanks
Making prototypes
Thread locking
Repair of down pipes and gutters
Anchoring of bolts
Repairing your metal outdoor furniture
Set time increases at temperatures below 20°C
Not recommended for plastic fuel tanks
Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber
Not tested for drinking water contact to AS/NZ 4020:2005
What materials is this product suitable for?
Steel
Wide range of terrous metal and aluminium items
Most plastics (pre-test required)
Glass
How to use this product
Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning
Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place.
For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins.
Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond.
After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted.
Wash hands thoroughly with soap and water after use.
Handy tips
Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it.
To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done.
Store in a cool place for maximum shelf life
Use Knead-It Multi Purpous for applications in contact with drinking water.
Use Knead-It Aqua for applications in wet/submerged areas.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis.
If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt.
Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal.
Storage and re-use
Replace siliver disc to seal ends and keep in a cool dry place.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water.
Features
Will not sag, run or drip
Easy to use – no mess
Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing
Good adhesive strength
Can be used to reshape, rebuild and repair a multitude of surfaces and applications
Good gap filling properties
Long-lasting, durable solution
Heat resistant to 120°C continuously or 140°C intermittently
Can be used underwater. (but dry surfaces for application are best and recommended)
Rapid set time (<10 minutes)
Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649
Excellent anchoring properties
Where can this product be used?
Repair and replacement – timber, metal, masonry, many plastics, ceramics
Mending – toys, appliances, lawn mowers, sports equipment etc
Sealing – leaks in gutters and downpipes
Patching – chipped concrete, floors, bricks, blocks etc
Attaching – fixtures, machine tags, signs etc
Anchoring – bolts, screws, housings etc
Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics
Moulding to rebuild – wrought iron fencing
Forming knobs and missing parts
Balancing – table legs etc
Fixing a damaged roof tile
Repairing a water (drinking) tank
Lost the head off your hammer? Make a new one with knead it
Replace chip in golf club (woods)
Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible
Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber
Pot life (working life) decreases above 20°C
Set time increases at temperatures below 20°C
Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm
What materials is this product suitable for?
Wood/Timber
Concrete
Anchoring bolts
Metal
Masonry
Plastics
Ceramics
How to use this product
Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning.
Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature.
Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required.
For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins.
Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond.
After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted.
Wash hands thoroughly with soap and water before product hardens.
Handy tips
Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it.
To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done.
Use Knead-It Aqua for applications in wet/ submerged areas.
Use Knead-It Steel for applications on metal or fuel contact
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup
Safety tips
Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis.
If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt.
Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal.
Storage and re-use
Replace silver disc to seal ends and keep in a cool dry place.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material.
Features
Will not sag, run or drip.
Easy to use – no mess.
Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing.
Good adhesive strength.
Can be used to reshape, rebuild and repair a multitude of surfaces and applications.
Good gap filling properties.
Long-lasting, durable solution.
Heat resistant to 120°C continuously or 140°C intermittently.
Can be used under fresh or salt water.
Longer set time (less than 20 min).
Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649.
Higher tack for underwater repairs.
Where can this product be used?
Creating water features/ attaching pebbles under water in a pond
Sealing holes in foundations and outer walls
Repairing generators, water and fuel pumps
Re-setting ceramic tiles in swimming pools etc
For fast and permanent repairs to damp and wet substrates, and even for underwater repairs
Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls
Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets
Forming custom gaskets etc
Ideal for emergency in-water repairs
Repairing fishtanks, ponds, pools
Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm
Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible.
Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber
Set time increases at temperatures below 20°C
Not recommended for use where hydrostatic pressure is present prior to cure
What materials is this product suitable for?
Fibreglass
Wood/Timber
Ceramics
Metal
Concrete
Glass
Most plastics (pre-test required)
Masonry
How to use this product
Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning.
Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature.
Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place.
For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins.
Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures.
After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted.
Wash hands thoroughly with soap and water after use.
Handy tips
Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it.
To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done.
For best results, use Knead-It Multi-Purpose for applications in contact with drinking water.
Use Knead-It Steel for applications on metal or fuel contact
Store in a cool place for maximum shelf life
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis.
If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt.
Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal.
Storage and re-use
Replace siliver disc to seal ends and keep in a cool dry place.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material.
Features
Will not sag, run or drip.
Easy to use – no mess.
Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing.
Good adhesive strength.
Can be used to reshape, rebuild and repair a multitude of surfaces and applications.
Good gap filling properties.
Long-lasting, durable solution.
Heat resistant to 120°C continuously or 140°C intermittently.
Can be used under fresh or salt water.
Longer set time (less than 20 min).
Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649.
Higher tack for underwater repairs.
Where can this product be used?
Creating water features/ attaching pebbles under water in a pond
Sealing holes in foundations and outer walls
Repairing generators, water and fuel pumps
Re-setting ceramic tiles in swimming pools etc
For fast and permanent repairs to damp and wet substrates, and even for underwater repairs
Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls
Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets
Forming custom gaskets etc
Ideal for emergency in-water repairs
Repairing fishtanks, ponds, pools
Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm
Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible.
Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber
Set time increases at temperatures below 20°C
Not recommended for use where hydrostatic pressure is present prior to cure
What materials is this product suitable for?
Fibreglass
Wood/Timber
Ceramics
Metal
Concrete
Glass
Most plastics (pre-test required)
Masonry
How to use this product
Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning.
Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature.
Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place.
For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins.
Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures.
After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted.
Wash hands thoroughly with soap and water after use.
Handy tips
Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it.
To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done.
For best results, use Knead-It Multi-Purpose for applications in contact with drinking water.
Use Knead-It Steel for applications on metal or fuel contact
Store in a cool place for maximum shelf life
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis.
If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt.
Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal.
Storage and re-use
Replace siliver disc to seal ends and keep in a cool dry place.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SANDING BLOCKS offer optimal sanding results on flat, contoured and irregular shapes.
• Flexible, to conform to contours and irregular shaped objects.
• For sanding and cleaning metal, wood, plaster, plastic, fibreglass etc.
• Can be used for wet or dry sanding.
• Rinse with water to clean.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Eazy Tape Plasterboard Joint Tape, your ultimate solution for achieving flawless walls and durable repairs. Designed for both the DIY enthusiast and the professional, this self-adhesive fibreglass mesh tape is engineered to simplify your plasterboard wall panel joining or patching tasks. Crafted from high-strength fibreglass mesh, it ensures a robust bond that complements both plaster filler and jointing compounds seamlessly.
Why choose Eazy Tape? Here are the benefits:
Easy to Use: With its self-adhesive backing, the application is straightforward and mess-free, adhering securely to surfaces without the need for additional glues.
DIY-Friendly, Professional Results: Whether you're tackling a home project or a professional job, Eazy Tape guarantees a smooth, professional finish.
Strong Bonding & Holding Power: The superior fibreglass mesh material provides exceptional strength, reducing the risk of cracks and ensuring longevity.
Quick Results: Speed up your repair or construction projects with a tape that sets quickly, allowing you to move on to the next step without delay.
Perfect for a wide range of applications, from repairing cracks to joining new wall panels, Eazy Tape Plasterboard Joint Tape is the dependable choice for achieving seamless results with ease.
Fillers and repair compounds that sand smooth for paint-ready results. Choose fast-set for quick turnarounds or extended open time for shaping. Use filters to refine by chemistry and set speed. Always check the product page and TDS/SDS.
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9314261009148.png?v=1754723592&width=645)
![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](http://gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Cedar]](//gluesaustralia.com.au/cdn/shop/files/9314261009148.png?v=1754723592&width=645)
![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](//gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](//gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](//gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](//gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
