In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Eazy Tape Plasterboard Joint Tape, your ultimate solution for achieving flawless walls and durable repairs. Designed for both the DIY enthusiast and the professional, this self-adhesive fibreglass mesh tape is engineered to simplify your plasterboard wall panel joining or patching tasks. Crafted from high-strength fibreglass mesh, it ensures a robust bond that complements both plaster filler and jointing compounds seamlessly.
Why choose Eazy Tape? Here are the benefits:
Easy to Use: With its self-adhesive backing, the application is straightforward and mess-free, adhering securely to surfaces without the need for additional glues.
DIY-Friendly, Professional Results: Whether you're tackling a home project or a professional job, Eazy Tape guarantees a smooth, professional finish.
Strong Bonding & Holding Power: The superior fibreglass mesh material provides exceptional strength, reducing the risk of cracks and ensuring longevity.
Quick Results: Speed up your repair or construction projects with a tape that sets quickly, allowing you to move on to the next step without delay.
Perfect for a wide range of applications, from repairing cracks to joining new wall panels, Eazy Tape Plasterboard Joint Tape is the dependable choice for achieving seamless results with ease.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ideal for filling holes, cracks, dents, chips and grain imperfections on interior timber surfaces. Can be nailed or planed.
Easy to sand, sets to a hard finish and is highly crack resistant.
Filling blade included
For use on: Timber (INTERIOR)
Fill depth: Up to 6mm
Dries in: 2-3 hours
Ready to use: YES
Colour: Produces a pine finish that can be tinted or stained.
Application Tips
• Surface to be filled should be clean and dry with no loose or powdery material.
• Using the attached filling blade press filler in firmly and remove excess.
* Allow drying for 2-3 hours in 2-3mm thin applications, depending on humidity. Allow longer drying if painting with solvent-based coatings (24 hours minimum) or for deeper applications.
• Sand with fine sandpaper. For a perfect finish after initial sanding back, apply a thin coat of filler, allow to dry and sand lightly with very fine (400 grit) sandpaper before staining or coating.
• When tinting or staining, the final colour is not achieved until the varnish is applied.
• Prime metals (eg, nail heads) before applying filler.
• Use Polyfilla Gap filler or silicone sealant where joint movement occurs.
• Clean up with water before filler dries
Q. I want a filler that matches the colour of the timber I am repairing. What should I use?
A. The best idea is to custom tint/stain a filler to match your timber, rather than buy a pre-tinted colour filler. This allows you the flexibility to adjust to the shade you require, rather than having the colour dictated by the manufacturer.
For interior timbers, use Polyfilla Timber Filler. If you require a wood filler that can be exposed to the elements, use Polyfilla Exterior Timber, which flexes with the natural movement of wood.
Note: When tinting /staining, the final colour is not achieved until a varnish is applied. It is worth testing first on an off-cut or inconspicuous area to see if the correct colour match is achieved.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job
Seamless Filler for Pro-Level Paint Preparations
When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 510g. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application.
Key Features:
Extremely easy to sand
Sets to a super hard finish
Highly crack resistant
Ready to use, dries in just 2 hours
For use exclusively on interior plasterboard & gyprock
How to Use:
Make sure the surface is clean, dry, and free from loose material.
Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly.
Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting.
For optimal results, apply a paint undercoat before using water or oil-based paint top coat.
Limitations & Tips:
Use Poly Gap filler or silicone sealant for areas with joint movement.
Clean up immediately with water before the filler dries.
For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution.
Polyfilla Skim Coat 510g is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job
Seamless Filler for Pro-Level Paint Preparations
When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 1.2kg. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application.
Key Features:
Extremely easy to sand
Sets to a super hard finish
Highly crack resistant
Ready to use, dries in just 2 hours
For use exclusively on interior plasterboard & gyprock
How to Use:
Make sure the surface is clean, dry, and free from loose material.
Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly.
Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting.
For optimal results, apply a paint undercoat before using water or oil-based paint top coat.
Limitations & Tips:
Use Poly Gap filler or silicone sealant for areas with joint movement.
Clean up immediately with water before the filler dries.
For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution.
Polyfilla Skim Coat 1.2kg is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Rapid 30 340g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces
Quick, Reliable, and Versatile Filler for All Surface Types
If speed is of the essence, Polyfilla Rapid 30 340g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces.
Key Features:
Extremely easy to sand
Sets to a hard finish
Highly crack-resistant
Fills up to 50mm deep holes
Dries in as fast as 30 minutes*
Suitable for multiple surfaces: plasterboard, brick, timber, and concrete
How to Use:
Clean and dry the surface, ensuring no loose or powdery material.
Press the filler firmly into dents and holes, feathering edges to minimize sanding.
Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications.
For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat.
Limitations & Tips:
Use Poly Gap filler where joint movement occurs.
Do not fill more than 50mm deep.
Clean up with water before the filler dries.
For quick paint-over solutions, consider using Poly Quick Dry.
*Drying time is based on a 2mm application.
With Polyfilla Rapid 30 340g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces
Quick, Reliable, and Versatile Filler for All Surface Types
If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces.
Key Features:
Extremely easy to sand
Sets to a hard finish
Highly crack-resistant
Fills up to 50mm deep holes
Dries in as fast as 30 minutes*
Suitable for multiple surfaces: plasterboard, brick, timber, and concrete
How to Use:
Clean and dry the surface, ensuring no loose or powdery material.
Press the filler firmly into dents and holes, feathering edges to minimize sanding.
Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications.
For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat.
Limitations & Tips:
Use Poly Gap filler where joint movement occurs.
Do not fill more than 50mm deep.
Clean up with water before the filler dries.
For quick paint-over solutions, consider using Poly Quick Dry.
*Drying time is based on a 2mm application.
With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Rapid 30 100g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces
Quick, Reliable, and Versatile Filler for All Surface Types
If speed is of the essence, Polyfilla Rapid 30 100g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces.
Key Features:
Extremely easy to sand
Sets to a hard finish
Highly crack-resistant
Fills up to 50mm deep holes
Dries in as fast as 30 minutes*
Suitable for multiple surfaces: plasterboard, brick, timber, and concrete
How to Use:
Clean and dry the surface, ensuring no loose or powdery material.
Press the filler firmly into dents and holes, feathering edges to minimize sanding.
Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications.
For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat.
Limitations & Tips:
Use Poly Gap filler where joint movement occurs.
Do not fill more than 50mm deep.
Clean up with water before the filler dries.
For quick paint-over solutions, consider using Poly Quick Dry.
*Drying time is based on a 2mm application.
With Polyfilla Rapid 30 100g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home.
Easy to sand, sets to a super hard finish and is highly crack resistant.
For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: White
• Surface to be filled should be clean and dry with no loose or powdery material.
• Exterior surfaces and metals (eg. nail heads) should be primed before application.
• Using the filling blade press filler in firmly and remove excess.
• Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications.
• For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer.
• Protect from rain until painted over.
.• For best results, apply paint undercoat before applying water or oil based paint top coat.
• Use Polyfilla Gap filler or silicone sealant where joint movement occurs.
• Clean up with water before filler dries
Q. Is there a filler I can use for both inside and outside?
A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home.
Easy to sand, sets to a super hard finish and is highly crack resistant.
Filling blade included
For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: White
Application
• Surface to be filled should be clean and dry with no loose or powdery material.
• Exterior surfaces and metals (eg. nail heads) should be primed before application.
• Using the attached filling blade press filler in firmly and remove excess.
• Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications.
• For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer.
• Protect from rain until painted over.
.• For best results, apply paint undercoat before applying water or oil based paint top coat.
• Use Polyfilla Gap filler or silicone sealant where joint movement occurs.
• Clean up with water before filler dries
FAQ's
Q. Is there a filler I can use for both inside and outside?
A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home.
Easy to sand, sets to a super hard finish and is highly crack resistant.
Filling blade included
For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: White
Application
• Surface to be filled should be clean and dry with no loose or powdery material.
• Exterior surfaces and metals (eg. nail heads) should be primed before application.
• Using the attached filling blade press filler in firmly and remove excess.
• Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications.
• For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer.
• Protect from rain until painted over.
.• For best results, apply paint undercoat before applying water or oil based paint top coat.
• Use Polyfilla Gap filler or silicone sealant where joint movement occurs.
• Clean up with water before filler dries
FAQ's
Q. Is there a filler I can use for both inside and outside?
A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Gloss Finish 390g: The Ultimate Surface Perfector for Flawless Gloss Paints
The Flawless Base for Glossy Elegance
Unlock the perfect preparation for your gloss paint projects with Polyfilla Gloss Finish 390g. Specifically designed for filling cracks and dents on doors, windows, trims, and more.
Key Features:
Easy to sand
Sets to a super hard, mirror-like finish
Highly crack resistant
Ready to use, dries in just 3 hours
For use on various surfaces, both interior and exterior
Common Applications:
Doors
Windows
Trim
Architraves
Skirting boards
Compatible Surfaces:
Plasterboard
Concrete
Timber
Primed metal
How to Use:
Ensure the surface is clean and dry. Press filler firmly into dents, holes, or splits.
Remove excess and allow to dry for 2-3 hours. For oil-based paint, allow longer drying times.
Sand with fine sandpaper for an immaculate finish. For best results, apply a second, thin coat and sand lightly before painting.
Limitations & Tips:
Not suitable for exterior timber likely to absorb excessive water.
Use Poly Gap filler or silicone sealant where joint movement occurs.
Clean up with water before the filler dries.
Protect from rain until painted over.
Do not use below 5°C.
For a surface that gloss paints will love, choose Polyfilla Gloss Finish 390g.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick.
Water, weather, UV, algae and mould resistant
Can be tooled to a render texture or sanded to a smooth finish.
For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Available in: 500g and 2.2kg
Colour: Cement grey in colour but can be painted over with both oil and water based paints
• Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap.
• Rinse thoroughly and allow surface to dry.
• Use flexible filling blade to press filler into hole, or trowel to spread a thin
layer over surface, and tool to a feathered edge.
• Allow to dry (2–3 hours in thin 2–3mm applications, depending on
temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather.
• For deeper jobs apply in 10mm layers, allowing each layer to dry before
applying the rest.
• Protect from rain until dry. If required, paint with a quality exterior coating.
• For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying.
• For best results, apply undercoat before applying water or oil based top coat.
• Where joint movement occurs, use a flexible Poly sealant.
• Clean up with water before filler dries.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick.
Water, weather, UV, algae and mould resistant
Can be tooled to a render texture or sanded to a smooth finish.
For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: Cement grey in colour but can be painted over with both oil and water based paints
• Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap.
• Rinse thoroughly and allow surface to dry.
• Use flexible filling blade to press filler into hole, or trowel to spread a thin
layer over surface, and tool to a feathered edge.
• Allow to dry (2–3 hours in thin 2–3mm applications, depending on
temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather.
• For deeper jobs apply in 10mm layers, allowing each layer to dry before
applying the rest.
• Protect from rain until dry. If required, paint with a quality exterior coating.
• For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying.
• For best results, apply undercoat before applying water or oil based top coat.
• Where joint movement occurs, use a flexible Poly sealant.
• Clean up with water before filler dries.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing.
Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out.
Can be stained, clear-finished, painted, nailed, screwed, sanded or planed.
For use on: Timber (EXTERIOR & INTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Available in: 450g and ^2kg
Colour: Dries to a pine colour
NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc.
• Ensure surfaces are clean and dry.
• Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary.
• Apply firmly with filling blade.
• Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity).
• For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather.
• Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish.
• For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing.
• Protect from rain until painted over.
• For best results, apply undercoat before applying water or oil based top coat.
• Where joint movement occurs, use a flexible Poly sealant.
• Clean up with water before filler dries.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing.
Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out.
Can be stained, clear-finished, painted, nailed, screwed, sanded or planed.
For use on: Timber (EXTERIOR & INTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: Dries to a pine colour
NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc.
• Ensure surfaces are clean and dry.
• Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary.
• Apply firmly with filling blade.
• Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity).
• For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather.
• Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish.
• For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing.
• Protect from rain until painted over.
• For best results, apply undercoat before applying water or oil based top coat.
• Where joint movement occurs, use a flexible Poly sealant.
• Clean up with water before filler dries.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink.
For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR)
Fill depth: Dependent on mix ratio
Dries in: 2-3 hours
Ready to use: NO (mix with water)
Available in: 500g, 1kg, 2kg & 6kg
Colour: Off-white
• Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key.
• Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate.
• Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge.
• Leave for 2-3 hours before sanding and decorating.
• For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area.
• Clean up with water before filler dries
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink.
For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR)
Fill depth: Dependent on mix ratio
Dries in: 2-3 hours
Ready to use: NO (mix with water)
Available in: 500g, 1kg, 2kg & 6kg
Colour: Off-white
• Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key.
• Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate.
• Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge.
• Leave for 2-3 hours before sanding and decorating.
• For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area.
• Clean up with water before filler dries
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink.
For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR)
Fill depth: Dependent on mix ratio
Dries in: 2-3 hours
Ready to use: NO (mix with water)
Available in: 500g, 1kg, 2kg & 6kg
Colour: Off-white
• Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key.
• Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate.
• Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge.
• Leave for 2-3 hours before sanding and decorating.
• For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area.
• Clean up with water before filler dries
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A vinyl reinforced cement-based filler that is water and weather resistant.
Matches cement grey when set and easily sands whilst maintaining the strength of cement.
Can be nailed and screwed without splitting or breaking.
Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc.
For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement.
Fill depth: Dependent on mix ratio
Dries in: 5-6 hours for sanding. Allow 24 hours before painting.
Ready to use: NO (mix with water)
Available in: 500g & 2kg
Colour: Grey and can be tinted by adding cement colorants to the mixing water.
Application tips:
• Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling.
• Coat nail heads with oil based paint prior to filling to prevent rust staining.
• Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time.
• For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper.
• Leave for 24 hours, and then apply a suitable primer/undercoat before painting.
• When applying in thin layers, do not over trowel.
• Clean up with water before filler dries
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A vinyl reinforced cement-based filler that is water and weather resistant.
Matches cement grey when set and easily sands whilst maintaining the strength of cement.
Can be nailed and screwed without splitting or breaking.
Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc.
For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement.
Fill depth: Dependent on mix ratio
Dries in: 5-6 hours for sanding. Allow 24 hours before painting.
Ready to use: NO (mix with water)
Available in: 500g & 2kg
Colour: Grey and can be tinted by adding cement colorants to the mixing water.
Application tips:
• Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling.
• Coat nail heads with oil based paint prior to filling to prevent rust staining.
• Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time.
• For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper.
• Leave for 24 hours, and then apply a suitable primer/undercoat before painting.
• When applying in thin layers, do not over trowel.
• Clean up with water before filler dries
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper.
Here are just a few specific uses (there are hundreds of other uses):
Replace broken knob on a drill press
Insulate wire connections, secure wire nuts
Rebuild and repair zinc or aluminium gear housing
Fill abandoned drill holes in aluminium or steel
Seal stainless steel electrical panel
Stop leaking drum
How to prepare a surface for bonding with PC-Metal™
Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants.
How to clean-up after PC-Metal™ application
We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover.
Can PC-Metal™ plug a hole in a 55 gallon drum?
PC-Metal™ is an excellent product for quickly plugging a hole made in a drum.
PC-Metal™ has a strong odor. Does the smell go away?
PC-Metal’s™ odour stops after it cures.
PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal?
PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals.
How fast does it cure? How much should be mixed?
PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness.
What kind of metal is in PC-Metal™? Does PC-Metal™ rust?
It is an alloy of iron and aluminium. It will not rust.
Can PC-Metal™ be machined? Can it be tapped or cut?
Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed.
Can PC-Metal™ be used to seal a cracked engine block?
PC-Metal™ has many automotive uses even repairs to engines.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-7® is the original tough job epoxy! This paste epoxy was originally formulated more than 60 years ago for the maximum in bonding power. Professionals to the do-it-yourselfers select PC-7® because of its exceptional adhesion to metals, ceramics, masonry and many plastics. PC-7® is designed for permanent repairs. Where other adhesives fail…PC-7® won’t! Choose PC-7® if you want to: seal a crack in a wall, attach a hanger to a ceramic plaque, seal a leak in an oil pan, repair a granite monument, fix a leak in PVC pipe connection, create a multimedia sculpture, and thousands of other repairs. When mixed, part A (gray) and the hardener part B (black) react to form a bond of tremendous strength. The PC-7® formulation is slow curing, but slow can be a good thing especially for large tasks.
WORKING TIME: 60 MINUTES
CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE)
PC-7® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Thicker than peanut butter but not as thick as bubble gum.
Here are just a few specific uses (there are hundreds of other uses):
Bond metal electrical boxes to concrete wall.
Fill cracks in basement walls.
Rebuild vintage Bakelite steering wheels.
Seal holes in oil and transmission pans or fuel tank.
Bond and repair stainless steel.
Attach transition strips on concrete floor.
Attach firing strips to concrete wall.
Bond to and rebuild hard rubber bumper.
How to prepare a surface for bonding with PC-7 Epoxy Paste
Remove contaminants such as dust, dirt, oil and grime with solvents such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be scuffed using sandpaper to increase adhesion.
How to clean-up after PC-7 Epoxy Paste application
Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-7® cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
How thick can I apply PC-7®?
PC-7® can be applied in any thickness. It does not require drying or exposure to air. It will cure from the inside out.
I made a repair with PC-7® but need to build the area up more. Can I apply more epoxy?
PC-7® sticks to PC-7®
Can I use PC-7® for a vertical repair?
PC-7® can be applied vertically and overhead. Because of its high viscosity it will not drip or sag.
How long does it take PC-7® to harden?
Normally, at 70F, PC-7® will cure in 24 hours but full hardness can take up to 48 hours. Cooler conditions will extend the cure time. Working in a garage or outside in temperatures between 50F and 60F may double the length of time needed for full cure. Applying PC-7® to a cool surface such as an exterior facing wall will slow down the cure.
Can I paint over PC-7® and if so how?
PC-7® should be primed then painted. Use Zinser Bullseye® 1,2,3 Stain Sealing Primer or Kilz® Premium Stain Sealing Primer or INSL-X® Stix Bonding Primer. Priming/sealing is important to separate and protect the finish coat from the epoxy/amine surface.
Can I use PC-7® on a finished surface?
Smooth, glossy or shiny surfaces should be roughened or scuffed with sandpaper to provide maximum adhesion. Use 80 or 120 grit sandpaper. A roughened surface has much more surface area than a smooth surface.
PC-7® is very thick. Can I smooth it out or thin it out?
Use a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol or Lacquer thinner to smooth applied PC-7®. Be-cause PC-7® is very thick and gooey, it is necessary to apply alcohol or acetone to the tool or gloved fingertips in order to lubricate the surface and shape or feather the applied epoxy.
Can I use more of one part of PC-7® in order to speed the curing?
Adding additional hardener does not make PC-7® cure faster. It is best to mix PC-7® one part of A to one part of B. However, PC-7® is probably the only epoxy that does not require precisely a 1:1 mix ratio. Plus or minus 25% A or B does not affect the performance. Adding additional PC-7® (+50%) part B hardener (black) can improve the adhesion to difficult surfaces such as PVC pipe and fittings. Measure equal volumes of part A epoxy (gray) and part B hardener (black) then measure an additional half portion of hardener (black). This will make the mix ratio (1 : 1.5, A : B).
Can I tint PC-7® to match a surrounding color?
PC-7® can be tinted with iron oxide or carbon pigments. Powdered pigments are used to color stucco or concrete and can be found at art supply stores. Universal tints that are used to color paint are compatible with PC-7®. Too much tint may affect the performance of PC-7®.
I want to do a repair outdoors and the epoxy seems really stiff?
PC-7® becomes more viscous in cool temperatures. Set the containers in a warm place prior to mixing. Acetone has been used to reduce the viscosity of PC-7®. The addition of acetone will contribute to shrinking and slow down the cure rate. PC-7® performs best without the addition of solvents.
What will PC-7® bond to?
It is easier to say what PC-7® will NOT bond to: Wax paper, Teflon, Plexiglass, vinyl and some softer plastics. Test an area if in doubt and always rough up shiny, smooth surfaces with sandpaper.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks.
WORKING TIME: 30 MINUTES
CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE)
PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter.
Here are just a few specific uses (there are hundreds of other uses):
Reattach missing swimming pool tiles.
Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat.
Repair cracked or damage swimming pool or hot tub skimmer.
Waterproof and Seal cracked fibreglass.
Seal screw holes to hatch lids or seating.
Attach fish locators to transom.
Repair stock tanks.
Repair broken refrigerator door shelf fixtures.
Repair broken pottery.
Repair shower basin or antique bath tub.
Seal leaking air conditioner drip pan.
Seal underground conduit.
How to prepare a surface for bonding with PC-11® Epoxy Paste
Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-11® Epoxy Paste application
Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
Can PC-11® be used in Aquariums?
There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed.
What plastics does PC-11® stick to?
PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite.
What plastics does PC-11® not stick to?
PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate.
What rubbers does PC-11® stick to?
PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers.
What temperatures can PC-11® be applied?
PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time.
Can gel coat be applied to PC-11®?
Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat.
Can PC-11® be painted?
Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat.
Will PC-11® yellow in direct sunlight?
Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important.
Can PC-11® be thinned with solvent?
PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible.
PC-11® is a simple one to one mix, but how accurately does the measurement need to be?
The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-SuperEpoxy® is a non-drip translucent paste epoxy suitable for conventional or static mixing. It has unlimited uses in bonding, assembling, filling and sealing most materials. Unlike conventional liquid epoxies, PC-SuperEpoxy® can be applied via a static mix nozzle vertically and overhead. It cures quickly at room temperature to form a resilient, non-conductive bond or seal that resists most chemicals, fresh and saltwater, gasoline and fuel oil. Works great bonding steel to wood, fibreglass, aluminium, concrete, brick, glass, block, ceramics, hard plastics and much more. PC-SuperEpoxy® is the toughest, highest strength epoxy we manufacture.
WORK TIME: 15 MINUTES AND TACK-FREE IN 60 MINUTES
CURE TIME: 4 HOURS (12 – 24 HOURS FOR FULL CURE)
Here is a product that can take on the most challenging of projects with ease.
Adhesion strength in excess of 2500 psi (up to 4000 psi).
PC-SuperEpoxy® is a gel with a consistency like Vaseline.
Here are just a few specific uses (there are hundreds of other uses):
Anchoring or securing railings to wood or fibreglass decking.
Seal cracks and holes in decking.
Attach chocks, cleats, handles and pulls.
Anchor or secure iron balusters to step and handrail.
Fill cracked wood beam.
Fix broken latch in the car glove box.
Attach axe head.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Marine™ Epoxy Putty Stick is a specially formulated epoxy putty suitable for wet or underwater applications. Incredibly it has an extended open time (20 – 30 minutes) but cures hard within 60 minutes for a fast return to service and emergency repairs. It sticks great to metals, fibreglass, tile, wood and some plastics such as ABS and rigid PVC.
Here are just a few specific uses (there are hundreds of other uses):
Seal holes and waterproof fittings
Shape and form missing corners or holes in ceramic or fibreglass fixtures
Re-attach and secure loose hardware
Fill cracks and dings in fibreglass
Seal leaks in water tanks
How to prepare a surface for bonding with PC-Marine™
Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Marine™ application
Wear disposable gloves to minimize contact with the skin. Use denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner to cleanup before PC-Marine cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying paint remover or paint stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
Can PC-Marine™ be applied underwater?
Yes, application underwater is possible. PC-Marine™ will adhere and cure underwater. However, it is preferable to apply it in dry conditions.
Is PC-Marine™ suitable for repairing canoes?
PC-Marine™ is excellent for repairs to aluminium and fibreglass canoes but not when they are made with Hypalon.
How much time does it take for PC-Marine™ to cure?
PC-Marine™ has an extended application or open time of 20 minutes. Most repairs made with PC-Marine™ can be returned to service after 60 minutes. Some applications may require a full 24-hour cure.
Is PC-Marine™ green?
PC-Marine™ Epoxy Putty stick is white on the inside and green on the outside. The green colour disappears when mixed with the white. The result is an off-white colour when it cures.
What is the maximum thickness that PC-Marine™ Epoxy Putty can be applied?
PC-Marine™ can be applied thick or thin. There isn’t a thickness limit. It cures from the within via a chemical reaction. It does not need to dry or be exposed to air.
How much PC-Marine™ can be mixed at a single time?
PC-Marine™ is slower curing than other epoxy putties allowing larger portions to be mixed at one time. Small quantities can be mixed more thoroughly and with less effort.
Can PC-Marine™ cure in a freezer?
PC-Marine™ is not recommended for sub-freezing temperatures. We recommend an application temperature of 2°C or higher.
Does PC-Marine shrink?
PC-Marine™ does not shrink.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Lumber™ Epoxy Putty is pre-measured and mixed by hand. It is used as a filler where a small amount will solve the problem. Within 60 minutes it is cured and ready. The putty can be easily formed and shaped.
Here are just a few specific uses (there are hundreds of other uses):
Reset or secure loose hardware in wood (hinges, handles, latches, etc.)
Fill abandoned screw and nail holes in cabinets or paneling
Fill dings and dents in molding or doors
Fill woodpecker and carpenter bee damage to exterior siding and paneling
Rebuild display corner in retail store
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Crete™ Epoxy is a hand-mixable, fast-setting epoxy putty that quickly repairs concrete and masonry. After mixing, it forms a concrete repair polymer that cures to a concrete-like color and texture. The mixture readily sticks to concrete and masonry surfaces and is easily shaped. It will stick to ceramics, glass, metals and some plastics. It cures within 60 minutes. Each stick contains pre-measured portions of activator and base — no measuring or mixing tools are necessary.
Here are just a few specific uses (there are hundreds of other uses):
Quickly rebuild small missing pieces of concrete
Fill holes in concrete and masonry
Rebuild missing pieces of statues and birdbaths
Seal hole for wire or conduit thru cinder block
Fill chip or spall in concrete furniture
Reattach loose or popped decorative stone
Fill crack in stone fireplace
Fill holes in brick or concrete walls; Apartment complexes, schools, government buildings etc.
Fill cracks in concrete or stucco wall before painting
Attach address numbers to brick or stone
Attach hardware to brick or stone
Fill abandoned screw holes and mounting holes in brick or cinderblock
Replace missing mortar
Seal rodent hole in cinderblock or concrete
How to prepare a surface for bonding with PC-Crete™
Old concrete must be clean and profiled or textured. Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Crete™ application
Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover.
Can PC-Crete™ be used to repair a crack in a fountain?
PC-Crete™ looks like concrete and is excellent for repairing concrete fountains, statues and lawn decorations.
Will PC-Crete™ adhere to a concrete step? Can it be shaped to match a corner?
PC- Crete™ is excellent to repairs on concrete surfaces such as steps. It shapes easily and can be sanded to match the look and texture of the concrete surface.
Is PC-Crete™ suitable for filling a small crack or spall in a sidewalk or deck?
Small crack repairs in concrete are easily made with or without the use of tools using PC-Crete™. PC-Crete™ is excellent for replacing missing or loose mortar between bricks and stones.
Can PC-Crete™ be used in a fish tank or pond?
PC-Crete™ is not recommended for aquatic use. Do not use this product in aquariums or ponds.
The PC-Crete™ is not easily grabbing or sticking to the concrete surface. It pulls away lifting loose stones
The putty wants to stick to the fingers more than the concrete surface. Wet the fingers with alcohol and then press, shape and smooth the applied putty. Also, loose stones can be wire brushed away to provide a sound surface.
PC-Crete™ does not have a smooth texture. It has particles throughout
The particles in PC-Crete™ are used to simulate the appearance of concrete.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER!
PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour.
Here are just a few specific uses (there are hundreds of other uses):
Fasten galvanized steel to a concrete floor.
Bond sheet metal to wood or masonry.
Seal and insulate electrical connections and electronic boards.
Protect electronic components from vibration and moisture.
Repair porcelain or sculptures.
Reattach multiple broken pieces in a vase.
How to prepare a surface for bonding with PC-Clear™ Epoxy
Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants.
Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Clear™ Epoxy application
Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy.
Cured epoxy can be removed with paint stripper or remover.
FAQ
Is PC-Clear™ Epoxy different from other clear epoxies?
Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing.
How does PC-Clear™ Epoxy’s strength compare to other epoxies?
PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi.
Is PC-Clear™ Epoxy brittle?
PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies.
How does outdoor exposure affect cured PC-Clear™?
Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing.
What is the best way to mix PC-Clear™?
How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life.
Why does PC-Clear™ Epoxy have a strong odor?
The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing.
Does PC-Clear™ Epoxy self-level?
PC-Clear Epoxy™ is a liquid and is self-levelling.
How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense?
PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead.
Can PC-Clear™ Epoxy be colored or tinted?
PC-Clear™ Epoxy can be tinted.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear.
High strength
Clear drying
Water clean up
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear.
High strength
Clear drying
Water clean up
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sandable
Paintable
Ready mixed
Weather resistant
Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home.
Sandable and paintable, it enables a smooth finish.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sandable
Paintable
Ready mixed
Weather resistant
Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home.
Sandable and paintable, it enables a smooth finish.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Partix Multipurpose Filler Powder This product is ideal for filling cracks, holes and gaps inside the home. It is strong and can be easily sanded to a smooth finish ready for painting. When dry, it can be nailed or screwed without splitting or breaking.
SUITABLE FOR
Interior repairs to plaster, brick, plasterboard, masonry and timber. For repairs where movement occurs, use Parfix Gap Filler.
PREPARATION
Ensure surfaces are clean, dry and free from dust and loose material. Glossy surfaces should be roughened with sandpaper to provide key.
MIXING
Add 2½ parts of Parfix Multi-Purpose Filler to 1 part water (by volume) and mix thoroughly into a smooth paste with a clean filling knife.
Once mixed, stays workable for up to 45 minutes.
Do not add water to extend working time. 4 Contamination with dried filler will shorten the working time.
APPLICATION
Press filler into crack with a flexible filling blade (overfilling slightly to allow for sanding back) then smooth off.
Wait 3-4 hours for filler to dry before sanding with a medium grade sandpaper Use a damp sponge to wipe away dist
CLEANING
Clean tools with water and reseal pack after use. Store in a cool, dry place.
PAINT PREPARATION
Before painting, apply a suitable primer/undercoat
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls.
High performance extra lightweight filler for all general interior and exterior repairs
Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials
Ideal for over-head applications (non-slump formula)
Properties
Ready to use
Will not shrink or sag
Super smooth finish – no sanding required
Paintable with all types of paint
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Easy to apply and shape
Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose materials.
Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Stir into a smooth paste (if the filler is too dry, just add a few drops of water).
Press filler into hole with a filling knife, smoothing off with a wet filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
No sanding is required. If sanding, wait for 24 hours.
If painting over with an oil-based finish, wait 14 days.
Must be painted over when used outside (minimum 2 coats).
Colour: White.
Not suitable for drilling.
Clean tools and hands immediately after use with warm water.
Do not store or use below 5 ° C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls.
High performance extra lightweight filler for all general interior and exterior repairs
Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials
Ideal for over-head applications (non-slump formula)
Properties
Ready to use
Will not shrink or sag
Super smooth finish – no sanding required
Paintable with all types of paint
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Easy to apply and shape
Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose materials.
Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Stir into a smooth paste (if the filler is too dry, just add a few drops of water).
Press filler into hole with a filling knife, smoothing off with a wet filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
No sanding is required. If sanding, wait for 24 hours.
If painting over with an oil-based finish, wait 14 days.
Must be painted over when used outside (minimum 2 coats).
Colour: White.
Not suitable for drilling.
Clean tools and hands immediately after use with warm water.
Do not store or use below 5 ° C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls.
High performance extra lightweight filler for all general interior and exterior repairs
Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials
Ideal for over-head applications (non-slump formula)
Properties
Ready to use
Will not shrink or sag
Super smooth finish – no sanding required
Paintable with all types of paint
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Easy to apply and shape
Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose materials.
Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Stir into a smooth paste (if the filler is too dry, just add a few drops of water).
Press filler into hole with a filling knife, smoothing off with a wet filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
No sanding is required. If sanding, wait for 24 hours.
If painting over with an oil-based finish, wait 14 days.
Must be painted over when used outside (minimum 2 coats).
Colour: White.
Not suitable for drilling.
Clean tools and hands immediately after use with warm water.
Do not store or use below 5 ° C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result.
Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco
Ideal for over-head applications (non-slump formula)
Excellent adhesion to all cementitious surfaces
Suitable for interior and exterior applications
Not suitable for use on damp surfaces
Tools Needed:
Filling Knife
Properties:
Ready to use
Will not shrink or sag
Easy to sand
Accepts nails and screws
Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint
Sandable after 24 hours
Accepts oil-based paints after 48 hours
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Colour: Light Grey
How to Apply:
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix well before use.
Product can be used directly from the pot.
Apply the product firmly in to the hole with a filling knife.
For a super smooth result, finish with a damp filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
Replace cover sheet after use and ensure lid is properly closed.
Once dry sand to a smooth nish.
Clean tools with warm water immediately after use.
Do not store or use under 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result.
Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco
Ideal for over-head applications (non-slump formula)
Excellent adhesion to all cementitious surfaces
Suitable for interior and exterior applications
Not suitable for use on damp surfaces
Tools Needed:
Filling Knife
Properties:
Ready to use
Will not shrink or sag
Easy to sand
Accepts nails and screws
Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint
Sandable after 24 hours
Accepts oil-based paints after 48 hours
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Colour: Light Grey
How to Apply:
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix well before use.
Product can be used directly from the pot.
Apply the product firmly in to the hole with a filling knife.
For a super smooth result, finish with a damp filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
Replace cover sheet after use and ensure lid is properly closed.
Once dry sand to a smooth nish.
Clean tools with warm water immediately after use.
Do not store or use under 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result.
Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco
Ideal for over-head applications (non-slump formula)
Excellent adhesion to all cementitious surfaces
Suitable for interior and exterior applications
Not suitable for use on damp surfaces
Tools Needed:
Filling Knife
Properties:
Ready to use
Will not shrink or sag
Easy to sand
Accepts nails and screws
Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint
Sandable after 24 hours
Accepts oil-based paints after 48 hours
Maximum layer thickness: 5 cm
Maximum depth: 10 cm
Colour: Light Grey
How to Apply:
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix well before use.
Product can be used directly from the pot.
Apply the product firmly in to the hole with a filling knife.
For a super smooth result, finish with a damp filling knife.
For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers.
Replace cover sheet after use and ensure lid is properly closed.
Once dry sand to a smooth nish.
Clean tools with warm water immediately after use.
Do not store or use under 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco.
For filling and repairing small cracks and holes, such as drill holes and nails
Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render
Not for use on metal, plastic, PVC and damp surfaces
Suitable for interior & exterior use
Tools Needed
Sharp Knife
Fine Sandpaper
Properties
Ready to use
Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint
Easy to sand
Will not shrink
Accepts nails and screws
Maximum layer thickness: 5 mm
Maximum depth: 5 mm
Must be painted over when used outside (minimum 2 coats)
Colour: White
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose materials.
Mix the product well before use.
Press filler into crack with a filling knife, smoothing off with a wet filling knife.
For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers.
Remove any excess filler and leave to dry.
Once dry sand lightly if required.
Clean tools and hands with warm water immediately after use.
Do not store or use below 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use.
Suitable for all types of interior & exterior wood
Quick drying, easy to sand
Water resistant finish will not shrink, crack or crumble
Stainable and paintable
Properties
Ready for use
Excellent adhesion to all types of wood
Tough and durable fill that flexes with the natural movement of wood
Accepts nails and screws
Sandable and paintable after approx. 3 hours (1 cm layer at 20°C)
Must be overcoated when used outside (minimum 2 coats)
Paintable with all types of paint
Maximum layer thickness: 1 cm
Maximum depth: 2 cm
Colour: natural/pine
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix the product well before use.
Product can be applied directly from the pot.
Apply filler firmly into the hole with a filling knife.
For a smooth result, finish with a damp filling knife.
For deeper repairs, build up in layers of 1cm, letting the product dry in between layers.
Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood.
Clean tools with warm water.
Do not store or use below 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use.
Suitable for all types of interior & exterior wood
Quick drying, easy to sand
Water resistant finish will not shrink, crack or crumble
Stainable and paintable
Properties
Ready for use
Excellent adhesion to all types of wood
Tough and durable fill that flexes with the natural movement of wood
Accepts nails and screws
Sandable and paintable after approx. 3 hours (1 cm layer at 20°C)
Must be overcoated when used outside (minimum 2 coats)
Paintable with all types of paint
Maximum layer thickness: 1 cm
Maximum depth: 2 cm
Colour: natural/pine
How to apply
Substrate must be clean, dry, dust and grease free.
Remove all loose material.
Mix the product well before use.
Product can be applied directly from the pot.
Apply filler firmly into the hole with a filling knife.
For a smooth result, finish with a damp filling knife.
For deeper repairs, build up in layers of 1cm, letting the product dry in between layers.
Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood.
Clean tools with warm water.
Do not store or use below 5°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled.
Recommended on:
Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone
Can be combined with fibreglass cloth for a durable patch
Great for crafting projects
Properties
Will not crack when drilled
Can be tinted to match surrounding materials
Water resistant: can be used outdoors
Does not shrink
One-time application
Convenient instant mix syringe
Consistently dispenses equal, uniformly mixed amounts of each component
Sets in 5 minutes
Quick completion of the project
How to Use:
Step 1: Safety Precautions
Well-ventilated area, gloves.
Step 2: Preparation
Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place.
Step 3: Application
Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it.
Step 4: Cleanup
Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
Fillers and repair compounds that sand smooth for paint-ready results. Choose fast-set for quick turnarounds or extended open time for shaping. Use filters to refine by chemistry and set speed. Always check the product page and TDS/SDS.
