![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
Fillers and repair compounds that sand smooth for paint-ready results. Choose fast-set for quick turnarounds or extended open time for shaping. Use filters to refine by chemistry and set speed. Always check the product page and TDS/SDS.
Sandable Finish
-
JB Weld JB Weld Plastic Weld Putty ABS, PVC, CPVC, Bumpers, Water Tanks
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be moulded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white colour, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first. GREAT FOR Rigid & Semi-flexible Plastic ABS, PVC & CPVC Pipes Automotive Trim & Bumpers Fibreglass Parts Vinyl Siding STRENGTH: 350 PSI SET TIME: 25 Minutes CURE TIME: 3 Hours CURE COLOR: Off White Drinking Water Safe USE ON Automotive Ceramic Epoxy Putty Sticks Fiberglass Plastic/Composite/PVC And More
$21.00
-
JB Weld JB Weld Plastic Bonder High Strenght Works on Carbon Fiber 25ml
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Fibreglass Plastic/Composite/PVC Wood And More PREPARE Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. MIX After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly. APPLY Apply with appropriate tool in an even coat, weld bead or extruded shape as needed. DRY Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
$18.00
-
JB Weld JB Weld Plastic Bonder 15 min High Strength Works on Carbon Fiber 25ml
Plastic Bonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. Plastic Bonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, Plastic Bonder sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Epoxy & Adhesives Fibreglass Plastic/Composite/PVC Wood And More
$19.95
-
JB Weld JB Weld MarineWeld Epoxy Waterproof For Boats Fiberglass Aluminum
MarineWeld™ is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminium, metal, composites, fibreglass and others. MarineWeld™ sets in 4-6 hours at room temperature and is fully cured to a dark grey colour in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters' surface. MarineWeld™ has a 1:1 mixing ratio and tensile strength of 5020 PSI. GREAT FOR Boats Personal Watercraft In/Outboard Engines Deck & Hull Accessories USE ON Fibreglass Under Water/Wet And More STRENGTH 5020 PSI SET TIME 4-6 Hours CURE TIME 15-24 Hours CURE COLOR Dark Gray
$22.00
-
JB Weld JB Weld KwikWeld Steel Reinforced Epoxy Multi Use x 25ml
KwikWeld™ is a fast-setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. KwikWeld™ has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. KwikWeld™ cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF. GREAT FOR Household Repairs Automotive Plumbing Marine Crafts & More USE ON Automotive Brick Ceramic Concrete And More
$16.00
-
JB Weld JB Weld HighHeat Temperature Resistant Epoxy Putty 57g
HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF GREAT FOR Exhaust Manifolds Tail Pipes Mufflers Engine Blocks Duct Work Machinery High Temperature Projects USE ON Automotive Metal And More
$25.00
-
JB Weld JB Weld Adhesiveweld Epoxy Drill it, Grind It, Machine It Fixes Fills and bonds Any surface 56.8g
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey color. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More STRENGTH: 3960 PSI SET TIME: 4-6 Hours CURE TIME: 15-24 Hours CURE COLOR: Dark Grey Use On: Automotive Brick Concrete Epoxy & Adhesives Fiberglass J-B Weld Metal And More
$15.50
-
Hypoxy AlumBond H-450 Repair Kit Epoxy Putty 184g
A two-component epoxy formula highly concentrated with carefully selected pure aluminium particles, modified curing agents, and special high quality additives to provide maximum strength, durability, and ease of application. APPLICATIONS: ALUMBOND is specially formulated for repairing HVAC copper pipes, HVAC condenser coils, tanks, valves, pumps, castings, water jackets, radiators, etc., where non-rusting, non-magnetic aluminum finish is desired. PHYSICAL PROPERTIES: Color Grey Pot Life 1 lb. @ 24ºC (75°F) 45 minutes Viscosity Non-sagging Paste Mixed Viscosity 330,000 cps Cure Shrinkage 0.0005 in/in Temperature Resistance 250°F (121ºC) Hardness (Shore, ASTM D 1706) 83D Cured Density 17.5 cu. in. per lb. Coefficient of Thermal Expansion 40 X 10- 6 cm/cm/ºC Compression Strength (ASTM D 695) 8,600 psi (59 M Pa) Tensile Strength (ASTM D 638) 3,500 psi (24 M Pa) Maximum Line Pressure (after 5 hours application time) 650 psi DIRECTIONS: Surfaces must be clean, dry, and preferably roughened for maximum adhesion. Dispense equal volumes of resin and hardener. Volume Ratio is 1:1. Mix thoroughly for 6 minutes making certain that all of the hardener comes in contact with all of the resin. Apply the mixed compound with a putty knife, spatula, or similar tool. The tool may be moistened with water to provide a smooth finish to the HY-POXY ALUMBOND. CURING TIME: At 75°F (24°C) a ½” (12.5mm) layer of HY-POXY ALUMBOND putty will be hard in approximately 45 minutes HY-POXY ALUMBOND will not cure properly below 40°F (4°C).
$85.00
-
Gorilla Original Gorilla Glue Bonds Virtually Everything Water Proof 59ml
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
-
Gorilla Gorilla Wood Glue Indoor and Outdoor Easy Applicator Bottle 532ml
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
-
Gorilla Gorilla Wood Glue Indoor and Outdoor Easy Applicator Bottle 118ml
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
-
Gorilla Gorilla Super Glue Precise GEL Precision Tip Tube 10 Sec 15g
Gorilla® Super Glue Precise Gel is an easy-to-use, thicker formula* combined with a precision tip and large tube, so it’s easy to apply with control and precision. Great for multiple surfaces and vertical applications. Directions 1. Protect work area from spills. 2. Clean and dry surfaces to be bonded. 3. To puncture, place cap and nozzle on the tube and tighten down. 4. Apply a small amount of Gorilla® Super Glue Precise Gel to one surface. Only one drop per sq. inch recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. 5. Press the two surfaces together for about 10-45 seconds. Wait 24 hours for full cure. 6. After using, clean nozzle with a dry cloth and replace the outer cap. Store in a cool, dry place.
$14.76
-
Gorilla Gorilla Super Glue Micro Precise Gel 5.5g - Instant, Strong Bonding, Controlled Dispensing for Various Surfaces
Glues Australia presents the Gorilla Super Glue Micro Precise Gel, an innovative adhesive solution tailored for a broad spectrum of applications. This product stands out as a versatile and powerful tool for creating enduring bonds in seconds. Product Features: Fast-Acting, Strong Formula: This glue sets in 10-45 seconds, providing a robust and lasting bond quickly. Controlled, No-Run Gel Formula: Its gel consistency ensures precise application, perfect for vertical surfaces and detailed projects. Versatile Bonding: Suitable for a variety of materials including plastic*, wood, metal, ceramic, rubber, and more. Directions for Use: Surfaces should be dry, clean, and free of dust. To open, turn the cap clockwise to puncture the seal. Open the nozzle by turning the green cap counter-clockwise. Dispense by squeezing, applying a small amount to one surface. Press surfaces together for 10-45 seconds. After use, clean the nozzle and store in a cool, dry place. Technical Specifications: Application Temperature: Room temperature Service Temperature Range: -65° to 220° F Cured Color: Clear Sandable: Yes Storage Tips: Store in a cool, dry location away from children and animals. Frequently Asked Questions: How does it differ from other Gorilla Glue products? It's a cyanoacrylate adhesive that bonds quickly without moisture or clamp time, unlike polyurethane-based Gorilla Glue. What is Impact Tough™? A formula designed to withstand bumps and drops, ensuring a strong and resilient bond. Can it bond all plastics? It is effective on most plastics, but certain types like polyethylene may need special preparation. How to remove from skin? For spills, immediately wash with soapy water. For cured glue, soak in warm soapy water, then gently wiggle the area. Is it food safe? It is not intended for any application involving food contact. Safety Information: For bonded skin or medical emergencies, contact Australian Poisons Information. The Gorilla Super Glue Micro Precise Gel is an essential addition to any toolkit. Its combination of strength, versatility, and ease of use makes it an ideal choice for various household and professional tasks. Available now at Glues Australia, it's the perfect solution for your adhesive needs."
$17.00
-
Gorilla Gorilla Super Glue Brush and Nozzle Dispenser 10 Seconds Set 10g
Gorilla Super Glue Brush & Nozzle offers 2 easy ways to dispense for control and accuracy. Brush & Nozzle features a precision tip nozzle and fine bristle brush that allow the user to control their super glue application, making it perfect for any project. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–45 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear, unlike any other super glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. Super glue, also referred to as cyanoacrylate glue, or CA glue works on a variety of materials, including plastic, metal, fabric, stone, ceramic, paper, rubber and more. It’s Gorilla tough, every time. Product Features -Two ways to dispense for greater control and versatility! -Fine bristle brush for controlled coverage with less mess -Precision tip nozzle for quick, easy dispensing -Impact Tough: Unique rubber particles increase impact resistance and strength -Fast-setting: Dries in 10-45 seconds, no clamping required. Directions -Protect Work Area From Spills -Clean and Dry Surfaces to Be Bonded -Apply Gorilla Super Glue -Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. -To use the nozzle, unscrew the upper cap and remove. To use the brush, unscrew the full cap and wipe the brush on the inner rim of the bottle to remove excess glue. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$15.00
-
Gorilla Gorilla Super Glue 10 Seconds Impact Tough 15g
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$14.99
-
Gorilla Gorilla Steel Bond GorillaWeld Bonds Metal Concrete PVC Fiberglas & More 29.5ml
GorillaWeld is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more! Features: INCREDIBLY STRONG: 4250 PSI STEEL BOND EPOXY SETS IN 10 MINUTES WATERPROOF** FORMS PERMANENT BOND DRIES DARK GRAY EASY TO USE BONDS: Metal, Plastic*, Concrete, PVC, Fiberglass, Ceramic & More! *Not recommended for use on polyethylene or polypropylene plastics. **Bonded wood materials should not be submerged or soaked in water. Directions All surfaces should be clean and free of debris. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. Remove cap from each tube and use top of cap to puncture foil seal. Dispense equal parts from each tube onto a clean, disposable surface. Mix with disposable mixing tool for approximately 20 seconds until the colour is uniform. Apply mixture to surface within 3 minutes. Clamp surfaces together and leave undisturbed for 10 to 30 minutes. Full cure in 24 hours. Cure time dependent on temperature, humidity and quantity applied. *Note: Not recommended for use on polyethylene, polypropylene or similar plastics. Specs: APPLICATION TEMPERATURE: 32°F to 90°F SERVICE TEMPERATURE: -40°F to 300°F SET TIME: 10 minutes CURE MECHANISM: 2 Part Reaction, requires mixing OUTDOOR: Yes FREEZE/THAW STABLE: Yes WATERPROOF: Yes* PAINTABLE: Yes SANDABLE: Yes DRILLABLE: Yes SHAPEABLE: Yes STAINABLE: No CHEMICAL RESISTANT: Limited EXPANDS WHEN CURED: No SHRINKS WHEN CURED: No CURED COLOR: Dark grey GAP FILLING: Yes *Not suggested to use on wood materials submerged or soaked in water Will GorillaWeld bond plastic/vinyl/rubber? Gorilla Weld will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP), polyethylene (PE) or similar plastics, or any type of rubber with high oil or plasticizer content. What does GorillaWeld work best for? GorillaWeld is ideal for metal and plastic (see above) substrates. GorillaWeld does not sag so it is ideal for vertical surfaces How should GorillaWeld be stored? GorillaWeld should be stored in a cool, dry place. Store away from children and animals. How do I mix GorillaWeld? GorillaWeld should be mixed 1:1 for 20 seconds or until uniform prior to application. Does GorillaWeld become hot during cure? Yes, mixing the hardener and resin together creates an exothermic reaction and will generate heat during cure. Consideration should be taken on mixing vessel as not to melt. How long do I have before GorillaWeld begins to harden? GorillaWeld will begin to harden after 3 minutes. Adhesive should be applied prior. What surfaces will GorillaWeld bond to? GorillaWeld is particularly suited for metal, plastic and other rigid surface bonding. Is GorillaWeld Food Safe? GorillaWeld is not recommended for direct or indirect food contact and should not be considered food safe. Why is GorillaWeld odour so strong? GorillaWeld is based on methyl methacrylate chemistry which has a naturally strong odour. We suggest using in a well-ventilated area. How do I remove GorillaWeld from body/skin? Uncured: GorillaWeld can be harmful through skin absorption and it is strongly recommended that you wear gloves during use. If GorillaWeld is on the skin, try removing with a dry cloth or paper towel and then wash the area thoroughly with soap and water. Cured: Cured material can be rolled off the skin. Remove as much cured material as possible and wash the area thoroughly with soap and water. For medical emergencies, call 1-800-420-7186 anytime How do I remove GorillaWeld from my surface? Uncured: Wipe up as much material as possible with a dry cloth and clean any remaining product/residue with Isopropyl alcohol (IPA) or acetone following solvent manufacturer’s instructions. Cured: For removing cured/dried GorillaWeld, mechanical means such as sanding or chiselling. What should I do if I think a human or animal has ingested GorillaWeld? For medical emergencies, call 1-800-420-7186 anytime
$15.82
-
FiberFix FiberFix Rigid Patch Hardens Like Steel UV Cured x 3 Patches
FiberFix Rigid Patch is the other cousin of the Repair Wrap- a fibreglass patch for permanent repairs on flat or hard-to-wrap surfaces. Simply apply the patch over the hole and expose to sunlight or UV light (but don't expose before applying!). In 3-5 minutes after exposure, the patch will cure! What's Included?: One 3"x3" patch, One 2"x8" patch, One 5"x5" patch Cure Time: 5-10 minutes (depending on the amount of sunlight/UV exposure) What Surfaces Will It Work On?: Any rigid surface (will not work on flexible surfaces such as fabrics or highly bendable plastic) Sandable/Paintable?: Yes! Applications: Rain gutters, fences, garbage barrels, water tanks, boats, canoes, automotive body, and much more!
$34.50
-
FiberFix FiberFix Repair Wrap 100x Stronger than tape Hardens like steel 5cm x 127cm
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$42.00
-
FiberFix FiberFix Repair Wrap 100x Stronger than tape Hardens like steel 3cm x 102cm
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$35.00
-
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](//gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](//gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
FiberFix FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$31.00
-
Dunlop Dunlop Floor Repairer Rapid Patch Mortar – 5kg
Dunlop Floor Repairer Rapid Patch Mortar is a high-performance, fast-setting compound ideal for repairing holes, cracks, and uneven surfaces on internal floors. Suitable for use prior to the installation of tiles, vinyl, carpet, or other floor coverings, it delivers a smooth, level finish ready for light foot traffic within 45 minutes and covering applications in as little as 2 hours. Surface Preparation: Ensure the substrate is clean, sound, and free of grease, dust, oil, paint, or other contaminants. Surfaces should be dry and firm. Smooth or sealed surfaces must be roughened or etched. For porous substrates like timber, fibre-cement, or plasterboard, priming may be required. For floors in direct contact with soil, a moisture barrier should be used before applying the patch mortar. Mixing Instructions: Add 5kg of product into approximately 1.5L of clean water in a clean container. Mix thoroughly with a mixing paddle to a lump-free, smooth consistency. Mix only what can be used within 15 minutes. Application Instructions: Apply with a steel trowel to the required thickness (up to 20mm in a single application). Shape and smooth the surface before the material begins to set. For deeper repairs, additional layers can be applied once the initial layer has set. Avoid adding extra water once mixed. Coverage: Approximately 3m² at 1mm thickness per 5kg bag. Coverage varies with surface texture and thickness applied. Drying Time: Initial set: ~45 minutes Ready for coverings (tiles, vinyl, carpet): ~2 hours Final cure: 24 hours (depending on thickness and ambient conditions) Clean Up: Clean tools and equipment immediately with water before the mortar sets. Technical Data: Type: Rapid-setting cementitious repair mortar Application Thickness: Up to 20mm Pot Life: 15 minutes Foot Traffic: 45 minutes Ready for Coverings: 2 hours Colour: Grey Shelf Life: 12 months in original unopened packaging stored in a dry area
$39.52
-
Bostik Bostik Epoxy Bond Industrial Strength Adhesive Multi Purpose 10ml
Bostik Epoxy Bond is a special two-part adhesive which, when mixed and allowed to set, produces bonds of immense strength. This resin based epoxy sets in approximately 5 minutes to give a permanent and colourless bond. It will adhere to pottery, china, metals, glass, wood, rigid and semi-rigid plastics and cardboard, etc. where an Industrial strength bond is required by handymen, hobbyists and tradesmen. FEATURES AND BENEFITS 1. Quick setting – will bond in 5 minutes 2. When fully cured, the adhesive can withstand boiling water for short periods of time. 3. Heat resistance rating of 60ºC temperature continuously. 4. Adhesive shear strength of up to 800 psi for metal/metal bonds APPLICATION 1. Surfaces to be joined must be clean, dry and free from dirt and grease. Metals should be abraded and washed with a petroleum solvent. China and pottery should be washed in detergent, rinsed and dried. 2. Dispense and mix thoroughly, sufficient material of the two parts to carry out the job at hand with a matchstick, screwdriver or similar implement. Reseal the nozzles of the syringe with the enclosed plug and tube with cap and store in an upright position (nozzles upward). 3. Apply a thin film of adhesive to one or both of the surfaces to be joined, press together and do not move until the adhesive has set - usually 5 minutes @ 20ºC. Very good handling strength is obtained after 20 minutes and maximum adhesion is achieved after 24 hours
$9.00
-
Blue Magic Blue Magic QuickSteel Steel Reinforced Epoxy Putty Metal Repair 57g
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$15.00
-
Blue Magic Blue Magic QuickSteel Aluminum Reinforced Epoxy Putty Metal Repair 56.8g
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$25.00
-
Selleys Araldite Quick Set Epoxy Adhesive 90 Second Bond Easy Mix Rigid Bond 24ml
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$28.96
-
Selleys Araldite 5 Minute Epoxy Adhesive Holds Up to 75Kg For Everyday Use Dries Clear 8ml
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
-
Selleys Araldite 5 Minute Epoxy Adhesive Holds Up to 75Kg For Everyday Use 24ml
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
-
3M 3M Bondo Professional Glazing & Spot Putty
Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Specifications Application Dent Fill Brand Bondo® Color White, Off white Product Type Glaze Putty Substrate Aluminum, eCoat or Paint, Galvanized, SMC Details Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Fast curing makes putty sandable in only 20 minutes Putty is compatible with all types of automotive paint systems Use during the Fill stage of the 3M™ Body Repair System Bondo® Professional Glazing & Spot Putty smooths and repairs pin holes, scratches, nicks, minor dents, stone chips and other surface imperfections in automotive paint and bodies. This product is a 2-part component formula that securely and quickly bonds to primer, metal, fiberglass and aluminum. Professional Quality Surface Blemish Repairs Bondo® Professional Glazing & Spot Putty quickly repairs paint scratches, minor dents and stone chips. Our professional quality formula comes as a two-part product with putty and cream hardener to produce a mixture that won't shrink once cured. This glazing and spot putty has a 5-minute working time and a 20-minute curing time, giving you the perfect balance of enough time to complete the repair with a fast cure that keeps your project moving forward on schedule. Perfect Repairs Every Time Once cured, you're ready to sand to create a smooth patch that matches the surrounding surface beautifully. Our repair putty securely bonds to primer, metal, fiberglass and aluminum, and it resists gumming up sandpaper and shrinking. It can be used with all types of paint systems for professional-looking results. Use During the Fill Stage of the 3M™ Body Repair System Even a small repair can seem complex at first. So 3M's Body Repair System simplifies the entire automotive body repair process by dividing it into four stages: Stage 1 — Prepare. This stage includes pulling dents, removal of paint and rust and efficient, effective masking of the area. Stage 2 — Fill. This stage involves patching holes with reinforced filler and smoothing and shaping filler before painting. Stage 3 — Paint. This stage includes painting the area and blending and smoothing primer and paint. Stage 4 — Finish. The final stage for showroom-grade results: removing small defects, sealing and polishing clear coats and other painted surfaces. 3M supplies premium products such as abrasives, tapes, body fillers and tools for every stage. This system helps you work easily, efficiently and successfully across the entire body repair process.
$75.00
You have seen 220 out of 220 products