In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Fine Coat Render is a high-performance, fibre-reinforced, polymer-modified render that produces a fine, closed finish with superior adhesion and flexibility. The embedded fibres and flexible polymers allow the render to tolerate the minor movement common to sheeted and composite walls, dramatically reducing the risk of surface cracking. It can be applied by standard trowelling methods or by spray, and a variety of decorative finishes can be achieved depending on how it is floated or sponged.Where to use itSuitable for indoor and outdoor use over an unusually wide range of substrates: FC sheet and blueboard, concrete and blockwork, sound painted surfaces (alkali stable and water resistant), existing render, AAC panels and blocks, and EPS foam panels. It is the go-to finishing render where substrate movement or mixed materials would defeat a rigid render.How to useEnsure the substrate is clean, sound and free of dust, oil and loose coatings; prime where the system requires. Mix the powder with clean water to a smooth, lump-free consistency and apply by steel trowel or spray at 2-10mm thickness. Rule off, allow the render to firm, then float, sponge or texture to the desired finish. A 20kg bag covers approximately 6.5m² at 2mm or 2.6m² at 5mm thickness. Clean tools with water before the render sets.Important notesStay within the 2-10mm application range per coat. Avoid rendering in extreme heat, wind or imminent rain, and protect the fresh surface from rapid drying. Painted substrates must be firmly bonded, alkali-stable and water resistant.Specifications
Size
20kg bag
Colour
Grey
Coverage
6.5m² at 2mm or 2.6m² at 5mm per bag
Application thickness
2-10mm
Reinforcement
Fibre-reinforced, polymer modified
SafetyCement-based powder — the wet mix is alkaline and dust can irritate airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in ventilation and wash skin after contact. Refer to the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Render Joint & Patch is a high-performance, two-in-one compound for rendering projects: it joints fibre cement sheet and blueboard before render is applied, and it patches cracks and holes in existing rendered surfaces up to 5mm deep or wide. Supplied premixed in a light grey colour that blends into most render systems, it takes the fuss out of preparation work — one pail handles both the sheet joints and the surface defects before your finishing coat goes on. The 4L size is perfect for repairs and smaller rendering jobs.Where to use itOn interior and exterior walls. As a jointing compound, use it over blueboard and fibre cement sheet prior to rendering. As a patching compound, use it over sound existing render to fill hairline cracks, chips, divots and small holes before re-coating or painting.How to useSurfaces must be clean, dry, sound and free of dust, loose render and contaminants. Stir the pail, then trowel the compound firmly over sheet joints (embedding tape where the sheet system requires) or press it into cracks and holes, striking off flush with the surrounding surface. Feather edges smooth with a trowel — the Dunlop Gauging Trowel gives a professional finish. Allow to dry fully before applying render, texture or paint, and wash tools in water straight after use.Important notesMaximum patch depth or width is 5mm — build deeper repairs in stages or use a repair mortar. Drying time lengthens in cold or humid conditions. Not intended for structural crack repair or designed movement joints.Specifications
Size
4L pail
Colour
Light Grey
Patch capacity
Cracks and holes up to 5mm (depth or width)
Location
Indoor and outdoor walls
SafetyWater-based compound — wear gloves and safety glasses, avoid skin and eye contact and wash off with water. Keep the pail sealed and out of reach of children, and read the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Render Joint & Patch in the 10L trade pail is a high-performance combination product that covers two essential preparation steps in one: jointing fibre cement sheet and blueboard ahead of rendering, and patching cracks and holes up to 5mm in existing rendered walls. Premixed to a smooth, light grey consistency, it goes straight from pail to trowel with no mixing, keeping preparation fast and consistent across large jobs. The 10L size is the economical choice for renderers and builders working across full elevations or multiple rooms.Where to use itIndoors and outdoors on walls. Use as a jointing compound over blueboard and fibre cement sheeting before render systems are applied, and as a patching compound over sound existing render to make good cracks, holes and surface defects up to 5mm deep or wide before re-rendering, texture coating or painting.How to usePrepare a clean, dry, sound surface free of dust, loose material and contaminants. Trowel the compound firmly across sheet joints, embedding jointing tape where required by the sheet manufacturer, and feather the edges flush. For patching, press the compound into the defect, strike off level and smooth the surface — the Dunlop Gauging Trowel helps achieve a professional finish. Allow to dry completely before over-coating, and clean tools with water while the product is still wet.Important notesRepairs deeper or wider than 5mm need staged applications or a dedicated repair mortar. Cold, damp or humid weather extends drying times. Do not use across designed movement joints — finish those with a flexible sealant.Specifications
Size
10L pail
Colour
Light Grey
Patch capacity
Cracks and holes up to 5mm (depth or width)
Location
Indoor and outdoor walls
SafetyWater-based product. Wear gloves and eye protection during use, avoid prolonged skin contact and wash exposed skin with water. Store sealed, keep away from children and consult the Safety Data Sheet before application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible FC Jointing Compound in the 8kg trade pail is a premixed, flexible jointing compound for fibre cement sheet and blueboard, formulated to prepare sheet joints before decorative coatings, texture finishes or render go on. Ready to use straight from the container, it removes mixing from the workflow entirely and keeps a consistent, workable body from the first trowel-load to the last. Its flexible acrylic formulation moves with the substrate to resist joint cracking, while strong adhesion keys the compound firmly to the sheet surface.Where to use itFor jointing fibre cement sheeting and blueboard on interior and exterior walls — cladding, facades, garage conversions, extensions and commercial sheeted walls — prior to painting, texture coating or rendering. The larger pail suits whole-wall and multi-room jobs where a 3kg pack would run short.How to useCheck that sheets are rigidly fixed and joints are clean, dry and dust-free. Apply the compound over each joint with a trowel or broad knife, embedding jointing tape where the sheet manufacturer requires it, then finish with a band approximately 75mm wide and 1mm thick, feathered smooth at the edges. Allow to dry completely before over-coating. Wet compound cleans off tools with water. Coverage is approximately 7 lineal metres per kilogram at 75mm width and 1mm thickness, so an 8kg pail joints in the order of 55 lineal metres.Important notesDesigned movement joints should be finished with a flexible sealant rather than jointing compound. Drying slows in cold or humid weather. Keep the lid sealed between uses and do not thin the product with water.Specifications
Size
8kg pail
Colour
Grey
Coverage
Approx. 7Lm per kg (75mm wide at 1mm thick)
Location
Indoor and outdoor walls
SafetyWater-based acrylic product. Wear gloves and eye protection during application, avoid prolonged skin contact and wash with water after use. Store sealed in a cool place away from children and refer to the Safety Data Sheet before starting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ready-to-Go Render is a premixed white render supplied in a resealable pail, ready to trowel straight onto the wall with no mixing, no dust and no wasted powder. Its easy trowel-and-float formulation makes it one of the most approachable renders for first-time renderers, while still giving experienced applicators a smooth, workable body. Applied at 1-5mm, it delivers a clean, uniform finish over a wide variety of common wall surfaces inside and out.Where to use itSuitable for indoor and outdoor projects over AAC panels and blocks, blueboard, brickwork, concrete walls and sound painted surfaces. Ideal for feature walls, fence walls, garden walls, patching over dated finishes and giving tired masonry a fresh, rendered look.How to useMake sure the surface is clean, sound and free of dust, oil and loose or flaking material; prime porous or painted surfaces as recommended. Stir the pail, then apply the render with a steel trowel to a thickness of 1-5mm, working in manageable sections. Rule off and finish with a float or sponge float once the render has firmed — the Dunlop Sponge Float gives a superior finish. For a higher build over uneven walls, first apply Dunlop Multipurpose Acrylic Render as a base coat and use Ready-to-Go Render as the finishing coat. Tools wash up in water.Important notesKeep within the 1-5mm application range per coat. Avoid rendering in direct hot sun, strong wind or when rain is expected; cold and humid conditions extend drying times. Reseal the pail to keep unused render workable.Specifications
Size
16kg pail
Colour
White
Coverage
Approx. 6m² at 1mm or 2m² at 3mm per 16kg
Application thickness
1-5mm
SafetyWater-based premixed render. Wear gloves and safety glasses, avoid skin and eye contact, and wash with water after use. Keep out of reach of children and refer to the Safety Data Sheet for detailed handling information.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible FC Jointing Compound is a premixed, flexible compound for jointing fibre cement sheet and blueboard before decorative coatings are applied. Because it comes ready to use straight from the pail, there is no on-site mixing, no powder mess and no guesswork about water ratios — simply open, stir and trowel. The flexible formulation accommodates the minor movement typical of sheeted walls, while its excellent adhesion delivers a reliable, crack-resistant joint. The compact 3kg pail is ideal for smaller sheeting jobs and repairs.Where to use itUse on interior and exterior walls to finish joints between fibre cement sheets and blueboard prior to painting, texture coating or rendering. It is the recommended first step in preparing sheeted facades, extensions and infill panels for a decorative finish.How to useEnsure sheets are securely fixed and joints are clean, dry and free of dust. Where the sheet system requires it, embed jointing tape in a first application of compound. Apply the compound over the joint with a trowel or broad knife in a band roughly 75mm wide and about 1mm thick, feathering the edges smooth into the sheet face. Allow to dry fully before over-coating with paint, texture or render. Tools clean up with water while the compound is wet. Coverage is approximately 7 lineal metres per kilogram at a 75mm width and 1mm thickness — around 21 lineal metres from this 3kg pail.Important notesNot a structural adhesive or gap filler for moving joints wider than the system allows — use a flexible sealant at designed movement joints. Cold or humid conditions extend drying time. Reseal the pail after use to keep the remainder workable.Specifications
Size
3kg pail
Colour
Grey
Coverage
Approx. 7Lm per kg (75mm wide at 1mm thick)
Location
Indoor and outdoor walls
SafetyWater-based acrylic compound. Wear gloves and safety glasses, avoid skin and eye contact, and keep away from children. Wash hands and tools with water after use, and consult the Safety Data Sheet for full handling advice.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Coloured Grout in the trade-size 15kg bag is built for big tiling jobs - whole houses, commercial floors and multi-room renovations. It is the same flexible, smooth-finish formula tilers rely on, with a stronger colour system for rich, even grout lines and Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth in wet areas. The grout works easily, ensures flush joints and leaves no pin holes.Where to use itSuitable for walls and floors, indoors and outdoors, over ceramic, porcelain, marble, granite and mosaic tiles. With a working range of 1mm to 8mm joints it handles fine wall tiling through to wide-format floor tiles, and the grey tones (Misty Grey and Slate Grey) are popular choices for high-traffic floors where joints need to hide everyday wear.How to usePrepare clean, dry joints raked free of adhesive. Mix with clean water to a smooth paste - or with Dunlop Primer & Additive to boost colour, flexibility, adhesion and stain resistance. Apply diagonally with a rubber grout float, pack joints full, remove excess, then sponge the tiles clean once the grout firms and polish off haze. Initial set is around 24 hours, showers can be wet after 3 days, and full cure is reached after 7 days.Important notesInclude about 15% wastage in quantity estimates. Mix batches with consistent water content to avoid colour variation across large floors.Specifications
Joint width
1 - 8mm
Coverage guide
Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyCement-based product - alkaline when wet and may irritate skin and eyes. Wear gloves and eye protection, avoid inhaling dust when emptying and mixing the bag, and wash after use. Keep out of reach of children; see the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Easy Clean Epoxy Grout is a high-performance, durable epoxy grout with superior stain resistance that stands up to most household chemicals. Unlike traditional epoxies it is genuinely easy to use and clean during application, and just as easy to maintain afterwards. It also contains Grout Shield, a powerful mould inhibitor that resists the growth of mould and bacteria, keeping joints looking better for longer.Where to use itIdeal for areas subject to high wear and for spaces where strict hygiene matters - kitchens, bathrooms, laundries and swimming pools. Use it indoors and outdoors on walls and floors with ceramic, porcelain, vitrified tiles, mosaics and non-moisture-sensitive natural stone. It fills joints from 1.5mm up to 15mm wide.How to useThe kit comes in three parts: Part A resin, Part B hardener and Part C coloured filler, mixed at approximately 2 : 1 : 5-7 by volume. Mix only what you can use within the working time, work the grout firmly into clean, dry joints with an epoxy float, then emulsify and clean the surface promptly with a lightly damp sponge before the epoxy sets. Finish by polishing the tiles once dry. Mix part-kits accurately if you split the kit across sessions.Important notesEpoxy grout sets chemically, so cleaning off residue promptly is essential - hardened epoxy is very difficult to remove from tile faces. Coverage varies with tile size and joint dimensions; as a guide a kit does approximately 8m² of 200 x 200 x 8mm tiles at 3mm joints.Specifications
Joint width
1.5 - 15mm
Coverage guide
Approx. 8m² per kit for 200 x 200 x 8mm tiles at 3mm joints
Tile types
Ceramic, porcelain, vitrified, mosaics, non-moisture-sensitive stone
Location
Walls and floors, indoor and outdoor
SafetyEpoxy resins and hardeners can cause skin and eye irritation and sensitisation. Wear gloves and eye protection, ensure good ventilation, avoid skin contact with uncured components, and wash immediately after any contact. Keep out of reach of children and read the Part A, Part B and colour pack Safety Data Sheets before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ultra-White Grout is a non-sanded, flexible cement-based grout that delivers a super smooth, brilliantly white finish between wall and floor tiles. Formulated with Grout Shield anti-mould and anti-bacteria technology, it actively resists the growth of mould and bacteria so joints stay looking cleaner for longer. The cured grout is water repellent, resists dirt pick-up and is easy to wipe clean, making it a favourite for bright, fresh bathrooms and kitchens.Where to use itUse Ultra-White Grout on walls and floors, indoors and outdoors. It is suited to ceramic, porcelain, marble, granite and mosaic tiles, and is designed for narrow tile joints between 1mm and 4mm wide where a fine, non-sanded finish is wanted.How to useEnsure joints are clean, dry and free of dust or adhesive residue. Mix the powder with clean water to a smooth, lump-free paste, then work the grout firmly into the joints on the diagonal using a rubber grout float or squeegee. Remove the excess as you go, then clean the tile faces with a lightly damp sponge once the grout has firmed. Polish off any remaining haze with a soft, dry cloth. Allow the grout to cure fully before exposing wet areas such as showers to water.Important notesCoverage varies with tile size, joint width and joint depth, and a wastage allowance of around 15% should be included when estimating. For wide joints over 4mm choose a sanded or wide-joint grout instead. Pair with Dunlop Grout Sealer for extra stain protection.Specifications
Joint width
1 - 4mm
Coverage guide
Approx. 6.7m² for 300 x 300 x 5mm tiles at 3mm joints (incl. 15% wastage)
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyCement-based product - the wet mix is alkaline and may irritate skin and eyes. Wear gloves and eye protection, avoid breathing dust when mixing, and wash hands after use. Keep out of reach of children and refer to the Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ultra-White Grout in the 5kg pack is a non-sanded, flexible grout that produces a super smooth, super white finish across larger tiling jobs. It contains Grout Shield anti-mould and anti-bacteria technology to resist mould and bacteria growth, and the cured joint is water repellent and easy to clean, helping white joints stay bright in busy bathrooms, laundries and kitchens.Where to use itSuitable for tile joints on walls and floors, indoors and outdoors. Use it with ceramic, porcelain, marble, granite and mosaic tiles wherever joints are between 1mm and 4mm wide. The 5kg pack size suits full bathroom renovations, splashback runs and floor areas where a 1.5kg pack would run short.How to usePrepare joints so they are clean, dry and raked free of adhesive. Mix the powder with clean water to a smooth, creamy paste and let it stand briefly before remixing. Apply diagonally across the joints with a rubber grout float, pressing the grout in fully and striking off the excess. Once firm, sponge the tile faces clean with minimal water, then buff away the haze with a dry cloth. Keep showers dry until the grout has cured.Important notesEstimate quantities from tile size, joint width and depth and allow roughly 15% extra for wastage. Not intended for joints wider than 4mm. Sealing with Dunlop Grout Sealer after curing improves long-term stain resistance.Specifications
Joint width
1 - 4mm
Coverage guide
Approx. 13.3m² for 300 x 300 x 5mm tiles at 1.5mm joints (incl. 15% wastage)
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid inhaling dust while mixing, and wash thoroughly after handling. Keep out of reach of children and consult the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Flexible Coloured Grout in the 5kg pack brings the same smooth finish and strong, consistent colour as the smaller pack, in a size suited to whole bathrooms, kitchens and floor areas. The formula is flexible and easy to work, ensures flush joints with no pin holes, and contains Grout Shield anti-mould and anti-bacteria technology that resists mould and bacteria growth so grout lines stay looking better for longer.Where to use itGrout walls and floors indoors and outdoors with ceramic, porcelain, marble, granite and mosaic tiles. Joints from 1mm to 8mm are covered, making it suitable for everything from fine mosaic work to wide-format floor tiles. In swimming pools, use White 200 mixed with Dunlop Primer & Additive.How to useRake joints clear of adhesive and ensure they are clean and dry. Mix the powder with clean water to a smooth, lump-free paste - or gauge with Dunlop Primer & Additive for enhanced colour, adhesion, abrasion and stain resistance. Work the grout diagonally into the joints with a rubber float, strike off the excess, then sponge clean once the grout firms and buff away residual haze. Initial set is about 24 hours, showers can get wet after 3 days, sealing is possible after 3 days and full cure takes 7 days.Important notesAllow roughly 15% wastage when estimating coverage from tile size, joint width and depth. Keep mixing water consistent between batches for uniform colour.Specifications
Joint width
1 - 8mm
Coverage guide
Approx. 0.55kg/m² for 200 x 200 x 8mm tiles at 3mm joints
Tile types
Ceramic, porcelain, marble, granite, mosaics
Location
Walls and floors, indoor and outdoor
SafetyContains cement - wet grout is alkaline and can irritate skin and eyes. Wear gloves and safety glasses, avoid dust when mixing, and wash hands after use. Keep out of reach of children and consult the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications
Size
3.5kg bag
Coverage
Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat)
Thickness
Feather edge to 3mm
Substrates
Concrete, tiles, sheet timber, Dunlop floor levellers
Walk-on time
15-30 minutes; coverings from 15 minutes
SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications
Size
8kg bag
Coverage
Approx. 27m² over concrete or 55m² over sheet timber (skimcoat)
Thickness
Feather edge to 3mm
Substrates
Concrete, tiles, sheet timber, Dunlop floor levellers
Walk-on time
15-30 minutes; coverings from 15 minutes
SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Level-Flex Timber Floor Leveller is a high performance, partially self-smoothing latex levelling screed developed specifically for timber floors. Supplied as a complete two-part kit in a handy pail, it combines a cement-based powder with a flexible latex liquid to deliver the adhesion, flexibility and water resistance needed when levelling over floors that move more than concrete does.Where to use itDesigned for indoor use over timber and concrete subfloors, it creates a smooth, flat surface ready for ceramic tiles, carpet or vinyl. It is a popular choice for renovating older homes with uneven timber floorboards or sheet flooring before new coverings are installed.How to useSand and prime timber floors first, and prime porous concrete with a plush broom application. Blend the latex liquid with the powder using a low-speed paddle mixer until smooth, then pour and spread with a trowel, allowing the screed to flow out and self-smooth. The floor is walkable in about 3 hours; lay ceramic tiles after roughly 12 hours (3mm screed), carpet after 24 hours and vinyl after 48 hours.Important notesIndoor use only, and the leveller must be covered by a finished floor covering. Timber must be sound, rigid and well fixed before levelling. Low odour formula makes it comfortable to use in occupied homes.Specifications
Size
15.9kg kit (powder plus latex liquid)
Coverage
Approx. 7m² at 1mm or 2.3m² at 3mm per kit
Thickness
Feather edge to approx. 12mm (thicker with aggregate)
Substrates
Timber and concrete
Walk-on time
3 hours
SafetyWear gloves, safety glasses and a P2 dust mask when handling the cement powder, and keep the room ventilated while mixing. Avoid skin and eye contact with the wet mix, wash after use and store the kit away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Timber Floor Leveller is a high performance, partially self-smoothing screed for timber floors, built on ARDEX Ardit technology. Unlike traditional two-part latex levellers, it is a convenient single-part formula - just add water - yet still delivers the excellent adhesion, flexibility and water resistance needed to level over timber substrates that flex underfoot.Where to use itFor indoor use over timber and concrete subfloors, creating a smooth, even base before installing ceramic tiles, carpet or vinyl. It is well suited to renovations where old floorboards or sheet flooring need flattening before new coverings are laid.How to useSand and prime all timber floors before application, and prime porous surfaces such as concrete using a plush broom. Mix the powder with clean water using a low-speed paddle mixer until smooth and lump free, then pour, spread with a trowel and let the screed flow out to a level finish. Apply from a feather edge up to 12mm neat, or up to 30mm with the addition of 2-5mm aggregate.Important notesIndoor use only and must be covered with a finished floor covering. Ensure timber floors are rigid and securely fixed before levelling. The no-odour formula suits occupied homes. Check the technical datasheet for covering wait times for your chosen flooring.Specifications
Size
16kg kit
Coverage
Approx. 10m² at 1mm or 3m² at 3mm per kit
Thickness
0-12mm neat; 12-30mm with aggregate
Substrates
Timber and concrete
SafetyThe cement-based powder is alkaline and dusty when dry. Wear gloves, eye protection and a P2 dust mask while mixing, ventilate the work area, avoid contact with skin and eyes, and wash thoroughly after use. Keep away from children and pets.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications
Size
20kg bag
Coverage
Approx. 12m² at 1mm or 4m² at 3mm per bag
Thickness
1-25mm per application
Substrates
Concrete
Walk-on time
3 hours (tiles 3 hours; vinyl and carpet 24 hours)
SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Multipurpose Floor Leveller is a cement-based levelling compound from Dunlop Trade (ARDEX Australia) that mixes with water into a smooth, free-flowing material for evening out rough or uneven concrete floors. It flows into low spots and finds its own level, leaving a flat base that is ready for foot traffic in around 2 hours and ready for tiles in about 4 hours, making it a dependable first step before laying new floor coverings such as carpet, vinyl or ceramic tiles.Where to use itSuitable for indoor and outdoor use over sound concrete floors, including living areas, kitchens, laundries and covered patios. It can also be used to form ramps or for bulk filling. It is designed for concrete substrates only and must always be covered by a finished floor covering.How to usePrepare the slab so it is clean, sound and free of dust or contaminants, and prime porous surfaces. Slowly add the powder to clean water while mixing with a low-speed paddle mixer for 2-3 minutes until lump free. Pour onto the floor, spread with a trowel and allow it to self-smooth. Apply up to 25mm in one application, adding 2-5mm aggregate for beds thicker than about 10mm.Important notesNot suitable for driveways or areas with vehicle traffic, and it cannot be left exposed as a wear surface. Sand can be added to create a trowelable screed for ramping. Always follow the technical datasheet for priming and mixing details.Specifications
Size
15kg bag
Coverage
Approx. 1.6kg/m² per mm (about 9m² at 1mm per bag)
Thickness
Up to 25mm per application
Substrates
Concrete
Walk-on time
2 hours (tiles after 4 hours)
SafetyCement-based powders are alkaline and can irritate skin, eyes and airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in a ventilated area, wash skin after use and keep out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Ready-to-Go Tile & Grout 250g (White) is a clever 2-in-1 product that works as both a tile adhesive and a grout, straight from the tube. There is nothing to mix and very little mess, which makes it a go-to for small tiling jobs, mosaics and quick repairs or touch-ups around the home. Backed by Dunlop's 10 year guarantee.
2-in-1 ready-to-use tile adhesive and grout
No mixing, no fuss, less mess
Contains Grout Shield antifungal protection
Ideal for mosaics, repairs and touch-ups
Suitable for joint widths of 1-5 mm
Indoor and outdoor wall use
About the formula
This white, pre-mixed paste bonds wall tiles and then fills the joints with the same material, so a single tube handles the whole repair. The built-in Grout Shield technology helps resist mould and bacteria, keeping finished joints looking cleaner for longer. Excess can simply be wiped away with a damp cloth while still fresh, and the resealable tube makes it easy to store for future touch-ups.
Where to use it
Indoors: wall tiles and mosaics in kitchens, splashbacks, laundries and living areas, plus general tile and grout repairs. Suitable over concrete, cement render, fibre-cement sheet, plasterboard and prepared painted surfaces.
Outdoors: exterior wall tiles and mosaics. When grouting outdoors, protect the area from extremes of weather for 7 days while it cures.
Tile types: ceramic, porcelain and marble wall tiles and mosaics (excluding moisture-sensitive stone).
How to use it
Prepare the surface so it is flat, firmly fixed, clean and dry, free of dust, oil, grease and loose material. Prime surfaces with Dunlop Primer & Additive and allow to dry.
Spread the adhesive with a 4.5-6 mm notched trowel to a minimum 1 mm bed. Press and slide each tile into position for full contact, adjusting within 60 minutes (at 23°C, 50% humidity).
Joints can be grouted immediately. Squeeze the material firmly into the joints and compact with a grout float or squeegee, scraping off excess from the tile face.
After about 15 minutes, wipe back excess with a damp, small-pored sponge, rinsing often.
Once the joint has hardened (approx. 6-24 hours), buff and polish the tiles with a clean, dry cloth.
Important notes
Not suitable for use in wet areas such as a shower recess, over Dunlop Waterproofing membrane, or in continuously immersed conditions.
Do not use the grout in expansion or movement joints.
For textured or matt tiles, test ease of cleaning on a spare tile first.
Designed for wall tiles and mosaics rather than heavy floor tiling.
Specifications
Brand
Dunlop
Product
Ready-to-Go Tile & Grout (2-in-1)
Colour
White
Size
250 g
Form
Pre-mixed, ready-to-use paste
Tile types
Ceramic, porcelain, marble, mosaics (excl. moisture-sensitive stone)
Surfaces
Walls
Location
Indoor and outdoor
Joint width
1-5 mm
Clean up
Water (while fresh)
Guarantee
10 year (Ardex Australia)
Safety
Causes skin irritation and may cause an allergic skin reaction. Causes serious eye damage and may cause respiratory irritation. Use only outdoors or in a well-ventilated area, and wear protective gloves, clothing, eye and face protection. Avoid breathing any mist, vapour or spray. If in eyes, rinse cautiously with water for several minutes, remove contact lenses if easy to do, and seek immediate medical advice. If on skin, wash with plenty of water and remove contaminated clothing. If inhaled, move the person to fresh air. Store locked up and keep out of reach of children. Always read the current Safety Data Sheet before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Araldite Ultimate Bond is a grey two-part epoxy adhesive engineered for the most demanding repairs, delivering a durable, long-lasting bond that holds up to 200kg/cm² when fully cured on stainless steel. It is the toughest of the Araldite range, designed to be tug and snap proof for fixes that need to stay put.
About this adhesive
Two-part system of resin (Part A) and hardener (Part B) mixed in a 2:1 ratio.
Bonds a wide range of surfaces with a strong, rigid, durable join.
Sets in around 5 minutes and is touch-firm fast, with a low-odour formula.
Made from 20% bio-based carbon.
Working (usable) time of roughly 3-4 minutes at 20°C, so mix only what you can apply.
What it bonds
China, ceramic and porcelain
Metal
Glass
Leather (pre-test for compatibility)
Rubber (pre-test for compatibility)
Wood and timber
Most rigid plastics
Where to use it
Indoor: repairing crockery, ornaments and ceramics, refitting loose furniture joints, bonding metal, glass and timber components, and general household fixes.
Outdoor: durable repairs on tools, garden and workshop items where a tough, weather-durable bond is required. Bond strength depends on substrate, bond size and surface preparation, and set times lengthen in colder weather.
How to use it
1. Abrade, clean and dry both surfaces so they are free of dust, grease and loose oxides.
2. Snap the cap from the plunger and carefully cut the sealed tips at the end of the nozzle.
3. Apply even pressure to the plunger to dispense both liquids onto a clean disposable surface (2:1 ratio) and mix thoroughly with a spatula.
4. Apply the mixed glue to both surfaces, then bring them together.
5. Hold in place with tape or weights if needed and avoid undue strain on the joint for at least 60 minutes. Cures in 24 hours; maximise the bond area (minimum 2.25cm²) for best performance after full cure.
Replace the cap on the nozzle for storage and clean up any uncured adhesive with acetone.
Important notes
Will not bond PTFE, polyethylene or polypropylene plastics.
Bond will soften above 60°C but strength is restored once the temperature returns to normal.
May discolour if exposed to UV. Full cure takes more than 72 hours.
Not recommended where a clear, invisible bond is required, as the cured adhesive is grey.
Specifications
Brand
Selleys Araldite
Product
Ultimate Bond Epoxy Adhesive
Technology
Two-part epoxy
Colour
Grey
Size
30mL
Mix ratio
2:1 (Part A : Part B)
Working time
Approx. 3-4 minutes at 20°C
Set time
Approx. 5 minutes
Cure time
24 hours (full cure >72 hours)
Holds
Up to 200kg/cm² on stainless steel when fully cured
Heat resistance
Softens above 60°C, strength restored on cooling
Clean up
Acetone (while uncured)
Safety
Danger. Part A causes skin and serious eye irritation and may cause an allergic skin reaction. Part B may be corrosive to metals, causes severe skin burns and eye damage, and may cause an allergic skin reaction. Do not swallow and avoid contact with skin and eyes. Wear eye protection and protective gloves when mixing or using, and avoid breathing dust, vapours or spray. Keep out of reach of children and keep in the original packaging. If medical advice is needed, have the product container or label at hand. Refer to the Safety Data Sheet for full handling information.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters.
Key Benefits
Clean paint edges that help minimise bleed on most interior surfaces.
Easy application with a smooth unwind and hand tearable backing.
Clean removal when used as directed on properly prepared surfaces.
Works with brushes, rollers, and spray for DIY and trade jobs.
Perfect For
Cutting in around ceilings, cornices, and trims
Protecting hardware, switches, and fittings
Two tone feature walls and accent colours
Masking glass, tiles, and metal fixtures during repainting
Surface Compatibility
Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first.
How To Use
Prep the surface: Ensure it is dry, dust free, and fully cured.
Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal.
Paint: Roll or brush away from the tape edge for best results.
Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise.
Pro Tips
Burnish the tape edge lightly to improve the seal on textured areas.
Apply light coats near the edge. Heavy wet coats can overwhelm any mask.
For long runs, overlap tape pieces by a few millimetres and press the overlap firmly.
Good To Know
Suitable for indoor projects and general decorating.
Store in a cool, dry place away from direct sunlight to maintain performance.
Available in popular widths to suit trim work and broad masking.
Frequently Asked Questions
Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first.
Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line.
Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings.
Why choose FibaFuse
Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement.
Smooth finishing with feathered edges that sand and paint cleanly.
No bubbling when properly embedded in compound for a flat, reliable seam.
Works with most compounds including setting type and ready mixed formulas.
Ideal for pros and DIY on new installs, repairs, and patchwork.
Best for
Joining plasterboard sheets on walls and ceilings
Butt and tapered edge joints
Repairs to cracked or previously patched seams
High traffic areas that need extra durability
How to use
Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required.
Bed coat Apply an even layer of joint compound over the seam at least the width of the tape.
Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets.
Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions.
Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next.
Finish Lightly sand, prime, and paint.
Pro tips
Keep knife pressure firm during embedding to avoid bubbles.
Use a wider knife for second and third coats to reduce sanding.
Prime before painting for a consistent sheen across joints and boards.
Product details
Brand
Gyprock CSR
Type
Paperless joint tape for plasterboard seams
Compatibility
Setting and ready mixed joint compounds
Applications
Walls, ceilings, butt joints, tapered edges, repairs
Frequently asked questions
Do I need to pre soak the tapeNo. Embed the tape directly into wet compound.
Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times.
Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting.
Good to know
Store flat and dry to maintain tape integrity.
Always wear appropriate PPE when sanding joint compound.
Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
High-Grade Neutral Cure Silicone
A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots.
Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying.
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour, so can be used in any environment without discomfort.
Easy to clean once applied, as it resists moisture, hot cooking oils, and steam.
Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch.
Temperature resistance: approximately -60°C to +150°C.
25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying.
Where can this product be used?
Showers and sinks
Metal, copper, and brass fittings
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper, and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine.
Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe.
Remove tape before the sealant skins. Clean tools immediately with mineral turpentine.
Avoid smearing on surrounding surfaces.
The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup.
When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish, complete painting prior to using the sealant as it cannot be painted over.
Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish.
Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures.
Safety Tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and Re-Use
Store in cool dry conditions, below 30°C.
The sealant should be used within 6 months after opening.
After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity.
For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge.
If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned.
Why you’ll love it
Exterior-grade flexibility: absorbs movement and vibration without cracking.
Non-shrink & non-sink: holds profile and edge detail after cure.
Won’t fall out: engineered adhesion for long-term durability.
Ready to use: straight from the tub — no mixing, no mess, no waste.
Paintable: achieves a seamless, colour-matched finish once dry.
No VOCs: low odour, solvent-free formula.
Interior / Exterior: versatile enough for both.
Proudly Australian: made and owned in Australia.
Where it works
Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates:
Timber: decks, window frames, trims, fascia, general carpentry repairs.
Masonry: brick, block, render and patching mortar-like defects.
Plasterboard: exterior-exposed linings under cover and general patching.
Metals & gutters: non-structural filling and profiling (clean, sound, free of rust).
Around pipes & penetrations: neat, gap-free finishing before painting.
Glass & surrounds: edge repairs and feathering prior to topcoating.
Ideal projects
Rebuilding weathered or rotten timber edges before repainting.
Filling cracks and surface imperfections in rendered walls.
Profiling and feathering joints and transitions for a paint-ready finish.
General exterior maintenance where a flexible, paintable filler is essential.
Directions
Surface Preparation
Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound.
Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required.
For best mechanical key, lightly abrade glossy surfaces and remove dust.
Application
Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use.
Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate.
Build up in thin layers for deep repairs, allowing each layer to firm before adding the next.
For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing.
Finishing & Painting
Allow to dry fully. Dry time varies with film thickness, temperature and humidity.
Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat.
Use quality exterior paints for weather-exposed areas.
Clean-Up & Storage
Clean tools and splashes with water while wet.
Reseal immediately after use to minimise skinning and reduce waste.
Store upright with lid sealed. Do not allow contents to dry out.
Good to know
Formulation is unaffected by normal temperature swings and resists cracking with vibration.
Designed for exterior flexibility yet also suitable for interior touch-ups.
For best results on deep voids, fill in multiple light applications rather than one heavy pass.
Specifications
Brand
Earl’s
Product
MulTflex® Exterior Flexible Filler
Type
Single-pack, ready-to-use flexible filler & adhesive
Use
Interior / Exterior
Paintable
Yes, once fully dry
VOC Content
No VOCs (as supplied)
Shrink / Sink
Non-shrinking, non-sinking
Flexibility
Resists cracking with vibration and movement
Clean-Up
Water (while wet)
Substrates
Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass
Finish
Satin-smooth when tooled with a wet knife or brush
Packaging
Ready-to-use tub
Country of Origin
100% Australian made & owned
Limitations
Do not apply to unsound, dusty or actively corroding surfaces without proper preparation.
Dry and cure times depend on depth and conditions; confirm dryness before painting.
Not intended for structural repairs.
Pro Tips
Feather edges wide for invisible paint blending on weathered timber and render.
Keep a small cup of clean water nearby to maintain a smooth final pass.
Deep cavities: bridge with successive thin layers for the most stable result.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ready to use, hard drying acrylic putty filler
Ideal for repairing cracked, broken or uneven surfaces
30 minute fast drying time
Includes bonus applicator
Suitable for fibrous cement, brick, plaster and wood surface repairs
available in 500gm/1.5kg
Not suitable for wet areas or where structural movement occurs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*.
Provides superior water resistance, mould and soap scum resistance
White For Life – Always looks like new*
Resists yellowing, staining and blackening*
Crack resistant
Sand free - resists scratching files
Suitable for indoor wall and floor tiles
Comes in a cartridge for minimum wastage
Where can this product be used?
Bathrooms
Showers (walls only)
Toilets
Laundries
Kitchens
What materials is this product suitable for?
Ceramic tiles
Porcelain tiles
Stone tiles
Most other tiles
Please contact your store to confirm avaliability, as some stores may have a limited range.
How to Use
Preparation
For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult.
Application
Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time.
Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint.
Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets.
Allow grout to firm up in joints for approx 20 min (longer in colder conditions).
Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints.
Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks.
overage
1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
Limitations:
Not for areas frequently immersed in water eg. Shower floors.
Allow to dry for 3 days before exposing grout to water on shower walls.
Handy tips
If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas.
*To maintain whiteness and long term stain & mould resistance:
Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard.
Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners.
Areas subject to high foot traffic will require frequent cleaning.
Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes.
Coverage guide
1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
Clean Up
Clean up tools with water before product hardens.
Uncured product may be removed with water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SANDING BLOCKS offer optimal sanding results on flat, contoured and irregular shapes.
• Flexible, to conform to contours and irregular shaped objects.
• For sanding and cleaning metal, wood, plaster, plastic, fibreglass etc.
• Can be used for wet or dry sanding.
• Rinse with water to clean.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications.
Environmentally friendly
Non-toxic
Tough & flexible
Easy to use
Weather-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Eazy Tape Plasterboard Joint Tape, your ultimate solution for achieving flawless walls and durable repairs. Designed for both the DIY enthusiast and the professional, this self-adhesive fibreglass mesh tape is engineered to simplify your plasterboard wall panel joining or patching tasks. Crafted from high-strength fibreglass mesh, it ensures a robust bond that complements both plaster filler and jointing compounds seamlessly.
Why choose Eazy Tape? Here are the benefits:
Easy to Use: With its self-adhesive backing, the application is straightforward and mess-free, adhering securely to surfaces without the need for additional glues.
DIY-Friendly, Professional Results: Whether you're tackling a home project or a professional job, Eazy Tape guarantees a smooth, professional finish.
Strong Bonding & Holding Power: The superior fibreglass mesh material provides exceptional strength, reducing the risk of cracks and ensuring longevity.
Quick Results: Speed up your repair or construction projects with a tape that sets quickly, allowing you to move on to the next step without delay.
Perfect for a wide range of applications, from repairing cracks to joining new wall panels, Eazy Tape Plasterboard Joint Tape is the dependable choice for achieving seamless results with ease.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Eazy Tape Plasterboard Joint Tape, your ultimate solution for achieving flawless walls and durable repairs. Designed for both the DIY enthusiast and the professional, this self-adhesive fibreglass mesh tape is engineered to simplify your plasterboard wall panel joining or patching tasks. Crafted from high-strength fibreglass mesh, it ensures a robust bond that complements both plaster filler and jointing compounds seamlessly.
Why choose Eazy Tape? Here are the benefits:
Easy to Use: With its self-adhesive backing, the application is straightforward and mess-free, adhering securely to surfaces without the need for additional glues.
DIY-Friendly, Professional Results: Whether you're tackling a home project or a professional job, Eazy Tape guarantees a smooth, professional finish.
Strong Bonding & Holding Power: The superior fibreglass mesh material provides exceptional strength, reducing the risk of cracks and ensuring longevity.
Quick Results: Speed up your repair or construction projects with a tape that sets quickly, allowing you to move on to the next step without delay.
Perfect for a wide range of applications, from repairing cracks to joining new wall panels, Eazy Tape Plasterboard Joint Tape is the dependable choice for achieving seamless results with ease.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job
Seamless Filler for Pro-Level Paint Preparations
When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 510g. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application.
Key Features:
Extremely easy to sand
Sets to a super hard finish
Highly crack resistant
Ready to use, dries in just 2 hours
For use exclusively on interior plasterboard & gyprock
How to Use:
Make sure the surface is clean, dry, and free from loose material.
Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly.
Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting.
For optimal results, apply a paint undercoat before using water or oil-based paint top coat.
Limitations & Tips:
Use Poly Gap filler or silicone sealant for areas with joint movement.
Clean up immediately with water before the filler dries.
For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution.
Polyfilla Skim Coat 510g is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job
Seamless Filler for Pro-Level Paint Preparations
When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 1.2kg. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application.
Key Features:
Extremely easy to sand
Sets to a super hard finish
Highly crack resistant
Ready to use, dries in just 2 hours
For use exclusively on interior plasterboard & gyprock
How to Use:
Make sure the surface is clean, dry, and free from loose material.
Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly.
Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting.
For optimal results, apply a paint undercoat before using water or oil-based paint top coat.
Limitations & Tips:
Use Poly Gap filler or silicone sealant for areas with joint movement.
Clean up immediately with water before the filler dries.
For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution.
Polyfilla Skim Coat 1.2kg is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames.
For use on: Wood & metal (EXTERIOR & INTERIOR)
Dries in: Skins over in 2-3 days depending on weather conditions.
Ready to use: YES
Colour: Light brown
Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material.
• Bare timber should be primed with an oil-based primer before applying putty.
• Knead putty thoroughly for smooth, even consistency in application.
• Apply putty to working area with either a thumb or putty knife. When evenly
applied, smooth off.
• Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat.
Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product?
A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla P10 Gap Filler Rapid: The Ultra-Fast Solution for Perfect Fills
Features
Flexible
Smooth Finish
Rapid Drying Paintable in 10 minutes*
Low Shrinkage
Crack-Resistant*
Applications
Ideal for filling gaps around cornices, wall joints, skirting boards, as well as inside windows and door frames.
Usage Instructions
*To avoid paint cracking, apply to gaps no larger than 5mm deep and 10mm wide at temperatures above 20°C. Allow the sealant to dry before painting. Avoid applying paint too thickly.
When to Use
Paintable in just 10 minutes, allowing for fast project completion.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polyfilla Gloss Finish 390g: The Ultimate Surface Perfector for Flawless Gloss Paints
The Flawless Base for Glossy Elegance
Unlock the perfect preparation for your gloss paint projects with Polyfilla Gloss Finish 390g. Specifically designed for filling cracks and dents on doors, windows, trims, and more.
Key Features:
Easy to sand
Sets to a super hard, mirror-like finish
Highly crack resistant
Ready to use, dries in just 3 hours
For use on various surfaces, both interior and exterior
Common Applications:
Doors
Windows
Trim
Architraves
Skirting boards
Compatible Surfaces:
Plasterboard
Concrete
Timber
Primed metal
How to Use:
Ensure the surface is clean and dry. Press filler firmly into dents, holes, or splits.
Remove excess and allow to dry for 2-3 hours. For oil-based paint, allow longer drying times.
Sand with fine sandpaper for an immaculate finish. For best results, apply a second, thin coat and sand lightly before painting.
Limitations & Tips:
Not suitable for exterior timber likely to absorb excessive water.
Use Poly Gap filler or silicone sealant where joint movement occurs.
Clean up with water before the filler dries.
Protect from rain until painted over.
Do not use below 5°C.
For a surface that gloss paints will love, choose Polyfilla Gloss Finish 390g.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink.
For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR)
Fill depth: Dependent on mix ratio
Dries in: 2-3 hours
Ready to use: NO (mix with water)
Available in: 500g, 1kg, 2kg & 6kg
Colour: Off-white
• Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key.
• Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate.
• Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix.
• Use a clothes peg to reseal the pack.
• Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge.
• Leave for 2-3 hours before sanding and decorating.
• For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area.
• Clean up with water before filler dries
Products that level to a clean, smooth surface with minimal tooling, ideal for visible seams and cosmetic repairs. Use filters to refine by chemistry, viscosity and cure profile. Always review the product page and TDS/SDS.
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Monarch Mini Gap Filler [Brown]](//gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](//gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
