Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
Use for handy jobs around the office, house, garage
$1.50
Glue Dots® Repositionable Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for hanging lightweight items, securing rugs to hardwood and tile floors, and can be easily removed. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$8.73
Repositionable Dots™ Dot N Go® dispenser fits in the palm of your hand and can be used as a 'second set of hands' to hold small, lightweight items in place temporarily. It's perfect for quick fixes and repairs around the home. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$9.70
Advanced Strength Dots™ Dot N Go® fits in the palm of your hand and is perfect for quick fixes and repairs. With a small footprint, the Advanced Strength Dot N Go stores easily in a toolbox or drawer for easy access. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free Adhesive Size: 3/8 in. diameter Adhesive Color: Amber Quantity: 125 Adhesives
$8.95
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$7.98
Craft Glue Dots® are versatile, permanent adhesives ideal for heavier materials like wood or metal, large embellishments or thick cardstock. Glue Strength - Super-Strength Features/Benefits: Hand-held Dispenser | Easy to Use Acid Free| Photo Safe Non Toxic | Kid Friendly Specifications Adhesive Size: 3/8 in. diameter Adhesive Color: Clear Quantity: 200 Adhesives
$12.74
An adhesive for general woodworking applications. It is also ideal for Art and Craft applications and school supplies. Great to make slime. Ideal to bond paper wood, ceramic, porcelain and fabrics. Boyle PVA glue is suitable for porous surfaces such as wood, laminated board, leather, textiles, cork, paper, felt, styrene foam, cardboard, paper mache, decoupage collage, fabric flowers and more. Non-toxic Dries clear
$14.00
Bostik Super Glue is a multipurpose glue that bonds most non-porous materials in seconds. It dries to a clear, permanent bond with exceptional tensile strength up to 210 kg per square cm. Recommended Uses: -Precision work -DIY projects -Home handyman projects -Electrical -Optical -Watch -Jewellery -Car accessories -Materials Designed to stick: -Metal -Ceramic -Wood -Most plastics - (not polyethylene or polypropylene) -Natural and synthetic rubber -Leather Features: -Dries clear -Exceptional tensile strength up to 210kg per square cm -Enables precision work due to its small size
$5.20
Fast, strong and resistant super glue gel Product overview Bostik Fix & Glue Gel is the latest technology available in the market, which sticks in a few seconds and provides a strong, long-lasting bond. Its gel consistency makes it suitable for vertical surfaces. It is easy to use through its precise nozzle, in which the product will remain liquid for up to 12 months. Most importantly, Fix & Glue Gel is solvent-free and odourless – making it a safer option. Product Details Flexible and durable bond resists knocks and drops Water & temperature resistant Solvent-free Non-irritant, and odourless No respiratory allergens Recommended Uses Bostik Fix & Glue Gel is a great repair solution, in particular for vertical surfaces. Bonds almost all materials, including: Porcelain Ceramic Glass Mirror Leather Wood Paper Metal Fabric Hard plastic Tiles Concrete Brick Stone
$3.99
Fast, strong and resistant super glue gel Product overview Bostik Fix & Glue Gel is the latest technology available in the market, which sticks in a few seconds and provides a strong, long-lasting bond. Its gel consistency makes it suitable for vertical surfaces. It is easy to use through its precise nozzle, in which the product will remain liquid for up to 12 months. Most importantly, Fix & Glue Gel is solvent-free and odourless – making it a safer option. Product Details Flexible and durable bond resists knocks and drops Water & temperature resistant Solvent-free Non-irritant, and odourless No respiratory allergens Recommended Uses Bostik Fix & Glue Gel is a great repair solution, in particular for vertical surfaces. Bonds almost all materials, including: Porcelain Ceramic Glass Mirror Leather Wood Paper Metal Fabric Hard plastic Tiles Concrete Brick Stone
$9.21
Bostik Super Glue is a multipurpose glue that bonds most non-porous materials in seconds. It dries to a clear, permanent bond with exceptional tensile strength up to 210 kg per square cm. Recommended Uses: -Precision work -DIY projects -Home handyman projects -Electrical -Optical -Watch -Jewellery -Car accessories -Materials Designed to stick: -Metal -Ceramic -Wood -Most plastics - (not polyethylene or polypropylene) -Natural and synthetic rubber -Leather Features: -Dries clear -Exceptional tensile strength up to 210kg per square cm -Enables precision work due to its small size
$4.98
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Bostik Nail It Fast Cure White: The Acrylic Adhesive for Rapid, Strong & Odorless Bonds Product Overview Bostik Nail It Fast Cure is a fast-curing, versatile acrylic adhesive that offers strong and durable bonds. It's easy to apply and almost odorless. Key Benefits Solvent-free formula Suitable for EPS and XPS Non-corrosive towards metal Easy to apply and clean Applications Specifically developed for bonding: Wood, chipboard, hardboard uPVC to brickwork, stone or concrete Ceramic tiles to porous substrates Limitations Not suitable for PE, PP, PC, PMMA, PTFE, soft plastics, neoprene, and bituminous substrates. Not designed for continuous exposure to water or for movement joints. Application Instructions Apply the adhesive in a ventilating manner, using vertical stripes or dots. Material should be placed by shoving and pushing firmly. Surface Preparation All substrates must be solid, clean, dry, and free from grease and dust. For porous substrates, priming may be required. Cleaning & Maintenance Tools and uncured material can be cleaned with water or Methylated Spirit. Cured material must be removed mechanically. Bostik HANDY WIPES are recommended for cleaning hands. Colour Options Available in white.
$6.96
Non-toxic PVA glue that is non-staining and dries clear. Ideal for models, masks and other craftwork. Non-staining and specially developed to easily wash off clothes, hands and upholstery, even when dry! Made in Australia
$9.95
These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent-free and non-toxic. Bostik Glu Dots are also available in an extra strength version, for permanent applications. Key Features Repositionable Transparent, non-visible Solvent-free and non-toxic Acid and lingin free, suitable for photographs Description Bostik Removable Glu Dots are little circles of double-sided, clear adhesive which stick almost anything including paper, wood, plastic, metal, glass and painted surfaces. These non-yellowing dots are easy to use, acid and lignin free, making them ideal for use in the home, office and school as an alternative to drawing pins, staples or tape. They are solvent free and non-toxic. Bostik Glu Dots are also available in an EXTRA STRENGTH version, for permanent applications. APPLICATIONS - Holding up posters, cards, certificates, notices, maps, menus, calendars, messages, timetables, learning aids, children paintings, decorations, etc. - Keeping in place telephones, mouse pads, pens, candles, figurines, vases, calculators, ornaments, etc. - Keeping picture frames straight. - Sticking photos in an album. - Ideal for school projects, scrapbooking, art and craft projects. ADHESION Bostik Removable Glu Dots sticks extremely well to non-porous surfaces such as metal, glass, plastics, vinyl coated and painted surfaces and porous surfaces such as paper, boards, cloth, and wood. LIMITATIONS - Not suitable for highly absorbent, damp or dusty surfaces. - Not suitable for holding up heavy objects. - May damage delicate papers on removal. Safety Instructions: Bostik Removable Glu Dots is non-toxic. The product poses a choking hazard if ingested. In the event of ingestion, the mouth should be washed with water. Seek medical assistance if irritation or discomfort persists. Refer to our Safety Data Sheet for further toxicological information and comprehensive handling instructions. Surface Preparation: Ensure that surfaces are clean, dry and free of any dust, grease and loose materials. How to Use: 1. Tear along the perforations. 2. Peel off the paper backing. 3. Press the dot firmly onto the first surface. 4. Remove the clear film. 5. Press the second surface firmly onto the dot. 6. Reposition if necessary Cleaning Remove dots carefully by rubbing and rolling them off. Use mineral turpentine to remove any remaining residue. Storage The shelf life of the product is indefinite if stored at room temperature. Packaging 64 Glu Dots in a wallet
$9.95
Bostik Fine & Wide Clear Glue is a liquid gum general purpose stationery adhesive that dries clear. It is a clear PVOH (Polyvinyl Alcohol) liquid adhesive with two applicators, a non-drip pen applicator that flows in a fine clean line as well as a spreader. Recommended Uses Scrapbooks Cut and paste activities School projects Papercraft Intricate work Materials Designed to stick: Paper Cardboard Fabric Features Dual applicator Pen applicator that flows in a fine clean line Spreader applicator for covering large areas YOUR SMART ADVANTAGES − Dual applicator - Quality clear PVOH liquid gum adhesive - Dries clear - Pen applicator that flows in a fine clean line, ideal for intricate work - Spreader applicator for covering large areas - Sits easily in the hand - Non-toxic safe for all the family - No mess or waste - Does not contain food ingredients such as wheat, gluten, flour, egg, nut or milk products Uses: Bostik liquid gun general purpose stationery adhesive. Bostik Fine & Wide Clear Glue Pen and a clear PVOH (Polyvinyl Alcohol) liquid gum adhesive with two applicators, a non-drip pen applicator that flows in a fine clean line as well as a spreader. - Bonds paper, cardboard and fabric - Ideal for scrap-books cut and paste activities, school projects and paper craft PRODUCT CHARACTERISTICS Specification Complies to Australian Standard 8124.3 as well as European Standard EN71 for Mechanical and Physical properties, flammability of toys and Migration of Certain Elements Colour Transparent Physical Form Free flowing adhesive Appearance White free flowing liquid, slight odour APPLICATION 1. For the detailed applicator, turn top anti-clockwise. Squeeze gently. 2. Glue will flow smoothly, just as you need it. To reseal, turn top clockwise to prevent leakage. 3. For the spreader simply remove the cap and squeeze gently, spreading adhesive as required. 4. Once finished, wipe away excess glue off the spreader and refit protective cap. STORAGE AND SHELF LIFE Store in cool, dry conditions between 5 to 35ºC out of direct sunlight.30°C. Do not freeze
$5.10
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$28.96
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$19.26
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
You have seen 117 out of 117 products
Low-hazard, solvent-free choices that minimise fumes and emissions while delivering reliable bonds and seals. Ideal for occupied spaces and sensitive environments. Use filters to refine by chemistry, cure profile and finish. Always check the product page and TDS/SDS for application and safety details.
