Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
Hold It Australia T77 STUDLOCK High Strength for Bolts 25mm and Above - 50ml Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases. Applications Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts. Instructions for Use Clean all surfaces with a cleaning solvent and allow to dry. If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator. Shake the product thoroughly before application. Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole. Assemble components and tighten to the required torque level. Allow the adhesive to fully cure before applying load. Active & Inactive Metal Table Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
$34.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.10
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder
$30.14
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
You have seen 55 out of 55 products
High-strength adhesives for load-bearing assemblies and durable repairs. Surface prep, accurate mixing and clamping are critical—follow cure schedules closely. Use filters to refine by chemistry, pot life and temperature rating. Always check the product page and TDS/SDS.
