Davco Grey One Pot Premixed Tile Adhesive is a high-performance, ready-to-use acrylic-based adhesive, perfect for interior wall and floor tiling. Its premixed formula eliminates the need for onsite preparation, providing excellent adhesion and ease of application for both professionals and DIYers. Surface Preparation: Ensure all surfaces are sound, dry, and free from dust, oil, grease, or any other contaminants. Painted or glossy surfaces should be roughened and cleaned. For porous surfaces, priming may be required to ensure maximum adhesion. Application Instructions: Stir the adhesive thoroughly before use. Using a notched trowel, apply the adhesive to the substrate. Only spread as much adhesive as can be tiled within 20 minutes. Firmly press tiles into the adhesive, ensuring full coverage on the tile back. Adjust tiles within 20 minutes of placing them. Allow adhesive to set for 24 hours before grouting. Coverage: Approximately 0.75–1.25 m² per litre using a 6mm notched trowel. Coverage may vary depending on substrate and trowel size. Drying Time: Allow 24 hours before grouting. Full cure achieved within 7 days under normal conditions. Clean Up: Clean tools and excess adhesive with water immediately after use. Once dried, adhesive is more difficult to remove. Technical Data: Appearance: Grey paste Base: Acrylic Open Time: 20 minutes Adjustment Time: 20 minutes Application Temperature: 5°C to 35°C Ready for Grouting: After 24 hours
$30.24
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
CLR Calcium, Lime & Rust Remover Need to tackle tough calcium and lime deposits as well as rust stains? CLR Calcium, Lime & Rust Remover is a powerful formula that quickly and easily dissolves and removes tough calcium and lime deposits as well as surface rust stains from bathtubs, toilet bowls, sinks, glass, chrome, fiberglass, stainless steel, kettles, humidifiers, dishwashers, washing machines and showerheads. The formula also is ideal for use on caravans and boats. CLR Calcium, Lime & Rust Remover is part of the EPA’s Safer Choice Program recognising the product as a safer alternative to chemicals. The fast-acting, powerful CLR formula is septic-safe and contains no phosphates. Always spot test in an inconspicuous area before beginning to clean. What can you clean with CLR ? CLR cleans what many household products can’t. It dissolves and removes tough stains from the build-up of calcium, limescale and surface rust from hard water. You may not know what these are but chances are you’re living with them. Some examples where CLR can be used are; poor performing showerheads dishwashers washing machines shower screens inside your kettle on your taps inside and outside toilet bowls sinks on cloudy glass inside and outside chrome fiberglass stainless steel humidifiers surface rust stains on tools taps Plus many more. If you have a specific surface that you would like to know can be cleaned with CLR, search the material on our Frequently Asked Questions to find the answer. If it is not there – contact us. When you say diluted, how much water to CLR do I use? Use equal parts CLR to water i.e. 1 cup CLR mixed with 1 cup water. Is it septic safe? Yes, CLR is septic safe How do I use on a stain in my toilet? Wear household gloves. Mix equal parts CLR and warm water. Apply directly to stain with a brush, cloth or sponge. Rinse promptly with cold water. If the stain does not disappear use CLR full strength, wipe and rinse properly. How long should I leave CLR on the stain for? We recommend you do not leave on the stain for longer than a few minutes. Do not leave CLR on the stain and walk away from it. Always rinse thoroughly. Can I use CLR on my car (radiator, window etc)? No. Not recommended for use on cars as it may damage paintwork and/or interiors. Can I use on my chlorinated swimming pool tiles? No. CLR can react with pool chlorine leading to potentially dangerous reactions which must be avoided. What is the main ingredient in CLR? Calcium Lime Rust, more commonly known as CLR, is a household cleaning product used for dissolving stains, such as calcium, lime, and iron oxide deposits. Its ingredients include water, lactic acid, gluconic acid, lauramine oxide,Propylene Glycol, n-Butyl Ether, and solvents that dissolve cobalt gel coats and paint. How do you use CLR? Test the solution on a hidden area before applying to the entire surface. Apply directly to the calcium, lime or rust stain with a brush, cloth or sponge and rinse promptly with cold, clean water. Never leave CLR on an area for longer than two minutes. Safer Choice Finding cleaning and other products that are safer for you, your family, and the environment should be easy — that's why the U.S. EPA developed a Safer Choice label. We all play a role in protecting our families’ health and the environment. Products with the Safer Choice label help consumers and commercial buyers identify products with safer chemical ingredients, without sacrificing quality or performance. CLR, CLR Bathroom and Kitchen, CLR Outdoor Furniture Cleaner all wear the Safer Choice label to communicate that the product’s formula contain ingredients with more positive human health and environmental characteristics than conventional products of the same type. They are also biodegradable.
$24.12
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
Bostik Seal it Kitchen & Bathroom White: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Seal it Kitchen & Bathroom Translucent: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
$21.22
$12.61
$8.13
$12.69
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$25.07
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts -Bonds a variety of surfaces -Dries Clear -Very Strong, durable bonding -Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) -Forms a rigid, durable bond -Can be used for gap filling (surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Clamping is recommended to achieve a stronger bond -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Bond strength weakens above 80°C but strength is regained when temperature drops Appearance: Translucent Where can this product be used? -Load bearing repairs -Gluing the head back on your hammer -Fixing loose table or chair legs. -Bonding solid pieces of Aluminium sheeting -Bonding timber on your boat -Repairing splits and cracks in Cricket bats -Bonding fibreglass sheets -Repairing Ski’s -Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics -Crystal -Leather How to use this product -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. Handy tips -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Clamping recommended for a stronger bond. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. -Ensure the surface is dry before applying the product. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention -Non-toxic when set. -For further information refer to the Material Safety Data Sheet (MSDS). -Storage and re-use -Ensure caps are replaced and product stored in a cool dry place.
$20.05
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.45
You have seen 210 out of 210 products
Professional-level performance for strength, durability and productivity on site. Expect defined movement capability, temperature/chemical ratings and precise application methods. Use filters to refine by chemistry and pot life. Always review the product page and TDS/SDS.
