Get clean, precise application of glues, epoxies, resins, oils, inks, and other liquids with this easy to use 30 ml syringe and blunt tip fill needle. Ideal for workshop, craft room, electronics bench, and on site repair jobs where accuracy matters and mess is not an option. Why you'll like it Controlled dispensing for dots, lines, seams, and small cavities 30 ml capacity for longer runs without constant refilling Graduated barrel with clear volume markings for repeatable dosing Luer lock connection keeps the needle securely attached during use Reusable barrel when used with compatible liquids and cleaned after use Blunt tip needle for safe, non piercing filling and application Common uses Injecting Fix-A-Floor through grout lines to re bond hollow or loose tiles Precision placement of two part epoxies and cyanoacrylate gels Applying PVA wood glue into tight joints and dowel holes Wicking thin adhesives along hairline cracks Filling small voids and seams before clamping Electronics work with flux, solder paste, and conformal coatings Craft, model making, leatherwork, and jewellery repairs Tile repair tip: A blunt tip of about 2 mm to 3 mm fits most grout lines. Drill a small hole in the grout as directed by the adhesive manufacturer, inject until the cavity is filled, then clean any squeeze out promptly. What is included 1 × 30 ml syringe barrel with plunger 1 × blunt tip fill needle with luer lock hub 1 × protective cap for storage Specs Capacity 30 ml Connection Luer lock Needle style Blunt tip, non piercing Barrel material Transparent polypropylene Plunger seal Latex free elastomer Use For adhesives and shop liquids only, not for medical use How to use Attach the blunt tip needle by twisting it onto the luer lock until snug. Pull back the plunger, draw in your adhesive, then tap the barrel to release trapped air. Dispense with slow, steady pressure for consistent beads and dots. For Fix-A-Floor, inject through the grout holes until filled and follow the cure steps on the product label. After use, expel remaining liquid if suitable, then flush the barrel and needle using a cleaner compatible with your adhesive. Dry completely and cap for storage. Compatibility tips Works well with PVA, polyurethane, epoxy, acrylic, latex, and many hobby liquids. For solvent based products, confirm compatibility with polypropylene before use. Do not store reactive two part mixes inside the syringe after they begin to cure. Safety Not sterile and not for medical, food, or body use. Wear gloves and eye protection when handling chemicals. Keep out of reach of children. FAQ Can I reuse itYes, if your adhesive and cleaner are compatible with polypropylene and the luer lock needle. Clean immediately after use for best results. Will it work with thick glueYes, but very thick products may require more pressure and a wider blunt tip size. Does it come sterileNo. This set is for industrial, workshop, and hobby applications only.
$18.00
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$26.95
![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram. The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time. Features & Benefits of Timbermate No Waste, Usable to the last drop. If tub dries out just add water to soften. Won't Shrink, Sink, Crack or Fall Out. Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc. Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one. Available in 13 Timber Tones plus Natural. Use White for top coats only. Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc. Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use. Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time. Clean hands or tools with water. Non-Flammable, Non-Toxic, Non-Yellowing. Solvent, Latex and Acrylic Free. Heat Proof and Freezeproof. Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc. Takes nails, screws, planing, sawing, drilling and routing Can be used on Metal, Plastic, Fibreglass and in Foundries. 100% Australian Made and Owned. Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg. Interior Grade. Edgefiller Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat. Woodfiller/Wood Putty Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time." You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats. Grainfiller Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required. MDF Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs. Flooring Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement. Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished. Frequently Asked Questions Question: Is TIMBERMATE toxic, flammable or harmful? Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable. Question: Can TIMBERMATE be used externally? Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler. Question: Can TIMBERMATE be used with stains and other finishes? Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers. Question: Can TIMBERMATE be grainfilled? Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc. Question: How is the grainfiller applied? Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry. Question: When is the stain applied? Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours"). Question: How are the colours matched? Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain. Question: How long does TIMBERMATE take to dry? Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light. Question: What depth or width can be filled? Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers. Question: Why is the tub hard some days and feels dry and soft on other days? Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten. Question: How is TIMBERMATE softened? Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable. Question: Can TIMBERMATE be used for any other purpose other than wood repair? Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting. Question: Can TIMBERMATE go off or does it have a shelf life? Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate. Question: Why are so many colours available? Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base). Question: What is Tint Base (Natural) putty and why? Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour. Question: Can TIMBERMATE be used on floors? Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors. Question: Can TIMBERMATE be used with French Polish and Waxes? Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE. Question: How is an incorrect match or badly filled hole fixed? Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary. Question: Is TIMBERMATE Australian owned and manufactured? Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.
$10.29 - $239.00
Earl’s MulTfill is a premium, ready-to-use multi-purpose filler designed for fast, clean, and durable repairs across interior and exterior projects. The heavy-bodied formula spreads smoothly, levels cleanly, and dries hard without shrinking, sinking, cracking, or falling out. With zero VOCs and no acrylics, latex, or solvents, it’s a low-odour choice for homes, workshops, and job sites. Clean-up is simple with water, and once dry MulTfill sands easily to a fine, paint-ready surface. Why you’ll love it Ready from the tub: no mixing, no mess, no wastage — just open, apply, and close. Zero VOCs: stable, low odour and user-friendly. Non-sinking, non-shrinking: fills stay flush and true. Won’t fall out: dries hard for lasting repairs. Paintable finish: accepts most coatings for a seamless result. Sands like a dream: refined finish without clogging when sanded dry. Long shelf life: keep the lid sealed and it’s ready when you are. Where it works Use MulTfill on common building materials including wood (including weathered and damaged sections once sound), masonry, plasterboard, cement sheet, concrete, and primed metal. It’s ideal for nail holes, dents, shallow voids, corner repairs, skim touch-ups, and general surface preparation before painting. Colour options White, Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut. How to use Prep: Ensure the area is clean, dry, and sound. Remove loose material and dust. For best glide, lightly wet your putty knife. Apply: Press firmly to fill the defect and smooth off. For deep voids, apply in layers up to 6 mm per pass, allowing each layer to dry before the next. Sand: Once fully dry, sand with 120 grit or finer to achieve a smooth, level surface. Coat: Prime if required, then paint. For clear finishes, tint the filler with suitable colorants or oxides before application to harmonise with surrounding material. Cleanup & care: Clean tools with water. If product thickens in the tub, add a few drops of clean water and stir until smooth. Always reseal promptly. Pro tips Feather edges wide when blending across boards or wall patches. On exterior jobs, protect from rain during cure and overcoat appropriately for exposure. Tinting before clear coats helps the repair visually disappear on timber substrates. Specifications Brand Earl’s Product Type Multi-purpose paintable putty / filler (water-based) Use Interior and exterior VOC Zero VOC Contains No acrylic, latex, or solvents Substrates Wood, masonry, plasterboard, cement sheet, concrete, primed metal Application Thickness Up to 6 mm per layer; allow to dry between layers Sanding Dry sand; 120 grit or finer Overcoating Accepts most paints; for clear coats, tint filler first for best colour match Clean-up Water Colours White; Teak (Cypress), Ebony, Grey, Jarrah, Merbau, Walnut Pack Sizes 140 g, 600 g, 1 kg, 2 kg, 3 kg (varies by colour) Shelf Life Up to 5 years if sealed and stored correctly Country of Origin Australia Storage Keep container tightly closed when not in use. Store in a cool, dry place out of direct sun. Avoid prolonged freezing. If product thickens, add a few drops of water and mix to restore spreadability. What’s in the tub A smooth-spreading, heavy-bodied filler that levels cleanly, sands easily, and delivers a paint-ready finish across interior and exterior surfaces — with no mixing, no fuss, and no strong odour.
$8.70 - $54.81
![Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]](http://gluesaustralia.com.au/cdn/shop/files/Sikasil_pool_white.webp?v=1760227901&width=645)
Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance. Key Features Excellent resistance to chlorinated water and common pool chemicals Movement accommodation of ± 25 % Neutral cure — non-corrosive, safe on most metals and tile systems High elasticity and recovery Very good resistance to fungal attack Suitable for interior and exterior applications Typical Applications Underwater joints in swimming pools Wet areas, such as spas, splash zones, and shower recesses Sealing between tiles, concrete, glass, and metal substrates Technical Highlights Service temperature range: –40 °C to +80 °C Shore A hardness (28 days): ~20 Elastic recovery: > 90% Typical curing speed: ~2 mm per 24 h Skinning time: ~5 minutes (23 °C / 50% RH) Available in White, Grey, and Transparent shades Shelf life: 15 months (when stored unopened between 5 °C and 25 °C) Usage & Application Tips Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease). Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application. Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended. Apply a closed-cell foam backing rod to control joint depth. Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time. Allow full cure (minimum 7 days) before filling pool with water. Limitations & Precautions This product is not suitable for: Joints in direct contact with potable food or drink Overpainting Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber) Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.
$29.76 $0.10/ml
Agnews Water Putty - Hard-Setting Filler for Wood, Plasterboard, Concrete & More Agnews Water Putty is a professional, powder-based repair and levelling compound for durable, long-lasting results. Mix only what you need with clean water, then patch, level or rebuild surfaces with confidence. Once cured, it sets rock hard, bonds permanently, and can be sawn, drilled and sanded to a smooth, paint-ready finish. Key features Brand: Agnews Unlimited shelf life when stored dry Non cracking, non shrinking, non sinking Won't fall out – adheres firmly and fills to any depth Interior & exterior grade (seal exterior applications after full dry) Non flammable and no VOCs Mix what you need for minimal waste Suitable substrates Plasterboard, concrete, wood/timber, cement sheet, masonry. Also suitable for minor floor levelling and feathering on concrete, timber and ceramic tile substrates. Typical applications Fill holes in wood: knotholes, nail and screw holes, dents, edge build-ups Wall patching: cracks and cavities in plasterboard and cement sheet Furniture repair: tighten loose joints, reset fasteners, rebuild profiles Floor levelling: ramp or smooth minor level variations before floor coverings Trim and fixtures: refit loose door bumpers and trims with reliable hold Architectural & hobby moulding: casting and shaping durable components Why choose Agnews Agnews Water Putty cures to a dense, stone-hard finish that resists shrinkage and cracking even in deep fills. It bonds securely, stays put, and finishes cleanly, delivering a stable base for sanding, priming and painting. From small touch-ups to larger restorations, it provides consistent, professional results. Directions (general guide) Surface prep: Ensure the area is clean, dry, sound and free of dust, oil or loose material. For very porous substrates, lightly dampen to reduce rapid suction. Mix: Add powder to clean water and blend to a smooth, lump-free paste. Adjust water to suit application (thicker for filling, looser for fairing/skim). Apply: Press firmly into cracks or voids with a putty knife or trowel. Overfill slightly so you can sand back flush. Cure: Allow to dry thoroughly. Dry time varies with thickness, temperature and humidity. Finish: Sand to profile. Prime and paint or seal. For exterior applications, always seal after full dry. Exterior use guidance This is a hard-setting, non-flexible compound. For exterior use, only apply over stable substrates with minimal expansion and contraction from temperature changes. Ensure the putty is fully dry before sealing with a suitable exterior-grade coating. Finishing & compatibility Paintable and sealable after full dry; prime as required for best results. Can be cut, carved, drilled and sanded after cure without crumbling. For stained timber finishes, test a small area first for colour and absorption. Pro tips Mix small batches and use promptly. For deep voids, apply in layers if needed, allowing each layer to firm before the next. Store powder in a cool, dry place to maintain its unlimited shelf life. Clean tools with water before material cures. At a glance Substrates: plasterboard, concrete, wood/timber, cement sheet, masonry Uses: patching, levelling, rebuilding, moulding Properties: non cracking, non shrinking, non sinking, non flammable, no VOCs Finish: hard, dense, smooth and paint-ready after sanding/priming
$8.77 - $86.00
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$28.21
Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance. Features & Benefits Marine-grade polyurethane formula with superior adhesion Excellent weathering and saltwater resistance Elastic and vibration-resistant for long-lasting seals Low odour and non-corrosive composition Can be sanded and overpainted after curing Maintains flexibility across wide temperature ranges Where to Use Sealing and bonding on boats, yachts, and marine structures Deck fittings, hatches, and hardware installations Elastic, vibration-resistant joints above and below deck Bonding wood, metals, primers, coatings, ceramics, and GRP plastics Important Notes Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate Surfaces must be clean, dry, and free from grease or dust before application Recommended application temperature: 5°C to 40°C Technical Details Chemical Base 1-component polyurethane Colour Black Cure Mechanism Moisture-curing Density (uncured) Approx. 1.3 kg/L Shore A Hardness 40 Tensile Strength 1.8 MPa Elongation at Break 500% Temperature Resistance -50°C to +90°C (up to 180°C short term) Skin Time Approx. 60 minutes Shelf Life 12 months (stored below 25°C) Packaging 150 mL Tube For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.
$20.52 $0.14/ml
For best performance, pair with these Loxeal products: Loxeal Cleaner 10 Degreaser: clean and degrease the threads first for maximum bond strength. Loxeal Activator 11: speeds curing on stainless steel, plated and other passive metals, in cold conditions, or across larger gaps. Loxeal 58-11 Anaerobic Thread Sealant Loxeal 58-11 is a high performance anaerobic sealant designed for metal thread joints only. It replaces PTFE tape and cord, delivers instant sealing against moderate pressure, and cures to form a shock and vibration resistant seal that remains reliable from -55°C to +150°C. Why choose Loxeal 58-11 Instant sealing against moderate pressure to get systems back in service fast. Thixotropic formulation stays where you put it and resists migration on threads. Wide chemical compatibility including gas, water, LPG, hydrocarbons, oils and more. Shock and vibration resistant for durable, leak free joints. Temperature range from -55°C to +150°C for tough Australian conditions. Certified and approved Gas approvals: DVGW and DIN EN 751-1, plus Australian Gas Association for working pressure up to 20 bar. Oxygen service: Approved for gaseous oxygen up to 10 bar at +60°C. Potable water: WRAS listed and suitable for contact with wholesome water. Also approved for contact with drinking water by Global Mark. Food area use: NSF registered category S4 for use as an adhesive in and around food processing areas. Hydrogen: Tested by KIWA as a sealant for use with pure hydrogen to EN 751-1. Typical applications Sealing tapered and parallel metal threaded fittings in plumbing, HVAC, gas and hydraulic systems. Replacing PTFE tape or thread cord on metal pipework where a permanent, pressure resistant seal is needed. Directions Clean and degrease threads thoroughly. Cut the nozzle to the required bead size. Apply a continuous bead 1 to 2 threads back from the leading edge. Ensure full coverage around the circumference. Assemble and tighten the joint. Wipe away excess uncured material. Allow to cure (see Cure times). Cure speed can be accelerated on passive metals or at low temperature with an appropriate activator. Cure times at +25°C Handling: 15 to 30 minutes Functional: 1 to 3 hours Time to water service for potable water systems at +21.1°C Brass, copper, cast iron: 24 hours Stainless steel, aluminium: 7 days Technical data Chemistry Anaerobic methacrylate Colour Yellow (fluorescent under blue light) Viscosity at +25°C 20,000 to 80,000 mPa·s, thixotropic Specific gravity Approx. 1.1 g/ml Gap filling Up to 0.30 mm (M56 / 2 inch) Flash point Greater than +100°C Shear strength 6 to 13 N/mm² (ISO 10123) Breakaway torque 18 to 24 N·m (ISO 10964) Prevailing torque 7 to 14 N·m (ISO 10964) Service temperature -55°C to +150°C Shelf life 1 year in unopened packaging at ? +25°C Chemical resistance Excellent resistance to motor oil, gearbox oil, gasoline and hydraulic oil. Excellent to good resistance in 50 percent water glycol at elevated temperature. Limitations and notes For metal to metal threaded joints only. Not suitable for plastic threads or rubber components. Liquid product can attack some coatings and plastics. Pre test if unsure. For disassembly, use normal tools. Heat components to approximately +150°C to +250°C if required, then remove cured residue mechanically and clean with solvent. Store in a cool, dry place at or below +25°C. Do not return unused product to the bottle. All technical information is provided as a guide only. Always verify suitability with your specific materials, operating pressures and local regulations before use. Follow all safety and handling instructions on the product label and safety data sheet.
$49.95
Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$20.18 $0.03/g
Premium one component room temperature vulcanising silicone sealant USE Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass CHARACTERISTICS AND ADVANTAGES High temperature resistance (-50 to 250OC) Excellent adhesion Gap filling properties Heat proof Vibration resistant Highly versatile PACKAGING: 300 ml cartridges COLOUR: Black SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking. Uses Fridge and freezer sealing Pizza oven sealing Oven sealing Aluminium Glass Characteristics / Advantages High temperature resistance (-50 - 250°C) Excellent adhesion Heat proof Gap Filling properties Vibration resistant Highly versatile Product Data Colour Black Packaging 300ml Cartridge, 12 cartridges per box Storage 18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Technical Data Chemical Base 1-C silicone Density (uncured) 1.0 kg/l approx. Skin Time 10 min approx. Tack-free time 20 min approx. Curing Time 24 hours approx. Cure Mechanism Moisture-curing Cure Type Acetoxy Application temperature 5 - 45°C Mechanical/Physical Properties Tensile Strength 1.0 N/mm2 approx. Shore a Hardness 25 approx. Ultimate Elongation 600% approx. Application Details Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly. Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. Application Conditions/ Limitations Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
$25.08
![Selleys Marine Flex For Boats Pools and Spas Water Proof [White]](http://gluesaustralia.com.au/cdn/shop/files/091876a6025d44ea89c711822b3ea3d8.jpg?v=1757752868&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$31.24
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
$16.24
PC-Marine™ Epoxy Putty Stick is a specially formulated epoxy putty suitable for wet or underwater applications. Incredibly it has an extended open time (20 – 30 minutes) but cures hard within 60 minutes for a fast return to service and emergency repairs. It sticks great to metals, fibreglass, tile, wood and some plastics such as ABS and rigid PVC. Here are just a few specific uses (there are hundreds of other uses): Seal holes and waterproof fittings Shape and form missing corners or holes in ceramic or fibreglass fixtures Re-attach and secure loose hardware Fill cracks and dings in fibreglass Seal leaks in water tanks How to prepare a surface for bonding with PC-Marine™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Marine™ application Wear disposable gloves to minimize contact with the skin. Use denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner to cleanup before PC-Marine cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying paint remover or paint stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-Marine™ be applied underwater? Yes, application underwater is possible. PC-Marine™ will adhere and cure underwater. However, it is preferable to apply it in dry conditions. Is PC-Marine™ suitable for repairing canoes? PC-Marine™ is excellent for repairs to aluminium and fibreglass canoes but not when they are made with Hypalon. How much time does it take for PC-Marine™ to cure? PC-Marine™ has an extended application or open time of 20 minutes. Most repairs made with PC-Marine™ can be returned to service after 60 minutes. Some applications may require a full 24-hour cure. Is PC-Marine™ green? PC-Marine™ Epoxy Putty stick is white on the inside and green on the outside. The green colour disappears when mixed with the white. The result is an off-white colour when it cures. What is the maximum thickness that PC-Marine™ Epoxy Putty can be applied? PC-Marine™ can be applied thick or thin. There isn’t a thickness limit. It cures from the within via a chemical reaction. It does not need to dry or be exposed to air. How much PC-Marine™ can be mixed at a single time? PC-Marine™ is slower curing than other epoxy putties allowing larger portions to be mixed at one time. Small quantities can be mixed more thoroughly and with less effort. Can PC-Marine™ cure in a freezer? PC-Marine™ is not recommended for sub-freezing temperatures. We recommend an application temperature of 2°C or higher. Does PC-Marine shrink? PC-Marine™ does not shrink.
$16.17
This versatile adhesive is specially formulated for fixing most tile types, offering excellent flexibility and suitability for various surfaces. Key Features: Suitable for most tile types Can be applied over a variety of surfaces Suitable for interior timber (with proper preparation) Highly flexible Tile Types: Ceramic tiles Fully vitrified tiles Mosaics Porcelain tiles Natural stone (excluding moisture-sensitive stone) Suitable Surfaces: Cement render and concrete Fibre-cement sheets Existing ceramic and vinyl tiles Dunlop Undertile Waterproofing Metal surfaces Oil-based painted surfaces Plasterboard Indoor timber (must be adequately prepared) Application Areas: Walls and floors Indoor and outdoor use (as long as there’s no standing water and proper water run-off is ensured) Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.8m²/kg 250 x 250mm and larger 10-12mm 0.5m²/kg
$39.01
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$0.00 - $20.92
Polyfilla F20 Gap Filler: The Ultimate Gap Solution for High-Stress Applications Features Highly Durable High Flexibility Smooth Finish +/- 20% Joint Movement Capability Product Description Polyfilla F20 Gap Filler has been specially formulated to offer superior flexibility in high-stress interior and exterior applications. With up to +/- 20% joint movement capability, this gap filler is ideal for filling gaps around cornices, wall joints, skirting boards, as well as window and door frames. Application This product is extremely easy to use. Simply ensure the area is clean and dry, apply the filler, and allow it to dry. It adheres well to multiple surfaces and offers long-lasting results. Use Cases Cornices Wall Joints Skirting Boards Window & Door Frames
$8.69
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
$21.95
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days. Features Stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries clear Very strong and durable bonding High water resistance (suitable for tiles around pools, but not below the water line for that use Selleys Knead It Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat resistant Clamping recommended for stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but is regained when temperature drops Appearance Translucent Where Can This Product Be Used? Load-bearing repairs Gluing the head back on a hammer Fixing loose table or chair legs Bonding aluminium sheeting Bonding timber on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets Repairing skis Fixing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastics (except Polyethylene and Polypropylene) Crystal Leather How to Use Ensure all surfaces are clean, dry, and free from grease, rust, or paint. For best results, roughen smooth surfaces after solvent cleaning. Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly. Apply adhesive immediately to both surfaces and press together. Clamp the bond for 6–8 hours while setting. Scrape off excess adhesive and clean utensils immediately. Handy Tips Mix in small quantities for longer working time — large mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing. Ensure caps are placed on the correct tubes (they are colour-coded). Remove uncured adhesive with acetone or nail polish remover. Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product. To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully. For cleaning surfaces before use: Porous surfaces use Selleys Liquid Sugar Soap Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits For stubborn residue use Selleys Kwik Strip Smart Ensure the surface is dry before applying. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of eye contact, flush with water for 15 minutes and seek medical attention. Non-toxic when set. Refer to the Material Safety Data Sheet (MSDS) for more information. Storage & Reuse Replace caps tightly after use. Store in a cool, dry place.
$24.50
Seal, reinforce, and finish Foilboard panel joins with this bright silver insulation tape. It creates a clean, professional finish while helping maintain a continuous moisture and air barrier across your installation. Key Features Strong adhesive for secure bonds on Foilboard and reflective insulation surfaces Aluminium foil backing for a neat, reflective finish Helps maintain vapor barrier continuity at seams and penetrations Conformable backing that sits flat on corners and edges Low residue when removed from clean, sound surfaces Suitable for indoor and sheltered outdoor applications Best For Joining Foilboard insulation panel seams Sealing butt joints, corners, and cut edges Patching minor nicks in foil facing General purpose foil tape tasks around HVAC plenums and reflective barriers How To Use Ensure surfaces are clean, dry, and free from dust or release agents. Position panels with tight, aligned seams. Apply tape centered over the joint with at least 12 mm coverage on each side. Press down firmly with a squeegee or cloth to remove air and ensure full contact. Overlap tape ends by at least 25 mm for continuous sealing. Specifications Backing Aluminium foil, silver finish Adhesive High tack pressure sensitive Width 48 mm Length 50 m Application Temperature Apply to clean, dry surfaces above 10°C for best results Colour Silver Tips For Best Results Wipe seams with a clean cloth to remove dust before taping. Use firm pressure along the full tape width to activate the adhesive. Store the roll in a cool, dry place and keep the edge protected from debris. Frequently Asked Questions Can I use this on non foil surfacesIt bonds best to foil faced insulation, reflective barriers, and other clean, non porous surfaces. For porous substrates, prime or seal first. Is it suitable outdoorsSuitable for indoor and sheltered outdoor areas. For direct weather or UV exposure choose a tape designed for full exterior exposure.
$22.79 $18.18
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$18.48
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$9.70
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$25.54
Selleys All Clear Crystal: The Ultimate Multipurpose Sealant Key Features Works on wet, oily, and dirty surfaces Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Best For Metal, Timber, Glass, Glazed tiles, Brick, Stone, and many plastics (may damage polystyrene and polycarbonate). Applications Sky lights Window frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' entries Shower screens Sinks and basins Caravans and recreational vehicles How to Use Use only in a well-ventilated area. Ensure surface is clean and dry. Apply with a caulking gun and smooth with a tool dipped in turps. Limitations May damage some plastics Not for permanent water immersion Not suitable for use over silicones or polystyrene foam Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by cutting and scraping. Technology & Cure Time Solvent-based, with a full cure time of 48-72 hours. For both interior and exterior use.
$21.37
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$7.50
Meet your go to epoxy putty for fast, permanent style repairs. Gorilla All Purpose Epoxy Stick is a hand mixable putty that sets in about 10 minutes and cures in 24 hours to a tough, machinable finish. Once cured it can be drilled, sanded, and painted. It is waterproof, non rusting, and ready for indoor or outdoor jobs around the home, car, boat, and garden. Why you will like it Fast setting. Approximate set time 10 minutes. Paintable after about 1 hour. Full cure in about 24 hours for a hard wearing repair. Works on most common materials including metal, PVC, many rigid plastics, wood, stone, ceramic, brick, concrete, fiberglass, and glass. Non rusting formulation for durable repairs in wet or humid areas. Waterproof when cured. Suitable for indoor and outdoor use. NSF ANSI 61 certified drinking water safe for contact with potable water once cured. Great for Plumbing repairs such as sealing low pressure leaks and patching drainage pipes Automotive trims and general panels that do not exceed service temperature of typical epoxy repairs Household fixes like filling holes, anchoring hardware, rebuilding small parts, and edge repairs DIY and craft projects that need a sculptable, sandable fill Important use notes Not for exhaust systems. For plumbing, use for temporary repair of drainage pipes or low pressure pipes only. Turn water off, apply, then wait at least 1 hour before turning water back on. Bonded wood should not be submerged or soaked after repair. How to use Wear disposable gloves. Work in a well ventilated area. Prepare the surface. Clean off dust, oil, and loose material. Roughen smooth surfaces with sandpaper. Cut the amount you need. Remove the film wrapper and foil sticker. Reseal unused putty to limit air exposure. Knead for 30 to 60 seconds until the colour is uniform. Mix thoroughly or it will not harden completely. Apply within 5 minutes of mixing. Press firmly into place. Smooth with wet gloved fingers if a smooth finish is desired. Remove any squeeze out before hardening. Allow to set about 10 minutes. Paint after about 1 hour. Full cure about 24 hours. Specifications Format Hand mixable epoxy putty stick Size 56.7 g Set time About 10 minutes Paintable After about 1 hour Full cure About 24 hours Indoor or outdoor Yes, waterproof when cured Drill, sand, paint after cure Yes Drinking water contact NSF ANSI 61 certified drinking water safe once cured Clean up and storage While uncured, wipe away with soap and water, acetone, or isopropyl alcohol. For cured material, remove by sanding, scraping, or chiseling. Store the stick in its vial with film and foil sticker re applied. Keep sealed in a cool, dry place. Keep away from children and animals. Safety Wear gloves during mixing and application. Avoid contact with skin and eyes. If in eyes rinse with water for 15 minutes. If on skin wash with soap and water. Use in a well ventilated area. For medical emergencies in Australia call 000.
$37.90
Selleys Roof & Gutter Silicone is a premium neutral-cure silicone sealant engineered for the demanding conditions of Australian roofing and guttering. Colour-matched in Cottage Green to blend seamlessly with Colorbond and tiled roofs, it delivers a durable, weatherproof seal that flexes with the structure and stands up to harsh sun, rain, and temperature swings. Key Features Neutral cure formula safe to use on most metals, including Colorbond and galvanised steel, without causing corrosion Colour-matched Cottage Green for a clean, near-invisible finish on matching roofs and gutters Excellent weather and UV resistance for long-lasting performance outdoors Permanently flexible to absorb building movement, expansion, and vibration without cracking Strong adhesion to metal, masonry, concrete, glass, and most common building materials Fully waterproof seal that resists leaks and water seepage 300g cartridge suited to standard caulking guns for fast, controlled application Typical Uses Sealing joints and laps in roofing and guttering Capping and flashing seals Downpipes, ridge capping, and valley gutters General weatherproofing and gap sealing around the home and on the job site How to Use Surfaces should be clean, dry, and free of dust, grease, and loose material. Cut the nozzle to the desired bead size, load into a caulking gun, and apply an even bead to the joint. Tool off the surface within a few minutes for a smooth finish. Allow to fully cure before exposing to water.
$25.40
Seal leaks fast and protect exposed joins with Grunt Flashing Tape. This heavy duty self adhesive tape conforms to uneven surfaces, creates a long lasting waterproof barrier, and is ideal for quick fixes and preventative maintenance across roofs, gutters, and outdoor fixtures. Why choose this tape Weatherproof seal that helps stop water ingress at laps, seams, and penetrations. Strong tack for reliable adhesion on metal, plastic, and painted surfaces. Flexible backing that moulds to contours, ridges, and fasteners. UV and outdoor ready for Australian conditions. Clean finish suitable for temporary and permanent repairs. Common uses Sealing gutter joins, end caps, and mitres Flashing around skylights, flues, and vents Stopping drips at roof sheet overlaps Repairing small cracks in downpipes and rainwater fittings Protecting fasteners and exposed fixings from water General waterproofing on caravans, sheds, pergolas, and trailers Surface compatibility Works on most clean, dry, and sound substrates including coated metal roofing, painted timber, rigid plastics, fibreglass, and masonry that has been sealed. Not recommended for silicone contaminated surfaces or areas that remain permanently submerged. How to apply Prepare the area. Remove dust, old flaking coatings, oil, and loose rust. Dry the surface thoroughly. Measure and cut the tape to length with a knife or scissors. Peel and stick. Remove the release liner as you apply, pressing the tape down firmly. Roll with a hand roller or the back of a cloth to eliminate air pockets and ensure full contact. Overlap adjoining pieces by at least 25 mm for a continuous seal. Finish edges with extra pressure. Avoid applying in rain or onto wet surfaces. Pro tips For porous substrates, prime with a suitable primer and allow to dry before taping. Cold weather can reduce tack. Warm the tape and surface slightly to improve bond. Ensure water can shed over the tape rather than against the lap direction. Specifications Brand Grunt Product type Self adhesive flashing and sealing tape Size 50 mm width x 10 m length Use Exterior and interior repairs, roofs, gutters, and general waterproofing Application temperature Apply in dry conditions on clean and sound surfaces Cleanup Wipe tools with mineral turpentine or adhesive remover as suitable for the substrate Frequently asked questions Can I paint over itYes, most solvent based and acrylic paints will adhere. Test a small area first. Is it suitable for potable waterNot intended for potable water contact. Will it work on damp surfacesBest results are achieved on dry surfaces. Dry the area before application.
$15.20 $12.25
Aftek MDF Adhesive 250 ml Overview Aftek MDF Adhesive 250 ml is a high quality fast setting MDF adhesive set designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials MDF timber trims decorative profiles Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Use in ventilated areas between 10°C and 30°C. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Activator accelerates set in seconds to minutes. Full strength develops over several hours. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Remove overspray and uncured adhesive with suitable solvent. Use carefully to avoid staining. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$12.53
High strength, water based adhesive for carpet and cork Dunlop Multipurpose Carpet & Cork Adhesive is a water based, high strength adhesive designed for installing smooth or textured backed carpets and cork tiles. It delivers excellent wet grab and reliable bond on prepared subfloors. Suitable Surfaces Concrete Marine plywood Fibre cement sheet Key Features Water based and low odour High initial grab for reduced slippage Repositioning window up to 60 minutes Install immediately into wet adhesive for most carpets For cork or stiff backings, allow 10 to 15 minutes tack time before laying Coverage Approx. 2.5 m² per litre with a 3.2 mm V notch trowel Approx. 3.5 m² per litre with a 2.4 mm V notch trowel Application Ensure subfloor is dry, smooth, clean and protected from moisture. Prime highly porous concrete or timber before applying. Spread an even coat with the recommended V notch trowel. Lay carpet into the wet film. For cork or stiff backings, wait until the adhesive becomes tacky. Roll in both directions with a suitable drum roller to ensure full transfer. Set and Traffic Times No foot traffic for 24 hours Heavy traffic after 48 hours Avoid water and cleaning for 48 hours Clean Up Clean tools immediately with warm soapy water Remove dried residue with mineral turps Storage Shelf life up to 12 months in an unopened container stored at around 23°C. Good To Know Apply between 10°C and 30°C. Coverage varies with subfloor condition and trowel technique.
$54.95
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$12.75
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$24.20
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
SIKASIL® -670 FIRE | JOINT SEALANT Fire-rated joint sealant Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Easy to smooth and very good workability DESCRIPTION Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant. USES Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. CHARACTERISTICS / ADVANTAGES ▪ Up to 4 hours fire resistance according to EN 1366-4 ▪ Very good resistance to weathering ▪ Movement capability of ± 35% (ASTM C 719) ▪ Easy to smooth and very good workability ▪ Good adhesion to many different substrates ▪ Neutral curing ENVIRONMENTAL INFORMATION ▪ LEED® EQc 4.1 ▪ SCAQMD, Rule 1168 ▪ BAAQMD, Reg. 8, Rule 51 APPROVALS / STANDARDS ▪ EN 15651-1 F EXT-INT CC 25 LM ▪ EN 15651-4 PW INT ▪ ISO 11600 F 25 LM & G 25 LM ▪ ASTM C 920, class 35 ▪ EN 1366-4 assessment report ▪ ETAG 026 assessment report ▪ EN 13501-2 classification report ▪ EN 140-3 ▪ EN 13501-1 class B-s2-d0 PRODUCT INFORMATION Chemical Base Neutral cure silicone Colour: Grey Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C. Density 1.35 kg/l approx. (ISO 1183-1) TECHNICAL INFORMATION Shore A Hardness 16 approx. (after 28 days) (ISO 868) Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339) 0.50 N/mm2 approx. at 100% elongation (−20 °C) Elongation at Break 650% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719) Service Temperature −40 °C to +150 °C Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below). Backing Material Use polyethylene foam backing rods. Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390) Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature Substrate Temperature +5 °C to +40 °C Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2) Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1) Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2) APPLICATION INSTRUCTIONS SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without primers and/or activators APPLICATION METHOD / TOOLS Sikasil®-670 Fire is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically. FURTHER DOCUMENTS ▪ Safety Data Sheet (SDS) ▪ EN 13501-2 classification report ▪ ETAG 026 assessment report ▪ Brochure Sika Fire Protection Solutions LIMITATIONS ▪ Sikasil®-670 Fire cannot be overpainted. Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product. ▪ Do not use Sikasil®-670 Fire on natural stone. Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant. ▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools. ▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion. ▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.
$22.15
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$8.50
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$20.99
PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. - Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.
$16.17
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$22.66
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600356N_25b0d34f-62b0-49f4-86cb-a6535eeabdae.jpg?v=1754712481&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$27.91
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$29.36
Gorilla Black Mounting Tape delivers a fast, permanent bond for indoor projects. This industrial strength double sided tape grips to a wide range of smooth and lightly textured surfaces, helping you mount, fix, and build without screws or nails. Why you will love it Strong indoor hold with permanent bond Double sided for clean, hidden mounting Works on smooth and lightly textured surfaces Easy, tool free application Weather resistant carrier helps resist moisture and temperature changes indoors Great for Mounting hooks, signs, cable clips, and décor Fixing skirting trims and craft fixtures Securing powerboards and small organisers to walls or furniture DIY quick fixes where drilling is not an option Works on Metal, glass, finished wood, plastic, tiles, painted drywall, stone, and more. Not recommended on delicate, recently painted, dusty, oily, or damp surfaces. How to use Clean surfaces with isopropyl alcohol and let dry. Measure and cut the length you need. Press tape firmly onto the back of the object. Peel liner to expose the adhesive. Position once and press firmly for 30 to 60 seconds to activate the bond. Load gradually. Full bond strength develops after proper pressure and dwell time. Pro tips Use enough tape to support the weight of the item. As a guide, allow generous coverage across the mounting area. For painted surfaces, test in a small area first. Removal may damage paint. Avoid repositioning after contact. This reduces bond strength. Specifications Brand Gorilla Product type Double sided mounting tape Colour Black Length 3.04 m Use Indoor Bond Permanent Care and safety Keep out of reach of children. Do not use as a load bearing safety device. Store in a cool, dry place with liner intact.
$36.07 $27.45
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$19.50
Crommelin Hybrid MS Polyurethane Flexible Sealant 300ml Take on interior and exterior sealing with a professional grade hybrid MS polyurethane. This single component sealant delivers a flexible, durable seal on common building substrates and is suitable for a wide range of construction and maintenance tasks. Key benefits Very low VOC and isocyanate free UV resistant for long term outdoor performance High flexibility to accommodate joint movement Excellent adhesion on properly prepared porous and non porous surfaces Easy to gun, tool and clean up Typical applications Construction and expansion joints Perimeter sealing around windows and doors Roofing and cladding laps, flashings and penetrations General gap sealing in wet and dry areas Suitable substrates Concrete, masonry, brick and render Timber and fibre cement Metals and coated metals Many plastics* and glass *Always pre test for compatibility and adhesion. Surface preparation Surfaces must be clean, dry, sound and free of dust, oil, release agents and loose material. Remove old sealant and contaminants. Abrade dense or glossy surfaces if required. Use suitable primer if specified for difficult or highly porous substrates. Mask edges for neat joints and install closed cell backing rod where needed to control joint depth. Application Cut nozzle to required bead size and load cartridge into a quality caulking gun. Gun a continuous bead into the joint ensuring full contact with sides and backing. Tool off with a moistened spatula for a smooth finish before skin forms. Protect from water and disturbance during initial cure. Clean up Clean tools and fresh spills promptly. Once cured, remove by mechanical means. Good to know Low odour formulation suitable for indoor use with ventilation. Paintable with many water based coatings once skinned and cured. Always test first. Store upright in a cool, dry place. Keep out of direct sunlight. Safety Wear suitable gloves and eye protection. Avoid contact with skin and eyes. If contact occurs, rinse with clean water. Refer to the product Safety Data Sheet for full precautions. What’s in the box 1 x 300ml cartridge 1 x application nozzle
$15.15
Fast, reliable bond for vinyl sheet and tiles Dunlop Vinyl Adhesive is a water based, high strength adhesive that spreads easily and delivers dependable bonds for vinyl sheet and vinyl tile on most concrete and timber subfloors. Ideal for installers and serious DIYers who want clean application and solid performance. Key features High initial grab for confident placement Easy to spread with smooth, low odour application Suitable for vinyl sheet and vinyl tile on concrete and timber subfloors Approximate coverage: 4 to 5 m² per litre, depending on surface and technique Tack time: 5 to 15 minutes at 23°C and 50% RH Sets in 24 hours for light foot traffic and finishing Where to use Interior installations of vinyl sheet and vinyl tile Most prepared concrete and timber subfloors Surface preparation Ensure surfaces are dry, smooth, clean and free of dust, oil, paint or contaminants that could limit adhesion. Prime highly porous concrete or timber with a suitable primer as directed by the manufacturer. Level or repair imperfections with a compatible floor leveller or floor repair compound before bonding. Application Apply an even coat to the subfloor using a 1.6 × 1.6 × 1.6 mm V notched trowel. Allow adhesive to become tacky before laying vinyl. Typical tack time is about 10 minutes, longer in cool conditions and shorter in warm conditions. Do not allow a skin to form. Lay the vinyl into the adhesive. Roll firmly in both directions to ensure full transfer to the back of the vinyl. Clean up Clean tools and spills immediately with warm soapy water. Remove dried adhesive with mineral turps. Conditions and storage Apply between 8°C and 35°C with adequate ventilation. Shelf life: 12 months in unopened container stored at approximately 20°C. Good to know Use a roller after placement to improve bond and minimise bubbles. Coverage varies with subfloor condition, porosity and trowel technique. Warranty Product is guaranteed for 10 years when installed in accordance with the manufacturer’s instructions.
$27.85
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$35.34 - $39.95
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$5.75
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects. Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions. T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger. Key Features: All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications. Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in. Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold. Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan. Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox. Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability. Usage Applications: Home repairs, including fixing broken items and sealing leaks. Crafting and DIY projects, offering creative flexibility. Outdoor applications, including camping gear repairs. Professional job site tasks, providing reliability and strength. Why Choose T-Rex® Tape? When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project. In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
$16.48
You have seen 48 out of 498 products
Professional-level performance for strength, durability and productivity on site. Expect defined movement capability, temperature/chemical ratings and precise application methods. Use filters to refine by chemistry and pot life. Always review the product page and TDS/SDS.
