Selleys Roof & Gutter Silicone is a premium neutral-cure silicone sealant engineered for the demanding conditions of Australian roofing and guttering. Colour-matched in Cottage Green to blend seamlessly with Colorbond and tiled roofs, it delivers a durable, weatherproof seal that flexes with the structure and stands up to harsh sun, rain, and temperature swings. Key Features Neutral cure formula safe to use on most metals, including Colorbond and galvanised steel, without causing corrosion Colour-matched Cottage Green for a clean, near-invisible finish on matching roofs and gutters Excellent weather and UV resistance for long-lasting performance outdoors Permanently flexible to absorb building movement, expansion, and vibration without cracking Strong adhesion to metal, masonry, concrete, glass, and most common building materials Fully waterproof seal that resists leaks and water seepage 300g cartridge suited to standard caulking guns for fast, controlled application Typical Uses Sealing joints and laps in roofing and guttering Capping and flashing seals Downpipes, ridge capping, and valley gutters General weatherproofing and gap sealing around the home and on the job site How to Use Surfaces should be clean, dry, and free of dust, grease, and loose material. Cut the nozzle to the desired bead size, load into a caulking gun, and apply an even bead to the joint. Tool off the surface within a few minutes for a smooth finish. Allow to fully cure before exposing to water.
$19.90
Strengthen critical junctions and stop leaks before they start. Crommelin Waterproofing Tape is a flexible, self-adhesive reinforcing tape designed to bridge cracks, joints, and movement-prone areas so your waterproofing membranes and sealants perform at their best. Why you will like it Reinforces weak points at wall to floor junctions, around drains, over hairline cracks, and along internal corners. Excellent adhesion to common building surfaces when used with compatible primers and membranes. Flexible backing conforms to corners and curves to maintain a continuous seal. Moisture barrier assist helps reduce the risk of water ingress beneath tiles and finishes. Easy to cut and apply for fast prep on bathrooms, balconies, laundries, and wet areas. Ideal for Showers, bathrooms, and laundries Balconies and terraces before tiling Planter boxes and upstands Penetrations such as pipes and wastes Internal corners, junctions, and small static cracks Quick specs Product Waterproofing reinforcement tape Length 5 m Finish Flexible tape for embedment into compatible membranes Typical surfaces Concrete, rendered masonry, fibre cement, primed timber, sealed gypsum, existing compatible membranes Application Hand applied, press firmly with roller or trowel How to use Prepare the area. Surface must be clean, dry, sound, and free of dust, oils, and loose material. Prime as required by your chosen waterproofing membrane system. Measure and cut lengths to suit corners, junctions, and penetrations. Pre fit to check placement. Bed the tape into the first wet coat of compatible membrane or approved adhesive. Press firmly to remove air pockets and ensure full contact. Overlap joins by at least 50 mm. At corners, mitre or fold neatly so the tape remains flat without creases that could trap water. Topcoat with additional coats of membrane to fully encapsulate the tape, observing required dry times between coats. Cure the membrane system as directed before tiling or finishing. Good to know Cover the tape with a compatible liquid membrane. Do not leave exposed to prolonged UV. Always follow the membrane manufacturer instructions for primers, coat thickness, and cure times. If in doubt about compatibility, perform a small adhesion test on your substrate and membrane. Storage and safety Store in a cool, dry place away from direct sunlight. Wear gloves and eye protection during surface prep and membrane application. Dispose of offcuts and packaging according to local regulations. What is in the box 1 roll Crommelin Waterproofing Tape, 5 m length Glues Australia helps Australians fix and protect with confidence. If you need help choosing a compatible membrane or primer for this tape, contact our team.
$39.15 $30.48
Stop leaks fast with Fastfix Waterproof Repair Tape. This heavy duty, self-sealing tape forms a tough barrier that helps block water, air and moisture on a wide range of materials. Keep a roll in the toolbox, the ute or the caravan for quick fixes at home or on site. Creates a waterproof seal on clean, dry surfaces Extra thick backing with strong adhesive for a reliable hold Sticks to PVC, metals, plastics, rubber, vinyl, glass, ceramics and more Great for gutters, downpipes, garden hoses, pool gear, tents and tarps Easy to apply by hand with no special tools required Suitable for indoor and outdoor use Where it works Gutters and roof flashings Downpipes and irrigation fittings Garden hoses and pool hoses Camping gear such as tents and tarps Boat covers and awnings Plastic bins, storage tubs and general repairs How to use Clean and dry the area. Remove dust, oil and loose paint. Cut a piece of tape that overlaps the repair by at least 25 mm on all sides. Peel the liner and position the tape carefully. Avoid touching the adhesive. Press down firmly from the centre out to the edges to remove air bubbles. For higher pressure or larger repairs, apply a second layer with the seam offset. Allow time under firm pressure to achieve the best bond. Good to know Best adhesion on smooth, non-porous surfaces. Not a substitute for structural repairs. For wet or submerged applications, bond strength can vary depending on surface and water pressure. Test on a small area first if surface is delicate or freshly painted. Specifications Brand Fastfix Product type Waterproof repair tape Size 50 mm width x 5 m length Colour Black Adhesive Pressure-sensitive Finish Flexible, conformable backing Suitable environments Indoor and outdoor Storage Store cool and dry, out of direct sunlight. Keep liner on until use.
$21.52 $18.69
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Household and workshop repairs that need speed and strength Fixing fixtures, brackets, and hardware Filling chips and rebuilding small edges before sanding Suitable surfaces The adhesive works well on the following surface types when properly prepared: Metal hardware Ceramic tiles Most rigid plastics except polyethylene and polypropylene Timber and MDF Stone and concrete Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure. Temperature and environmental performance Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$13.14
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$13.00
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.
$22.79
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. Features Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other. FEATURES: Waterproof backing enhanced with R-Flex Technology™ for greater durability Can be used underwater UV resistant All-weather: withstands temperatures from -56C to 93C. WATERPROOF ADHESION Extra thick butyl-based adhesive means durable repairs, even under water. R-FLEX TECHNOLOGY Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C. Durable, flexible and UV resistant backing for long lasting repairs. ALL WEATHER Waterproof and built to withstand extreme temperatures from -56C to 93C.
$32.95
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1004_b7e3fa7f-b596-4427-b05e-1d6d905aafa9.jpg?v=1754716362&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Grey x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_5bffff98-306e-4768-8b68-890bdca140bb.png?v=1754716362&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$12.29
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$15.39
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer. The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time. Where can this product be used? Showers screens Baths Spas Sinks Plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Clean surface with mineral turpentine and dry. Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun. Apply with steady pressure, ensuring sealant is pushed into joint. Tool with a spatula dipped in detergent water within 5-10 mins of application. Clean up with mineral turpentine before product skins. Sealant will cure in 72hrs. Limitations: Not paintable. Complete painting 7 days prior to applying sealant. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. Not suitable for aquariums. Not suitable for food or drinking water contact. Not suitable for permanent water immersion. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. *Warranty Information Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$13.62
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.60
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected. Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects. N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like. Uses N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels. It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials. Technical Features Non-hardening – remains permanently flexible to provide a lasting seal Good adhesion – adheres well to most substrates Moisture resistance – provides an excellent barrier to moisture vapour Microbe resistance – resists microbial attack Low shrinkage – avoids the risk of sealant pulling away from joint surfaces Wide service temperatures – withstands –40oC to +80oC service conditions Application Tips Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem. As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress. Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor. N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel. Technical Details and Performance Indicative information only, not to be used for setting specifications. Colour Off White Specific Gravity 1.4g/mL Consistency Non-sag Slump (MIL-S-8802, @ 32oC ) 2.5mm maximum Viscosity (Brookfield HAF 7/2 @ 25oC ) 10,000 – 14,000 Poise Flash Point 85oC Storage Life (25oC ) Indefinite Packaging Plastic cartridge (410g) Performance Properties Shrinkage (% maximum) 5 Service Temperature –40oC to +80oC Life Expectancy Up to 20 years Clean Up Sealant may be removed with a cloth dampened with kerosene or mineral spirits
$19.11
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$22.00
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$20.69
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.78
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$28.49
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$165.00
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$19.89
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$48.79
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Express Wet Area Tape is a self-adhesive waterproofing joint tape that seals the most leak-prone parts of a wet area, the joints where floor meets wall, and around shower grates and outlets. Simply peel and stick: no messy fillets, no waiting for a bond breaker to cure. Paired with Dunlop Express Wet Area Waterproofing membrane it forms a rapid, complete waterproofing system that lets tiling commence just four hours after the membrane goes on.Where to use itSuitable for indoor and outdoor wet areas including bathrooms, showers, laundries and balconies. It performs over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard.How to useMake sure surfaces are clean, dry and dust-free. Peel the backing and press the tape firmly along floor/wall junctions, corners and around penetrations such as shower grates and outlets. Where two lengths of tape meet, overlap them by a minimum of 15mm. Then apply Dunlop Express Wet Area Waterproofing membrane over the taped joints and the rest of the area as normal.Important notesA standard shower recess with 1.8m high walls needs roughly 7m of tape, so one 10m roll comfortably covers a typical shower. Used with the Express membrane, the system meets Australian Building standards for wet area waterproofing.Specifications Size 80mm x 10m roll Colour Grey Overlap Minimum 15mm at joins Substrates AAC, fibre-cement, concrete, renders, screeds, wet area plasterboard SafetyLow-hazard adhesive tape; use care with cutting tools and follow the safety directions of the waterproofing membrane applied over it.
$65.28
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that delivers an instant waterproof seal across the joints where leaks start: the junction between floor and wall, and around shower grates and outlets in bathrooms, kitchens and laundries. It is the joint-sealing half of the Dunlop Pro Rapid system; team it with Dunlop Pro Rapid Waterproofing Membrane and tiling can commence just four hours after the membrane is applied, with the finished system meeting Australian Building standards for waterproofing.Where to use itDesigned for internal wet areas such as bathrooms, showers, kitchens and laundries. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheets, wet area grade plasterboard, plywood, internal AAC blocks and panels, concrete cured for a minimum of 28 days, and renders and screeds cured for a minimum of 7 days.How to useEnsure the surface is clean, dry and free of dust. Peel the release liner and press the tape firmly into floor/wall junctions, corners and around grates and outlets, smoothing out air bubbles as you go. Then apply Dunlop Pro Rapid Waterproofing Membrane over the tape and the remainder of the area to complete the system.Important notesSubstrate curing times matter: concrete needs at least 28 days and renders or screeds at least 7 days before taping and waterproofing. This tape is intended for internal applications and is designed to work as a system with the Pro Rapid membrane.Specifications Size 75mm x 15m roll System partner Dunlop Pro Rapid Waterproofing Membrane Tile after 4 hours (as part of Pro Rapid system) SafetyLow-hazard self-adhesive product; take care when cutting lengths and follow the safety directions on the membrane used over it.
$98.41
Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.
$43.00
Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.
$313.95
Dunlop Waterproofing Reinforcing Mat is the quiet workhorse of a Dunlop waterproofing job. This 100mm wide fabric roll is embedded into the wet membrane at every corner, joint and crack, the places where movement and stress are most likely to open up a leak. By carrying the membrane across these weak points, it helps guarantee proper film thickness in the critical zones and lets you apply the second waterproofing coat immediately over the reinforced areas.Where to use itUse it indoors in wet areas as an integral part of the Dunlop waterproofing system, together with Dunlop Undertile Waterproofing. Reinforce wall/floor junctions, wall/wall corners, sheet joints, cracks, shower hobs and hob/floor joints, over metal or PVC angles, and along 90-degree external edges such as balcony perimeters.How to useApply the first coat of membrane to the junction, press a length of mat into the wet membrane so it sits flat without air pockets, then coat over the top so the fabric is fully saturated. The mat also acts as a carrier in awkward, hard-to-reach spots and smooths rough joints so the membrane covers evenly. Cut lengths with scissors or a utility knife as you go.Important notesThe junctions between wall and floor, hob and floor, and vertical corners where two walls meet should always be reinforced. The mat is a reinforcing component, not a standalone waterproofing product; it must be fully encapsulated in membrane.Specifications Size 100mm x 50m roll Use with Dunlop Undertile Waterproofing and Dunlop membranes Application areas Junctions, corners, joints, cracks, hobs, edges SafetyLow-hazard fabric product; take care when cutting and follow the safety directions of the membrane being used. A Safety Data Sheet is available from Dunlop Trade.
$67.73
Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.
$142.94
You have seen 96 out of 167 products
Keep water out of joints, seams and enclosures with waterproof and weatherproof products. Match cure type and flexibility to the application (bathroom, kitchen, outdoor). Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
