Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$18.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$12.00
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula. Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm2/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
$13.90
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$13.00
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected. Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects. N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like. Uses N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels. It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials. Technical Features Non-hardening – remains permanently flexible to provide a lasting seal Good adhesion – adheres well to most substrates Moisture resistance – provides an excellent barrier to moisture vapour Microbe resistance – resists microbial attack Low shrinkage – avoids the risk of sealant pulling away from joint surfaces Wide service temperatures – withstands –40oC to +80oC service conditions Application Tips Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem. As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress. Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor. N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel. Technical Details and Performance Indicative information only, not to be used for setting specifications. Colour Off White Specific Gravity 1.4g/mL Consistency Non-sag Slump (MIL-S-8802, @ 32oC ) 2.5mm maximum Viscosity (Brookfield HAF 7/2 @ 25oC ) 10,000 – 14,000 Poise Flash Point 85oC Storage Life (25oC ) Indefinite Packaging Plastic cartridge (410g) Performance Properties Shrinkage (% maximum) 5 Service Temperature –40oC to +80oC Life Expectancy Up to 20 years Clean Up Sealant may be removed with a cloth dampened with kerosene or mineral spirits
$17.00
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$22.00
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$17.00
Selleys Liquid Nails Exterior: The Builder's Choice for Durable Outdoor Bonds Key Features Adheres up to 3 tonnes per m² after just 4 hours on timber Water, heat, and UV-resistant Long-lasting bond that won't crack or go brittle Fast and easy water clean-up Compliant with Australian Standard AS 2329(1999) and Green Building Council VOC limits Suitable Materials This adhesive is ideal for the following materials: Timber Plasterboard MDF LOSP Treated Timber Concrete Masonry Plastics (pre-test for compatibility) Tiles Glass Ceramics Directions for Use Follow these simple steps for optimal performance: Ensure surfaces are clean and free from grease or loose particles. Cut cartridge tip, fit nozzle, and cut to 5mm opening. Apply adhesive along the material's length or in beads on flat surfaces. Press pieces firmly together, securing with fasteners or clamps. Allow to set for a minimum of 4 hours before removing any temporary fasteners. Limitations Not suitable for use on PFTE, PE, or PP. Cleaning & Safety Clean up is easy with warm soapy water or a damp cloth for wet adhesive, and a scraper or sandpaper for dried adhesive. Product Specifications Available in 350g cartridges, in white color, and uses Self-crosslinking acrylic technology.
$12.00
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.00
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$26.00
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/51345fd2ddf64a74a03e2c6b9e0d7e1a.jpg?v=1757753232&width=645)
$16.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/81e21d7d520d41a280976d39a403b5c9.jpg?v=1757753238&width=645)
$16.00
Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$19.00
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$45.65
Selleys 655 FC Crystal Clear Flexible Adhesive and Sealant 290 mL Premium 100 percent crystal clear hybrid adhesive and sealant that delivers superior strength, instant grab, and long lasting flexibility. Bonds and seals on most common building materials, works indoors and outdoors, and can be applied to wet or damp surfaces. Low VOC, non yellowing, paintable, and non slumping for neat vertical and overhead joints up to 20 mm. Why you will love it Superior strength with instant grab Primerless adhesion on most surfaces Applies to wet or damp substrates Fast curing with non slumping finish Crystal clear appearance that stays clear Low VOC and isocyanate free Paintable with water based paints Suitable for interior and exterior use Where it works Ideal for sealing, bonding, and filling on concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, fiberglass, and most plastics. Not recommended for polyethylene, polypropylene, or PTFE. Typical applications Clear sealing of kitchen and laundry splashbacks Bonding trims, panels, and skirtings Sealing gaps in windows, door frames, and cladding General construction and maintenance sealing where a clear finish is desired How to use Prepare the surface so it is clean and free from dust, grease, and loose material. Cut cartridge tip, attach nozzle, and load into a caulking gun. Cut nozzle to the required bead size. Apply a continuous bead, pressing firmly so the product contacts both sides of the joint. Tool with a soapy solution before skinning. For neat edges, mask before applying and remove tape before skin forms. Clean up Uncured product cleans off with mineral turps. Once cured, remove by scraping or sanding. A dedicated silicone and adhesive remover can assist. Good to know Do not paint with solvent based paints. If painting, first coat with a water based paint. Not suitable for permanent water immersion or below water line use. Store below 30°C. Use within 6 months after opening for best results. Specifications Technology Moisture curing silyl modified polymer Colour Clear Pack size 290 mL cartridge Density Approx. 1.06 g/mL Application temperature 5 to 35°C Tooling time at 23°C and 50 percent RH About 25 minutes Skin time at 23°C and 50 percent RH About 45 to 55 minutes Cure rate at 23°C and 50 percent RH Approx. 3 mm per 24 hours Slump 0 mm Tensile strength About 1 MPa Shore A hardness 30 ± 5 Elongation at break Approx. 130 percent Modulus at 100 percent elongation About 1.0 MPa Service temperature 0 to 70°C VOC content Approx. 35 g/L Safety Follow good ventilation and hygiene practices. Refer to the product safety data sheet for detailed advice.
$20.00
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$20.00
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$24.00
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$23.60
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$27.16
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
$16.24
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 30 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter. Here are just a few specific uses (there are hundreds of other uses): Reattach missing swimming pool tiles. Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat. Repair cracked or damage swimming pool or hot tub skimmer. Waterproof and Seal cracked fibreglass. Seal screw holes to hatch lids or seating. Attach fish locators to transom. Repair stock tanks. Repair broken refrigerator door shelf fixtures. Repair broken pottery. Repair shower basin or antique bath tub. Seal leaking air conditioner drip pan. Seal underground conduit. How to prepare a surface for bonding with PC-11® Epoxy Paste Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-11® Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. Can PC-11® be used in Aquariums? There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed. What plastics does PC-11® stick to? PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite. What plastics does PC-11® not stick to? PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate. What rubbers does PC-11® stick to? PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers. What temperatures can PC-11® be applied? PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time. Can gel coat be applied to PC-11®? Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat. Can PC-11® be painted? Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat. Will PC-11® yellow in direct sunlight? Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important. Can PC-11® be thinned with solvent? PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible. PC-11® is a simple one to one mix, but how accurately does the measurement need to be? The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
$18.79
PC-Plumbing™ Epoxy Putty is for pipes. Use PC-Plumbing™ to stop leaks in less than 60 minutes. Pre-measured and easy to use and 2 part epoxy putty does not require tools. Hand mix and apply. NSF® approved for plumbing repairs and for contact with potable water supply pipes. Here are just a few specific uses (there are hundreds of other uses): Seal leaks in copper pipes resulting from hard water Fix freeze damaged PVC and copper pipes Stop leaking copper elbow and tees Fill abandoned drill holes in ductwork Insulate electrical connections from water
$16.17
PC-Concrete ™ Anchoring and Crack Filling Epoxy— is the epoxy chosen to repair cracks in a warehouse and factory floors. Dispense and apply using a standard size caulking gun. Cures hard enough to drive over within 3 hours at standard temperature. Nothing stronger for your anchoring applications. PC-Concrete™ is a two-component (1:1 ratio), 100% solids, high modulus, and structural epoxy paste. PC-Concrete™ is a solvent-free, no odour, high strength, moisture insensitive epoxy system. The resin and hardener are uniformly dispensed from a 9-ounce cartridge system and mixed through a mixing nozzle using a standard size caulking gun. (We recommend at least an 18:1 thrust ratio). PC-Concrete™ is also provided in a 22-ounce dual cartridge system for Contractors and Professionals. This size requires a 600ml high thrust dual cartridge dispensing gun. For filling larger cracks and cavities use the 102-ounce bulk kit. PC- Concrete™ will NOT SHRINK. Suitable for Interior and Exterior applications. Can be applied to WET & UNDERWATER surfaces. Here are just a few specific uses (there are many other uses): Anchor into marine docks above or below waterline Anchor equipment to floors Bond to pre-stressed floors Anchor into stone and rock. Install anchor bolts for sill plates Anchor into foundations and block Fill cracks in concrete allowing equipment traffic In 4 hours Anchor into concrete railroad ties Anchor HVAC equipment to concrete pads and roofs Waterproof floor to wall cracks Re-anchor railing at convention center or apartment building Anchor seats in lecture hall or theaters Repair broken concrete in shopping mall parking garage Fill spalled concrete in car wash Fix fork truck damaged concrete in warehouse Seal crack in sanitation and chemical storage facility containment area Repair floor in fire station garage Anchor safe to floor prison and security pickproof epoxy Anchor machinery
$14.46
![Parfix Roof Gutter Concrete Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697115751_115bf094-7ace-4242-bb30-259319ee7c44.png?v=1754712242&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a grey, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$10.27
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$11.49
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.03
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.14
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
![Monarch Mini Silicone Mould Resistant [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029066_2af7d350-636b-476c-9c8a-71b4ddb4f0e5.png?v=1754712301&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.30
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$7.22
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services. With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand. FEATURES Premium quality 100% silicone Non-corrosive Neutral cure AS 4020 approved BENEFITS Quick exposure to light running water Suitable for use in all weather UV resistant Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$11.04
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution Product Overview Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium. Key Features & Benefits Quick exposure to light running water UV resistant for lasting outdoor use Neutral cure, making it versatile and safe for different materials Non-corrosive and AS 4020 approved Compatible with Monarch Mini Compact Caulking Gun Perfect For Great for small projects where a full-size cartridge is not needed. Ideal for: Repairing gutters Fixing roofs Mending downpipes Tight spaces that traditional cartridges can't reach Colors Available Available in black and translucent versions for versatility in your projects. How To Use Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
$7.35
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
Gorilla Tape To-Go Handy 1" Roll Convenient for on-the-go repairs, Gorilla Tape To-Go's 1 inch width packs a powerful grip in a portable size. With double-thick adhesive, tough reinforced backing and rugged weather-resistant shell, it sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. This size is ideal size for backpacks, toolboxes, glove compartments for camping, boating and more. Use like any other tape Tear by hand or cut to size Apply carefully smoothing out air pockets or rolls That's it, enjoy the strength and durability of Gorilla Tape
$11.07
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607409N_5d23d9cf-9af4-4971-af36-316c7ce35662.jpg?v=1754712479&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$26.69
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607126N_cffee80a-3f6c-4f18-ab8b-4a06da2ea9e8.jpg?v=1754712484&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.60
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600127N_b3248bad-00e4-4a61-873b-21199bac68a6.jpg?v=1754712486&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$15.51
Introducing Gorilla All Weather Tape - Your Ultimate Outdoor Repair Companion! When it comes to outdoor repairs, ordinary tapes just won't cut it. That's where Gorilla All Weather Tape steps in! Engineered with unbeatable strength and a weather-resistant shell, this tape is the ultimate solution for all your outdoor repair needs. Brace yourself for the power of Gorilla All Weather Tape! This incredible tape is equipped with a permanent, low tack adhesive that bonds with tenacity. No matter the challenge, it holds strong and steadfast, making sure your repairs stand the test of time. Rain or shine, Gorilla All Weather Tape delivers exceptional performance. Its waterproof design resists drying, cracking, and peeling caused by sunlight, heat, cold, and moisture, making it ideal for extreme weather conditions. Experience the versatility of Gorilla All Weather Tape! It works effortlessly in both hot and cold temperatures, ensuring it remains your reliable partner no matter the season. Ease of use? Check! Applying Gorilla All Weather Tape is a breeze. Simply tear it by hand or cut it to size with a knife or scissors. Carefully apply the tape, smoothing out any pockets or rolls, and voilà! You're all set to enjoy the strength and durability of Gorilla Tape! For optimal results, ensure the surface is clean, free of dust, dirt, and debris. Store the tape flat on a non-delicate surface, keeping it away from direct sunlight. Technical Specs: Application Temperature: Above 4° C Service Temperature: -17° C to 93° C Indoor: Yes Outdoor: Yes Moisture Resistant: Waterproof Frequently Asked Questions: Q: Can Gorilla All Weather Tape be used instead of electrical tape? A: Gorilla All Weather Tape should NOT be used as an electrical tape. Q: Will Gorilla All Weather Tape work on plastic/vinyl/rubber? A: Yes, Gorilla All Weather Tape contains a highly concentrated rubber-based adhesive and sticks to most plastics, including polyethylene (PE) and polypropylene (PP). However, it does not work on materials with high oil or plasticizer content, such as EPDM rubber or PVC. For those materials, we recommend using an acrylic tape like Crystal Clear Gorilla Tape. Q: Is Gorilla All Weather Tape food safe? A: Gorilla All Weather Tape is not recommended for direct or indirect food contact and should not be considered food safe. When it comes to outdoor repairs, don't compromise. Choose the unmatched strength and durability of Gorilla All Weather Tape. Tackle any challenge, withstand any weather - trust Gorilla to get the job done right!
$32.60
Meet your go to epoxy putty for fast, permanent style repairs. Gorilla All Purpose Epoxy Stick is a hand mixable putty that sets in about 10 minutes and cures in 24 hours to a tough, machinable finish. Once cured it can be drilled, sanded, and painted. It is waterproof, non rusting, and ready for indoor or outdoor jobs around the home, car, boat, and garden. Why you will like it Fast setting. Approximate set time 10 minutes. Paintable after about 1 hour. Full cure in about 24 hours for a hard wearing repair. Works on most common materials including metal, PVC, many rigid plastics, wood, stone, ceramic, brick, concrete, fiberglass, and glass. Non rusting formulation for durable repairs in wet or humid areas. Waterproof when cured. Suitable for indoor and outdoor use. NSF ANSI 61 certified drinking water safe for contact with potable water once cured. Great for Plumbing repairs such as sealing low pressure leaks and patching drainage pipes Automotive trims and general panels that do not exceed service temperature of typical epoxy repairs Household fixes like filling holes, anchoring hardware, rebuilding small parts, and edge repairs DIY and craft projects that need a sculptable, sandable fill Important use notes Not for exhaust systems. For plumbing, use for temporary repair of drainage pipes or low pressure pipes only. Turn water off, apply, then wait at least 1 hour before turning water back on. Bonded wood should not be submerged or soaked after repair. How to use Wear disposable gloves. Work in a well ventilated area. Prepare the surface. Clean off dust, oil, and loose material. Roughen smooth surfaces with sandpaper. Cut the amount you need. Remove the film wrapper and foil sticker. Reseal unused putty to limit air exposure. Knead for 30 to 60 seconds until the colour is uniform. Mix thoroughly or it will not harden completely. Apply within 5 minutes of mixing. Press firmly into place. Smooth with wet gloved fingers if a smooth finish is desired. Remove any squeeze out before hardening. Allow to set about 10 minutes. Paint after about 1 hour. Full cure about 24 hours. Specifications Format Hand mixable epoxy putty stick Size 56.7 g Set time About 10 minutes Paintable After about 1 hour Full cure About 24 hours Indoor or outdoor Yes, waterproof when cured Drill, sand, paint after cure Yes Drinking water contact NSF ANSI 61 certified drinking water safe once cured Clean up and storage While uncured, wipe away with soap and water, acetone, or isopropyl alcohol. For cured material, remove by sanding, scraping, or chiseling. Store the stick in its vial with film and foil sticker re applied. Keep sealed in a cool, dry place. Keep away from children and animals. Safety Wear gloves during mixing and application. Avoid contact with skin and eyes. If in eyes rinse with water for 15 minutes. If on skin wash with soap and water. Use in a well ventilated area. For medical emergencies in Australia call 000.
$14.47
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.10
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$17.25
You have seen 144 out of 161 products
Keep water out of joints, seams and enclosures with waterproof and weatherproof products. Match cure type and flexibility to the application (bathroom, kitchen, outdoor). Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
