A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. Safety: Avoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. If swallowed, seek immediate medical advice. Always refer to the MSDS available on the Dunlop website.
$139.40
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$64.80
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$18.48
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details
$144.00
Davco® Sanitized Tile & Grout Sealer is a solvent-based sealer that provides excellent protection against stains, soiling, discolouration, and efflorescence. It’s an easy-to-apply, clear solution that cures to form an invisible, water-repellent coating. Key Benefits: Clear solution that cures to an invisible, water-repellent coating Easy to apply Usage: Surfaces: Only suitable for cement-based grouts Can be applied over most unglazed porous ceramic tiles Areas: Suitable for both interior and exterior applications Ideal for commercial and domestic wall and floor grout joints Advantages: Protects against stains, soiling, and discolouration Provides an invisible protective layer that repels water Perfect for enhancing the durability of grout in high-traffic areas
$20.98
Concentrated grout additive designed to increase the flexibility, strength and water resistance of cement based grouts. Davco® 4 in 1 Grout Additive is suitable for interior and exterior domestic applications. Ideal for submerged and high foot traffic areas, where a high degree of deformability is required. Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence Usage To reduce the porosity of cement based grouts To improve the compressive strength of cement based grouts To improve the flexural strength of cement-based grouts Suitable for use when grouting over fibre cement sheet floors and swimming pools or where a greater performance level / heavy duty performance is required Advantages Increases flexibility, strength and water resistance of cement based grout Enhances the colour of grout Reduced likelihood of efflorescence
$24.80
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$6.59
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
Bostik Seal it Kitchen & Bathroom White: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Seal it Kitchen & Bathroom Translucent: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
Betta Tilecare Tile & Grout Sealer waterproofs porous tiles and grout without leaving a slippery film coating, making it perfect for kitchens, bathrooms, and other tiled areas. Drying Time: Recoat: 15 minutes Full Dry: 24 hours Coverage: 1L covers 5-10m² Available Sizes: 1L, 4L, 300g Aerosol, 500ml Wheel Applicator, 750ml Trigger Application Method & Cleanup: Tools: Paint brush, roller, or pump spray Features: Water-based formula Clear penetrating finish Invisible, moisture-repellent coating Easy to use Proven technology Non-slip finish Preparation: Remove any silicone sealant strips and soap build-up. Clean mould off tiles and grout using Betta Tilecare Mould Rid™ or bleach. Rinse thoroughly with water after cleaning. Remove and patch all loose or missing tile grout. For improved results, add Bondall HydroCrete to the grout mix. Ensure the application area is dry for 12-24 hours before applying the sealer. For porous surfaces or after high-pressure washing, allow 3-4 days drying time before sealing. Application: Start from the top of the wall, applying Tile & Grout Sealer liberally over tiles and grout. Finish by applying the sealer to the shower base or floor. Ensure even coverage across all surfaces. Drying: Wait at least 15 minutes for the first application to react before reapplying. After the second application, wait another 15 minutes, then use a dry cloth to remove any excess from the tile surface. Allow 24 hours before using the sealed area. Tips & FAQs: Not for Water Holding Vessels: This product is not intended for waterproofing items like ponds or fish tanks. Test Before Use: Always test on a small, inconspicuous area to ensure it provides the desired result. Avoid Over-application: If the sealer runs or pools, wipe down with a clean, dry, low-lint cloth. Apply Evenly: Take care to apply evenly, especially on pitted surfaces. Pre-treat Stains & Mould: Ensure stains, moss, and mould are treated prior to sealing. Avoid Pooling: Do not allow the product to pool or over-apply on surfaces. Betta Tilecare Tile & Grout Sealer is a reliable and easy-to-use product for waterproofing and protecting your tiles and grout, providing long-lasting protection without altering the natural appearance of your surfaces.
$27.94
Betta TileCare Tile & Grout Sealer with Wheel Applicator is a premium, water-based penetrating sealer that forms an invisible moisture-repellent barrier. Ideal for use in bathrooms, kitchens, laundries, and other wet areas, it helps prevent water damage, stains, and mould growth on porous tiles and grout. The included wheel applicator makes sealing fast and easy, delivering smooth and precise coverage with minimal mess. Once cured, it dries clear without leaving a slippery or glossy finish, maintaining the natural look of your surfaces. Surface Preparation Ensure surfaces are clean, dry, and free of mould, soap scum, and any existing sealers or coatings. Remove silicone sealants prior to application. For best results, allow grout and tiles to dry for at least 24 hours before sealing. Heavily porous surfaces may require 3–4 days of drying time. Application Instructions Shake well before use. Starting from the top of the area, apply sealer evenly using the wheel applicator. Ensure all tile and grout lines are thoroughly coated. Allow to absorb for 15 minutes. Reapply a second coat if needed. Wipe away any excess product from tiles with a clean, dry cloth. Avoid heavy foot traffic or moisture exposure for at least 24 hours after final coat. Coverage Approx. 5–10m² per litre depending on tile and grout porosity. Drying Time Touch dry in 15 minutes Fully cured in 24 hours Clean-Up Clean tools and applicator with water immediately after use. Technical Data Appearance: Milky white (dries clear) Base: Water-based penetrating sealer Finish: Invisible, non-slip Application method: Wheel applicator Suitable for: Porous tiles and grout (indoor use)
$21.32
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$28.00
You have seen 161 out of 161 products
Keep water out of joints, seams and enclosures with waterproof and weatherproof products. Match cure type and flexibility to the application (bathroom, kitchen, outdoor). Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
