![Selleys No More Gaps Bricks Mortar [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697130334_5a88883c-9e8a-4c25-80f6-535ba26ac80d.png?v=1754711844&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$28.39
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.50
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$22.00
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$20.69
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$16.56
Selleys Kwik Grip High Temp Spray: Heat & Water Resistant Adhesive for Extreme Conditions Bond Like a Pro: From Marine Carpets to Car Interiors Presenting Selleys Kwik Grip High Temp Spray, a premium adhesive formulated to withstand extreme heat up to 90 degrees and resist salt water. Ideal for tasks requiring high-grade adhesion, from car headlining repairs to marine carpet installations. Key Features: Heat resistant up to 90 degrees Water and salt water resistant Fast drying High grab Applications Include: Repairing headlining in cars Adhering marine carpets in boats Suitable Materials: Wood Metal Aluminium Fabric Polyurethane foam Laminate Leather Felt Cork How to Use: Clean and dry the surface before application. Shake the can well and hold it 20cm away from the surface. Spray both surfaces liberally. Wait for up to 5-10 minutes for the adhesive to become touch dry. Align and press the surfaces together, applying
$25.00
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.78
Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.
$48.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. UsesLiquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirableSkirting boards, architraves, cornicesWall panelling to masonryStyrene foam to metal roofing Technical FeaturesFast grab – high initial holding minimises slippage when adhering on vertical surfacesMeets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards)Does not drip, sag or string between panelsBridges gaps and will adhere materials with uneven surfacesLow mess – excess and squeeze out is easily cleaned up with wet clothNo solvent fumes – ideal for large indoor jobsHigh flexibility – will withstand thermal movement and vibrationHigh heat resistance – will not lose bonds exposed to sunPaintable when dryEasy to extrude at all temperatures Application TipsLiquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.)Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications.In cold or damp weather and between non-porous materials drying time is greatly extendedThick applications take longer to dry than thin applicationsPre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and PerformanceFor porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. AppearanceLump free, air-free smooth beige paste Specific GravityApprox. 1.44g/mL @ 25oC ViscosityTypical 7000 – 9000 Poise SlumpTypical: 0mm Shear Adhesion Strength (7 days) (AS2329)Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure)Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs)Over 200kPa Heat ResistanceBonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oCThis data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. CleaningLiquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$8.93
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$19.41
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$8.28
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$28.49
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$23.38
Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Details Whether you're beautifying the exterior of your home, or reinforcing your mailbox, Scotch-Mount™ Outdoor Double-Sided Mounting Tape is the one to choose for a hassle-free, permanent bond. Designed to deliver exceptional adhesion, this powerful double-sided tape holds up to 15 pounds because of its 3M™ industrial strength adhesive. It's compatible with a variety of surfaces and conforms easily. If you are looking for a weather resistant way to quickly and easily mount or fix items outdoors, look no further than Scotch-Mount™ Outdoor Double-Sided Mounting Tape. Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA from globally sourced materials Available in various sizes Color: Grey
$13.95
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$39.64
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$8.40
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$165.00
Manufactured from special fibred paper with added tensile strength. Buffed on both sides to ensure optimum bonding and holding power. Perforated for ease of use and better adhesion. Easy to use DIY with professional results Strong bonding and holding power Self adhesive Quick results
$13.95
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$9.35
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$39.15
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$46.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$28.90
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40 m2 Number of Coats: 2 Recoat: 24hrs Sheen Level: Pale Satin
$15.95
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$19.95
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$8.12
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$33.95
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$9.33
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$185.00
Directions: Spray affected area Allow penetrating for 5 to 10 minutes with a damp cloth Wipe over Allow drying Uses: Household, motor vehicles, boating & office carpets
$4.00
Multi-Purpose Cleaner and Deodorizer Natural Minerals easily dissolve in water Directions: Test on an inconspicuous area first Borax can be used in powder form for tea and coffee cup stains General cleaning 1-table spoon to 4.5 Litres of warm water (also woollens and blankets) Enamel surfaces 4 tablespoons to 4.5 Litres of warm water (refrigerators, stoves, sinks, baths & tiles Uses: General cleaning, stain remover, deodorizer
$9.47
Polyfilla Rapid 30 340g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 340g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 340g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$36.88
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$21.59
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$38.10
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 500g and 2.2kg Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.91
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
$5.00
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
PC-Lumber™ Epoxy Putty is pre-measured and mixed by hand. It is used as a filler where a small amount will solve the problem. Within 60 minutes it is cured and ready. The putty can be easily formed and shaped. Here are just a few specific uses (there are hundreds of other uses): Reset or secure loose hardware in wood (hinges, handles, latches, etc.) Fill abandoned screw and nail holes in cabinets or paneling Fill dings and dents in molding or doors Fill woodpecker and carpenter bee damage to exterior siding and paneling Rebuild display corner in retail store
$14.46
PC-Concrete ™ Anchoring and Crack Filling Epoxy— is the epoxy chosen to repair cracks in a warehouse and factory floors. Dispense and apply using a standard size caulking gun. Cures hard enough to drive over within 3 hours at standard temperature. Nothing stronger for your anchoring applications. PC-Concrete™ is a two-component (1:1 ratio), 100% solids, high modulus, and structural epoxy paste. PC-Concrete™ is a solvent-free, no odour, high strength, moisture insensitive epoxy system. The resin and hardener are uniformly dispensed from a 9-ounce cartridge system and mixed through a mixing nozzle using a standard size caulking gun. (We recommend at least an 18:1 thrust ratio). PC-Concrete™ is also provided in a 22-ounce dual cartridge system for Contractors and Professionals. This size requires a 600ml high thrust dual cartridge dispensing gun. For filling larger cracks and cavities use the 102-ounce bulk kit. PC- Concrete™ will NOT SHRINK. Suitable for Interior and Exterior applications. Can be applied to WET & UNDERWATER surfaces. Here are just a few specific uses (there are many other uses): Anchor into marine docks above or below waterline Anchor equipment to floors Bond to pre-stressed floors Anchor into stone and rock. Install anchor bolts for sill plates Anchor into foundations and block Fill cracks in concrete allowing equipment traffic In 4 hours Anchor into concrete railroad ties Anchor HVAC equipment to concrete pads and roofs Waterproof floor to wall cracks Re-anchor railing at convention center or apartment building Anchor seats in lecture hall or theaters Repair broken concrete in shopping mall parking garage Fill spalled concrete in car wash Fix fork truck damaged concrete in warehouse Seal crack in sanitation and chemical storage facility containment area Repair floor in fire station garage Anchor safe to floor prison and security pickproof epoxy Anchor machinery
$14.46
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$8.89
You have seen 240 out of 626 products
Reliable, tidy solutions for typical weekend tasks: mounting, gap filling, sealing, small timber or tile repairs and quick décor updates. Prioritise fast-set or instant-bond options to keep projects moving, and pick paintable/sandable finishes for a clean result. Use filters to refine by chemistry, cure profile and application method. Always review the product page and TDS/SDS for prep, working time and return-to-service guidelines.
