Bostik Spray Adhesive is a clear, fast-tack, multi purpose aerosol glue designed for quick and easy bonding of lightweight materials. Ideal for craft, school, office, and general household repairs where a neat, even spray is preferred. Why you’ll love it Fast tack with strong initial grab Clear, low-mess spray pattern for even coverage Adjustable bond: reposition briefly, then press firm Non-staining on most materials Great for large areas and edge-to-edge laminations Suitable materials Paper, cardboard, photos, craft foam, felt, fabric, foil, leather, cork, many plastics, wood, and light laminates. Always test on delicate or coated surfaces. Typical uses Mounting posters, photos, and presentations Craft projects and scrapbooking Attaching fabric or felt to displays Temporary positioning before stitching or stapling How to use Ensure surfaces are clean, dry, and free of dust or oil. Shake the can well before and during use. Hold 15–20 cm from the surface and spray a light, even coat. For temporary bonds, spray one surface only and join after 10–30 seconds tack time. For stronger bonds, spray both surfaces, allow to go tacky, then press together with firm, even pressure. Drying and cure Tack time: typically 10–60 seconds depending on coat weight and conditions Handling strength: a few minutes Full bond development: 24 hours Clean up While wet, wipe overspray from hard surfaces with a suitable adhesive remover or mineral turpentine, then wash with warm soapy water. Test cleaners on an inconspicuous area first. Good to know Clear finish when dry Best at room temperature with good ventilation Not recommended for high heat, heavy structural loads, or polyethylene and polypropylene unless tested Storage and safety Store upright in a cool, dry place away from heat and flame. Use only in well ventilated areas. Avoid inhalation and contact with eyes or skin. Keep out of reach of children. Press nozzle briefly upside down after use to clear. Specifications Format: Aerosol spray Colour: Clear Size: 350 g
$35.00
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
BBQ Tough Clean Grease & Grime Spray 400 g Bring your grill back to spotless condition with BBQ Tough Clean. This powerful, non-caustic formula is specially designed to lift away grease, fat, and charred food from BBQ plates, grills, and racks, giving you a cleaner and healthier cooking surface without harsh fumes. Key Benefits: Powerful cleaning: Penetrates and dissolves stubborn grease and grime. Spotless results: Leaves BBQ surfaces residue-free for safer cooking. Non-caustic & low fume: Safer to use around your outdoor cooking area. Cold application: Designed to work when the BBQ is cool (before use). Perfect For: Stainless steel and cast iron BBQ plates, grills, and racks Removing built-up food, grease, carbon deposits Deep cleaning before a big barbecue or regular maintenance How to Use: Make sure your BBQ is cold. Remove the racks, grills and plates if possible. Scrape off excess debris and wipe loose grease. Shake the can well and spray liberally onto the surface from upright position. Allow to sit at least 10 minutes (for tough grime, up to 2 hours), then wipe with a damp cloth or scouring pad. Rinse thoroughly with water and dry with a clean cloth. Optional: apply a light coat of cooking oil to surfaces to protect against corrosion. Important Safety & Usage Notes: Do not use on hot BBQs Avoid spraying on painted, plastic or aluminum surfaces. If overspray lands on unintended areas, wipe off immediately and rinse. Not intended for use on exterior, non-cooking surfaces (use an exterior BBQ cleaner for those parts). Keep out of reach of children and pets. Use protective gloves and avoid inhaling fumes.
$7.02
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Ash Meranti]](http://gluesaustralia.com.au/cdn/shop/files/9300611329301.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Cypress Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9300611329400.jpg?v=1754724101&width=645)
A water-based timber and grain filler, suitable for both interior and exterior use. Woodblend sands to an extremely fine, smooth finish. Woodblend can be coated with water or oil-based timber finishes and paints. Available in six inter-mixable colours. KEY PRODUCT INFORMATIONCoverage: 5m2/LRecoat: 2hrsFull cure: N/AClean up: WaterSheen: N/A USAGE INSTRUCTIONS WHERE TO USEAreas: All interior timber, Exterior timberSubstrates: All interior timberLocations: Interior, Exterior APPLICATIONMethods: Filling blade or knife 1. Apply WoodBlend with a flexible filling blade or knife. Fill deep holes in approx. 10mm stages, allowing two hours drying time between each stage.2. To ease application, dampen blade with water.3. Wipe off excess with a slightly damp sponge. When dry, sand to a smooth finish.4. When using clear finishes, apply WoodBlend after the first coat of clear to minimise smudging.5. For use as a grain filler, thin WoodBlend with 5-10% water to achieve the required consistency. Apply with a flexible filling blade or knife and allow to dry. When dry, sand back to bare timber, leaving filler only in the grain. IMPORTANT: Keep container tightly closed when not in use.
$20.34 - $45.73
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
Skimming wall board top coat. Smooth ready to paint surface. Fine cracks, imperfections and feathering. Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
$14.10
Skimming wall board top coat. Smooth ready to paint surface. Fine cracks, imperfections and feathering. Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
$27.87
Casting, modelling, moulding, sculpting, carving. Fine quality to hold detail. Sands smooth.
$16.64
Ready to use, hard drying acrylic putty filler Ideal for repairing cracked, broken or uneven surfaces 30 minute fast drying time Includes bonus applicator Suitable for fibrous cement, brick, plaster and wood surface repairs available in 500gm/1.5kg Not suitable for wet areas or where structural movement occurs
$19.15
The UNi-PRO snap blade knife is the perfect tool for all your tasks. From opening packages to cutting string, this durable and convenient multi-purpose knife will make life easier!
$6.50
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$5.05
The UNi-PRO Real Good Scrapers are a comprehensive range of scrapers, perfect for DIY jobs such as removing flaky paint or silicone. The blades have been extremely durable and reliable in various weather conditions and over time. With the scraper being made from high quality German steel that has resistant to corrosion, your professional tool will last just as long as you do!
$8.05
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C. Materials Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard. Not suitable for leather clothing, textiles, PE and PP. Use and Handling Instructions Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
$10.74
Ultra-fast and extremely strong universal super glue. Its liquid formula is easy to spread and flows into smallest corners and joints. UHU Super Glue is easy to apply, bonds quickly and provides lasting, extremely strong results. You can use it on a variety of materials so it's perfect for keeping handy in the classroom at school. You can use the glue on plastics, ceramics, wood, porcelain, metal and rubbers. It bonds quickly for fast results. The glue will flow into small corners and tight spaces. The results are extremely strong and long lasting.
$7.00
Blue glue stick "Made in Germany" where you directly see where you glue. Applies blue and magically dries clear. With an unique screw cap that prevents glue from drying out. The glue formula consists of 70% natural ingredients (including water) and is solvent free. Glues strong, fast and durable, glides smoothly, is highly efficient and of course cold washable. For use at home, at school and in the office. Materials Glues paper, cardboard, photos, Styrofoam®, labels, etc. Use and Handling Instructions UHU stic Magic is applied with light pressure onto the materials to be glued. The parts are put together immediately after applying the glue. The blue colour disappears a few seconds after application and is completely transparent when dry. Features: Applies blue and magically dries clear Glue formula with 70% natural ingredients Glues fast, strong and durable Screw cap prevents glue from drying out
$3.50
Ultra high-strength 2-component epoxy adhesive for the heaviest loads (up to 1700 N/cm²). Working time: 90 minutes, handling strength: 6 hours, final bond: 24 hours. Can be drilled, sanded and painted. Resistant to impact, ageing, dampness, heat and cold. Suitable for metal, stone, concrete, marble, china, wood, glass, duro-plastics, glass-fibre reinforced plastics, rigid PVC and Styrofoam.* Not suitable for PE, PP, PS, soft PVC. UHU Epoxy Quick Set High-performance 2-component epoxy adhesive for quick and reliable repairs. Dries clear. Working time: 5 minutes, handling strength: 20 minutes, final bond: 12 hours. Resistant to impact, ageing, dampness, heat and cold.
$8.57
Powerful universal adhesive for most plastics. Cold welding technology for a perfect bond. Ideal for multi-purpose domestic applications, handicraft work, repairs and model building. The hard but flexible adhesive film remains transparent. Water and temperature resistant. Toluene free. YOU CAN FIX IT! Glues most usual plastic materials (ABS, Plexiglas®, hard PVC...), also in combination with wood, metal, glass and ceramics. *Not suitable for PE, PP and Styrofoam.
$12.77
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, benchtops, tiles, slate, stainless steel, baths, glass, stovetops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQs. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra-concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$5.33
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
$16.48
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
Original formula Super Glue forms the strongest bonds in tight joints between clean breaks or smooth surfaces. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly sets in seconds and is packaged in a long lasting 2-gram tube. The extra slim card is perfect for tight displays, end-caps and clip strips. Pacer Technology Super Glue is a quick-setting adhesive that bonds strongly and works best on: Metal Rubber Most Plastics Aluminium Ceramic China Wood Pottery Jewellery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Use: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep container pointed away from face and body. Carefully follow opening directions on package. Unscrew cap while keeping container pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before resealing cap securely. Storage: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$3.50
Original formula Super Glue forms the strongest bonds in tight joints between clean breaks or smooth surfaces. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly and sets in seconds! Packaged in a 20-gram break-away tip bottle this product is ideal for larger projects that require greater amounts of Super Glue. Works best on: Metal Rubber Most Plastics Aluminium Ceramic China Wood Pottery Jewellery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) USE INSTRUCTIONS: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep container pointed away from face and body. Carefully follow opening directions on package. Unscrew cap while keeping container pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before resealing cap securely. Storage: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$12.50
Single Use Waterproof Epoxy Adhesive is the perfect product to use when you need to do any marine or waterproof projects. It works under or in the presence of water and remains waterproof. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly and are easy to mix. This product sets in only 3-4 hours.
$29.00
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$18.00
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes. Works best on: • Porous materials • Ceramic • Metal • Pottery • Wood • Tile • Crafts Properties: Initial colour: Green resin/white hazy hardener Maximum Gap: .25” Final colour: White hazy Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%) Handling Time: After 1 hour Aluminum: 900 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C) Instructions: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours. Helpful Hints: To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
$9.95
Extreme temperatures take a toll on rearview mirrors. After a bitter cold winter or hot summer, they tend to fall off. Our Rear View Mirror Adhesive is formulated to be strong and quick—enabling you to have your rear view mirror reattached in minutes. Works best on Glass to Glass Glass to Metal Metal to Metal Pacer Technology Super Glue’s Rear View Mirror Adhesive (14104, 15193) is a two-part system used for bonding rear view mirror brackets to windshields and for: Glass to metal Glass to glass Metal to metal Properties: Appearance: Part A – Activator/Accelerator – light blue transparent liquid Part B – Adhesive – yellow liquid adhesive Tensile Shear Strength (steel to steel): 2000 – 3000 psi Directions: Use in a well-ventilated area. Mark location on the outside of windshield with a removable marker. Make sure bracket is positioned correctly. Refer to the card for proper opening instructions. 1. Apply Activator to both surfaces. Allow 1 minute to dry. 2. Apply 2 drops of adhesive to the metal surface to be bonded. 3. Mate parts together using sufficient pressure to spread adhesive. Hold parts together firmly for 1 minute. Allow 1 hour before handling. Full strength develops in 24 hours. For optimum results, wait overnight before attaching the mirror to a bracket. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Activator – Contains isopropyl alcohol. CAUTION: Flammable. Irritating to eyes. Mild skin irritant. Do not ingest. If swallowed seek medical advice immediately and show this container label. Use and store in a well-ventilated area. KEEP OUT OF REACH OF CHILDREN. Adhesive – Contains methacrylate esters and acrylic acid. CAUTION: Irritating to eyes and skin. May cause sensitization by skin contact. Avoid contact with skin & eyes. In case of eye contact, rinse immediately with water for 15 minutes and seek medical advice. For skin contact, wash well with soap and water. If swallowed seek medical advice immediately and show this container label. KEEP OUT OF REACH OF CHILDREN.
$18.00
Red, permanent Thread Locker prevents loosening by filling in the inner spaces in threaded metal parts to form a tough solid assembly. Pacer Technology Super Glue Red Threadlocker (15191) is a high strength premium grade product used to permanently lock or seal metal threaded components or for metal fasteners up to 1” in diameter. Also prevents loosening due to high vibration. Appearance – red liquid with mild odour. Use Instructions: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow curing 24 hours for maximum strength. The excess adhesive on the outside of parts will not cure and can be removed with a solvent-soaked cloth. Storage and shelf life: Recap for storage. A one-year shelf life can be expected. CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists. KEEP OUT OF REACH OF CHILDREN.
$9.95
This new, innovative dispensing system allows for accurate control while utilizing an advanced formula of the Super Glue Corporation's signature product cyanoacrylate (Super Glue GEL). The easy to hold applicator design allows for either continuous stream or single drop control. No more sticky fingers! This glue works great when adhering to porous or vertical surfaces. It will not drip or run! Works best on: Aluminum Ceramic China Hard & Soft Wood Jewelry Metal Most Plastics Pottery Rubber Vinyl Pacer Technology AccuTool Gel (19026) is a quick-setting, non-sagging gel adhesive that fills gaps & works best on: Leather Metal Vinyl Rubber Most plastics Aluminium Ceramics Hard & Soft Wood China Pottery Jewellery Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800 F (-540 to 820C) Use: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove the outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage and Shelf Life: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$9.95
Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes. Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for: • Metal • Plastics • Ceramics • Wood • Glass • Rubber • Fabrics • Brick • Leather • Canvas • Concrete • China • Vinyl • Porous materials • Non-Porous materials Properties: Initial colour: Clear Final colour: Clear to light yellow Open Time: 10 minutes Dry Time: 30 minutes Handling Time: 3 hours Full Strength: 24 hours Operating Temperature Range: -200 to 1500F (-290 to 660C) Instructions: Use in a well-ventilated area. Protect work surfaces. As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts. As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed. For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours. Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$25.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40o F to +176oF (-40oC to +80oC) Instructions: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$29.95
$35.00
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$7.95
Please refer to the photo of the back of the pack for indications and instructions
$15.00
Blue, removable Thread Locker prevents threaded metal fasteners, nuts, bolts, and screws from loosening. Thread Locker is an advanced anaerobic adhesive. Pacer Technology Super Glue Blue Threadlocker (15190) is a premium grade product used to lock or seal metal threaded components or for metal fasteners up to ¾” in diameter. This product prevents loosening due to high vibration. Parts can be disassembled with simple hand tools. PROPERTIES: Appearance – blue liquid with mild odor. USE INSTRUCTIONS: For best results, parts should be clean and dry. Apply a bead around the part to be bonded & assemble with a twisting motion to spread adhesive. Allow to cure 24 hours for maximum strength. Excess adhesive on outside of parts will not cure and can be removed with a solvent-soaked cloth. STORAGE AND SHELF LIFE Recap for storage. A one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS CAUTION: IRRITATING TO EYES AND SKIN. Contains methacrylate esters and cumene hydroperoxide. Avoid contact with eyes and skin. May cause skin dermatitis on prolonged contact with sensitive individuals. In case of eye contact, rinse immediately with plenty of water and seek medical advice. Wash skin thoroughly with soap and water after use. Seek medical advice if skin irritation persists.KEEP OUT OF REACH OF CHILDREN.
$12.50
$15.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Pacer Technology Super Glue Quick Setting Epoxy (SY-QS, SYQS8, T-QS, 15250, 15350) works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40oF to +176oF (-40oC to +80oC) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours.
$19.95
Single Use Quick Setting Metal Epoxy Adhesive is perfect for repairing appliances, tools, etc. It bonds most metals including copper, steel, stainless steel, aluminum, brass and iron. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly, and are easy to mix. This product sets in only 5 minutes and the final cure color is light gray. Works best on: Aluminum Brass Copper Iron Stainless Steel Steel Properties: Initial colour: Light grey Maximum Gap: .25” Final colour: Hazy-clear Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 2500 psi (± 20%) Handling Time: After 1-hour Aluminum: 840 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 3000F (-400 to 1490C) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly until colour is uniform, approximately 1 minute. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
$12.50
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$25.48
You have seen 480 out of 858 products
Reliable, tidy solutions for typical weekend tasks: mounting, gap filling, sealing, small timber or tile repairs and quick décor updates. Prioritise fast-set or instant-bond options to keep projects moving, and pick paintable/sandable finishes for a clean result. Use filters to refine by chemistry, cure profile and application method. Always review the product page and TDS/SDS for prep, working time and return-to-service guidelines.
