Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$12.29
SikaSeal®-401 Aquarium Premium one-component aquatic life safe silicone sealant SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties. Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Usage Fish tanks Water pumps Aluminium Glass Advantages Extreme temperature resistance (-50°c to +250°c) Excellent vibration, UV and weathering resistance Good gap filling properties Highly versatile Easy to apply Aquarium safe Composition 1-C Silicone (acetoxy) Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Application Application steps SUBSTRATE PREPARATION Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry. CLEANING OF EQUIPMENT Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife. PRODUCT INFORMATION Composition 1-C Silicone (acetoxy) Packaging 75g Tube, 12 Tube per box Colour Clear Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions. Storage conditions Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC. Density ~1.02 kg/l Shore A Hardness ~23 Tensile Strength 1.0 N/mm2 Secant Tensile Modulus 1.1 n/mm2 Elongation at Break ~500% Ambient Air Temperature +5°c to +45°c Curing Rate ~3mm per 24 hours Skinning time ~7-10 minutes
$15.82
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$108.41
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant Product Highlights Fast Skinning Low Odour Paintable and Sandable Resistant to Ageing Silicone-Free Product Usage Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction. Compatibility Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates. Packaging Comes in a 310 ml cartridge for easy application. Technical Specifications Cure Mechanism: Moisture-curing Application Temperature: 535°C Shelf Life: 12 months when stored below 25°C Application and Removal For detailed application and removal guidelines, consult the manufacturer's manual. Precautions This product is intended for use by experienced professionals. Always perform tests for compatibility.
$27.72
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$15.39
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength. Uses: SikaBond Fast can be used on most substrates due to its excellent adhesion. These include: - Fixing polystyrene wall panels - Replacing loose tiles on walls - Skirting boards, architraves and trims to walls - Bonding panels to wall studs - Bonding particleboard, plywood, fibre cement and strip flooring to joists Advantages : - Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards” - Natural wood colour - Reduces the number of mechanical fasteners required to install floors or walls. - Can be repositioned for up to 60 minutes after application - Reduces squeaking associated with nail ride in floors - Paintable with water-based surface coatings - Easy to use one component - Bridges gaps up to 9 mm - Strong adhesion to metal - No fumes - High bond strength and heat resistance - Flows easily at all temperatures - Easy cleanup - Fast initial grab – minimises slippage on vertical surfaces Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous. Application Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Cleaning The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means. Technical Data (Typical) Colour Pale Brown Specific Gravity ~ 1.4 Skinning Time 20 minutes Repositioning Time 60 minutes Full Cure 24 hours depending on conditions When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation). Service temperature -5ºC to +90ºC Packaging 420 gram cartridge (12 cartridges per box)
$8.69
Instant set, high viscosity, multipurpose super glue Suitable for bonding substrates with irregular surfaces and in vertical applications Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials Can be used on porous substrates such as porcelain and china Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Surfaces with small irregularities max. 0.5 mm On vertical surfaces Characteristics and Advantages One Component Easy to apply, non-sag, gel consistency Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card Low consumption adhesive Versatile, allows adhesion between different materials Colourless Durable Packaging 3 g Tube
$12.00
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$16.13
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$88.91
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$15.46
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$23.60
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$41.00
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application. Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Wallboard Wood Masonry Plaster Primed nail heads Plasterboard Colours White Technology Water Based Use Interior Exterior (when painted) How To Use Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications). Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions. Handy Tips Painting with oil-based paints is not recommended until 24 hours after filler has been applied. Water based paints may be used immediately after filler has set. If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping or sanding.
$25.02
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler. Features Suitable for interior and exterior applications Good adhesions to most surfaces Water and weather resistant Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs What materials is this product suitable for? Mortar Masonry Concrete Wood Stone Primed metal surfaces Brick Plaster Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next. Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications). Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints. Limitations: Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps. Avoid using below 5°C or in wet conditions. Painting with oil-based paints is not recommended until 24 hours after the filler has been applied. Water-based paints may be used immediately after the filler has set. If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use.
$22.66
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula. Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm2/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
$13.90
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
![Selleys No More Gaps Filler Sealant Fast Dry [White]](http://gluesaustralia.com.au/cdn/shop/files/da7575e6045648c8aee7c9769b69a8cc.jpg?v=1757753086&width=645)
Selleys No More Gaps Fast Dry has been designed to be painted over in just 20 minutes so that you can finish the job sooner! No More Gaps Fast Dry also provides superior crack resistance with high flexibility and low shrinkage. Features Paint over in 20 minutes* Superior crack resistance Superior adhesion to a broad range of surfaces, resulting in a lasting finish A smooth flawless finish and minimal shrinkage Can be cleaned up easily and quickly with water Will not stain building materials Can be used indoors and outdoors *Allow longer drying times before painting with flat or ceiling paints or in cooler weather. Where can this product be used? Architraves Skirting boards Cornices Window and door frames Wall joints What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Painted surfaces Many other building materials How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into caulking gun such as Selleys Light Speed Caulking gun. Apply with caulking gun, forcing product into gap. For a smooth finish, smooth with a finger dipped in water. For a professional finish use a paint scraper such as a 50mm Soft Grip Scraper. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow to skin (about 20 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Limitations: For gaps between tongue and groove boards and weatherboards use No More Gaps® Exterior & Weatherboard. Where movement is excessive or for areas where contact with water is frequent, use the appropriate Selleys® Silicone Sealant. Handy Tips To avoid paint cracking, apply at temperatures above 10°C and do not apply paint too thick. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler, and a perfect finish. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to skin prior to painting, which is approximately 20 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. For exterior applications protect from rain until firmly skinned. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$7.56
Selleys No More Gaps Exterior is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Also available in easy tube format. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. Has good resistance to weathering Contains a titanium compound for superior UV resistance. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application).. Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack. Is formulated for long term resistance to cracking and crumbling. Is water based, so can be cleaned up with water. Will not stain building materials. Where can this product be used? Between exterior window and door frames Fascia boards and eaves Masonry Walls Tiling Timber & synthetic weatherboards Brickwork Fences Where shrinkage or movement has caused rigid fillers to crack Gaps with a maximum width of 25mm & depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Fibre cement sheeting, plasterboard Masonry Ceramic Tiles Glass Aluminium & other metals Many other building surfaces How To Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap. Smooth with a wet spatula, ensuring sufficient product remains in joint. Clean up with a damp cloth immediately. Allow to skin (about 30 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Protect from water until firmly skinned. Allow for longer skin and cure times in damp conditions. Limitations: For new weatherboard, check weatherboard manufacturers instructions before using this product Note that in very harsh conditions, joints between boards may expand beyond products movement capability. In such cases re-apply product and paint over. Not suitable for areas of continuous water immersion eg ponds Not suitable for application at below 5°C Protect from rain until the product has firmly skinned, and allow longer skin and cure times in damp conditions. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats and flat paints may crack on drying. To reduce this effect, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. For maximum durability on bare exterior surfaces, apply a coat of acrylic paint and allow to dry, before applying this gap sealant. Always paint over with a quality exterior paint. To ensure you get a professional finish ensure you paint with a good quality paint and paint brush. Painting with a good brush ensures the finish and durability of the paint is increased. We recommend a 50mm Edger Brush, as the cut angle of the bristles takes the work out of applying paint. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$11.00
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$24.79
![Selleys No More Gaps Bricks Mortar [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697130334_5a88883c-9e8a-4c25-80f6-535ba26ac80d.png?v=1754711844&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$28.39
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.50
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material. Uses Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc. Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems. Technical Features Will not discolour mirrors Heat and steam resistance Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings Adheres and forms a durable seal between sheet metals Gap filling on uneven surfaces Forms flexible/shock resistant bonds UV resistant Low odour during application Non corrosive Weather resistant Application Tips All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling. Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm). Fit nozzle to cartridge. Place cartridge into caulking gun. Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day). APPLICATION FOR MIRRORS For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them. Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes) The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours. Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling. Not recommended for fixing vinyl back mirrors If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed. GENERAL APPLICATION Apply as for mirrors and press surfaces together immediately Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond) Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day. Technical Details and Performance Indicative information only, not to be used for setting specifications. Consistency (As applied) Non-slump, solvent free paste Curing Mechanism Very rapidly develops an adhesive bond by reaction with moisture from the air Curing Rate 2mm depth per day Skin Forming Time 5-10 minutes (depending on weather conditions) Service Temperature –60°C to +150°C Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area) After 24 hrs: 280KPa After 48 hrs: 550KPa After 7 days: 830KPa Coverage 15 metres of a 5mm diameter bead Cleaning Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
$22.00
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces. Features Fast cure in 10 minutes*. More than twice the strength of conventional solvent-based construction adhesives. Waterproof – Uncompromising durability, with excellent water, weather and heat resistance. Can be used to bond most materials, and for most interior & exterior applications. Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability. Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below. Does not drip, sag or string between panels. Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials. Product expands slightly as it cures. The dried adhesive is paintable. *Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather. *Limitations – Not suitable for sole fixing or structural bonding. Where can this product be used? Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary. These include applications where: Extra water resistance is essential. eg. Exterior applications such as decking. Extra strength is required. Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight. Plastic substrates which are sensitive to solvent-based adhesives are used. Metal installations in which solvent-based adhesives will be slow to cure. Liquid Nails Waterproof is also suitable for typical construction applications such as: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite What materials is this product suitable for? Timber MDF Plasterboard Plastics (Pre-test to determine suitability) Masonry Concrete Particleboard Metals Rubber Tiles LOSP treated pine How to use this product General Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off. 1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter). 2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.) 3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting. 4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.* Liquid Nails Rapid Cure will achieve a full cure in 24 hours. *Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure. Handy tips Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin. Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure. The product should not be applied below 5°C. LIQUID NAILS Rapid Cure expands slightly as it cures. Not suitable for sole fixing for structural bonding. LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications. Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine. Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding. Safety tips If swallowed, do NOT induce vomiting. Avoid skin contact. Avoid breathing in vapours. Ensure you use a well-ventilated area The product is an eye, skin and respiratory irritant and can potentially cause irritation. Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in a cool place. The adhesive should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
$20.69
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$16.56
Selleys Kwik Grip High Temp Spray: Heat & Water Resistant Adhesive for Extreme Conditions Bond Like a Pro: From Marine Carpets to Car Interiors Presenting Selleys Kwik Grip High Temp Spray, a premium adhesive formulated to withstand extreme heat up to 90 degrees and resist salt water. Ideal for tasks requiring high-grade adhesion, from car headlining repairs to marine carpet installations. Key Features: Heat resistant up to 90 degrees Water and salt water resistant Fast drying High grab Applications Include: Repairing headlining in cars Adhering marine carpets in boats Suitable Materials: Wood Metal Aluminium Fabric Polyurethane foam Laminate Leather Felt Cork How to Use: Clean and dry the surface before application. Shake the can well and hold it 20cm away from the surface. Spray both surfaces liberally. Wait for up to 5-10 minutes for the adhesive to become touch dry. Align and press the surfaces together, applying
$25.00
A versatile hand kneadable, fast setting, non-rusting co-extruded epoxy repair system that can be used for repairing ferrous and aluminium metal items. It comes in a handy roll form, with the black hardener encapsulated in the grey resin part. The product hardens in 5-10 minutes, after mixing, to a black metal-like material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under water (but dry surfaces for application are best and recommended). Rapid Set (less than 10 minutes). Can be used for fuel resistant repairs. Appearance Dries Dark Grey/Charcoal Where can this product be used? Rebuilding engine parts and rusted metal etc Repairing a hole in a fuel tank Repair of iron pipes, tools and equipment Repair stripped threads Forming of nuts and bolts in place Attaching fixtures and signs Fixing radiators Repairing holes in cars and boats Patching ducts and tanks Making prototypes Thread locking Repair of down pipes and gutters Anchoring of bolts Repairing your metal outdoor furniture Set time increases at temperatures below 20°C Not recommended for plastic fuel tanks Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Not tested for drinking water contact to AS/NZ 4020:2005 What materials is this product suitable for? Steel Wide range of terrous metal and aluminium items Most plastics (pre-test required) Glass How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning Cut off required amount. Replace disc on remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to uniform colour. If mixing is difficult, warm to room temperature. Apply with pressure to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Steel will harden and begin to form a strong bond. After 60 minutes Knead-It Steel may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour, and feel a mild heat radiating from thre knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Store in a cool place for maximum shelf life Use Knead-It Multi Purpous for applications in contact with drinking water. Use Knead-It Aqua for applications in wet/submerged areas. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Steel. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.78
Features Resists intense heat Sets hard Water clean up Where can this product be used? Repairing bricks in fireplaces and chimneys Sealing flues in pot-belly stoves Filling cracks in ironworks and bricks What materials is this product suitable for? Brick Metal Concrete How to Use: Remove all dust, grease and loose debris before applying material. Dampen the cavities on porous surfaces for better adhesion. Apply Fireproof Cement firmly into holes and cracks with a damp knife or spatula. Allow Fireproof Cement to dry a minimum of 48 hours before exposure to heat. If Fireproof Cement is stiff slacken with a little water. Limitations: Fireproof Cement is not an adhesive - it is a filling compound. Not recommended for external use e.g. BBQ's, incinerators etc. Fireproof Cement is not suitable for use in kilns. Fireproof Cement is not recommended for moving joints such as expansion joints as it sets rigidly Hardened material cannot be resoftened with water.
$48.00
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. UsesLiquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirableSkirting boards, architraves, cornicesWall panelling to masonryStyrene foam to metal roofing Technical FeaturesFast grab – high initial holding minimises slippage when adhering on vertical surfacesMeets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards)Does not drip, sag or string between panelsBridges gaps and will adhere materials with uneven surfacesLow mess – excess and squeeze out is easily cleaned up with wet clothNo solvent fumes – ideal for large indoor jobsHigh flexibility – will withstand thermal movement and vibrationHigh heat resistance – will not lose bonds exposed to sunPaintable when dryEasy to extrude at all temperatures Application TipsLiquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.)Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications.In cold or damp weather and between non-porous materials drying time is greatly extendedThick applications take longer to dry than thin applicationsPre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and PerformanceFor porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. AppearanceLump free, air-free smooth beige paste Specific GravityApprox. 1.44g/mL @ 25oC ViscosityTypical 7000 – 9000 Poise SlumpTypical: 0mm Shear Adhesion Strength (7 days) (AS2329)Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure)Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs)Over 200kPa Heat ResistanceBonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oCThis data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. CleaningLiquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$8.93
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$19.41
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$45.65
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$8.28
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$28.49
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$23.38
Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Details Whether you're beautifying the exterior of your home, or reinforcing your mailbox, Scotch-Mount™ Outdoor Double-Sided Mounting Tape is the one to choose for a hassle-free, permanent bond. Designed to deliver exceptional adhesion, this powerful double-sided tape holds up to 15 pounds because of its 3M™ industrial strength adhesive. It's compatible with a variety of surfaces and conforms easily. If you are looking for a weather resistant way to quickly and easily mount or fix items outdoors, look no further than Scotch-Mount™ Outdoor Double-Sided Mounting Tape. Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA from globally sourced materials Available in various sizes Color: Grey
$13.95
Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Details Whether you're beautifying the exterior of your home, or reinforcing your mailbox, Scotch-Mount™ Outdoor Double-Sided Mounting Tape is the one to choose for a hassle-free, permanent bond. Designed to deliver exceptional adhesion, this powerful double-sided tape holds up to 15 pounds because of its 3M™ industrial strength adhesive. It's compatible with a variety of surfaces and conforms easily. If you are looking for a weather resistant way to quickly and easily mount or fix items outdoors, look no further than Scotch-Mount™ Outdoor Double-Sided Mounting Tape. Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA from globally sourced materials Available in various sizes Color: Grey
$34.85
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$39.64
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$8.40
You have seen 240 out of 858 products
Reliable, tidy solutions for typical weekend tasks: mounting, gap filling, sealing, small timber or tile repairs and quick décor updates. Prioritise fast-set or instant-bond options to keep projects moving, and pick paintable/sandable finishes for a clean result. Use filters to refine by chemistry, cure profile and application method. Always review the product page and TDS/SDS for prep, working time and return-to-service guidelines.
