A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$13.66
Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits. Ideal to use on tiles, porcelain, sinks, showers and baths
$7.00
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
Interior and exterior use Acetic cure Excellent bond to glass Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks. Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
$11.57
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond Instant strong bond Sets in 10 seconds Dries clear
$3.41
The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children. Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!
$11.57
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$26.68
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $11.03
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $10.44
Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.
$79.80
Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier. Key benefits Softens cured silicone and many common sealants to aid scraping and removal Helps break down adhesive residue, tapes and grime build-up Non-drip gel action for vertical joints, corners and trims Low mess application with excellent wetting of tight gaps Preps surfaces for fresh re-sealing and re-bonding Where to use Bathrooms: around showers, baths, basins and splashbacks Kitchens and laundries: benchtop perimeters, sinks and tiles Windows and doors: frames, trims and glazing edges Suitable substrates Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals Some plastics and laminates (always test first in an inconspicuous spot) Not recommended on Natural stone, marble or porous tiles Freshly painted, delicate or lacquered surfaces Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics Directions Cut away and remove as much old sealant as possible with a plastic scraper. Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue. Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness. Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots. Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing. Pro tips Score thick beads along the edges with a utility blade before application to help penetration. Work in manageable sections and avoid letting the remover dry on the surface. Always test on a small hidden area to check surface compatibility. Safety Use in a well ventilated area and wear gloves and eye protection. Avoid contact with skin and eyes. Keep out of reach of children. Product details Brand: Selleys Type: Sealant and adhesive remover Pack size: 375g
$38.69
Bostik Hard Plastics Glue is a clear, fast-setting adhesive designed for rigid plastic repairs around the home, garage, and workshop. It forms a strong, durable bond that resists impacts and everyday handling while drying clear for a neat finish. Best for ABS, PVC, acrylic, polycarbonate, polystyrene Household repairs, toys, car trim, appliance covers Small craft fixes and model making Not suitable for Polyethylene or polypropylene PTFE or silicone surfaces Surfaces that are oily, dusty, or wet Key features Clear finish that blends with most plastics Fast initial grab with strong final cure Impact and vibration resistant Precision nozzle for controlled application Surface preparation Ensure surfaces are clean, dry, and free from dust, grease, or release agents. Lightly roughen glossy plastic with fine sandpaper to improve adhesion, then wipe clean. How to use Test on a small hidden area first. Apply a thin, even layer to one surface. Avoid excess. Join parts immediately and hold firmly for 30 to 60 seconds. Allow to set undisturbed. Handling strength is typically reached within minutes. Full cure develops over 12 to 24 hours depending on temperature and humidity. Tips For tight fitting parts, less is more. A thin film gives the strongest bond. Use clamps or tape to maintain alignment while the adhesive sets. Cleanup Wipe fresh adhesive immediately with a suitable solvent on a cloth. Cured residue may need careful mechanical removal. Storage and safety Replace cap after use and store upright in a cool, dry place. Use in a well ventilated area. Avoid skin and eye contact. Keep out of reach of children.
$12.72
Tarzan’s Grip Super Glue is a fast-setting cyanoacrylic acid ester based adhesive. Tarzan's Grip Super Glue dries colourless. Special multi-purpose formula allows product to bond to a variety of surfaces Quick-setting Dries clear, therefore no mess
$6.06
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes. Easy mix Durable bond Dries clear Water resistant
$13.39
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$15.39
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$24.57
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins Limitations: +Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
$21.93
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$32.40
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.78
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$8.40
Multi-Purpose Cleaner and Deodorizer Natural Minerals easily dissolve in water Directions: Test on an inconspicuous area first Borax can be used in powder form for tea and coffee cup stains General cleaning 1-table spoon to 4.5 Litres of warm water (also woollens and blankets) Enamel surfaces 4 tablespoons to 4.5 Litres of warm water (refrigerators, stoves, sinks, baths & tiles Uses: General cleaning, stain remover, deodorizer
$9.47
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$10.04
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$14.99
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$9.53
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
Gorilla Clear Grip® is a flexible, fast-setting, crystal clear contact adhesive that creates a strong, permanent bond. Gorilla Clear Grip® is paintable and waterproof making it great for projects both inside and out! Build, Repair, Craft™ PRODUCT FEATURES WATERPROOF – For indoor/outdoor use FAST GRAB – Holds in just seconds PERMANENT BOND FLEXIBLE CRYSTAL CLEAR HEAVY DUTY NO-RUN FORMULA PAINTABLE PHOTO SAFE WASHER & DRYER SAFE BONDS: Metal, Glass, Fabric, Wood, Ceramic, Leather, Paper, Plastic*, and More! *Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. All surfaces should be clean and free of dirt, grease and oil. Best if used between 10°C and 32.2°C. Clear Grip® should only be used in a well ventilated area. Apply adhesive to each surface to be bonded. To maximize bond strength: Wait approximately two minutes for adhesive to partially dry before joining surfaces. Press surfaces firmly together. NOTE: Bond forms immediately and can be difficult to reposition. Cure Time Allow for a minimum of 24 hours for full cure. Cure time may increase with lower temperatures and when used on non-porous surfaces. Storage Tips After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. Store away from children and animals. Clean-up Wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. Paintable When fully cured. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. TECHNICAL SPECS APPLICATION TEMPERATURE – 10° to 32.2° C, best at room temperature OUTDOOR – Yes MOISTURE RESISTANT – Waterproof PAINTABLE – Yes – Can be painted with water and oil based paints, spray paint SANDABLE – Yes STAINABLE – Yes CURED COLOR – Clear STORAGE TIPS – Flammable adhesive, do not use or store near heat, sparks, flames, or while smoking. Store in a cool, dry location. Wipe nozzle clean before replacing cap, for easy re-open apply a thin coat of petroleum jelly to threads. GAP FILLING – No PHOTO SAFE – Yes WASHER & DRYER SAFE – Yes How should Gorilla Clear Grip® be stored? After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. What surfaces does Clear Grip® adhere to? Gorilla Clear Grip® can be adhered to many surfaces including: Wood, Metal, Stone, Ceramic, Glass, Plastic*, PVC, Brick, Concrete, Foam, Paper, Rubber, Fabric, and Laminate. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. Is Gorilla Clear Grip® food safe? Clear Grip® should not be used around food. How do you clean up Gorilla Clear Grip®? When using Clear Grip®, it is best to wear safety glasses and chemical resistant gloves. To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. See first aid treatment for skin contact. Is Gorilla Clear Grip® gap filling? No Is Gorilla Clear Grip® UV Resistant? Yes Can Gorilla Clear Grip® be used both indoors and outdoors? Yes, Gorilla Clear Grip® can be used both indoors and outdoors. Is Gorilla Clear Grip® stainable? Yes, Gorilla Clear Grip® is stainable when fully cured. Is Gorilla Clear Grip® sandable? Yes, cured Gorilla Clear Grip® is sandable. Is Gorilla Clear Grip® paintable? Yes, when fully cured. Is Gorilla Clear Grip® Washer/Dryer safe? Yes Is Gorilla Clear Grip® photo safe? Gorilla Clear Grip® is safe to use with photos.
$15.72
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$19.89
APPLICATION 1. Pierce seal at end of tube by turning nozzle and cap clockwise. 2. Ensure the working surface is clean, dry, free of dust or any grease. 3. Apply adhesive sparingly to one surface only. 4. Place surfaces together and press firmly for 10 - 60 seconds. Adequate for practical purposes after 30 minutes STORAGE: 5. After use. clean nozzle immediately with a cloth, replace cap and store upright between 5- 25°C. Avoid strong light and heat sources LIMITATION: Not recommended for polyethylene, polyester plastic & glass. Not suitable for use on items which contain hot liquids eg. Cups, mugs. May cause leather to discolour or harden. Test on a hidden area before use if in doubt. For interior use only.
$6.50
Overview Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free! Features Automatic Self-Mixing Nozzle No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance. Fast Setting & Long-Lasting Sets in just 5 minutes. Can be safely handled within 30 minutes. Attains full strength after 16 hours. Versatile Usage Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects. Superior Formulation 50% Epoxy Resin 50% Modified Amine Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C. How to Use Preparation Safety First: Always wear protective gloves and safety glasses. Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease. Application Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully. Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener. Mixing: Mix thoroughly before applying. Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary. Post-Application Cleanup: Use acetone for cleaning. Storage: Store in a cool, dry place with the nozzle end up.
$9.95
High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg
$49.42
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$77.97
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
Dunlop Ready-to-Go Tile & Grout 250g (White) is a clever 2-in-1 product that works as both a tile adhesive and a grout, straight from the tube. There is nothing to mix and very little mess, which makes it a go-to for small tiling jobs, mosaics and quick repairs or touch-ups around the home. Backed by Dunlop's 10 year guarantee. 2-in-1 ready-to-use tile adhesive and grout No mixing, no fuss, less mess Contains Grout Shield antifungal protection Ideal for mosaics, repairs and touch-ups Suitable for joint widths of 1-5 mm Indoor and outdoor wall use About the formula This white, pre-mixed paste bonds wall tiles and then fills the joints with the same material, so a single tube handles the whole repair. The built-in Grout Shield technology helps resist mould and bacteria, keeping finished joints looking cleaner for longer. Excess can simply be wiped away with a damp cloth while still fresh, and the resealable tube makes it easy to store for future touch-ups. Where to use it Indoors: wall tiles and mosaics in kitchens, splashbacks, laundries and living areas, plus general tile and grout repairs. Suitable over concrete, cement render, fibre-cement sheet, plasterboard and prepared painted surfaces. Outdoors: exterior wall tiles and mosaics. When grouting outdoors, protect the area from extremes of weather for 7 days while it cures. Tile types: ceramic, porcelain and marble wall tiles and mosaics (excluding moisture-sensitive stone). How to use it Prepare the surface so it is flat, firmly fixed, clean and dry, free of dust, oil, grease and loose material. Prime surfaces with Dunlop Primer & Additive and allow to dry. Spread the adhesive with a 4.5-6 mm notched trowel to a minimum 1 mm bed. Press and slide each tile into position for full contact, adjusting within 60 minutes (at 23°C, 50% humidity). Joints can be grouted immediately. Squeeze the material firmly into the joints and compact with a grout float or squeegee, scraping off excess from the tile face. After about 15 minutes, wipe back excess with a damp, small-pored sponge, rinsing often. Once the joint has hardened (approx. 6-24 hours), buff and polish the tiles with a clean, dry cloth. Important notes Not suitable for use in wet areas such as a shower recess, over Dunlop Waterproofing membrane, or in continuously immersed conditions. Do not use the grout in expansion or movement joints. For textured or matt tiles, test ease of cleaning on a spare tile first. Designed for wall tiles and mosaics rather than heavy floor tiling. Specifications Brand Dunlop Product Ready-to-Go Tile & Grout (2-in-1) Colour White Size 250 g Form Pre-mixed, ready-to-use paste Tile types Ceramic, porcelain, marble, mosaics (excl. moisture-sensitive stone) Surfaces Walls Location Indoor and outdoor Joint width 1-5 mm Clean up Water (while fresh) Guarantee 10 year (Ardex Australia) Safety Causes skin irritation and may cause an allergic skin reaction. Causes serious eye damage and may cause respiratory irritation. Use only outdoors or in a well-ventilated area, and wear protective gloves, clothing, eye and face protection. Avoid breathing any mist, vapour or spray. If in eyes, rinse cautiously with water for several minutes, remove contact lenses if easy to do, and seek immediate medical advice. If on skin, wash with plenty of water and remove contaminated clothing. If inhaled, move the person to fresh air. Store locked up and keep out of reach of children. Always read the current Safety Data Sheet before use.
$16.88
Selleys Araldite Ultimate Bond is a grey two-part epoxy adhesive engineered for the most demanding repairs, delivering a durable, long-lasting bond that holds up to 200kg/cm² when fully cured on stainless steel. It is the toughest of the Araldite range, designed to be tug and snap proof for fixes that need to stay put. About this adhesive Two-part system of resin (Part A) and hardener (Part B) mixed in a 2:1 ratio. Bonds a wide range of surfaces with a strong, rigid, durable join. Sets in around 5 minutes and is touch-firm fast, with a low-odour formula. Made from 20% bio-based carbon. Working (usable) time of roughly 3-4 minutes at 20°C, so mix only what you can apply. What it bonds China, ceramic and porcelain Metal Glass Leather (pre-test for compatibility) Rubber (pre-test for compatibility) Wood and timber Most rigid plastics Where to use it Indoor: repairing crockery, ornaments and ceramics, refitting loose furniture joints, bonding metal, glass and timber components, and general household fixes. Outdoor: durable repairs on tools, garden and workshop items where a tough, weather-durable bond is required. Bond strength depends on substrate, bond size and surface preparation, and set times lengthen in colder weather. How to use it 1. Abrade, clean and dry both surfaces so they are free of dust, grease and loose oxides. 2. Snap the cap from the plunger and carefully cut the sealed tips at the end of the nozzle. 3. Apply even pressure to the plunger to dispense both liquids onto a clean disposable surface (2:1 ratio) and mix thoroughly with a spatula. 4. Apply the mixed glue to both surfaces, then bring them together. 5. Hold in place with tape or weights if needed and avoid undue strain on the joint for at least 60 minutes. Cures in 24 hours; maximise the bond area (minimum 2.25cm²) for best performance after full cure. Replace the cap on the nozzle for storage and clean up any uncured adhesive with acetone. Important notes Will not bond PTFE, polyethylene or polypropylene plastics. Bond will soften above 60°C but strength is restored once the temperature returns to normal. May discolour if exposed to UV. Full cure takes more than 72 hours. Not recommended where a clear, invisible bond is required, as the cured adhesive is grey. Specifications Brand Selleys Araldite Product Ultimate Bond Epoxy Adhesive Technology Two-part epoxy Colour Grey Size 30mL Mix ratio 2:1 (Part A : Part B) Working time Approx. 3-4 minutes at 20°C Set time Approx. 5 minutes Cure time 24 hours (full cure >72 hours) Holds Up to 200kg/cm² on stainless steel when fully cured Heat resistance Softens above 60°C, strength restored on cooling Clean up Acetone (while uncured) Safety Danger. Part A causes skin and serious eye irritation and may cause an allergic skin reaction. Part B may be corrosive to metals, causes severe skin burns and eye damage, and may cause an allergic skin reaction. Do not swallow and avoid contact with skin and eyes. Wear eye protection and protective gloves when mixing or using, and avoid breathing dust, vapours or spray. Keep out of reach of children and keep in the original packaging. If medical advice is needed, have the product container or label at hand. Refer to the Safety Data Sheet for full handling information.
$26.99
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened Safety Contains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. For eye contact, rinse with water for 15 minutes and seek medical advice. If swallowed, do not induce vomiting and seek medical advice. Keep out of reach of children. Always refer to the Safety Data Sheet before use.
$33.75
Glitz Borax is a versatile cleaner and laundry booster that tackles grime, helps remove stains, and deodorises around the home. This mineral based powder dissolves in warm water to lift dirt, cut through residues, and freshen hard surfaces and fabrics. Why you will love it Multi purpose performance for laundry, kitchen, and bathroom Helps remove tough stains and lingering odours Boosts detergent effectiveness in hard water Deodorises bins, drains, and pet areas Free from added fragrance and chlorine Where to use Laundry booster for everyday washing Tiles, grout, sinks, and benchtops Toilets and bathroom surfaces Bins, outdoor furniture, and patios General deodorising tasks How to use Laundry booster: Add 1 to 2 tablespoons to the wash with your usual detergent. For heavily soiled loads use up to 1/4 cup. Dissolve in warm water for best results. Multi surface cleaner: Dissolve 2 tablespoons in 1 litre of warm water. Wipe surfaces with a cloth or sponge. Rinse food contact areas with clean water after cleaning. Stain pre soak: Dissolve 2 tablespoons in 2 litres of warm water. Soak colourfast fabrics for up to 30 minutes. Rinse well before washing as normal. Always patch test first. Deodorising paste: Mix borax with a little water to form a paste. Apply to tiles or grout, lightly scrub, then rinse. Bin and drain freshen: Sprinkle 2 to 3 tablespoons in the bin base or dissolve in warm water and flush down the drain. Rinse thoroughly. Good to know Use on sealed hard surfaces only Check fabric care labels and test on a hidden area first Not suitable for wool, silk, leather, or aluminium What is in the pack Glitz Borax powder 1 kg resealable pack Specifications Product type Multi purpose cleaner and laundry booster Form Free flowing powder Size 1 kg Fragrance None added Safety and storage Read and follow the label before use Wear gloves for prolonged contact Avoid inhaling dust. Use in a well ventilated area Keep out of reach of children and pets Do not ingest. Do not use on skin or as a personal care product Store in a cool dry place with the pouch sealed Disposal Rinse empty packaging and dispose of it in accordance with local council guidelines. Frequently asked questions Can I use it in cold waterYes, but it dissolves more readily in warm water. Pre dissolve in a small amount of warm water when using cold cycles. Is it safe for septic systemsUse sparingly and flush well with plenty of water. Follow any appliance and system guidelines. Will it bleach coloured fabricsIt does not contain chlorine bleach. Always check colourfastness and test on a hidden area first.
$12.22 $9.45
Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L is your everyday helper for a fast, streak free clean. Spray, wipe, and enjoy a bright finish on benches, tables, appliances, and other sealed surfaces around the home. Why you will love it Cuts through daily grime and light grease with ease Leaves a streak free shine on most sealed surfaces Fresh, clean household scent that does not linger No rinsing required on lightly soiled areas Ready to use for quick jobs or dilute for larger areas to save cost Best for Kitchen benches, tables, cupboards, splashbacks Bathroom vanities, tiles, taps, glass shower screens outside surface only Door handles, light switches, appliances exterior, bins Floors when diluted in a bucket for general freshen ups Do not use on Unsealed or waxed timber Natural stone that is unsealed or acid sensitive such as marble and limestone Screen displays or electronics Delicate finishes. Always spot test in a hidden area first How to use Light cleaning. Spray directly onto the surface and wipe with a clean cloth Heavier soil. Let sit for 30 to 60 seconds then wipe. Repeat if required Floors. Add 60 to 100 ml per 5 L of warm water, mop, then allow to dry Glass and glossy areas. Use a lint free cloth and buff dry for best results Quick tips Use separate cloths for kitchen and bathroom to avoid cross contamination For stainless steel, always wipe with the grain and finish with a dry cloth On painted surfaces, apply to cloth first, not directly to the wall Specifications Brand Glitz Product Domestic Cleaner Multi Purpose Surface Shine Format Ready to use liquid. Dilutable for floors Pack size 1.25 L bottle Fragrance Fresh household scent Surface compatibility Most sealed hard surfaces including laminates, sealed stone, ceramic tile, porcelain, stainless steel, enamel, and sealed timber Country of use Suitable for Australian homes and water conditions What is in the box 1 x Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25 L Storage and safety Store upright in a cool, dry place away from direct sunlight Keep out of reach of children and pets Avoid contact with eyes. If in eyes rinse with water Do not ingest. If swallowed seek medical advice Frequently asked questions Can I use it on food contact areas Yes. Clean the surface, then wipe with a damp cloth and allow to dry before food preparation Will it leave residue No when used as directed. Buff with a dry cloth on glass or glossy areas for a crystal finish Is rinsing required Not for light soil. For heavy soil or floors, rinse the mop head regularly for best results Good to know Ideal for quick daily resets in kitchens and bathrooms Economical size that suits family households and shared spaces
$6.51 $6.04
You have seen 96 out of 158 products
Clear and structural options for ceramic and porcelain repairs or installations. For small chips and breaks, consider cyanoacrylates and epoxies; for wet areas, select waterproof and non-corrosive formulas. Check temperature resistance for cookware and ensure full cure before service. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
