Dunlop Ardit Construction Grout is a high-strength, cement-based grout that can be mixed to either a stiff, paste-like consistency or a free-flowing pour, making it a genuine all-rounder for construction and repair work. Formulated with Ardit Technology and an extended working time, it gives you more room to position components accurately before the mix begins to set. This non-shrink formulation reaches approximately 45MPa after 7 days and around 65MPa at 28 days, and it is backed by a 10 year guarantee. The handy 5kg bag suits smaller jobs and repairs without the waste of a full-size bag.Where to use itSuitable for indoor and outdoor projects wherever a high-strength, non-shrink grout is required — general construction grouting, machine and equipment base grouting, filling voids and pockets in concrete, bedding and packing under plates, and anchoring bolts, rails and posts. It performs over concrete and masonry substrates at application thicknesses from 5mm up to 100mm.How to usePrepare a sound, clean substrate free of dust, oil and loose material, and pre-dampen absorbent surfaces. Mix the powder with clean water to the consistency the job calls for — non-slump paste for vertical packing or a flowable mix for pouring into forms and voids. Place the grout within its working time, compacting or rodding to remove air pockets, then finish with a trowel. As a guide, a 20kg quantity yields roughly 11.2L as a non-slump mix or 12.0L as a flowable mix, so expect around a quarter of that from this 5kg bag.Important notesApply between 5mm and 100mm thickness. Do not over-water the mix, as excess water reduces final strength. Cold or damp conditions extend curing times; hot, windy conditions shorten working time.Specifications Size 5kg bag Colour Grey Yield Approx. 2.8-3.0L per 5kg depending on consistency Compressive strength Approx. 45MPa (7 days), 65MPa (28 days) Application thickness 5-100mm SafetyContains cement — the wet mix is alkaline and can irritate skin and eyes. Wear gloves, safety glasses and a dust mask when handling the dry powder, work in a ventilated area and wash hands after use. Refer to the Safety Data Sheet before use and keep out of reach of children.
$23.73
Dunlop Universal Tile Adhesive is the do-almost-anything adhesive in the Dunlop Trade (ARDEX Australia) range – a high performance, multipurpose wall and floor tile adhesive with excellent workability and flexibility. Its non-slumping formula keeps wall tiles in position while its C2TES1 classification delivers extended open time, slip resistance and a deformable, high-strength bond for demanding applications.Where to use itOne of the most versatile adhesives available: suitable for indoor and outdoor walls and floors, and even swimming pools. It fixes ceramic, porcelain, natural stone (excluding moisture sensitive stone), mosaics and fully vitrified tiles over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render.How to useMix with clean water to a smooth, creamy consistency and allow to stand briefly before a final remix. Apply to a clean, dry, sound substrate with a 6mm notched trowel on walls or a 10mm notched trowel on floors. Press tiles firmly home with a twisting action, ensuring good adhesive transfer to the tile back – especially important outdoors and in pools where full contact is required. Grout after approximately 24 hours at 23°C and 50% relative humidity.Important notesNot suitable for moisture sensitive natural stone. For pool installations, allow the full recommended cure before filling. The product exceeds ISO 13007 requirements.Specifications Size 20kg bag Colour White Coverage 11m² per 20kg (6mm trowel); 7m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, non-sensitive stone, mosaics, fully vitrified Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2TES1 tile adhesive; exceeds ISO 13007 SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection while mixing and applying, and work in a well-ventilated area. Refer to the safety data sheet before use.
$59.68
Dunlop Artificial Grass Adhesive is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia), purpose-made for laying artificial grass, outdoor carpet and marine carpet. With excellent water and heat resistance and a bond that stands up to sun, rain and foot traffic, it is the reliable way to keep synthetic turf flat and secure – and it is backed by a 10 year guarantee. This handy 1 litre can is ideal for smaller lawns, edges, joins and repair work.Where to use itDesigned primarily for outdoor projects such as synthetic lawns, pool surrounds, balconies, courtyards and boat decks, and equally suitable for indoor applications like covered patios and utility areas. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to useEnsure the surface is clean, dry and free of dust, oil and loose material. Spread the adhesive evenly with a suitable notched spreader or trowel at approximately 3m² per litre, then lay the grass or carpet into the wet adhesive, smoothing outwards to remove air pockets. Weight or roll the surface while the adhesive develops strength and avoid heavy traffic until fully cured.Important notesDo not apply in extremely hot or cold conditions – work between 10°C and 30°C – and never apply when dew or rain is imminent, as moisture can affect bond development before cure.Specifications Size 1 litre can Colour Green Coverage Approx. 3m² per litre Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: use only in well-ventilated areas, keep away from heat, sparks and open flames, and avoid breathing vapours. Wear gloves and eye protection, replace the lid when not in use and keep out of reach of children. Refer to the safety data sheet before use.
$35.99
Dunlop Trade Resaflex is a multipurpose, rubber modified tile adhesive from Dunlop Trade (ARDEX Australia), trusted by professional tilers for decades. Its rubber modified cement formulation delivers a strong yet flexible bond that tolerates normal building movement, and its C2S1 classification confirms improved adhesion and deformability. One bag covers a wide range of everyday tiling jobs, which is exactly why it has earned its multipurpose name.Where to use itSuitable for indoor and outdoor walls and floors. Use it to fix ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can also be used over Dunlop Waterproofing and green screed, making it well suited to bathrooms and new-build wet areas.How to useMix the powder with clean water to a smooth, lump-free paste. Spread onto a clean, dry, sound substrate with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles. Bed each tile with a firm twisting action to achieve full contact, and lift a tile occasionally to check coverage. Allow the adhesive to cure before grouting.Important notesNot suitable for moisture sensitive natural stone. Only mix what can be used within the working time and never re-temper stiffened adhesive with extra water.Specifications Size 20kg bag Colour Grey Coverage 0.65m²/kg (6-8mm trowel); 0.4-0.5m²/kg (10-12mm trowel) Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, waterproofing, plasterboard, render Classification C2S1 rubber modified tile adhesive SafetyContains cement. Avoid breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Wash skin after handling and refer to the safety data sheet before use.
$53.15
Dunlop Artificial Grass Adhesive in the value 4 litre can is a high strength, all-weather adhesive from Dunlop Trade (ARDEX Australia) for laying artificial grass, outdoor carpet and marine carpet across larger areas. Formulated with excellent water and heat resistance, it keeps synthetic turf and outdoor floor coverings firmly bonded through harsh Australian conditions, and is backed by a 10 year guarantee. At roughly 3m² per litre, one 4L can covers around 12m² – ideal for full lawns, entertaining areas and commercial installs.Where to use itBuilt for outdoor projects – synthetic lawns, pool surrounds, balconies, rooftops, courtyards and marine decks – and also suitable for indoor areas such as covered patios. It bonds securely to concrete, clean paved surfaces, suitably prepared metal, sanded fibreglass and timber.How to usePrepare a clean, dry, dust-free surface. Spread the adhesive evenly using a suitable notched spreader or trowel, working in sections you can cover while the adhesive is wet. Lay the grass or carpet into the adhesive, smooth outwards to expel trapped air, then roll or weight the surface. Keep traffic off until the adhesive has fully cured.Important notesDo not use in extremely hot or cold conditions – apply between 10°C and 30°C – and do not apply when dew or rain is expected before the adhesive has set. Ensure joins are well supported and seams glued continuously for a lasting result.Specifications Size 4 litre can Colour Green Coverage Approx. 3m² per litre (about 12m² per can) Suitable coverings Artificial grass, outdoor carpet, marine carpet Substrates Concrete, pavers, prepared metal, sanded fibreglass, timber Guarantee 10 year guarantee SafetySolvent-based adhesive: ensure good ventilation, keep away from ignition sources and avoid inhaling vapours. Wear protective gloves and eye protection, reseal the can after use and store away from children. Consult the safety data sheet before use.
$97.56
Dunlop Tiler's Mastic is a premium non-slump tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). Built for the demands of modern tiling, its high-grab, non-slump formula is ideal for today's large format tiles, holding them exactly where you place them on walls while still spreading smoothly and easily on floors. As a C2TES1 classified adhesive it offers extended open time, slip resistance and deformability for a strong, flexible bond.Where to use itSuitable for indoor and outdoor walls and floors, including wet areas over Dunlop Waterproofing. It fixes ceramic, porcelain, non-moisture sensitive natural stone, fully vitrified, mosaic and translucent tiles over cement render, compressed fibre-cement sheet (floors), concrete, Dunlop Undertile Waterproofing, existing ceramic tiles, ceramic tile underlay, fibre-cement sheet (walls) and plasterboard.How to useMix the powder with clean water to a smooth, creamy paste. Trowel onto a clean, dry, sound substrate with a 6 x 6 x 6mm notched trowel for walls or a 10 x 10 x 10mm notched trowel for floors and large tiles. Bed tiles with a firm twisting action, checking contact coverage regularly. Grout after approximately 24 hours.Important notesNot suitable for moisture sensitive natural stone. Ensure substrates are properly prepared and primed where required, and avoid tiling in extreme temperatures.Specifications Size 20kg bag Colour White Coverage 10m² with 6mm notched trowel; 6m² with 10mm notched trowel Tile types Ceramic, porcelain, non-sensitive stone, vitrified, mosaics, translucent Substrates Render, concrete, compressed FC sheet, waterproofing, existing tiles, plasterboard Classification C2TES1 tile adhesive SafetyContains cement – avoid breathing dust and avoid skin and eye contact. Wear protective gloves, clothing and eye protection, and mix in a well-ventilated area. Consult the safety data sheet before use.
$40.28
Dunlop Tiler's Rubber Modified is a flexible, rubber modified tile adhesive for walls and floors from Dunlop Trade (ARDEX Australia). The rubber modified formulation gives the cured bond extra flexibility to absorb normal substrate movement, while its generous coverage and 6-hour grout time keep jobs moving. Classified C2S1, it is a dependable workhorse for tilers who need strength, flexibility and speed in one bag.Where to use itSuitable for indoor and outdoor walls and floors. It fixes ceramic tiles, fully vitrified tiles, mosaics, porcelain and natural stone (excluding moisture sensitive stone) over compressed fibre-cement sheet floors, concrete floors, ceramic tile underlay, fibre-cement sheet walls, Dunlop Undertile Waterproofing, plasterboard and render. It can even be used over Dunlop Waterproofing and green concrete, making it handy on fast-track projects.How to useMix with clean water to a smooth, creamy consistency and allow to slake before remixing. Apply to a clean, sound, dust-free substrate using a 6 x 6 x 6mm notched trowel on walls or a 10 x 10 x 10mm notched trowel on floors. Press tiles in firmly with a twisting action and check adhesive transfer on the tile back. Grouting can begin in as little as 6 hours.Important notesNot suitable for moisture sensitive natural stone. Do not add extra water once the mix begins to stiffen, and avoid application in extreme temperatures.Specifications Size 20kg bag Colour Grey Coverage 14m² with 6mm notched trowel; 8m² with 10mm notched trowel Tile types Ceramic, vitrified, mosaics, porcelain, non-sensitive natural stone Substrates Concrete, compressed FC floors, FC walls, CTU, waterproofing, plasterboard, render Classification C2S1 tile adhesive; grout in 6 hours SafetyContains cement. Avoid generating and breathing dust, wear protective gloves, clothing and eye protection, and mix in a well-ventilated space. Refer to the safety data sheet before use.
$47.18
Dunlop Super Tileset Plus is a smooth, creamy cement-based wall and floor tile adhesive from Dunlop Trade (ARDEX Australia). Mixing to a workable, easy-spreading consistency, it delivers dependable adhesion for everyday tiling at an economical price, making it a solid choice for renovators and trade users tackling standard wall and floor jobs.Where to use itApproved for both indoor and outdoor use on walls and floors. It suits bathrooms, kitchens, laundries, living areas and patios, and bonds ceramic, porcelain, mosaics, fully vitrified, translucent tiles and natural stone (excluding moisture sensitive stone) over concrete, render, screeds, Dunlop Waterproofing Membranes, fibre-cement sheets and plasterboard.How to useMix the powder with clean water to a smooth, lump-free paste and allow it to stand briefly before remixing. Spread onto a clean, dry, sound substrate with a 6mm notched trowel for walls and smaller tiles, or a 10mm notched trowel for floors and larger formats. Bed tiles firmly with a twisting action and check coverage on the tile back periodically. Grouting can proceed after approximately 24 hours at 23°C and 50% relative humidity.Important notesDo not tile over moisture sensitive natural stone with this adhesive, and avoid tiling in extreme temperatures or onto frozen or saturated substrates. Only mix as much adhesive as can be used within its working time.Specifications Size 20kg bag Colour Off-white Coverage 9m² per 20kg (6mm trowel); 6m² per 20kg (10mm trowel) Tile types Ceramic, porcelain, mosaics, vitrified, translucent, non-sensitive stone Substrates Concrete, render, screeds, Dunlop membranes, FC sheet, plasterboard Classification Exceeds C1 Australian Standard SafetyContains cement. Avoid breathing dust and avoid contact with skin and eyes – wear protective gloves, clothing and eye protection when mixing and applying. Mix in a well-ventilated area and refer to the safety data sheet before use.
$36.00
Dunlop Wall & Floor Tile Adhesive is a high performance, ready-mixed adhesive from Dunlop Trade (ARDEX Australia) that takes the hassle out of fixing most tile types. Supplied in an easy-to-handle 8kg pail, it is specially formulated to bond ceramic, porcelain, mosaics, fully vitrified tiles and natural stone (excluding moisture sensitive stone), and its highly flexible formulation copes with the small movements that occur in everyday walls and floors.Where to use itSuitable for indoor walls and floors, and outdoor areas provided there is no standing water and sufficient fall for run-off. It bonds over an impressive range of surfaces: cement render and concrete, fibre-cement sheets, existing ceramic and vinyl tiles, Dunlop Undertile Waterproofing, prepared metal surfaces, oil-based painted surfaces, plasterboard and suitably prepared interior timber.How to useMake sure the substrate is clean, dry and free of dust or grease. Spread the adhesive with a 6-8mm notched trowel for tiles up to 250 x 250mm, or a 10-12mm notched trowel for larger tiles, then bed tiles in firmly with a twisting motion. Work in small sections so a skin does not form before tiling.Important notesDo not use over strip timber floors. Prime particleboard and plywood sheet floors with Dunlop Tile-All before tiling. For fully immersed or pool applications choose a cement-based Dunlop adhesive instead.Specifications Size 8kg pail Colour Grey Coverage 0.8m²/kg (6-8mm trowel); 0.5m²/kg (10-12mm trowel) Tile types Ceramic, porcelain, mosaics, fully vitrified, natural stone (non moisture sensitive) Substrates Concrete, render, FC sheet, existing tiles, vinyl, metal, plasterboard, prepared timber Format Premixed dispersion adhesive SafetyWork in a well-ventilated area, wear gloves and eye protection, and avoid prolonged skin contact. Wash tools and hands with water before the adhesive dries. Keep out of reach of children and consult the SDS before use.
$93.46
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.
$43.00
Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.
$313.95
Dunlop Rapid Bond Coat is a water-based bonding coat that creates a chemical key on smooth, dense, non-porous surfaces, the ones ordinary primers struggle to grip. Applied before Dunlop adhesives, floor levelling compounds or Dunlop undertile waterproofing membranes (in non-immersed situations), it transforms slick substrates such as glazed tiles into a surface your next product can actually hold onto. It is the product that makes tile-over-tile renovations possible without demolition, and its rapid-drying formula keeps the job moving.Where to use itSuitable for indoor and outdoor use on walls and floors. Use it over glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement and compressed fibre-cement sheet, Scyon and internal sheet timber.How to useClean the surface thoroughly, degreasing glazed or dense substrates so nothing interferes with the bond. Apply a thin, even coat by brush or roller and allow it to dry before applying your adhesive, leveller or membrane. Being water-based, wet product cleans off tools with water.Important notesRapid Bond Coat is designed for smooth, dense and difficult non-porous substrates; for ordinary porous surfaces use Dunlop Multipurpose Primer instead. When used under waterproofing it is for non-fully-immersed applications only. Coverage varies with the substrate and application method.Specifications Size 1 litre Coverage Approx. 10m² per litre Substrates Glazed tiles, concrete, renders, screeds, masonry, AAC block, fibre-cement, Scyon, internal sheet timber Drying Rapid drying SafetyVentilate the room, wear gloves, and avoid contact with eyes and skin. Store the sealed bottle away from children and check the Safety Data Sheet before use.
$67.73
Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.
$142.94
Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.
$60.26
Dunlop Ardit Crack Filler is a high strength, two-part hybrid polyurethane that repairs cracks and spalls in concrete almost instantly. With a viscosity similar to water, it flows deep into cracks that pastes and mortars can't reach, then cures harder than the surrounding concrete within an hour. Driveable repairs are possible in as little as 20 minutes, making it a genuine problem-solver for busy floors and driveways.Where to use itSuitable for indoor and outdoor concrete - garage floors, driveways, paths, warehouse slabs and patios. Because the two parts mix automatically through the nozzle, it is equally at home in a professional toolkit or a weekend repair kit.How to useClean the crack thoroughly, removing dust, loose material and any moisture. Load the 254ml dual cartridge into a suitable applicator gun, attach the self-mixing nozzle and dispense directly into the crack until full. For wider spalls and larger repairs, blend in clean, dry bagged aggregate to bulk the fill. The repair sets stronger than concrete in about 1 hour and takes vehicle traffic after roughly 20 minutes.Important notesNew concrete must be fully cured - at least 28 days old - before application. The water-thin consistency is designed for penetrating cracks, so dam or tape the ends of through-cracks where needed. Used nozzles cannot be reused once the product sets.Specifications Size 254ml dual cartridge Coverage Depends on crack width and depth Thickness Flows to full crack depth; add aggregate for large voids Substrates Concrete Set time Drive on after 20 minutes; full strength in 1 hour SafetyReactive polyurethane resins can irritate skin and airways before curing. Wear nitrile gloves and safety glasses, work in a well-ventilated area, avoid skin contact with uncured product and keep it away from children. Dispose of cartridges according to local regulations.
$67.48
Dunlop Builder's Bond is a high strength, multipurpose, rapid-cure epoxy bonding and repair system that joins almost any building material to almost any other. Dispensed through a self-mixing nozzle from a convenient 254ml dual cartridge, its non-sag formula holds firm on walls and even overhead, and cures stronger than concrete in about 2 hours.Where to use itSuitable for indoor and outdoor use across floor, wall and overhead repairs. Typical jobs include bonding concrete, masonry, stone, metal and timber components, rebuilding broken edges and corners, anchoring fixtures, and general structural gap filling where a fast, very strong bond is required.How to useEnsure both surfaces are clean, dry and free of dust, grease and loose material. Load the cartridge into an applicator gun, fit the self-mixing nozzle and dispense the evenly mixed epoxy directly onto the repair or bond line. Shape and tool it before it stiffens. Once cured, Builder's Bond can be shaped, sanded, drilled and painted, so repairs can be blended invisibly into the surrounding surface.Important notesNew concrete must be fully cured - a minimum of 28 days old - before bonding. The non-sag consistency suits vertical and overhead work but is not a pourable grout. Start a fresh nozzle for each session, as mixed product hardens inside the nozzle.Specifications Size 254ml dual cartridge Coverage Depends on bead size and gap width Substrates Concrete, masonry, stone, metal, timber and most building materials Set time Stronger than concrete in 2 hours Finish Sandable, drillable and paintable once cured SafetyUncured epoxy resins and hardeners can cause skin irritation and sensitisation. Wear nitrile gloves and eye protection, ventilate the work area, avoid skin contact and wash immediately if contact occurs. Keep cartridges sealed and out of reach of children.
$61.79
Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.
$34.59
Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.50
Dunlop Ardit Feather Finish is a cement-based smoothing compound that skims internal floors to a super-smooth, permanent finish before floor coverings are installed. Powered by ARDEX Ardit technology, it trowels out to a true feather edge and sets so fast that coverings can be applied from just 15 minutes after placement - and it needs no primer on most surfaces, saving a whole step.Where to use itFor indoor use over concrete, existing tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. It is ideal for filling grout joints when covering old tiles with vinyl, smoothing trowel marks in levellers, and taking out minor imperfections before vinyl, carpet or ceramic tiles.How to useEnsure the floor is clean, sound and free of dust, grease and loose material. Mix the powder with clean water to a smooth, creamy paste and apply with a flat steel trowel, working from a feather edge up to 3mm thick. Tight second coats can be applied as the first firms. Any ridges can be shaved or lightly sanded once set for a flawless surface.Important notesIndoor use only and must be covered by a floor covering. Mix small batches to suit the rapid set. No primer is required over common substrates - check the datasheet for unusual surfaces.Specifications Size 3.5kg bag Coverage Approx. 12m² over concrete or 24.5m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyCement powders can irritate eyes, skin and lungs. Wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated, avoid prolonged contact with the wet compound and wash hands after use. Store out of reach of children.
$82.46
Dunlop Ardit Feather Finish in the larger 8kg bag is the go-to smoothing compound for flooring installers tackling bigger areas. This cement-based skimcoat, built on ARDEX Ardit technology, glides out to a genuine feather edge and produces a hard, super-smooth, permanent finish that floor coverings can be laid over from just 15 minutes after application - with no primer required on most substrates.Where to use itFor indoor floors over concrete, existing ceramic tiles, sheet timber (plywood and particleboard) and cured Dunlop floor levellers. Use it to fill grout joints before laying vinyl over tiles, erase trowel marks and minor undulations, and fine-tune levelled floors before vinyl, carpet or new tiles.How to useStart with a clean, sound, dust-free floor. Mix with clean water to a smooth, lump-free paste and spread with a flat steel trowel from a feather edge up to 3mm thick. Because it sets rapidly, mix quantities you can place within a few minutes and apply successive tight coats as needed. Light sanding or shaving once set removes any ridges for a flawless result.Important notesIndoor use only and must be covered by a finished floor covering. The rapid set is a feature - plan batches accordingly. Refer to the technical datasheet for guidance over less common substrates.Specifications Size 8kg bag Coverage Approx. 27m² over concrete or 55m² over sheet timber (skimcoat) Thickness Feather edge to 3mm Substrates Concrete, tiles, sheet timber, Dunlop floor levellers Walk-on time 15-30 minutes; coverings from 15 minutes SafetyWear gloves, safety glasses and a P2 dust mask when handling and mixing the dry powder, ventilate the work area and avoid skin and eye contact with the wet mix. Wash thoroughly after use and keep the bag sealed and away from children.
$125.51
Dunlop Level-Flex Timber Floor Leveller is a high performance, partially self-smoothing latex levelling screed developed specifically for timber floors. Supplied as a complete two-part kit in a handy pail, it combines a cement-based powder with a flexible latex liquid to deliver the adhesion, flexibility and water resistance needed when levelling over floors that move more than concrete does.Where to use itDesigned for indoor use over timber and concrete subfloors, it creates a smooth, flat surface ready for ceramic tiles, carpet or vinyl. It is a popular choice for renovating older homes with uneven timber floorboards or sheet flooring before new coverings are installed.How to useSand and prime timber floors first, and prime porous concrete with a plush broom application. Blend the latex liquid with the powder using a low-speed paddle mixer until smooth, then pour and spread with a trowel, allowing the screed to flow out and self-smooth. The floor is walkable in about 3 hours; lay ceramic tiles after roughly 12 hours (3mm screed), carpet after 24 hours and vinyl after 48 hours.Important notesIndoor use only, and the leveller must be covered by a finished floor covering. Timber must be sound, rigid and well fixed before levelling. Low odour formula makes it comfortable to use in occupied homes.Specifications Size 15.9kg kit (powder plus latex liquid) Coverage Approx. 7m² at 1mm or 2.3m² at 3mm per kit Thickness Feather edge to approx. 12mm (thicker with aggregate) Substrates Timber and concrete Walk-on time 3 hours SafetyWear gloves, safety glasses and a P2 dust mask when handling the cement powder, and keep the room ventilated while mixing. Avoid skin and eye contact with the wet mix, wash after use and store the kit away from children.
$108.45
Dunlop Ardit Timber Floor Leveller is a high performance, partially self-smoothing screed for timber floors, built on ARDEX Ardit technology. Unlike traditional two-part latex levellers, it is a convenient single-part formula - just add water - yet still delivers the excellent adhesion, flexibility and water resistance needed to level over timber substrates that flex underfoot.Where to use itFor indoor use over timber and concrete subfloors, creating a smooth, even base before installing ceramic tiles, carpet or vinyl. It is well suited to renovations where old floorboards or sheet flooring need flattening before new coverings are laid.How to useSand and prime all timber floors before application, and prime porous surfaces such as concrete using a plush broom. Mix the powder with clean water using a low-speed paddle mixer until smooth and lump free, then pour, spread with a trowel and let the screed flow out to a level finish. Apply from a feather edge up to 12mm neat, or up to 30mm with the addition of 2-5mm aggregate.Important notesIndoor use only and must be covered with a finished floor covering. Ensure timber floors are rigid and securely fixed before levelling. The no-odour formula suits occupied homes. Check the technical datasheet for covering wait times for your chosen flooring.Specifications Size 16kg kit Coverage Approx. 10m² at 1mm or 3m² at 3mm per kit Thickness 0-12mm neat; 12-30mm with aggregate Substrates Timber and concrete SafetyThe cement-based powder is alkaline and dusty when dry. Wear gloves, eye protection and a P2 dust mask while mixing, ventilate the work area, avoid contact with skin and eyes, and wash thoroughly after use. Keep away from children and pets.
$105.25
Dunlop Ardit Rapidset Repair Mortar in the 10kg bag gives tradies and serious renovators a bigger supply of this extremely fast-hardening construction mortar. Built on ARDEX Ardit technology, it patches cracks, holes and broken edges and is trafficable after only 45 minutes, with floor coverings able to go down just 1 hour after placement - ideal when repairs can't shut an area down for long.Where to use itUse indoors and outdoors on concrete, render, screeds, masonry, plasterboard, timber and fibre-cement sheet. Typical jobs include patching worn slabs before flooring, building small ramps and transitions, and making good around doors, windows and plumbing work internally.How to usePrepare a clean, sound, dust-free repair area. Mix approximately 3L of clean water with the 10kg of powder to a smooth mortar, then trowel firmly into the repair, compacting well and finishing flush. Apply from a feather edge up to 20mm per pass, building deeper repairs in stages. Working time is about 15 minutes, so mix in manageable batches.Important notesDo not re-temper the mix with extra water once it begins to stiffen. Suited to patch repairs rather than full-floor levelling - pair it with a Dunlop floor leveller for whole-room work. Covered by a 10 year guarantee when used as directed.Specifications Size 10kg bag Coverage Varies with patch depth; feather edge to any thickness Thickness Feather edge up to 20mm per application Substrates Concrete, render, screeds, masonry, plasterboard, timber, fibre-cement Walk-on time 45 minutes (floor coverings after 1 hour) SafetyContains cement - alkaline when wet. Wear gloves, eye protection and a P2 dust mask during mixing, work in a ventilated space, avoid skin contact and rinse any splashes promptly. Keep out of reach of children.
$60.93
Dunlop Ardit Floor Leveller is a premium cement-based levelling compound built on the renowned Ardit Technology from ARDEX. It offers superior flow and workability, spreading easily across uneven concrete to create a smooth, even surface before new floor coverings go down. Floors are walkable in around 3 hours and ready for ceramic tiles in the same timeframe, keeping renovation and re-flooring jobs moving quickly.Where to use itUse indoors and outdoors under covered areas over sound concrete floors, ahead of ceramic tiles, carpet or vinyl. It is designed for concrete substrates only and must be protected by a floor covering rather than left exposed to the weather or used as a finished wear surface.How to useEnsure the slab is clean, sound and primed as required. Mix each 20kg bag with approximately 4.5L of clean water using a low-speed paddle mixer until smooth and lump free. Pour and spread with a trowel, letting the compound flow out and level itself. Apply from a thin skim up to 25mm in one pass, adding 2-5mm aggregate for deeper fills.Important notesNot suitable for driveways or areas subject to vehicular traffic. Vinyl and carpet can be laid after about 24 hours, while tiles can go down after roughly 3 hours. Refer to the technical datasheet for priming guidance on porous slabs.Specifications Size 20kg bag Coverage Approx. 12m² at 1mm or 4m² at 3mm per bag Thickness 1-25mm per application Substrates Concrete Walk-on time 3 hours (tiles 3 hours; vinyl and carpet 24 hours) SafetyContains cement, which is alkaline when wet. Wear gloves, eye protection and a P2 dust mask while mixing, ensure good ventilation, avoid skin contact and rinse promptly if the mix touches skin or eyes. Store away from children.
$67.45
Dunlop Multipurpose Floor Leveller is a cement-based levelling compound from Dunlop Trade (ARDEX Australia) that mixes with water into a smooth, free-flowing material for evening out rough or uneven concrete floors. It flows into low spots and finds its own level, leaving a flat base that is ready for foot traffic in around 2 hours and ready for tiles in about 4 hours, making it a dependable first step before laying new floor coverings such as carpet, vinyl or ceramic tiles.Where to use itSuitable for indoor and outdoor use over sound concrete floors, including living areas, kitchens, laundries and covered patios. It can also be used to form ramps or for bulk filling. It is designed for concrete substrates only and must always be covered by a finished floor covering.How to usePrepare the slab so it is clean, sound and free of dust or contaminants, and prime porous surfaces. Slowly add the powder to clean water while mixing with a low-speed paddle mixer for 2-3 minutes until lump free. Pour onto the floor, spread with a trowel and allow it to self-smooth. Apply up to 25mm in one application, adding 2-5mm aggregate for beds thicker than about 10mm.Important notesNot suitable for driveways or areas with vehicle traffic, and it cannot be left exposed as a wear surface. Sand can be added to create a trowelable screed for ramping. Always follow the technical datasheet for priming and mixing details.Specifications Size 15kg bag Coverage Approx. 1.6kg/m² per mm (about 9m² at 1mm per bag) Thickness Up to 25mm per application Substrates Concrete Walk-on time 2 hours (tiles after 4 hours) SafetyCement-based powders are alkaline and can irritate skin, eyes and airways. Wear gloves, safety glasses and a P2 dust mask when mixing, work in a ventilated area, wash skin after use and keep out of reach of children.
$69.96
Dunlop Ardit Rapidset Repair Mortar is an extremely fast-hardening construction mortar from Dunlop Trade (ARDEX Australia), formulated for patching cracks, holes and damaged sections with minimal downtime. Repairs can take foot traffic after just 45 minutes and accept floor coverings after 1 hour, so a morning patch job doesn't hold up the rest of the day's work.Where to use itSuitable for indoor and outdoor repairs on concrete, render, screeds, masonry, plasterboard, timber and fibre-cement sheet. It is handy for patching floors before coverings, forming small ramps, and tidying up around doors, windows and plumbing penetrations internally.How to useClean out the damaged area so it is sound and dust free. Mix the powder with clean water (approximately 1.5L per 5kg) to a smooth, workable consistency and apply firmly with a trowel, compacting into the repair. It can be worked from a feather edge up to 20mm thick and shaped before it stiffens. Work in small batches, as the working time is around 15 minutes.Important notesOnly mix what you can place within the working time. Deeper repairs can be built up in stages. Backed by a 10 year guarantee when used as directed - see the technical datasheet for full details.Specifications Size 5kg bag Coverage Varies with patch depth; feather edge to any thickness Thickness Feather edge up to 20mm per application Substrates Concrete, render, screeds, masonry, plasterboard, timber, fibre-cement Walk-on time 45 minutes (floor coverings after 1 hour) SafetyCement-based powder - wear gloves, safety glasses and a P2 dust mask when mixing, keep the area ventilated and avoid prolonged skin contact with the wet mortar. Wash hands after use and keep away from children.
$35.86
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened Safety Contains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. For eye contact, rinse with water for 15 minutes and seek medical advice. If swallowed, do not induce vomiting and seek medical advice. Keep out of reach of children. Always refer to the Safety Data Sheet before use.
$33.75
Krud Kutter Original Cleaner and Degreaser 946ml (Ready to Use Trigger Spray) Krud Kutter Original is a water-based cleaner, degreaser and stain remover that handles tough soils across a wide range of surfaces from a single bottle. Packed in a 946ml trigger pack, it sprays on straight from the bottle for everyday messes and can be used at full strength on the most stubborn grease and grime. It is biodegradable, low in odour and free from bleach, ammonia and harsh solvents, which makes it a practical choice for kitchens, garages, workshops and outdoor areas alike. Formula overview The formula combines a water base with a gentle surfactant system, an alkaline builder and a chelating agent that together lift fats, oils, road film and ground-in dirt. Because it relies on water-based chemistry rather than petroleum solvents, it rinses away cleanly, leaves no oily residue and is safe on most washable indoor, automotive and marine surfaces. It is colour fast and fabric safe on most materials, though a spot test is always sensible before a full clean. Where to use it Indoors Kitchen benches, splashbacks, range hoods, oven exteriors and BBQ grills Tiles and grout, sinks, tubs and shower screens with soap scum build up Painted walls, skirting and doors (test first and dilute for light marks) Lifting food and drink stains, marker, crayon, scuff marks and grease spots Outdoors Concrete paths, driveways and garage floors with oil and grease staining Outdoor furniture, fences and rendered or masonry surfaces Tools, machinery and engine parts (use on a cold, dry engine) Removing tree sap, bird droppings, brake dust and general weather grime How to use Always test on a small, hidden area first to check surface compatibility. For everyday cleaning, spray directly onto the surface and let it sit briefly. Wipe away with a clean, damp cloth or sponge. For heavy grease, oil or dried paint, apply at full strength, leave for a few minutes, then agitate with a brush or pad before wiping with a wet rag. For lighter cleaning over larger areas, the concentrate can be diluted with water. Rinse food contact surfaces with clean water after cleaning. Important notes Do not use on varnished surfaces or on leather. The formula is alkaline, so avoid prolonged contact with bare aluminium and other sensitive metals, and rinse and dry after use. Always test painted, delicate or porous surfaces in an inconspicuous spot before a full clean. Do not mix with other cleaning chemicals. Keep out of reach of children and pets. Specifications Brand Krud Kutter Product Original Cleaner, Degreaser and Stain Remover Format Ready to use trigger spray (concentrate, dilutable) Size 946 ml Base Water-based, biodegradable Use Interior and exterior Suitable surfaces Sealed hard surfaces, tiles and grout, glass, most plastics, metal, concrete and masonry, automotive and marine surfaces Not suitable for Varnished surfaces and leather Safety Keep out of reach of children. Avoid contact with eyes. If product enters the eyes, rinse with plenty of water and seek medical advice if irritation continues. Wear gloves if you have sensitive skin, and wash hands after use. Use in a well ventilated area and avoid breathing in the spray mist. Store upright in the closed bottle, away from extreme heat. Refer to the manufacturer Safety Data Sheet for full handling, first aid and disposal guidance. Glues Australia ships Australia wide. If you are not sure whether Krud Kutter is right for your surface, contact our team and we will help you pick the right cleaner for the job.
$20.05
Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Blast away built up grime, dirt, and weather stains across large outdoor areas with this powerful concentrate. Designed for Aussie backyards, it cuts through tough mess on concrete, pavers, brick, tiles, and timber or composite decks so outdoor spaces look fresh and inviting again. Why you will love it Heavy duty clean that tackles road film, mildew stains, leaf tannins, and greasy marks. Concentrated value so one bottle makes multiple buckets of ready to use solution. Fast results with minimal scrubbing on most surfaces. Versatile for driveways, decks, paths, patios, and outdoor walls. Hose or pressure washer friendly for quick coverage on big jobs. Ideal surfaces Concrete driveways and garage floors Pavers, brick, stone, and outdoor tiles Timber decks and composite decking Rendered walls and fencing Outdoor furniture settings made of hard materials Dilution guide Job type Mix ratio Where to use Heavy build up 1 part cleaner to 4 parts water Oil spots, mildew stains, leaf marks on concrete and pavers General cleaning 1 part cleaner to 10 parts water Routine driveway and deck washes Maintenance 1 part cleaner to 20 parts water Frequent quick cleans and large areas Coverage: A 5L concentrate can make many litres of solution and clean a large area depending on dilution, surface porosity, and soil level. How to use Sweep the area to remove loose debris. Mix to the required ratio in a bucket or pressure washer reservoir. Wet the surface, then apply generously with a garden sprayer, watering can, mop, or pressure washer. Allow 3 to 5 minutes contact time. Do not let the solution dry on the surface. Agitate stubborn spots with a stiff outdoor broom or deck brush. Rinse thoroughly with a hose or pressure washer, pushing residue to drainage. Tips for best results Test on a small hidden patch first to confirm surface compatibility and desired result. Work in the shade on cool surfaces for even cleaning. On timber decks, scrub along the grain and rinse well. Repeat a light application rather than over concentrate for delicate areas. Important information Not recommended for raw or polished natural stone that is sensitive to cleaners. Always patch test first. Avoid use on freshly sealed surfaces. Check sealer instructions before cleaning. Keep runoff away from ponds and delicate plants. Pre wet adjacent garden beds and rinse after cleaning. Safety Wear gloves and eye protection during mixing and application. Ensure good ventilation if using in semi enclosed areas. Store upright in a cool dry place out of reach of children and pets. Specifications Size 5L concentrate Form Liquid cleaner Application Bucket, sprayer, or pressure washer Suitable areas Driveways, decks, patios, paths, outdoor walls What is in the box 1 x Glitz Outdoor Cleaner Concentrate for Driveways and Decks 5L Frequently asked Will it remove oil stains Heavy oil may require a second application and some scrubbing. For long standing or deep oil, use a degreaser first, then follow with this cleaner for an even finish. Can I use it with a pressure washer Yes. Mix in the detergent tank as per the dilution guide, apply from the bottom up, allow dwell time, then rinse from the top down. Is it safe for sealed decks Patch test first and follow the sealer brand care instructions. Rinse well after cleaning. Good to pair with Outdoor deck brush or stiff broom for agitation Garden sprayer or pressure washer for fast coverage Protective gloves and safety glasses for safe handling
$27.15 $20.89
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$55.26 $38.48
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Get a clean, hardware free look with T-Rex Clear Double Sided Tape. This high performance clear mounting tape creates a strong, permanent bond for photos, hooks, cable clips, house numbers, trims, and light decor. It is ideal when you want the hold without the hardware and a finish that stays virtually invisible on glass, tiles, metal, and painted walls. Why you will love it Crystal clear finish that helps hide the fix for a neat result Strong permanent bond for everyday mounting and craft projects Moisture and UV resistant construction for long lasting performance Instant stick with pressure activation, no curing time required No tools needed, peel and stick application Great for Mounting signage, house numbers, and name plates Securing cable clips and small hooks Fixing splashback trim and edging Crafts, scrapbooking, and photo boards Temporary holding during light assembly Works on Glass and mirrors Glazed tiles and ceramics Metal, aluminium, and stainless steel Finished timber and laminate Painted walls that are sound, clean, and fully cured Most rigid plastics except low surface energy plastics Note: Not recommended for wallpaper, delicate or dusty surfaces, or low surface energy plastics such as PE, PP, and PTFE. Always test on a small area first. How to use Prepare the surface. Clean with isopropyl alcohol and let dry. Remove dust, grease, and loose paint. Apply tape. Cut to length. Apply tape to the lightest item first. Press firmly along the whole strip. Peel liner. Remove the protective liner without touching the adhesive. Mount. Position carefully. Press firmly for 30 to 60 seconds to activate the bond. Maximum strength develops with time under steady pressure. Removal tips Warm gently and peel back slowly at a low angle Use adhesive remover to clean any residue on robust surfaces Avoid pulling straight out from the wall to reduce risk of paint lift Specifications Brand T-Rex Product type Clear double sided mounting tape Width 19 mm Length 4.5 m Colour Clear Adhesive Acrylic based Indoor or outdoor Indoor and protected outdoor applications Liner Peel off release film Good to know For best results on painted walls, ensure paint is fully cured Heavier items may need additional strips to spread the load Use continuous strips near the edges of flat panels to reduce shear What is in the pack 1 x roll T-Rex Clear Double Sided Tape 19 mm x 4.5 m FAQs Can I use it in wet areasYes for sealed, smooth surfaces such as glazed tiles and glass. Avoid constant immersion. Will it damage paintIt can if paint is weak or not fully cured. Test first and remove slowly with heat to soften the adhesive. Can it hold shelvesThis tape is ideal for light mounting and trim. Use mechanical fixings for shelves and heavy items.
$22.74 $17.05
Dunlop Ready-To-Go Vinyl Flooring Spray Adhesive is a fast and tidy spray-on adhesive for installing vinyl sheet, vinyl tiles, and vinyl planks with vinyl backing over concrete, underlayment grade plywood, metal, and fibreglass. It delivers an even spray pattern, strong bond, and immediate traffic readiness once rolled. Why choose this adhesive Quick, clean spray application that saves time High initial grab for reliable placement Dry to touch in about 10 to 40 minutes Up to 3 hours open time once tacky Ready for immediate foot traffic after rolling Heat weld flooring 1 hour after installation Suitable with underfloor heating systems Water based acrylic blend with very low odour Suitable substrates Concrete, underlayment grade plywood, metal, and fibreglass. Use on vinyl-backed sheet, tiles, and planks. Not suitable for Cushion-backed flooring products. Surface preparation Ensure the substrate is flat, dry, and free from dust, oil, paint, old adhesive, wax, curing compounds, sealers, and hardeners. Lightly damp-mop concrete to remove fine dust before application. Correct surface imperfections before installation to avoid telegraphing. How to use Ventilate and mask the area to protect adjacent surfaces from overspray. Shake the can well and remove the blue safety tab. Hold the can upright 50 to 76 cm above the substrate and spray in smooth, even passes to achieve a uniform frosted look. Avoid heavy patches and overspray. Lightly re-spray missed areas if needed. Allow to dry until no adhesive transfers to the fingertips. Lay the vinyl and roll firmly within 1 hour using a suitable heavy roller to ensure full contact. The floor is ready for immediate use once rolled. Heat welding can commence after 1 hour. Key technical data Chemical type: water based acrylic blend Dry to touch: approximately 10 to 40 minutes Open time after tack: up to 3 hours Traffic allowance: immediate after rolling Underfloor heating: compatible Appearance when sprayed: milky white frost Storage and safety Store between 10°C and 50°C. Avoid freezing and direct sunlight. Pressurised dispenser. Do not pierce or burn the can, even when empty. Use in a well ventilated area and avoid contact with eyes and skin. Tip: Wipe any overspray from adjacent surfaces with a damp cloth before it dries.
$48.36
Dunlop Tile-All Plus Premixed Tile Adhesive 310ml Tile-All Plus is a single component, silane modified polymer adhesive and neutral curing sealant. It offers high initial tack, strong bonding and excellent flexibility. Use it for fast, reliable repairs in showers, kitchens and bathrooms, for replacing tiles, fitting accessories and finishing joints. It can even be used for minor repairs underwater. Why you will like it High initial grab for confident positioning Flexible bond that resists movement and vibration Neutral cure for a low odour application experience Works as both an adhesive and a sealant Paintable after drying with most common paints (test first) Where to use it Showers, kitchens and bathrooms Replacing loose tiles and fitting trims or accessories Finishing expansion and connection joints Minor underwater fixes on suitable surfaces Suitable materials Glass, tiles, ceramics, timber, plastics, metals, concrete, wall panels, waterproofing membranes, aluminium, polystyrene foam, and glazed tiles. Always ensure surfaces are sound, clean and free from dust, oil, grease and coatings. Slightly damp substrates are acceptable. How to use Remove the aluminium seal at the base of the cartridge. Pierce the inner membrane, fit the nozzle and trim to the required bead size. Apply in stripes to the substrate or the item being fixed. Press parts together firmly within 7 to 10 minutes at 20°C, before skinning begins. For spot fixing, keep glue points 25 to 30 cm apart and confirm the item weight is appropriate. Avoid application below 5°C or above 35°C. Good to know Open time varies with temperature, humidity and substrate. Higher humidity shortens open time. If reusing, remove any skinned layer from the nozzle before the next application. Spills can be wiped away while wet with a clean cloth. Not recommended for chemical resistant applications. Cleanup and storage Clean excess while wet with a cloth. Shelf life is up to 12 months in unopened packaging stored in a cool, dry place at around 23°C and 50 percent relative humidity. Safety Use in a well ventilated area. Avoid skin and eye contact. If contact occurs, flush eyes with water for at least 15 minutes and seek medical advice. Wash skin with soap and water. If inhalation discomfort occurs, move to fresh air. If swallowed, drink water in small portions and seek medical advice. Keep out of reach of children.
$27.98
Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.
$20.74
Bastion Bond Breaker Joint Sealant Professional silicone bond breaker for wet areas. Create a flexible, waterproof separation at wall to wall and wall to floor junctions so your membrane and tile system can move without cracking. Ideal for bathrooms, showers, laundries and balconies. Why choose this sealant Permanently flexible to absorb movement in corners and junctions Neutral cure silicone suitable for use with most waterproofing membranes Low odour, low VOC, indoor use friendly Excellent adhesion to common building materials including concrete, masonry, ceramic tile, porcelain and most metals Water resistant once cured and designed for wet area applications Easy to gun out and tool for a smooth finish Typical uses Forming a bond breaker fillet in shower bases, bathrooms and laundries before waterproofing Movement joints at internal corners prior to tiling General wet area sealing where a flexible joint is needed Surface preparation Ensure surfaces are clean, dry and free from dust, oil, loose material and old sealant. Mask adjacent edges for a neat finish if required. For wide gaps, insert backing rod to control sealant depth. How to apply Cut the cartridge nozzle to the desired bead size and load into a standard caulking gun. Gun a continuous bead into the corner or joint. Aim for a smooth cove fillet in the 5 to 12 mm range. Tool the bead with a spatula or rounded tool to compact and shape it. Remove masking tape while the sealant is still wet. Allow the bond breaker to skin before applying compatible waterproofing membranes over the area. Follow your membrane manufacturer’s recoat time. Cure and finishing Skin time is typically minutes depending on temperature and humidity. Full cure occurs over 24 to 48 hours for standard beads. Thicker sections require longer. After the membrane has cured, complete tiling and finish perimeter joints with a sanitary grade silicone. Clean up Wipe away excess immediately with a clean cloth. Once cured, remove mechanically by trimming and peeling. Handy tips Not paintable. If painting is required, paint adjacent surfaces before sealing. Always use backing rod for large joints to control sealant depth and reduce three sided adhesion. Pre test on sensitive or natural stone surfaces. Do not use in continuously immersed conditions or for structural glazing. Storage and packaging Cartridge size: 300 mL Store upright in a cool, dry place. Use before the best by date printed on the cartridge. Safety Use in a well ventilated area. Avoid contact with skin and eyes. Keep out of reach of children. Refer to the product label for first aid directions. In the box 1 x 300 mL cartridge of Bastion Bond Breaker Joint Sealant 1 x application nozzle
$10.85 $9.77
Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.
$21.58
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$46.22
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$47.44
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load): – At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area – At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$143.34
Davco Supamastic is a ready to use white wall tile adhesive for internal areas. It is ideal for porous tiles and porous substrates in residential spaces and delivers non slump performance with easy water cleanup. Key benefits Ready to use paste with fast and easy cleanup White formulation suits light coloured tiles and grout lines Non slump for reliable hold on walls Low VOC Classified D1TE to AS ISO 13007 Best for Internal wall tiling with porous tiles greater than 3 percent absorption Residential dry area floors with porous backed tiles over primed cement sheet or ceramic tile underlay Suitable substrates Fibre cement sheet Plasterboard Ceramic tile underlay Rendered blockwork and brickwork Davco K10 Plus waterproof membrane on walls only Tile types Ceramic and mosaics Natural stone that is not moisture sensitive Not suitable for Porcelain tiles larger than 200 x 200 mm Concrete substrates Moisture sensitive stone Coverage Approximate coverage with a 6 mm notch trowel: 4 L covers about 3 m². Application guide Ensure the substrate is sound, clean, dry and properly primed. Spread adhesive with a suitable notch trowel at about 60 degrees and comb in one direction. Press tiles firmly into the ribs and slide across the rib direction to collapse the ribs and remove voids. Back butter large format tiles if required to achieve full coverage. Clean excess adhesive from joints and tile faces with a damp sponge while wet. Set and cure times at 22°C and 50% RH Open time: about 30 minutes Adjustability: about 45 minutes Grout after: 24 hours Dry area service: 48 hours Wet area service: 7 days Practical limits Layer thickness up to 4 mm Apply and cure between +5°C and +35°C ambient and substrate temperatures Drying times extend in cool weather, over membranes and with low porosity tiles Good to know If tile or substrate porosity is uncertain, consider a suitable alternative adhesive from the same brand for low porosity tiles. Install movement joints to applicable standards and allow adequate drying before grouting.
$66.24
Davco Supamastic is a ready to use white wall tile adhesive for internal areas. It is ideal for porous tiles and porous substrates in residential spaces and delivers non slump performance with easy water cleanup. Key benefits Ready to use paste with fast and easy cleanup White formulation suits light coloured tiles and grout lines Non slump for reliable hold on walls Low VOC Classified D1TE to AS ISO 13007 Best for Internal wall tiling with porous tiles greater than 3 percent absorption Residential dry area floors with porous backed tiles over primed cement sheet or ceramic tile underlay Suitable substrates Fibre cement sheet Plasterboard Ceramic tile underlay Rendered blockwork and brickwork Davco K10 Plus waterproof membrane on walls only Tile types Ceramic and mosaics Natural stone that is not moisture sensitive Not suitable for Porcelain tiles larger than 200 x 200 mm Concrete substrates Moisture sensitive stone Coverage Approximate coverage with a 6 mm notch trowel: 4 L covers about 3 m². Application guide Ensure the substrate is sound, clean, dry and properly primed. Spread adhesive with a suitable notch trowel at about 60 degrees and comb in one direction. Press tiles firmly into the ribs and slide across the rib direction to collapse the ribs and remove voids. Back butter large format tiles if required to achieve full coverage. Clean excess adhesive from joints and tile faces with a damp sponge while wet. Set and cure times at 22°C and 50% RH Open time: about 30 minutes Adjustability: about 45 minutes Grout after: 24 hours Dry area service: 48 hours Wet area service: 7 days Practical limits Layer thickness up to 4 mm Apply and cure between +5°C and +35°C ambient and substrate temperatures Drying times extend in cool weather, over membranes and with low porosity tiles Good to know If tile or substrate porosity is uncertain, consider a suitable alternative adhesive from the same brand for low porosity tiles. Install movement joints to applicable standards and allow adequate drying before grouting.
$81.13
Poly Ultra Nails Construction Adhesive is a high strength, versatile adhesive designed for bonding a wide range of building materials both indoors and outdoors. It offers exceptional adhesion, easy application, and water resistance, making it a reliable choice for construction and renovation projects. Features High strength bonding suitable for multiple materials Repositionable for up to 20 minutes for precise alignment Waterproof once cured Ready to use straight from the cartridge Brown finish for a natural look Suitable Materials Concrete, brick, plasterboard, ceramics Plywood, particle board, aluminium Hardwood, softwood, steel, fibreglass Some plastics (pre-test recommended) Application Instructions Ensure surfaces are clean, dry, and free from dust, grease, or flaking paint. Cut the seal, fit the nozzle, and cut to the desired bead size. Insert into a caulking gun. For wall panelling and sheet flooring, apply 6mm beads along studs or joists in a zig-zag line at 40cm intervals. Bring surfaces together within 10 minutes and press firmly along glue lines. Reposition if needed within 20 minutes. Fix with nails, screws, or clamps for at least 24 hours to ensure bond strength. For contact bonding, apply to one surface, bring together, then separate for 3–5 minutes before rejoining. Clean tools and excess adhesive with mineral turpentine. Technical Information Coverage: Approximately 15 metres of 5mm bead Initial bond: Within 24 hours at 25°C Full cure: Up to 7 days Colour: Brown Important Notes Not suitable for mirrors, polystyrene foam, or continuous water immersion Avoid use on copper-based metals or metals exposed to direct sunlight heat Do not use for tightly clamped joints or heavy loads without mechanical fasteners Safety Information Use in a well-ventilated area and avoid breathing vapours Wear protective gloves and eye protection Keep away from heat, sparks, and open flames Keep out of reach of children If swallowed, do not induce vomiting — contact a doctor or Poisons Information Centre (AUST 131 126; NZ 0800 764 766) Contains 30% w/w liquid hydrocarbons
$4.85
Bastion Premixed Tile Adhesive 15 kg Overview Bastion Premixed Tile Adhesive 15 kg is a high quality tile adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials ceramic tiles porcelain tiles mosaics stone suitable for porous adhesives most interior substrates Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Ideal application between 10°C and 30°C. Protect from freezing and rapid drying. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Pot life and open time vary by product. Typically, tiles can be adjusted within minutes. Grouting commonly permitted after 24 hours under standard conditions. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Clean excess adhesive from tile faces immediately with a damp sponge. Hardened material must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$45.00
Dunlop Floor Tile Adhesive 4kg is a premium cement-based adhesive formulated for fixing a wide range of floor tiles, including ceramic, porcelain, mosaics, and natural stone. It provides strong bonding performance, easy application, and long-lasting durability for both indoor and outdoor projects. Key Features Ideal for floor installations in residential and commercial settings Suitable for concrete, cement screeds, compressed fibre-cement sheets, and existing tiles Strong adhesion with excellent workability and pot life of up to 2.5 hours Can be used indoors and outdoors for versatile tiling applications Grey colour finish for consistent, professional results Coverage Recommended trowel: 10 x 10 x 10 mm Approximate coverage: 0.4 m² per kg Typical total coverage: around 1.6 m² per 4 kg bag Mixing Instructions Use approximately 400 ml of clean water per 1 kg of powder. Add powder to water and mix to a thick, creamy consistency. Allow to stand for 5 minutes, then re-mix thoroughly before use. Do not add additional water once mixed. Application Apply with a suitable notched trowel ensuring full coverage under tiles. Spread only enough adhesive that can be tiled within the open time. Press and slide tiles at right angles to the notches for full contact. Do not exceed a bed thickness of 10 mm or less than 3 mm. Allow adhesive to set for approximately 24 hours before grouting. Limitations Not suitable for continuous water immersion such as pools or tanks Do not use over timber floors or non-absorbent substrates like metal Not recommended for substrates subject to movement or shrinkage Additional Information Clean tools with water immediately after use Shelf life: up to 12 months when stored sealed in a dry location Full traffic after 24 hours at 23°C and 50% relative humidity 10 Year Guarantee: Backed by Ardex Australia Pty Ltd against manufacturing defects when used according to the manufacturer’s directions. Based on Dunlop official technical data sheet. Always follow the latest installation guidelines and safety instructions.
$28.90
Dunlop Trade Resaflex Rapidset Tile Adhesive 15kg is a high quality, fast setting, rubber modified cement-based adhesive designed for rapid installation and early grouting. It delivers strong adhesion on walls and floors and is suitable for interior applications and exterior areas with satisfactory drainage. Key benefits Ready to grout in about 3 hours at 23°C and 50% RH Rubber modified formulation for strong bond and improved workability Classified C1FES1 Suitable bed thickness from 1.5 mm up to 10 mm Wall and floor use, interior and exterior (with correct falls and drainage) Suitable tiles Ceramic, porcelain, vitrified and mosaics Non moisture sensitive stone Suitable substrates Render, plasterboard, fibre cement sheet walls Compressed fibre cement sheet floors, concrete floors Existing tiles for interior applications Mixing and use Water addition: 5.5 L to 6.0 L per 15 kg bag Pot life: about 40 minutes at 23°C and 50% RH Trowel guidance: 6 x 6 x 6 mm on walls to achieve about 1.5 mm bed. 10 x 10 x 10 mm on floors to achieve about 2.5 mm bed Back buttering recommended for deeply keyed tiles and tiles larger than 450 mm on any edge Grouting: typically after about 3 hours at 23°C and 50% RH Coverage guide Trowel size Approximate coverage 6 mm About 0.6 m² per kg (about 9 m² per 15 kg) 10 mm About 0.4 m² per kg (about 6 m² per 15 kg) Movement joints Include movement joints in line with AS 3958 and around perimeters, penetrations and changes in direction. Fill with a suitable flexible sealant. Clean up Clean tools and residue with water while the adhesive is wet. Limitations Not suitable for continuous immersion such as swimming pools Not for moisture sensitive or translucent stone Do not tile directly over timber floors Safety Wear gloves, eye and face protection. Avoid breathing dust. In case of contact with eyes, rinse with water and seek medical advice. Keep out of reach of children. Technical details are based on manufacturer guidance at standard conditions. Actual times and coverage vary with temperature, humidity, tile and substrate.
$56.95
You have seen 192 out of 281 products
Find products tagged for use on concrete. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on concrete surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
