FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$175.00
Polyfilla Rapid 30 100g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 100g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 100g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$12.35
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$84.97
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$83.99
A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$21.60
A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$54.08
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](http://gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
$11.94
![Parfix Roof Gutter Concrete Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697115751_115bf094-7ace-4242-bb30-259319ee7c44.png?v=1754712242&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a grey, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$10.27
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$11.49
Partix Multipurpose Filler Powder This product is ideal for filling cracks, holes and gaps inside the home. It is strong and can be easily sanded to a smooth finish ready for painting. When dry, it can be nailed or screwed without splitting or breaking. SUITABLE FOR Interior repairs to plaster, brick, plasterboard, masonry and timber. For repairs where movement occurs, use Parfix Gap Filler. PREPARATION Ensure surfaces are clean, dry and free from dust and loose material. Glossy surfaces should be roughened with sandpaper to provide key. MIXING Add 2½ parts of Parfix Multi-Purpose Filler to 1 part water (by volume) and mix thoroughly into a smooth paste with a clean filling knife. Once mixed, stays workable for up to 45 minutes. Do not add water to extend working time. 4 Contamination with dried filler will shorten the working time. APPLICATION Press filler into crack with a flexible filling blade (overfilling slightly to allow for sanding back) then smooth off. Wait 3-4 hours for filler to dry before sanding with a medium grade sandpaper Use a damp sponge to wipe away dist CLEANING Clean tools with water and reseal pack after use. Store in a cool, dry place. PAINT PREPARATION Before painting, apply a suitable primer/undercoat
$14.75
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$13.90
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$59.90
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$31.11
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$52.31
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$27.90
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$13.90
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$29.00
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services. With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand. FEATURES Premium quality 100% silicone Non-corrosive Neutral cure AS 4020 approved BENEFITS Quick exposure to light running water Suitable for use in all weather UV resistant Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$11.04
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
Safer for the environment and still does the work. The EcoConcepts Graffiti Remover is a revolutionary development in the ongoing struggle to remove paint, ink, permanent marker and unwanted graffiti from a variety of surfaces. Unlike traditional graffiti removers, EcoConcepts is environmentally-friendly and much safer for the user. Suitable for removing paint, pen, sticky residues, grease, oil, crayon, lipstick and more. Made from renewable ingredients and readily biodegradable. Contains no carcinogens, phosphates, chlorine bleach or harsh solvents. EcoConcepts represents truly green cleaning. Diluted with water it can be used on plastic, laminate, metal, carpet, most painted surfaces and whiteboards. Undiluted it will penetrate and remove graffiti from porous surfaces such as brick, stone or concrete. I’m a concentrate and nearly ready for use. Use undiluted for the toughest jobs on porous and durable surfaces. Dilute for use on less stubborn stains and less durable surfaces. Always test on an inconspicuous area first. UNDILUTED For ultimate paint and stain removal, especially on unpainted surfaces such as concrete. HIGH DILUTION Generally safe on less durable and painted surfaces – 1 part product to 5 parts water, e.g. 167mL of product makes 1L of high-dilution solution. LOW DILUTION For tougher jobs on relatively durable surfaces – 1 part product to 3 parts water, e.g. 250mL of product makes 1L of low-dilution solution.
$42.54
An effective and easy-to-use neutral cleaner designed to remove general household dirt, grime, and oils from tiles and grout. Ideal for daily use, this cleaner is powerful enough to tackle grease in kitchens and bathrooms while being gentle enough for regular application. Key Benefits: Powerful cleaner for tiles and grout Effectively removes grease in kitchens and bathrooms Regular use reduces mould and mildew growth Suitable for general-purpose surface cleaning Cost-effective when diluted and applied by spray Easy to use for everyday cleaning Use On: Tiles, grout, and general household surfaces Surface Type: Walls and floors Location: Indoor and outdoor use Colour & Sizes: Size: 1L Item Code: 22504 Coverage: Wipe On: Dilute 10ml per 1L of water Spray On: Dilute 6ml per 1L of water Directions for Use: Test First: Before the first application of Dunlop Tile & Grout Cleaner, test a small amount of product in an inconspicuous area to ensure the desired result. Dilution: Mix 10mL of Dunlop Tile & Grout Cleaner per 1L of water. For best results, use hot water. Application: For general cleaning, apply the cleaner using a mop. For stubborn dirt, use an appropriate scourer or scrubbing pad that won't scratch the tile surface. Keep your tiles and grout clean and fresh with this powerful, easy-to-use cleaner, perfect for daily household maintenance.
$25.02
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$64.80
Dunlop Multipurpose Floor Leveller is a high-flow, cement-based compound ideal for smoothing and levelling uneven internal concrete surfaces before applying tiles, vinyl, carpet, or other floor coverings. Designed for ease of use, it pours and spreads to form a smooth surface ready for foot traffic and covering in minimal time. It’s perfect for domestic and light commercial applications. Surface Preparation: Ensure the surface is sound, dry, and clean. Remove all traces of dust, grease, oil, curing compounds, wax, or any loose particles. New concrete must be fully cured. Mechanically remove surface laitance or contamination. Porous surfaces may require priming to reduce absorption and improve adhesion. Priming (if required): Apply a compatible primer using a broom or roller and allow it to dry before applying the leveller. On extremely porous substrates, a second coat may be necessary. Mixing Instructions: Slowly add the contents of the 5kg bag to approximately 1L of clean water while stirring with a mixing paddle. Mix for 2–3 minutes until a lump-free, smooth consistency is achieved. Do not retemper once the mixture begins to set. Application Instructions: Pour the mixed product onto the floor and spread using a steel trowel or smoothing blade. The product will self-level and settle to a smooth finish. Apply at a thickness of 1–10mm in one application. Protect from foot traffic until it is fully cured. Coverage: Covers approximately 3.5m² at 1mm thickness per 5kg bag. Coverage varies with substrate texture and thickness. Drying Time: Walkable: 4 hours Ready for tiling: 4–6 hours Ready for other coverings: 24 hours Dry times will vary depending on temperature, humidity, and layer thickness. Clean Up: Clean tools and mixing equipment with water immediately after use. Do not allow the product to dry on tools or surfaces. Technical Data: Type: Cement-based self-levelling compound Application Thickness: 1mm to 10mm Working Time: 15–20 minutes Walkable: After 4 hours Final Cure: Up to 24 hours Colour: Grey Shelf Life: 12 months if stored in original, sealed packaging
$40.20
Dunlop Floor Repairer Rapid Patch Mortar is a high-performance, fast-setting compound ideal for repairing holes, cracks, and uneven surfaces on internal floors. Suitable for use prior to the installation of tiles, vinyl, carpet, or other floor coverings, it delivers a smooth, level finish ready for light foot traffic within 45 minutes and covering applications in as little as 2 hours. Surface Preparation: Ensure the substrate is clean, sound, and free of grease, dust, oil, paint, or other contaminants. Surfaces should be dry and firm. Smooth or sealed surfaces must be roughened or etched. For porous substrates like timber, fibre-cement, or plasterboard, priming may be required. For floors in direct contact with soil, a moisture barrier should be used before applying the patch mortar. Mixing Instructions: Add 5kg of product into approximately 1.5L of clean water in a clean container. Mix thoroughly with a mixing paddle to a lump-free, smooth consistency. Mix only what can be used within 15 minutes. Application Instructions: Apply with a steel trowel to the required thickness (up to 20mm in a single application). Shape and smooth the surface before the material begins to set. For deeper repairs, additional layers can be applied once the initial layer has set. Avoid adding extra water once mixed. Coverage: Approximately 3m² at 1mm thickness per 5kg bag. Coverage varies with surface texture and thickness applied. Drying Time: Initial set: ~45 minutes Ready for coverings (tiles, vinyl, carpet): ~2 hours Final cure: 24 hours (depending on thickness and ambient conditions) Clean Up: Clean tools and equipment immediately with water before the mortar sets. Technical Data: Type: Rapid-setting cementitious repair mortar Application Thickness: Up to 20mm Pot Life: 15 minutes Foot Traffic: 45 minutes Ready for Coverings: 2 hours Colour: Grey Shelf Life: 12 months in original unopened packaging stored in a dry area
$39.52
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details
$144.00
Davco® Tile & Grout Cleaner is specially formulated to tackle tough dirt and stains from tiles and grout. It’s also effective in removing minor efflorescence, making it a versatile cleaner for common tiled surfaces. Key Benefits: Specially formulated ingredients Effectively cleans tiles and grout Removes minor efflorescence from grout Helps remove mould and mildew from grout surfaces Usage: Davco® Tile & Grout Cleaner is suitable for a wide range of tiled surfaces, including: Ceramic Porcelain Mosaic Quarry Slate tiles It’s ideal for removing tough dirt and stains from tiles, as well as refreshing aged grout. Packaging: Size: 1 Litre Jerry Can Colour: Clear liquid Application Steps: Mixing: Dilute Davco® Tile & Grout Cleaner with water in a clean plastic bucket at a ratio of 10 parts water to 1 part cleaner (e.g., 5L of water to 500ml of cleaner). Application: Prepare the Surface: Always wet the surface with clean water using a mop or sponge before applying the product. For Normal Cleaning: Dampen a mop or sponge with the diluted solution and wipe over the surface, then immediately rinse with clean warm water. For Heavily Soiled Areas: Apply a larger quantity of the solution and allow it to soak for up to 10 minutes. Scrub the affected area with a stiff nylon brush, then rinse thoroughly with clean warm water. Keep your tiles and grout clean, refreshed, and free from tough stains and minor efflorescence with Davco® Tile & Grout Cleaner.
$33.54
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder
$30.14
Davco PrimeX Multipurpose Acrylic Primer 5L is a professional-grade, water-based primer specially formulated to improve the adhesion of tile adhesives and waterproofing membranes to porous surfaces. Ideal for interior and exterior walls and floors in domestic and commercial applications, this primer ensures strong bonding performance while reducing porosity and dusting of substrates. Surface Preparation: Surfaces must be clean, dry, and free from dust, oil, grease, wax, paint, curing compounds, and other contaminants. Remove any laitance, loose materials, or previous coatings that may interfere with adhesion. On hot or windy days, dampen porous substrates lightly to avoid flash drying—but do not leave standing water. Application Instructions: Stir the primer thoroughly before use. Apply evenly using a roller, brush, broom, or squeegee in a thin, consistent layer. Allow the primer to dry fully before proceeding—drying is complete when the white, milky appearance turns clear. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Typically dries within 30–60 minutes under standard conditions. Cooler temperatures or high humidity may extend drying time. Clean Up: Clean tools and equipment with water immediately after use. Do not allow the product to dry on tools. Technical Data: Type: Acrylic-based Colour: Milky white (dries clear) Suitable for: Cement render, concrete, fibre cement sheets VOC Content: Low Packaging: 5 Litre plastic container
$88.36
Davco Grey One Pot Premixed Tile Adhesive is a high-performance, ready-to-use acrylic-based adhesive, perfect for interior wall and floor tiling. Its premixed formula eliminates the need for onsite preparation, providing excellent adhesion and ease of application for both professionals and DIYers. Surface Preparation: Ensure all surfaces are sound, dry, and free from dust, oil, grease, or any other contaminants. Painted or glossy surfaces should be roughened and cleaned. For porous surfaces, priming may be required to ensure maximum adhesion. Application Instructions: Stir the adhesive thoroughly before use. Using a notched trowel, apply the adhesive to the substrate. Only spread as much adhesive as can be tiled within 20 minutes. Firmly press tiles into the adhesive, ensuring full coverage on the tile back. Adjust tiles within 20 minutes of placing them. Allow adhesive to set for 24 hours before grouting. Coverage: Approximately 0.75–1.25 m² per litre using a 6mm notched trowel. Coverage may vary depending on substrate and trowel size. Drying Time: Allow 24 hours before grouting. Full cure achieved within 7 days under normal conditions. Clean Up: Clean tools and excess adhesive with water immediately after use. Once dried, adhesive is more difficult to remove. Technical Data: Appearance: Grey paste Base: Acrylic Open Time: 20 minutes Adjustment Time: 20 minutes Application Temperature: 5°C to 35°C Ready for Grouting: After 24 hours
$30.24
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Bostik Nail It Fast Cure White: The Acrylic Adhesive for Rapid, Strong & Odorless Bonds Product Overview Bostik Nail It Fast Cure is a fast-curing, versatile acrylic adhesive that offers strong and durable bonds. It's easy to apply and almost odorless. Key Benefits Solvent-free formula Suitable for EPS and XPS Non-corrosive towards metal Easy to apply and clean Applications Specifically developed for bonding: Wood, chipboard, hardboard uPVC to brickwork, stone or concrete Ceramic tiles to porous substrates Limitations Not suitable for PE, PP, PC, PMMA, PTFE, soft plastics, neoprene, and bituminous substrates. Not designed for continuous exposure to water or for movement joints. Application Instructions Apply the adhesive in a ventilating manner, using vertical stripes or dots. Material should be placed by shoving and pushing firmly. Surface Preparation All substrates must be solid, clean, dry, and free from grease and dust. For porous substrates, priming may be required. Cleaning & Maintenance Tools and uncured material can be cleaned with water or Methylated Spirit. Cured material must be removed mechanically. Bostik HANDY WIPES are recommended for cleaning hands. Colour Options Available in white.
$6.96
$22.78
$38.96
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
$12.69
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
You have seen 281 out of 281 products
Find products tagged for use on concrete. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on concrete surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
