Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier. Key benefits Softens cured silicone and many common sealants to aid scraping and removal Helps break down adhesive residue, tapes and grime build-up Non-drip gel action for vertical joints, corners and trims Low mess application with excellent wetting of tight gaps Preps surfaces for fresh re-sealing and re-bonding Where to use Bathrooms: around showers, baths, basins and splashbacks Kitchens and laundries: benchtop perimeters, sinks and tiles Windows and doors: frames, trims and glazing edges Suitable substrates Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals Some plastics and laminates (always test first in an inconspicuous spot) Not recommended on Natural stone, marble or porous tiles Freshly painted, delicate or lacquered surfaces Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics Directions Cut away and remove as much old sealant as possible with a plastic scraper. Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue. Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness. Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots. Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing. Pro tips Score thick beads along the edges with a utility blade before application to help penetration. Work in manageable sections and avoid letting the remover dry on the surface. Always test on a small hidden area to check surface compatibility. Safety Use in a well ventilated area and wear gloves and eye protection. Avoid contact with skin and eyes. Keep out of reach of children. Product details Brand: Selleys Type: Sealant and adhesive remover Pack size: 375g
$38.69
Selleys Araldite Rapid Epoxy Adhesive 14 mL Fast-setting, two-part epoxy for quick, durable repairs at home, in the workshop, or on site. The self-mixing syringe makes application clean and precise, setting in about 90 seconds and reaching handling strength soon after. Dries translucent for a neat finish. Key benefits Sets in approximately 90 seconds for rapid fixes High strength bond up to 75 kg/cm² when fully cured Dries translucent for low-visibility repairs Self-mixing nozzle for easy, accurate application Versatile bonding across common materials Best for Everyday repairs and small assemblies Fixing chipped ceramics and china Metal, glass, leather, rubber, and many plastics Suitable materials China, metal, glass, leather, rubber, and most plastics. Not suitable for PTFE, polyethylene, or polypropylene. How to use Prep Abrade, clean, and dry both surfaces. Attach nozzle Remove cap, fit and lock the self-mixing nozzle, then purge a small amount until evenly mixed. Apply Spread adhesive on both surfaces and join within 1 minute. Hold Support the bond for about 10 minutes to prevent movement. Cure Maximum strength develops after about 16 hours. Allow longer in cold conditions. Clean up Wipe away uncured adhesive with acetone. Remove and dispose of the used mixing nozzle before the adhesive sets in the tip. Technical details Technology Two-part epoxy Set time About 90 seconds Handling time Approximately 10 minutes Full cure About 16 hours Colour when dry Translucent Temperature resistance Up to 60 °C Pack size 14 mL self-mixing syringe Good to know Bond may soften above 60 °C and regains strength when cooled. Pre-test on leather and rubber to confirm suitability. May discolor with prolonged UV exposure. Store in a cool, dry place. Replace cap after removing the used nozzle. Safety Follow the safety directions on the packaging. Use in a well-ventilated area and avoid skin contact. Keep out of reach of children.
$19.26
Glue Dots Flexible Hang Tabs Brand: GlueDots Make decorating effortless and worry free. Glue Dots Flexible Hang Tabs give you a fast, clean and removable way to hang balloons, banners, streamers, paper lanterns, lightweight garlands, bunting, ornaments and more. The crystal clear tabs apply in seconds, hold firmly to most smooth household and event surfaces, and remove cleanly when the party is over. Damage free: removes cleanly from most properly painted, sealed and smooth surfaces when used as directed. Instant bond: pressure sensitive adhesive grips on contact for quick setup. Crystal clear: low visual impact for a neat, professional look in photos and in person. Flexible design: engineered slot holds standard latex balloons without helium, plus tabs act as anchor points for string, ribbon or fine wire. No tools, no mess: no nails, pins, tacks or putty required. Indoor friendly: ideal for homes, venues, classrooms, offices and display windows. Why choose Flexible Hang Tabs From last minute birthday setups to polished corporate events, these tabs are your decorating shortcut. The flexible slot lets you slide in a balloon neck or thread ribbon, while the clear base keeps the focus on your décor. When it is time to pack down, the removable adhesive lets you lift and peel without gouging walls or leaving sticky residue. Versatile surfaces: painted walls, sealed plaster, varnished timber, tile, glass, metal, laminate and most smooth plastics. Looks better: clear tabs virtually disappear against most backgrounds. Saves time: decorate large areas quickly with repeatable placement. Reliable hold: grips evenly across the tab to help prevent droop. Great for Balloon walls and garlands without helium Banners, bunting and streamers across hallways or backdrops Paper lanterns, pom poms and lightweight ornaments from ceilings Classroom displays and noticeboards where pins are not allowed Retail window dressing and temporary point-of-sale displays Wedding, engagement, baby shower and seasonal décor How to use Prepare the surface: ensure it is clean, dry, smooth and free of dust, oils and cleaning sprays. Fresh paint should be fully cured. Peel and place: remove a tab from the liner, align and press firmly for several seconds to ensure full contact. Hang décor: slide a balloon neck into the slot or thread ribbon, cord or lightweight line through the tab opening. Adjust if needed: for best results, reposition immediately after placement before full bond develops. Removal and clean up To remove, gently lift a corner of the tab and peel it back slowly over itself at a low angle. If resistance is felt, pause and continue slowly. On delicate finishes, test in an inconspicuous area first. Dispose of tabs with household waste. No solvents or scraping required when used as directed. Pro tips Use multiple tabs to distribute weight across wider banners or garlands. Avoid textured, dusty, damp or porous surfaces which reduce adhesion. For ceiling applications, ensure the surface is smooth and dust free. Allow items that were stored cold to reach room temperature before use. Indoor use recommended. Prolonged exposure to moisture, heat or direct sunlight may reduce performance. Safety and care Keep out of reach of small children. Not a toy. Do not use to hang valuable, fragile or irreplaceable items. Always test on a small area of the surface if uncertain. Specifications Brand GlueDots Product name Flexible Hang Tabs Colour Clear Adhesive type Pressure sensitive, removable Finish Crystal clear, low profile Recommended use Indoor, temporary decorating and light display mounting Suitable surfaces Painted and sealed walls, sealed plaster, varnished wood, tile, glass, metal, laminate, most smooth plastics Unsuitable surfaces Textured, dusty, damp, porous, unsealed or flaking finishes Residue on removal Removes cleanly when used as directed on suitable surfaces Repositionable Yes, during initial placement Operating conditions Room temperature, dry environment Applications Balloons, streamers, banners, paper lanterns, pom poms, lightweight ornaments Tools required None Country of use Suitable for Australian homes, venues and classrooms Performance can vary with substrate, surface preparation and environmental conditions. Always follow the directions and test before full application. What you get Flexible, clear hang tabs on an easy peel liner. Pack quantities vary by selection. Choose the pack size that suits your event or display plan. Storage Store in a cool, dry place away from dust and direct sunlight. Keep in original packaging until use to protect adhesive surfaces. Plan your next event From birthdays to window displays, build cleaner backdrops and crisper lines with Glue Dots Flexible Hang Tabs. Add to cart and get decorating in minutes.
$13.00
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.98
Ready to use, hard drying acrylic putty filler Ideal for repairing cracked, broken or uneven surfaces 30 minute fast drying time Includes bonus applicator Suitable for fibrous cement, brick, plaster and wood surface repairs available in 500gm/1.5kg Not suitable for wet areas or where structural movement occurs
$7.42
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$18.48
Tarzan's Grip Mounting Tape is a double sided, heavy duty, high strength tape that instantly grabs for easy, fast and permanent mounting. It is ideal for a multitude of surfaces, including metal, wood, rubber, leather, china, brick, stone, plasterboard and most plastics. Extremely strong Instant grab Solvent free Permanent
$12.42
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength. Uses: SikaBond Fast can be used on most substrates due to its excellent adhesion. These include: - Fixing polystyrene wall panels - Replacing loose tiles on walls - Skirting boards, architraves and trims to walls - Bonding panels to wall studs - Bonding particleboard, plywood, fibre cement and strip flooring to joists Advantages : - Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards” - Natural wood colour - Reduces the number of mechanical fasteners required to install floors or walls. - Can be repositioned for up to 60 minutes after application - Reduces squeaking associated with nail ride in floors - Paintable with water-based surface coatings - Easy to use one component - Bridges gaps up to 9 mm - Strong adhesion to metal - No fumes - High bond strength and heat resistance - Flows easily at all temperatures - Easy cleanup - Fast initial grab – minimises slippage on vertical surfaces Storage and Shelf Life Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years. Instructions for Use Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous. Application Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges. Cleaning The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means. Technical Data (Typical) Colour Pale Brown Specific Gravity ~ 1.4 Skinning Time 20 minutes Repositioning Time 60 minutes Full Cure 24 hours depending on conditions When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation). Service temperature -5ºC to +90ºC Packaging 420 gram cartridge (12 cartridges per box)
$8.69
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$16.13
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$88.91
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$15.46
Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages Fast curing. Will not damage plastic shower liners. Panels can be relocated for up to 30 minutes after positioning. Excellent adhesion to most common building materials. Easy to apply and clean up. Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining. Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive. Brace the lining as required in the shower manufacturer's installation instructions. Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.
$19.07
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler. Features Suitable for interior and exterior applications Good adhesions to most surfaces Water and weather resistant Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water-based, so can be cleaned up with water Paintable with oil and water-based paints Where can this product be used? Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs What materials is this product suitable for? Mortar Masonry Concrete Wood Stone Primed metal surfaces Brick Plaster Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next. Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications). Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints. Limitations: Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps. Avoid using below 5°C or in wet conditions. Painting with oil-based paints is not recommended until 24 hours after the filler has been applied. Water-based paints may be used immediately after the filler has set. If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency. Application tools may be cleaned with water. Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen. In exterior applications, protect from rain until dry and painted over with 2 coats of paint. Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry. For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times. Keep container closed when not in use.
$22.66
![Selleys No More Gaps Filler Sealant Fast Dry [White]](http://gluesaustralia.com.au/cdn/shop/files/da7575e6045648c8aee7c9769b69a8cc.jpg?v=1757753086&width=645)
Selleys No More Gaps Fast Dry has been designed to be painted over in just 20 minutes so that you can finish the job sooner! No More Gaps Fast Dry also provides superior crack resistance with high flexibility and low shrinkage. Features Paint over in 20 minutes* Superior crack resistance Superior adhesion to a broad range of surfaces, resulting in a lasting finish A smooth flawless finish and minimal shrinkage Can be cleaned up easily and quickly with water Will not stain building materials Can be used indoors and outdoors *Allow longer drying times before painting with flat or ceiling paints or in cooler weather. Where can this product be used? Architraves Skirting boards Cornices Window and door frames Wall joints What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Painted surfaces Many other building materials How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into caulking gun such as Selleys Light Speed Caulking gun. Apply with caulking gun, forcing product into gap. For a smooth finish, smooth with a finger dipped in water. For a professional finish use a paint scraper such as a 50mm Soft Grip Scraper. Clean up excess with a damp cloth immediately and clean hands and tools with water. Allow to skin (about 20 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured. Limitations: For gaps between tongue and groove boards and weatherboards use No More Gaps® Exterior & Weatherboard. Where movement is excessive or for areas where contact with water is frequent, use the appropriate Selleys® Silicone Sealant. Handy Tips To avoid paint cracking, apply at temperatures above 10°C and do not apply paint too thick. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler, and a perfect finish. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. Allow the surfaces to skin prior to painting, which is approximately 20 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. For exterior applications protect from rain until firmly skinned. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$7.56
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$24.79
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format. Features Superior water resistance. Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability. Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement. Mould resistant-contains a fungicide to help protect against unsightly mould growth. Can be painted over with both water and oil based paints Easy water clean-up Low odour Where can this product be used? Bathroom vanities Bathroom cabinets In and around glass and tiles Cabinets Architraves Skirting boards Bench tops Windows Door frames What materials is this product suitable for? Ceramics Glass Aluminium Most Plastics Cement Sheeting Wood Plasterboard Many other building surfaces How to Use Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun. Apply with caulking gun, forcing product into gap Smooth with a wet spatula. Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes. Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours) To allow product to strengthen, protect from water for 24 hours. Limitations: Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses. Not recommended for prolonged contact with water. Handy Tips Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler. Remove the tape before the gap filler skins. If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water. Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick. Allow longer drying times before painting with flat or ceiling paints and in cooler weather. Can be applied to damp surfaces however product must be allowed to dry following application.
$12.50
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces
$10.55
Liquid Nails Fast is a water-based high strength (*) construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. After drying it is beige (light tan) in colour. UsesLiquid Nails Fast has high initial (immediate) grab which reduces the need to support joins while the adhesive cures. The initial grab works best with porous surfaces. It will bond to many building materials including MDF, particle board, timber, plaster board, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results are achieved when at least one surface is porous. Liquid Nails Fast would typically be used for the following applications: Areas where nailing is not desirableSkirting boards, architraves, cornicesWall panelling to masonryStyrene foam to metal roofing Technical FeaturesFast grab – high initial holding minimises slippage when adhering on vertical surfacesMeets or exceeds AS 2329-1999 (Mastic adhesives for fixing wall boards)Does not drip, sag or string between panelsBridges gaps and will adhere materials with uneven surfacesLow mess – excess and squeeze out is easily cleaned up with wet clothNo solvent fumes – ideal for large indoor jobsHigh flexibility – will withstand thermal movement and vibrationHigh heat resistance – will not lose bonds exposed to sunPaintable when dryEasy to extrude at all temperatures Application TipsLiquid Nails Fast should always be used in conjunction with permanent mechanical fasteners except in low stress applications such as wall panelling and fixing light weight objects. (Bonds may creep under constant heavy loads.)Bonds are not water resistant. Protect bonds from water penetration if used in exterior applications.In cold or damp weather and between non-porous materials drying time is greatly extendedThick applications take longer to dry than thin applicationsPre-test plastics to determine suitable bonding. Adheres well to UPVC. Not suitable for polyethylene and polypropylene. For wood flooring applications Liquid Nails (solvent based) is recommended. [Liquid Nails Fast is satisfactory for fixing sheet flooring (particleboard/ply) to joists in conjunction with the manufacturer’s minimum nailing specification but is not recommended for fixing sheet wood flooring to flat surfaces such as existing or concrete floors. Technical Details and PerformanceFor porous substrates good bond strength is achieved after 24 hours and will continue to strengthen over 2-3 day period. Time for strong bond depends on nature and conditions of application. In cold or damp weather and between non-porous materials, drying time is greatly extended. Indicative information only, not to be used for setting specifications. AppearanceLump free, air-free smooth beige paste Specific GravityApprox. 1.44g/mL @ 25oC ViscosityTypical 7000 – 9000 Poise SlumpTypical: 0mm Shear Adhesion Strength (7 days) (AS2329)Greater than 1500kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure)Typical 40N/25mm (wire gauze off hoop pine.(Variant to AS2329)) Initial Bond Strength AS2329-1999D (Tested after 24 hrs)Over 200kPa Heat ResistanceBonds will resist temporary exposure to temperatures up to 140oC. Constant high temperatures will reduce constant load holding power (see below). Creep resistance (under constant load)*2Fully cured *1 bonds of 625 sq. mm will hold up to 500g loads (7.8kPa) in shear at constant 80oC Fully cured *1 bonds of 625 sq.mm will hold up to 100kPa in shear at 25oC (equivalent to 6Kg load on 625 sq.mm bond area) Coverage15 metres of a 5mm diameter bead 1mm thick bonds on porous substrates cured at least 7 days at temps above 25oCThis data is provided as indicative only. Not to be used for design purposes. Thick bonds reduce constant load holding power and increase curing time. Larger bond areas increase curing time. CleaningLiquid Nails Fast may be cleaned off with hot soapy water or a damp cloth while still wet. Dry adhesive is best removed by scraping or peeling.
$8.93
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$19.41
The Selleys 3-in-1 Adhesive, Sealant & Gap Filler is your ultimate all-in-one solution for a wide range of DIY and professional applications. This versatile product combines the power of a strong adhesive, the reliability of a waterproof sealant, and the precision of a gap filler, all in one easy-to-use formula. Whether you're tackling home repairs, sealing joints, or filling cracks, Selleys 3-in-1 ensures a durable, flexible, and weather-resistant finish. Perfect for both indoor and outdoor use, it adheres to a variety of surfaces including wood, metal, glass, and ceramics. With Selleys 3-in-1, you can trust in a product that delivers exceptional results every time, simplifying your projects and saving you time and effort Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material damp or dry,inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water based paints. Limitations: Not recommended for solvent based paints. If required, paint with a water based paint first. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean Up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Size: 480g Cartridge Colour: White Technology Sil-X® Use: Interior & Exterior
$23.38
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$39.64
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$9.35
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$39.15
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$46.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$7.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$28.90
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$4.43
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$24.50
Polyfilla Rapid 30 140g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 140g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 140g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$21.59
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$38.10
A cellulose reinforced plaster-based filler for filling interior cracks and holes that won't shrink. For use on: Plasterboard, brick, masonry & wood. Can be used also for modelling & sculpting (INTERIOR) Fill depth: Dependent on mix ratio Dries in: 2-3 hours Ready to use: NO (mix with water) Available in: 500g, 1kg, 2kg & 6kg Colour: Off-white • Surface to be filled should be clean and dry with no loose or powdery material. Roughen glossy surfaces to provide a key. • Ensure tools and mixing vessels are clean, as dried residue filler will accelerate drying rate. • Add 2.5 parts Polyfilla Interior Powder Filler to 1 part tap water and mix thoroughly into a paste with a clean knife. Once mixed, filler should be used within 1 hour. For deep cracks and holes it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Using a filling knife or applicator, press the mixed filler into the crack and smooth off. Slightly overfill and allow to dry before sanding. Use medium grade sandpaper and dust off. Wipe the dusted surface with a damp sponge. • Leave for 2-3 hours before sanding and decorating. • For best results prime repaired surface with paint undercoat paint or sealer prior to repainting the whole area. • Clean up with water before filler dries
$46.15
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out. For use on: Wood, brick, aluminium, glass, plasterboard, ceramic tiles and painted surfaces (INTERIOR & EXTERIOR) Coverage: 30m/3mm bead. Dry time: Skins in 30 minutes at 25°C. Full cure in 7days. Ready to use: YES Available in: 475g Colour: White NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps. • Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant. • Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap. • Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth. • Allow sealant to skin approx 30 min before painting with water-based paints. • Allow to set for 48 hours if using oil based paint or if joint is large. • Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting. • Do not use outside if rain is imminent, not for contantly damp areas. • Painting improves exterior durability. • Use Poly silicone sealants for a watertight seal or where movement is excessive. • Water clean up Q. How do I fill gaps between my wooden window frames and inside wall? A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth. Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened? A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat. Q. Why does my gap filler keeps cracking? A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
$5.00
Sandable Paintable Ready mixed Weather resistant Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home. Sandable and paintable, it enables a smooth finish.
$14.41
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive Key Features High-strength bond suitable for a variety of applications Paintable for aesthetic versatility Effective both indoors and outdoors Specifications Colour: Beige Model Name: Parfix 300g Maxi Nails Construction Adhesive Material: Polymer Dissolved in Hydrocarbon Solvent Outdoor: Yes Indoor: Yes Why Choose Parfix Maxi Nails 300g? Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
$4.19
![Parfix Gap Filler Flexible Paintable Interior [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
Paintable Flexible Durable Parfix Gap Filler is a multi-purpose flexible filler that is suitable for interior applications such as skirting and architraves, door and window frames.
$3.65
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
$6.02
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$14.83
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.57
Let cords be a thing of the past! Command™ Cord Management products allow you to better organise and keep your home or office space free from the mess and tangled clutter. No more dangerous, tangled cords behind your computers, appliances and entertainment centres! Command™ Cord Organisers are perfect for work and home offices, as well as entertainment areas, where they keep cords organised and safely out of the way. Holds up to 900g Damage-Free Hanging Easy to hang - no tools required! Holds strongly and removes cleanly Works on a variety of indoor surfaces, such as painted Gyprock, finished wood, tile, metal and glass Ideal for hanging and organising extension cords Prevents trip hazards
$8.99
![3M Claw Drywall Picture Hanger 65lbs 30Kg [Pack x 2]](http://gluesaustralia.com.au/cdn/shop/files/638060921234_e9940663-65b0-41b5-a196-e209139e4251.jpg?v=1754712826&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25, 45 & 65 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$17.60
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 5]](http://gluesaustralia.com.au/cdn/shop/files/638060661550_1fe37b78-c060-4f27-8387-63c1e448c0e6.jpg?v=1754712834&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$24.90
Glitz Sugar Soap for Floors Heavy Duty Cleaner Power through ground-in dirt, grease, and everyday grime with Glitz Sugar Soap for Floors. This heavy duty formula lifts stubborn residues and leaves floors fresh, streak free, and ready for living. Ideal for high traffic areas in homes, workshops, and commercial spaces. Why you will love it Heavy duty clean that cuts through grease, scuff marks, and sticky spills Low foam for a streak free finish on most sealed floors Fast acting formula reduces scrubbing time Residue free so finishes and sealers look their best Fresh, low odour for comfortable indoor use Best for these surfaces Use on most sealed and washable floors, including: Ceramic and porcelain tiles Vinyl and hybrid floors Laminate and sealed timber Sealed concrete and epoxy coated floors Do not use on unsealed timber, unsealed cork, natural stone that is unsealed, or waxed finishes. Always test in a small inconspicuous area first. How to use Sweep or vacuum to remove dust and grit. Dilute in warm water: General cleaning: 1 capful per 5 L bucket Heavy duty cleaning: 2 to 3 capfuls per 5 L bucket Apply with a mop or sponge. Work in sections. For stubborn spots, apply a little solution directly, wait 2 to 3 minutes, then gently agitate. Rinse mop frequently in clean water. Allow floor to dry before walking. Pro tips Change the bucket water when it turns cloudy to avoid streaks. Use heavy duty dilution before repainting or resealing floors to remove grease and prep the surface. For gloss finishes, wring the mop well to prevent pooling. Product details Brand Glitz Product type Sugar soap floor cleaner Format Liquid concentrate Appearance Clear to light solution, low foam Suitable surfaces Most sealed hard floors Clean up Rinse tools and mops in clean water Storage Keep tightly closed in a cool, dry place Safety Wear gloves if you have sensitive skin. Avoid contact with eyes. If splashed, rinse with water. Keep out of reach of children and pets. FAQs Do I need to rinse after cleaning Rinsing is generally not required on sealed floors when diluted as directed. If using heavy duty strength, a light rinse with clean water can help achieve a streak free finish. Can I use it in a spray mop Yes. Pre dilute following the general cleaning ratio and avoid over wetting the floor. Good to know Compatible with most microfiber and cotton mops Great prep step before resealing or repainting floors Helps remove oily residues that make floors feel slippery
$5.27 $4.94
Get crisp, professional paint lines with Wagner Mask-It. This painter’s masking tape is designed to seal neatly along the edge, reduce paint bleed, and remove cleanly when the job is done. Ideal for walls, trim, skirting boards, window frames, and any detail work where a sharp finish matters. Key Benefits Clean paint edges that help minimise bleed on most interior surfaces. Easy application with a smooth unwind and hand tearable backing. Clean removal when used as directed on properly prepared surfaces. Works with brushes, rollers, and spray for DIY and trade jobs. Perfect For Cutting in around ceilings, cornices, and trims Protecting hardware, switches, and fittings Two tone feature walls and accent colours Masking glass, tiles, and metal fixtures during repainting Surface Compatibility Use on properly prepared, fully cured interior paint, primed timber, metal, glass, and most smooth surfaces. Always test in an inconspicuous area first. How To Use Prep the surface: Ensure it is dry, dust free, and fully cured. Apply the tape: Press down firmly along the edge with a putty knife or fingernail to seal. Paint: Roll or brush away from the tape edge for best results. Remove: Peel back slowly at a 45 degree angle while paint is still slightly tacky, unless your coating specifies otherwise. Pro Tips Burnish the tape edge lightly to improve the seal on textured areas. Apply light coats near the edge. Heavy wet coats can overwhelm any mask. For long runs, overlap tape pieces by a few millimetres and press the overlap firmly. Good To Know Suitable for indoor projects and general decorating. Store in a cool, dry place away from direct sunlight to maintain performance. Available in popular widths to suit trim work and broad masking. Frequently Asked Questions Will it pull off fresh paint?Only apply to fully cured paint. Cure times vary by product and conditions. When in doubt, allow extra time and test first. Does it work on lightly textured walls?Yes, on many light textures, but press down firmly along the edge and use lighter coats near the tape line. Can I use it with spray equipment?Yes. Apply, seal the edge, and use controlled passes. Avoid flooding the tape line.
$14.80 $12.65
Speed up your painting prep with UNi-PRO Pre Taped Masking Film. This convenient roll combines quality painter’s tape with a static-cling masking film that drapes cleanly and stays put, helping you protect trims, skirting, windows, and furniture while you cut in and roll. Perfect for quick room refreshes, touch ups, and full repaints. Why you'll love it Two in one tape and film for fast, tidy masking Static cling helps the film hug surfaces and reduce paint bleed Clean removal on most surfaces when applied to sound, cured paint 550 mm drop ideal for architraves, skirting boards, window frames, and small appliances 25 m length gives generous coverage for multiple areas Suitable for brushes and rollers with water based and most solvent based paints Best for Trims, doors, window frames, skirting boards Protecting benchtops, splashbacks, and appliances during repainting Quick masking on rentals and maintenance jobs How to use Ensure the surface is dry, dust free, and fully cured. Apply the taped edge along the line you want to protect, pressing down firmly. Unfold the film so it drapes over the area. Static cling will help it stay in place. Paint as normal. Allow paint to become touch dry. Peel tape back slowly at a 45 degree angle to remove. Size and coverage Width: 550 mm drop Length: 25 m roll Approximate coverage: up to 13.75 m² of drape (when fully unfolded) Specifications Brand UNi-PRO Product type Pre taped masking film Film material High density polyethylene with static cling Tape type Painter’s masking tape Paint compatibility Water based and most solvent based paints Surface compatibility Painted timber, plasterboard, metal, glass, tiles, laminates Dimensions 550 mm x 25 m Pack contents 1 roll
$14.43 $11.68
Get pro level finishes without the fuss. Gyprock CSR Less Mess Joint Compound is a pre mixed, easy sanding compound that helps you achieve smooth, paint ready walls with less splatter and minimal clean up. The handy 2.25kg tub is perfect for repairs, patching, jointing, and touch ups around the home or on site. Why you will love it Pre mixed convenience that is ready to use straight from the tub Less mess formula that helps reduce splatter and clean up time Easy to apply, easy to feather, and easy to sand smooth Low shrinkage for fewer repeat passes Paintable finish that accepts most interior paints Great for joints, screw head covering, corner repairs, and small patches Best suited for Interior plasterboard joints and repairs Skim coating small areas to blend texture Covering fasteners and minor cracks DIY touch ups and trade maintenance work How to use Surface prep: Ensure the area is clean, dry, dust free, and sound. Remove loose material and lightly scuff glossy paint. Application: Stir gently. Apply with a broad knife or trowel in thin, even coats. Feather edges well. Drying: Allow each coat to dry fully before recoating. Dry time varies with film thickness, temperature, and humidity. Sanding: Sand lightly with fine paper for a smooth finish. Remove dust before painting. Paint: Seal with a suitable primer then finish with your chosen interior paint. Tips for a flawless finish Work in thin passes rather than one heavy fill Keep your knife clean and slightly flexible for smooth feathering Use a dry sanding block or pole sander and avoid over sanding For deeper holes, build up in multiple coats Frequently asked questions Is it sandable and paintable? Yes. Once fully dry, sand lightly and prime before painting. Can I use it on previously painted walls? Yes, provided the paint is sound, clean, and lightly keyed. Is it suitable for wet areas? Use in dry interior spaces. For wet areas, follow local building guidelines and use appropriate systems. Specifications Brand Gyprock CSR Product Less Mess Joint Compound Pack size 2.25kg tub Colour Off white Use Interior plasterboard jointing and patching Cleanup Water while wet Finish Sandable and paintable Storage Reseal tightly. Store cool and dry. Do not allow to freeze. Good to know Coverage varies with joint size, substrate, and application method Dry times depend on thickness, temperature, and humidity Always test on a small area when working over sensitive or unknown coatings Safety Use in a well ventilated area Avoid breathing sanding dust. Wear a suitable mask and eye protection Keep out of reach of children Why buy from Glues Australia Fast dispatch Australia wide Careful packaging to protect your order Local support when you need advice
$35.43 $26.02
Strengthen joints, seams, and repairs with this tough fibreglass mesh tape. It helps prevent hairline cracks, improves bond strength, and delivers a smooth base for top coats on plasterboard and cement sheet surfaces. Why you will like it Reinforces joints to reduce cracking around seams and patches Open mesh allows compound to key through for a strong bond Clean edges for easy alignment along butt and tapered joins 50mm width suits standard plasterboard seams and corner work 20m roll is great for rooms, small renos, and ongoing touch ups Great for Plasterboard joins and butt joints Repairs around door and window openings Ceiling crack reinforcement Patching holes and dents before finishing Use with base coat and top coat compounds How to use Ensure the surface is clean, dry, and free of dust. Lay the tape centered over the joint or crack, pressing to seat it flat. Apply a generous first coat of compound through the mesh and let it dry. Feather additional coats wider than the last until flush with the surface. Sand lightly once dry, then prime and paint. Specifications Brand: Builders Edge Type: Fibreglass joint reinforcement tape Width: 50 mm Length: 20 m Material: Fibreglass mesh Colour: White Tips For best results, keep the tape flat with no bubbles before coating. Use a wider knife on each subsequent coat to blend the repair. Allow full dry time between coats to avoid shrinkage lines. Glues Australia helps Australians fix, build, and finish with confidence.
$13.21 $9.32
Achieve smooth, long lasting plasterboard joints with Gyprock CSR FibaFuse Joint Tape. This premium paperless tape bonds beautifully with both setting and drying compounds to reinforce seams, reduce the risk of cracks, and deliver a professional finish on walls and ceilings. Why choose FibaFuse Stronger joints thanks to an open fiber structure that integrates with joint compound for excellent reinforcement. Smooth finishing with feathered edges that sand and paint cleanly. No bubbling when properly embedded in compound for a flat, reliable seam. Works with most compounds including setting type and ready mixed formulas. Ideal for pros and DIY on new installs, repairs, and patchwork. Best for Joining plasterboard sheets on walls and ceilings Butt and tapered edge joints Repairs to cracked or previously patched seams High traffic areas that need extra durability How to use Prep Ensure surfaces are clean, dry, and free of dust. Lightly bevel cut edges if required. Bed coat Apply an even layer of joint compound over the seam at least the width of the tape. Embed Place the FibaFuse tape into the wet compound and press firmly with a taping knife to remove air pockets. Cover Apply a thin coat over the tape to fully conceal the mesh. Allow to dry or set as per the compound directions. Build Apply one or two wider coats, feathering the edges for a flat transition. Let each coat dry before the next. Finish Lightly sand, prime, and paint. Pro tips Keep knife pressure firm during embedding to avoid bubbles. Use a wider knife for second and third coats to reduce sanding. Prime before painting for a consistent sheen across joints and boards. Product details Brand Gyprock CSR Type Paperless joint tape for plasterboard seams Compatibility Setting and ready mixed joint compounds Applications Walls, ceilings, butt joints, tapered edges, repairs Frequently asked questions Do I need to pre soak the tapeNo. Embed the tape directly into wet compound. Can I use it with ready mixed compoundYes. It works with ready mixed and with setting type compounds. Follow the compound instructions for drying or set times. Will it show through paintNot when properly covered with compound, sanded smooth, and primed before painting. Good to know Store flat and dry to maintain tape integrity. Always wear appropriate PPE when sanding joint compound. Glues Australia helps you get a strong, professional finish without the fuss. Why buy new when you can fix
$21.78 $15.70
You have seen 96 out of 366 products
Lightweight fillers, patching compounds and mounting solutions for plasterboard. Choose non-sag, fast-grab products for vertical joints; select sandable, paint-ready finishes for tidy repairs. For no-drill mounting, consider high-grab adhesives or removable tapes within load limits. Avoid saturating paper facings. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
