Loctite® Super Glue Gel has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. The gel formula works on a variety of porous and non-porous surfaces and is ideal for vertical surfaces and small gaps. Loctite® Super Glue Gel comes in a self-piercing tube; it dries clear and sets without clamping. It is also resistant to moisture, most chemicals and freezing temperatures. Recommended For -Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC -Repairing figurines, costume jewelry, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings -Ideal for vertical surfaces Not Recommended For -Exterior applications -Use on repairs needing high flexibility or for gap filling applications -Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene -Glazed surfaces -Use in dishwasher, oven or microwave Safety Precautions: -Apply in a well-ventilated area. Wear gloves. Preparation: -Surfaces must be close fitting with no gaps, clean, dry and free of oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application: In a clockwise direction, screw the cap and nozzle assembly down all the way to the tube shoulder, puncturing the tube. Remove the cap counterclockwise from the nozzle. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 60 seconds until bond sets. Do not reposition parts. Clean tip with a tissue and replace the cap. Clean-up: After cleaning, wet any tissue used for wiping off the glue with water and dispose of. When cleaning up larger quantities of uncured adhesive, apply water and allow to cure and then scrape up. Note this may result in damage to the surfaces. Cured adhesive may be cut away with caution using a sharp blade, removed with acetone or with boiling water. Note: Acetone is highly flammable and may not be suitable for use on all materials, test surface first. Follow manufacturer’s instructions.
$9.27
Specially formulated to allow more time to align surfaces before setting with less risk of finger bonding and low odour. Non-drip gel formula. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic. Properties: No immediate finger sticking. More time to align and reposition* Non-drip formula ideal for vertical application Odourless & non-irritating to skin Water resistant Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators: convenient tube or easy grip control with longer nozzle Suitable for use on most surfaces** Solvent free * Loctite Power Easy offers an initial curing time of at least double the standard Loctite Super Glue. **Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$15.50
Specially formulated to allow more time to align surfaces before setting with less risk of finger bonding and low odour. Non-drip gel formula. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic. Properties: No immediate finger sticking. More time to align and reposition* Non-drip formula ideal for vertical application Odourless & non-irritating to skin Water resistant Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators: convenient tube or easy grip control with a longer nozzle Suitable for use on most surfaces** Solvent-free * Loctite Power Easy offers an initial curing time of at least double the standard Loctite Super Glue. **Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$14.00
Loctite's versatile and reliable Super Glue Liquid is fast and strong and has a range of applicators that will get the job done quickly in every situation. It dries transparent to form a long-lasting invisible bond in seconds. Now with a NEW formula, resisting to all conditions: *Water and dishwashing *Shock *Temperatures from -50°C up to 120°C Recommended on: China, Porcelain, Metal, Rubber, Leather, Wood, Plastic (except PE/PP), Paper. Properties: Multi-use liquid superglue, ideal on non-porous surfaces Water and dishwasher resistant Shock resistant Temperature resistant (from -50°C up to 120°C) Bonds in seconds Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators - anti-spill / easy grip / long nozzle / brush-on Suitable for use on most surfaces* Solvent-free *Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$16.00
LOCTITE® SI 598™ cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. This product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers. This product is typically used in applications with an operating range of -54 °C to 260 °C. Metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. LOCTITE® SI 598 is a metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. It cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. It resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. This product is typically used in applications with an operating range of -54 to +260°C. Excellent resistance to automotive motor oils Enhances load bearing & shock absorbing characteristics of the bond area Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers Technical Information Color Black Fixture Time 30 Fixture Time Temperature 30 °C Physical Form Paste Technology Silicone TYPICAL ENVIRONMENTAL RESISTANCE The product retains effective properties in contact with automotive fluids, such as motor oil, transmission fluids, alcohol and antifreeze solutions. NOTE: Not recommended for parts in contact with gasoline. Directions for use: 1. For best performance bond surfaces should be clean and free from grease. 2. Full performance properties will develop over 72 hours. 3. Moisture curing begins immediately after the product is exposed to the atmosphere, therefore parts to be assembled should be mated within a few minutes after the product is dispensed. 4. Excess material can be easily wiped away with non-polar solvents. NOTE: LOCTITE® SI 598™ is not recommended for use as a cylinder head gasket or head gasket sealant. 5. For full automatic applications a volumetric dispensing system is recommended.
$15.52
Red, 1-part, flowable smooth, acetoxy silicone paste sealant. LOCTITE® SI 596 is a red, 1-part, flowable smooth, acetoxy silicone paste sealant. It forms a tough, flexible, waterproof, oil-resistant silicone rubber bond. It is also used as a sealant and adhesive in industrial furnaces, ovens, boilers, exhaust stacks, high temperature ducting and heating elements in electrical appliances. Resists ageing, weathering and thermal cycling without hardening, shrinking or cracking Typically used in applications with an operating range of -50°C to +250°C Technical Information Colour Red Fixture Time 30 min. Fixture Time Temperature 30 °C Full Cure Temperature 77 °F Mix Ratio No Mix Physical Form Paste Skin Formation Time 8 min. Temperature -75 - 600 °F
$11.83
Clear, 1-part, thixotropic, room temperature-cure, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor. LOCTITE® SI 595 is a clear, 1-part, thixotropic, room temperature vulcanizing, acetoxy silicone vulcanizing compound paste sealant with an acetic acid odor. It is designed as an excellent adhesive sealant for mechanical assemblies. Typical applications include electrical insulation, protection of leads from mechanical shock, trim bonding, and sealing of ductwork, vents, flues, doors, and windows. Certified to ANSI/NSF Standard 51 for use with plastic materials and components used in food equipment not exceeding +204°C. Formulated to withstand extreme temperature cycling, UV light and ozone Designed for superior bonding and sealing properties to most surfaces (not recommended for concrete) Cures on exposure to moisture in the air to form a tough, flexible, silicone rubber seal Classified by Underwriters Laboratories Inc.® E257711 - Plastics & Components Non-slumping Superior adhesion and flexibility Seals out moisture and contaminants Fills large cracks and seams Non-flammable Non-toxic Resists aging, weathering and thermal cycling without hardening, shrinking or cracking Technical Information Chemical Basis / Base Acetoxy Silicone Colour Black, Clear, White Cure Through Volume 6 mm Fixture Time 30 min. Fixture Time Temperature 30 °C Gap Fill 6 mm Key Characteristics Thixotropic Physical Form Paste Skin Formation Time 120 min. Substrates Ceramic, Composite, Glass, Metal: Aluminum, Metal: Steel, Plastic
$9.82
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended on Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fiberglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Properties High impact resistance Won’t crack when drilled Moulds into different shapes Will fit into any shape of crack Does not shrink One-time application Sandable and paintable Blends with surroundings Cures under water Great for emergency in-water repairs Step 1: Safety Precautions Wear gloves. Step 2: Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Step 3: Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Step 4: Cleanup Cured putty may be cut away with caution using a sharp blade.
$18.00
Adhesive permanently remounts mirrors to windshields LOCTITE® Rearview Mirror Adhesive is approved and used by GM, Ford and Daimler-Chrysler. Permanently remounts mirrors to windshields. Achieves handling strength in seconds; mirror-mounting strength in 15 minutes. Mounting rearview mirrors to windshields.
$25.00
LOCTITE® 249 is a blue, dimethacrylate ester acrylic film thread locker. It is supplied in a low tack film to provide a convenient and easy to use package, especially where a liquid product may be too fluid to stay on a part or be difficult to apply. This product can be used for immediate assembly or days later and provide consistent strength on a variety of metal substrates. Dimethacrylate ester acrylic film threadlocker. It is supplied in a low tack film to provide a convenient and easy to use package. Designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand tools Supplied in a low tack film to provide a convenient and easy to use package Can be used for immediate assembly or days later Provides consistent strength on a variety of metal substrates Technical Information Color Blue Cure Type Activator Cure, Anaerobic Cure Full Cure Temperature 77 °F Key Characteristics No Mix Number of Components 1 Part Physical Form Film Storage Temperature 46 - 69 °F Technology Acrylic Temperature -65 - 300 °F Thread Size (Maximum) R3/4" Torque Break on M10 Steel 74 in./lb. Torque Prevail on M10 Steel 47 in./lb. Viscosity 8700 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$16.08
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended For Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fibreglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Not Recommended For Potable water systems. Applications above 121°C (250°F). Polyethylene and polypropylene. Structural applications. Safety Precautions Wear gloves. Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Cleanup Cured putty may be cut away with caution using a sharp blade.
$35.00
IMPREGNATED WITH E-POX E RESIN WITHSTANDS HEAT UP TO 260°C Repairs engine exhaust systems of all types of cars, trucks, boats, motorcycles, and stationary engines. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. Wear goggles as eye protection 2. Warm-up muffler, peel back the red overlay on both sides of bandage and then wrap the clear center around the damaged area- overlapping 10-15mm 3. Run the motor or drive for approximately 30 minutes. The heat from the exhaust chemically welds the epoxy in the bandage into one solid protective coating NOTE: For small repairs use Loctite Muffler Putty (MP2). When repairing large holes use a piece of sheet metal ie beer can, wired between the hole and the bandage as reinforcement. When assembling new pipes and mufflers use Loctite Exhaust Joint Sealer (JS1), It guarantees carbon-monoxide leakproof joints For large mufflers more than one bandage may be required
$7.23
$6.94
LOCTITE® MR 5923 is a dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. It seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. Dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. For close tolerance flanges Slow drying Flexible setting LOCTITE® MR 5923™ seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. Typical applications include solid gasket dressing, close-fitting machined surfaces, threaded connections, aviation engines, and marine engines. This product is typically used in applications with an operating range of -54 °C to +204 °C. Technology Solvent-based Chemical Type Modified resin, fillers, and alcohol Appearance Brown liquidLMS Viscosity Flow similar to SAE 10 Motor Oil Cure Air dry Application Gasketing & sealing Specific Benefit ● For close tolerance flanges ● Slow drying ● Flexible setting Chemical/Solvent Resistance LOCTITE® MR 5923™ retains effective properties in contact with water, ethylene glycol, gasoline, motor oil, transmission fluid, and seawater Directions for use: 1. Remove all previous material from mating surfaces. 2. For best results, clean and prep the area with an oil-free solvent. 3. Remove cap. Coat with a brush-top applicator. 4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of the gasket and then position it on the assembly. Coat the second side of the gasket and re-assemble. Slower drying formula increases work time. 5. Assembly is operational after 4 hours, full cure is effective after 24 hours. 6. The product can be removed from metal surfaces with isopropyl alcohol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow it to soften overnight.
$6.67
Neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. LOCTITE® MR 5412 is a yellow, neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. Typical applications include bonding weather stripping, insulation, rubber and trim to wood and metal. Suitable for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding Technical Information % Solids 10 Agency Approvals / Specifications CFIA Listed Colour Yellow Fixture Time 15 min. Key Characteristics Waterproof Physical Form Liquid Specific Gravity 0.88 g/l Specific Gravity Temperature 25 °C Substrates Metal, Wood Directions for use: 1. Clean surfaces thoroughly. Use abrasives to remove any powdery mold release from new weatherstripping. 2. Apply a thin, even film to both surfaces. 3. Allow to dry tacky (3 to 4 minutes). 4. Bond the two surfaces together and apply enough pressure to produce uniform contact. 5. NOTE: The early strength of LOCTITE® MR 5412 is enough to hold most parts together. However, maximum strength is obtained after the adhesive is completely dry. Aging of the bond and exposure to moderate heat increases strength.
$16.45
Lubricant - emergency repair. Shock freezing (-40°C). Releases rusted, corroded and seized components. Wicks directly into the rust by capillary action. LOCTITE® LB 8040 is a special mineral oil designed to free rusted, corroded and seized parts. The shock-freezing effect will cool parts instantly down to -43 °C and cause microscopic cracks in the layer of rust. This allows the lubricating ingredients to wick directly into the rust by capillary action. The product leaves a thin film on the released parts that lubricates and prevents rust. Universal application Bactericide-free Highly resistant to micro-organisms, bacteria and fungi Excellent cooling and lubrication performance Low foaming
$25.00
White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004. Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004 LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C. PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.
$44.40
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_7b1ca3d2-d36e-4090-b9b6-2eae8421c80d.jpg?v=1754715955&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_048877d1-353e-447d-a42c-df19d2e12c4a.jpg?v=1754715955&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$19.86
Loctite Go2 Gel contains a revolutionary FLEXTEC® formulation that bonds multi-materials when projects or repairs require higher viscosity, tremendous bond strength, and resistance to extreme conditions. It is a versatile, gap-filling adhesive that bonds, seals and repairs almost all materials. It is ideal for bonds subject to harsh or extreme conditions or for situations where constant flexing is a problem. It can be used indoors and outdoors, has excellent adhesion and high initial grab that cures quickly. Loctite Go2 Gel dries clear and creates a flexible and durable bond which is dishwasher safe and has excellent resistance to vibration, impact, moisture, UV and extreme temperatures, offering long reliability anywhere it is used. Recommended For NOTE: 1See limitations below in the 'not recommended for' section. Compatible with many porous and non-porous materials such as metals1 (aluminum, stainless steel, steel, copper, brass, bronze, zinc, etc.), glass, concrete, ceramic, tiles, natural stones, wood, cork, paper, cardboard, textiles, leather, varnished surfaces1, chipboard, MDF, fiberglass reinforced polyester, rigid PVC, polycarbonate, sanded ABS, and polystyrene foam/Styrofoam™. DIY repairs and modelling work in and around the house. Not Recommended For Before application, carry out tests to ensure the compatibility with non-ferrous metals such as aluminium, copper, bronze and brass as well as with different coatings such as paints, varnishes and powder coatings. Variations in the composition may affect adhesion. Aquariums or potable water systems Archival applications Applications requiring service temperatures below -58°F (-50°C) and above 248°F (120°C) Polyethylene (PE), polypropylene (PP) and polytetrafluoroethylene (PTFE) plastics, metal-to-metal (one surface should be porous) or rubber Applications requiring solvent resistance Applications with prolonged water immersion Safety Precautions Well-ventilated area, gloves. Preparation Use between 41°F (5°C) and 104°F (40°C). Protect work area. Surfaces must be clean and free of grease, dust and other contaminants. For improved adhesion, abrade very smooth surfaces (such as metal) prior to cleaning. Remove cap. Application Apply a thin layer of adhesive to one surface. Immediately position and press parts firmly together within 5 minutes. For difficult bonds, clamp parts or use tape to hold pieces together. Do not move or use parts for at least 2 hours. Full bond strength is achieved in 24 hours. Cure times will increase with lower temperatures and humidity and if bonding two non-porous surfaces. For Gap-Filling: Apply in a thick layer to fill gaps up to 5mm max. Fix or clamp the items together for 1-3 hours and do not touch or move them. In 24 hours, 70% of full adhesion and bond strength is achieved. Cure time is 24 hours for every 2mm of adhesive. To Get High Initial Grip: Apply on both surfaces in thin and even layers. Leave for 3-5 minutes. Use as a contact cement. After, GO2 gel has become tacky, bring the items together immediately and press firmly. Fixation is not necessary in many cases. Note that final strengths decrease when used as a contact glue. Two Non-Porous Surfaces: Bonding two non-porous surfaces can result in a slower cure time and is generally not recommended. If bonding two non-porous surfaces, surfaces can be wetted using a damp cloth, taking care to avoid wetness, pooling water or drop formation, to optimize cure time. Cleanup Clean tools and adhesive residue immediately with mineral spirits. Cured adhesive may be carefully cut away using a sharp-edged tool.
$11.70
Removes glue from badly bonded objects, stained surfaces and unwanted glue spillages. How to use it on: Stained surfaces / stained clothes / badly bonded objects 1.Twist cap clockwise until it locks, then twist cap anti-clockwise to open. 2.Lightly cover stained or badly bonded area with the glue remover. 3.Place a folded tissue on top of treated area. For fabric stains, place folded tissues on both sides. Leave for several hours. 4.Remove and discard the tissue and wipe the area clean with a fresh tissue. Rinse or wash with water and dry. Repeat the process for heavy stains. How to use it on: Bonded fingers and skin 1.Apply Loctite Glue Remover to the bonded area. Allow several minutes for the glue to soften and break down. 2.Gently peel the bonded area apart. Do not attempt to force skin apart by pulling or ripping. 3.After separating, rinse the area with soapy water. Recommended on: badly bonded items, stained surfaces, ink & marker pen stains, sticky labels, bonded fingers. Properties: Corrects badly bonded items and separates accidentally bonded fingers Cleans stained surfaces, glue spillages, marker pen stains and sticky labels Easy to use Gel formula is suitable for applications on vertical surfaces
$7.24
WITHSTANDS HEAT UP TO 550°C Holes in mufflers, tailpipes, and engine pipes can be fixed immediately without dismantling Non-asbestos Hi-Temp Exhaust Repair Bandage is wet and ready to use when removed from the air sealed package. When hardened by exhaust heat, it turns into a hard, long lasting repair. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. 2. Remove bandage from the sealed foil packet and wrap the wet bandage around the damaged area with the specially impregnated material against the muffler or tailpipe, overlapping 10-15mm. 3. Support the wrapped bandage temporarily with the enclosed wire until it is heat cured. 4. Idle the motor in the open air for 20-30 minutes. The exhaust heat will harden it to a hard, protective coating.
$10.00
Loctite® Epoxy Weld Bonding Compound is a two-part system consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to quickly produce a tough, rigid, high strength bond. Loctite® Epoxy Weld can be used as a convenient alternative to welding. It can be used as an adhesive for repairing, filling and rebuilding all metal and common surfaces. It cures to a metallic gray finish and can be easily sanded, drilled, machined or painted when fully cured. Loctite® Epoxy Weld does not shrink and is resistant to most shop fluids such as water, diesel fuel, gasoline, antifreeze, hydraulic fluid, motor oil and transmission fluids. Won t crack when drilled or machined Can be used outdoors One-time application Quick completion of project Can withstand temperatures up to 350°F (177°C) intermittently Good for applications requiring shear strength up to 3000 psi High impact resistance Water resistant Does not shrink Sets in 4 to 6 minutes High heat resistance Exceptional bond strength Recommended on Repairing machinery, appliances, tools, lawnmowers, automotive components, pipes, and embedding bolts and screws into metal Bonding various types of metal such as iron, steel, aluminum, brass, bronze, copper and pewter Properties High impact resistance Won’t crack when drilled or machined Water resistant Can be used outdoors Does not shrink One-time application Sets in 4 to 6 minutes Quick completion of project High heat resistance Can withstand temperatures up to 350°F (177°C) intermittently Exceptional bond strength Good for applications requiring shear strength up to 3000 psi HOW TO USE: Step 1: Safety Precautions Avoid skin contact. Keep away from eyes. Avoid prolonged breathing of vapors. Apply in a well ventilated area. Open windows and doors to achieve good cross-ventilation. Wear safety glasses to protect eyes, and rubber or plastic gloves to protect skin. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Pierce tube nozzles using the reverse side of the caps. Squeeze out equal amounts of resin and hardener on a clean, disposable surface. Prepare only as much as can be used within 3 minutes of mixing. Recap tubes immediately after use. Match the black cap with the resin and the white cap with the hardener. Mix resin and hardener together for approximately 1 minute or until it is uniform in color. Step 3: Application Apply to surfaces to be filled or bonded. Join and press parts together. When bonding butt joints, adhesive should be applied as a reinforcing fillet or splint over the joint for additional support. Remove any excess glue immediately with acetone, mineral spirits or rubbing alcohol. Support until bond sets in 10 to 15 minutes at room temperature. Parts can be handled within 15 minutes and machined within 16 to 24 hours. Cure time is lengthened in cooler temperatures and shortened in warmer weather. Step 4: Cleanup Clean excess glue immediately with acetone before adhesive sets. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$15.17
Loctite Marine Epoxy can be applied and cured underwater and eliminates the need to drain out water before repairs. This unique epoxy is a resilient, two-part adhesive system consisting of an epoxy resin and a hardener. When mixed in equal volumes with the convenient dual-syringe applicator, the resin and hardener react to produce a tough, rigid, high strength bond that sets 2 hours and fully cures in 24 hours. Ideal for repairing PVC, copper, brass and galvanized pipes, Loctite Marine Epoxy bonds to metal, concrete, glass, fiberglass, ceramic, wood and certain rigid plastics and cures to a white finish that can be easily sanded or machined. This resilient epoxy does not shrink and is resistant to water, most common solvents, and high impact.
$30.76
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
Part N° 546018 (MA3) LOCTITE AUTOMOTIVE REARVIEW MIRROR ADHESIVE • Special Loctite bonding system for attaching metal rear-view mirror buttons to windscreens. Ideal for larger mounting brackets • Absorbs difference in thermal expansion - also recommended for metal locks and hinges on side windows and glass to metal applications on furniture. Contents: 1 piece of nylon mesh 40mm x 40mm - Diagram 1 Part B. 1 tube of Loctite adhesive - Diagram 1 Part A. Contents are sufficient for one rear-view mirror application. Note: the adhesive must be used with the special nylon mesh Directions for use: - Where convenient, remove the metal bracket from the mirror bracket. Do not damage the metal bracket Place the car in shade for at least one hour before commencing the repair. The ideal temperature for this 2 repair is between 15°C and 25°C Diagram 3: Mark an outline of the bracket on the outside of the windscreen with a marking pen Ensure the position of the bracket will result in the mirror hanging in the correct way. - Remove all old adhesive from the bracket with fine sandpaper, and from the screen with a sharp blade or razor blade. Wipe clean the inside of the screen with an ammonia-based detergent or LOCTITE SF 3 7850 Orange hand cleaner, then wipe again with a clean cloth dampened in Methylated Spirit. Allow drying. Cut the nylon mesh to the exact shape of the metal bracket that will fit onto the windscreen. Hands must be clean and oil-free while doing this. - Cut the tip from the adhesive tube (Dia. 1, Part A), apply the adhesive from the tube and spread over the entire area of the metal bracket - Place the cut to size nylon mesh onto the adhesive on the metal bracket. Important. The adhesive will begin curing within 30 seconds of contact with the nylon mesh. Diagram 7: Note Ensure the bracket is in the correct position (top and bottom front and back) With the nylon mesh and adhesive assembled, press the bracket and mesh against the inside of the windscreen aligned with the marked location and hold firm for a minimum of 30 seconds Wipe off any excess adhesive, Allow adhesive to cure for at least 15 minutes before mounting the mirror to the bracket. Warning: Adhesive may attack some painted surfaces.
$19.95
LOCTITE 660 is a high strength retaining compound with good gap filling properties, ideal for repairing worn-out seats, keys, splines, bearings or tapers without remachining. LOCTITE® 660 is designed for the bonding of cylindrical fitting parts, particularly where bond gaps occurs without the need for remachining. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. LOCTITE 660 exhibits excellent gap cure characteristics and is also suitable for retaining shims. Ideal for repairing worn parts without remachining Enables re-use of worn bearing seats, keys, splines or tapers Suitable for retaining shims P1 NSF Reg. No.: 123704 Technical Information Agency Approvals / Specifications NSF P1 Color Silver Diametrical Clearance (Maximum) Unit mm Fixture Time 15 min. Fixture Time Temperature 15 °C Gap Fill 0.5 mm Key Characteristics Thixotropic Substrates Metal: Steel
$10.59
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
High strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. LOCTITE® 609 is a green, high strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. The product cures in the absence of air between close-fitting metal surfaces. Typical applications include rotor to shafts in fractional and subfractional horsepower motors. Locks bushings and sleeves in housings on shafts. Augments press fits. Low viscosity Prevents loosening and leakage from shock and vibration Augments press fits Tested to the lot requirements of Military Specification Mil-R-46082B (this is a regional approval) Technical Information Agency Approvals / Specifications ASTM D5363, CFIA Listed, MIL-R-46082B for existing designs Application Method Pressure Applications For Close Fitting Parts, Retaining Colour Green Cure Type Anaerobic Cure Diametrical Clearance (Maximum) Unit in. Fixture Time 10 min. Fixture Time Temperature 10 °C Full Cure Temperature 22 °C Full Cure Time 24 hr. Gap Fill 0.006 in. Key Characteristics Fluorescent, Strength: High Strength, Viscosity: Low Viscosity Number of Components 1 Part Physical Form Liquid Shear Strength Unit, Steel psi Shear Strength, Steel 2300 Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal Technology Acrylic Temperature -65 - 300 °F Viscosity 125 mPa.s (cP) Brookfield Viscosity (#7sp/20/rpm) 125 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$12.12
When you have a minute - tackle even big repairs with the new Loctite 60 seconds All-Purpose Glue. It is fast, strong and repositionable. Perfect results in only 60 seconds. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic*. Properties: -Fast: it bonds materials within ca. 60 seconds -Extra strong: it builds up a strength of 100+ kg/cm² within a short time -Repositionable: it gives time to reposition the parts that you want to glue -Ideal for all home repairs, even mid-size and large surfaces -Non-drip gel formula, suitable for vertical applications -It dries transparent -Suitable for use on most surfaces* -Solvent-free -Perfectly bonds non-porous to non-porous materials *Except polyethylene (PE), polypropylene (PP), PTFE, glass, Styropor® and synthetic fibres Step by Step: 1.Ensure surfaces to be bonded are clean, completely dry and close-fitting. 2.Twist the cap/nozzle clockwise onto the tube and remove the cap. 3.Carefully apply the glue on one surface. Press the surfaces together, reposition it as you wish, then press with strong and even pressure for few seconds and leave it undisturbed for 60 seconds. 4.Clean the nozzle, replace the cap and store upright in a cool dry place.
$20.45
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing. LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part. Ideal for fine threads as used in hydraulic, pneumatic & general fittings Suitable for metal threads only Instant low-pressure seal Resistant to fuel, oil, coolants and hydraulic fluids Locks connection against vibration loosening PRODUCT DESCRIPTION LOCTITE® 542 provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Brown liquidLMS Components One component - requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Medium Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry. 3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also. 4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations. 5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours. For Disassembly 1. Remove with standard hand tools. 2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot. For Cleanup 1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
$12.26
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges. LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings. Semi-flexible, medium-strength anaerobic flange gasket Easy to automate Reduces process costs – eliminates manual assembly of conventional gaskets NSF P1 Reg. No. 123758 For active and inactive rigid metal flanges Cures through minor surface contamination Adapts to flange surface irregularities and gaps up to 0.25 mm Gel-type consistency Seals instantly against low pressure Reduces inventory costs – no need for large inventory of cut gaskets Resists high pressure when fully cured No compression set or misaligned gaskets Technical Information Applications Rigid Assembly Gasketing Colour Red Cure Schedule Temperature (Step 1) 200 Cure Schedule Temperature Unit (Step 1) °C Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.3 mm Shelf Life Temperature -40 °C Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal: Aluminum Temperature -65 - 300 °F Tensile Shear Strength 7.5 N/mm² Viscosity 500000 - 1000000 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$9.95
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$7.50
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$24.59
Black, toughened ethyl-based instant adhesive. Well suited to plastics, rubbers, metals as well as porous/acidic surfaces. LOCTITE® 438 is a black, toughened ethyl-based instant adhesive. It has a fixture time of 10 - 20 secs., high impact resistance and is flexible. It is suitable for bonding plastics, rubber, metals, porous and absorbent substrates and acidic surfaces. Good resistance in humid environments. Cures very quickly when confined between two surfaces Ideal for bonding small to medium-size parts Excellent adhesion to most substrates Suitable for rubbers and plastics Well suited to metals, porous and/or acidic surfaces Fixture time of 10 - 20 secs. Solvent-free Toughened, black
$35.00
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$5.87
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$18.32
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless. Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability. DIRECTIONS FOR USE: 1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding. 2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger. 3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform. 5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged. Structural Bonding - Fast Cure. Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance. Fixture time: 4-6 min Temperature Resistance: Up to 180°F (82°C)
$15.11
LOCTITE 290 is a medium/high strength, wicking grade threadlocking adhesive that is ideal for locking preassembled fasteners. LOCTITE® 290 is a liquid medium/high-strength threadlocker designed for the locking and sealing of threaded fasteners. Because of its low viscosity and capillary action, the product wicks between engaged threads and eliminates the need for disassembly prior to application. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The product can also fill porosities in welds, castings and powdered metal parts. Ideal for locking preassembled fasteners, e.g. instrumentation fasteners, electrical connectors and set screws Works on metal only Proven to be tolerant of minor contamination due to industrial oils, e.g. motor oils, corrosion prevention oils and cutting fluids Requires heat for disassembly
$12.48
Loctite 222 Threadlocker prevents corrosion, loosening from shock or vibration, and seals to prevent leakage. It also allows for simple, hand tool disassembly without shearing the screw. Easy to remove, it is typically used with small screws up to 1/4 inch. Recommended on Low strength Stops vibration loosening of screws and seals against leakage Prevents thread corrosion Dismantle with normal hand tools How to Use: Step 1: Safety Precautions Keep out of reach of children. Step 2: Preparation Protect work area. Parts to be sealed must be clean and dry. Shake the product thoroughly before use. Note: To prevent the product from clogging in the nozzle, avoid touching the bottle tip to the metal surface. Step 3: Application For Thru Holes: Apply several drops of the product onto the bolt at the nut engagement area. For Blind Holes: Apply several drops of the product down the internal threads to the bottom of the hole. For Sealing Applications: Apply a 360°bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360°bead of product on the female threads also. Assemble parts and tighten as required. Sets in approximately 10 minutes and fully cures in 24 hours. Step 4: Cleanup Clean adhesive residue immediately with a damp cloth. Cured product can be removed with a combination of soaking in methylene chloride and mechanical abrasion such as a wire brush. For disassembly, shear with standard hand tools and remove with methylene chloride. In rare instances where hand tools do not work because of excessive engagement length, apply localized heat to nut or bolt to approximately 250°C. Disassemble while hot.
$19.23
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$13.11
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
A heat resistant, solvent-based, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. Features; Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Grabs immediately on contact Easy to spread Appearance: Yellowish to beige coloured opaque liquid with strong solvent odour. Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing shoes Fixing laminate to tables, benchtops etc Leather shoe and leather repairs, leather work eg handbags Repairing tents and outdoor equipment Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Attaching rubbers to your fridge door Repairing your wetsuit Some plastics such as vinyl sheeting and polystyrene are attacked by Kwik Grip Solvent. Test in an inconspicuous area prior to application. Seek the advice of vinyl flooring manufacturers prior to use with their products as discolouration and bubbling can occur with some types. If in doubt, Kwik Grip Advanced is safe to use for all these applications and will provide excellent bonding. Contains highly flammable solvents and care should be taken to ensure all fire precautions are observed. As an alternative, Kwik Grip Advanced is non-flammable. Not suitable for bonding rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for these applications). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product: When bonding laminated plastics, ensure that surfaces to be bonded are clean, dry and free from grease or paint. Surfaces to be bonded should be relatively smooth and/or close fitting. Both surfaces should be completely covered with adhesive and kept apart till “touch dry” – no more than 40 minutes. Position the items carefully, still keeping surfaces apart. Remember once joined they cannot be repositioned. When edges are perfectly aligned, press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Kwik Grip Solvent to one surface then bring the surfaces together and clamp until dry. Handy tips: -Care should be taken to test plastics prior to use as solvents present will attack some polystyrene and sheet vinyls. -Up to 5sq.m/litre (bonded area 2.5sq.m/litre) depending on the porosity of surfaces. -For vertical surfaces, we recommend using SELLEYS Kwik Grip Gel Vertical. -For applications in confined or low ventilation areas eg car interior, we recommend using SELLEYS Kwik Grip Waterbased, as it is non-toxic and free of fumes. -Use a brush, knife or serrated scraper for application. -When using the contact method REMEMBER bonding is immediate once the two surfaces are joined. -Keep container sealed when not in use. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Kwik Grip Horizontal has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips: -Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. We recommend you use Kwik Grip Waterbased in these circumstances. -Highly flammable. Do NOT use in the same area as flame, fire or spark producing apparatus or machinery. -This product should not be accessible to juveniles, because of its solvent content. Intentional misuse by deliberately inhaling vapours from this product can be harmful or fatal. -Contact with skin and eyes should be avoided and avoid breathing vapour. -If in eyes flush with plenty of water for 15 minutes and seek medical advice. -If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do NOT induce vomiting. Give a glass of water and seek medical advice. -For further information refer to the Safety Data Sheet (MSDS). Storage and re-use Store in a cool area away from ignition sources and out of direct sunlight.
$7.00
WaterWeld will plug or seal leaks and patch holes and cracks in almost anything. Ideal for repairing plumbing, fuel tanks, tub and shower, drains, pool and spa, boats and potable water tanks; setup occurs even under water. After curing, it can be drilled, tapped, filed, sanded and painted. WaterWeld has a set time of 15-25 minutes and sets hard in one hour. WaterWeld cures to an off-white color, is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF. Great For: -Plumbing, Tub, Shower & Drains -Fuel Tanks -Marine & Boats -Potable Water Tanks Strenght: H900 PSI Set Time: 25 Minutes Cure Time: 1 Hour Cure Colours: Off White Use On: -Automotive -Ceramic -Epoxy Putty Sticks -Fibreglass -Metal -Plastic/Composite/PVC -Under Water/Wet -And More
$14.00
TankWeld™ is a fuel and metal tank repair kit designed for permanent or temporary repairs of metal and fuel storage containers from leaks caused by cracks of 4" or less and holes up to 1/4" diameter. This kit is not recommended for plastic repairs of for use with polyethylene or polypropylene plastic parts. GREAT FOR Metal Gas Tanks Metal Tanks & Oil Pans USE ON Metal And More
$25.00
SteelStik is a hand-mixable, steel-reinforced, non-rusting epoxy putty that quickly repairs or rebuilds anything made of metal. After mixing, it forms an industrial-strength polymer compound that can be moulded into shapes or used to build up patch and repair steel components. SteelStik sets in 3-5 minutes and after 60 minutes, can be drilled, tapped, machined, ground, filed and painted. SteelStik cures to a dark grey colour is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF. GREAT FOR Automotive & Machine Parts Exhaust Systems Plumbing Stripped Threads Rust Damage Household Repairs STRENGTH 900 PSI SET TIME 5 Minutes CURE TIME 1 Hour CURE COLOR Dark Grey USE ON Automotive Brick Ceramic Concrete Epoxy Putty Sticks Metal Under Water/Wet And More
$12.95
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More Strenght: 3960 PSI Set Time: 4-6 Hours Cure Time: 15-24 Hours Cure Colour: Dark Grey Use on: Automotive Brick Concrete Epoxy & Adhesives J-B Weld Metal Pro Sizes And More
$32.00
PlasticWeld is a specially formulated two-part adhesive and epoxy filler system that provides for strong, lasting repairs. PlasticWeld will bond a variety of surfaces, such as metal, composites, fiberglass and others. PlasticWeld sets in 5 minutes at room temperature and is fully cured in 1 hour. Using a 1:1 mixing ratio, PlasticWeld combines to a tensile strength of 3200 PSI and cures to an off-white color. GREAT FOR Most Hard Plastics ABS Fibreglass PVC Glass Vinyl STRENGTH 3200 PSI SET TIME 5 Minutes CURE TIME 1 Hour CURE COLOR Off White USE ON Automotive Ceramic Epoxy & Adhesives Fibreglass Plastic/Composite/PVC And More
$14.95
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Fibreglass Plastic/Composite/PVC Wood And More PREPARE Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. MIX After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly. APPLY Apply with appropriate tool in an even coat, weld bead or extruded shape as needed. DRY Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
$18.00
You have seen 528 out of 667 products
Find products tagged for use on metal. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on metal surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
