In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints.
For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards
Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting
Properties
Ready to use
Sand & paint after 4 hours
Super smooth white finish
Easy to sand
Maximum depth: 2 mm
Particle size: Max 0.10 mm
How to apply
Substrate and crack must be clean, dry and free from loose material.
New wood should be primed first.
Rub down gloss surfaces for improved adhesion.
Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer.
Apply with a filling knife and spread over the surface, pressing in well.
Remove any excess filler and leave to dry.
For an even smoother finish rub down with fine sand paper.
Use appropriate protection when sanding.
Do not apply when the surface temperature is below + 5°C.
Replace lid after use.
Wash tools with warm water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Make fast, tidy bonds on timber, plastics, ceramics and more with the Ozito Power X Change 18V Cordless Glue Gun. It heats up in about 120 seconds and uses standard 11 mm glue sticks, so you can tackle DIY fixes, craft projects and light repairs without cords getting in the way.
Why you will love it
Cordless convenience for indoor and outdoor jobs
Quick heat up in about 120 seconds for less waiting
Consistent flow control trigger for neat, accurate beads and dots
Interchangeable nozzles round and precision tips included for detail work
LED worklight helps you see the glue line clearly
Auto shut off after inactivity to help conserve battery
Part of Ozito PXC one battery system across tools and garden gear
What is in the box
Ozito PXC Cordless Glue Gun (skin only)
5 x 11 mm glue sticks
Round nozzle and precision nozzle
13 mm hex spanner
Ideal for
Timber trims, skirting, craft and hobby builds
Quick fixes on ceramics and some plastics
Cardboard, fabric trims and school projects
Key specifications
Battery platform
Ozito Power X Change 18V
Pre heating time
Approx. 120 seconds
Max heating temperature
170°C
Glue stick size
11 mm diameter
Weight
0.4 kg
Auto power off
Yes, after inactivity
Battery and charger sold separately.
How to use
Insert a charged PXC 18V battery and press the on or off button.
Wait until the status light indicates ready, about 2 minutes.
Feed an 11 mm glue stick and squeeze the trigger to apply glue.
Press surfaces together straight away and hold for about 30 seconds.
Stand the tool upright on the battery between uses and let it cool before storage.
Good to know
Use the precision nozzle for fine detail and the round nozzle for general bonding.
Work on clean, dry surfaces for the best adhesion.
Wear eye protection, take care around hot glue and hot nozzle areas.
Warranty
Tool is covered by a 5 year replacement warranty for DIY use. PXC lithium batteries and chargers are covered by a 36 month warranty. Keep your proof of purchase.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ozito Trigger-Flow Hot Glue Gun 10 W is a reliable compact hot melt glue gun for quick bonding and model making chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 10 W pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Ozito Trigger-Flow for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Ozito Trigger-Flow Hot Glue Gun 10 W has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Cardboard displays and craft
Light repairs and cable dressing
Attaching trims, felt, and fabric accents
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Card, paper, fabric
Wood trim and plastics that tolerate hot melt
Ceramic ornaments
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of open time is short, assemble parts promptly after application. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Hot melt sets as it cools, giving fast handling strength. Full strength is reached once the bead has cooled through.
Temperature and environmental performance
Operate in a dry area. Avoid use on heat sensitive foams that may melt. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Peel away stray strands after cooling. Protect worktops with a mat. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Unplug and allow to cool before storage. Keep glue sticks sealed from dust. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home.
Why you will like it
Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces.
Tear by hand for fast application when you do not have a knife handy.
Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners.
Good weather resistance suitable for indoor use and light outdoor tasks.
Clean removal designed to leave minimal residue when removed within a reasonable time.
Low shine finish helps reduce glare on stage, sets, and job sites.
Great for
Sealing ducting joins and flexible hose connections
Temporary patching of tarps, plastic sheeting, and packaging
Bundling cables and securing drop sheets
Edge protection on work surfaces and tool cases
Quick fixes on site, in workshops, sheds, and vehicles
Surface compatibility
Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas.
How to use
Clean and dry the surface. Remove dust, oils, and loose paint.
Unroll and tear or cut the required length.
Press down firmly and smooth from the centre out to remove air pockets.
For joints or patches, overlap edges by at least 20 mm.
To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results.
Tips
For extra hold on porous surfaces, apply additional pressure with a roller.
Avoid prolonged exposure to strong UV and high heat if a pristine finish is required.
Not a substitute for permanent structural repairs or certified electrical insulation.
Product details
Backing
PVC
Adhesive
Rubber based
Finish
Low sheen
Use
Indoor and light outdoor tasks
Removal
Minimal residue when removed within a reasonable time
FAQs
Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product.
Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape.
Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces.
Good to know
Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Keep jobs moving with a reliable, multipurpose PVC duct tape built for quick fixes and everyday maintenance. Paint Partner PVC Duct Tape bonds fast, conforms to uneven surfaces, and helps you seal, bundle, repair, and patch with confidence on site or at home.
Why you will like it
Strong instant hold grips to plastics, metal, timber, cardboard, and painted surfaces.
Tear by hand for fast application when you do not have a knife handy.
Flexible PVC backing conforms around pipes, ducts, cables, edges, and corners.
Good weather resistance suitable for indoor use and light outdoor tasks.
Clean removal designed to leave minimal residue when removed within a reasonable time.
Low shine finish helps reduce glare on stage, sets, and job sites.
Great for
Sealing ducting joins and flexible hose connections
Temporary patching of tarps, plastic sheeting, and packaging
Bundling cables and securing drop sheets
Edge protection on work surfaces and tool cases
Quick fixes on site, in workshops, sheds, and vehicles
Surface compatibility
Adheres well to smooth, clean, and dry surfaces including PVC, PE sheeting, aluminium, steel, timber, painted walls, and cardboard. Test first on delicate or freshly painted areas.
How to use
Clean and dry the surface. Remove dust, oils, and loose paint.
Unroll and tear or cut the required length.
Press down firmly and smooth from the centre out to remove air pockets.
For joints or patches, overlap edges by at least 20 mm.
To remove, peel back slowly at a low angle. Remove within a reasonable time for the cleanest results.
Tips
For extra hold on porous surfaces, apply additional pressure with a roller.
Avoid prolonged exposure to strong UV and high heat if a pristine finish is required.
Not a substitute for permanent structural repairs or certified electrical insulation.
Product details
Backing
PVC
Adhesive
Rubber based
Finish
Low sheen
Use
Indoor and light outdoor tasks
Removal
Minimal residue when removed within a reasonable time
FAQs
Is it waterproofIt resists moisture and splashes for temporary sealing. For long term underwater or high pressure sealing, choose a dedicated waterproof repair product.
Can I paint over itMost paints will not adhere well to PVC tape. Remove the tape after painting or mask with a paintable tape.
Will it damage surfacesOn most sound surfaces it removes cleanly when taken off in a reasonable time frame. Always test first on delicate, aged, or freshly painted surfaces.
Good to know
Store in a cool, dry place out of direct sunlight. Apply between 10°C and 35°C for best results.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get sharp, clean paint edges with Paint Partner Thick Masking Tape. This reliable painter’s tape is designed to stick firmly, remove cleanly within the recommended time, and resist paint bleed for professional looking results on walls, ceilings, trims, doors, and furniture.
Crisp paint lines with reduced bleed on properly prepared surfaces
Thicker construction for easy handling, straight tearing, and consistent edging
Clean removal within the recommended timeframe to help reduce residue
Suitable for most interior paint systems including acrylic and enamel
Value 6 pack for multi room or multi day projects
Ideal For
Masking skirting boards, window frames, architraves, and cornices
Two tone feature walls and colour blocking
Furniture upcycling and detailed trim work
Protecting hardware and fixtures during repainting
Specifications
Brand
Paint Partner
Product
Thick Masking Tape for Crisp Paint Lines
Width
24 mm
Length per roll
27 m
Pack size
6 rolls
Adhesive type
Pressure sensitive
Surface types
Painted drywall, timber trim, metal, glass, and sealed surfaces
Use
Interior masking and edge definition
Removal window
Remove within the recommended project timeframe for clean results
Colour
Neutral masking tape
How to Use
Prep the surface Ensure it is clean, dry, and free of dust or grease. Lightly sand and wipe where needed.
Apply the tape Align to the paint edge and press down firmly, smoothing along the full length to seal the edge.
Paint Apply paint in light coats, brushing or rolling away from the tape edge to reduce bleed.
Remove While paint is still slightly tacky or once fully dry per paint instructions, peel the tape back on itself at a 45 degree angle.
Pro Tips
Burnish the tape edge with a clean cloth or plastic card for the sharpest lines.
For textured walls, apply a very light coat of the base colour along the tape edge, let it set, then apply the top colour.
Test in a small, hidden area on delicate or freshly painted surfaces.
What’s in the Pack
6 rolls of Paint Partner Thick Masking Tape, each 24 mm x 27 m.
Storage and Safety
Store in a cool, dry place away from direct sunlight.
Use on fully cured paint only. Always test before full application.
Dispose of used tape in household waste according to local guidelines.
Frequently Asked Questions
Will it pull off existing paintWhen applied to properly cured paint and removed within the recommended timeframe, it is designed for clean removal. Always test on a small area first.
Can I use it outdoorsBest suited for interior projects. For extended outdoor exposure consider a UV resistant painter’s tape.
How do I get the sharpest edgePress the tape down firmly along the edge and remove at a 45 degree angle while paint is slightly tacky or fully cured as directed by the paint manufacturer.
Why Buy From Glues Australia
Australian based support and fast dispatch
Carefully curated paint preparation range
Competitive pricing on multi pack project essentials
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth
Directions:
Ensure all surfaces are clean, dry and free of oil, grease and wax
Shake well before use
Only apply to one surface
Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions)
Remove excess glue with a damp cloth
Great strength is achieved when dried overnight
Cleaning: Clean up with water. Wash hands after use
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters.
Highly flexible
Mould and UV resistant
Neutral cure
Non-corrosive
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms.
Immediate strong bond
Heat and water resistant
Brush application
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Paintable
Flexible
Durable
Parfix Gap Filler is a multi-purpose flexible filler that is suitable for interior applications such as skirting and architraves, door and window frames.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs
Key Features
Excellent bond to glass
Acetic cure for optimal sealing
Designed for interior and exterior use
UV resistant and shrink-proof
Specifications
Colour
Black
Model Name
Parfix Window and Glass 300g
Model Number
9300697122445
Material
Silicone polymer
Paintable
No
Stainable
No
UV Resistant
Yes
Outdoor
Yes
Indoor
Yes
Shrink Resistant
Yes
Sandable
No
Applications
Suitable for use on windows, glass partitions, and glass blocks.
Instructions
For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sanitary grade silicone
Acetic cure
Excellent adhesion
Watertight seal
Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sanitary grade silicone
Acetic cure
Excellent adhesion
Watertight seal
Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix Maxi Nails 300g: The Ultimate Multi-Surface Construction Adhesive
Key Features
High-strength bond suitable for a variety of applications
Paintable for aesthetic versatility
Effective both indoors and outdoors
Specifications
Colour:
Beige
Model Name:
Parfix 300g Maxi Nails Construction Adhesive
Material:
Polymer Dissolved in Hydrocarbon Solvent
Outdoor:
Yes
Indoor:
Yes
Why Choose Parfix Maxi Nails 300g?
Designed to handle a multitude of construction challenges, Parfix Maxi Nails 300g provides a robust bond that lasts. Whether you're working indoors or taking on external projects, this adhesive is formulated to give you the results you need.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Partix Multipurpose Filler Powder This product is ideal for filling cracks, holes and gaps inside the home. It is strong and can be easily sanded to a smooth finish ready for painting. When dry, it can be nailed or screwed without splitting or breaking.
SUITABLE FOR
Interior repairs to plaster, brick, plasterboard, masonry and timber. For repairs where movement occurs, use Parfix Gap Filler.
PREPARATION
Ensure surfaces are clean, dry and free from dust and loose material. Glossy surfaces should be roughened with sandpaper to provide key.
MIXING
Add 2½ parts of Parfix Multi-Purpose Filler to 1 part water (by volume) and mix thoroughly into a smooth paste with a clean filling knife.
Once mixed, stays workable for up to 45 minutes.
Do not add water to extend working time. 4 Contamination with dried filler will shorten the working time.
APPLICATION
Press filler into crack with a flexible filling blade (overfilling slightly to allow for sanding back) then smooth off.
Wait 3-4 hours for filler to dry before sanding with a medium grade sandpaper Use a damp sponge to wipe away dist
CLEANING
Clean tools with water and reseal pack after use. Store in a cool, dry place.
PAINT PREPARATION
Before painting, apply a suitable primer/undercoat
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sandable
Paintable
Ready mixed
Weather resistant
Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home.
Sandable and paintable, it enables a smooth finish.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sandable
Paintable
Ready mixed
Weather resistant
Parfix multipurpose filler is a versatile, ready mixed filler ideal for filling cracks, holes and gaps inside and outside the home.
Sandable and paintable, it enables a smooth finish.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear.
High strength
Clear drying
Water clean up
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear.
High strength
Clear drying
Water clean up
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear.
High strength
Clear drying
Water clean up
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can be used on both interior and exterior substrates
Highly flexible
Non-corrosive
Neutral cure
Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use.
Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can be used on both interior and exterior substrates
Highly flexible
Non-corrosive
Neutral cure
Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use.
Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Can be used on both interior and exterior substrates
Highly flexible
Non-corrosive
Neutral cure
Parfix Roof, Gutter And Concrete Silicone is a grey, highly flexible, neutral cure sealant designed for both interior and exterior use.
Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond
Instant strong bond
Sets in 10 seconds
Dries clear
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Interior and exterior use
Acetic cure
Excellent bond to glass
Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks.
Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER!
PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour.
Here are just a few specific uses (there are hundreds of other uses):
Fasten galvanized steel to a concrete floor.
Bond sheet metal to wood or masonry.
Seal and insulate electrical connections and electronic boards.
Protect electronic components from vibration and moisture.
Repair porcelain or sculptures.
Reattach multiple broken pieces in a vase.
How to prepare a surface for bonding with PC-Clear™ Epoxy
Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants.
Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Clear™ Epoxy application
Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy.
Cured epoxy can be removed with paint stripper or remover.
FAQ
Is PC-Clear™ Epoxy different from other clear epoxies?
Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing.
How does PC-Clear™ Epoxy’s strength compare to other epoxies?
PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi.
Is PC-Clear™ Epoxy brittle?
PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies.
How does outdoor exposure affect cured PC-Clear™?
Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing.
What is the best way to mix PC-Clear™?
How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life.
Why does PC-Clear™ Epoxy have a strong odor?
The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing.
Does PC-Clear™ Epoxy self-level?
PC-Clear Epoxy™ is a liquid and is self-levelling.
How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense?
PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead.
Can PC-Clear™ Epoxy be colored or tinted?
PC-Clear™ Epoxy can be tinted.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Concrete ™ Anchoring and Crack Filling Epoxy— is the epoxy chosen to repair cracks in a warehouse and factory floors. Dispense and apply using a standard size caulking gun. Cures hard enough to drive over within 3 hours at standard temperature. Nothing stronger for your anchoring applications. PC-Concrete™ is a two-component (1:1 ratio), 100% solids, high modulus, and structural epoxy paste. PC-Concrete™ is a solvent-free, no odour, high strength, moisture insensitive epoxy system. The resin and hardener are uniformly dispensed from a 9-ounce cartridge system and mixed through a mixing nozzle using a standard size caulking gun. (We recommend at least an 18:1 thrust ratio). PC-Concrete™ is also provided in a 22-ounce dual cartridge system for Contractors and Professionals. This size requires a 600ml high thrust dual cartridge dispensing gun. For filling larger cracks and cavities use the 102-ounce bulk kit. PC- Concrete™ will NOT SHRINK. Suitable for Interior and Exterior applications. Can be applied to WET & UNDERWATER surfaces.
Here are just a few specific uses (there are many other uses):
Anchor into marine docks above or below waterline
Anchor equipment to floors
Bond to pre-stressed floors
Anchor into stone and rock.
Install anchor bolts for sill plates
Anchor into foundations and block
Fill cracks in concrete allowing equipment traffic In 4 hours
Anchor into concrete railroad ties
Anchor HVAC equipment to concrete pads and roofs
Waterproof floor to wall cracks
Re-anchor railing at convention center or apartment building
Anchor seats in lecture hall or theaters
Repair broken concrete in shopping mall parking garage
Fill spalled concrete in car wash
Fix fork truck damaged concrete in warehouse
Seal crack in sanitation and chemical storage facility containment area
Repair floor in fire station garage
Anchor safe to floor prison and security pickproof epoxy
Anchor machinery
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron.
Here are just a few specific uses (there are hundreds of other uses):
Seal cracked steam or hot water radiator
Stop leaking steam fittings
Fill hole in heat exchanger
Attach thermocouple to hot surface
Seal chimney ductwork
How to prepare a surface for bonding with PC-Fahrenheit™
Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants.
How to clean-up after PC-Fahrenheit™ application
We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover.
Can PC-Fahrenheit™ repair a leaking steam radiator?
PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators.
Can PC-Fahrenheit™ be used in a fireplace or wood burning stove?
PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C.
Can PC-Fahrenheit™ be used to seal heater chimney duct?
PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range.
Can PC-Fahrenheit™ seal a rust hole in barbecue grill?
PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior.
How long should PC-Fahrenheit™ be mixed before applying?
Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply.
What is the temperature limit?
PC-Fahrenheit is not intended to exceed 260°C. -
Will PC-Fahrenheit™ burn?
PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame.
Does PC-Fahrenheit™ stick to car radiator?
Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Crete™ Epoxy is a hand-mixable, fast-setting epoxy putty that quickly repairs concrete and masonry. After mixing, it forms a concrete repair polymer that cures to a concrete-like color and texture. The mixture readily sticks to concrete and masonry surfaces and is easily shaped. It will stick to ceramics, glass, metals and some plastics. It cures within 60 minutes. Each stick contains pre-measured portions of activator and base — no measuring or mixing tools are necessary.
Here are just a few specific uses (there are hundreds of other uses):
Quickly rebuild small missing pieces of concrete
Fill holes in concrete and masonry
Rebuild missing pieces of statues and birdbaths
Seal hole for wire or conduit thru cinder block
Fill chip or spall in concrete furniture
Reattach loose or popped decorative stone
Fill crack in stone fireplace
Fill holes in brick or concrete walls; Apartment complexes, schools, government buildings etc.
Fill cracks in concrete or stucco wall before painting
Attach address numbers to brick or stone
Attach hardware to brick or stone
Fill abandoned screw holes and mounting holes in brick or cinderblock
Replace missing mortar
Seal rodent hole in cinderblock or concrete
How to prepare a surface for bonding with PC-Crete™
Old concrete must be clean and profiled or textured. Surface must be clean and sound. It may be dry or damp, but free of standing water. Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Crete™ application
Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover.
Can PC-Crete™ be used to repair a crack in a fountain?
PC-Crete™ looks like concrete and is excellent for repairing concrete fountains, statues and lawn decorations.
Will PC-Crete™ adhere to a concrete step? Can it be shaped to match a corner?
PC- Crete™ is excellent to repairs on concrete surfaces such as steps. It shapes easily and can be sanded to match the look and texture of the concrete surface.
Is PC-Crete™ suitable for filling a small crack or spall in a sidewalk or deck?
Small crack repairs in concrete are easily made with or without the use of tools using PC-Crete™. PC-Crete™ is excellent for replacing missing or loose mortar between bricks and stones.
Can PC-Crete™ be used in a fish tank or pond?
PC-Crete™ is not recommended for aquatic use. Do not use this product in aquariums or ponds.
The PC-Crete™ is not easily grabbing or sticking to the concrete surface. It pulls away lifting loose stones
The putty wants to stick to the fingers more than the concrete surface. Wet the fingers with alcohol and then press, shape and smooth the applied putty. Also, loose stones can be wire brushed away to provide a sound surface.
PC-Crete™ does not have a smooth texture. It has particles throughout
The particles in PC-Crete™ are used to simulate the appearance of concrete.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Lumber™ Epoxy Putty is pre-measured and mixed by hand. It is used as a filler where a small amount will solve the problem. Within 60 minutes it is cured and ready. The putty can be easily formed and shaped.
Here are just a few specific uses (there are hundreds of other uses):
Reset or secure loose hardware in wood (hinges, handles, latches, etc.)
Fill abandoned screw and nail holes in cabinets or paneling
Fill dings and dents in molding or doors
Fill woodpecker and carpenter bee damage to exterior siding and paneling
Rebuild display corner in retail store
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Marine™ Epoxy Putty Stick is a specially formulated epoxy putty suitable for wet or underwater applications. Incredibly it has an extended open time (20 – 30 minutes) but cures hard within 60 minutes for a fast return to service and emergency repairs. It sticks great to metals, fibreglass, tile, wood and some plastics such as ABS and rigid PVC.
Here are just a few specific uses (there are hundreds of other uses):
Seal holes and waterproof fittings
Shape and form missing corners or holes in ceramic or fibreglass fixtures
Re-attach and secure loose hardware
Fill cracks and dings in fibreglass
Seal leaks in water tanks
How to prepare a surface for bonding with PC-Marine™
Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use mineral spirits or paint thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-Marine™ application
Wear disposable gloves to minimize contact with the skin. Use denatured alcohol, acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner to cleanup before PC-Marine cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying paint remover or paint stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
Can PC-Marine™ be applied underwater?
Yes, application underwater is possible. PC-Marine™ will adhere and cure underwater. However, it is preferable to apply it in dry conditions.
Is PC-Marine™ suitable for repairing canoes?
PC-Marine™ is excellent for repairs to aluminium and fibreglass canoes but not when they are made with Hypalon.
How much time does it take for PC-Marine™ to cure?
PC-Marine™ has an extended application or open time of 20 minutes. Most repairs made with PC-Marine™ can be returned to service after 60 minutes. Some applications may require a full 24-hour cure.
Is PC-Marine™ green?
PC-Marine™ Epoxy Putty stick is white on the inside and green on the outside. The green colour disappears when mixed with the white. The result is an off-white colour when it cures.
What is the maximum thickness that PC-Marine™ Epoxy Putty can be applied?
PC-Marine™ can be applied thick or thin. There isn’t a thickness limit. It cures from the within via a chemical reaction. It does not need to dry or be exposed to air.
How much PC-Marine™ can be mixed at a single time?
PC-Marine™ is slower curing than other epoxy putties allowing larger portions to be mixed at one time. Small quantities can be mixed more thoroughly and with less effort.
Can PC-Marine™ cure in a freezer?
PC-Marine™ is not recommended for sub-freezing temperatures. We recommend an application temperature of 2°C or higher.
Does PC-Marine shrink?
PC-Marine™ does not shrink.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Plumbing™ Epoxy Putty is for pipes. Use PC-Plumbing™ to stop leaks in less than 60 minutes. Pre-measured and easy to use and 2 part epoxy putty does not require tools. Hand mix and apply. NSF® approved for plumbing repairs and for contact with potable water supply pipes.
Here are just a few specific uses (there are hundreds of other uses):
Seal leaks in copper pipes resulting from hard water
Fix freeze damaged PVC and copper pipes
Stop leaking copper elbow and tees
Fill abandoned drill holes in ductwork
Insulate electrical connections from water
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-SuperEpoxy® is a non-drip translucent paste epoxy suitable for conventional or static mixing. It has unlimited uses in bonding, assembling, filling and sealing most materials. Unlike conventional liquid epoxies, PC-SuperEpoxy® can be applied via a static mix nozzle vertically and overhead. It cures quickly at room temperature to form a resilient, non-conductive bond or seal that resists most chemicals, fresh and saltwater, gasoline and fuel oil. Works great bonding steel to wood, fibreglass, aluminium, concrete, brick, glass, block, ceramics, hard plastics and much more. PC-SuperEpoxy® is the toughest, highest strength epoxy we manufacture.
WORK TIME: 15 MINUTES AND TACK-FREE IN 60 MINUTES
CURE TIME: 4 HOURS (12 – 24 HOURS FOR FULL CURE)
Here is a product that can take on the most challenging of projects with ease.
Adhesion strength in excess of 2500 psi (up to 4000 psi).
PC-SuperEpoxy® is a gel with a consistency like Vaseline.
Here are just a few specific uses (there are hundreds of other uses):
Anchoring or securing railings to wood or fibreglass decking.
Seal cracks and holes in decking.
Attach chocks, cleats, handles and pulls.
Anchor or secure iron balusters to step and handrail.
Fill cracked wood beam.
Fix broken latch in the car glove box.
Attach axe head.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-7® is the original tough job epoxy! This paste epoxy was originally formulated more than 60 years ago for the maximum in bonding power. Professionals to the do-it-yourselfers select PC-7® because of its exceptional adhesion to metals, ceramics, masonry and many plastics. PC-7® is designed for permanent repairs. Where other adhesives fail…PC-7® won’t! Choose PC-7® if you want to: seal a crack in a wall, attach a hanger to a ceramic plaque, seal a leak in an oil pan, repair a granite monument, fix a leak in PVC pipe connection, create a multimedia sculpture, and thousands of other repairs. When mixed, part A (gray) and the hardener part B (black) react to form a bond of tremendous strength. The PC-7® formulation is slow curing, but slow can be a good thing especially for large tasks.
WORKING TIME: 60 MINUTES
CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE)
PC-7® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Thicker than peanut butter but not as thick as bubble gum.
Here are just a few specific uses (there are hundreds of other uses):
Bond metal electrical boxes to concrete wall.
Fill cracks in basement walls.
Rebuild vintage Bakelite steering wheels.
Seal holes in oil and transmission pans or fuel tank.
Bond and repair stainless steel.
Attach transition strips on concrete floor.
Attach firing strips to concrete wall.
Bond to and rebuild hard rubber bumper.
How to prepare a surface for bonding with PC-7 Epoxy Paste
Remove contaminants such as dust, dirt, oil and grime with solvents such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be scuffed using sandpaper to increase adhesion.
How to clean-up after PC-7 Epoxy Paste application
Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-7® cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
How thick can I apply PC-7®?
PC-7® can be applied in any thickness. It does not require drying or exposure to air. It will cure from the inside out.
I made a repair with PC-7® but need to build the area up more. Can I apply more epoxy?
PC-7® sticks to PC-7®
Can I use PC-7® for a vertical repair?
PC-7® can be applied vertically and overhead. Because of its high viscosity it will not drip or sag.
How long does it take PC-7® to harden?
Normally, at 70F, PC-7® will cure in 24 hours but full hardness can take up to 48 hours. Cooler conditions will extend the cure time. Working in a garage or outside in temperatures between 50F and 60F may double the length of time needed for full cure. Applying PC-7® to a cool surface such as an exterior facing wall will slow down the cure.
Can I paint over PC-7® and if so how?
PC-7® should be primed then painted. Use Zinser Bullseye® 1,2,3 Stain Sealing Primer or Kilz® Premium Stain Sealing Primer or INSL-X® Stix Bonding Primer. Priming/sealing is important to separate and protect the finish coat from the epoxy/amine surface.
Can I use PC-7® on a finished surface?
Smooth, glossy or shiny surfaces should be roughened or scuffed with sandpaper to provide maximum adhesion. Use 80 or 120 grit sandpaper. A roughened surface has much more surface area than a smooth surface.
PC-7® is very thick. Can I smooth it out or thin it out?
Use a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol or Lacquer thinner to smooth applied PC-7®. Be-cause PC-7® is very thick and gooey, it is necessary to apply alcohol or acetone to the tool or gloved fingertips in order to lubricate the surface and shape or feather the applied epoxy.
Can I use more of one part of PC-7® in order to speed the curing?
Adding additional hardener does not make PC-7® cure faster. It is best to mix PC-7® one part of A to one part of B. However, PC-7® is probably the only epoxy that does not require precisely a 1:1 mix ratio. Plus or minus 25% A or B does not affect the performance. Adding additional PC-7® (+50%) part B hardener (black) can improve the adhesion to difficult surfaces such as PVC pipe and fittings. Measure equal volumes of part A epoxy (gray) and part B hardener (black) then measure an additional half portion of hardener (black). This will make the mix ratio (1 : 1.5, A : B).
Can I tint PC-7® to match a surrounding color?
PC-7® can be tinted with iron oxide or carbon pigments. Powdered pigments are used to color stucco or concrete and can be found at art supply stores. Universal tints that are used to color paint are compatible with PC-7®. Too much tint may affect the performance of PC-7®.
I want to do a repair outdoors and the epoxy seems really stiff?
PC-7® becomes more viscous in cool temperatures. Set the containers in a warm place prior to mixing. Acetone has been used to reduce the viscosity of PC-7®. The addition of acetone will contribute to shrinking and slow down the cure rate. PC-7® performs best without the addition of solvents.
What will PC-7® bond to?
It is easier to say what PC-7® will NOT bond to: Wax paper, Teflon, Plexiglass, vinyl and some softer plastics. Test an area if in doubt and always rough up shiny, smooth surfaces with sandpaper.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper.
Here are just a few specific uses (there are hundreds of other uses):
Replace broken knob on a drill press
Insulate wire connections, secure wire nuts
Rebuild and repair zinc or aluminium gear housing
Fill abandoned drill holes in aluminium or steel
Seal stainless steel electrical panel
Stop leaking drum
How to prepare a surface for bonding with PC-Metal™
Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants.
How to clean-up after PC-Metal™ application
We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover.
Can PC-Metal™ plug a hole in a 55 gallon drum?
PC-Metal™ is an excellent product for quickly plugging a hole made in a drum.
PC-Metal™ has a strong odor. Does the smell go away?
PC-Metal’s™ odour stops after it cures.
PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal?
PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals.
How fast does it cure? How much should be mixed?
PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness.
What kind of metal is in PC-Metal™? Does PC-Metal™ rust?
It is an alloy of iron and aluminium. It will not rust.
Can PC-Metal™ be machined? Can it be tapped or cut?
Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed.
Can PC-Metal™ be used to seal a cracked engine block?
PC-Metal™ has many automotive uses even repairs to engines.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks.
WORKING TIME: 30 MINUTES
CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE)
PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter.
Here are just a few specific uses (there are hundreds of other uses):
Reattach missing swimming pool tiles.
Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat.
Repair cracked or damage swimming pool or hot tub skimmer.
Waterproof and Seal cracked fibreglass.
Seal screw holes to hatch lids or seating.
Attach fish locators to transom.
Repair stock tanks.
Repair broken refrigerator door shelf fixtures.
Repair broken pottery.
Repair shower basin or antique bath tub.
Seal leaking air conditioner drip pan.
Seal underground conduit.
How to prepare a surface for bonding with PC-11® Epoxy Paste
Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-11® Epoxy Paste application
Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
Can PC-11® be used in Aquariums?
There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed.
What plastics does PC-11® stick to?
PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite.
What plastics does PC-11® not stick to?
PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate.
What rubbers does PC-11® stick to?
PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers.
What temperatures can PC-11® be applied?
PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time.
Can gel coat be applied to PC-11®?
Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat.
Can PC-11® be painted?
Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat.
Will PC-11® yellow in direct sunlight?
Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important.
Can PC-11® be thinned with solvent?
PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible.
PC-11® is a simple one to one mix, but how accurately does the measurement need to be?
The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PC-11® thrives in wet environments. It is resistant to water whether it is fresh or salt. Thick consistency like PC-7® and long open time (30 min). Work horizontal or vertical, indoor or outdoor. Wet, dry or under water. Whether you are working on an area where you just can’t remove water and moisture or you want the white colour for your repair, PC-11® is your choice. Choose PC-11® for ceramic repairs, pools and spas, fibreglass boats, tubs and sinks, stock tanks and thousands of other repairs. It has excellent adhesive properties bonding metals, fibreglass, wood, tile and some plastics such as ABS and rigid PVC. Ample open time allows tooling or positioning in order to tackle larger and challenging jobs. When mixed, the epoxy, part A (white) and the hardener part B (lt. blue) react to form a bond of tremendous strength and flexibility. The PC-11® formulation is slow curing, but slow can be a good thing especially for large tasks.
WORKING TIME: 30 MINUTES
CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE)
PC-11® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Not quite as thick as peanut butter.
Here are just a few specific uses (there are hundreds of other uses):
Reattach missing swimming pool tiles.
Patch a hole in a fibreglass canoe or the fibreglass keel of a fishing boat.
Repair cracked or damage swimming pool or hot tub skimmer.
Waterproof and Seal cracked fibreglass.
Seal screw holes to hatch lids or seating.
Attach fish locators to transom.
Repair stock tanks.
Repair broken refrigerator door shelf fixtures.
Repair broken pottery.
Repair shower basin or antique bath tub.
Seal leaking air conditioner drip pan.
Seal underground conduit.
How to prepare a surface for bonding with PC-11® Epoxy Paste
Remove contaminants such as dust, dirt, oil, barnacles and grime with a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. For a wet or underwater surface; clean contaminants as best as you can. Solvents will not help you in this situation.
Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush.
Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion.
How to clean-up after PC-11® Epoxy Paste application
Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-11® cures.
Clean hands and skin with soap and water.
Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed.
Can PC-11® be used in Aquariums?
There is the potential for PC-11® part A and part B to harm sea life but properly measured and mixed PC-11® has been used safely in fresh and saltwater aquariums. It is important that part A and B are thoroughly and completely mixed.
What plastics does PC-11® stick to?
PC-11® has good adhesion to Rigid PVC and CPVC, polyester and fiberglass, polyurethane, ABS and Bakelite.
What plastics does PC-11® not stick to?
PC-11® does not stick to polyethylene, polypropylene, HDPE, polystyrene, nylon, acrylic, Teflon, and polycarbonate.
What rubbers does PC-11® stick to?
PC-11® sticks to SBR, Buna, and polyurethane rubbers and does not stick to EPDM, vinyl and neoprene rubbers.
What temperatures can PC-11® be applied?
PC-11® cures very slowly at temperatures below 50°F (10°C). At or below freezing temperatures the PC-11® will stop curing. In hot conditions, above 95°F (35°C), PC-11® will cure rapidly reducing the working or application time.
Can gel coat be applied to PC-11®?
Gel coat will not cure properly in direct contact with PC-11®. It is important that repairs made with PC-11® be sealed with a suitable primer/sealer before applying a gel coat.
Can PC-11® be painted?
Yes. It is good practice to apply a premium stain sealing primer to repairs made with PC-11® prior to the finish coat.
Will PC-11® yellow in direct sunlight?
Yes, PC-11® yellows in direct sunlight. PC-11® resists ultraviolet light but will still gradually change colour. Prime and paint if the colour is important.
Can PC-11® be thinned with solvent?
PC-11® does not contain solvents. Acetone and denatured alcohol (ethanol) are compatible but will extend the cure time and decrease the hardness. Other solvents such as mineral spirits, paint thinner and turpentine are not compatible.
PC-11® is a simple one to one mix, but how accurately does the measurement need to be?
The volume of part A to part B should be close to equal. A slight excess of part A is preferable to an excess of part B. Excess of part B will not accelerate the curing and it may make it softer.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Eazy Tape Plasterboard Joint Tape, your ultimate solution for achieving flawless walls and durable repairs. Designed for both the DIY enthusiast and the professional, this self-adhesive fibreglass mesh tape is engineered to simplify your plasterboard wall panel joining or patching tasks. Crafted from high-strength fibreglass mesh, it ensures a robust bond that complements both plaster filler and jointing compounds seamlessly.
Why choose Eazy Tape? Here are the benefits:
Easy to Use: With its self-adhesive backing, the application is straightforward and mess-free, adhering securely to surfaces without the need for additional glues.
DIY-Friendly, Professional Results: Whether you're tackling a home project or a professional job, Eazy Tape guarantees a smooth, professional finish.
Strong Bonding & Holding Power: The superior fibreglass mesh material provides exceptional strength, reducing the risk of cracks and ensuring longevity.
Quick Results: Speed up your repair or construction projects with a tape that sets quickly, allowing you to move on to the next step without delay.
Perfect for a wide range of applications, from repairing cracks to joining new wall panels, Eazy Tape Plasterboard Joint Tape is the dependable choice for achieving seamless results with ease.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A flexible multipurpose gap filler, to fill gaps around cornice, wall joints, skirting board, window and door frames where where movement causes ordinary fillers to crack or fall out.
For use on: Wood, brick, aluminium, glass, plasterboard, ceramic
tiles and painted surfaces (INTERIOR & EXTERIOR)
Coverage: 30m/3mm bead.
Dry time: Skins in 30 minutes at 25°C. Full cure in 7days.
Ready to use: YES
Available in: 475g
Colour: White
NOTE: Not for fine joints between tongue and groove boards or weatherboard overlaps.
• Ensure surfaces are clean, dry and free from oil, dust, grease, flaking paint and old sealant.
• Using caulking gun, push sealant ahead of nozzle forcing it onto the surface and into the joint. Ensure the sealant is touching both sides of the gap.
• Smooth with wet finger or knife and remove excess sealant immediately with a damp cloth.
• Allow sealant to skin approx 30 min before painting with water-based paints.
• Allow to set for 48 hours if using oil based paint or if joint is large.
• Some water-based undercoats and flat paints may crack on drying. Test a small section of sealant. Paint cracking may be reduced by using a vinyl/ acrylic semi glossed paint or oil based undercoats first, or by allowing the sealant to cure thoroughly before painting.
• Do not use outside if rain is imminent, not for contantly damp areas.
• Painting improves exterior durability.
• Use Poly silicone sealants for a watertight seal or where movement is excessive.
• Water clean up
Q. How do I fill gaps between my wooden window frames and inside wall?
A. You're dealing with two different materials here, plaster and wood. To allow for differential movement between them, use Polyfilla Gap Filler, wiping off any excess with a damp cloth.
Q. I painted over the areas where I used Polyfilla Gap Filler and now cracks have appeared. Why has this happened?
A. If the gap filler was not cured sufficiently before it was painted over, cracks can occur as the gap filler shrinks. To prevent this, allow 48 hours drying time when you are filling large gaps or painting with oil-based paints. Also, some water based undercoats and paints shrink during drying and as Polyfilla Gap Filler is flexible, it won't stop cracks appearing in the shrinking paint on its surface. Test the paint on a small section of gap filler and if this is a problem you can reduce cracking by allowing the filler to cure thoroughly or by first coating it with a vinyl/acrylic semi-gloss or oil-based undercoat.
Q. Why does my gap filler keeps cracking?
A. It is important to remember that the width of a gap affects how much the product can move. Fine cracks less than 2mm allow the gap filler to move only very tiny amounts before it may crack again. It is best to ensure that you have at least 3mm worth of product so you can maximise the movement capability of your joint.
![Parfix Gap Filler Flexible Paintable Interior [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9300697115751_115bf094-7ace-4242-bb30-259319ee7c44.png?v=1754712242&width=645)
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](//gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](//gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](//gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
![Poly Gap Filler Sealant Multipurpose [White]](//gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)
![Parfix Gap Filler Flexible Paintable Interior [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115812_e966678a-f2ee-4e79-abc6-2f960851c302.png?v=1754712264&width=645)
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115768_c056520c-16e5-4bd6-9d65-de084d15ff93.jpg?v=1754712245&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
![Parfix Roof Gutter Concrete Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697115751_115bf094-7ace-4242-bb30-259319ee7c44.png?v=1754712242&width=645)
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](http://gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
![Poly Gap Filler Sealant Multipurpose [White]](http://gluesaustralia.com.au/cdn/shop/files/9311531000683_aaee7eb0-0b5d-4d11-8699-1eea1db48c2c.png?v=1754712208&width=645)