In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKASIL® -670 FIRE | JOINT SEALANT
Fire-rated joint sealant
Up to 4 hours fire resistance according to EN 1366-4
Very good resistance to weathering
Easy to smooth and very good workability
DESCRIPTION
Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant.
USES
Sikasil®-670 Fire is designed for fire rated movement
and connection joints on porous and non-porous substrates.
CHARACTERISTICS / ADVANTAGES
▪ Up to 4 hours fire resistance according to EN 1366-4
▪ Very good resistance to weathering
▪ Movement capability of ± 35% (ASTM C 719)
▪ Easy to smooth and very good workability
▪ Good adhesion to many different substrates
▪ Neutral curing
ENVIRONMENTAL INFORMATION
▪ LEED® EQc 4.1
▪ SCAQMD, Rule 1168
▪ BAAQMD, Reg. 8, Rule 51
APPROVALS / STANDARDS
▪ EN 15651-1 F EXT-INT CC 25 LM
▪ EN 15651-4 PW INT
▪ ISO 11600 F 25 LM & G 25 LM
▪ ASTM C 920, class 35
▪ EN 1366-4 assessment report
▪ ETAG 026 assessment report
▪ EN 13501-2 classification report
▪ EN 140-3
▪ EN 13501-1 class B-s2-d0
PRODUCT INFORMATION
Chemical Base Neutral cure silicone
Colour: Grey
Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C.
Density 1.35 kg/l approx. (ISO 1183-1)
TECHNICAL INFORMATION
Shore A Hardness 16 approx. (after 28 days) (ISO 868)
Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339)
0.50 N/mm2 approx. at 100% elongation (−20 °C)
Elongation at Break 650% approx. (ISO 37)
Elastic Recovery 70% approx. (ISO 7389)
Tear Propagation Resistance 4.0 N/mm approx. (ISO 34)
Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719)
Service Temperature −40 °C to +150 °C
Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below).
Backing Material Use polyethylene foam backing rods.
Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390)
Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature
Substrate Temperature +5 °C to +40 °C
Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2)
Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1)
Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2)
APPLICATION INSTRUCTIONS
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without
primers and/or activators
APPLICATION METHOD / TOOLS
Sikasil®-670 Fire is supplied ready to use.
After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents.
CLEANING OF TOOLS
Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically.
FURTHER DOCUMENTS
▪ Safety Data Sheet (SDS)
▪ EN 13501-2 classification report
▪ ETAG 026 assessment report
▪ Brochure Sika Fire Protection Solutions
LIMITATIONS
▪ Sikasil®-670 Fire cannot be overpainted.
Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product.
▪ Do not use Sikasil®-670 Fire on natural stone.
Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant.
▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools.
▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion.
▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaTitan®
258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner.
Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program.
Product Benefits
- Primerless to glass
- One-component formulation
- Cold application
- Good application properties such as bead stability / good non-sag properties
- Short cut-off string
- Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts)
Areas of Application
SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use.
Technical Product Data
Chemical base 1-C polyurethane
Colour (CQP1) 001-1) Black
Cure mechanism Moisture-curing
Density (uncured) (CQP 006-4) 1.1 kg/l approx.
Non-sag properties (CQP 061-1) Good
Application temperature +5 to +40°C Skin time2)
(CQP 019-1) 40min. approx.
Open time2)
(CQP 526-1) 30min. approx.
Curing speed(CQP 049-1)
Shore A hardness (CQP 023-1 / ISO 868) 51 approx.
Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx.
Elongation at break (CQP 036-1 / ISO 37) 650% approx.
Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx.
Safe Drive-Away Time2)
(cars) with double side airbag
according to FMVSS 212 / 208 (CQP 511-1) without airbag
6 hours
2 hours
Chemical Resistance
SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents.
Method of Application
Removal of old glass
Remove damaged glass in accordance with the vehicle manufacturer’s instructions.
Surface preparation
Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner.
Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection.
Application
Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below).
The substrate temperature must be between 5°C and 35°C.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal®-401 Aquarium
Premium one-component aquatic life safe silicone sealant
SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties.
Extreme temperature resistance (-50°c to +250°c)
Excellent vibration, UV and weathering resistance
Good gap filling properties
Usage
Fish tanks
Water pumps
Aluminium
Glass
Advantages
Extreme temperature resistance (-50°c to +250°c)
Excellent vibration, UV and weathering resistance
Good gap filling properties
Highly versatile
Easy to apply
Aquarium safe
Composition
1-C Silicone (acetoxy)
Shelf life
18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions.
Storage conditions
Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Density
~1.02 kg/l
Application
Application steps
SUBSTRATE PREPARATION
Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry.
CLEANING OF EQUIPMENT
Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife.
PRODUCT INFORMATION
Composition 1-C Silicone (acetoxy)
Packaging 75g Tube, 12 Tube per box
Colour Clear
Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions.
Storage conditions Must be stored in dry conditions and protected from direct sunlight at
temperatures between +10ºC and +25ºC.
Density ~1.02 kg/l
Shore A Hardness ~23
Tensile Strength 1.0 N/mm2
Secant Tensile Modulus 1.1 n/mm2
Elongation at Break ~500%
Ambient Air Temperature +5°c to +45°c
Curing Rate ~3mm per 24 hours
Skinning time ~7-10 minutes
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond is a high strength contact adhesive that will not slump on vertical surfaces. It can be used as a one way liquid adhesive, or a two way contact adhesive, on a variety of surfaces.
Uses SikaBond can be used on most substrates due to its excellent adhesion.
These include:
Floor and wall panels.
Wood, plasterboard and chipboard.
Aluminium, iron and steel.
Concrete, cement sheeting and masonry.
Advantages
One component ready to use.
Fast drying time.
Easy to use.
High adhesion strength.
Non-slump.
Storage and Shelf Life
Stored in the original sealed packaging at temperatures of between 5ºC and 35ºC, this material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking must be removed and light sanding is recommended.
Application
One Way Method:
This method is recommended for heavier panels or where load or stress is expected. Apply a 4 to 6mm bead of SikaBond using a cartridge gun, making sure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges.
Two Way Method:
Apply adhesive as in one way method, bring together substrates, and press firmly over entire surface to transfer adhesive. Then pull apart. Allow adhesive to tack off for 3 to 5 minutes depending on weather conditions, reposition the objects and press together firmly. The surfaces should be tapped together with a hammer and a padded block to ensure maximum contact. Maximum bond strength will be achieved in 12 to 72 hours, depending on substrates and weather. Heavy panels may require temporary mechanical fastening until maximum strength is achieved.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Instant set, high viscosity, multipurpose super glue
Suitable for bonding substrates with irregular surfaces and in vertical applications
Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals
Controlled dosage applicator nozzle
Use:
As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials
Can be used on porous substrates such as porcelain and china
Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc.
Surfaces with small irregularities max. 0.5 mm
On vertical surfaces
Characteristics and Advantages
One Component
Easy to apply, non-sag, gel consistency
Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card
Low consumption adhesive
Versatile, allows adhesion between different materials
Colourless
Durable
Packaging
3 g Tube
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Sika High-Strength for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Fixing studs, battens, and sheets
Filling small gaps while bonding
Fast installation where speed saves labour
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Timber and masonry
Concrete and fibre cement
Many building materials except PE and PP
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications.
Temperature and environmental performance
Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength.
Uses:
SikaBond Fast can be used on most substrates due to its excellent adhesion.
These include:
- Fixing polystyrene wall panels
- Replacing loose tiles on walls
- Skirting boards, architraves and trims to walls
- Bonding panels to wall studs
- Bonding particleboard, plywood, fibre cement and strip flooring to joists
Advantages :
- Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards”
- Natural wood colour
- Reduces the number of mechanical fasteners required to install floors or walls.
- Can be repositioned for up to 60 minutes after application
- Reduces squeaking associated with nail ride in floors
- Paintable with water-based surface coatings
- Easy to use one component
- Bridges gaps up to 9 mm
- Strong adhesion to metal
- No fumes
- High bond strength and heat resistance
- Flows easily at all temperatures
- Easy cleanup
- Fast initial grab – minimises slippage on vertical surfaces
Storage and Shelf Life
Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years.
Instructions for Use
Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous.
Application
Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges.
Cleaning
The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means.
Technical Data (Typical)
Colour Pale Brown
Specific Gravity ~ 1.4
Skinning Time 20 minutes
Repositioning Time 60 minutes
Full Cure 24 hours depending on conditions
When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation).
Service temperature -5ºC to +90ºC
Packaging 420 gram cartridge (12 cartridges per box)
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® SprayFix: The Ultimate Aerosol Spray Adhesive for Multipurpose Use
High-Performance, Fast-Drying, & Repositionable Adhesive
SikaBond® SprayFix is your go-to aerosol spray adhesive for both temporary and permanent bonding. With its high performance, low odour, and fast-drying time, it's designed for your convenience.
Key Advantages:
Easy to use
Low odour
Dries clear
Fast drying time (approximately 2-4 minutes)
High initial strength
Contains no chlorinated solvents - suitable for indoor use
Repositionable for 1-2 minutes
Applications Include:
Upholstery
Floor Repairs
Furniture Lamination
Art and Crafts (e.g., mounting prints)
Suitable Substrates:
Felts and Fabrics
Metals
Foams
Cork
Most Plastics
Rubber Gaskets
Fibreglass
Wood (e.g., plywood, particle board)
How to Use:
Ensure the surface is clean, dry, and free of dust and grease.
Shake the can well before use.
Hold the can approximately 80-100 mm from the surface and spray lightly.
Allow a few minutes for drying.
Packaging:
Available in 150g and 350g aerosol cans.
Color:
White when applied, clear when dry.
Cleaning of Equipment:
After use, invert the can and press the tip until clear propellant comes out for cleaning. Uncured overspray can be removed with Sika® Colma Cleaner or another suitable solvent.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant
Product Highlights
Fast Skinning
Low Odour
Paintable and Sandable
Resistant to Ageing
Silicone-Free
Product Usage
Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction.
Compatibility
Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates.
Packaging
Comes in a 310 ml cartridge for easy application.
Technical Specifications
Cure Mechanism: Moisture-curing
Application Temperature: 535°C
Shelf Life: 12 months when stored below 25°C
Application and Removal
For detailed application and removal guidelines, consult the manufacturer's manual.
Precautions
This product is intended for use by experienced professionals. Always perform tests for compatibility.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant
Product Highlights
Fast Skinning
Low Odour
Paintable and Sandable
Resistant to Ageing
Silicone-Free
Product Usage
Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction.
Compatibility
Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates.
Packaging
Comes in a 310 ml cartridge for easy application.
Technical Specifications
Cure Mechanism: Moisture-curing
Application Temperature: 535°C
Shelf Life: 12 months when stored below 25°C
Application and Removal
For detailed application and removal guidelines, consult the manufacturer's manual.
Precautions
This product is intended for use by experienced professionals. Always perform tests for compatibility.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex 258 Primerless Glass Adhesive 310 mL is a reliable polyurethane glass adhesive designed for primerless bonding to suitable automotive glass chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 310 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Sikaflex 258 for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Sikaflex 258 Primerless Glass Adhesive 310 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Bonding glass where a primerless system is specified
Automotive and transport glazing carried out by trained users
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Compatible glass substrates
Painted frames and prepared bodywork per Sika guidance
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of observe skin time and install components within this window. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Moisture cure technology forms a strong, elastic bond. Skin forms first, followed by through cure depending on joint depth and humidity.
Temperature and environmental performance
Do not apply below the minimum stated on pack. Maintain adequate humidity for moisture cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Remove fresh adhesive with suitable cleaner. Once cured, trim with a sharp blade using care. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store cartridges cool and dry. Check use by dates before installation in critical work. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-291 Black Marine-Grade Polyurethane Sealant 150mL is a premium, one-component, non-sag adhesive sealant specially formulated for marine environments. It cures on exposure to atmospheric moisture, forming a strong, elastic, and durable bond that resists saltwater, vibration, and weathering. Trusted by boat builders and marine professionals worldwide, Sikaflex®-291 meets International Maritime Organisation (IMO) standards for safety and performance.
Features & Benefits
Marine-grade polyurethane formula with superior adhesion
Excellent weathering and saltwater resistance
Elastic and vibration-resistant for long-lasting seals
Low odour and non-corrosive composition
Can be sanded and overpainted after curing
Maintains flexibility across wide temperature ranges
Where to Use
Sealing and bonding on boats, yachts, and marine structures
Deck fittings, hatches, and hardware installations
Elastic, vibration-resistant joints above and below deck
Bonding wood, metals, primers, coatings, ceramics, and GRP plastics
Important Notes
Not suitable for plastics prone to stress cracking such as Plexiglas or Polycarbonate
Surfaces must be clean, dry, and free from grease or dust before application
Recommended application temperature: 5°C to 40°C
Technical Details
Chemical Base
1-component polyurethane
Colour
Black
Cure Mechanism
Moisture-curing
Density (uncured)
Approx. 1.3 kg/L
Shore A Hardness
40
Tensile Strength
1.8 MPa
Elongation at Break
500%
Temperature Resistance
-50°C to +90°C (up to 180°C short term)
Skin Time
Approx. 60 minutes
Shelf Life
12 months (stored below 25°C)
Packaging
150 mL Tube
For marine sealing and bonding you can trust, Sikaflex®-291 delivers professional-grade strength, flexibility, and durability on every project.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces
100% crystal clear / transparent
Good workability
Very good adhesion on many typical building materials
Use:
Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including:
Plasterboard
Wood surfaces
Painted enamel
Polyester
Plastic
Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions.
CHARACTERISTICS AND ADVANTAGES
100% crystal clear / transparent
Good workability
Low shrinkage during cure
Flexible and elastic
Can be used on damp concrete
Very good adhesion on many typical building materials
COLOUR: Transparent
Product Data
Appearance / Colours Transparent
Packaging 300 g cartridge (290 ml), 12 cartridges per box
Storage Conditions / Shelf-Life
Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Technical Data
Chemical Base Silane terminated polymer
Density 1.05 kg/l approx. (ISO 1183-1)
Tensile Strength 2.0 N/mm2 approx. (ISO 37)
Shore A Hardness 30 approx. (after 28 days) (ISO 868)
Elongation at Break 400% approx. (ISO 37)
Elastic Recovery 70% approx. (ISO 7389)
Tear Propagation
Resistance
4.0 N/mm approx. (ISO 34)
Service Temperature −40 °C to +70 °C
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications,
such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed:
Non-porous substrates
Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints.
Porous substrates
Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department.
Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly.
Bonding
After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again.
Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear.
Sealing
After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents.
Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer.
USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction.
Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics.
CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free
Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts
Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic.
Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower
Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only.
Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart.
ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department.
Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility.
RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin!
OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer.
USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction.
Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics.
CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free
Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts
Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic.
Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower
Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only.
Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart.
ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department.
Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility.
RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin!
OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium one component room temperature vulcanising silicone sealant
USE
Fridge and freezer sealing
Pizza oven sealing
Oven sealing
Aluminium
Glass
CHARACTERISTICS AND ADVANTAGES
High temperature resistance (-50 to 250OC)
Excellent adhesion
Gap filling properties
Heat proof
Vibration resistant
Highly versatile
PACKAGING: 300 ml cartridges
COLOUR: Black
SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking.
Uses
Fridge and freezer sealing
Pizza oven sealing
Oven sealing
Aluminium
Glass
Characteristics / Advantages
High temperature resistance (-50 - 250°C)
Excellent adhesion
Heat proof
Gap Filling properties
Vibration resistant
Highly versatile
Product Data
Colour Black
Packaging 300ml Cartridge, 12 cartridges per box
Storage
18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Technical Data
Chemical Base 1-C silicone
Density (uncured) 1.0 kg/l approx.
Skin Time 10 min approx.
Tack-free time 20 min approx.
Curing Time 24 hours approx.
Cure Mechanism Moisture-curing
Cure Type Acetoxy
Application temperature 5 - 45°C
Mechanical/Physical Properties
Tensile Strength 1.0 N/mm2 approx.
Shore a Hardness 25 approx.
Ultimate Elongation 600% approx.
Application Details
Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly.
Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife.
Application Conditions/ Limitations
Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal® Kitchen and Bathroom
SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber.
Uses
Glass and enamel
Ceramics and tiles
Aluminium, steel, zinc, copper
Plastic laminates
Rubber
Stainless steel
Concrete and grouts
Characteristics / Advantages
Excellent adhesion
Great weatherability
Non-sag
Great tooling characteristics
Long-term mould resistance
Interior and exterior usage
Fast curing
Colours
White
Beige
Black
Charcoal
Transparent
Alabaster
Almond Ivory
Off White
Stone
Pewter
Grey
Mid Grey
Stone
Brown
Packaging
300ml cartridges, 12 cartridges per box
Shelf Life
12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Technical Data
Chemical Base: Neutral curing
Density: 0.98 g/cm³ @ 23ºC
Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h.
Curing Rate: 72 hours @ 23ºC/50% r.h.
Consistency: Non-sag
Mechanical/Physical Properties
Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h.
Shore A Hardness: 20 SHA
E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h.
Ultimate Elongation: 300%
Anti-mildew Property: 0 level
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge
Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance.
Key Features
Excellent resistance to chlorinated water and common pool chemicals
Movement accommodation of ± 25 %
Neutral cure — non-corrosive, safe on most metals and tile systems
High elasticity and recovery
Very good resistance to fungal attack
Suitable for interior and exterior applications
Typical Applications
Underwater joints in swimming pools
Wet areas, such as spas, splash zones, and shower recesses
Sealing between tiles, concrete, glass, and metal substrates
Technical Highlights
Service temperature range: –40 °C to +80 °C
Shore A hardness (28 days): ~20
Elastic recovery: > 90%
Typical curing speed: ~2 mm per 24 h
Skinning time: ~5 minutes (23 °C / 50% RH)
Available in White, Grey, and Transparent shades
Shelf life: 15 months (when stored unopened between 5 °C and 25 °C)
Usage & Application Tips
Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease).
Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application.
Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended.
Apply a closed-cell foam backing rod to control joint depth.
Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time.
Allow full cure (minimum 7 days) before filling pool with water.
Limitations & Precautions
This product is not suitable for:
Joints in direct contact with potable food or drink
Overpainting
Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber)
Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Stanley 12mm 240V Corded Hot Glue Gun 25W
Get clean, reliable bonds for crafts, quick household fixes, packaging, and light DIY with the Stanley 12mm Corded Hot Glue Gun. Its 25W heating element warms up efficiently for steady glue flow, while the compact body and ergonomic trigger deliver comfortable, controlled application on a wide range of surfaces.
Why choose this glue gun
Trusted Stanley build for everyday projects and repairs
Consistent glue output for neat, repeatable results
Easy to handle for beginners and experienced makers
Key features
12 mm glue sticks for great coverage and fewer reloads
25W heating element for steady melt and controlled flow
Ergonomic trigger that reduces hand fatigue on longer runs
Built in stand and nozzle shroud to help keep benches tidy
240V corded power for uninterrupted operation
Great for
Cardboard, paper, fabric, felt, foam, ribbons, and craft materials
Wood trims, light plastics, small fixtures, and packaging
General household touch ups and temporary jigs
How to use
Insert a 12 mm glue stick into the feed port.
Plug into a 240V outlet and allow the tool to preheat. A few minutes is typical.
Gently squeeze the trigger to dispense glue. Apply in small beads or dots.
Press parts together while the adhesive is hot. Hold until initial grab occurs.
Rest the tool on the built in stand when not dispensing. Unplug after use.
Compatibility
Uses standard 12 mm hot melt glue sticks. Works with multi purpose, high tack, wood, and craft grade sticks. For heat sensitive substrates such as very thin plastics or delicate fabrics, test on a small area first.
Specifications
Power
25W
Voltage
240V AC
Glue stick size
12 mm diameter
Nozzle
Precision tip with protective shroud
Stand
Integrated flip down stand
Cord
Mains corded
Typical applications
Crafts, packaging, light repairs
What is in the box
Stanley 25W 12 mm Hot Glue Gun
User guide
Glue sticks sold separately
Helpful tips
Keep the nozzle clean by wiping away stringing while warm using a scrap of cardboard.
For porous materials like fabric or raw timber, apply a slightly thicker bead.
For smoother finishes on visible joints, apply small dots and press evenly.
Safety and care
Hot melt adhesive and nozzle become very hot. Avoid contact with skin.
Use on a stable, heat resistant surface. Keep out of reach of children.
Unplug after use and allow to cool before storage.
FAQ
Q: Can I use smaller mini sticks?
A: This tool is designed for 12 mm sticks. Using other sizes can cause feed issues.
Q: How long do I have to position parts?
A: Open time varies by stick type and temperature. Work quickly and test first on your material.
Note: Always test bond strength and heat suitability on an offcut before full application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Stanley Mini DualMelt Hot Glue Gun is a reliable compact dual temperature hot glue gun for craft and light repair chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Stanley Mini for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Stanley Mini DualMelt Hot Glue Gun has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Paper craft and floral work
Bonding trims and beads
Quick household fixes that benefit from a fast set
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Paper, card, fabric
Timber trim
Plastic compatible with hot melt
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of assemble within seconds of application. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Low temp setting helps with delicate materials. High temp setting increases flow and tack for wood and rigid plastics.
Temperature and environmental performance
Operate in dry indoor conditions. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Remove stray strings when cool. Use a silicone mat to catch drips. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Switch off and cool before storing. Keep sticks clean and dry. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sugru is a Multi-Purpose, Mouldable Glue for fixing, Bonding and DIY
Mouldable
Out of the pack, Sugru Mouldable Glues are designed to feel soft and malleable like play-dough. Roll the material in your fingers. Press it where you need it, and mould it by hand into any shape. From an ultra-thin patch to a shock-absorbing bumper, you have 30 minutes to shape it, smooth it, and reposition it as required.
Flexible
Leave for 24 hours. Thanks to some clever science and advanced technologies, Sugru Mouldable Glues react at room temperature, simply on exposure to air. They crosslink into strong, flexible and tactile silicone rubbers overnight. Sugru Mouldable Glues will flex with the materials they're applied to, so you can fix things that need to bend. They work like nothing else on leathers, fabrics or flexible plastics.
Waterproof & Durable
Once cured, Sugru Mouldable Glues are waterproof and long-lasting, just like other silicone rubbers. So you can use them in challenging environments like wet bathrooms, shower and sink areas – even outdoors with long-term exposure to the sun, sea and other weather conditions.
Multi-Material
Sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*.
Strong
Once cured, it stays in its shape permanently and will remain bonded, often for years to come.
Holds Up to 2KG/4.4LB
Ensure surfaces are clean and dry. A 5g/.17oz single-use pack can hold up to 400x its own weight.
Heat and Cold Resistant
Comfortable at high and low temperatures up to 180°C (356°F) and down to -50°C (-58°F).
Durable
Flexibility combined with strong adhesion ensures that your fixes don’t become brittle or crack.
Waterproof
Ensure surfaces are dry before use. It can even be used for sealing applications indoors and out.
Flexible
The thickness of your fix will determine its ultimate flexibility, a thin layer will deliver maximum flex.
Shock Resistant
Excellent dampening properties can deliver vibration resistance and shock protection.
Insulating
Like other silicones, it has good thermal and electrical insulation properties**.
Weatherproof
Excellent ozone and UV resistance. Only slight fading after years in direct sunlight.
Stick It
Sugru sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*.
Mould It
You have 30 minutes to fix, build and create.
Sets Strong
In 24 hours, it turns into a strong and durable silicone rubber that stays stuck.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Get a clean, hardware free look with T-Rex Clear Double Sided Tape. This high performance clear mounting tape creates a strong, permanent bond for photos, hooks, cable clips, house numbers, trims, and light decor. It is ideal when you want the hold without the hardware and a finish that stays virtually invisible on glass, tiles, metal, and painted walls.
Why you will love it
Crystal clear finish that helps hide the fix for a neat result
Strong permanent bond for everyday mounting and craft projects
Moisture and UV resistant construction for long lasting performance
Instant stick with pressure activation, no curing time required
No tools needed, peel and stick application
Great for
Mounting signage, house numbers, and name plates
Securing cable clips and small hooks
Fixing splashback trim and edging
Crafts, scrapbooking, and photo boards
Temporary holding during light assembly
Works on
Glass and mirrors
Glazed tiles and ceramics
Metal, aluminium, and stainless steel
Finished timber and laminate
Painted walls that are sound, clean, and fully cured
Most rigid plastics except low surface energy plastics
Note: Not recommended for wallpaper, delicate or dusty surfaces, or low surface energy plastics such as PE, PP, and PTFE. Always test on a small area first.
How to use
Prepare the surface. Clean with isopropyl alcohol and let dry. Remove dust, grease, and loose paint.
Apply tape. Cut to length. Apply tape to the lightest item first. Press firmly along the whole strip.
Peel liner. Remove the protective liner without touching the adhesive.
Mount. Position carefully. Press firmly for 30 to 60 seconds to activate the bond. Maximum strength develops with time under steady pressure.
Removal tips
Warm gently and peel back slowly at a low angle
Use adhesive remover to clean any residue on robust surfaces
Avoid pulling straight out from the wall to reduce risk of paint lift
Specifications
Brand
T-Rex
Product type
Clear double sided mounting tape
Width
19 mm
Length
4.5 m
Colour
Clear
Adhesive
Acrylic based
Indoor or outdoor
Indoor and protected outdoor applications
Liner
Peel off release film
Good to know
For best results on painted walls, ensure paint is fully cured
Heavier items may need additional strips to spread the load
Use continuous strips near the edges of flat panels to reduce shear
What is in the pack
1 x roll T-Rex Clear Double Sided Tape 19 mm x 4.5 m
FAQs
Can I use it in wet areasYes for sealed, smooth surfaces such as glazed tiles and glass. Avoid constant immersion.
Will it damage paintIt can if paint is weak or not fully cured. Test first and remove slowly with heat to soften the adhesive.
Can it hold shelvesThis tape is ideal for light mounting and trim. Use mechanical fixings for shelves and heavy items.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects.
Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions.
T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger.
Key Features:
All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications.
Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in.
Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold.
Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan.
Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox.
Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability.
Usage Applications:
Home repairs, including fixing broken items and sealing leaks.
Crafting and DIY projects, offering creative flexibility.
Outdoor applications, including camping gear repairs.
Professional job site tasks, providing reliability and strength.
Why Choose T-Rex® Tape?
When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project.
In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
Features
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
FEATURES:
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
R-FLEX TECHNOLOGY
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
Features
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
FEATURES:
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
R-FLEX TECHNOLOGY
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fast, tough and tidy. This bright white duct tape delivers a strong hold for patching, bundling, sealing and quick fixes indoors and outdoors. It tears by hand for easy application and leaves a clean look on light surfaces.
Strong hold for everyday repairs and jobsite tasks
Weather resistant backing that helps shed moisture
UV resistant colour that stays bright in the sun
Hand tear across or along the roll for fast use
Conforms to rough, uneven and curved surfaces
Clean white finish blends with trim, appliances and walls
Great for
Sealing and patching around the home, site and shed
Temporary cable bundling and gear organisation
Quick fixes on tools, hoses, tarps and camping gear
Labelling and marking on light coloured surfaces
Craft, props and event setups where a white finish is preferred
Surface Compatibility
Adheres to most clean, dry surfaces including metal, plastic, painted timber, vinyl, glass, masonry, cardboard and fabric. Not recommended on freshly painted walls, delicate finishes, porous stone or where residue free removal is essential.
How to Use
Clean and dry the surface. Remove dust, oil and loose flakes.
Unroll and press the tape down firmly as you go to avoid air pockets.
For heavy duty holds, wrap or overlap the tape to increase grip.
To remove, lift a corner and peel back slowly at a low angle.
Pro Tips
At cooler temperatures, warm the tape and surface for best tack.
For long term outdoor use, apply to smooth, sealed surfaces.
Test first on sensitive areas to check finish and removal.
Specifications
Brand
T-Rex
Product type
Duct tape
Colour
White
Width
48 mm
Length
9.1 m
Use
Indoor and outdoor
Finish
Matte white
What is in the Box
1 x Roll of T-Rex White Duct Tape 48 mm x 9.1 m
Frequently Asked Questions
Will it hold in the rain?The backing helps resist moisture and the adhesive bonds well to dry, prepared surfaces. Apply to a clean, dry surface for best results.
Is it paintable?Many users paint over duct tape for temporary cosmetics. For the best finish, use a suitable primer and test first.
Will it leave residue?Like most strong duct tapes, residue can occur, especially after long exposure to heat and sun. Test on sensitive finishes and remove slowly.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Tactix 25L Collapsible Storage Crate is a must-have for anyone looking to declutter their space easily and efficiently. Built from high-quality, durable plastic, this crate can hold up to 25 liters of tools, groceries, office supplies, or outdoor equipment, making it ideal for a wide range of uses. The crate’s collapsible design allows it to fold flat for easy storage when not in use, saving valuable space in your home, garage, office, or vehicle.
Whether you're organizing your garage, transporting work tools, or keeping your office supplies tidy, the Tactix 25L crate offers the perfect balance of strength and convenience. The ergonomic handles make it easy to carry, while its lightweight yet sturdy construction ensures long-lasting use. Use it to store gardening tools, sports gear, or even camping essentials—it’s perfect for both indoor and outdoor applications.
When you purchase from Glues Australia, you not only get premium products like the Tactix Collapsible Crate but also exceptional customer service. With fast delivery and a dedicated team ready to assist, we ensure a seamless shopping experience. Shop with confidence knowing you’re backed by Australia’s trusted adhesive and storage experts.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes.
Easy mix
Durable bond
Dries clear
Water resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses.
An all-purpose glue which bonds almost everything
Grabs in minutes - the exact "grab time" depends on the surfaces to be joined
Fast drying
Water resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance.
Incredible bond strength
Waterproof
Superior strength
Adheres to even visibly damp surfaces
Longer work time (10 minutes)
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip Mounting Tape is a double sided, heavy duty, high strength tape that instantly grabs for easy, fast and permanent mounting.
It is ideal for a multitude of surfaces, including metal, wood, rubber, leather, china, brick, stone, plasterboard and most plastics.
Extremely strong
Instant grab
Solvent free
Permanent
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan’s Grip Super Glue is a fast-setting cyanoacrylic acid ester based adhesive. Tarzan's Grip Super Glue dries colourless.
Special multi-purpose formula allows product to bond to a variety of surfaces
Quick-setting
Dries clear, therefore no mess
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL is a reliable two part fast setting epoxy adhesive for durable repairs chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 24 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Tarzan's Grip Grip for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Fast-Set 5 Minute Epoxy Adhesive 24 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Household and workshop repairs that need speed and strength
Fixing fixtures, brackets, and hardware
Filling chips and rebuilding small edges before sanding
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Metal hardware
Ceramic tiles
Most rigid plastics except polyethylene and polypropylene
Timber and MDF
Stone and concrete
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of 3 to 5 minutes working time. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Initial set is reached in about 5 minutes at 23 C. Sandable after several hours. Achieves high final strength after a full overnight cure.
Temperature and environmental performance
Performs well across typical domestic temperature ranges after cure. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean uncured excess with acetone on a cloth. Use care on painted substrates. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Keep sealed to prevent crystallisation. Store upright at moderate temperature. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan’s Grip Multi-Purpose General Adhesive 250 g is a reliable versatile contact style adhesive for crafts and household fixes chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 250 g pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Tarzan's Grip Grip for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Multi-Purpose General Adhesive 250 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Bonding fabric, leather, and rubber
General craft builds
Light repairs around the home
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Leather and canvas
Rubber trim
Timber and some plastics
Card and foam board
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of allow adhesive to tack before assembly as directed on pack. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Forms a tough, flexible bond after solvent evaporation and cure. Press parts together firmly for best adhesion.
Temperature and environmental performance
Keep away from flames and high heat during application. Once cured, it resists typical temperatures. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Use appropriate solvent on uncured adhesive, working in a ventilated space. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Replace cap after each use to reduce skinning. Store below 30 C. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Buzz Indoor Pest Glue Traps 4 Pack
Keep your home clean and comfortable with easy to use, non toxic glue traps that catch crawling pests fast. Each trap folds into a low profile tunnel that protects the sticky surface from dust and keeps pets and little hands away. No sprays, no odour, no mess.
Key benefits
Ready to use traps for ants, cockroaches, spiders, earwigs, silverfish and other crawling insects
Pesticide free adhesive with long lasting tack
Foldable tunnel design for discreet placement
Works in kitchens, laundries, pantries, wardrobes, garages and under sinks
Disposable after use to maintain hygiene
What's included
4 x foldable indoor pest glue traps
Where to place
Along skirting boards and wall edges where insects travel
Near rubbish bins, pet feeding areas and under appliances
Inside cupboards, pantries and storage rooms
Entry points such as doorways and around plumbing penetrations
How to use
Remove a trap from the pack and peel back the protective release paper to expose the glue surface.
Fold along the marked lines to form a tunnel or leave flat if preferred.
Place with the openings along walls or in corners. For best results use multiple traps in larger rooms.
Check weekly. Replace when the surface is covered with dust or insects, or after 4 to 6 weeks.
Pro tips
Reduce competing food sources by wiping crumbs and storing food in sealed containers.
Use additional traps near known pest hotspots for faster control.
Combine with sealing of gaps and cracks for long term prevention.
Disposal and safety
To dispose, fold the trap closed so the adhesive is covered and place in household rubbish.
Keep out of reach of children and pets. If glue contacts skin, remove with cooking oil then wash with soap and water.
Good to know
Indoor use only. Replace regularly for continuous monitoring and control.
Scent free design suits food preparation and storage areas.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes.
Pacer Technology Super Glue Quick Setting Epoxy (SY-QS, SYQS8, T-QS, 15250, 15350) works best on:
All-Purpose
Ceramic
Metal
Pottery
Wood
Tile
Crafts
Fabric
Properties:
Initial colour: Clear hazy to light yellow
Final colour: Light yellow
Set Time: 4-6 minutes @ 65-80F
Handling Time: After 30 minutes
Full Strength: 24 hours
Maximum Gap:25"
Hardness, Shore D: 75-83 (After full cure)
Shear Strength, Steel: 1200 psi ( 20%)
Operating Temperature Range: -40oF to +176oF (-40oC to +80oC)
Use:
1. Surfaces should be clean and dry, free of oil and grease.
2. Roughen surfaces with emery cloth or sandpaper for best results.
3. Dispense from containers following package directions and mix thoroughly approximately 1 minute.
4. Apply mixed epoxy to both surfaces and mate parts together.
5. Remove excess epoxy immediately with denatured alcohol.
6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Timbermate Wood filler is an Interior grade 4 in 1 Wood Putty, Grain Filler, Edge Filler and Crack Filler. When thinned slightly with water can also be used as a sanding sealer. Timbermate does not shrink, sink, crack or fall out and has an indefinite shelf life. It is non-flammable, non-toxic and can be used to the last gram.
The secret ingredient of Timbermate is tap water, therefore, containing no Acrylic, Latex or Solvents. Timbermate comes in 13 premixed colours plus Natural Tint Base. Timbermate takes all types of known stains, varnishes and coatings. The Timbermate formula is over 85 years old and is the only genuine water-based formula in the world proving that the formulation has stood the test of time.
Features & Benefits of Timbermate
No Waste, Usable to the last drop. If tub dries out just add water to soften.
Won't Shrink, Sink, Crack or Fall Out.
Suitable for use in all Timbers including Particle Board M.D.F. (Custom Wood) *Plaster Board, Flooring, Panelling etc.
Can be used as Wood Putty, Sanding Sealer, Prime Coat, Grainfiller, Crackfiller, Undercoat & Edge Filler all in one.
Available in 13 Timber Tones plus Natural. Use White for top coats only.
Can be tinted in wet state or overstained when dry. Use any type of Colorant i.e. Water Based Spirit based ochers etc.
Easy sanding, will not clog paper when DRY Sanded dust can be mixed with water for re-use.
Fast drying approx. 20-30 min, but can be heat dried with a heat gun or lamp for faster drying. Temperature can affect drying time.
Clean hands or tools with water.
Non-Flammable, Non-Toxic, Non-Yellowing.
Solvent, Latex and Acrylic Free.
Heat Proof and Freezeproof.
Provides a strong foundation for all top coats inc. Single & two pack products polyurethane's, oils, acrylics, french polish wax etc.
Takes nails, screws, planing, sawing, drilling and routing
Can be used on Metal, Plastic, Fibreglass and in Foundries.
100% Australian Made and Owned.
Available in pack sizes of 250g, 500g, 2Kg, 8Kg, 20Kg and 200Kg.
Interior Grade.
Edgefiller
Apply TIMBERMATE with a spatula or knife using hand pressure to force into the Edge or End of the grain. For spray gun use stir 10%-15% water into TIMBERMATE fit a 2mm mozzle and set pressure to 60psi. Boards can be stacked for easy spraying. Allow to dry and sand with a fine grit paper and apply topcoat.
Woodfiller/Wood Putty
Fills cracks, knots, pin and screw holes, splits, blemishes, etc. Fill deep holes in layers allowing time for each layer to dry. Will not blind natural wood grain. Drying time is about 30 minutes. TIMBERMATE dries hard and smooth without shrinking or sinking and can be belt or drum sanded as it is not affected by heat, the hotter it gets the harder and faster it sets and that means less "Down Time."
You can speed dry TIMBERMATE by adjusting the surrounding air temperature. This can be done by using either hot air, heat lamps, or kiln ovens.TIMBERMATE can be mixed with any stains before or after the filler is dry. To match medium and darker shades mix with Natural, Pine or other light shades. Use white TIMBERMATE only for white top coats.
Grainfiller
Mix 10% to 15% water into TIMBERMATE to make a perfect Grainfiller, Sanding Sealer and Prime Coat all in one application. First sand surface and with fine grit sandpaper, then apply Grainfiller to surface with a spray gun, paint roller, hessian or a cloth rolled into a ball, rub across the grain in a circular motion finishing with the grain. Sand, once filler is dry, to perfection with either sandpaper or power sander, using a fine grit paper. Grain filer can be used in a Roller or Curtain Coater or Spray Gun using a 2mm nozzle and 60psi pressure. Can be further thinned down with water if required.
MDF
Due to the finishing system used to manufacture MDF, it is essential to seal the job with a water-based non-acrylic product before applying top coats. Therefore TIMBERMATE meets your needs.
Flooring
Preparing old floors: Scrape all dust and waste between boards and surface as well as from knot holes and nail heads, vacuum well and carry out first sanding to prepare for filling and coating. Ensure that floor is stabilised, dry and free of movement.
Application new floors and prepared old floors: Fill cracks, knot and nail holes and all blemished with a putty knife. Fill deeper holes in layers of about 6mm allowing each fill to dry. Apply TIMBERMATE to the entire floor, as a sealant, using a squeegee, trowel or paint roller. Allow to dry and sand off with a fine paper - 120 to 150 grit is recommended for best results. The floor can now be stained or varnished.
Frequently Asked Questions
Question: Is TIMBERMATE toxic, flammable or harmful?
Answer: It is advisable to carry out safe work practices, as you would when working with dust. (Use an approved dust mask and safety goggles). TIMBERMATE contains no harmful ingredients and is non-flammable.
Question: Can TIMBERMATE be used externally?
Answer: No, as TIMBERMATE® is resoluble in water it is not advisable to use it outdoors. TIMBERMATE IS RECOMMENDED FOR INTERIOR USE. For external use, we recommend Earls MulTFill, Powder Putty or Porion Flexible Filler.
Question: Can TIMBERMATE be used with stains and other finishes?
Answer: Yes, TIMBERMATE® will take all types of known stains, coatings and colourants which can be Water based, Oil based, Solvent or Spirit based and even Acid Catalysed Lacquers.
Question: Can TIMBERMATE be grainfilled?
Answer: Yes, TIMBERMATE is a non-solvent based filler and is ideal for grainfilling. Mix 10-15% hot water to thin the Timbermate, then rub over the grain or spread thinly (see below for more detailed instructions). TIMBERMATE will: *Not raise the grain *Not damage the grain TIMBERMATE is: *Easy to sand when dry *Easy to stain when dry *Heat proof so you can speed the drying time by heating with a hair dryer, heat gun, lights etc.
Question: How is the grainfiller applied?
Answer: Take some TIMBERMATE out of the tub and place it in a separate container. Add approximately 10-15% water, (1gm=1ml) and mix into a slurry like paste (like toothpaste). Use a LINT FREE CLOTH AND RUB ACROSS THE GRAIN. When grainfiller goes "whitish" and sands off easily like talc powder, it is dry. TIMBERMATE will not blind the sandpaper (ie. clog up). If sandpaper gets clogged the grainfiller is not dry. Sand off in the same direction as the grain. Stain or coat when dry.
Question: When is the stain applied?
Answer: You can stain before or after applying TIMBERMATE (see "How do I match colours").
Question: How are the colours matched?
Answer: Colour matching is easy. You can do it either of the following ways: Add your colourant to the putty and match the exact colour whilst wet. TIMBERMATE will dry lighter, but coat back to its original wet colour once coated with clear finishes. The final result is what you see (wet) is what you get. You can stain TIMBERMATE once it is dry. To test if dry, just rub sandpaper over putty. If putty clogs the sandpaper the filler is still wet. Wait for TIMBERMATE to dry and then stain.
Question: How long does TIMBERMATE take to dry?
Answer: Depending on the weather and depth of fill, TIMBERMATE will dry as follows: In hot weather, TIMBERMATE dries quicker. In cold weather, the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light.
Question: What depth or width can be filled?
Answer: Do not fill holes deeper than 6-8mm at a time. TIMBERMATE dries quicker when filled in layers. Allow TIMBERMATE to dry between layers.
Question: Why is the tub hard some days and feels dry and soft on other days?
Answer: TIMBERMATE is waterbased. It contains no harmful solvents or acrylics and is, therefore, temperature sensitive. The warmer the weather or environment the softer the putty. On hot days it will start to dry in the tub if not properly sealed. Add a few drops of water to re moisten.
Question: How is TIMBERMATE softened?
Answer: Add a few drops of warm water to the top of the tub. It will soften quite quickly. If tub is frozen, thaw out by standing tub in a tub of hot water or place in a microwave for 20 seconds. TIMBERMATE is freeze thaw stable.
Question: Can TIMBERMATE be used for any other purpose other than wood repair?
Answer: TIMBERMATE does not shrink, sink, crack or fallout and can, therefore, be used on Plasterboard, Masonry, Fibreglass, Plastic and any other surface. Bearing in mind that steel must be coated with a primer to avoid rusting.
Question: Can TIMBERMATE go off or does it have a shelf life?
Answer: TIMBERMATE has an unlimited shelf life and will last indefinitely. If contents become dry merely add a few drops of water to reconstitute. DO NOT add more water than is necessary or leave excess water in the tub for a long period of time. The trapped excess water in the tub will cause the putty to become contaminated and will start to degenerate.
Question: Why are so many colours available?
Answer: We manufacture 13 colours to match almost all shades and types of timber. If you are using a clear coat you must match your putty colour. If staining, use Natural (tinting base).
Question: What is Tint Base (Natural) putty and why?
Answer: Tint Base (Natural putty) is putty in its natural state uncoloured. You may add the lightest shade of tint to change its colour.
Question: Can TIMBERMATE be used on floors?
Answer: TIMBERMATE is ideal for filling cracks, gaps, and nail holes in floors. TIMBERMATE will enhance the grain on the floor. As it does not shrink, sink, crack or fall out it is highly recommended for all floors.
Question: Can TIMBERMATE be used with French Polish and Waxes?
Answer: You can use all types of Waxes, Shellac and Oils on TIMBERMATE.
Question: How is an incorrect match or badly filled hole fixed?
Answer: Errors can be fixed with ease. If TIMBERMATE is not coated then wash out. If already coated, then break the top coat and then wash out. Refill or rematch if necessary.
Question: Is TIMBERMATE Australian owned and manufactured?
Answer: Yes. TIMBERMATE is 100% Australian owned and manufactured. An all Australian dedicated workforce does all manufacturing in our Melbourne factory.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](//gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
![Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]](//gluesaustralia.com.au/cdn/shop/files/Sikasil_pool_white.webp?v=1760227901&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Grey]](//gluesaustralia.com.au/cdn/shop/files/4063565057892.jpg?v=1754724118&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Red]](//gluesaustralia.com.au/cdn/shop/files/4063565066757.jpg?v=1754724118&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](//gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](//gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](//gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](//gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](//gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](//gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](//gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](//gluesaustralia.com.au/cdn/shop/files/949_1005_f9e8bad8-cc2d-4f12-888b-f7be3932182b.jpg?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](//gluesaustralia.com.au/cdn/shop/files/93152845_75d61b67-9ac6-4739-9648-1e850e68af71.png?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](//gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](//gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
![Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]](http://gluesaustralia.com.au/cdn/shop/files/Sikasil_pool_white.webp?v=1760227901&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Grey]](http://gluesaustralia.com.au/cdn/shop/files/4063565057892.jpg?v=1754724118&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Red]](http://gluesaustralia.com.au/cdn/shop/files/4063565066757.jpg?v=1754724118&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
![Timbermate Woodfiller putty crack filler Interior 2Kg [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/9315284002000.jpg?v=1754811488&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/949_1005_f9e8bad8-cc2d-4f12-888b-f7be3932182b.jpg?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_75d61b67-9ac6-4739-9648-1e850e68af71.png?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)