Products
-
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
Selleys Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
-
Selleys Selleys Sugar Soap Cleaner Concentrate 1L Makes 80 litres
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$6.00
-
Selleys Selleys Sugar Soap Wall & Surface Cleaning x 25 Wipes
The trusted cleaning performance of Selleys Original Sugar Soap is brought to you in a quick and easy-to-use format that is ideal for cleaning the walls and surfaces around your home. Features Large wipe: 200mm x 300mm Strong interlaced cloth Specifically designed for painted walls Dual-sided: smooth side for surface wiping, textured side for deeper clean Contains Selleys Original Sugar Soap Everyday use Where can this product be used? Walls (especially painted walls) Kitchen surfaces and appliances Bathroom & laundry tiles, shower screens, basins, bathtubs & appliances Directions Open resealable lid. Slowly peel back the resealable sticker. Pull out wipe from pack. For surface cleaning, use smooth side and simply wipe clean. For a deeper clean, use textured side and wipe up & down or in a circular motion. Reseal the sticker and close the lid to keep remaining wipes fresh and ready for next use. Dispose of used wipe in the rubbish bin. Advice Do not use on prints, signs, dial marks and clear plastics Wipe off immediately from brass and painted surfaces Excessive hard rubbing of low sheen or flat paints can result in glossy patches. Test suitability in an inconspicuous area before using. Safety Tips Keep out of reach of children. Avoid contact with eyes. If in eyes, or if skin irritation occurs, rinse thoroughly with water.
$6.00
-
Selleys Selleys Super Gel Glue Adjustable 30sec - 4 x 1g
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 1g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$9.59
-
Selleys Selleys Super Gel Glue Adjustable 30sec 3g
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 3g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$4.00
-
Selleys Selleys Water Shield Silicone Water repellent for Clothes, shoes, camping
Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort. Key Features Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements. Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear. Where to Use Sportswear, such as ski parkas, gloves, etc. Athletic shoes, including sandshoes and jogging shoes. Camping gear, like tents and sleeping bags. Cloth and canvas bags. Umbrellas. Outdoor furniture, e.g., canvas chairs. Paper maps and plans. Suitable for the Following Materials: Fabric Canvas Nylon How to Use Preparation: Ensure that the item to be treated is clean and dry. Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface. Spray: Use a sweeping motion to spray until the surface is moist. Dry: Allow approximately 3 hours for drying before using the item. Limitations Not suitable for leather or suede articles. Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®. Do not apply to areas that don't require protection (e.g., soles of shoes). Handy Tips Test for colorfastness in an inconspicuous area before full application. Start spraying light-colored areas first, followed by darker areas. Launder or dry-clean soiled articles as usual and reapply the Water Shield. Specifications Size: 200g Aerosol Can Color: Colourless Technology: Silicone-Based Use: Suitable for both interior and exterior applications Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!
$21.00
-
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](//gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
Selleys Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout) The product also contains fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour so can be used in any environment without discomfort. Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam. Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. Temperature resistance – approximately -60°C +150°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Where can this product be used? Showers and sinks. Metal, copper and brass fittings. Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper and brass fitiings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal. Handy tips Tips for Using a Silicone Sealant in a Wet Area Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$11.00
-
Selleys Selleys Wet Area Matt White Ultimate 100% Silicone Sealant for Waterproof, Mould-Resistant Sealing in Bathrooms, Kitchens & More!
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
-
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](//gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
Selleys Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$0.00 - $16.00
-
Selleys Selleys Wet Area Silicone White – Mould-Resistant Silicone Sealant for Wet Areas (90ml Tube)
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer. The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time. Where can this product be used? Showers screens Baths Spas Sinks Plumbing Fixtures What materials is this product suitable for? Ceramic, glazed and porcelain fixtures Metal, copper and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Clean surface with mineral turpentine and dry. Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun. Apply with steady pressure, ensuring sealant is pushed into joint. Tool with a spatula dipped in detergent water within 5-10 mins of application. Clean up with mineral turpentine before product skins. Sealant will cure in 72hrs. Limitations: Not paintable. Complete painting 7 days prior to applying sealant. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. Not suitable for aquariums. Not suitable for food or drinking water contact. Not suitable for permanent water immersion. Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. *Warranty Information Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$11.00
-
Selleys Selleys Wet Area Waterproof Silicone Sealant White 300g (3 Pack)
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. Safety Tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$47.44
-
Selleys Selleys White For Life Ready to use Grout Brilliant White 1.4Kg
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*. Provides superior water resistance, mould and soap scum resistance White For Life – Always looks like new* Resists yellowing, staining and blackening* Crack resistant Sand free - resists scratching files Suitable for indoor wall and floor tiles Comes in a cartridge for minimum wastage Where can this product be used? Bathrooms Showers (walls only) Toilets Laundries Kitchens What materials is this product suitable for? Ceramic tiles Porcelain tiles Stone tiles Most other tiles Please contact your store to confirm avaliability, as some stores may have a limited range. How to Use Preparation For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult. Application Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time. Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint. Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets. Allow grout to firm up in joints for approx 20 min (longer in colder conditions). Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints. Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks. overage 1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). 1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm). Limitations: Not for areas frequently immersed in water eg. Shower floors. Allow to dry for 3 days before exposing grout to water on shower walls. Handy tips If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas. *To maintain whiteness and long term stain & mould resistance: Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard. Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners. Areas subject to high foot traffic will require frequent cleaning. Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes. Coverage guide 1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) 1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm) Clean Up Clean up tools with water before product hardens. Uncured product may be removed with water.
$34.00
-
Selleys Selleys White For Life Ready To Use Grout Cartridge 410g
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs. Surface Preparation: Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants. For new tiling jobs, let tile adhesive set for at least 24 hours. For regrouting, completely remove old grout and thoroughly clean the joints. Application Instructions: Cut the cartridge tip and attach the nozzle. Trim to desired bead width. Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps. Smooth grout using a rubber float or grout applicator, working diagonally. After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze. Avoid over-wetting and excessive wiping, which can weaken the grout lines. After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze. Coverage: Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints) Drying Time: Touch dry in 30 minutes Allow 72 hours before exposing to water in wet areas such as showers Clean-Up: Clean tools and tile surfaces with water before the grout cures Once dry, remove excess grout by mechanical means Technical Data: Colour: White Appearance: Smooth, creamy paste Joint Width: Up to 5mm Water Clean-Up: Yes (before curing) Shelf Life: 12 months if stored unopened in a cool, dry place
$16.00
-
Selleys Selleys White For Life Tile & Grout Cleaner - 750mL
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$19.00
-
Selleys Selleys White For Life Wet Area Waterproof Silicone Sealant 300g
Overview: Selleys White For Life Wet Area Waterproof Silicone Sealant is a premium, 100% silicone sealant designed to provide a long-lasting, waterproof, and mould-resistant seal in high-moisture areas such as bathrooms, kitchens, and laundries. Its advanced formulation ensures the sealant remains brilliant white over time, resisting yellowing, staining, and blackening. Surface Preparation: Ensure all surfaces are clean, dry, and free from dirt, dust, oil, and loose materials. Clean the area with mineral turpentine and wipe dry with a clean cloth before application. Application Instructions: Cut the nozzle at a 45° angle to the desired bead size. Cut the cartridge tip and fit the nozzle. Place the cartridge into a caulking gun and apply steady pressure to ensure the sealant is pushed into the joint. Tool the sealant with a spatula dipped in detergent water within 5-10 minutes of application for a smooth finish. Clean up any excess sealant with mineral turpentine before it skins. Allow the sealant to cure fully, which typically takes 72 hours. Coverage: The coverage depends on the joint size; for example, a 5mm x 5mm joint will yield approximately 12 linear meters per 300g cartridge. Drying Time: The sealant skins in about 10 minutes and cures fully in 72 hours. Clean-Up: Uncured sealant can be removed with mineral turpentine. Once cured, the sealant is extremely difficult to remove and must be abraded or trimmed with a knife. Technical Data: Technology: Acetic cure silicone Colour: White Density: 1.05 g/cm³ Shore A Hardness: Approximately 20 Tensile Strength: 1.5 MPa Elongation at Break: 400% Service Temperature Range: -60°C to +150°C
$17.00
-
Sika Sika AnchorFix-1 Grey Structural Adhesive 300ml
Sika AnchorFix-1 Grey Structural Adhesive 300 ml Overview Sika AnchorFix-1 Grey Structural Adhesive 300 ml is a high quality chemical anchoring adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework. Why choose this product Reliable bond performance supported by proven chemistry and rigorous quality control. Smooth, predictable application that helps reduce mess and cleanup time. Versatile adhesion profile suited to a wide range of substrates and project types. Clear guidance on surface preparation, application method, and curing to help achieve the best possible result. Suitable for residential fit-outs, maintenance, repairs, and light commercial projects. Suitable materials concrete masonry natural stone hollow substrates with sleeves Typical applications General installation, repair, and maintenance where a durable bond is required. Interior work that benefits from a neat finish and tidy joints. Projects where dependable initial grab and high final strength are important. Surface preparation Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting. Application Check ambient and substrate temperature. Observe minimum bond and substrate temperatures specified by the manufacturer. Keep resin warm in cold weather. Cut the nozzle to the required bead size or prepare the container according to the product type. Apply an even bead or spread with a suitable trowel where required. Avoid trapping air. Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting. Support, clamp, or brace as needed until the adhesive develops sufficient handling strength. Cure and working time Cure time depends on substrate temperature. At 20°C typical cure is within a few hours. Do not load anchors until fully cured. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure. Coverage Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces. Limitations Do not apply to surfaces that are visibly wet unless the product specifically allows damp application. Avoid continuous water immersion unless the product is rated for that exposure. Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required. Observe maximum service temperature and any movement or vibration limits appropriate to the application. Clean up Wipe uncured resin with appropriate solvent. Once cured, it is chemically resistant and must be removed mechanically. Always read the product label and follow local regulations for disposal of leftover material and containers. Safety Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information. Storage Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first. Troubleshooting Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure. Slow cure: Verify temperature and humidity. Increase airflow or allow more time. Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins. Frequently asked questions Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first. Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured. What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat. How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes. Why buy from Glues Australia We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
$34.90
-
Sika Sika Anchorfix-3001 Grey Chemical Anchoring Adhesive 250ml
Sika AnchorFix 3001 Epoxy Chemical Anchoring Adhesive 250 ml Sika AnchorFix 3001 is a two part, high performance epoxy anchoring adhesive for fixing threaded rods, bolts, and reinforcement bars into cracked or uncracked concrete and other solid substrates. It delivers very high load capacity, reliable performance in damp concrete, and a long open time that makes placement simple on site. Why choose AnchorFix 3001 High load capacity with shrinkage free cure Works in dry or damp concrete and overhead locations Long open time for easier installation Seismic tested C1 and fire resistant Styrene free and low wastage Approved for contact with drinking water Typical uses Rebar and threaded rod anchoring in new builds and refurbishments Fixing balustrades, handrails, supports, and railings Securing window and door frames and general metalwork Suitable substrates Concrete cracked or uncracked Solid and hollow masonry Natural and reconstituted stone Wood and solid rock Key approvals Complies with NCC reference to AS 5216 design of post installed fastenings in concrete Potable water approved to AS 4020 ICC-ES ESR-3608 for anchoring in cracked concrete under static, wind, and earthquake loading Specifications Chemistry Epoxy, two part 1 to 1 by volume Colour Mixed grey Density Approx 1.49 kg per L Service temperature Long term from minus 40 °C to plus 40 °C Compressive strength Approx 85 N per mm² at 7 days Tensile strength Approx 23 N per mm² at 7 days Mixing Static mixer nozzle supplied, standard sealant gun for 250 ml Packaging 250 ml cartridge Shelf life 24 months unopened at 10 to 25 °C in dry storage Open time and cure guide Substrate or ambient temperature Open time Full cure +25 to +30 °C About 8 minutes About 6 hours +20 to +25 °C About 11 minutes About 7 hours +15 to +20 °C About 15 minutes About 8 hours +10 to +15 °C About 20 minutes About 12 hours +5 to +10 °C Use with warmed cartridge minimum 10 °C About 24 hours How to use Drill the hole to the specified diameter and depth for the anchor size. Clean thoroughly. Blow out dust with oil free compressed air and brush with a steel hole cleaning brush. Repeat the blow and brush steps to remove all fines. Fit the static mixer. Dispense material until a uniform grey appears and discard the first small amount. Inject from the bottom of the hole while withdrawing the nozzle to avoid trapping air. For deep holes use an extension tube. In hollow masonry use a perforated sleeve. Insert the anchor with a slow rotary motion until set at depth. Excess resin should slightly extrude. Do not disturb or load until the full cure time has elapsed for the temperature. Good to know Non sag formula for overhead applications Ensure substrate is sound, clean, and at least 3 °C above dew point Clean tools immediately after use. Cured material must be removed mechanically What is included One 250 ml cartridge with static mixer nozzle. Applicator gun not included. Storage Store sealed in a cool, dry place between 10 and 25 °C. Keep out of direct sun and away from moisture. Safety Read the Safety Data Sheet before use. Wear suitable PPE and provide ventilation. Keep out of reach of children.
$41.95
-
Sika Sika AnchorFix®-1 Pro - High-Performance Styrene-Free Anchoring Adhesive for All Conditions
Sika AnchorFix®-1 is a high-performance, styrene-free chemical anchoring adhesive designed for fast and reliable installations in both construction and DIY projects. This two-component, solvent-free, polyester-based adhesive is ideal for securing rebars, threaded rods, bolts, and special fastening systems in concrete, hollow and solid masonry, hard natural stone, and solid rock. It cures rapidly, even in low temperatures, and can be applied using standard guns. Advantages: Fast curing Compatible with standard guns Usable in low temperatures High load capacity ETA approved Non-sag, even overhead Styrene-free Low odor and wastage Technical Information: Compressive Strength: ~60 N/mm² (7 days, +20°C) Modulus of Elasticity in Compression: ~3,500 N/mm² Tensile Strength in Flexure: ~28 N/mm² Tensile Strength: ~12 N/mm² Temperature Resistance: +50°C (long-term), +80°C (short-term) Glass Transition Temperature: +60°C Color: Component A: White Component B: Black Mixed: Light grey Usage: Ideal for various grades of rebars, threaded rods, bolts, and special fastening systems. Substrates may vary, so testing is recommended to ensure suitability, especially with natural stones. Always ensure the substrate is clean, dry, and free of contaminants. Perform pull-out tests if the substrate strength is unknown. Mixing and Application: Mix the components in a 10:1 ratio by volume. The material must be between +5°C and +40°C for application. Ensure the substrate temperature is between -10°C and +40°C. Shelf Life and Storage: Shelf life is 12 months from the date of production when stored properly. Store in unopened, sealed, and undamaged packaging in dry conditions between +5°C and +25°C. Curing Times: +30°C: Open time 4 minutes, Curing time 35 minutes +25°C: Open time 4 minutes, Curing time 40 minutes +20°C: Open time 5 minutes, Curing time 50 minutes +10°C: Open time 6 minutes, Curing time 85 minutes +5°C: Open time 10 minutes, Curing time 145 minutes -10°C: Open time 30 minutes, Curing time 24 hours Approvals and Certifications: Complies with NCC 2019 reference to AS 5216:2018 for post-installed and cast-in fastenings in concrete. ETA-approved for use in masonry and non-cracked concrete, with CE marking. Cleaning of Equipment: Clean tools with Sika® Colma Cleaner immediately after use. Hardened material can only be removed mechanically. For detailed design considerations, refer to "Technical Documentation Sika AnchorFix®-1" (Ref: 870 43 01).
$38.30
-
Sika Sika Filler 105 Wide Crack Surface Filler Fast Drying Ready to use 250ml
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$15.46
-
Sika Sika Filler 105 Wide Crack Surface Filler Fast Drying Ready to use 400ml
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
-
Sika Sika Filler 105 Wide Crack Surface Filler Fast Drying Ready to use 5L
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$88.91
-
Sika Sika Filler 107 Interior & Exterior 0-4mm Wet Area 250ml
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$16.43
-
Sika Sika Filler 107 Interior & Exterior 0-4mm Wet Area 400ml
SIKA® FILLER 107 | PLASTER FILLER Premium, wet area, fine surface filler Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms Application thickness up to 4mm per layer Suitable for use in exterior situations when overpainted USE Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc. CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying Not sensitive to moisture Appearance / Colours Grey / blue, grey paste Packaging 500 ml plastic tube 5 l and 10 l plastic pail Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion Density ~ 1.050 kg/l Solid Content ~ 62% Grading Dmax : 0.15 mm Layer Thickness 4 mm max. Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-107 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: 2 to 4 hours (thicker applications might require longer time) Paintability: Approx. 12 hours
$21.53
-
Sika Sika Fine Surface Filler Filler-101 Interior Grade 0-3mm 250ml
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$16.13
-
Sika Sika Fine Surface Filler Filler-101 Interior Grade 0-3mm 400ml
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$21.47
-
Sika Sika Fine Surface Filler Filler-101 Interior Grade 0-3mm 5L
SIKA® FILLER-101 | FINE SURFACE FILLER Premium, fine surface filler Very fine consistency for fine surface filling Application thickness up to 3mm per layer Fast drying and easy to sand USE Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc. Smooth finish CHARACTERISTICS AND ADVANTAGES Ready to use, no mixing required Easy application High initial tack or grab on plaster and concrete Quick drying COLOUR: White Appearance / Colour White paste Packaging 500 ml plastic tube Storage Storage Conditions / Shelf-Life 12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost. Technical Data Chemical Base Filled styrene-acrylate dispersion. Density ~ 1.100 kg/l Solid Content ~ 55% Grading Dmax : 0.12 mm Layer Thickness 3 mm max. Application Details Consumption This depends on the substrate roughness and thickness of the layer applied. As a guide, ~ 1 l of Sika® Filler-101 can fill ~ 1 m2 per mm thick. Substrate Quality Clean, free from dust, dry and oil. Application Conditions / Limitations Substrate Temperature +5°C min. / +35°C max. Ambient Temperature +5°C min. / +35°C max. Application Instructions Mixing Sika® Filler-101 is supplied ready to use - no mixing is required. Application Method / Tools Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed. Waiting Time / Overcoating Drying Time: ~ 2 hours Paintability: ~ 4 hours Value Base All technical data stated in this Product Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control.
$94.64
-
Sika Sika Firerate Intumescent Resistant Joint Sealant 310ml
Sika Firerate is a gunnable acrylic based jointing and sealing compound specially formulated with inorganic fillers to provide a fire barrier. Sika Firerate has been tested for fire resistance for up to 4 hours according to AS 1530.4 in masonry wall and floor joints. USE Sika Firerate is suitable for sealing joints in concrete or masonry that must have a fire rated resistance to Australian Standards. Sika Firerate also fulfils the basic function of a gap filler and joint sealant against water and dust penetration. CHARACTERISTICS AND ADVANTAGES Safe to use – contains no asbestos or fibres. Paintable. Good flexibility and adhesion to concrete and masonry. Interior use only. Easily applied with normal caulking equipment. Easy tooling off. Economical – single product for both fireproofing and sealing functions. Water clean-up of tools and equipment while still uncured. Excellent acoustic performance, test report available. COLOUR Grey CHARACTERISTICS/ADVANTAGES • Up to 4 hours fire resistance according to AS 1530.4 • Very good resistance to weathering • Movement capability of ± 20 % • Easy to smooth and very good workability • Good adhesion to many different substrates • Water clean-up of uncured sealant . APPROVALS / STANDARDS • AS 1530.4 FRL • ISO 717.2 Rw (Ctr) = 64 (-13) SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sika® Firerate adheres without primers and/or activators. APPLICATION METHOD / TOOLS Sika® Firerate is supplied ready to use. After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sika® Firerate into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sika® Firerate sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Water can be used if wet tooling is required. CLEANING OF TOOLS Clean all tools and application equipment immediately after use with water. Once cured, residual material can only be removed mechanically LIMITATIONS • Sika® Firerate may be overpainted with solvent free paints. • Do not use Sika® Firerate on damp and/or wet substrates. • Do not apply Sika Firerate at temperatures below 5ºC • Do not use Sika® Firerate to seal joints in and around swimming pools. • Do not use Sika® Firerate to seal joints in external applications on non-porous substrates. • Do not use Sika® Firerate for joints under water pressure or for permanent water immersion. • Do not expose uncured Sika® Firerate to rain or water as this may interfere with the curing reaction. BASIS OF PRODUCT DATA All technical data stated in this Data Sheet are based on laboratory tests. Actual measured data may vary due to circumstances beyond our control. ECOLOGY, HEALTH AND SAFETY For information and advice on the safe handling, storage and disposal of chemical products, users shall refer to the most recent Safety Data Sheet (SDS) containing physical, ecological, toxicological and other safety related data.
$25.69
-
Sika Sika Showerbond shower wall lining adhesive fast curing 300ml
Showerbond is a solvent based, fast grab, gun grade adhesive. It has been specifically formulated for bonding plastic shower linings to gypsum plasterboard or fibre cement wall linings, as well as timber. Use Showerbond is used for bonding plastic shower linings to wall linings. Advantages Fast curing. Will not damage plastic shower liners. Panels can be relocated for up to 30 minutes after positioning. Excellent adhesion to most common building materials. Easy to apply and clean up. Recommended for use with Seratone Silverseal, Clearlite Showers, Duracryl® ,and Athena Showers Product Data Form: Smooth paste Colour: Green Storage & Shelf Life: Twelve (12) months when stored in original unopened containers in a cool, dry place away from naked flames. Packaging: Showerbond is supplied in 300 ml cartridges. Technical Data Solids content: 65% approx. by weight Cure type: Solvent release Cure rate: 24 hours @ 20C Application temperature: 5C to 35C Skinning time: 1 minute Relocation time: Up to 30 minutes, depending on temperature and ventilation Flammability: Flammable solvents are released during cure Toxicity: Non toxic when cured Movement accommodation: Slight, will accept normal building movement Coverage: On average, one cartridge of Showerbond will supply 20 metres of 5 mm bead. Application Conditions Surface Preparation Ensure both surfaces to be bonded are clean, dry and grease free. Cut nozzle on cartridge as shown below so that a 5-6 mm bead will be extruded. Application Apply a 5-6 mm bead in vertical lines at 100 mm centres onto substrate, and apply continuous bead within 15 mm of the perimeter line of the shower lining. Place shower lining onto wall within 10 minutes and firmly press the entire sheet with your hands so that full contact is made with all beads of adhesive. Brace the lining as required in the shower manufacturer's installation instructions. Bracing if required should remain in position for not less than 18 hours. The shower should not be used for at least 24 hours after the wall lining has been installed. Do not apply blobs of adhesive. These will cause unsightly undulations and buckles in the sheet.
$19.07
-
Sika Sika SikaBond 115 MaxTack High Strenght Adhesive Water Based
SikaBond®-115 Max Tack is a 1-part construction adhesive with high final strength, designed for bonding most construction material substrates. It is suitable for internal and sheltered outdoor use. Key Features: Easy to apply Easy to clean Rapid build-up of strength High final strength Very low emissions (Acrylic dispersion) Applications: Ideal for bonding various construction components, including: Skirting boards Wooden frames Battens Mouldings Panels Terracotta tiles Anodised aluminium Polystyrene mouldings and ceiling tiles Bonds well to materials like: Concrete Mortar Fibre cement Wood Painted surfaces Shelf Life & Storage: Shelf life: 18 months from production date. Storage conditions: Store in original, unopened, undamaged packaging in a dry environment, at temperatures between +5°C and +25°C. Technical Details: Density: ~1.40 kg/l (ISO 1183-1) Application Instructions: Follow standard building and construction practices when applying SikaBond®-115 Max Tack. Substrate Preparation: Ensure the substrate is clean, sound, dry, and free from contaminants like oil, grease, cement laitance, old sealants, and loose paint. Remove dust and friable material through wire brushing, grinding, sanding, or other mechanical methods. For best results, follow these priming and pre-treatment steps: Non-Porous Substrates: For surfaces such as aluminium, anodised aluminium, stainless steel, PVC, and glazed tiles: Slightly roughen the surface using a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Wait 15 minutes before applying adhesive (within 6 hours). For metals like copper, brass, and titanium-zinc: Clean and pre-treat using Sika® Aktivator-205. After 15 minutes, apply Sika® Primer-3 N by brush. Wait at least 30 minutes (within 8 hours) before applying adhesive. Porous Substrates: For concrete, aerated concrete, mortars, and bricks: Prime the surface with Sika® Primer-3 N. Wait at least 30 minutes (within 8 hours) before applying adhesive. Note: Primers are adhesion promoters and are not a substitute for proper surface preparation. They also enhance the long-term bond strength. Cleaning of Tools: Clean tools and equipment immediately after use with Sika® Remover-208. For skin cleaning, use Sika® Cleaning Wipes-100. Once cured, the adhesive can only be removed mechanically. For more information, please consult Sika Technical Services.
$17.40
-
Sika Sika Sikabond 145 SuperGrip Adhesive 30 min White 310ml
SikaBond®-145 SuperGrip Premium polyurethane construction adhesive with fast build up of Strength SikaBond®-145 SuperGrip is a premium grade one-component polyurethane construction adhesive with good initial grab and high strength after 30 minutes^. SikaBond®-145 SuperGrip is a versatile, ready to use, fast curing, general purpose construction adhesive suitable for interior and exterior use. One-component. Interior & exterior. Non-shrink. Usage SikaBond®-145 SuperGrip is suitable for use in construction and repair applications where a permanent strong bond is required between porous-nonporous surfaces. SikaBond®-145 SuperGrip is suitable for bonding most common construction materials such as: Wood MDF Concrete Brick Metal Polystrene Polyurethane foam Some PVC Marble Granite Ceramic LOSP Timber Advantages One-component. Interior & exterior. Non-shrink. Non-sag. High initial grab. Adheres rapidly. Stong bond in 30 minutes^. Fast cure. Solvent-free. Resistant to heat. Resistant to weathering. Water resistant -D4 according to DIN En 204 Applies white, can dry translucent if applied in thin layers.
$24.15
-
Sika Sika Sikabond High Quality Wood Working PVA Interior & Exterior 5L
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding. Uses SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include: Timber MDF boards Particle boards Ply woods Advantages - Excellent water resistance - High bond strength within 24 hours - Suitable for interior and exterior applications Storage and Shelf Life Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact. Application SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied. Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth. Colour: White Density: 1.08 kg/L
$108.41
-
Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [Black]
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
-
Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [Grey]
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.00
-
Sika Sika Sikaflex 111 Stick & Seal 1-Part Adhesive & Sealant 290ml [White]
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.98
-
![Sika Sikaflex 118 Extreme Grab 290ml [White]](//gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
Sika Sika Sikaflex 118 Extreme Grab 290ml [White]
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$25.60
-
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
Sika Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
-
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
Sika Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]
Multi-purpose adhesive sealant with a wide adhesion range Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals. Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted PRODUCT BENEFITS Bonds well to a wide variety of substrates Resistant to ageing Can be sanded and painted Passes EN45545-2 R1/R7 HL3 Non-corrosive Low odour NSF-approved for incidental food contact Potable water approved (meets AS4020 requirements) Usage Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Surface preparation Surfaces must be clean, dry and free from grease, oil and dust. Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates. Application Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C. Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry. Tooling and finishing Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use. Removal Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin. Overpainting Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
$38.04
-
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
Sika Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]
Elastic adhesive for vehicle assembly bonding Sikaflex®-252 is an elastic 1-component polyurethane adhesive especially designed for bonding large components in vehicle assembly. It is suitable for bonding coated metal, GRP, ceramic materials and plastics. Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties PRODUCT BENEFITS Bonds well to a wide variety of substrates Capable of withstanding high dynamic stresses Good gap-filling properties Can be painted Vibration-damping Electrically non-conductive Usage Sikaflex®-252 is suitable for assemblies that are subject to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminum (including anodized components), sheet steel (including phosphated, chromated and galvanized components), metal primers and paint coatings (2-component systems), ceramic materials and plastics. Seek manufacturer’s advice before using on plastics that are prone to stress cracking. This product is suitable for professional experienced users only. Tests with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
$53.62
-
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](//gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
Sika Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
-
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
Sika Sika Sikaflex 291 Marine Adhesive Sealant [Black]
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
-
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](//gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
Sika Sika Sikaflex 291 Marine Adhesive Sealant [White]
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck. Why Choose Sikaflex®-291 Excellent adhesion to common marine substrates Good ageing & weathering resistance for long service life Elastic to absorb vibration and movement Low odour and non-corrosive Overpaintable and sandable after cure* Available colours: White, Grey, Black *Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area. Typical Uses Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications. Suitable Substrates Wood Metals, metal primers and 2-component paint systems Ceramic materials Plastics such as GRP (fibreglass), etc. Do Not Use On Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate) Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility. Technical Data (Typical) Property Method / Note Value Chemical base — 1-component polyurethane Cure mechanism — Moisture-curing Colour CQP001-1 White, Grey, Black Density (uncured) — ~1.3 kg/L (colour-dependent) Non-sag properties — Good Application temperature Ambient 5 – 40 °C (optimum 15 – 25 °C) Skin time CQP019-1 (A) ~60 minutes Open time CQP526-1 (A) ~45 minutes Curing speed CQP049-1 Depends on temperature & humidity (see TDS) Shrinkage CQP014-1 ~5 % Shore A hardness CQP023-1 / ISO 48-4 ~40 Tensile strength CQP036-1 / ISO 527 ~1.8 MPa Elongation at break CQP036-1 / ISO 527 ~500 % Tear resistance CQP045-1 / ISO 34 ~6 N/mm Service temperature (continuous) CQP513-1 −50 to +90 °C Service temperature (short-term) CQP513-1 +160 °C (4 h), +180 °C (1 h) Shelf life (B) 12 months (store < 25 °C) CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C. Application Guidance Surface Preparation Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates. Application Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity. Optimum substrate and product temperature is 15 – 25 °C. Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment. Tooling & Finishing Tool within the skin time. Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability). Cleaning & Removal Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent. Cured material: remove mechanically (e.g. knife, wire, abrasion). Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin. Overpainting Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting. If the paint requires baking > 80 °C, allow the sealant to fully cure first. Always conduct preliminary trials under manufacturing conditions. Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area. Compliance & Approvals Meets requirements set out by the International Maritime Organization (IMO). Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable. FAQs Can Sikaflex®-291 be overpainted? Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area. What is a “marine grade” sealant/adhesive? Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline. When and why should a primer be used? Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing. What does the Wheelmark indicate? The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED). Which substrates does Sikaflex®-291 bond to? Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate). How do I remove Sikaflex®-291? Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material. Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
$28.97
-
![Sika Sikaflex Pro+ Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sika Sika Sikaflex Pro+ Sealant 310ml
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
-
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](//gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
Sika Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$0.00 - $28.00
-
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](//gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
Sika Sika SikaSeal 300 Glass & Weather Seal [Transparent]
Usage Aluminium Composite materials Panels(ACP) Glass Metals Coated and painted metals Plastics Wood Advantages Excellent adhesion High movement capability Weather resistant Outstanding UV resistance High strength Interior & Exterior Permanent flexibility Colour Transparent
$18.18
-
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](//gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
Sika Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement Good UV resistance Low odour For exterior and interior use USE Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling Filling of cracks on interior and exterior walls (with no permanent water immersion) CHARACTERISTICS AND ADVANTAGES For exterior and interior use High movement capability ±12.5% Good UV resistance Solvent-free, low odour Overpaintable Very good adhesion on most construction materials such as concrete, plaster, wood Possible storage at -10°C for short period of time (max 24h) Conforms to EN 15651-1 F INT EXT
$7.80
-
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](//gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
Sika Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]
DESCRIPTION SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use. USES SikaSeal® Acrylic 100 is suitable for sealing low movement joints around: ? brick ? Concrete ? Plasterboard ? Windows ? Doors ? Ceramic tiles SikaSeal® Acrylic 100 fills cracks and adheres to: ? Glass ? Wood ? Aluminium ? Brick ? Concrete ? Plasterboard ? Ceramic ? Painted surfaces. CHARACTERISTICS / ADVANTAGES Excellent adhesion to most common construction materials. Water clean-up of uncured sealant. Can be sanded back once fully cured if required to give smooth surface finish. Can be painted over using water based paints. Non-toxic
$5.82
-
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
Sika Sika SikaSeal Roof & Gutter Silicone Sealant
SikaSeal® Roof & Gutter Silicone Sealant Product Type: 1-component neutral cure roof and gutter silicone sealant Product Overview SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance. Key Features Neutral cure, low odour formula Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber Fast curing with a non-sag formula for easy application Interior and exterior use with a temperature resistance range of -40°C to +150°C High movement capability (±25% for translucent, ±50% for coloured variants) Waterproof seal for durable, long-lasting performance Non-toxic and water-potable approved per AS/NZS 4020:2018 Applications SikaSeal® Roof & Gutter is ideal for: Roof and gutter sealing Sealing polycarbonate roof sheeting General sealing around plumbing fixtures and penetrations Sealing interior and exterior joints Specifications Packaging 300ml cartridge Shelf Life 12 months (if stored properly) Colours Available Translucent, Grey, White, Black Density Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l Shore A Hardness Translucent: ~26, Colours: ~46 Elongation at Break Translucent: ~250%, Colours: ~310% Movement Capability Translucent: ±25%, Colours: ±50% Service Temperature -40°C to +150°C Application Instructions Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish. Important Considerations Do not apply on natural stone or bituminous substrates Not recommended for use under water pressure or in permanent water immersion Pre-test required on stressed polyacrylate and polycarbonate materials May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance) Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure) Packaging & Storage Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions. Contact & Ordering For more information or to place an order, contact us at admin@gluesaustralia.com.au
$13.00
-
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
Sika Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]
Usage Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates. Advantages Up to 4 hours fire resistance according to AS 1530.4 Up to 4 hours fire resistance according to EN 1366-4 Very good resistance to weathering Movement capability of ± 35% (ASTM C 719) Easy to smooth and very good workability Good adhesion to many different substrates Neutral curing Colour Grey
$27.35
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 252 High Strength Structural Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/7612895456188_c10ea96d-b0be-41ba-a0ee-9656fab35b16.jpg?v=1754711652&width=645)
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](http://gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
You have seen 720 out of 798 products