In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Liquid Nails Rapid Cure is an advanced, high-performance polyurethane construction adhesive that cures in just 10 minutes*. It provides a durable, waterproof bond even when bonding two non-porous surfaces.
Features
Fast cure in 10 minutes*.
More than twice the strength of conventional solvent-based construction adhesives.
Waterproof – Uncompromising durability, with excellent water, weather and heat resistance.
Can be used to bond most materials, and for most interior & exterior applications.
Its advanced formulation exceeds the requirements of BS-EN204 D4 for durability.
Resistant (after full cure) to heat to 100 degrees C and cold to -30 degrees C. See “Limitations” below.
Does not drip, sag or string between panels.
Bridges gap up to 5mm hence can be used on rough and ill-fitting construction materials.
Product expands slightly as it cures.
The dried adhesive is paintable.
*Expect longer times for very dry timber, heavier objects and less porous surfaces or in colder weather.
*Limitations – Not suitable for sole fixing or structural bonding.
Where can this product be used?
Liquid Nails Rapid Cure can be used for applications where higher performance characteristics are necessary.
These include applications where:
Extra water resistance is essential. eg. Exterior applications such as decking.
Extra strength is required.
Extra temperature resistance is required. eg. Applications where metal substrates are exposed to direct sunlight.
Plastic substrates which are sensitive to solvent-based adhesives are used.
Metal installations in which solvent-based adhesives will be slow to cure.
Liquid Nails Waterproof is also suitable for typical construction applications such as:
Sheet flooring to joists
Metal or aluminium door strips to floors or walls
Timber or fibre cement sheeting to cement block or brick walls
Masonite
What materials is this product suitable for?
Timber
MDF
Plasterboard
Plastics (Pre-test to determine suitability)
Masonry
Concrete
Particleboard
Metals
Rubber
Tiles
LOSP treated pine
How to use this product
General
Avoid contact with skin. Wear safety glasses, impervious gloves and clothing. Surfaces to be bonded should be free of oil, grease and dust. On wet timber pooled water should be wiped off.
1. Cut cartridge tip, fit nozzle and cut end to desired width (approx 5mm diameter).
2. Apply bead along the length of one bonding surface. On broad surfaces apply beads every 40cm. (‘zig-zag’ beads are more appropriate on surfaces of moderate width; eg shiplap panels.)
3. Position pieces and press firmly together. Fix with sufficient nails, screws or clamping to hold the load and achieve contact over the total bond area. Repositionable for up to 5 mins after fitting.
4. Allow to set for 15-20 mins for porous surfaces before removing temporary fasteners or clamps.*
Liquid Nails Rapid Cure will achieve a full cure in 24 hours.
*Expect longer times for very “dry” timber, heavier objects and less porous surfaces, or in colder weather. Spraying surfaces with a very light mist of water may help speed up the cure.
Handy tips
Gloves should be worn when applying Liquid Nails Rapid Cure. Avoid contact with skin.
Adhesive requires moisture to cure, therefore drying times will vary depending on temperature, humidity and the porosity of materials bonded. Spraying surfaces with a very light mist of water may help speed up the cure.
The product should not be applied below 5°C.
LIQUID NAILS Rapid Cure expands slightly as it cures.
Not suitable for sole fixing for structural bonding.
LIQUID NAILS Rapid Cure should always be used in conjunction with mechanical fasteners in structural, critical or high-stress applications.
Wet LIQUID NAILS Rapid Cure residues can be removed with acetone or mineral turpentine.
Cured or dry LIQUID NAILS Rapid Cure residues can be removed by chiselling, scraping or sanding.
Safety tips
If swallowed, do NOT induce vomiting.
Avoid skin contact. Avoid breathing in vapours.
Ensure you use a well-ventilated area
The product is an eye, skin and respiratory irritant and can potentially cause irritation.
Avoid contamination of waterways. Allow waste or leftover product to completely dry out before disposing of it.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in a cool place.
The adhesive should be used within 6 months after opening.
After use, keep the nozzle on the cartridge.
Liquid Nails Rapid Cure is a polyurethane based adhesive that requires moisture to cure. Wrapping the nozzle in aluminium foil and sealing tightly with tape can prevent moisture exposure for longer storage.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to response to movement allowing a strong bond to be maintained over time.
Features
Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last.
Adheres well to wet and dry timber, so there is no need to wait for the timber to dry.
Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures.
Paintable when dry, to give you a neat, quality finished job.
Doesn’t drip, sag or string, so there is less mess when you are using the product.
Is available in a range of sizes and delivery styles.
Meets requirements specified by Australian Standard AS 2329-1999.
Bridges gaps on rough and ill fitting construction material
Has a life expectancy, when cured, of 20 years
Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene.
Perfect for use:
Sheet flooring to joists
Metal or aluminium door strips to floors or walls
Timber or fibre cement sheeting to cement block or brick walls
Masonite to timber
Wallboard or panelling to wood or metal frames
Cork tiles to timber, fibro or plaster
Tempered hardboard to floorboards
To eliminate the squeaks in tongue & groove boards
Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass
Not suitable for use on Styrene Foam, use Liquid Nails Fast
Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding.
Not suitable for bonding materials in areas which will be constantly damp or wet.
Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere
What materials is this product suitable for?
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Ceramic tiles
Aluminium
Painted surfaces
Timber
Hardboards
Render
Many other building surfaces
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A premium grade high strength construction adhesive that delivers a consistently strong bond on mirror, metal and glass material.
Uses
Ideal for adhering mirrors to walls, metal letterboxes to exterior walls, house numbers to exterior walls, bathroom fixtures to tiles, tool holders on metal shed walls etc.
Liquid Nails Mirror, Metal, Glass is also suitable for use on BHP decorative sheet metals such as Lysaght, Zincalume, Colorbond®, Marviplate®, galvanised metals, Alcan and Comalco aluminium systems.
Technical Features
Will not discolour mirrors
Heat and steam resistance
Adheres metal, glass and mirror well to most surfaces including painted surfaces but not wall coverings
Adheres and forms a durable seal between sheet metals
Gap filling on uneven surfaces
Forms flexible/shock resistant bonds
UV resistant
Low odour during application
Non corrosive
Weather resistant
Application Tips
All surfaces must be clean, dry and free from dirt dust, oil and loose rust. Clean surfaces with mineral turpentine and wipe dry with a clean rag before applying. Painted surfaces should not be flaky or peeling.
Cut tip off cartridge and cut nozzle to suitable size opening (approximately 5mm).
Fit nozzle to cartridge. Place cartridge into caulking gun.
Support bond until adhesive cures sufficiently (at least 48 hours adhesive cures at 2mm depth per day).
APPLICATION FOR MIRRORS
For mirrors up to 6mm thick, apply strips of adhesive 5cm from edges and approx 8cm apart
When mirror is pressed onto the wall, strips of adhesive must not spread into, or touch one another. A gap must remain between them.
Immediately after applying adhesive, place mirror against wall before adhesive skins (within 5 minutes)
The weight must be supported and mirror must be held in place with temporary supports (e.g. with clips or tape) to hold and maintain adhesive contact over the total bond area until sufficient adhesive strength has developed. Normally after 72 hours.
Do not seal around the edges of the mirror for at least a week to allow air circulation and aid the adhesive fully cure
Mirrors should not be fixed directly to unpainted plaster, timber, concrete or brick walls. These surfaces should be painted to prevent potential damage to mirror. Painted surfaces should not be flaking or peeling.
Not recommended for fixing vinyl back mirrors
If in doubt, conduct an adhesion test by curing a little adhesive onto mirror backing for 24 hours. If adhesive can be peeled off, do not proceed.
GENERAL APPLICATION
Apply as for mirrors and press surfaces together immediately
Leave ‘squeeze out ‘ to cure and trim (avoid cutting into the bond)
Support bond until adhesive cures sufficiently (normally after 72hrs). Adhesive cures at 2mm depth per day.
Technical Details and Performance
Indicative information only, not to be used for setting specifications.
Consistency (As applied)
Non-slump, solvent free paste
Curing Mechanism
Very rapidly develops an adhesive bond by reaction with moisture from the air
Curing Rate
2mm depth per day
Skin Forming Time
5-10 minutes (depending on weather conditions)
Service Temperature
–60°C to +150°C
Lap Shear Bond Strength (Aluminium to Aluminium at 1.6mm thick adhesive, 500sq mm bond area)
After 24 hrs: 280KPa
After 48 hrs: 550KPa
After 7 days: 830KPa
Coverage
15 metres of a 5mm diameter bead
Cleaning
Clean all excess adhesive from equipment before it cures with a cloth dampened with mineral turpentine or acetone. Once cured adhesive is extremely difficult to remove and must be abraded or trimmed with a knife
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys N Mastic is a non-hardening, waterproof sealing putty designed for a wide range of applications where long-lasting flexibility is crucial. Ideal for sealing joints, gaps around windows, and roofing, it ensures that structures remain protected from water ingress. The unique formula remains pliable, making it perfect for environments where movement and expansion are expected.
Whether you're sealing an outdoor roof gutter, securing window frames, or filling gaps in an air conditioning system, Selleys N Mastic provides a professional-grade finish with no cracking or crumbling. The product is also suitable for metal, glass, concrete, and brick, making it a versatile solution for residential, commercial, and industrial projects.
N-Mastic is a non-skinning polybutene-based compound. It will remain permanently soft and paste-like.
Uses
N-Mastic is suitable for sealing concealed lap joints between plastics, metals, timber, glass, masonry, and expanded foam panels.
It may be used in the installation of cool rooms, prefabricated construction and gasket sealed windscreens to exclude draughts and water penetration through joints in materials.
Technical Features
Non-hardening – remains permanently flexible to provide a lasting seal
Good adhesion – adheres well to most substrates
Moisture resistance – provides an excellent barrier to moisture vapour
Microbe resistance – resists microbial attack
Low shrinkage – avoids the risk of sealant pulling away from joint surfaces
Wide service temperatures – withstands –40oC to +80oC service conditions
Application Tips
Due to the non-skinning, non-hardening nature of the sealant, N-Mastic should not be used in exposed joints where dirt pick-up or hand contact can be a problem.
As N-Mastic is not elastomeric, it should not be used in areas subject to considerable dynamic stress.
Although N-Mastic is resistant to static pressures, a curing sealant is recommended where this is a critical factor.
N-Mastic is not recommended for sealing lap joints in mobile homes, truck bodies, etc., as significant vibration and flexing occur during travel.
Technical Details and Performance
Indicative information only, not to be used for setting specifications.
Colour
Off White
Specific Gravity
1.4g/mL
Consistency
Non-sag
Slump (MIL-S-8802, @ 32oC )
2.5mm maximum
Viscosity (Brookfield HAF 7/2 @ 25oC )
10,000 – 14,000 Poise
Flash Point
85oC
Storage Life (25oC )
Indefinite
Packaging
Plastic cartridge (410g)
Performance Properties
Shrinkage (% maximum) 5
Service Temperature
–40oC to +80oC
Life Expectancy
Up to 20 years
Clean Up
Sealant may be removed with a cloth dampened with kerosene or mineral spirits
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
How to Use
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
No More Gaps Coloured Gaps
No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability.
Key Features
Long-lasting, colour-matched finish
Suitable for Interior & Exterior use
Available in a great colour range, with no need to paint over (Paintable if required)
Superior flexibility to cope with building movement, hiding cracks and gaps longer
Greater than 350% elongation/stretch and up to +/- 20% movement capability
Good resistance to weathering
Superior adhesion to a broad range of surfaces, resulting in a lasting finish
Mould and mildew resistant
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles (not exposed to water)
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Bare or painted surfaces
Colorbond
Many other building materials
How to Use
Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk.
Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun.
Hold the caulking gun at a 45° angle and apply, forcing the product into the gap.
Smooth with a wet finger or spatula.
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured.
Avoid water contact until fully cured – 72 hours or longer in cold weather.
Limitations
Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps.
Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion.
Do not apply or store below 5°C.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup.
When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler.
If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth.
Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned.
Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting.
Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup.
Clean Up
Water-based, so clean up with water.
Uncured product may be removed with water.
Cured product can be removed by sanding and scraping.
Size
450g Cartridge
Colours
Black
Brilliant White
Brown
Cedar
Charcoal
Coffee
Cream
Ivory
Light Grey
Technology
Water-Based
Use
Interior & Exterior
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Exterior & Weatherboard is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
Has good resistance to weathering
Contains a titanium compound for superior UV resistance.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application)..
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack.
Is formulated for long term resistance to cracking and crumbling.
Is water based, so can be cleaned up with water.
Will not stain building materials.
Where can this product be used?
Between exterior window and door frames
Fascia boards and eaves
Masonry Walls
Tiling
Timber & synthetic weatherboards
Brickwork
Fences
Where shrinkage or movement has caused rigid fillers to crack
Gaps with a maximum width of 25mm & depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Fibre cement sheeting, plasterboard
Masonry
Ceramic Tiles
Glass
Aluminium & other metals
Many other building surfaces
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Exterior is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Also available in easy tube format.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
Has good resistance to weathering
Contains a titanium compound for superior UV resistance.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application)..
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack.
Is formulated for long term resistance to cracking and crumbling.
Is water based, so can be cleaned up with water.
Will not stain building materials.
Where can this product be used?
Between exterior window and door frames
Fascia boards and eaves
Masonry Walls
Tiling
Timber & synthetic weatherboards
Brickwork
Fences
Where shrinkage or movement has caused rigid fillers to crack
Gaps with a maximum width of 25mm & depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Fibre cement sheeting, plasterboard
Masonry
Ceramic Tiles
Glass
Aluminium & other metals
Many other building surfaces
How To Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap.
Smooth with a wet spatula, ensuring sufficient product remains in joint.
Clean up with a damp cloth immediately.
Allow to skin (about 30 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Protect from water until firmly skinned. Allow for longer skin and cure times in damp conditions.
Limitations:
For new weatherboard, check weatherboard manufacturers instructions before using this product
Note that in very harsh conditions, joints between boards may expand beyond products movement capability. In such cases re-apply product and paint over.
Not suitable for areas of continuous water immersion eg ponds
Not suitable for application at below 5°C
Protect from rain until the product has firmly skinned, and allow longer skin and cure times in damp conditions.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats and flat paints may crack on drying. To reduce this effect, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
For maximum durability on bare exterior surfaces, apply a coat of acrylic paint and allow to dry, before applying this gap sealant. Always paint over with a quality exterior paint.
To ensure you get a professional finish ensure you paint with a good quality paint and paint brush. Painting with a good brush ensures the finish and durability of the paint is increased. We recommend a 50mm Edger Brush, as the cut angle of the bristles takes the work out of applying paint.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint.
Features
Available in a great colour range, so no need to paint.
Paintable if required.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage
Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application).
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack
Is formulated for long term resistance to cracking and crumbling.
Is water-based, so can be cleaned up with water.
Will not stain building materials.
Has good resistance to weathering.
Mould and mildew resistance.
Where can this product be used?
Between window and door frames and the wall.
Along skirting boards.
Around cornices.
Between benchtops and tiles which are not exposed to water.
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm.
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Bare or painted surfaces
Colorbond
Many other building materials
How To Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and apply, forcing product into gap
Smooth with a wet finger or spatula
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Avoid water contact until fully cured- 72 hours or longer in cold weather.
Limitations:
Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps.
Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant.
Do not apply or store below 5°C.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
Features
Superior formulation+ that stops mould growth*
Fast skinning formulation which means you can use your shower in 1 hour
Provides a durable waterproof seal
Resists lifting
Where can this product be used?
Suitable for use in humid and damp environments such as
Kitchens
Bathrooms
Laundries
Showers
Basins
tiles
Worktops
Baths & spas
Plumbing fixtures
What materials is this product suitable for?
Ceramic
Glazed & porcelain fixtures
Aluminium
Plastic laminates
Some rubbers
Glass
Stainless Steel
How to Use
Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould
Thoroughly clean surface where sealant will be applied with turps and dry completely
Cut nozzle at 45°angle, cut cartridge tip and fit nozzle
Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint
Tool with a spatula dipped in detergent water within 5-10 minutes of application
Clean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area
#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)
*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth
Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
Tips
For neater joints, mask sides before applying the sealant and remove the tape before sealant skins
Not paintable. Complete painting 7 days before applying the sealant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
Features
Superior formulation+ that stops mould growth*
Fast skinning formulation which means you can use your shower in 1 hour
Provides a durable waterproof seal
Resists lifting
Where can this product be used?
Suitable for use in humid and damp environments such as
Kitchens
Bathrooms
Laundries
Showers
Basins
tiles
Worktops
Baths & spas
Plumbing fixtures
What materials is this product suitable for?
Ceramic
Glazed & porcelain fixtures
Aluminium
Plastic laminates
Some rubbers
Glass
Stainless Steel
How to Use
Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould
Thoroughly clean surface where sealant will be applied with turps and dry completely
Cut nozzle at 45°angle, cut cartridge tip and fit nozzle
Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint
Tool with a spatula dipped in detergent water within 5-10 minutes of application
Clean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area
#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)
*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth
Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
Tips
For neater joints, mask sides before applying the sealant and remove the tape before sealant skins
Not paintable. Complete painting 7 days before applying the sealant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Paint Over Sealant is a permanently paintable sealant.
Features
Paintable
Smooth flawless finish.
Easy to use and can be used on damp surfaces.
Superior adhesion to most building materials.
Low odour so can be used in any environment without discomfort.
Weather resistant by forming a durable seal which remains flexible, not drying or cracking
Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch.
Temperature resistance – approximately -40°C +93°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
May be discoloured by contact with alloys containing brass, copper or zinc.
Do not allow unused product to freeze.
Where can this product be used?
10879.Window frames that need painting
102879.Capstones Masonry walls that need painting
Perfect for use on or around:
Bricks and concrete
Windows frames
Tiled and wooden fixtures
Areas where a sealant is needed and where you want to paint it
Not suitable for use in below waterline applications.
Not suitable for use on oily woods such as cypress, teak or cedar.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Glass
Aluminium
Fibre Cement
Painted Surfaces
Ceramics
Masonry
Most metals
Most plastics
Wood
How to use this product
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant.
Remove the tape before the sealant skins.
For a better finish use a spatula dipped in detergent and water to tool off the sealant.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
To improve the paint finish, wipe the sealant with detergent solution immediately before painting.
Avoid smearing sealant on the surrounding surfaces as this may effects its paintability.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula
Superior flexibility with +/- 25% movement capability
Temperature resistance: approximately -60°C to +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25-year guarantee* against crumbling, cracking, and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm²/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass, and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics, including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula.
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm2/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs.
Features
Easy to use
Strong
Flexible Bond
Weather resistant
Impact resistant
Appearance
Dries yellowish/beige
Where can this product be used?
Sole
Tongue
Strap
Inner sole
Attach beads, jewels, decorative items
Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles.
What materials is this product suitable for?
Leather
Canvas
Fabric
Rubber
Cork
Most Plastics
EVA foam (e.g Desert boots sole)
How to use this product
Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal.
For larger area repairs such as shoe soles, we recommend you use the contact bond method:
For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes).
Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications.
For smaller areas, either use the contact method as above, or join with a wet bond:
Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry.
Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s.
Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries.
Handy tips
A piece of plastic from a takeaway container makes a good applicator for shoe soles.
Bulldog clips are handy to use for clamping straps and other small areas.
Pack includes a removable nozzle for easy application.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler.
Features
Suitable for interior and exterior applications
Good adhesions to most surfaces
Water and weather resistant
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs
What materials is this product suitable for?
Mortar
Masonry
Concrete
Wood
Stone
Primed metal surfaces
Brick
Plaster
Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next.
Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications).
Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints.
Limitations:
Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps.
Avoid using below 5°C or in wet conditions.
Painting with oil-based paints is not recommended until 24 hours after the filler has been applied.
Water-based paints may be used immediately after the filler has set.
If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application.
Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Wallboard
Wood
Masonry
Plaster
Primed nail heads
Plasterboard
Colours White
Technology Water Based
Use Interior
Exterior (when painted)
How To Use
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications).
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Handy Tips
Painting with oil-based paints is not recommended until 24 hours after filler has been applied.
Water based paints may be used immediately after filler has set.
If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping or sanding.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces.
Features
Concentrated – makes up to 30 litres
Professional strength grease & grime cleaner
Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces.
Can be diluted with water or used neat
Where can this product be used?
Kitchen surfaces – to clean floors, walls and cupboards
Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces
Painting & Wallpapering – wash surfaces prior to painting
General Cleaning – appliances, stainless steel, blinds and more
What materials is this product suitable for?
Floors
Tiles
Walls
Benchtops
Cooktops
Appliances
Wipe off immediately from aluminium and brass surfaces
Handy tips
Dilute to suit the cleaning task.
Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose.
For smaller areas or spot, cleaning try Selleys Super Kleen
Safety tips
For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal.
Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes.
The use of rubber gloves is recommended
If swallowed, give a glass of water and see a doctor.
If in eyes, wash out immediately with water
For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The trusted cleaning performance of Selleys Original Sugar Soap is brought to you in a quick and easy-to-use format that is ideal for cleaning the walls and surfaces around your home.
Features
Large wipe: 200mm x 300mm
Strong interlaced cloth
Specifically designed for painted walls
Dual-sided: smooth side for surface wiping, textured side for deeper clean
Contains Selleys Original Sugar Soap
Everyday use
Where can this product be used?
Walls (especially painted walls)
Kitchen surfaces and appliances
Bathroom & laundry tiles, shower screens, basins, bathtubs & appliances
Directions
Open resealable lid.
Slowly peel back the resealable sticker.
Pull out wipe from pack.
For surface cleaning, use smooth side and simply wipe clean. For a deeper clean, use textured side and wipe up & down or in a circular motion.
Reseal the sticker and close the lid to keep remaining wipes fresh and ready for next use.
Dispose of used wipe in the rubbish bin.
Advice
Do not use on prints, signs, dial marks and clear plastics
Wipe off immediately from brass and painted surfaces
Excessive hard rubbing of low sheen or flat paints can result in glossy patches.
Test suitability in an inconspicuous area before using.
Safety Tips
Keep out of reach of children.
Avoid contact with eyes.
If in eyes, or if skin irritation occurs, rinse thoroughly with water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Why Choose Selleys Super Glue Adjustable Gel?
Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes.
Key Benefits:
Adjustable Setting Time: Allows precise alignment before setting.
Rapid Bonding: Bonds in 30 seconds for fast repairs.
Versatile: Adheres to ceramics, china, metal, wood, and most plastics.
Easy to Use: No mixing required, with a convenient gel formulation for clean application.
Where Can This Product Be Used?
Everyday household repairs on:
Ceramic and China
Metal and Wood
Most Plastics*
What Materials Is It Suitable For?
Bonds a variety of porous and non-porous surfaces.
Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers.
How to Use Selleys Super Glue Adjustable Gel
Prepare:
Pierce the seal by attaching the nozzle with the cap and turning clockwise.
Ensure surfaces are clean, dry, and free from dust, dirt, and grease.
Apply:
Apply a small amount of adhesive to the surfaces to be bonded.
Press surfaces together gently and hold for several minutes to ensure sufficient bond strength.
After Use:
Wipe the nozzle clean with a cloth or paper.
Replace the cap securely.
Limitations
Not suitable for use on leather, polyethylene, polypropylene, or PTFE.
Will not permanently bond vessels exposed to water or dishwashers.
Handy Tips for Best Results
Ideal for vertical applications and slightly porous materials.
Use 1 drop per cm² for optimal bonding.
Sets in 30 seconds, achieving maximum bond strength in 24 hours.
Clean-Up Instructions
Wipe the tip of the tube with a cloth or paper after use.
Replace the cap tightly to avoid drying out the product.
Product Details
Size: 1g Tube
Colour: Clear
Technology: Cyanoacrylate
Recommended Use: Interior
Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Why Choose Selleys Super Glue Adjustable Gel?
Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes.
Key Benefits:
Adjustable Setting Time: Allows precise alignment before setting.
Rapid Bonding: Bonds in 30 seconds for fast repairs.
Versatile: Adheres to ceramics, china, metal, wood, and most plastics.
Easy to Use: No mixing required, with a convenient gel formulation for clean application.
Where Can This Product Be Used?
Everyday household repairs on:
Ceramic and China
Metal and Wood
Most Plastics*
What Materials Is It Suitable For?
Bonds a variety of porous and non-porous surfaces.
Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers.
How to Use Selleys Super Glue Adjustable Gel
Prepare:
Pierce the seal by attaching the nozzle with the cap and turning clockwise.
Ensure surfaces are clean, dry, and free from dust, dirt, and grease.
Apply:
Apply a small amount of adhesive to the surfaces to be bonded.
Press surfaces together gently and hold for several minutes to ensure sufficient bond strength.
After Use:
Wipe the nozzle clean with a cloth or paper.
Replace the cap securely.
Limitations
Not suitable for use on leather, polyethylene, polypropylene, or PTFE.
Will not permanently bond vessels exposed to water or dishwashers.
Handy Tips for Best Results
Ideal for vertical applications and slightly porous materials.
Use 1 drop per cm² for optimal bonding.
Sets in 30 seconds, achieving maximum bond strength in 24 hours.
Clean-Up Instructions
Wipe the tip of the tube with a cloth or paper after use.
Replace the cap tightly to avoid drying out the product.
Product Details
Size: 3g Tube
Colour: Clear
Technology: Cyanoacrylate
Recommended Use: Interior
Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort.
Key Features
Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements.
Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear.
Where to Use
Sportswear, such as ski parkas, gloves, etc.
Athletic shoes, including sandshoes and jogging shoes.
Camping gear, like tents and sleeping bags.
Cloth and canvas bags.
Umbrellas.
Outdoor furniture, e.g., canvas chairs.
Paper maps and plans.
Suitable for the Following Materials:
Fabric
Canvas
Nylon
How to Use
Preparation: Ensure that the item to be treated is clean and dry.
Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface.
Spray: Use a sweeping motion to spray until the surface is moist.
Dry: Allow approximately 3 hours for drying before using the item.
Limitations
Not suitable for leather or suede articles.
Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®.
Do not apply to areas that don't require protection (e.g., soles of shoes).
Handy Tips
Test for colorfastness in an inconspicuous area before full application.
Start spraying light-colored areas first, followed by darker areas.
Launder or dry-clean soiled articles as usual and reapply the Water Shield.
Specifications
Size: 200g Aerosol Can
Color: Colourless
Technology: Silicone-Based
Use: Suitable for both interior and exterior applications
Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout)
The product also contains fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away.
Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour so can be used in any environment without discomfort.
Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam.
Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch.
Temperature resistance – approximately -60°C +150°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
Where can this product be used?
Showers and sinks.
Metal, copper and brass fittings.
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper and brass fitiings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine.
Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine.
Avoid smearing on surrounding surfaces, see handy tip.
Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal.
Handy tips
Tips for Using a Silicone Sealant in a Wet Area
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish complete painting prior to use of the sealant as it can not be painted over.
For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas
Key Features
Matt finish for elegant look
100% silicone sealant
25-year guarantee against cracking or peeling
Waterproof seal with superior adhesion
Mould-resistant formula
Non-corrosive, neutral cure
Best For
Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures.
Suitable Materials
Ceramic, Glazed & Porcelain Fixtures
Metal, Copper & Brass Fittings
Plastic Laminates
Rubber
Glass
Stainless Steel
Concrete & Grouts
Many Plastics including Polystyrene
How to Use
Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application.
Limitations
Not paintable
Not suitable for certain materials and uses
Handy Tips
Mask sides for neater joints. Work in manageable sections for a smoother finish.
Clean Up
Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
Additional Info
Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
High-Grade Neutral Cure Silicone
A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots.
Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying.
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour, so can be used in any environment without discomfort.
Easy to clean once applied, as it resists moisture, hot cooking oils, and steam.
Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch.
Temperature resistance: approximately -60°C to +150°C.
25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying.
Where can this product be used?
Showers and sinks
Metal, copper, and brass fittings
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper, and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine.
Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe.
Remove tape before the sealant skins. Clean tools immediately with mineral turpentine.
Avoid smearing on surrounding surfaces.
The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup.
When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish, complete painting prior to using the sealant as it cannot be painted over.
Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish.
Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures.
Safety Tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and Re-Use
Store in cool dry conditions, below 30°C.
The sealant should be used within 6 months after opening.
After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity.
For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge.
If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer.
The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time.
Where can this product be used?
Showers screens
Baths
Spas
Sinks
Plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Clean surface with mineral turpentine and dry.
Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun.
Apply with steady pressure, ensuring sealant is pushed into joint.
Tool with a spatula dipped in detergent water within 5-10 mins of application.
Clean up with mineral turpentine before product skins.
Sealant will cure in 72hrs.
Limitations:
Not paintable. Complete painting 7 days prior to applying sealant.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
Not suitable for aquariums.
Not suitable for food or drinking water contact.
Not suitable for permanent water immersion.
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Work in sections that can be completed before sealant skins.
Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish.
*Warranty Information
Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean Up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by
cutting and scraping.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*.
Provides superior water resistance, mould and soap scum resistance
White For Life – Always looks like new*
Resists yellowing, staining and blackening*
Crack resistant
Sand free - resists scratching files
Suitable for indoor wall and floor tiles
Comes in a cartridge for minimum wastage
Where can this product be used?
Bathrooms
Showers (walls only)
Toilets
Laundries
Kitchens
What materials is this product suitable for?
Ceramic tiles
Porcelain tiles
Stone tiles
Most other tiles
Please contact your store to confirm avaliability, as some stores may have a limited range.
How to Use
Preparation
For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult.
Application
Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time.
Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint.
Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets.
Allow grout to firm up in joints for approx 20 min (longer in colder conditions).
Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints.
Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks.
overage
1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
Limitations:
Not for areas frequently immersed in water eg. Shower floors.
Allow to dry for 3 days before exposing grout to water on shower walls.
Handy tips
If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas.
*To maintain whiteness and long term stain & mould resistance:
Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard.
Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners.
Areas subject to high foot traffic will require frequent cleaning.
Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes.
Coverage guide
1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
Clean Up
Clean up tools with water before product hardens.
Uncured product may be removed with water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs.
Surface Preparation:
Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants.
For new tiling jobs, let tile adhesive set for at least 24 hours.
For regrouting, completely remove old grout and thoroughly clean the joints.
Application Instructions:
Cut the cartridge tip and attach the nozzle. Trim to desired bead width.
Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps.
Smooth grout using a rubber float or grout applicator, working diagonally.
After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze.
Avoid over-wetting and excessive wiping, which can weaken the grout lines.
After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze.
Coverage:
Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints)
Drying Time:
Touch dry in 30 minutes
Allow 72 hours before exposing to water in wet areas such as showers
Clean-Up:
Clean tools and tile surfaces with water before the grout cures
Once dry, remove excess grout by mechanical means
Technical Data:
Colour: White
Appearance: Smooth, creamy paste
Joint Width: Up to 5mm
Water Clean-Up: Yes (before curing)
Shelf Life: 12 months if stored unopened in a cool, dry place
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives.
Surface Preparation:
Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility.
Application Instructions:
Twist the nozzle to spray position.
Spray directly onto the surface.
Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up.
Wipe using a damp sponge or cloth.
Rinse thoroughly with clean water.
For a streak-free finish on glass and taps, dry with paper towel before the surface dries.
Coverage:
Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom.
Drying Time:
Fast-drying; ensure complete rinsing and wiping for optimal results.
Clean Up:
Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces.
Technical Data:
Form: Liquid
Colour: Pale Yellow
Scent: Fresh Lime
Use: Interior (kitchens, bathrooms, showers)
Packaging: 750mL trigger spray bottle
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](//gluesaustralia.com.au/cdn/shop/files/9300697130303_2337373e-0fee-4f3c-a52e-b0464c42720e.png?v=1754711849&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](//gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](//gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](//gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Cream]](//gluesaustralia.com.au/cdn/shop/files/9300697116307.png?v=1754724120&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](//gluesaustralia.com.au/cdn/shop/files/9300697129154_9d32cafb-73fb-4a80-a426-601e1609e6b9.png?v=1754711839&width=645)
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125668_e972750e-da18-4ffa-b723-5fdb36764c7c.png?v=1754711838&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](//gluesaustralia.com.au/cdn/shop/files/9300697123718_ba862328-1e1f-4607-80f6-dbe7568e7040.png?v=1754711835&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](//gluesaustralia.com.au/cdn/shop/files/9300697128966_f7f1ad95-c5c9-4fcb-b790-2ec77b1fecc0.jpg?v=1754711830&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](//gluesaustralia.com.au/cdn/shop/files/9300697115263_d81e146e-2bcf-410a-bcad-ef2cdb518343.png?v=1754711828&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](//gluesaustralia.com.au/cdn/shop/files/9300697128812_e6db645e-770f-466e-b839-e1436d775f7c.jpg?v=1754716162&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](//gluesaustralia.com.au/cdn/shop/files/93006971288_e5c72006-3593-4105-a377-2e2ef8783219.png?v=1754716162&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent]](//gluesaustralia.com.au/cdn/shop/files/9300697128843_fcf51f23-ec41-4a49-aaee-70cab0a2903b.jpg?v=1754711818&width=645)
![Selleys No Mould Silicone Selant 100ml [White]](//gluesaustralia.com.au/cdn/shop/files/9300697128836_d8030407-bb46-4243-8f8f-670a3627cc7e.png?v=1754711816&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697115607.jpg?v=1754724130&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Classic Cream]](//gluesaustralia.com.au/cdn/shop/files/9300697122520.jpg?v=1754724130&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/9300697126047_24fe6e74-fe07-4d10-9db0-38dc98c383c8.png?v=1754711781&width=645)
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/9300697128881_05baffa7-20d9-4ff2-9039-79bd0c8a796b.png?v=1754711779&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697132673_9813d4fc-b7c0-4502-8c30-7f4b7f7d7408.webp?v=1754716190&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697132673_a62141c0-14b4-4be3-9f3d-e9bbf8e3ce89.webp?v=1754716190&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697114952.jpg?v=1754724133&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Off White]](//gluesaustralia.com.au/cdn/shop/files/9300697125002.jpg?v=1754724133&width=645)
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/9300697130303_2337373e-0fee-4f3c-a52e-b0464c42720e.png?v=1754711849&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](http://gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9300697116307.png?v=1754724120&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/9300697129154_9d32cafb-73fb-4a80-a426-601e1609e6b9.png?v=1754711839&width=645)
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125668_e972750e-da18-4ffa-b723-5fdb36764c7c.png?v=1754711838&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697123718_ba862328-1e1f-4607-80f6-dbe7568e7040.png?v=1754711835&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128966_f7f1ad95-c5c9-4fcb-b790-2ec77b1fecc0.jpg?v=1754711830&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115263_d81e146e-2bcf-410a-bcad-ef2cdb518343.png?v=1754711828&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128812_e6db645e-770f-466e-b839-e1436d775f7c.jpg?v=1754716162&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/93006971288_e5c72006-3593-4105-a377-2e2ef8783219.png?v=1754716162&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697128843_fcf51f23-ec41-4a49-aaee-70cab0a2903b.jpg?v=1754711818&width=645)
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697128836_d8030407-bb46-4243-8f8f-670a3627cc7e.png?v=1754711816&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697115607.jpg?v=1754724130&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Classic Cream]](http://gluesaustralia.com.au/cdn/shop/files/9300697122520.jpg?v=1754724130&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697126047_24fe6e74-fe07-4d10-9db0-38dc98c383c8.png?v=1754711781&width=645)
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/9300697128881_05baffa7-20d9-4ff2-9039-79bd0c8a796b.png?v=1754711779&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697132673_9813d4fc-b7c0-4502-8c30-7f4b7f7d7408.webp?v=1754716190&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697132673_a62141c0-14b4-4be3-9f3d-e9bbf8e3ce89.webp?v=1754716190&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697114952.jpg?v=1754724133&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125002.jpg?v=1754724133&width=645)
