In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces. Also available in easy tube format.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
How to Use
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
No More Gaps Coloured Gaps
No More Gaps Coloured Gaps offers a long-lasting, colour-matched finish, suitable for both interior and exterior use. It comes in a wide range of colours, with no need to paint over (although it is paintable if required). It provides superior flexibility to cope with building movement, hiding cracks and gaps longer, with greater than 350% elongation/stretch and up to +/- 20% movement capability.
Key Features
Long-lasting, colour-matched finish
Suitable for Interior & Exterior use
Available in a great colour range, with no need to paint over (Paintable if required)
Superior flexibility to cope with building movement, hiding cracks and gaps longer
Greater than 350% elongation/stretch and up to +/- 20% movement capability
Good resistance to weathering
Superior adhesion to a broad range of surfaces, resulting in a lasting finish
Mould and mildew resistant
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles (not exposed to water)
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Bare or painted surfaces
Colorbond
Many other building materials
How to Use
Ensure the surface is clean, dry, and free from dust, grease, flaking/powdery paint, and old or crumbling caulk.
Cut the seal and nozzle, fit it to the top of the cartridge, and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking Gun.
Hold the caulking gun at a 45° angle and apply, forcing the product into the gap.
Smooth with a wet finger or spatula.
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow surface to skin thoroughly prior to painting with water-based paints. If using oil-based paints or for large gaps, allow the sealant to set for about 24 hours and ensure the product is completely cured.
Avoid water contact until fully cured – 72 hours or longer in cold weather.
Limitations
Not recommended for foot traffic areas, gaps between tongue and groove boards, or weatherboard overlaps. Use Selleys No More Gaps Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards, and Selleys No More Gaps Exterior & Weatherboard Gap Filler for weatherboard overlaps.
Not suitable for areas in prolonged contact with water (e.g., showers, pools, & spas). Use Selleys Silicone Sealant for significant joint movement or areas of frequent water immersion.
Do not apply or store below 5°C.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easier cleanup.
When first applying, extrude a small amount onto scrap material to ensure smooth, continuous flow of gap filler.
If wiping off excess with a wet finger, wet it with water (not saliva) to avoid bacteria that can promote mould growth.
Allow surfaces to skin before painting, approximately 30 minutes. Protect from rain until the surface is firmly skinned.
Some water-based undercoats and flat paints may crack when drying. To reduce this, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting.
Keep a pack of Selleys Sugar Soap Wipes handy for easy cleanup.
Clean Up
Water-based, so clean up with water.
Uncured product may be removed with water.
Cured product can be removed by sanding and scraping.
Size
450g Cartridge
Colours
Black
Brilliant White
Brown
Cedar
Charcoal
Coffee
Cream
Ivory
Light Grey
Technology
Water-Based
Use
Interior & Exterior
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Exterior & Weatherboard is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
Has good resistance to weathering
Contains a titanium compound for superior UV resistance.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application)..
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack.
Is formulated for long term resistance to cracking and crumbling.
Is water based, so can be cleaned up with water.
Will not stain building materials.
Where can this product be used?
Between exterior window and door frames
Fascia boards and eaves
Masonry Walls
Tiling
Timber & synthetic weatherboards
Brickwork
Fences
Where shrinkage or movement has caused rigid fillers to crack
Gaps with a maximum width of 25mm & depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Fibre cement sheeting, plasterboard
Masonry
Ceramic Tiles
Glass
Aluminium & other metals
Many other building surfaces
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Exterior is a specially formulated flexible gap filler, with superior weather, UV and mould resistance to protect against harsh external elements such as rain, wind and UV rays. It can be painted over with both water and oil based paints, so you can give your house the professional finish it deserves. Also available in easy tube format.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 500% elongation/stretch and up to +/- 25% joint movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
Has good resistance to weathering
Contains a titanium compound for superior UV resistance.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 30 minutes after application)..
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack.
Is formulated for long term resistance to cracking and crumbling.
Is water based, so can be cleaned up with water.
Will not stain building materials.
Where can this product be used?
Between exterior window and door frames
Fascia boards and eaves
Masonry Walls
Tiling
Timber & synthetic weatherboards
Brickwork
Fences
Where shrinkage or movement has caused rigid fillers to crack
Gaps with a maximum width of 25mm & depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Fibre cement sheeting, plasterboard
Masonry
Ceramic Tiles
Glass
Aluminium & other metals
Many other building surfaces
How To Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap.
Smooth with a wet spatula, ensuring sufficient product remains in joint.
Clean up with a damp cloth immediately.
Allow to skin (about 30 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Protect from water until firmly skinned. Allow for longer skin and cure times in damp conditions.
Limitations:
For new weatherboard, check weatherboard manufacturers instructions before using this product
Note that in very harsh conditions, joints between boards may expand beyond products movement capability. In such cases re-apply product and paint over.
Not suitable for areas of continuous water immersion eg ponds
Not suitable for application at below 5°C
Protect from rain until the product has firmly skinned, and allow longer skin and cure times in damp conditions.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats and flat paints may crack on drying. To reduce this effect, allow the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
For maximum durability on bare exterior surfaces, apply a coat of acrylic paint and allow to dry, before applying this gap sealant. Always paint over with a quality exterior paint.
To ensure you get a professional finish ensure you paint with a good quality paint and paint brush. Painting with a good brush ensures the finish and durability of the paint is increased. We recommend a 50mm Edger Brush, as the cut angle of the bristles takes the work out of applying paint.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Fast Dry has been designed to be painted over in just 20 minutes so that you can finish the job sooner! No More Gaps Fast Dry also provides superior crack resistance with high flexibility and low shrinkage.
Features
Paint over in 20 minutes*
Superior crack resistance
Superior adhesion to a broad range of surfaces, resulting in a lasting finish
A smooth flawless finish and minimal shrinkage
Can be cleaned up easily and quickly with water
Will not stain building materials
Can be used indoors and outdoors
*Allow longer drying times before painting with flat or ceiling paints or in cooler weather.
Where can this product be used?
Architraves
Skirting boards
Cornices
Window and door frames
Wall joints
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Painted surfaces
Many other building materials
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into caulking gun such as Selleys Light Speed Caulking gun.
Apply with caulking gun, forcing product into gap.
For a smooth finish, smooth with a finger dipped in water. For a professional finish use a paint scraper such as a 50mm Soft Grip Scraper.
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow to skin (about 20 minutes) before painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Limitations:
For gaps between tongue and groove boards and weatherboards use No More Gaps® Exterior & Weatherboard.
Where movement is excessive or for areas where contact with water is frequent, use the appropriate Selleys® Silicone Sealant.
Handy Tips
To avoid paint cracking, apply at temperatures above 10°C and do not apply paint too thick.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler, and a perfect finish.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to skin prior to painting, which is approximately 20 minutes.
Protect from rain until firmly skinned.
Allow for longer skin and cure times in damp conditions.
Some water based under coats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
For exterior applications protect from rain until firmly skinned.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint.
Features
Available in a great colour range, so no need to paint.
Paintable if required.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage
Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application).
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack
Is formulated for long term resistance to cracking and crumbling.
Is water-based, so can be cleaned up with water.
Will not stain building materials.
Has good resistance to weathering.
Mould and mildew resistance.
Where can this product be used?
Between window and door frames and the wall.
Along skirting boards.
Around cornices.
Between benchtops and tiles which are not exposed to water.
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm.
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Bare or painted surfaces
Colorbond
Many other building materials
How To Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and apply, forcing product into gap
Smooth with a wet finger or spatula
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Avoid water contact until fully cured- 72 hours or longer in cold weather.
Limitations:
Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps.
Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant.
Do not apply or store below 5°C.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
Features
Superior formulation+ that stops mould growth*
Fast skinning formulation which means you can use your shower in 1 hour
Provides a durable waterproof seal
Resists lifting
Where can this product be used?
Suitable for use in humid and damp environments such as
Kitchens
Bathrooms
Laundries
Showers
Basins
tiles
Worktops
Baths & spas
Plumbing fixtures
What materials is this product suitable for?
Ceramic
Glazed & porcelain fixtures
Aluminium
Plastic laminates
Some rubbers
Glass
Stainless Steel
How to Use
Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould
Thoroughly clean surface where sealant will be applied with turps and dry completely
Cut nozzle at 45°angle, cut cartridge tip and fit nozzle
Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint
Tool with a spatula dipped in detergent water within 5-10 minutes of application
Clean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area
#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)
*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth
Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
Tips
For neater joints, mask sides before applying the sealant and remove the tape before sealant skins
Not paintable. Complete painting 7 days before applying the sealant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
Features
Superior formulation+ that stops mould growth*
Fast skinning formulation which means you can use your shower in 1 hour
Provides a durable waterproof seal
Resists lifting
Where can this product be used?
Suitable for use in humid and damp environments such as
Kitchens
Bathrooms
Laundries
Showers
Basins
tiles
Worktops
Baths & spas
Plumbing fixtures
What materials is this product suitable for?
Ceramic
Glazed & porcelain fixtures
Aluminium
Plastic laminates
Some rubbers
Glass
Stainless Steel
How to Use
Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould
Thoroughly clean surface where sealant will be applied with turps and dry completely
Cut nozzle at 45°angle, cut cartridge tip and fit nozzle
Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint
Tool with a spatula dipped in detergent water within 5-10 minutes of application
Clean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area
#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)
*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth
Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
Tips
For neater joints, mask sides before applying the sealant and remove the tape before sealant skins
Not paintable. Complete painting 7 days before applying the sealant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Paint Over Sealant is a permanently paintable sealant.
Features
Paintable
Smooth flawless finish.
Easy to use and can be used on damp surfaces.
Superior adhesion to most building materials.
Low odour so can be used in any environment without discomfort.
Weather resistant by forming a durable seal which remains flexible, not drying or cracking
Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch.
Temperature resistance – approximately -40°C +93°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
May be discoloured by contact with alloys containing brass, copper or zinc.
Do not allow unused product to freeze.
Where can this product be used?
10879.Window frames that need painting
102879.Capstones Masonry walls that need painting
Perfect for use on or around:
Bricks and concrete
Windows frames
Tiled and wooden fixtures
Areas where a sealant is needed and where you want to paint it
Not suitable for use in below waterline applications.
Not suitable for use on oily woods such as cypress, teak or cedar.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Glass
Aluminium
Fibre Cement
Painted Surfaces
Ceramics
Masonry
Most metals
Most plastics
Wood
How to use this product
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant.
Remove the tape before the sealant skins.
For a better finish use a spatula dipped in detergent and water to tool off the sealant.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
To improve the paint finish, wipe the sealant with detergent solution immediately before painting.
Avoid smearing sealant on the surrounding surfaces as this may effects its paintability.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Porcelain Fix is a high strength two part white epoxy adhesive filler in a handy dual syringe. Specifically designed to fill and repair cracks, chips and breakages in porcelain, enamel and crockery.
Features
-High Strength – 2 part epoxy mix ensures high strength
-Achieves maximum bond within 8 hours
-Generous working time – Up to 10 minutes at 20°C
-Can be sanded
-Dries white and can be painted over
-Heat resistant to 93°C
-Can be used as gap filler – i.e. if join of breakage does not match up perfectly
-Can be tinted
Where can this product be used?
-For bonding & filling: China, pottery, porcelain, ceramics, Earthenware
-Repair a chipped sink
-Repairing broken crockery – plates, cups, bowls etc
-Fix a chip in your porcelain or enamel basin or bath
-Repairing chips or replacing a broken section of your toilet
-Should not be used on objects subject to high temperatures such as ovens and dishwashers.
What materials is this product suitable for?
China
Pottery
Porcelain
Ceramics
Earthenware
Bathroom fittings
How to use this product
-Surfaces joined should be clean and dry.
-Remove cap and pierce seal in each nozzle with the spatula/pin provided.
-The dual syringe will dispense equal portions of Part ‘A’ and Part ‘B’. Mix thoroughly.
-Apply to one surface, then bring together and hold using tape, weights etc.
-Once cured this product is extremely difficult to remove. Any material squeezed out of joints or split is best removed before it sets using Solvent Acetone or Methyl Ethyl Ketone solvent.
-Wipe nozzles after use. Pull the plunger back slightly and replace cap firmly over nozzles.
Handy tips
-For filling only, can be tinted with iron oxide or other dry pigments which must be mixed in very thoroughly.
-Softens at high temperatures, but strength returns when cooled.
-Wear protective gloves and eye protection when mixing or using.
-Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
-Clean up excess material with Acetone immediately. Once set the product cannot be removed easily
-To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
-To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Safety tips
-Avoid contact with skin and eyes and avoid breathing its vapours.
-Wear protective gloves when mixing and using.
-If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 13 11 26 or New Zealand 0800 764 766.
-If swallowed DO NOT induce vomiting. Give a glass of water and seek medical advice.
-If skin contact occurs, remove contaminated clothing and wash skin thoroughly. If in eyes, hold eyes open, flood with water for at least 15 minutes and see a doctor.
-For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Store syringe in an upright position with nozzles uppermost, in a cool dry location, away from direct sunlight.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS.
Features
Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS
Shock resistant, giving you a longer-lasting fix
Fast setting in 30 seconds
Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper
*Does not work on PTFE (Teflon)
Where can this product be used?
To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control
What materials is this product suitable for?
ALL plastics* including polyethylene, polypropylene and ABS
Metals
Timber
China
Rubber
Leather
Paper
How to Use
Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface.
Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise.
Remove cap and apply a small amount of glue to one surface only.
Limitations:
Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam.
Product only works on some rubbers and will not work on PTFE. May cause leather to harden or discolour, test on an inconspicuous area first.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue.
Features
Bonds a variety of surfaces
Extremely fast setting
Dries Clear for clean, neat results
Water resistant
No clamping necessary
No mixing required
Maximum strength achieved in 12 hours
Only takes 45 seconds to achieve an initial bond
Self-piercing, clog-free cap
Forms a strong, flexible bond
Impact Resistant – 4 times greater impact resistance than normal supa glues
Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues
Heat Resistant to 120°C permanently, 150°C intermittently
Comes with a nozzle for easy, accurate application
Appearance
Clear thick liquid dries to a colourless film.
Where can this product be used?
Ideal for small repair jobs or when immediate results are required
Fixing a broken door knocker
Refixing wooden or metal door handles
Repairing crockery safe to put in the dishwasher
Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
Will not permanently bond glass or other materials containing alkaline elements
Not recommended for highly porous surfaces
What materials is this product suitable for?
Bonds a variety of porous and non-porous surfaces
Metals
Wood
China
Rubber
Leather (test first as leather may become hardened or discoloured)
Some plastics
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips.
Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise.
Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
Allow 12 hours for sufficient bond strength for practical use.
Handy tips
Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue.
Excellent when used with other adhesives, as the temporary tack.
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting.
After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water.
Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin.
While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Supa glues cure more slowly when large amounts are used. For faster cure use sparingly.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin.
Do not use near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site.
Storage and re-use
After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly.
Ensure cap is replaced and store in a cool dry place.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula
Superior flexibility with +/- 25% movement capability
Temperature resistance: approximately -60°C to +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25-year guarantee* against crumbling, cracking, and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm²/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass, and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics, including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula.
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm2/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof & Gutter Ezi Press is easy to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and excellent UV and weather resistance. Ideal for roofing, guttering and flashing outside the home.
Best for: Aluminium, Sheet Metal, Copper, Brass, Galvanised Metals, Rigid PVC and most plastics including polystyrene, Terracotta, Concrete, Glazed tiles, BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
UV and weather resistant
Precision application for the best finish
Where can this product be used?
Metal and tile roofing
Colorbond roofs and fences
Guttering and flashings
Skylights
Around air conditioning units
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Use in a well ventilated are. Avoid contact with skin and eyes.
Throughly clean and dry surface from oil, dirt and grease with mineral turps.
Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Do not use in below ground applications.
• Sealant is not paintable. Complete painting 7d prior to applying sealant.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs.
Features
Easy to use
Strong
Flexible Bond
Weather resistant
Impact resistant
Appearance
Dries yellowish/beige
Where can this product be used?
Sole
Tongue
Strap
Inner sole
Attach beads, jewels, decorative items
Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles.
What materials is this product suitable for?
Leather
Canvas
Fabric
Rubber
Cork
Most Plastics
EVA foam (e.g Desert boots sole)
How to use this product
Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal.
For larger area repairs such as shoe soles, we recommend you use the contact bond method:
For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes).
Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications.
For smaller areas, either use the contact method as above, or join with a wet bond:
Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry.
Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s.
Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries.
Handy tips
A piece of plastic from a takeaway container makes a good applicator for shoe soles.
Bulldog clips are handy to use for clamping straps and other small areas.
Pack includes a removable nozzle for easy application.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys SolarFlex
Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical.
Features
Superior weather protection
Long-lasting flexibility
No primer required before painting
Watertight seal with a 10-year guarantee*
Adhesion to wet or damp surfaces
Non-bubbling
Better curing and extrudability (>5°C) with no slump
Paintable with water-based paints after product skins in 60 to 90 minutes
Low VOC**
Where can this product be used?
Skylights
Walls
Patios
Floors
Fencing
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic tiles
Fibreglass
Most plastics*
*Not suitable on polyethylene, polypropylene, or Teflon.
Application Instructions
Ensure substrates are clean and free of oil, grease, or loose particles.
Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun.
Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint.
For neat joints, use masking tape on both sides of the joint and remove it before skinning.
Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information.
Limitations
Not suitable on polyethylene, polypropylene, or Teflon.
Cure excess product before disposal.
Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sole Grip is an easy-to-apply compound to repair and protect most shoe soles. Use it to coat the soles of shoes and protect from general wear and tear, extending the life of your shoes.
Features:
Easy to use
Long wearing
May be applied to both new and old shoe soles, as a repair or non-slip surface
Appearance
Dark brown tacky paste.
Where can this product be used?
Apply to new shoes to extend their sole life
Building up worn soles of shoes to extend their life
Creating an anti-slip surface on smooth soles of shoes
Creating an anti-slip surface on the bottom of furniture legs and castor holders
Creating an anti-slip base on fabric items such as dollies or placemats
Sole Fix is not an adhesive
May not adhere to some plastic/rubber soles
Will not bridge gaps where no backing exists
What materials is this product suitable for?
Leather
Rubber
Synthetic
Plastic
How to use this product
Roughen soles with the scraper provided.
Clean the surface with Selleys Solvent Acetone. Do not use Turpentine or Kerosene. (Note: Slow drying solvents such as Mineral Turps may interfere with adhesion).
Squeeze sufficient material for a thin layer about 1.5mm thick. Spread evenly over sole
Leave for 30 minutes before further applications. If required, apply 2 or 3 layers on average soles. On worn soles apply to suit.
Leave for 24 hours before wearing. Edges may be sandpapered or cut back and trimmed with a knife.
Handy tips
For best results, new shoes should be worn for several days before applying SoleGrip
Clean up excess with Mineral Turpentine prior to cure
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Avoid skin contact and avoid breathing vapours.
If eye contact occurs, flush eyes with water for 15 minutes. Obtain medical attention. If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If swallowed, DO NOT induce vomiting. Give a glass of water and seek medical advice. Intentional misuse by deliberately inhaling vapours of this product can be harmful or fatal.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler.
Features
Suitable for interior and exterior applications
Good adhesions to most surfaces
Water and weather resistant
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs
What materials is this product suitable for?
Mortar
Masonry
Concrete
Wood
Stone
Primed metal surfaces
Brick
Plaster
Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next.
Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications).
Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints.
Limitations:
Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps.
Avoid using below 5°C or in wet conditions.
Painting with oil-based paints is not recommended until 24 hours after the filler has been applied.
Water-based paints may be used immediately after the filler has set.
If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application.
Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Wallboard
Wood
Masonry
Plaster
Primed nail heads
Plasterboard
Colours White
Technology Water Based
Use Interior
Exterior (when painted)
How To Use
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications).
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Handy Tips
Painting with oil-based paints is not recommended until 24 hours after filler has been applied.
Water based paints may be used immediately after filler has set.
If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping or sanding.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application.
Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Wallboard
Wood
Masonry
Plaster
Primed nail heads
Plasterboard
Colours White
Technology Water Based
Use Interior
Exterior (when painted)
How To Use
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications).
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Handy Tips
Painting with oil-based paints is not recommended until 24 hours after filler has been applied.
Water based paints may be used immediately after filler has set.
If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping or sanding.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Storm Waterproof Tape is a quick and easy way to seal and patch most objects*. It can be applied in the rain to stop leaks in an instant. Storm Waterproof Tape stops water leaks for 48 hours, making it ideal for emergency fixes until permanent repairs can be made.
Features
Waterproof & airtight seal* – Wet or Dry
Stops active water leaks for up to 48 hours*
Sticks to wet surfaces*
Removable
Suitable for interior and exterior
Suitable for fresh, salt & chlorinated water
Easy-to-use, DIY optimised format
Where can this product be used?
Can be used on gutters & flashing, down pipes, caravans, tents & tarps, rubber/plastic/vinyl pool liners, PVC piping, inflatable pool toys, small boats & kayaks air mattresses, umbrellas and more!
Suitable for Aluminium, Galvanised Steel, Colorbond® Steel, Copper, Brass, Fibreglass, some rubbers and plastics*
Ensure surface is free of dirt, grease and oil
Cut tape or patch to desired size. Ensure there is at least 2-3cm of tape extending beyond each edge of the hole
Remove backing paper, position carefully and press down firmly
Once in position, rub firmly to ensure no air or water bubbles are left under the tape, and ensure good contact between the tape and substrate
Leave tape until permanent repairs can be made
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](//gluesaustralia.com.au/cdn/shop/files/81ee53b7eade4c22a1268e1a28879d4e.jpg?v=1757753123&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](//gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](//gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Off White]](//gluesaustralia.com.au/cdn/shop/files/9300697130334_5a88883c-9e8a-4c25-80f6-535ba26ac80d.png?v=1754711844&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](//gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](//gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](//gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](//gluesaustralia.com.au/cdn/shop/files/8a8dbfbe2151431e9a3365cd49a9be75.jpg?v=1757753104&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](//gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Filler Sealant Fast Dry [White]](//gluesaustralia.com.au/cdn/shop/files/da7575e6045648c8aee7c9769b69a8cc.jpg?v=1757753086&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](//gluesaustralia.com.au/cdn/shop/files/87cc1e989ee946138f896f38cf05e9d4.jpg?v=1757753073&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](//gluesaustralia.com.au/cdn/shop/files/62810ec4c8d842009839ace74d1cac64.png?v=1757753067&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](//gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](//gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](//gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](//gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](//gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent]](//gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
![Selleys No Mould Silicone Selant 100ml [White]](//gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](//gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](//gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/81ee53b7eade4c22a1268e1a28879d4e.jpg?v=1757753123&width=645)
![Selleys No More Gaps Bricks Mortar [Charcoal]](http://gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys No More Gaps Bricks Mortar [Off White]](http://gluesaustralia.com.au/cdn/shop/files/9300697130334_5a88883c-9e8a-4c25-80f6-535ba26ac80d.png?v=1754711844&width=645)
![Selleys No More Gaps Bricks Mortar [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/9300697130297_4ba0669c-67f5-40d4-9f47-db82307f921f.png?v=1754711842&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](http://gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
![Selleys No More Gaps Exterior & Weatherboard 430g [White]](http://gluesaustralia.com.au/cdn/shop/files/8a8dbfbe2151431e9a3365cd49a9be75.jpg?v=1757753104&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Filler Sealant Fast Dry [White]](http://gluesaustralia.com.au/cdn/shop/files/da7575e6045648c8aee7c9769b69a8cc.jpg?v=1757753086&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 150g [White]](http://gluesaustralia.com.au/cdn/shop/files/87cc1e989ee946138f896f38cf05e9d4.jpg?v=1757753073&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler 475g [White]](http://gluesaustralia.com.au/cdn/shop/files/62810ec4c8d842009839ace74d1cac64.png?v=1757753067&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
![Selleys No Mould Silicone Sealant Waterproof [White]](http://gluesaustralia.com.au/cdn/shop/files/121994701b5c42c1bd5e5c839bcfcd4e.jpg?v=1757753039&width=645)
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
