Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Marathon is the best carpet shampoo for commercial and domestic extraction machines. It removes dirt, grime, food residue from carpets without leaving any harsh detergents or chemicals behind. It's perfect for your steamy carpet extraction machine to scrub up tough stains on all carpets with just one application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Marathon Sugar Soap for Walls and Floors cleans dirt, grease, and grime from all types of flooring. Remove soap scum from showers with ease on mirror shower doors. The multi-use formula means one product can do more than just one job!
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied.
Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house.
Mould Defence can be added to a wide range of products including paint (water based and solvent), timber
oils/stains, textured coatings, grout, mortar and adhesive.
Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied.
Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house.
Mould Defence can be added to a wide range of products including paint (water based and solvent), timber
oils/stains, textured coatings, grout, mortar and adhesive.
Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied.
Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house.
Mould Defence can be added to a wide range of products including paint (water based and solvent), timber
oils/stains, textured coatings, grout, mortar and adhesive.
Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied.
Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house.
Mould Defence can be added to a wide range of products including paint (water based and solvent), timber
oils/stains, textured coatings, grout, mortar and adhesive.
Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied.
Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house.
Mould Defence can be added to a wide range of products including paint (water based and solvent), timber
oils/stains, textured coatings, grout, mortar and adhesive.
Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything
Features and Benefits:
Environmentally friendly
Non-toxic
Dries quickly – dries clear
Non-flammable
High water resistance
Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle.
Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass.
It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces.
Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything
Features and Benefits:
Environmentally friendly
Non-toxic
Dries quickly – dries clear
Non-flammable
High water resistance
Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle.
Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass.
It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces.
Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything
Features and Benefits:
Environmentally friendly
Non-toxic
Dries quickly – dries clear
Non-flammable
High water resistance
Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle.
Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass.
It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces.
Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything
Features and Benefits:
Environmentally friendly
Non-toxic
Dries quickly – dries clear
Non-flammable
High water resistance
Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle.
Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass.
It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces.
Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything
Features and Benefits:
Environmentally friendly
Non-toxic
Dries quickly – dries clear
Non-flammable
High water resistance
Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle.
Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass.
It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces.
Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Water-based interior wood filler suitable for all timber types and timber by-products. Once set, the wood filler can be sanded, screwed, and nailed. The wood filler is suitable for filling cracks, holes, end grain, and edges.
For exterior use, protect with a suitable exterior grade finish (e.g. paint or stain)
Features & Benefits
Environmentally friendly
Dries quickly
Water clean up
Easy to use
Long shelf-life; if filler hardens just add drops of water & mix
Multi-purpose, 4 in 1 uses – fills nails holes, takes stain or paint easily, repairs gouges & chips and crack & edge filler
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items.
Also suitable for sealing and polishing slate, terracotta and stucco
Coverage: Up to 40 m2
Number of Coats: 2
Recoat: 24hrs
Sheen Level: Pale Satin
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items.
Also suitable for sealing and polishing slate, terracotta and stucco
Coverage: Up to 40 m2
Apply with: Lint free cloth
Coats: 2
Recoat: 24 Hours
Sheel Level: Pale Satin
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polishes internal furniture & joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items.
Also suitable for sealing and polishing slate, terracotta and stucco
Coverage: Up to 40 m2
Apply with: Lint free cloth
Coats: 2
Recoat: 24 Hours
Sheel Level: Pale Satin
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polishes internal furniture & joinery that has been previously waxed or oiled
Suitable for Timber, concrete, slate, terracotta and stucco
All-natural ingredients
Apply with a lint-free cloth
Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items.
Uses: Also suitable for sealing and polishing slate, terracotta and stucco
Coverage: Up to 40m²
Apply with: Lint-free cloth
Number of coats: 2
Sheen level: Pale Satin
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Polishes internal furniture & joinery that has been previously waxed or oiled
Suitable for Timber, concrete, slate, terracotta and stucco
All-natural ingredients
Apply with a lint-free cloth
Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items.
Uses: Also suitable for sealing and polishing slate, terracotta and stucco
Coverage: Up to 40m²
Apply with: Lint-free cloth
Number of coats: 2
Sheen level: Pale Satin
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications.
Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried.
Environmentally friendly
Dries white
Dries fast
Very high weather resistance
Unique properties make this product easy to shape and sand
Ideal for schools and craft classes or just having fun!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications.
Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried.
Environmentally friendly
Dries white
Dries fast
Very high weather resistance
Unique properties make this product easy to shape and sand
Ideal for schools and craft classes or just having fun!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications.
Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried.
Environmentally friendly
Dries white
Dries fast
Very high weather resistance
Unique properties make this product easy to shape and sand
Ideal for schools and craft classes or just having fun!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Manufactured from special fibred paper with added tensile strength. Buffed on both sides to ensure optimum bonding and holding power. Perforated for ease of use and better adhesion.
Easy to use
DIY with professional results
Strong bonding and holding power
Self adhesive
Quick results
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications.
Environmentally friendly
Non-toxic
Tough & flexible
Easy to use
Weather-resistant
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-part gap filler and binder for builders and tradesmen that is a safe alternative to the toxic solvent and styrene-based fillers and bogs on the market.
Environmentally friendly and non-hazardous for safe handling and easy transport
Easy to mix, spread on rough and smooth substrates immediately
Rapidly sets in 15 mins (faster in warm weather) with minimal shrinkage
Curing time approximately 60 minutes • Long shelf life when firmly sealed after each use
Once cured it may be chiselled, filed, sawn, planed and sanded into shape
Can also be nailed, drilled, screwed, glued and painted
Highly recommended for waterproofing as gap filler for bathroom renovations and other wet area applications where tiling or painting is required
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Protite Mould Defender Anti-Fungal Paint Additive 75 mL is a reliable liquid paint additive that helps inhibit mould growth in humid areas chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 75 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Protite Mould for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Protite Mould Defender Anti-Fungal Paint Additive 75 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Bathrooms and laundries
Kitchens and food prep zones
Rental refresh and maintenance work
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Walls and ceilings coated with water based paint
Suitable primers as per paint maker guidance
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of Work to normal paint tray timelines. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Mix thoroughly into your chosen paint and apply as directed by that paint. Dry and recoat times follow the paint system.
Temperature and environmental performance
Use within the temperature window recommended for the host paint. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean rollers and brushes according to the paint manufacturer's advice. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store upright with cap tight. Do not allow to freeze or overheat. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications.
Environmentally friendly
Non-toxic
Tough & flexible
Easy to use
Weather-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Single Shot, no mess just throw away
Self piercing tube
Bonds in 10 seconds
Where can this product be used?
Ideal for small repair jobs or when immediate results are required
For interior projects and repairs
Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
Will not permanently bond glass or materials containing alkaline elements
Has no gap filling properties, therefore, surfaces need to be a close fit
Not recommended for highly porous surfaces
What materials is this product suitable for?
Metals
China
Rubber
Leather
Some plastics
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application.
Features
Easy, controlled application
Non-drip glue saver nozzle, reduces waste and mess.
Long fine nozzle for precise application
Bonds a variety of surfaces
Extremely fast setting
Dries Clear for clean, neat results
Water resistant
No clamping necessary
No mixing required
Maximum strength achieved in 12 hours
Only takes 45 seconds to achieve initial bond
Non-clog cap
Forms a rigid bond
Upright self-standing bottle
Comfortable to hold
Where can this product be used?
Ideal for small repair jobs or when immediate results are required.
Water resistant not water proof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene.
Leather may become hardened or discoloured For interior use only
Not suitable for repairing items that are in direct contact with hot liquids
Will not permanently bond glass or materials containing alkaline elements.
Has no gap filling properties therefore surfaces need to be a close fit
Not recommended for highly porous surfaces
What materials is this product suitable for?
Bonds a variety of porous and non-porous surfaces
Metals
China
Rubber
Leather
Some plastics
Wood
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust.
Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise.
Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded.
Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours.
Handy tips
Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated.
Clean the affected area with acetone to remove residue.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Excellent when used with other adhesives, as the temporary tack
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin.
While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Super glues cure more slowly when large amounts are used. For faster cure use sparingly.
Safety tips
Avoid contact with the skin and eyes. Avoid breathing vapour.
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
Storage and re-use
After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle.
To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method.
Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture.
Store Upright.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fast setting liquid supa glue in a self-standing bottle with brush applicator. Dries clear.
Features
Bonds a variety of surfaces
Extremely fast setting
Dries Clear for clean, neat results
Water resistant
No clamping necessary
No mixing required
Maximum strength achieved in 12 hours
Only takes 45 seconds to achieve an initial bond
Ideal for craft and collage applications
Forms a rigid bond
Easy to spread over wider areas from a stable self-standing bottle
Where can this product be used?
Useful for jobs with a wide surface area in both a repair and create capacity.
Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene.
Leather may become hardened or discoloured
For interior use only
Not suitable for repairing items that are in direct contact with hot liquids
Will not permanently bond glass or materials containing alkaline elements.
Has no gap filling properties, therefore, surfaces need to be a close fit
Not recommended for highly porous surfaces
What materials is this product suitable for?
Bonds a variety of porous and non-porous surfaces
Metals
China
Rubber
Leather
Some plastics
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust.
Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
The product grabs within 10-60 seconds, depending on environmental conditions and substrates to be bonded.
Allow 30 minutes for sufficient bond strength for practical use.
Ensure cap is replaced immediately after applying adhesive, as this prolongs the life of brush applicator.
Handy tips
Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Excellent when used with other adhesives, as the temporary tack
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin.
While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Super glues cure more slowly when large amounts are used. For faster cure use sparingly.
To remove excess from substrates, it is recommended that the material is soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Quick Fix Supa glue bonds on contact, if fingers should stick together, apply a solvent such as acetone to affected areas and wash off with water.
If no solvent is available wash area with warm soapy water and work fingers apart.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non-toxic when set
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin.
Storage and re-use
After use, tap bottle lightly on a flat surface to clear excess product from the nozzle.
Ensure cap is replaced and store in a cool dry place.
Store Upright.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fast setting ethyl cyanoacrylate (suclog-freebased adhesive with a non-drip gel consistency which dries clear.
Features:
-Bonds a variety of surfaces
-Extremely fast setting
-Dries Clear for clean, neat results
-Water resistant
-No clamping necessary
-No mixing required
-Maximum strength achieved in 12 hours
-Only takes 45 seconds to achieve an initial bond
-Self-piercing, clog-free cap
-Forms a rigid bond
-The non-drip gel consistency is ideal for vertical jobs
-Can be used for gap filling due to a gel consistency
Where can this product be used?
-The non-drip gel consistency makes it particularly useful on vertical surfaces
-Ideal for small repair jobs or when immediate results are required
-For interior projects and repairs.
-Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet
-Not suitable for bonding plastics such as Polypropylene and Polyethylene
-Leather may become hardened or discoloured
-Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
-Will not permanently bond glass or materials containing alkaline elements
What materials is this product suitable for?
-Bonds a variety of porous and non-porous surfaces
-Metals
-Wood
-China
-Rubber
-Leather (test first as some leather may become hardened or discoloured)
-Some plastics
How to use this product
-Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible.
-Surfaces to be bonded should be clean, dry and free of dust.
-Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise.
-Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
-The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded.
-Allow 30 minutes for sufficient bond strength for practical use.
Handy tips
-Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue.
-Use Quick Fix Gel on vertical surfaces.
-Excellent when used with other adhesives, as the temporary tack.
-For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting.
-After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover.
-For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
-In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
-Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would.
-Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin.
-Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions.
-Super glues cure more slowly when large amounts are used. For faster cure use sparingly.
-While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use.
Safety tips
-Avoid contact with the skin and eyes.
-Avoid breathing vapour.
-Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin.
-Do not use near eyes or open wounds.
-In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
-Non-toxic when set
-For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site.
Storage and re-use
-After use, wipe excess product from the nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly.
-Ensure cap is replaced and store in a cool dry place.
-For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fast setting ethyl cyanoacrylate (supa glue) based adhesive with a non-drip gel consistency which dries clear.
Features
-Bonds a variety of surfaces
-Extremely fast setting
-Dries Clear for clean, neat results
-Water resistant
-No clamping necessary
-No mixing required
-Maximum strength achieved in 12 hours
-Only takes 45 seconds to achieve an initial bond
-Self-piercing, clog-free cap
-Forms a rigid bond
-The non-drip gel consistency is ideal for vertical jobs
-Can be used for gap filling due to the gel consistency
Where can this product be used?
-The non-drip gel consistency makes it particularly useful on vertical surfaces
-Ideal for small repair jobs or when immediate results are required
-For interior projects and repairs.
-Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet
-Not suitable for bonding plastics such as Polypropylene and Polyethylene
-Leather may become hardened or discoloured
-Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
-Will not permanently bond glass or materials containing alkaline elements
What materials is this product suitable for?
-Bonds a variety of porous and non-porous surfaces
-Metals
-Wood
-China
-Rubber
-Leather (test first as some leather may become hardened or discoloured)
-Some plastics
How to use this product
-Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible.
-Surfaces to be bonded should be clean, dry and free of dust.
-Pierce seal at end of tube by attaching nozzle and cap and turning clockwise.
-Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
-The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded.
-Allow 30 minutes for sufficient bond strength for practical use.
Handy tips
-Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue.
-Use Quick Fix Gel on vertical surfaces.
-Excellent when used with other adhesives, as the temporary tack.
-For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting.
-After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover.
-For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
-In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
-Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would.
-Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from skin.
-Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions.
-Super glues cure more slowly when large amounts are used. For faster cure use sparingly.
-While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
-For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
-Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
-Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use.
Safety tips
-Avoid contact with the skin and eyes.
-Avoid breathing vapour.
-Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin.
-Do not use near eyes or open wounds.
-In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
-Non toxic when set
-For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site.
Storage and re-use
After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly.
Ensure cap is replaced and store in a cool dry place.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quick Fix No Mess Stand Up Tube is the Supa Smart Supa Glue. The tube controls the flow of adhesive for precise applications and will retract partly dispensed glue from the nozzle so it will never clog up and dry out between uses. The stand up feature also means you don’t end up with messy drops of glue on the benchtop!
Features
-Free standing tube prevents leaks and retracts party dispensed glue
-Prevents squeeze out and provides maximum application control
-Bonds a variety of surfaces
-Extremely fast setting, sets in 10 seconds
-Maximum strength achieved in 12 hours
-Dries clear for clean, neat results
-Water resistant
-No clamping necessary
-Self piercing, clog free cap
-Forms a rigid bond
Where can this product be used?
Ideal for small repair jobs or when immediate results are required
For interior projects and repairs
Water resistant not water proof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
Will not permanently bond glass or materials containing alkaline elements
Has no gap filling properties therefore surfaces need to be a close fit
Not recommended for highly porous surfaces
What materials is this product suitable for?
Metals
China
Rubber
Leather
Some plastics
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust.
Pierce seal at end of tube by attaching nozzle and cap and turning clockwise.
Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
The product grabs within 2-30 seconds, depending on environmental conditions and materials to be bonded.
Allow 30 minutes for sufficient bond strength for practical use.
Handy tips
Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone (most nail polish removers) to remove residue.
Excellent when used with other adhesives, as the temporary tack.
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting.
After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water.
Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from skin.
While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Supa glues cure more slowly when large amounts are used. For faster cure use sparingly.
To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Hand Kleen Wipes nearby for a quick and effective cleanup.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin.
Do not use near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site.
Storage and re-use
After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly.
Ensure cap is replaced and store in a cool dry place.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
An all purpose, high strength household glue that unlike standard superglues is extremely ‘infinitely’ more flexible. It can repair and bond a variety of surfaces and withstand the most extreme/rough conditions whilst providing the ultimate bond.
Features
Strong Bond
Ultra Flexible – infinitely more flexible*
Extreme Resistance to: Shocks & Vibration, Torsion & Movement, Water and Extreme Temperatures
Dishwasher Safe
Gap Filling (works on uneven surfaces)
Paintable
Adjustable for 1min
Non-Drip (great for vertical surfaces)
Interior/Exterior
Easy to use
Heat resistant -15°C to +120°C
Solvent free, no shrinkage
Colour
Dries translucent
What materials is this product suitable for?
Metal
Wood
Glass
Rubber
China
Leather
Ceramics
Masonry
Fibreglass
Vinyl
Cardboard
Fabric
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place
Safety Tips
On contact, uncured adhesive can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice.
Avoid contact with skim. If contact occurs, wipe off and wash with detergent. Avoid breathing vapours.
Use in a well ventilated area
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quickset WATERCRETE
Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming
grating ledges to repairing the Owen Falls Dam in Uganda.
Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre.
Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes.
Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water.
BRIEF TECHNICAL SPECIFICATIONS
Initial set 5 minutes. Curing set 15-30 minutes.
Compressive strength of 2,000psi or greater in 24 hours
Maximum strength in 28 days
Non-toxic
Volume change: Expansion after 24 hours 0.1%
Contraction after 28 days 0.01%
Water absorption 1.7% after 14 days
Factory Production to BS 5750 Part II
BONDS TO:
CEMENT
TIMBER
MASONRY
FIBREGLASS
STEEL
INSTRUCTIONS FOR USE
Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quickset WATERCRETE
Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming
grating ledges to repairing the Owen Falls Dam in Uganda.
Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre.
Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes.
Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water.
BRIEF TECHNICAL SPECIFICATIONS
Initial set 5 minutes. Curing set 15-30 minutes.
Compressive strength of 2,000psi or greater in 24 hours
Maximum strength in 28 days
Non-toxic
Volume change: Expansion after 24 hours 0.1%
Contraction after 28 days 0.01%
Water absorption 1.7% after 14 days
Factory Production to BS 5750 Part II
BONDS TO:
CEMENT
TIMBER
MASONRY
FIBREGLASS
STEEL
INSTRUCTIONS FOR USE
Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Brush-Box]](//gluesaustralia.com.au/cdn/shop/files/9314261009223_76fac964-6223-45fd-bbba-c5872cc3ed41.png?v=1754723592&width=645)
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Cedar]](//gluesaustralia.com.au/cdn/shop/files/9314261009148.png?v=1754723592&width=645)
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Brush-Box]](http://gluesaustralia.com.au/cdn/shop/files/9314261009223_76fac964-6223-45fd-bbba-c5872cc3ed41.png?v=1754723592&width=645)
![Prep Multipurpose Quick Drying Wood Filler Putty Water Based 250g [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9314261009148.png?v=1754723592&width=645)
