In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant
Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck.
Why Choose Sikaflex®-291
Excellent adhesion to common marine substrates
Good ageing & weathering resistance for long service life
Elastic to absorb vibration and movement
Low odour and non-corrosive
Overpaintable and sandable after cure*
Available colours: White, Grey, Black
*Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area.
Typical Uses
Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications.
Suitable Substrates
Wood
Metals, metal primers and 2-component paint systems
Ceramic materials
Plastics such as GRP (fibreglass), etc.
Do Not Use On
Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate)
Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility.
Technical Data (Typical)
Property
Method / Note
Value
Chemical base
—
1-component polyurethane
Cure mechanism
—
Moisture-curing
Colour
CQP001-1
White, Grey, Black
Density (uncured)
—
~1.3 kg/L (colour-dependent)
Non-sag properties
—
Good
Application temperature
Ambient
5 – 40 °C (optimum 15 – 25 °C)
Skin time
CQP019-1 (A)
~60 minutes
Open time
CQP526-1 (A)
~45 minutes
Curing speed
CQP049-1
Depends on temperature & humidity (see TDS)
Shrinkage
CQP014-1
~5 %
Shore A hardness
CQP023-1 / ISO 48-4
~40
Tensile strength
CQP036-1 / ISO 527
~1.8 MPa
Elongation at break
CQP036-1 / ISO 527
~500 %
Tear resistance
CQP045-1 / ISO 34
~6 N/mm
Service temperature (continuous)
CQP513-1
−50 to +90 °C
Service temperature (short-term)
CQP513-1
+160 °C (4 h), +180 °C (1 h)
Shelf life
(B)
12 months (store < 25 °C)
CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C.
Application Guidance
Surface Preparation
Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates.
Application
Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity.
Optimum substrate and product temperature is 15 – 25 °C.
Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment.
Tooling & Finishing
Tool within the skin time.
Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability).
Cleaning & Removal
Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent.
Cured material: remove mechanically (e.g. knife, wire, abrasion).
Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting.
If the paint requires baking > 80 °C, allow the sealant to fully cure first.
Always conduct preliminary trials under manufacturing conditions.
Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area.
Compliance & Approvals
Meets requirements set out by the International Maritime Organization (IMO).
Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable.
FAQs
Can Sikaflex®-291 be overpainted?
Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area.
What is a “marine grade” sealant/adhesive?
Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline.
When and why should a primer be used?
Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing.
What does the Wheelmark indicate?
The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED).
Which substrates does Sikaflex®-291 bond to?
Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate).
How do I remove Sikaflex®-291?
Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material.
Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-291 Marine Adhesive Sealant Multifunctional, IMO-Compliant
Sikaflex®-291 is a non-sag, 1-component polyurethane sealant developed for the marine market. It cures on exposure to atmospheric moisture to form a durable, elastic seal. Engineered for demanding on-board environments, Sikaflex®-291 meets International Maritime Organization (IMO) requirements and is suitable for a wide range of sealing and light bonding tasks above and below deck.
Why Choose Sikaflex®-291
Excellent adhesion to common marine substrates
Good ageing & weathering resistance for long service life
Elastic to absorb vibration and movement
Low odour and non-corrosive
Overpaintable and sandable after cure*
Available colours: White, Grey, Black
*Always test paint compatibility. Paint elasticity is typically lower than sealant elasticity and can crack in the joint area.
Typical Uses
Multipurpose sealing and light bonding in marine construction, including elastic, vibration-resistant joints and interior sealing applications.
Suitable Substrates
Wood
Metals, metal primers and 2-component paint systems
Ceramic materials
Plastics such as GRP (fibreglass), etc.
Do Not Use On
Plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate)
Professional users only. Always test with actual substrates and site conditions to confirm adhesion and compatibility.
Technical Data (Typical)
Property
Method / Note
Value
Chemical base
—
1-component polyurethane
Cure mechanism
—
Moisture-curing
Colour
CQP001-1
White, Grey, Black
Density (uncured)
—
~1.3 kg/L (colour-dependent)
Non-sag properties
—
Good
Application temperature
Ambient
5 – 40 °C (optimum 15 – 25 °C)
Skin time
CQP019-1 (A)
~60 minutes
Open time
CQP526-1 (A)
~45 minutes
Curing speed
CQP049-1
Depends on temperature & humidity (see TDS)
Shrinkage
CQP014-1
~5 %
Shore A hardness
CQP023-1 / ISO 48-4
~40
Tensile strength
CQP036-1 / ISO 527
~1.8 MPa
Elongation at break
CQP036-1 / ISO 527
~500 %
Tear resistance
CQP045-1 / ISO 34
~6 N/mm
Service temperature (continuous)
CQP513-1
−50 to +90 °C
Service temperature (short-term)
CQP513-1
+160 °C (4 h), +180 °C (1 h)
Shelf life
(B)
12 months (store < 25 °C)
CQP = Corporate Quality Procedure. (A) 23 °C / 50 % r.h. (B) Storage below 25 °C.
Application Guidance
Surface Preparation
Substrates must be clean, dry, and free from grease, oil, and dust. Surface treatment depends on the substrate and is crucial for durability. Refer to the current Sika® Pre-treatment Chart for Marine Applications and verify with tests on original substrates.
Application
Process between 5 °C and 40 °C; reactivity and handling change with temperature and humidity.
Optimum substrate and product temperature is 15 – 25 °C.
Apply with hand, pneumatic, or electric piston guns, or suitable pump equipment.
Tooling & Finishing
Tool within the skin time.
Recommended finishing agent: Sika® Tooling Agent N (test any alternative agent for suitability).
Cleaning & Removal
Uncured material: remove from tools/equipment with Sika® Remover-208 or a suitable solvent.
Cured material: remove mechanically (e.g. knife, wire, abrasion).
Skin/hands: clean immediately with Sika® Cleaner-350H towels or an appropriate industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Best painted after skin formation; performance can be improved by treating the joint surface with Sika® Aktivator-100 or Sika® Aktivator-205 before painting.
If the paint requires baking > 80 °C, allow the sealant to fully cure first.
Always conduct preliminary trials under manufacturing conditions.
Avoid using enamel, alkyd, and chlorinated rubber paints on the joint area.
Compliance & Approvals
Meets requirements set out by the International Maritime Organization (IMO).
Associated with the marine “Wheelmark” conformity mark under the Marine Equipment Directive (MED) where applicable.
FAQs
Can Sikaflex®-291 be overpainted?
Yes, once cured and after preliminary testing for compatibility. Note that paint elasticity is usually lower than the sealant’s and may crack over the joint. Enamel, alkyd, and chlorinated rubber paints should not be used on the joint area.
What is a “marine grade” sealant/adhesive?
Sika’s marine range is designed for flexible, waterproof, and durable assemblies across vessels from small yachts to large ships, for maintenance and construction tasks above and below the waterline.
When and why should a primer be used?
Primers promote adhesion on certain substrates. Sika® Primer-210 is commonly used prior to applying 1-component polyurethanes like Sikaflex®-291. Always confirm with testing.
What does the Wheelmark indicate?
The Wheelmark symbolizes conformity with marine equipment standards under the EU Marine Equipment Directive (MED).
Which substrates does Sikaflex®-291 bond to?
Wood; metals, metal primers and 2-C paint systems; ceramics; and plastics such as GRP. Avoid plastics prone to stress cracking (e.g. acrylic/Plexiglas®, polycarbonate).
How do I remove Sikaflex®-291?
Uncured: Sika® Hand Wipes or Sika® Remover-208 for tools/surfaces. Cured: mechanical methods (knife, wire, abrasion). Remover-208 will not remove cured material.
Important: Information above is based on typical data. Performance depends on substrate, preparation, joint design, and application conditions. Conduct on-site tests to verify suitability. Always consult the latest Technical Data Sheet (TDS) and Safety Data Sheet (SDS).
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive
All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation.
Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing.
Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions.
Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including:
Expansion joints in walls and cladding
Sealing around doors and window frames
Sealing penetrations in walls and floors for pipes
Sealing joints in concrete and masonry elements
Sealant for draught-proofing and general sealing and filling applications
Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on:
Aluminium
Steel
Powder-coated metals or glazed tiles
Concrete, aerated concrete, cement-based renders, mortars, and bricks
Application of Sikaflex® Pro+
Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.)
Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face.
Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying.
Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish.
Remove the masking tape and clean up immediately.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive
All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation.
Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing.
Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions.
Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including:
Expansion joints in walls and cladding
Sealing around doors and window frames
Sealing penetrations in walls and floors for pipes
Sealing joints in concrete and masonry elements
Sealant for draught-proofing and general sealing and filling applications
Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on:
Aluminium
Steel
Powder-coated metals or glazed tiles
Concrete, aerated concrete, cement-based renders, mortars, and bricks
Application of Sikaflex® Pro+
Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.)
Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face.
Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying.
Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish.
Remove the masking tape and clean up immediately.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal White: The Multipurpose Adhesive & Sealant
Product Overview
Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects.
Key Advantages
Bonds to a plethora of substrates without the need for surface pre-treatment
Excellent adhesion to damp concrete
Compatible with a multitude of construction materials
Strong mechanical and weathering resistance
CE Marking for quality assurance
Usage
Sikaflex®-111 is perfect for bonding and sealing the following materials:
Concrete
Masonry
Most stones
Ceramic
Wood
Metal
Glass
Various Plastics
Packaging
Available in 290 ml cartridges, 12 per box.
Application Instructions
Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal® Super-200 is great for sealing of connection joints with moderate movement
Good UV resistance
Low odour
For exterior and interior use
USE
Sealing of connection joints with moderate movement around windows, window sills, doors, PVC pipes, dry partition walls and ceiling
Filling of cracks on interior and exterior walls (with no permanent water immersion)
CHARACTERISTICS AND ADVANTAGES
For exterior and interior use
High movement capability ±12.5%
Good UV resistance
Solvent-free, low odour
Overpaintable
Very good adhesion on most construction materials such as concrete, plaster, wood
Possible storage at -10°C for short period of time (max 24h)
Conforms to EN 15651-1 F INT EXT
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
DESCRIPTION
SikaSeal® Acrylic 100 is a flexible, one component, water based acrylic joint sealant and gap filler where low demand of elongation are required, for interior use.
USES
SikaSeal® Acrylic 100 is suitable for sealing low movement joints around:
? brick
? Concrete
? Plasterboard
? Windows
? Doors
? Ceramic tiles
SikaSeal® Acrylic 100 fills cracks and adheres to:
? Glass
? Wood
? Aluminium
? Brick
? Concrete
? Plasterboard
? Ceramic
? Painted surfaces.
CHARACTERISTICS / ADVANTAGES
Excellent adhesion to most common construction materials.
Water clean-up of uncured sealant.
Can be sanded back once fully cured if required to give smooth surface finish.
Can be painted over using water based paints.
Non-toxic
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal® Roof & Gutter Silicone Sealant
Product Type: 1-component neutral cure roof and gutter silicone sealant
Product Overview
SikaSeal® Roof & Gutter is a versatile, one-component, neutral curing silicone sealant designed for use in roofing and guttering applications. This sealant offers excellent adhesion to a variety of construction materials and is ideal for sealing roofs, gutters, and plumbing fixtures, both for exterior and interior applications. It cures quickly and provides a flexible, waterproof seal with superior temperature resistance.
Key Features
Neutral cure, low odour formula
Excellent adhesion to common construction materials such as glass, metals, ceramics, tiles, plastics, concrete, and rubber
Fast curing with a non-sag formula for easy application
Interior and exterior use with a temperature resistance range of -40°C to +150°C
High movement capability (±25% for translucent, ±50% for coloured variants)
Waterproof seal for durable, long-lasting performance
Non-toxic and water-potable approved per AS/NZS 4020:2018
Applications
SikaSeal® Roof & Gutter is ideal for:
Roof and gutter sealing
Sealing polycarbonate roof sheeting
General sealing around plumbing fixtures and penetrations
Sealing interior and exterior joints
Specifications
Packaging
300ml cartridge
Shelf Life
12 months (if stored properly)
Colours Available
Translucent, Grey, White, Black
Density
Translucent: ~1.02 kg/l, Colours: ~1.39 kg/l
Shore A Hardness
Translucent: ~26, Colours: ~46
Elongation at Break
Translucent: ~250%, Colours: ~310%
Movement Capability
Translucent: ±25%, Colours: ±50%
Service Temperature
-40°C to +150°C
Application Instructions
Ensure the substrate is clean, dry, and free from oils, grease, dust, and other contaminants. For optimal adhesion, follow the recommended priming procedures based on the substrate type (non-porous or porous). Apply SikaSeal® Roof & Gutter using a sealant gun, ensuring full contact with the joint sides. Tool the sealant immediately after application for a smooth, durable finish.
Important Considerations
Do not apply on natural stone or bituminous substrates
Not recommended for use under water pressure or in permanent water immersion
Pre-test required on stressed polyacrylate and polycarbonate materials
May cause discoloration on light-colored silicone when exposed to UV radiation (this does not affect the product's performance)
Not suitable for use in confined spaces with no air circulation (requires atmospheric moisture to cure)
Packaging & Storage
Store in the original, unopened packaging in a dry location between +5°C and +25°C. Shelf life is 12 months from the production date under proper storage conditions.
Contact & Ordering
For more information or to place an order, contact us at admin@gluesaustralia.com.au
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Usage
Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates.
Advantages
Up to 4 hours fire resistance according to AS 1530.4
Up to 4 hours fire resistance according to EN 1366-4
Very good resistance to weathering
Movement capability of ± 35% (ASTM C 719)
Easy to smooth and very good workability
Good adhesion to many different substrates
Neutral curing
Colour
Grey
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKASIL® -670 FIRE | JOINT SEALANT
Fire-rated joint sealant
Up to 4 hours fire resistance according to EN 1366-4
Very good resistance to weathering
Easy to smooth and very good workability
DESCRIPTION
Sikasil®-670 Fire is a fire-rated, 1-component, moisture-curing, low-modulus elastic joint sealant.
USES
Sikasil®-670 Fire is designed for fire rated movement
and connection joints on porous and non-porous substrates.
CHARACTERISTICS / ADVANTAGES
▪ Up to 4 hours fire resistance according to EN 1366-4
▪ Very good resistance to weathering
▪ Movement capability of ± 35% (ASTM C 719)
▪ Easy to smooth and very good workability
▪ Good adhesion to many different substrates
▪ Neutral curing
ENVIRONMENTAL INFORMATION
▪ LEED® EQc 4.1
▪ SCAQMD, Rule 1168
▪ BAAQMD, Reg. 8, Rule 51
APPROVALS / STANDARDS
▪ EN 15651-1 F EXT-INT CC 25 LM
▪ EN 15651-4 PW INT
▪ ISO 11600 F 25 LM & G 25 LM
▪ ASTM C 920, class 35
▪ EN 1366-4 assessment report
▪ ETAG 026 assessment report
▪ EN 13501-2 classification report
▪ EN 140-3
▪ EN 13501-1 class B-s2-d0
PRODUCT INFORMATION
Chemical Base Neutral cure silicone
Colour: Grey
Storage Conditions Sikasil®-670 Fire shall be stored in dry conditions, where it is protected from direct sunlight and at temperatures between +5 °C and +25 °C.
Density 1.35 kg/l approx. (ISO 1183-1)
TECHNICAL INFORMATION
Shore A Hardness 16 approx. (after 28 days) (ISO 868)
Secant Tensile Modulus 0.30 N/mm2 approx. at 100% elongation (23 °C) (ISO 8339)
0.50 N/mm2 approx. at 100% elongation (−20 °C)
Elongation at Break 650% approx. (ISO 37)
Elastic Recovery 70% approx. (ISO 7389)
Tear Propagation Resistance 4.0 N/mm approx. (ISO 34)
Movement Capability ±25% (ISO 9047) ±35% (ASTM C 719)
Service Temperature −40 °C to +150 °C
Joint Design The joint width must be designed to suit the joint movement required and the movement capability of the sealant. The joint width shall be ≥ 10 mm and ≤ 40 mm. The joint depth shall be ≤ 20 mm. A width to depth ratio of 2:1 must be maintained (for exceptions, see table below).
Backing Material Use polyethylene foam backing rods.
Sag Flow 2 mm approx. (20 mm profile, 50 °C) (ISO 7390)
Ambient Air Temperature +5 °C to +40 °C, min. 3 °C above dew point temperature
Substrate Temperature +5 °C to +40 °C
Curing Rate 2 mm/24 hours approx. (23 °C / 50% r.h.) (CQP 049-2)
Skin Time 25 minutes approx. (23 °C / 50% r.h.) (CQP 019-1)
Tooling Time 20 minutes approx. (23 °C / 50% r.h.) (CQP 019-2)
APPLICATION INSTRUCTIONS
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikasil®-670 Fire adheres without
primers and/or activators
APPLICATION METHOD / TOOLS
Sikasil®-670 Fire is supplied ready to use.
After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a foil pack or cartridge into the sealant gun and extrude Sikasil®-670 Fire into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikasil®-670 Fire sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents.
CLEANING OF TOOLS
Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® TopClean T. Once cured, residual material can only be removed mechanically.
FURTHER DOCUMENTS
▪ Safety Data Sheet (SDS)
▪ EN 13501-2 classification report
▪ ETAG 026 assessment report
▪ Brochure Sika Fire Protection Solutions
LIMITATIONS
▪ Sikasil®-670 Fire cannot be overpainted.
Colour variations may occur due to exposure to chemicals, high temperatures and/or UV-radiation (especially with the colour shade white). However, a change in colour is purely of aesthetic nature and does not adversely influence the technical performance or durability of the product.
▪ Do not use Sikasil®-670 Fire on natural stone.
Do not use Sikasil®-670 Fire on bituminous substrates, natural rubber, EPDM rubber or on any building materials which might bleed oils, plasticizers or solvents that could attack the sealant.
▪ Do not use Sikasil®-670 Fire to seal joints in and around swimming pools.
▪ Do not use Sikasil®-670 Fire for joints under water pressure or for permanent water immersion.
▪ Do not expose uncured Sikasil®-670 Fire to alcohol-containing products as this may interfere with the curing reaction.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaTitan®
258 is a primerless to windscreen, one-component direct glazing adhesive. It is easy to apply and has a paste-like consistency. On exposure to atmospheric moisture it cures to a durable elastomer. SikaTitan® -258 provides a long tack-free time and ensures a safe application even under warm conditions. Note: Primerless application requires the glass to be prepared with a non-antistatic glass cleaner.
Also the bonding surfaces must be free of contamination prior to the application of the adhesive. SikaTitan® -258 is manufactured in accordance with ISO 9001 / 14001 quality assurance system and with the responsible care program.
Product Benefits
- Primerless to glass
- One-component formulation
- Cold application
- Good application properties such as bead stability / good non-sag properties
- Short cut-off string
- Tested according to FMVSS 212/208 (with double-side airbags, no seatbelts)
Areas of Application
SikaTitan® -258 is suitable for direct-glazing applications in the Automotive Glass Replacement business. With its good performance and application properties it is suitable for mobile as well as inhouse installations.This product is to be used by professional experienced fitters only. If this product is used for other applications than Automotive Glass Replacement, trials must be carried out prior to use.
Technical Product Data
Chemical base 1-C polyurethane
Colour (CQP1) 001-1) Black
Cure mechanism Moisture-curing
Density (uncured) (CQP 006-4) 1.1 kg/l approx.
Non-sag properties (CQP 061-1) Good
Application temperature +5 to +40°C Skin time2)
(CQP 019-1) 40min. approx.
Open time2)
(CQP 526-1) 30min. approx.
Curing speed(CQP 049-1)
Shore A hardness (CQP 023-1 / ISO 868) 51 approx.
Tensile strength (CQP 036-1 / ISO 37) 5 MPa approx.
Elongation at break (CQP 036-1 / ISO 37) 650% approx.
Tensile lap-shear strength (CQP 046-1 / ISO 4587) 2.5 MPa approx.
Safe Drive-Away Time2)
(cars) with double side airbag
according to FMVSS 212 / 208 (CQP 511-1) without airbag
6 hours
2 hours
Chemical Resistance
SikaTitan® -258 is resistant to fresh water, seawater, limewater, sewage effluent, diluted acids and caustic solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic acids and caustic solutions or solvents.
Method of Application
Removal of old glass
Remove damaged glass in accordance with the vehicle manufacturer’s instructions.
Surface preparation
Surfaces must be clean, dry and free from dust and grease. The bond faces must be prepared with a non-antistatic glass cleaner.
Bonding surface must be free of contaminants before application of the product. Windshields without ceramic coatings need additional UV protection.
Application
Cut off the tip of the nozzle in accordance with the vehicle manufacturer's recommendations and screw onto the cartridge. It is recommended to apply the adhesive with a piston-type application gun. To ensure a uniform thickness of adhesive bead, we recommend that the adhesive be applied in the form of a triangular bead (see fig. 1 below).
The substrate temperature must be between 5°C and 35°C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal®-401 Aquarium
Premium one-component aquatic life safe silicone sealant
SikaSeal® 401 Aquarium is a premium one-component room temperature vulcanising (RTV) silicone rubber that is safe for aquatic life and designed for sealing applications in aquariums, ponds and water pumps. It adheres very well to glass and aluminium, is UV resistant and has excellent gap filling properties.
Extreme temperature resistance (-50°c to +250°c)
Excellent vibration, UV and weathering resistance
Good gap filling properties
Usage
Fish tanks
Water pumps
Aluminium
Glass
Advantages
Extreme temperature resistance (-50°c to +250°c)
Excellent vibration, UV and weathering resistance
Good gap filling properties
Highly versatile
Easy to apply
Aquarium safe
Composition
1-C Silicone (acetoxy)
Shelf life
18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions.
Storage conditions
Must be stored in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Density
~1.02 kg/l
Application
Application steps
SUBSTRATE PREPARATION
Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue free solvent and allow to completely dry.
CLEANING OF EQUIPMENT
Uncured, excess SikaSeal® 401 Aquarium may be removed with Sika® Remover- 208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife.
PRODUCT INFORMATION
Composition 1-C Silicone (acetoxy)
Packaging 75g Tube, 12 Tube per box
Colour Clear
Shelf life 18 months from date of production if in undamaged and unopened original sealed containers and stored according to the storage conditions.
Storage conditions Must be stored in dry conditions and protected from direct sunlight at
temperatures between +10ºC and +25ºC.
Density ~1.02 kg/l
Shore A Hardness ~23
Tensile Strength 1.0 N/mm2
Secant Tensile Modulus 1.1 n/mm2
Elongation at Break ~500%
Ambient Air Temperature +5°c to +45°c
Curing Rate ~3mm per 24 hours
Skinning time ~7-10 minutes
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond is a high strength contact adhesive that will not slump on vertical surfaces. It can be used as a one way liquid adhesive, or a two way contact adhesive, on a variety of surfaces.
Uses SikaBond can be used on most substrates due to its excellent adhesion.
These include:
Floor and wall panels.
Wood, plasterboard and chipboard.
Aluminium, iron and steel.
Concrete, cement sheeting and masonry.
Advantages
One component ready to use.
Fast drying time.
Easy to use.
High adhesion strength.
Non-slump.
Storage and Shelf Life
Stored in the original sealed packaging at temperatures of between 5ºC and 35ºC, this material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking must be removed and light sanding is recommended.
Application
One Way Method:
This method is recommended for heavier panels or where load or stress is expected. Apply a 4 to 6mm bead of SikaBond using a cartridge gun, making sure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges.
Two Way Method:
Apply adhesive as in one way method, bring together substrates, and press firmly over entire surface to transfer adhesive. Then pull apart. Allow adhesive to tack off for 3 to 5 minutes depending on weather conditions, reposition the objects and press together firmly. The surfaces should be tapped together with a hammer and a padded block to ensure maximum contact. Maximum bond strength will be achieved in 12 to 72 hours, depending on substrates and weather. Heavy panels may require temporary mechanical fastening until maximum strength is achieved.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Instant set, high viscosity, multipurpose super glue
Suitable for bonding substrates with irregular surfaces and in vertical applications
Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals
Controlled dosage applicator nozzle
Use:
As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials
Can be used on porous substrates such as porcelain and china
Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc.
Surfaces with small irregularities max. 0.5 mm
On vertical surfaces
Characteristics and Advantages
One Component
Easy to apply, non-sag, gel consistency
Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card
Low consumption adhesive
Versatile, allows adhesion between different materials
Colourless
Durable
Packaging
3 g Tube
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Medium viscosity, ethyl cyanoacrylate based instant setting adhesive where very fast cure speed is required.
Features:
-Instant set, medium viscosity, multipurpose super glue
-Suitable for bonding substrates with smooth surfaces
-Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals
-Controlled dosage applicator nozzle
Use:
-As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood, paper and other materials. It is especially suitable for bonding pieces with very smooth surfaces.
-Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc.
Characteristics and Advantages
-One Component
-Easy to apply, middle viscosity
-Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper
-Low consumption adhesive
-Versatile allows adhesion between different materials
-Colourless
-Durable
Colour: Clear
Shelf-Life: 12 months from the date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at
temperatures between +5°C and +25°C. Refrigeration to +5°C gives optimum storage stability.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Instant set, low viscosity, multipurpose super glue
Suitable for bonding substrates with very smooth surfaces
Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals
Controlled dosage applicator nozzle
Use:
As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood and other materials. It is especially suitable for bonding pieces with very smooth surfaces.
Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc.
Characteristics and advantages:
One Component
Easy to apply, low viscosity
Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, leather
Low consumption adhesive
Versatile allows adhesion between different materials
Colourless
Durable
COLOUR
Clear
Storage
12 months from date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5ºC and +25ºC. Refrigeration to +5ºC gives optimum storage stability.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond Fast is a premium, water-based, multi-purpose construction adhesive providing strong initial grab and high bond strength.
Uses:
SikaBond Fast can be used on most substrates due to its excellent adhesion.
These include:
- Fixing polystyrene wall panels
- Replacing loose tiles on walls
- Skirting boards, architraves and trims to walls
- Bonding panels to wall studs
- Bonding particleboard, plywood, fibre cement and strip flooring to joists
Advantages :
- Complies to AS2329-1980, “Mastic Adhesives for Fixing Wallboards”
- Natural wood colour
- Reduces the number of mechanical fasteners required to install floors or walls.
- Can be repositioned for up to 60 minutes after application
- Reduces squeaking associated with nail ride in floors
- Paintable with water-based surface coatings
- Easy to use one component
- Bridges gaps up to 9 mm
- Strong adhesion to metal
- No fumes
- High bond strength and heat resistance
- Flows easily at all temperatures
- Easy cleanup
- Fast initial grab – minimises slippage on vertical surfaces
Storage and Shelf Life
Stored in the original sealed packaging at temperatures of between 5oC and 35oC, this material will keep for at least two (2) years.
Instructions for Use
Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking material must be removed and light sanding is recommended. SikaBond Fast will adhere to damp (not wet) substrates but drying times may increase. Substrates should be above 5ºC. Do not bond 2 non-porous substrates ensure that one surface is porous.
Application
Apply a 5 mm bead of SikaBond Fast to one surface using a cartridge gun; ensure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges.
Cleaning
The uncured material can be cleaned with water. The hardened material can only be removed by mechanical means.
Technical Data (Typical)
Colour Pale Brown
Specific Gravity ~ 1.4
Skinning Time 20 minutes
Repositioning Time 60 minutes
Full Cure 24 hours depending on conditions
When both surfaces are porous firm, a slip-resistant bond will develop after 15 minutes at 30ºC and 60 minutes at 10ºC. Should one surface be non-porous or the substrate damp, a firm slip resistant bond will be achieved in approximately 8 hours. After 24 hours, 90% of the final strength will be achieved. (dependant on temperature, the porosity of the substrates, humidity and ventilation).
Service temperature -5ºC to +90ºC
Packaging 420 gram cartridge (12 cartridges per box)
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® - PVA is a high solids, one part Cross-linking PVA which meets the D3/BS EN204 specification. SikaBond® - PVA is an ideal product for bonding a wide range of timber components including tongue and groove solid timber and laminated flooring substrates giving tough, flexible permanent bonding.
Uses
SikaBond® -PVA can be used on most substrates due to its excellent adhesion. These include:
Timber
MDF boards
Particle boards
Ply woods
Advantages
- Excellent water resistance
- High bond strength within 24 hours
- Suitable for interior and exterior applications
Storage and Shelf Life
Store in a cool, dry place with 25oC maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Surfaces to be bonded should be clean, dry and free from dust and oil. Edges should be squarely machined to ensure maximum contact.
Application
SikaBond® -PVA is to be applied by squeeze bottle, brush or roller. Bonds should be assembled within a few minutes and then tightly clamped or pressed until the adhesive has set. Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Assemblies are best left overnight before moving or transportation. Maximum bond strength is achieved within 48 hours. Allow floors 24 hours for the adhesive to cure prior to using. SikaBond® -PVA should be used as supplied.
Cleaning Wipe off adhesive squeeze out immediately after assembly with a dry or lightly damp cloth.
Colour: White
Density: 1.08 kg/L
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work.
Uses
SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include:
Wood
Stone
Metals
Glass
Ceramics
Concrete
Brick
Masonry
Advantages
Waterproof
Resistant to solvents and chemicals
Paintable with water based and solvent based paints
High adhesion strength
Storage and Shelf Life
Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous).
Application
Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations.
Colour: Brown
Density 1.11 kg/litre approx.
Bond Strength Tensile Strength - 3030kpa
Test Substrate - Timber: End grain to end grain
Viscosity 6,000cps
Handling Precautions
Avoid contact with skin and eyes.
Wear protective gloves and eye protection during work.
If skin contact occurs, wash skin thoroughly.
If in eyes, hold eyes open, flood with warm water, seek medical attention without delay.
A full Material Safety Data sheet is available from Sika on request.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond® SprayFix: The Ultimate Aerosol Spray Adhesive for Multipurpose Use
High-Performance, Fast-Drying, & Repositionable Adhesive
SikaBond® SprayFix is your go-to aerosol spray adhesive for both temporary and permanent bonding. With its high performance, low odour, and fast-drying time, it's designed for your convenience.
Key Advantages:
Easy to use
Low odour
Dries clear
Fast drying time (approximately 2-4 minutes)
High initial strength
Contains no chlorinated solvents - suitable for indoor use
Repositionable for 1-2 minutes
Applications Include:
Upholstery
Floor Repairs
Furniture Lamination
Art and Crafts (e.g., mounting prints)
Suitable Substrates:
Felts and Fabrics
Metals
Foams
Cork
Most Plastics
Rubber Gaskets
Fibreglass
Wood (e.g., plywood, particle board)
How to Use:
Ensure the surface is clean, dry, and free of dust and grease.
Shake the can well before use.
Hold the can approximately 80-100 mm from the surface and spray lightly.
Allow a few minutes for drying.
Packaging:
Available in 150g and 350g aerosol cans.
Color:
White when applied, clear when dry.
Cleaning of Equipment:
After use, invert the can and press the tip until clear propellant comes out for cleaning. Uncured overspray can be removed with Sika® Colma Cleaner or another suitable solvent.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant
Product Highlights
Fast Skinning
Low Odour
Paintable and Sandable
Resistant to Ageing
Silicone-Free
Product Usage
Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction.
Compatibility
Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates.
Packaging
Comes in a 310 ml cartridge for easy application.
Technical Specifications
Cure Mechanism: Moisture-curing
Application Temperature: 535°C
Shelf Life: 12 months when stored below 25°C
Application and Removal
For detailed application and removal guidelines, consult the manufacturer's manual.
Precautions
This product is intended for use by experienced professionals. Always perform tests for compatibility.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Sika SikaFlex 227: Your All-in-One Car Body Sealant
Product Highlights
Fast Skinning
Low Odour
Paintable and Sandable
Resistant to Ageing
Silicone-Free
Product Usage
Perfect for sealing, seam sealing, simple bonding, vibration reduction, and sound deadening in car body repair and construction.
Compatibility
Works well with metal primers, paint coatings, metals, and plastics. Always test before use on new substrates.
Packaging
Comes in a 310 ml cartridge for easy application.
Technical Specifications
Cure Mechanism: Moisture-curing
Application Temperature: 535°C
Shelf Life: 12 months when stored below 25°C
Application and Removal
For detailed application and removal guidelines, consult the manufacturer's manual.
Precautions
This product is intended for use by experienced professionals. Always perform tests for compatibility.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces
100% crystal clear / transparent
Good workability
Very good adhesion on many typical building materials
Use:
Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including:
Plasterboard
Wood surfaces
Painted enamel
Polyester
Plastic
Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions.
CHARACTERISTICS AND ADVANTAGES
100% crystal clear / transparent
Good workability
Low shrinkage during cure
Flexible and elastic
Can be used on damp concrete
Very good adhesion on many typical building materials
COLOUR: Transparent
Product Data
Appearance / Colours Transparent
Packaging 300 g cartridge (290 ml), 12 cartridges per box
Storage Conditions / Shelf-Life
Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met.
Technical Data
Chemical Base Silane terminated polymer
Density 1.05 kg/l approx. (ISO 1183-1)
Tensile Strength 2.0 N/mm2 approx. (ISO 37)
Shore A Hardness 30 approx. (after 28 days) (ISO 868)
Elongation at Break 400% approx. (ISO 37)
Elastic Recovery 70% approx. (ISO 7389)
Tear Propagation
Resistance
4.0 N/mm approx. (ISO 34)
Service Temperature −40 °C to +70 °C
SUBSTRATE PREPARATION
The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications,
such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed:
Non-porous substrates
Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints.
Porous substrates
Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department.
Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly.
Bonding
After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again.
Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear.
Sealing
After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents.
Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer.
USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction.
Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics.
CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free
Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts
Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic.
Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower
Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only.
Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart.
ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department.
Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility.
RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin!
OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer.
USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction.
Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics.
CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free
Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts
Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic.
Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower
Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only.
Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart.
ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department.
Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility.
RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin!
OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal Black: Seal, Bond, and Build with Ease
Product Overview
The one-stop solution for all your adhesive and sealing needsSikaflex®-111 Stick & Seal Black.
Advantages
Bonds effortlessly to a myriad of substrates with no surface pre-treatment needed
Excellent for use on damp concrete
Fully compatible with most construction materials
Durable against weathering and mechanical wear
CE Marked for quality assurance
Usage Scenarios
This versatile product is perfect for:
Concrete
Masonry
Stones
Ceramic
Wood
Metal
Glass
Plastics including PVC, PA, PET, and EPS/XPS
Packaging
Available in 290 ml cartridges, packed 12 cartridges per box.
Color Options
Also available in White and Concrete Grey.
Application Guidelines
For best results, the substrate should be free of contaminants. Further instructions for both porous and non-porous substrates are available.
Cleaning & Maintenance
Use Sika® Remover-208 for cleaning tools and Sika® Cleaning Wipes for skin.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal Grey: The Multipurpose Adhesive & Sealant
Product Overview
Experience the versatility of Sikaflex®-111 Stick & Seal, a 1-part adhesive and sealant that caters to both internal and external projects.
Key Advantages
Bonds to a plethora of substrates without the need for surface pre-treatment
Excellent adhesion to damp concrete
Compatible with a multitude of construction materials
Strong mechanical and weathering resistance
CE Marking for quality assurance
Usage
Sikaflex®-111 is perfect for bonding and sealing the following materials:
Concrete
Masonry
Most stones
Ceramic
Wood
Metal
Glass
Various Plastics
Packaging
Available in 290 ml cartridges, 12 per box.
Color Options
Choose from White, Concrete Grey, or Black to match your project requirements.
Application Instructions
Ensure the substrate is clean and free of contaminants for optimum adhesion. For detailed application instructions, please contact Sika Technical Services.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-291 Tube Black: Marine-Grade, Multipurpose Polyurethane Sealant
Product Benefits
IMO Certified
Bonds to a wide variety of substrates
Good ageing and weathering resistance
Elastic and low odour
Non-corrosive, Overpaintable and Sandable
Usage
Sikaflex®-291 is a multipurpose product suitable for marine constructions. It is ideal for making elastic, vibration-resistant joint seals and can also be used for interior sealing applications.
Application Information
Surface preparation is key. Surfaces must be clean, dry and free from grease, oil, and dust. Further application tips can be found in the Sika Pre-treatment Chart for Marine Applications.
Additional Details
Application Temperature: 5 ? 40 °C
Skin Time: 60 minutes
Shore A Hardness: 40
Shelf Life: 12 months when stored below 25°C
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium one component room temperature vulcanising silicone sealant
USE
Fridge and freezer sealing
Pizza oven sealing
Oven sealing
Aluminium
Glass
CHARACTERISTICS AND ADVANTAGES
High temperature resistance (-50 to 250OC)
Excellent adhesion
Gap filling properties
Heat proof
Vibration resistant
Highly versatile
PACKAGING: 300 ml cartridges
COLOUR: Black
SikaSeal® Appliance Silicone Sealant is a premium one component room temperature vulcanising (RTV) silicone rubber designed for flexible gasketing and sealing applications. SikaSeal® Appliance Silicone Sealant forms a tough but flexible seal of all shapes and sizes and fills any surface voids. The cured product can withstand vibration, weathering, temperature extremes, water oil and grease without hardening, shrinking or cracking.
Uses
Fridge and freezer sealing
Pizza oven sealing
Oven sealing
Aluminium
Glass
Characteristics / Advantages
High temperature resistance (-50 - 250°C)
Excellent adhesion
Heat proof
Gap Filling properties
Vibration resistant
Highly versatile
Product Data
Colour Black
Packaging 300ml Cartridge, 12 cartridges per box
Storage
18 months from date of production if stored in undamaged and unopened original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Technical Data
Chemical Base 1-C silicone
Density (uncured) 1.0 kg/l approx.
Skin Time 10 min approx.
Tack-free time 20 min approx.
Curing Time 24 hours approx.
Cure Mechanism Moisture-curing
Cure Type Acetoxy
Application temperature 5 - 45°C
Mechanical/Physical Properties
Tensile Strength 1.0 N/mm2 approx.
Shore a Hardness 25 approx.
Ultimate Elongation 600% approx.
Application Details
Ensure all surfaces are clean, dry and free from dust, grease and loose material. Remove all old gasket material from mating surfaces before cleaning with a residue-free solvent and allowing drying properly. Cut the nozzle at a 45° angle to the desired bead size (3 mm is suitable for most applications) then apply a continuous and even bead along the joint. Cure Mechanism SikaSeal® Appliance cures by reaction with atmospheric moisture. The reaction thus starts at the surface and proceeds to the core of the joint. The curing speed depends on the relative humidity, temperature and thickness of the sealant. At low temperatures, the water content of the air is lower and the curing reaction proceeds more slowly.
Clean Up Uncured, excess SikaSeal® Appliance may be removed with Sika® Remover-208 or another suitable solvent. Once cured, the excess sealant can be trimmed away from the edges with a knife.
Application Conditions/ Limitations
Restrictions On Use SikaSeal® Appliance is not recommended for use in applications where it will be permanently exposed to temperatures exceeding 250°C or in contact with fuels. The above information is offered for general guidance only.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaSeal® Kitchen and Bathroom
SikaSeal® Kitchen and Bathroom is a one-component, neutral-curing, low-odour silicone sealant with excellent adhesion and a long shelf life for DIY applications. It cures at room temperature under the action of atmospheric moisture to give a permanently flexible silicone rubber.
Uses
Glass and enamel
Ceramics and tiles
Aluminium, steel, zinc, copper
Plastic laminates
Rubber
Stainless steel
Concrete and grouts
Characteristics / Advantages
Excellent adhesion
Great weatherability
Non-sag
Great tooling characteristics
Long-term mould resistance
Interior and exterior usage
Fast curing
Colours
White
Beige
Black
Charcoal
Transparent
Alabaster
Almond Ivory
Off White
Stone
Pewter
Grey
Mid Grey
Stone
Brown
Packaging
300ml cartridges, 12 cartridges per box
Shelf Life
12 months from the date of production if stored in undamaged and unopened original sealed containers, in dry conditions, and protected from direct sunlight at temperatures between +10ºC and +25ºC.
Technical Data
Chemical Base: Neutral curing
Density: 0.98 g/cm³ @ 23ºC
Skin/Forming Time: 10-15 minutes @ 23ºC/50% r.h.
Curing Rate: 72 hours @ 23ºC/50% r.h.
Consistency: Non-sag
Mechanical/Physical Properties
Tensile Strength: 0.4 N/mm² @ 23ºC/50% r.h.
Shore A Hardness: 20 SHA
E-Modulus: 0.30 N/mm² at 10% elongation @ 23ºC/50% r.h.
Ultimate Elongation: 300%
Anti-mildew Property: 0 level
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sugru is a Multi-Purpose, Mouldable Glue for fixing, Bonding and DIY
Mouldable
Out of the pack, Sugru Mouldable Glues are designed to feel soft and malleable like play-dough. Roll the material in your fingers. Press it where you need it, and mould it by hand into any shape. From an ultra-thin patch to a shock-absorbing bumper, you have 30 minutes to shape it, smooth it, and reposition it as required.
Flexible
Leave for 24 hours. Thanks to some clever science and advanced technologies, Sugru Mouldable Glues react at room temperature, simply on exposure to air. They crosslink into strong, flexible and tactile silicone rubbers overnight. Sugru Mouldable Glues will flex with the materials they're applied to, so you can fix things that need to bend. They work like nothing else on leathers, fabrics or flexible plastics.
Waterproof & Durable
Once cured, Sugru Mouldable Glues are waterproof and long-lasting, just like other silicone rubbers. So you can use them in challenging environments like wet bathrooms, shower and sink areas – even outdoors with long-term exposure to the sun, sea and other weather conditions.
Multi-Material
Sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*.
Strong
Once cured, it stays in its shape permanently and will remain bonded, often for years to come.
Holds Up to 2KG/4.4LB
Ensure surfaces are clean and dry. A 5g/.17oz single-use pack can hold up to 400x its own weight.
Heat and Cold Resistant
Comfortable at high and low temperatures up to 180°C (356°F) and down to -50°C (-58°F).
Durable
Flexibility combined with strong adhesion ensures that your fixes don’t become brittle or crack.
Waterproof
Ensure surfaces are dry before use. It can even be used for sealing applications indoors and out.
Flexible
The thickness of your fix will determine its ultimate flexibility, a thin layer will deliver maximum flex.
Shock Resistant
Excellent dampening properties can deliver vibration resistance and shock protection.
Insulating
Like other silicones, it has good thermal and electrical insulation properties**.
Weatherproof
Excellent ozone and UV resistance. Only slight fading after years in direct sunlight.
Stick It
Sugru sticks permanently to lots of materials like glass, ceramic, wood, metal and plastics*.
Mould It
You have 30 minutes to fix, build and create.
Sets Strong
In 24 hours, it turns into a strong and durable silicone rubber that stays stuck.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force.
FEATURES:
Extreme tensile strength
1 loop of tape holds 700+ pounds of weight
Made with patented Forge-Link™ Technology
Waterproof backing
High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure
UV resistant materials
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Experience unmatched strength and durability with our T-Rex Ferociously Strong Tape, now available at Glues Australia. Measuring 9.14 meters in length, this tape is specifically designed to withstand the toughest situations and most demanding projects.
Crafted for homeowners, craftsmen, and outdoor enthusiasts, T-Rex® Tape distinguishes itself from ordinary duct tapes with its formidable holding power. This makes it your go-to solution for enduring repairs, creative DIY projects, or any challenging task you encounter. The secret to its exceptional performance lies in its aggressive double-thick adhesive. This feature allows the tape to adhere firmly to rough, dirty surfaces in all types of weather and temperature conditions.
T-Rex® Tape is more than just a tool; it's a reliable partner for both home use and professional job sites. It outlasts and outperforms regular duct tape, ensuring that your projects, big or small, are held together longer and stronger.
Key Features:
All-Weather Capabilities: Equipped with a waterproof backing, T-Rex® Tape stands resilient against harsh weather elements, even in the coldest temperatures. This feature makes it an ideal choice for outdoor repairs and applications.
Enhanced Durability: The tape boasts a high-tensile woven scrim, contributing to its strength and long-lasting nature. Whether it’s used for heavy-duty tasks or simple fixes, the tape’s robust construction ensures it won’t give in.
Superior Holding Power: With its double-thick adhesive, T-Rex® Tape grips onto rough and uneven surfaces with unparalleled strength. This makes it perfect for tasks that require a strong, reliable hold.
Versatile Usage: Suitable for both indoor and outdoor environments, the tape is manufactured using UV-resistant materials. These materials prevent the tape’s adhesive from weakening under harsh UV rays, extending its lifespan.
Wide Application Range: T-Rex® Tape is versatile enough to be used on a variety of surfaces, including brick, concrete, shingles, both painted and non-painted wood, and vinyl siding. This makes it a must-have in any toolbox.
Heavy-Duty Construction: Made with a heavy-duty knit cloth, the tape is designed for long-lasting repairs or applications. Whether it's for a temporary fix or a permanent solution, you can count on its reliability.
Usage Applications:
Home repairs, including fixing broken items and sealing leaks.
Crafting and DIY projects, offering creative flexibility.
Outdoor applications, including camping gear repairs.
Professional job site tasks, providing reliability and strength.
Why Choose T-Rex® Tape?
When you choose T-Rex® Tape, you're not just selecting a tape; you're choosing a commitment to excellence and reliability. Its unique composition allows it to withstand challenges that ordinary tapes can't handle. Whether you're a professional tradesperson or a DIY enthusiast, T-Rex® Tape is the perfect addition to your toolkit, providing a strong, durable solution for any project.
In conclusion, T-Rex® Tape is not just tape; it's a symbol of strength, resilience, and versatility. Its all-weather, UV-resistant features, combined with its superior adhesive strength, make it an indispensable product for anyone who values quality and reliability in their tools. Available now at Glues Australia – your trusted source for high-quality adhesive solutions.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
Features
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
FEATURES:
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
R-FLEX TECHNOLOGY
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
Features
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
T-Rex® Ferociously Strong Waterproof Tape provides tough waterproof adhesion under wet and dry conditions. Built with R-Flex Technology™, T-Rex Waterproof Tape can stretch up to 700% of its original length. It’s strong enough to be used for general purpose indoor or outdoor fixes that require a waterproof seal, like repairing a rip in an above-ground pool or temporarily stopping a leak in a water pipe. Or, apply it underwater and push it into cracks and rough, dirty surfaces. Formulated to withstand extreme temperatures from -56C to 93C., its UV-resistant formulation won’t break down under harsh sunlight. T-Rex Waterproof Tape. Flexible, ferociously strong, and waterproof like no other.
FEATURES:
Waterproof backing enhanced with R-Flex Technology™ for greater durability
Can be used underwater
UV resistant
All-weather: withstands temperatures from -56C to 93C.
WATERPROOF ADHESION
Extra thick butyl-based adhesive means durable repairs, even under water.
R-FLEX TECHNOLOGY
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
Durable, flexible and UV resistant backing for long lasting repairs.
ALL WEATHER
Waterproof and built to withstand extreme temperatures from -56C to 93C.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Tactix 25L Collapsible Storage Crate is a must-have for anyone looking to declutter their space easily and efficiently. Built from high-quality, durable plastic, this crate can hold up to 25 liters of tools, groceries, office supplies, or outdoor equipment, making it ideal for a wide range of uses. The crate’s collapsible design allows it to fold flat for easy storage when not in use, saving valuable space in your home, garage, office, or vehicle.
Whether you're organizing your garage, transporting work tools, or keeping your office supplies tidy, the Tactix 25L crate offers the perfect balance of strength and convenience. The ergonomic handles make it easy to carry, while its lightweight yet sturdy construction ensures long-lasting use. Use it to store gardening tools, sports gear, or even camping essentials—it’s perfect for both indoor and outdoor applications.
When you purchase from Glues Australia, you not only get premium products like the Tactix Collapsible Crate but also exceptional customer service. With fast delivery and a dedicated team ready to assist, we ensure a seamless shopping experience. Shop with confidence knowing you’re backed by Australia’s trusted adhesive and storage experts.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip 5min Epoxy is a two-part all purpose adhesive. When mixed equally together it provides a tough, rigid, high strength bond to tackle the toughest DIY projects. Its also fast - sets in 5 minutes and reaches initial handling strength in 30 minutes.
Easy mix
Durable bond
Dries clear
Water resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses.
An all-purpose glue which bonds almost everything
Grabs in minutes - the exact "grab time" depends on the surfaces to be joined
Fast drying
Water resistant
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance.
Incredible bond strength
Waterproof
Superior strength
Adheres to even visibly damp surfaces
Longer work time (10 minutes)
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](//gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
![Sika Sikaflex Pro+ Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](//gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](//gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](//gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](//gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](//gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](//gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
![Sika Sikasil Pool Silicone Water Resistance [White]](//gluesaustralia.com.au/cdn/shop/files/7612894609400_e5cdedf3-65af-430d-be37-52c0a1c7ff7a.png?v=1754711689&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Grey]](//gluesaustralia.com.au/cdn/shop/files/4063565057892.jpg?v=1754724118&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Red]](//gluesaustralia.com.au/cdn/shop/files/4063565066757.jpg?v=1754724118&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](//gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](//gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](//gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](//gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](//gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](//gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
![Sika Sikaflex 291 Marine Adhesive Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb4dfb0d-a336-4739-9b91-9ca89764b874.jpg?v=1754711704&width=645)
![Sika Sikaflex 291 Marine Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240096_bb9d6399-3f9c-4c6e-aeb9-97604f6829a6.jpg?v=1754711703&width=645)
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
![Sika Sikaflex Pro+ Sealant For Concrete and Masonry Facades 600ml [White]](http://gluesaustralia.com.au/cdn/shop/files/45205240085.jpg?v=1754724137&width=645)
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
![Sika SikaSeal Flexible Gap Filler Super-200 Paintable [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324010690_a135bef3-1e63-49fe-b52d-552f6c48153c.png?v=1754711651&width=645)
![Sika SikaSeal Gap Filler Acrylic 100 Sandable Paintable [White]](http://gluesaustralia.com.au/cdn/shop/files/9318324010676_f8ac62bc-ef55-4a57-a739-47528a1aae8c.jpg?v=1754711697&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9318324010461.png?v=1754724138&width=645)
![Sika SikaSeal Roof & Gutter Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324010454.png?v=1754724138&width=645)
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
![Sika Sikasil 670 Fire Resistant Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/7612895181462_fe2d5a8d-2a66-433f-9d24-2dfa9adec11a.jpg?v=1754711694&width=645)
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
![Sika Sikasil Pool Silicone Water Resistance [White]](http://gluesaustralia.com.au/cdn/shop/files/7612894609400_e5cdedf3-65af-430d-be37-52c0a1c7ff7a.png?v=1754711689&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524002800_e901daee-d941-4c51-bb2c-fdfedd9a6316.jpg?v=1754711662&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Grey]](http://gluesaustralia.com.au/cdn/shop/files/4063565057892.jpg?v=1754724118&width=645)
![Sugru Mouldable Glue - 3 Pack [Black White Red]](http://gluesaustralia.com.au/cdn/shop/files/4063565066757.jpg?v=1754724118&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/075353964668N_2b5bb515-b170-4a54-a924-8fcf58683e02.jpg?v=1754716416&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [9.14m]](http://gluesaustralia.com.au/cdn/shop/files/04007_14cbee25-54b9-43ad-a832-e4231871625b.jpg?v=1754716416&width=645)
