In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
Features
Superior formulation+ that stops mould growth*
Fast skinning formulation which means you can use your shower in 1 hour
Provides a durable waterproof seal
Resists lifting
Where can this product be used?
Suitable for use in humid and damp environments such as
Kitchens
Bathrooms
Laundries
Showers
Basins
tiles
Worktops
Baths & spas
Plumbing fixtures
What materials is this product suitable for?
Ceramic
Glazed & porcelain fixtures
Aluminium
Plastic laminates
Some rubbers
Glass
Stainless Steel
How to Use
Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould
Thoroughly clean surface where sealant will be applied with turps and dry completely
Cut nozzle at 45°angle, cut cartridge tip and fit nozzle
Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint
Tool with a spatula dipped in detergent water within 5-10 minutes of application
Clean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area
#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)
*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth
Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
Tips
For neater joints, mask sides before applying the sealant and remove the tape before sealant skins
Not paintable. Complete painting 7 days before applying the sealant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Oven Plus Heavy Duty Gel is a powerful, low-fume cleaning solution formulated to remove baked-on grease and grime from ovens, cookware and bakeware. Its thick gel formula clings to vertical surfaces for deep cleaning with minimal scrubbing. Designed for warm-surface application, it delivers excellent results without harsh fumes.
Surface Preparation
Ensure the area is well ventilated before starting.
Remove loose debris, racks, trays and oven accessories.
Warm the oven slightly (no hotter than 90 °C), then turn it off and allow it to cool for 10 minutes before applying the gel.
Protect surrounding surfaces such as benchtops and floors from splashes.
Wear protective gloves and safety goggles when handling the product.
Application Instructions
Shake the tube well before use.
Apply a thin, even layer of gel using the integrated brush or a dry sponge.
Coat surfaces in order: back wall, sides, oven floor, ceiling, and door.
Allow the gel to dwell for approximately 30 minutes. Do not let it dry out.
Wipe off with a damp cloth. For stubborn spots, use a non-scratch scourer.
Rinse thoroughly with water and dry before reassembling oven parts.
For trays and racks, apply gel evenly, leave for 30 minutes, then rinse and dry.
If cleaning carbon steel or cast iron cookware, dry and oil immediately to prevent rust.
Coverage
A 400 g tube typically covers a standard oven interior and racks in one application, depending on the level of buildup and thickness of application.
Drying / Dwell Time
Allow the product to sit for around 30 minutes. Do not exceed the recommended dwell time. Wipe and rinse thoroughly once the gel has loosened the grime.
Cleanup
Remove residues with a damp cloth or sponge. Rinse thoroughly with clean water to remove any remaining product. Avoid rinsing directly into drains. Dispose of waste according to local guidelines.
Technical Data
Form: Thick gel
Colour: Clear to light blue
pH: 13–14 (strongly alkaline)
Density: Approximately 1.17 g/cm³
Viscosity: ~1,100 cP
Water solubility: Completely miscible
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Paint Over Sealant is a permanently paintable sealant.
Features
Paintable
Smooth flawless finish.
Easy to use and can be used on damp surfaces.
Superior adhesion to most building materials.
Low odour so can be used in any environment without discomfort.
Weather resistant by forming a durable seal which remains flexible, not drying or cracking
Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch.
Temperature resistance – approximately -40°C +93°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
May be discoloured by contact with alloys containing brass, copper or zinc.
Do not allow unused product to freeze.
Where can this product be used?
10879.Window frames that need painting
102879.Capstones Masonry walls that need painting
Perfect for use on or around:
Bricks and concrete
Windows frames
Tiled and wooden fixtures
Areas where a sealant is needed and where you want to paint it
Not suitable for use in below waterline applications.
Not suitable for use on oily woods such as cypress, teak or cedar.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Glass
Aluminium
Fibre Cement
Painted Surfaces
Ceramics
Masonry
Most metals
Most plastics
Wood
How to use this product
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant.
Remove the tape before the sealant skins.
For a better finish use a spatula dipped in detergent and water to tool off the sealant.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
To improve the paint finish, wipe the sealant with detergent solution immediately before painting.
Avoid smearing sealant on the surrounding surfaces as this may effects its paintability.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Porcelain Fix is a high strength two part white epoxy adhesive filler in a handy dual syringe. Specifically designed to fill and repair cracks, chips and breakages in porcelain, enamel and crockery.
Features
-High Strength – 2 part epoxy mix ensures high strength
-Achieves maximum bond within 8 hours
-Generous working time – Up to 10 minutes at 20°C
-Can be sanded
-Dries white and can be painted over
-Heat resistant to 93°C
-Can be used as gap filler – i.e. if join of breakage does not match up perfectly
-Can be tinted
Where can this product be used?
-For bonding & filling: China, pottery, porcelain, ceramics, Earthenware
-Repair a chipped sink
-Repairing broken crockery – plates, cups, bowls etc
-Fix a chip in your porcelain or enamel basin or bath
-Repairing chips or replacing a broken section of your toilet
-Should not be used on objects subject to high temperatures such as ovens and dishwashers.
What materials is this product suitable for?
China
Pottery
Porcelain
Ceramics
Earthenware
Bathroom fittings
How to use this product
-Surfaces joined should be clean and dry.
-Remove cap and pierce seal in each nozzle with the spatula/pin provided.
-The dual syringe will dispense equal portions of Part ‘A’ and Part ‘B’. Mix thoroughly.
-Apply to one surface, then bring together and hold using tape, weights etc.
-Once cured this product is extremely difficult to remove. Any material squeezed out of joints or split is best removed before it sets using Solvent Acetone or Methyl Ethyl Ketone solvent.
-Wipe nozzles after use. Pull the plunger back slightly and replace cap firmly over nozzles.
Handy tips
-For filling only, can be tinted with iron oxide or other dry pigments which must be mixed in very thoroughly.
-Softens at high temperatures, but strength returns when cooled.
-Wear protective gloves and eye protection when mixing or using.
-Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
-Clean up excess material with Acetone immediately. Once set the product cannot be removed easily
-To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
-To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Safety tips
-Avoid contact with skin and eyes and avoid breathing its vapours.
-Wear protective gloves when mixing and using.
-If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 13 11 26 or New Zealand 0800 764 766.
-If swallowed DO NOT induce vomiting. Give a glass of water and seek medical advice.
-If skin contact occurs, remove contaminated clothing and wash skin thoroughly. If in eyes, hold eyes open, flood with water for at least 15 minutes and see a doctor.
-For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Store syringe in an upright position with nozzles uppermost, in a cool dry location, away from direct sunlight.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS.
Features
Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS
Shock resistant, giving you a longer-lasting fix
Fast setting in 30 seconds
Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper
*Does not work on PTFE (Teflon)
Where can this product be used?
To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control
What materials is this product suitable for?
ALL plastics* including polyethylene, polypropylene and ABS
Metals
Timber
China
Rubber
Leather
Paper
How to Use
Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface.
Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise.
Remove cap and apply a small amount of glue to one surface only.
Limitations:
Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam.
Product only works on some rubbers and will not work on PTFE. May cause leather to harden or discolour, test on an inconspicuous area first.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue.
Features
Bonds a variety of surfaces
Extremely fast setting
Dries Clear for clean, neat results
Water resistant
No clamping necessary
No mixing required
Maximum strength achieved in 12 hours
Only takes 45 seconds to achieve an initial bond
Self-piercing, clog-free cap
Forms a strong, flexible bond
Impact Resistant – 4 times greater impact resistance than normal supa glues
Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues
Heat Resistant to 120°C permanently, 150°C intermittently
Comes with a nozzle for easy, accurate application
Appearance
Clear thick liquid dries to a colourless film.
Where can this product be used?
Ideal for small repair jobs or when immediate results are required
Fixing a broken door knocker
Refixing wooden or metal door handles
Repairing crockery safe to put in the dishwasher
Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Not suitable for repairing items that are in direct contact with hot liquids eg saucepans
Will not permanently bond glass or other materials containing alkaline elements
Not recommended for highly porous surfaces
What materials is this product suitable for?
Bonds a variety of porous and non-porous surfaces
Metals
Wood
China
Rubber
Leather (test first as leather may become hardened or discoloured)
Some plastics
How to use this product
Supa Glue works best when the surfaces to be bonded are close fitting.
Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips.
Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise.
Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure.
Allow 12 hours for sufficient bond strength for practical use.
Handy tips
Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue.
Excellent when used with other adhesives, as the temporary tack.
For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting.
After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water.
Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin.
While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer.
Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions.
Supa glues cure more slowly when large amounts are used. For faster cure use sparingly.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method.
Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin.
Do not use near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site.
Storage and re-use
After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly.
Ensure cap is replaced and store in a cool dry place.
For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula
Superior flexibility with +/- 25% movement capability
Temperature resistance: approximately -60°C to +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25-year guarantee* against crumbling, cracking, and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm²/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass, and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics, including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula
Superior flexibility with +/- 25% movement capability
Temperature resistance: approximately -60°C to +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25-year guarantee* against crumbling, cracking, and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm²/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass, and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics, including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters.
Features
UV and weather-resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non-corrosive neutral cure formula.
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Available in a range of Colorbond® colours to make it easier to select the right colour for the job
Cured sealant at area to volume ratios up to 2500mm2/L
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof & Gutter Ezi Press is easy to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and excellent UV and weather resistance. Ideal for roofing, guttering and flashing outside the home.
Best for: Aluminium, Sheet Metal, Copper, Brass, Galvanised Metals, Rigid PVC and most plastics including polystyrene, Terracotta, Concrete, Glazed tiles, BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
UV and weather resistant
Precision application for the best finish
Where can this product be used?
Metal and tile roofing
Colorbond roofs and fences
Guttering and flashings
Skylights
Around air conditioning units
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Use in a well ventilated are. Avoid contact with skin and eyes.
Throughly clean and dry surface from oil, dirt and grease with mineral turps.
Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Do not use in below ground applications.
• Sealant is not paintable. Complete painting 7d prior to applying sealant.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Sealant & Adhesive Remover 375g helps soften and lift old sealants and sticky residues so you can cleanly remove them and re-seal with confidence. The non-drip formula clings to joints and vertical surfaces, making bathroom and kitchen refreshes faster and easier.
Key benefits
Softens cured silicone and many common sealants to aid scraping and removal
Helps break down adhesive residue, tapes and grime build-up
Non-drip gel action for vertical joints, corners and trims
Low mess application with excellent wetting of tight gaps
Preps surfaces for fresh re-sealing and re-bonding
Where to use
Bathrooms: around showers, baths, basins and splashbacks
Kitchens and laundries: benchtop perimeters, sinks and tiles
Windows and doors: frames, trims and glazing edges
Suitable substrates
Glass, ceramic tiles, porcelain, enamel, stainless steel and many metals
Some plastics and laminates (always test first in an inconspicuous spot)
Not recommended on
Natural stone, marble or porous tiles
Freshly painted, delicate or lacquered surfaces
Acrylic and polycarbonate sheets, mirror backings and other sensitive plastics
Directions
Cut away and remove as much old sealant as possible with a plastic scraper.
Protect surrounding areas. Shake or stir if required, then apply a generous layer to remaining residue.
Allow time for the remover to penetrate. Dwell time will vary by sealant type and thickness.
Gently scrape and wipe away loosened material. Reapply if needed for stubborn spots.
Wash the area with warm soapy water, rinse and dry thoroughly before re-sealing.
Pro tips
Score thick beads along the edges with a utility blade before application to help penetration.
Work in manageable sections and avoid letting the remover dry on the surface.
Always test on a small hidden area to check surface compatibility.
Safety
Use in a well ventilated area and wear gloves and eye protection.
Avoid contact with skin and eyes. Keep out of reach of children.
Product details
Brand: Selleys
Type: Sealant and adhesive remover
Pack size: 375g
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs.
Features
Easy to use
Strong
Flexible Bond
Weather resistant
Impact resistant
Appearance
Dries yellowish/beige
Where can this product be used?
Sole
Tongue
Strap
Inner sole
Attach beads, jewels, decorative items
Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles.
What materials is this product suitable for?
Leather
Canvas
Fabric
Rubber
Cork
Most Plastics
EVA foam (e.g Desert boots sole)
How to use this product
Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal.
For larger area repairs such as shoe soles, we recommend you use the contact bond method:
For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes).
Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications.
For smaller areas, either use the contact method as above, or join with a wet bond:
Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry.
Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s.
Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries.
Handy tips
A piece of plastic from a takeaway container makes a good applicator for shoe soles.
Bulldog clips are handy to use for clamping straps and other small areas.
Pack includes a removable nozzle for easy application.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys SolarFlex
Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical.
Features
Superior weather protection
Long-lasting flexibility
No primer required before painting
Watertight seal with a 10-year guarantee*
Adhesion to wet or damp surfaces
Non-bubbling
Better curing and extrudability (>5°C) with no slump
Paintable with water-based paints after product skins in 60 to 90 minutes
Low VOC**
Where can this product be used?
Skylights
Walls
Patios
Floors
Fencing
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic tiles
Fibreglass
Most plastics*
*Not suitable on polyethylene, polypropylene, or Teflon.
Application Instructions
Ensure substrates are clean and free of oil, grease, or loose particles.
Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun.
Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint.
For neat joints, use masking tape on both sides of the joint and remove it before skinning.
Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information.
Limitations
Not suitable on polyethylene, polypropylene, or Teflon.
Cure excess product before disposal.
Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sole Grip is an easy-to-apply compound to repair and protect most shoe soles. Use it to coat the soles of shoes and protect from general wear and tear, extending the life of your shoes.
Features:
Easy to use
Long wearing
May be applied to both new and old shoe soles, as a repair or non-slip surface
Appearance
Dark brown tacky paste.
Where can this product be used?
Apply to new shoes to extend their sole life
Building up worn soles of shoes to extend their life
Creating an anti-slip surface on smooth soles of shoes
Creating an anti-slip surface on the bottom of furniture legs and castor holders
Creating an anti-slip base on fabric items such as dollies or placemats
Sole Fix is not an adhesive
May not adhere to some plastic/rubber soles
Will not bridge gaps where no backing exists
What materials is this product suitable for?
Leather
Rubber
Synthetic
Plastic
How to use this product
Roughen soles with the scraper provided.
Clean the surface with Selleys Solvent Acetone. Do not use Turpentine or Kerosene. (Note: Slow drying solvents such as Mineral Turps may interfere with adhesion).
Squeeze sufficient material for a thin layer about 1.5mm thick. Spread evenly over sole
Leave for 30 minutes before further applications. If required, apply 2 or 3 layers on average soles. On worn soles apply to suit.
Leave for 24 hours before wearing. Edges may be sandpapered or cut back and trimmed with a knife.
Handy tips
For best results, new shoes should be worn for several days before applying SoleGrip
Clean up excess with Mineral Turpentine prior to cure
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Avoid skin contact and avoid breathing vapours.
If eye contact occurs, flush eyes with water for 15 minutes. Obtain medical attention. If skin contact occurs, remove contaminated clothing and wash skin thoroughly with soap and water. If swallowed, DO NOT induce vomiting. Give a glass of water and seek medical advice. Intentional misuse by deliberately inhaling vapours of this product can be harmful or fatal.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Heavy Duty is a multi-purpose, tough and durable, light grey ready-mixed filler.
Features
Suitable for interior and exterior applications
Good adhesions to most surfaces
Water and weather resistant
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling holes, dents, cracks or chips in interior and exterior applications where no structural movement occurs
What materials is this product suitable for?
Mortar
Masonry
Concrete
Wood
Stone
Primed metal surfaces
Brick
Plaster
Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. For deeper cracks, apply in 6mm layers allowing each layer to dry before applying the next.
Lightly sand back any excess filler from the surface after product dries (2-3 hours for 2mm applications).
Dust off any loose dust before applying undercoat and painting with water-based paints or oil-based paints.
Limitations:
Product is not flexible so not suitable for use between surfaces that are subject to the structural movement - use Selleys No More Gaps.
Avoid using below 5°C or in wet conditions.
Painting with oil-based paints is not recommended until 24 hours after the filler has been applied.
Water-based paints may be used immediately after the filler has set.
If the filler is found to have stiffened prior to use, stir product. The product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed, lightweight filler designed for fast and easy repairs. It dries quickly, resists cracking and shrinking, and usually requires only one application—making it ideal for quick patching jobs around the home or office.
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use straight from the tub
Minimal shrinkage – no need to overfill
Fast drying – sand and paint within a short time
Includes a convenient filling spatula
Water-based formula – easy clean-up with water
Paintable with both oil-based and water-based paints
Where to Use
Cracks and holes on stable, non-moving surfaces
Walls, ceilings, doors, and window frames
Small repairs in plaster, timber, and masonry surfaces
Suitable Materials
Wallboard and plasterboard
Wood and timber surfaces
Masonry and plaster
Primed nail heads
Product Details
Colour: White
Technology: Water-based
Use: Interior, or exterior when painted
How to Use
Ensure surfaces are clean, dry, and free of dust or loose material.
Using the provided spatula, press filler firmly into the crack or hole and smooth the surface. No need to overfill.
Allow to dry (approximately 30 minutes for thin applications), then lightly sand for a smooth finish.
Remove dust and paint as desired. For oil-based paints, allow 24 hours before painting.
Limitations
Not suitable for use on plastic, metal, or exterior timber exposed to moisture.
Not flexible – avoid using between surfaces subject to structural movement (use Selleys No More Gaps Coloured Caulk 450g instead).
Not designed for load-bearing areas or surfaces under compression (e.g. behind doors).
Do not nail through filler. Avoid use below 5°C or in wet conditions.
Handy Tips
Wait 24 hours before painting with oil-based paints.
Water-based paints can be applied once the filler has set.
If filler thickens, stir before use. If too dry, add a small amount of water and mix.
Clean tools with water after use.
Before painting, clean with Selleys Sugar Soap Cleaner Concentrate 1L or Selleys Sugar Soap Wipes x25.
For outdoor applications, protect from rain until dry and painted with two coats.
Deeper repairs (over 2mm) may require longer drying times.
Recommended Accessories
For masking before painting: Bear Masking Tape Painter Edge Pro 48mm x 50m
For reinforcing plaster joints: Eazy Tape Plasterboard Joint Tape 90m
Clean Up
Remove uncured product with water.
Once cured, remove by scraping or sanding.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Rapid is a ready-mixed lightweight filler that is fast drying, virtually non-shrinking, non-cracking & needs only one application.
Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water-based, so can be cleaned up with water
Paintable with oil and water-based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Wallboard
Wood
Masonry
Plaster
Primed nail heads
Plasterboard
Colours White
Technology Water Based
Use Interior
Exterior (when painted)
How To Use
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product dries (30 minutes in thin applications).
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
Handy Tips
Painting with oil-based paints is not recommended until 24 hours after filler has been applied.
Water based paints may be used immediately after filler has set.
If filler is found to have stiffened prior to use, stir product. Product that has actually hardened should be discarded. If still too dry add one teaspoon of water and stir again to desired consistency.
Application tools may be cleaned with water.
Before painting, clean dust and filler particles using Selleys Sugar Soap or Selleys Super Kleen.
In exterior applications, protect from rain until dry and painted over with 2 coats of paint.
Some paints may temporarily discolour when applied over the filler, but will revert to the correct colour once dry.
For applications more than 2mm deep, or in cold or humid conditions, expect longer drying times.
Keep container closed when not in use.
Clean Up
Uncured product may be removed with water.
Cured product can be removed by scraping or sanding.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour.
Features
Easy to use. Can be applied by hand or with a putty knife
Product has exceptional keeping qualities
Available in a natural colour
Superior grade putty
Where can this putty be used?
A wood sash putty that is excellent for glazing wooden windows and doors
Bedding glass beads
Not recommended for use with heat absorbing glass
If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes
Not recommended for use where structural movement may occur
Not recommended for use in metal framed windows.
What materials is this putty suitable for?
Wood
Timber
How to use this product
Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing.
Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used.
Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass.
Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing.
Paint should be carried out 2mm above the top line of the putty.
Handy tips
Do not use kerosene, turps or other material to aid in working the putty
Allow putty to skin before applying paint
Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working
Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it.
Putty must be painted in exterior applications.
High humidity, cold weather and use in interior applications can extend skinning times.
Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil.
Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen.
Safety tips
Low hazard material
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Storm Waterproof Tape is a quick and easy way to seal and patch most objects*. It can be applied in the rain to stop leaks in an instant. Storm Waterproof Tape stops water leaks for 48 hours, making it ideal for emergency fixes until permanent repairs can be made.
Features
Waterproof & airtight seal* – Wet or Dry
Stops active water leaks for up to 48 hours*
Sticks to wet surfaces*
Removable
Suitable for interior and exterior
Suitable for fresh, salt & chlorinated water
Easy-to-use, DIY optimised format
Where can this product be used?
Can be used on gutters & flashing, down pipes, caravans, tents & tarps, rubber/plastic/vinyl pool liners, PVC piping, inflatable pool toys, small boats & kayaks air mattresses, umbrellas and more!
Suitable for Aluminium, Galvanised Steel, Colorbond® Steel, Copper, Brass, Fibreglass, some rubbers and plastics*
Ensure surface is free of dirt, grease and oil
Cut tape or patch to desired size. Ensure there is at least 2-3cm of tape extending beyond each edge of the hole
Remove backing paper, position carefully and press down firmly
Once in position, rub firmly to ensure no air or water bubbles are left under the tape, and ensure good contact between the tape and substrate
Leave tape until permanent repairs can be made
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces.
Features
Concentrated – makes up to 30 litres
Professional strength grease & grime cleaner
Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces.
Can be diluted with water or used neat
Where can this product be used?
Kitchen surfaces – to clean floors, walls and cupboards
Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces
Painting & Wallpapering – wash surfaces prior to painting
General Cleaning – appliances, stainless steel, blinds and more
What materials is this product suitable for?
Floors
Tiles
Walls
Benchtops
Cooktops
Appliances
Wipe off immediately from aluminium and brass surfaces
Handy tips
Dilute to suit the cleaning task.
Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose.
For smaller areas or spot, cleaning try Selleys Super Kleen
Safety tips
For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal.
Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes.
The use of rubber gloves is recommended
If swallowed, give a glass of water and see a doctor.
If in eyes, wash out immediately with water
For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The trusted cleaning performance of Selleys Original Sugar Soap is brought to you in a quick and easy-to-use format that is ideal for cleaning the walls and surfaces around your home.
Features
Large wipe: 200mm x 300mm
Strong interlaced cloth
Specifically designed for painted walls
Dual-sided: smooth side for surface wiping, textured side for deeper clean
Contains Selleys Original Sugar Soap
Everyday use
Where can this product be used?
Walls (especially painted walls)
Kitchen surfaces and appliances
Bathroom & laundry tiles, shower screens, basins, bathtubs & appliances
Directions
Open resealable lid.
Slowly peel back the resealable sticker.
Pull out wipe from pack.
For surface cleaning, use smooth side and simply wipe clean. For a deeper clean, use textured side and wipe up & down or in a circular motion.
Reseal the sticker and close the lid to keep remaining wipes fresh and ready for next use.
Dispose of used wipe in the rubbish bin.
Advice
Do not use on prints, signs, dial marks and clear plastics
Wipe off immediately from brass and painted surfaces
Excessive hard rubbing of low sheen or flat paints can result in glossy patches.
Test suitability in an inconspicuous area before using.
Safety Tips
Keep out of reach of children.
Avoid contact with eyes.
If in eyes, or if skin irritation occurs, rinse thoroughly with water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Why Choose Selleys Super Glue Adjustable Gel?
Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes.
Key Benefits:
Adjustable Setting Time: Allows precise alignment before setting.
Rapid Bonding: Bonds in 30 seconds for fast repairs.
Versatile: Adheres to ceramics, china, metal, wood, and most plastics.
Easy to Use: No mixing required, with a convenient gel formulation for clean application.
Where Can This Product Be Used?
Everyday household repairs on:
Ceramic and China
Metal and Wood
Most Plastics*
What Materials Is It Suitable For?
Bonds a variety of porous and non-porous surfaces.
Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers.
How to Use Selleys Super Glue Adjustable Gel
Prepare:
Pierce the seal by attaching the nozzle with the cap and turning clockwise.
Ensure surfaces are clean, dry, and free from dust, dirt, and grease.
Apply:
Apply a small amount of adhesive to the surfaces to be bonded.
Press surfaces together gently and hold for several minutes to ensure sufficient bond strength.
After Use:
Wipe the nozzle clean with a cloth or paper.
Replace the cap securely.
Limitations
Not suitable for use on leather, polyethylene, polypropylene, or PTFE.
Will not permanently bond vessels exposed to water or dishwashers.
Handy Tips for Best Results
Ideal for vertical applications and slightly porous materials.
Use 1 drop per cm² for optimal bonding.
Sets in 30 seconds, achieving maximum bond strength in 24 hours.
Clean-Up Instructions
Wipe the tip of the tube with a cloth or paper after use.
Replace the cap tightly to avoid drying out the product.
Product Details
Size: 1g Tube
Colour: Clear
Technology: Cyanoacrylate
Recommended Use: Interior
Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Why Choose Selleys Super Glue Adjustable Gel?
Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes.
Key Benefits:
Adjustable Setting Time: Allows precise alignment before setting.
Rapid Bonding: Bonds in 30 seconds for fast repairs.
Versatile: Adheres to ceramics, china, metal, wood, and most plastics.
Easy to Use: No mixing required, with a convenient gel formulation for clean application.
Where Can This Product Be Used?
Everyday household repairs on:
Ceramic and China
Metal and Wood
Most Plastics*
What Materials Is It Suitable For?
Bonds a variety of porous and non-porous surfaces.
Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers.
How to Use Selleys Super Glue Adjustable Gel
Prepare:
Pierce the seal by attaching the nozzle with the cap and turning clockwise.
Ensure surfaces are clean, dry, and free from dust, dirt, and grease.
Apply:
Apply a small amount of adhesive to the surfaces to be bonded.
Press surfaces together gently and hold for several minutes to ensure sufficient bond strength.
After Use:
Wipe the nozzle clean with a cloth or paper.
Replace the cap securely.
Limitations
Not suitable for use on leather, polyethylene, polypropylene, or PTFE.
Will not permanently bond vessels exposed to water or dishwashers.
Handy Tips for Best Results
Ideal for vertical applications and slightly porous materials.
Use 1 drop per cm² for optimal bonding.
Sets in 30 seconds, achieving maximum bond strength in 24 hours.
Clean-Up Instructions
Wipe the tip of the tube with a cloth or paper after use.
Replace the cap tightly to avoid drying out the product.
Product Details
Size: 3g Tube
Colour: Clear
Technology: Cyanoacrylate
Recommended Use: Interior
Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sil-X advanced polymer technology is formulated to deliver superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Sil-X has been specially developed to withstand the tough Australian and New Zealand conditions. Selleys THE ONE Adhesive delivers superior bond strength on any building surface. Can be applied to wet or dry, interior or exterior, porous or non porous surfaces*. Extreme versatility that takes the guess work out of DIY.
Features
Strong bond on any building material
Can be applied to wet or dry surfaces
Suitable for interior and exterior applications
Can be used on porous and non-porous materials
Will adhere to oily surfaces
Low VOC
Excellent weather resistance
Flexible and long lasting
Paintable with water-based paints
What materials is this product suitable for?
Suitable for all building materials*
How to use this product
Ensure surfaces are clean and free from grease or loose particles.
Cut tip of cartridge, fit nozzle and cut at 45ºangle to desired size before placing in a cartridge gun such as Selleys Light Speed Caulking Gun.
Apply with a caulking gun, pushing adhesive onto the surface.
Position pieces and press firmly together. Larger, heavier materials may need to be supported until the adhesive cures.
If painting, paint with water-based paint.
Handy tips
Keep a pack of SELLEYS Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
Limitations
*Not for PE, PP, PTFE, or permanent water immersion
Clean up
Clean up with turps before the adhesive cures.
Safety tips
Keep out of reach of children.
Avoid skin and eye contact and breathing vapours.
Use in a well ventilated area.
Wear protective clothing, gloves and eye protection.
If on skin, wash with soap and water.
Cure product before disposal.
Product releases methanol during cure.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Urethane Bond Is a high strength shock proof, water and chemical resistant polyurethane adhesive.
Features
High strength
Achieves maximum bond in 48 hours Shockproof
Flexible, shatterproof and impact resistant so it can take knocks Durable
Lasts a long time Chemical resistant
Wont break down by temporary exposure to most chemicals i.e. solvents Waterproof and weatherproof
Good for bonds exposed to the elements When curing, Urethane Bond expands, filling voids and strengthening the bond Easy to use
Requires no mixing, ready to use straight from the pack Only need to apply adhesive to one surface Versatile
Can be used inside or outside Sandable and paintable after dries
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort.
Key Features
Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements.
Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear.
Where to Use
Sportswear, such as ski parkas, gloves, etc.
Athletic shoes, including sandshoes and jogging shoes.
Camping gear, like tents and sleeping bags.
Cloth and canvas bags.
Umbrellas.
Outdoor furniture, e.g., canvas chairs.
Paper maps and plans.
Suitable for the Following Materials:
Fabric
Canvas
Nylon
How to Use
Preparation: Ensure that the item to be treated is clean and dry.
Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface.
Spray: Use a sweeping motion to spray until the surface is moist.
Dry: Allow approximately 3 hours for drying before using the item.
Limitations
Not suitable for leather or suede articles.
Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®.
Do not apply to areas that don't require protection (e.g., soles of shoes).
Handy Tips
Test for colorfastness in an inconspicuous area before full application.
Start spraying light-colored areas first, followed by darker areas.
Launder or dry-clean soiled articles as usual and reapply the Water Shield.
Specifications
Size: 200g Aerosol Can
Color: Colourless
Technology: Silicone-Based
Use: Suitable for both interior and exterior applications
Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout)
The product also contains fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away.
Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour so can be used in any environment without discomfort.
Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam.
Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch.
Temperature resistance – approximately -60°C +150°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
Where can this product be used?
Showers and sinks.
Metal, copper and brass fittings.
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper and brass fitiings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine.
Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine.
Avoid smearing on surrounding surfaces, see handy tip.
Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal.
Handy tips
Tips for Using a Silicone Sealant in a Wet Area
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish complete painting prior to use of the sealant as it can not be painted over.
For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas
Key Features
Matt finish for elegant look
100% silicone sealant
25-year guarantee against cracking or peeling
Waterproof seal with superior adhesion
Mould-resistant formula
Non-corrosive, neutral cure
Best For
Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures.
Suitable Materials
Ceramic, Glazed & Porcelain Fixtures
Metal, Copper & Brass Fittings
Plastic Laminates
Rubber
Glass
Stainless Steel
Concrete & Grouts
Many Plastics including Polystyrene
How to Use
Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application.
Limitations
Not paintable
Not suitable for certain materials and uses
Handy Tips
Mask sides for neater joints. Work in manageable sections for a smoother finish.
Clean Up
Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
Additional Info
Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens.
Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
Mould resistant
Precision application for the best finish
Where can this product be used?
Showers
Baths
Spas
Sinks
Metal, copper and brass plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Powder coated aluminium
Aluminium
Plastic laminates
Rubber
Glass
Stainless steel
Concrete
Size
100g Aerosol can
Technology
Neutral Cure Silicone
Use
Interior
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
1. Throughly clean and dry surface from oil, dirt and grease with mineral turps.
2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
4. Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Sealant is not paintable.Complete painting 7days prior to applying sealant.
• Not for aquariums or contact with food, eating utensils or drinking water.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens.
Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
Mould resistant
Precision application for the best finish
Where can this product be used?
Showers
Baths
Spas
Sinks
Metal, copper and brass plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Powder coated aluminium
Aluminium
Plastic laminates
Rubber
Glass
Stainless steel
Concrete
Size
100g Aerosol can
Technology
Neutral Cure Silicone
Use
Interior
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
1. Throughly clean and dry surface from oil, dirt and grease with mineral turps.
2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
4. Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Sealant is not paintable.Complete painting 7days prior to applying sealant.
• Not for aquariums or contact with food, eating utensils or drinking water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
High-Grade Neutral Cure Silicone
A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots.
Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying.
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour, so can be used in any environment without discomfort.
Easy to clean once applied, as it resists moisture, hot cooking oils, and steam.
Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch.
Temperature resistance: approximately -60°C to +150°C.
25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying.
Where can this product be used?
Showers and sinks
Metal, copper, and brass fittings
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper, and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine.
Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe.
Remove tape before the sealant skins. Clean tools immediately with mineral turpentine.
Avoid smearing on surrounding surfaces.
The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup.
When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish, complete painting prior to using the sealant as it cannot be painted over.
Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish.
Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures.
Safety Tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and Re-Use
Store in cool dry conditions, below 30°C.
The sealant should be used within 6 months after opening.
After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity.
For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge.
If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Silicone is a high-quality, neutral cure silicone sealant designed specifically for areas exposed to moisture, such as kitchens, bathrooms, and laundries. This 100% silicone formula provides a long-lasting waterproof seal that won’t shrink, crack, or peel for up to 25 years, making it ideal for sealing around showers, sinks, bathtubs, and other wet areas. Its anti-mould properties ensure that your bathroom stays hygienic and clean for longer.
The 90ml tube is perfect for smaller jobs or touch-ups, offering easy handling for precise application in tight spaces. Selleys Wet Area Silicone adheres to a wide range of materials, including ceramics, glass, stainless steel, metal fittings, and plastic laminates, ensuring a secure, flexible seal in high-humidity environments. Whether you’re sealing around a kitchen sink or maintaining the edges of a shower enclosure, this product guarantees professional results every time.
Where can this product be used?
Showers screens
Baths
Spas
Sinks
Plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Clean surface with mineral turpentine and dry.
Cut cartridge, fit and cut nozzle at 45° angle and fit into a caulking gun.
Apply with steady pressure, ensuring sealant is pushed into joint.
Tool with a spatula dipped in detergent water within 5-10 mins of application.
Clean up with mineral turpentine before product skins.
Sealant will cure in 72hrs.
Limitations:
Not paintable. Complete painting 7 days prior to applying sealant.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
Not suitable for aquariums.
Not suitable for food or drinking water contact.
Not suitable for permanent water immersion.
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Work in sections that can be completed before sealant skins.
Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish.
*Warranty Information
Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean Up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by
cutting and scraping.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
High-Grade Neutral Cure Silicone
A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance.
Features
Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots.
Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying.
Built-in fungicide to inhibit the growth of mould.
Available in a range of colours to suit most wet areas.
Non-corrosive neutral cure formula.
Low odour, so can be used in any environment without discomfort.
Easy to clean once applied, as it resists moisture, hot cooking oils, and steam.
Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch.
Temperature resistance: approximately -60°C to +150°C.
25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying.
Where can this product be used?
Showers and sinks
Metal, copper, and brass fittings
Perfect for use on or around:
Showers
Baths
Spas
Sinks
Plumbing Fixtures
Can not be painted over.
Not suitable for building materials that bleed oils or solvents, such as impregnated wood.
Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Ceramic, glazed & porcelain fixtures
Metal, copper, and brass fittings
Plastic laminates
Rubber
Glass
Stainless steel
Concrete and grouts
Many plastics including polystyrene
How to use this product
Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy.
We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface.
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge.
Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing.
Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action.
For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine.
Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe.
Remove tape before the sealant skins. Clean tools immediately with mineral turpentine.
Avoid smearing on surrounding surfaces.
The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal.
Handy Tips
Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup.
When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
Remove the tape before the silicone sealant skins.
For a better finish, complete painting prior to using the sealant as it cannot be painted over.
Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish.
Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures.
Safety Tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well-ventilated area as the product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and Re-Use
Store in cool dry conditions, below 30°C.
The sealant should be used within 6 months after opening.
After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity.
For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge.
If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*.
Provides superior water resistance, mould and soap scum resistance
White For Life – Always looks like new*
Resists yellowing, staining and blackening*
Crack resistant
Sand free - resists scratching files
Suitable for indoor wall and floor tiles
Comes in a cartridge for minimum wastage
Where can this product be used?
Bathrooms
Showers (walls only)
Toilets
Laundries
Kitchens
What materials is this product suitable for?
Ceramic tiles
Porcelain tiles
Stone tiles
Most other tiles
Please contact your store to confirm avaliability, as some stores may have a limited range.
How to Use
Preparation
For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult.
Application
Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time.
Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint.
Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets.
Allow grout to firm up in joints for approx 20 min (longer in colder conditions).
Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints.
Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks.
overage
1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
Limitations:
Not for areas frequently immersed in water eg. Shower floors.
Allow to dry for 3 days before exposing grout to water on shower walls.
Handy tips
If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas.
*To maintain whiteness and long term stain & mould resistance:
Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard.
Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners.
Areas subject to high foot traffic will require frequent cleaning.
Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes.
Coverage guide
1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
Clean Up
Clean up tools with water before product hardens.
Uncured product may be removed with water.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a premium-quality, pre-mixed grout designed to deliver a brilliant, long-lasting white finish for wall and floor tiles. Suitable for interior applications with joints up to 5mm, this product is ideal for both new tile installations and regrouting jobs.
Surface Preparation:
Ensure all surfaces are clean, dry, and free from dust, oil, old grout, and other contaminants.
For new tiling jobs, let tile adhesive set for at least 24 hours.
For regrouting, completely remove old grout and thoroughly clean the joints.
Application Instructions:
Cut the cartridge tip and attach the nozzle. Trim to desired bead width.
Using a caulking gun, apply grout into joints, pressing it in to eliminate air gaps.
Smooth grout using a rubber float or grout applicator, working diagonally.
After 15–20 minutes (depending on temperature), gently wipe tile surfaces with a damp sponge to remove excess grout and haze.
Avoid over-wetting and excessive wiping, which can weaken the grout lines.
After 24 hours, polish tile surfaces with a soft dry cloth to remove any remaining haze.
Coverage:
Approx. 2m² per 410g cartridge (based on 300x300mm tiles with 3mm x 5mm joints)
Drying Time:
Touch dry in 30 minutes
Allow 72 hours before exposing to water in wet areas such as showers
Clean-Up:
Clean tools and tile surfaces with water before the grout cures
Once dry, remove excess grout by mechanical means
Technical Data:
Colour: White
Appearance: Smooth, creamy paste
Joint Width: Up to 5mm
Water Clean-Up: Yes (before curing)
Shelf Life: 12 months if stored unopened in a cool, dry place
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives.
Surface Preparation:
Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility.
Application Instructions:
Twist the nozzle to spray position.
Spray directly onto the surface.
Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up.
Wipe using a damp sponge or cloth.
Rinse thoroughly with clean water.
For a streak-free finish on glass and taps, dry with paper towel before the surface dries.
Coverage:
Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom.
Drying Time:
Fast-drying; ensure complete rinsing and wiping for optimal results.
Clean Up:
Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces.
Technical Data:
Form: Liquid
Colour: Pale Yellow
Scent: Fresh Lime
Use: Interior (kitchens, bathrooms, showers)
Packaging: 750mL trigger spray bottle
![Selleys No Mould Silicone Selant 100ml [White]](//gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](//gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](//gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](//gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](//gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
![Selleys Wet Area Sealant EZI Press [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
![Selleys Wet Area Sealant EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](//gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
![Selleys No Mould Silicone Selant 100ml [White]](http://gluesaustralia.com.au/cdn/shop/files/15eb0d3681e54148ad88ef00e07df55b.png?v=1757753027&width=645)
![Selleys Roof & Gutter Silicone Sealant UV & Weather Resistant 310g [Black]](http://gluesaustralia.com.au/cdn/shop/files/2330c4b4af69418ba74ba7691a5becd0.jpg?v=1757756157&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
![Selleys Storm Sealant [Grey] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/3fd79b6c48214ee189a4b5f9796ebfdd.png?v=1757752927&width=645)
![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
![Selleys Wet Area Sealant EZI Press [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys Wet Area Silicone Sealant Kitchen Bathroom & Laundry 300g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/add6c9293f9448a0b56570405080097d.jpg?v=1757756088&width=645)
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
