![Selleys Wet Area Bathroom & Kitchen Sealant 90ml [Clear]](http://gluesaustralia.com.au/cdn/shop/files/c6f19281f9004498803c7384706ed1c6.jpg?v=1757752906&width=645)
A high grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (eg. grout) The product also contains fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould and fungus will not become trapped in the silicone, therefore keeping those unslightly black mould spots away. Superior silicone formulation forms a durable seal which locks out water and which does not shrink when drying Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour so can be used in any environment without discomfort. Is easy to clean once it is applied, as it resists moisture, hot cooking oils and steam. Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. Temperature resistance – approximately -60°C +150°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Where can this product be used? Showers and sinks. Metal, copper and brass fittings. Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper and brass fitiings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Throughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow to dry completely before applying silicone. If there old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenous product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course grain, as the silicone will adhere more readily to a scratched up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point any unwanted sealant can be removed by trimming with a sharp blade, but avoid under cutting the seal. Handy tips Tips for Using a Silicone Sealant in a Wet Area Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface, may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$11.00
Introducing Selleys Water Shield, your go-to solution for making your fabrics water, snow, and ice-repellent without compromising comfort and breathability. Ideal for active individuals and outdoor enthusiasts, this product is designed to keep you dry while ensuring maximum comfort. Key Features Water, Snow, and Ice Repellent: Provides an effective barrier against moisture and cold elements. Breathable: Does not impair the comfort and breathability of the material, making it ideal for sportswear. Where to Use Sportswear, such as ski parkas, gloves, etc. Athletic shoes, including sandshoes and jogging shoes. Camping gear, like tents and sleeping bags. Cloth and canvas bags. Umbrellas. Outdoor furniture, e.g., canvas chairs. Paper maps and plans. Suitable for the Following Materials: Fabric Canvas Nylon How to Use Preparation: Ensure that the item to be treated is clean and dry. Application: Hold the aerosol can upright, approximately 100-150mm (4-6 inches) away from the surface. Spray: Use a sweeping motion to spray until the surface is moist. Dry: Allow approximately 3 hours for drying before using the item. Limitations Not suitable for leather or suede articles. Avoid use on fabric already treated with water repellents like DRW or waterproof materials like Gore-tex® or Driza-bone®. Do not apply to areas that don't require protection (e.g., soles of shoes). Handy Tips Test for colorfastness in an inconspicuous area before full application. Start spraying light-colored areas first, followed by darker areas. Launder or dry-clean soiled articles as usual and reapply the Water Shield. Specifications Size: 200g Aerosol Can Color: Colourless Technology: Silicone-Based Use: Suitable for both interior and exterior applications Keep your gear and clothing dry and comfortable. Experience the protection and convenience of Selleys Water Shield today!
$21.00
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 1g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$9.59
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
A strong, weather and impact resistant adhesive that is ideal for most shoe repairs. Features Easy to use Strong Flexible Bond Weather resistant Impact resistant Appearance Dries yellowish/beige Where can this product be used? Sole Tongue Strap Inner sole Attach beads, jewels, decorative items Will not bond Polyethylene or Polypropylene plastics. For these we recommend Selleys Plastics Glue. May not adhere to some plastic / rubber soles. What materials is this product suitable for? Leather Canvas Fabric Rubber Cork Most Plastics EVA foam (e.g Desert boots sole) How to use this product Ensure surfaces are clean, dry and free from dirt or grease. Remove cap and carefully pierce seal. For larger area repairs such as shoe soles, we recommend you use the contact bond method: For quick and even bonding, apply to one surface only, press together and pull apart. Keep apart until the adhesive film is almost dry (approx. 10 – 20 minutes). Carefully line up surfaces to be joined and press surfaces firmly together. Bonds immediately on contact. Clamping may be necessary in some applications. For smaller areas, either use the contact method as above, or join with a wet bond: Apply Shoe Glue to one surface only and immediately press together. Lightly clamp or hold until dry. Allow adhesive to achieve maximum bond strength (24 hours) before wearing your repaired shoe/s. Wipe nozzle clean and replace cap immediately after use. Clean up application tools and excess adhesive with turps before it dries. Handy tips A piece of plastic from a takeaway container makes a good applicator for shoe soles. Bulldog clips are handy to use for clamping straps and other small areas. Pack includes a removable nozzle for easy application.
$6.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$18.00
Key Features UV and weather resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non corrosive neutral cure formula Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters. Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND How to Use Use in a well ventilated area. Avoid contact with skin and eyes. Thoroughly clean and dry surface from oil, dirt and grease with mineral turps. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun. Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps. Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal. Limitation: • Not paintable. Complete painting 7 days prior to applying sealant. • Not recommended for use as a plug for burst pipes. • Do not use in below waterline applications. ^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use Handy tips For neater joints, mask sides before applying sealant and remove tape before sealant skins. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy. *Warranty Information * Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010. Clean up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
$12.00
Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula. Has superior flexibility +/- 25% movement capability Temperature resistance - approximately -60°C +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25 year guarantee* against crumbling, cracking and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm2/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
$13.90
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$5.00
A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS. Features Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS Shock resistant, giving you a longer-lasting fix Fast setting in 30 seconds Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper *Does not work on PTFE (Teflon) Where can this product be used? To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control What materials is this product suitable for? ALL plastics* including polyethylene, polypropylene and ABS Metals Timber China Rubber Leather Paper How to Use Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface. Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise. Remove cap and apply a small amount of glue to one surface only. Limitations: Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam. Product only works on some rubbers and will not work on PTFE. May cause leather to harden or discolour, test on an inconspicuous area first.
$10.29
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$13.00
Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$21.00
Liquid Nails Clear eliminates unsightly mess caused by conventional brown construction adhesives because it dries clear and blends with the surrounding surface. It is ideal where a fine finish is important. Uses Selleys Liquid Nails Clear is suitable for bonding to glass, fibreglass, metals, most plastics*, timber, particleboard, MDF, tiles & ceramics, concrete, painted and masonry substrates. Suitable for bonding mouldings & trims, skirting boards & architraves, general fabrication and creating mosaics. Pre-test plastics to determine compatibility. Technical Features High performance solvent based adhesive. Note: When use on glass to glass, thin film application is recommended for better clarity. Good paintability – Paintable with water based paints. Oil based paints require undercoating with water based paints first. Excellent resistance to water and weather makes it suitable for interior and exterior applications. Application Tips Due to solvent content Liquid Nails Clear should not be used in enclosed space or without ventilation Solvents may affect some plastics Will not bond polyolefin plastics such as polyethylene and polypropylene May damage some polycarbonate, avoid smears and spills Cannot be used on polystyrene foam May not adhere to wet absorbent surfaces or to some old wet metals In very cold weather cartridge must be conditioned to room temperature before use Not recommended for permanent water immersion or water containment structures Must be first painted with water based paint prior to painting with oil based paints Will not accept common wood stains. (If staining is required, it is recommended to stain timber before bonding). Full cure in 2 weeks Not recommended for mirrors Bonds weaken at high temperatures. Avoid bonding metals or heavy materials which will be heated by direct sun. (Consult Selleys about particular applications subject to heating). Ensure that surfaces are free from dust, loose particles and dry. Cut cartridge tip, pierce membrane inside base of nub, fit nozzle and cut end to desired opening and fit cartridge into cartridge gun. In very cold weather, cartridge may need to be conditioned to room temperature for easier gunning. Direct a bead along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. (“zig-zag” beads are more appropriate on surfaces of moderate width) Fix with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. Wet bonds are re-positionable for up to 20 mins after fitting Allow adhesives to set (at least 24 – 48 hours) before removing any temporary fasteners or clamping. (refer to Bond strength Time) For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-3 minutes before firmly Technical Details and Performance Time for strong bond depends on nature and condition of application. A minimum of 24 to 48 hours is needed for sufficient strength to develop. The bond will continue to strengthen over time. Full cure up to 14 days. Curing is achieved by evaporation of solvent. Time to achieve full strength is increased: at constant low temperatures; when thick applications (joints) are used; wide areas are bonded; when bonded surfaces are impervious (e.g. metals and glass). Indicative information only, not to be used for setting specifications. Appearance Clear soft adhesive Viscosity 5000 – 9000P TE/2 @ 25oC HAF/HELIPATH Skin Time / Tack Free Time 5 min. @ 25oC Specific Gravity 0.87g/mL Extrudability 100g/min. @ 25oC (at 628kPa pressure through 3mm orifice) Solid Content 60% Cure By evaporation of solvent Water Based Paints Good Alkyd Paints Good, after first undercoating with a water based paint Flammability Uncured adhesive- flammable Cured adhesive – will burn if ignited Service Temperature Maximum 80oC Coverage 15 metres of a 5mm diameter bead Cleaning Clean off wet adhesive with mineral turps or white spirit. Dry adhesive can be removed by scraping or sanding.
$16.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before the adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High-Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many kinds of wood. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be softened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$6.00
Selleys 655 FC Crystal Clear Flexible Adhesive and Sealant 290 mL Premium 100 percent crystal clear hybrid adhesive and sealant that delivers superior strength, instant grab, and long lasting flexibility. Bonds and seals on most common building materials, works indoors and outdoors, and can be applied to wet or damp surfaces. Low VOC, non yellowing, paintable, and non slumping for neat vertical and overhead joints up to 20 mm. Why you will love it Superior strength with instant grab Primerless adhesion on most surfaces Applies to wet or damp substrates Fast curing with non slumping finish Crystal clear appearance that stays clear Low VOC and isocyanate free Paintable with water based paints Suitable for interior and exterior use Where it works Ideal for sealing, bonding, and filling on concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, fiberglass, and most plastics. Not recommended for polyethylene, polypropylene, or PTFE. Typical applications Clear sealing of kitchen and laundry splashbacks Bonding trims, panels, and skirtings Sealing gaps in windows, door frames, and cladding General construction and maintenance sealing where a clear finish is desired How to use Prepare the surface so it is clean and free from dust, grease, and loose material. Cut cartridge tip, attach nozzle, and load into a caulking gun. Cut nozzle to the required bead size. Apply a continuous bead, pressing firmly so the product contacts both sides of the joint. Tool with a soapy solution before skinning. For neat edges, mask before applying and remove tape before skin forms. Clean up Uncured product cleans off with mineral turps. Once cured, remove by scraping or sanding. A dedicated silicone and adhesive remover can assist. Good to know Do not paint with solvent based paints. If painting, first coat with a water based paint. Not suitable for permanent water immersion or below water line use. Store below 30°C. Use within 6 months after opening for best results. Specifications Technology Moisture curing silyl modified polymer Colour Clear Pack size 290 mL cartridge Density Approx. 1.06 g/mL Application temperature 5 to 35°C Tooling time at 23°C and 50 percent RH About 25 minutes Skin time at 23°C and 50 percent RH About 45 to 55 minutes Cure rate at 23°C and 50 percent RH Approx. 3 mm per 24 hours Slump 0 mm Tensile strength About 1 MPa Shore A hardness 30 ± 5 Elongation at break Approx. 130 percent Modulus at 100 percent elongation About 1.0 MPa Service temperature 0 to 70°C VOC content Approx. 35 g/L Safety Follow good ventilation and hygiene practices. Refer to the product safety data sheet for detailed advice.
$20.00
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$24.00
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$14.24
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$15.74
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$68.31
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$8.12
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
Parfix super glue is a fast setting cyanoacrylate-based adhesive that dries clear with a strong bond Instant strong bond Sets in 10 seconds Dries clear
$2.59
![Parfix Roof Gutter Concrete Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115744_c50eb875-361a-40d9-9352-04fade1d8d60.jpg?v=1754712244&width=645)
Can be used on both interior and exterior substrates Highly flexible Non-corrosive Neutral cure Parfix Roof, Gutter And Concrete Silicone is a clear, highly flexible, neutral cure sealant designed for both interior and exterior use. Ideal for use on galvanised iron, concrete and roofing, Parfix Roof, Gutter And Concrete is specially formulated to remain flexible under harsh weather conditions.
$11.49
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$14.76
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$7.86
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.03
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive
$11.39
This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth Directions: Ensure all surfaces are clean, dry and free of oil, grease and wax Shake well before use Only apply to one surface Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions) Remove excess glue with a damp cloth Great strength is achieved when dried overnight Cleaning: Clean up with water. Wash hands after use
$44.11
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$7.22
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution Product Overview Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium. Key Features & Benefits Quick exposure to light running water UV resistant for lasting outdoor use Neutral cure, making it versatile and safe for different materials Non-corrosive and AS 4020 approved Compatible with Monarch Mini Compact Caulking Gun Perfect For Great for small projects where a full-size cartridge is not needed. Ideal for: Repairing gutters Fixing roofs Mending downpipes Tight spaces that traditional cartridges can't reach Colors Available Available in black and translucent versions for versatility in your projects. How To Use Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
$7.35
Loctite Super Glue Longneck Bottle features a precision tip which allows controlled application without dripping, thus less mess. It has an easy-open cap with a metal pin that cleans and seals the nozzle for a clog-free performance. The long nozzle is ideal for gluing hard to reach surfaces. The ''finger friendly'' bottle keeps fingers glue free, as well as allows for a continuous flow or a precise drop of glue. It bonds a variety of materials including leather, ceramic, rubber, paper, metal, china, wood and most plastics. Loctite Super Glue Longneck Bottle dries clear and sets without clamping. Loctite Super Glue Longneck Bottle is resistant to moisture, most chemicals and freezing temperatures. Recommended For Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings Not Recommended For Use in dishwasher, oven or microwave Use on repairs needing high flexibility Glazed surfaces Exterior Applications Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene Safety Precautions Apply in a well-ventilated area. Wear gloves and wash hands after use. Preparation Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup Cured adhesive may be cut away with caution using a sharp blade, acetone or with boiling water.
$8.44
Loctite Super Glue Longneck Bottle features a precision tip which allows controlled application without dripping, thus less mess. It has an easy-open cap with a metal pin that cleans and seals the nozzle for a clog-free performance. The long nozzle is ideal for gluing hard to reach surfaces. The ''finger friendly'' bottle keeps fingers glue free, as well as allows for a continuous flow or a precise drop of glue. It bonds a variety of materials including leather, ceramic, rubber, paper, metal, china, wood and most plastics. Loctite Super Glue Longneck Bottle dries clear and sets without clamping. Loctite Super Glue Longneck Bottle is resistant to moisture, most chemicals and freezing temperatures. Recommended For Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass™, polycarbonate, polystyrene and PVC Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings Not Recommended For Use in dishwasher, oven or microwave Use on repairs needing high flexibility Glazed surfaces Exterior Applications Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene Safety Precautions Apply in a well-ventilated area. Wear gloves and wash hands after use. Preparation Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup Cured adhesive may be cut away with caution using a sharp blade, acetone or with boiling water.
$8.44
Instant, crystal clear bonds that are water and dishwasher-resistant. Formulated to work on all types of glass. Recommended on: Glass, Crystal, Tinted Glass, Glass Works, Opaque Glass, Blown Glass. Properties: Bonds glass to glass Glass to metal Stained glass Crystal and tinted glass Water and dishwasher resistant Bonds in seconds Dries transparent for invisible bonds Easy to open, self-piercing and anti-clog cap Solvent-free Step by Step: Ensure surfaces to be joined are clean, completely dry and close fitting Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set Replace the cap immediately and store upright in a cool dry place. How to Repair a Glass Water Jug? Loctite Super Glue Glass has been specially formulated to repair glassware, delivering a sparkling performance every time. Once dry it forms crystal clear bonds on all types of glass breakages and cracks, delivering water and dishwasher resistant seals that are not only neat and free from unsightly white glue marks but also strong enough to resist pressure from temperature changes and water. Loctite Super Glue Glass is designed to work on all kinds of glass: glass, crystal, tinted glass, glass works, opaque glass and blown glass, and has a high strength formula that ensures you get long-lasting durability. Follow the step by step application guide: 1.Wash the broken area with water (avoid using detergent as this can affect the glue's performance) and dry thoroughly. Ensure that the surfaces to be joined are close fitting. 2.Carefully squeeze a small drop onto one of the broken parts. Press both surfaces together firmly and wait until they is set. 3.Do not move until the surfaces are set. Don’t worry if there is some excess glue, this can be easily removed once dry (see point 5) 4.Allow at least 1-2 hours to fully cure before using. For best results leave overnight. 5.Once dry, if there is any excess residue, gently wipe with a tissue dipped in Loctite Glue Remover or nail varnish remover containing acetone. 6.Replace the cap immediately and store the glue upright in a cool dry place.
$8.28
Loctite's versatile and reliable Super Glue Liquid is fast and strong and has a range of applicators that will get the job done quickly in every situation. It dries transparent to form a long-lasting invisible bond in seconds. Now with a NEW formula, resisting to all conditions: *Water and dishwashing *Shock *Temperatures from -50°C up to 120°C Recommended on: China, Porcelain, Metal, Rubber, Leather, Wood, Plastic (except PE/PP), Paper. Properties: Multi-use liquid superglue, ideal on non-porous surfaces Water and dishwasher resistant Shock resistant Temperature resistant (from -50°C up to 120°C) Bonds in seconds Withstands heavy loads Dries transparent Easy to open, self-piercing and anti-clog cap Choice of applicators - anti-spill / easy grip / long nozzle / brush-on Suitable for use on most surfaces* Solvent-free *Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$16.00
When you have a minute - tackle even big repairs with the new Loctite 60 seconds All-Purpose Glue. It is fast, strong and repositionable. Perfect results in only 60 seconds. Recommended on: Leather, Rubber, Wood, Metal, Porcelain, Paper, Plastic*. Properties: -Fast: it bonds materials within ca. 60 seconds -Extra strong: it builds up a strength of 100+ kg/cm² within a short time -Repositionable: it gives time to reposition the parts that you want to glue -Ideal for all home repairs, even mid-size and large surfaces -Non-drip gel formula, suitable for vertical applications -It dries transparent -Suitable for use on most surfaces* -Solvent-free -Perfectly bonds non-porous to non-porous materials *Except polyethylene (PE), polypropylene (PP), PTFE, glass, Styropor® and synthetic fibres Step by Step: 1.Ensure surfaces to be bonded are clean, completely dry and close-fitting. 2.Twist the cap/nozzle clockwise onto the tube and remove the cap. 3.Carefully apply the glue on one surface. Press the surfaces together, reposition it as you wish, then press with strong and even pressure for few seconds and leave it undisturbed for 60 seconds. 4.Clean the nozzle, replace the cap and store upright in a cool dry place.
$20.45
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$22.51
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$9.53
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. Clamp Time: 10-30 Seconds // Open Time: Not Repositionable Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent Full Cure: 24 Hours DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Apply Gorilla Super Glue Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch. Secure Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
$14.99
Gorilla Spray Adhesive is heavy duty, multi-purpose and easy to use. Gorilla Spray Adhesive forms a clear, permanent bond that is moisture resistant and can be used on projects both indoors and out. This spray adhesive is also photo safe. Its wide pad nozzle and controlled, fine mist spray provide an even application on the project you are working on. PRODUCT FEATURES HEAVY DUTY: Dries Permanent EASY TO USE: Repositionable CLEAR COLOR: Non-Yellowing* INDOOR & OUTDOOR: Moisture Resistant CONTROLLED SPRAY: Even Application WIDE PAD NOZZLE PHOTO SAFE All surfaces should be clean and free of dirt, grease and oil. Protect surrounding areas from overspray to avoid residual adhesive. Shake can well before using. Hold the can 15 to 20cm from surfaces to be bonded and spray an even coat of adhesive. For Maximum Bond Strength: Spray both surface to be joined. Allow to dry to tack (approximately 1 minute) and press surfaces firmly together. For Repositionable Bonds: Spray a light even coat on one surface. Allow to dry 1-3 minutes before joining. Repositionable up to 10 minutes depending on surface type, then bond becomes permanent. To remove, gently peel from corner. Tip: To avoid possible clogging, turn can away from body, turn upside down and spray a short jet of clear gas after completing the job. *Not recommended for use on vinyl materials, automotive headliners, polypropylene, polyethylene or similar materials. Do not use for bonding weighted materials. APPLICATION TEMPERATURE – 10°C to 32.2°C OUTDOOR – Yes MOISTURE RESISTANT – Yes PAINTABLE –Yes SANDABLE – Yes STAINABLE – No CURED COLOR – Clear PHOTO SAFE – Yes How do I remove Gorilla Spray Adhesive from my surface? To clean surface while adhesive is still wet/uncured, wipe adhesive off the project with a dry cloth. Isopropyl alcohol (IPA) may be used according to manufacturer’s instructions. Once cured, Gorilla Spray Adhesive may be removed using mechanical means by gently scraping surface, being careful not to damage the surface underneath. How do I remove Gorilla Spray Adhesive from body/skin? While still wet, Gorilla Spray Adhesive can be removed by wiping adhesive with a dry cloth, and then washing the area with soap and water. Once cured, rinse well with water. Is Gorilla Spray Adhesive food safe? Gorilla Spray Adhesive is not recommended for direct or indirect food contact and should not be considered food safe. What surfaces will Gorilla Spray Adhesive bond to? Gorilla Spray Adhesive is a multi-purpose product that will bond a wide variety of surfaces including fabric, paper, wood, plastic*, cardboard, foam, metal and more! NOTE: Not recommended for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content. Not for use on food contact surfaces. Will Gorilla Spray Adhesive bond vinyl/acrylic/rubber? Gorilla Spray Adhesive will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content.
$29.95
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, and holds up to 6.8kg! (15 pounds) Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features 6.8KG Strong Hold - Sticks to smooth and rough surfaces.* Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How much weight will Gorilla Mounting Tape hold? Gorilla Black Mounting Tape will hold up to 30 (13.6KG) pounds per project. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$17.95
Gorilla Clear Grip® is a flexible, fast-setting, crystal clear contact adhesive that creates a strong, permanent bond. Gorilla Clear Grip® is paintable and waterproof making it great for projects both inside and out! Build, Repair, Craft™ PRODUCT FEATURES WATERPROOF – For indoor/outdoor use FAST GRAB – Holds in just seconds PERMANENT BOND FLEXIBLE CRYSTAL CLEAR HEAVY DUTY NO-RUN FORMULA PAINTABLE PHOTO SAFE WASHER & DRYER SAFE BONDS: Metal, Glass, Fabric, Wood, Ceramic, Leather, Paper, Plastic*, and More! *Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. All surfaces should be clean and free of dirt, grease and oil. Best if used between 10°C and 32.2°C. Clear Grip® should only be used in a well ventilated area. Apply adhesive to each surface to be bonded. To maximize bond strength: Wait approximately two minutes for adhesive to partially dry before joining surfaces. Press surfaces firmly together. NOTE: Bond forms immediately and can be difficult to reposition. Cure Time Allow for a minimum of 24 hours for full cure. Cure time may increase with lower temperatures and when used on non-porous surfaces. Storage Tips After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. Store away from children and animals. Clean-up Wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. Paintable When fully cured. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. TECHNICAL SPECS APPLICATION TEMPERATURE – 10° to 32.2° C, best at room temperature OUTDOOR – Yes MOISTURE RESISTANT – Waterproof PAINTABLE – Yes – Can be painted with water and oil based paints, spray paint SANDABLE – Yes STAINABLE – Yes CURED COLOR – Clear STORAGE TIPS – Flammable adhesive, do not use or store near heat, sparks, flames, or while smoking. Store in a cool, dry location. Wipe nozzle clean before replacing cap, for easy re-open apply a thin coat of petroleum jelly to threads. GAP FILLING – No PHOTO SAFE – Yes WASHER & DRYER SAFE – Yes How should Gorilla Clear Grip® be stored? After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing cap. What surfaces does Clear Grip® adhere to? Gorilla Clear Grip® can be adhered to many surfaces including: Wood, Metal, Stone, Ceramic, Glass, Plastic*, PVC, Brick, Concrete, Foam, Paper, Rubber, Fabric, and Laminate. *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. Is Gorilla Clear Grip® food safe? Clear Grip® should not be used around food. How do you clean up Gorilla Clear Grip®? When using Clear Grip®, it is best to wear safety glasses and chemical resistant gloves. To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. See first aid treatment for skin contact. Is Gorilla Clear Grip® gap filling? No Is Gorilla Clear Grip® UV Resistant? Yes Can Gorilla Clear Grip® be used both indoors and outdoors? Yes, Gorilla Clear Grip® can be used both indoors and outdoors. Is Gorilla Clear Grip® stainable? Yes, Gorilla Clear Grip® is stainable when fully cured. Is Gorilla Clear Grip® sandable? Yes, cured Gorilla Clear Grip® is sandable. Is Gorilla Clear Grip® paintable? Yes, when fully cured. Is Gorilla Clear Grip® Washer/Dryer safe? Yes Is Gorilla Clear Grip® photo safe? Gorilla Clear Grip® is safe to use with photos.
$15.72
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$12.90
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless. Features: Dries Clear: Ideal for clean, easy finishing 5 Minute Set: Plenty of repositioning time for the perfect fit. Gap-Filling: Fills voids and bonds uneven and vertical surfaces. Water Resistant: Withstands moderate exposure to water Solvent resistant Non-Toxic once cured Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses. Directions Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Prepare Your Work Area and the Surface If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together. Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded. Mixing Gorilla Epoxy Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio. Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine. Application After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply. Clamping To reach maximum bond strength, clamp project together and leave undisturbed. Important Cure Times Set: 5 minutes to apply and position Handling: Allow to cure for 30 minutes undisturbed (no weight or handling) Final Cure: Allow 24 hours for load-bearing weight Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly. Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more. FAQ Is Gorilla Epoxy gap filling? Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight. What is the shelf life? Are there storage tips to extend the shelf life? Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix. What is the best application temperature? For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time. Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C Do I need to use clamps with Gorilla Epoxy? How long? Clamps are recommended for use during setup to ensure the bond sets correctly. Set Time: 5 minutes to mix, apply and position Handling Time: Leave 30 minutes undisturbed (clamping is recommended) Full Cure Time: 24 hours for load-bearing weight How much Gorilla Epoxy do I apply? Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond. Average coverage from our 25 mL epoxy syringe will cover 100 square inches. What can I use as a mixing tray or stir stick? A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing. What is Gorilla Epoxy? Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results. How do I remove Gorilla Epoxy? Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding. Uncured Removal: Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps. Hair: Isopropyl alcohol Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric. What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more! What surfaces will Gorilla Epoxy bond? Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®. How do I dispense Gorilla Epoxy? Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
$17.25
You have seen 144 out of 178 products
Clear-drying adhesives, sealants and fillers for invisible bonds and neat edges on glass, plastics and décor. Ideal where appearance matters. Use filters to refine by chemistry, set speed and temperature rating. Always check the product page and TDS/SDS for prep and cure.
