In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Earl’s MulTflex® Exterior Flexible Filler is a unique, single-pack, ready-to-use flexible filler and adhesive formulated for lasting repairs on timber and masonry. It delivers a durable, non-shrinking, non-sinking finish that won’t crack with vibration and won’t fall out, making it ideal for exterior maintenance where movement and weather can defeat ordinary fillers. Paintable when dry and formulated with no volatile organic compounds (No VOCs), it’s a dependable, low-odour solution for professional results at home or on site. Proudly 100% Australian made and owned.
Why you’ll love it
Exterior-grade flexibility: absorbs movement and vibration without cracking.
Non-shrink & non-sink: holds profile and edge detail after cure.
Won’t fall out: engineered adhesion for long-term durability.
Ready to use: straight from the tub — no mixing, no mess, no waste.
Paintable: achieves a seamless, colour-matched finish once dry.
No VOCs: low odour, solvent-free formula.
Interior / Exterior: versatile enough for both.
Proudly Australian: made and owned in Australia.
Where it works
Use Earl’s MulTflex® to repair and rebuild on a wide range of common building substrates:
Timber: decks, window frames, trims, fascia, general carpentry repairs.
Masonry: brick, block, render and patching mortar-like defects.
Plasterboard: exterior-exposed linings under cover and general patching.
Metals & gutters: non-structural filling and profiling (clean, sound, free of rust).
Around pipes & penetrations: neat, gap-free finishing before painting.
Glass & surrounds: edge repairs and feathering prior to topcoating.
Ideal projects
Rebuilding weathered or rotten timber edges before repainting.
Filling cracks and surface imperfections in rendered walls.
Profiling and feathering joints and transitions for a paint-ready finish.
General exterior maintenance where a flexible, paintable filler is essential.
Directions
Surface Preparation
Remove loose or flaking material, dirt, dust, oil, grease and chalky paint. Substrates must be sound.
Ensure surfaces are dry and free from visible moisture. Treat rust and stabilize friable areas as required.
For best mechanical key, lightly abrade glossy surfaces and remove dust.
Application
Open the tub and use directly. If the surface of the product begins to dry, add a few drops of water and re-mix gently. Keep the container tightly sealed when not in use.
Apply with a filling knife or trowel, pressing firmly to ensure full contact with the substrate.
Build up in thin layers for deep repairs, allowing each layer to firm before adding the next.
For a satin-smooth finish, tool the final pass with a wet knife or brush to reduce post-work finishing.
Finishing & Painting
Allow to dry fully. Dry time varies with film thickness, temperature and humidity.
Once dry, apply a suitable primer/undercoat if required by your paint system, then topcoat.
Use quality exterior paints for weather-exposed areas.
Clean-Up & Storage
Clean tools and splashes with water while wet.
Reseal immediately after use to minimise skinning and reduce waste.
Store upright with lid sealed. Do not allow contents to dry out.
Good to know
Formulation is unaffected by normal temperature swings and resists cracking with vibration.
Designed for exterior flexibility yet also suitable for interior touch-ups.
For best results on deep voids, fill in multiple light applications rather than one heavy pass.
Specifications
Brand
Earl’s
Product
MulTflex® Exterior Flexible Filler
Type
Single-pack, ready-to-use flexible filler & adhesive
Use
Interior / Exterior
Paintable
Yes, once fully dry
VOC Content
No VOCs (as supplied)
Shrink / Sink
Non-shrinking, non-sinking
Flexibility
Resists cracking with vibration and movement
Clean-Up
Water (while wet)
Substrates
Timber, masonry, render, plasterboard, metals, gutters, around pipes, glass
Finish
Satin-smooth when tooled with a wet knife or brush
Packaging
Ready-to-use tub
Country of Origin
100% Australian made & owned
Limitations
Do not apply to unsound, dusty or actively corroding surfaces without proper preparation.
Dry and cure times depend on depth and conditions; confirm dryness before painting.
Not intended for structural repairs.
Pro Tips
Feather edges wide for invisible paint blending on weathered timber and render.
Keep a small cup of clean water nearby to maintain a smooth final pass.
Deep cavities: bridge with successive thin layers for the most stable result.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Overview
This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors.
Key Features
Neutral Cure Technology: Low-odor curing system suitable for sensitive applications.
Permanently Flexible: Retains elasticity over time without cracking or shrinking.
Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress.
Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure.
Excellent Adhesion: Bonds strongly to most common building materials without primer.
Easy Application: Smooth flow from the tube, easy to tool and clean before curing.
Applications
This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for:
Sealing around window and door frames.
Lap joints in metal guttering and roofing sheets.
Bonding panels such as wood, plasterboard, insulation board, and drywall.
Fixing masonry joints including sills, brickwork, and decorative trims.
Gap filling around pipes, conduits, and penetration surfaces.
General sealing in kitchens, bathrooms, and living areas where flexibility is required.
Limitations
Not suitable for permanent water immersion (e.g., underwater joints or continuous water load).
Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics.
Not intended for deep cavity filling without adequate moisture for curing.
Surface Preparation
To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant.
Application Instructions
Remove the cap and pierce the nozzle seal.
Apply steadily along the joint or surface, ensuring continuous contact.
Smooth or tool the bead before skin formation occurs.
If masking tape is used, remove immediately after tooling to avoid tearing the cured seal.
Curing
At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint.
Cleaning & Maintenance
Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture.
Health & Safety
Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance.
Why Choose This General Purpose Silicone Sealant?
This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort.
Technical Specifications
Technology
Neutral Cure Silicone
Appearance
Clear Paste
Working Time
Up to 15 minutes
Tack-Free Time
Approximately 15 minutes
Full Cure at 23°C
24 hours
Flexibility
Permanently elastic after curing
Weather Resistance
Unaffected by rain, snow, UV, and temperature variations
Applications
Windows, doors, guttering, masonry, panels, pipes, decorative elements
Storage
Below 25°C, out of direct sunlight
Shelf Life
12 months from manufacturing date
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive
All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation.
Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing.
Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions.
Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including:
Expansion joints in walls and cladding
Sealing around doors and window frames
Sealing penetrations in walls and floors for pipes
Sealing joints in concrete and masonry elements
Sealant for draught-proofing and general sealing and filling applications
Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on:
Aluminium
Steel
Powder-coated metals or glazed tiles
Concrete, aerated concrete, cement-based renders, mortars, and bricks
Application of Sikaflex® Pro+
Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.)
Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face.
Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying.
Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish.
Remove the masking tape and clean up immediately.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Premium Wet Area Sealant
Wet areas
Baths, showers, toilets
Easy to use
Contains strong fungicides to fight mould
Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors.
Built-in fungicides for mould resistance
For both exterior and interior use
Excellent weatherability, resistant to ageing and UV radiation
Resistant to chemicals and temperature
Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood
Very good tooling and smoothing properties
Time-saving with an easy cleanup system
Please note that colour samples are not true to the actual colour. This is a guide only.
Characteristics
1-component acetate-curing silicone sealant
Excellent weathering, ageing, and UV resistance
Enables a great finish, will not string during application
Good tooling and smoothing properties
Contains fungicides
Medium skin formation time for easy handling
Very good adhesion on ceramic substrates
Primerless adhesion to many substrates
Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm²
Meets DIN 18545, part 2D (German industrial standard)
Available in a variety of colours (custom colours available upon request)
Fields of Application
Sealing connection joints between ceramic tiles, showers, baths, and flooring sections
Expansion/movement joints in bathrooms and wet areas
Connection joints on door and window frames
Sealing double-glazing joints
Glass block glazing
Sealing general building substrates
Suitable for interior and exterior use
Important Information
Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates.
While curing, small amounts of acetic acid are released — ensure good ventilation
After curing, the product is odourless and harmless
Thicker silicone layers require longer vulcanisation time
Not for full-surface bonding unless construction prerequisites are met
For layers over 15mm, contact our technical department
Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints)
When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray
Technical Properties
Skin-forming time (23°C / 50% RAH)
~ 15 min
Curing in 24h (23°C / 50% RAH)
~ 2–3 mm
Processing temperature
+5°C to +35°C
Viscosity (23°C)
Pasty, stable
Density (23°C, ISO 1183-1)
~ 1.0 g/cm³
Shore A hardness (ISO 868)
~ 20
Permissible movement capability
—
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
UHU All Purpose Adhesives Super Strong & Safe, the super strong and super fast adhesive, which is adjustable - no instant finger bonding. Suitable for virtually all flexible, solid, porous and non-porous materials. Formula patented. Withstands vibrations and tremors. Moisture and heat resistant from -50°C to +100°C.
Materials
Universal - glues porcelain, ceramic, many plastic materials, metal, wood, glass, leather, rubber, Styrofoam®, paper, cardboard.
Not suitable for leather clothing, textiles, PE and PP.
Use and Handling Instructions
Surfaces to be stuck together must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. Press parts together. Glue joint remains correctable for approx. 20 seconds. The thinner the film of adhesive, the stronger the bond.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tommy Tape® Self-Fusing Silicone Tape
The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road.
Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs.
Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater.
Why you’ll love it
Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C).
Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V).
Leaves no residue: no adhesive means no sticky mess when removed.
Weather- & waterproof: seals within seconds; ideal for outdoor and marine use.
Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends.
Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion.
Popular uses
Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses.
Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first).
Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes.
Marine: mast boot wraps, deck-side waterproofing, salt-spray protection.
Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes.
Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip.
Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances.
Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable.
How to apply (best results)
Prep: Turn power/water off where applicable. Clean and dry the area if possible.
Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor.
Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width.
Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection.
Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets.
Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue.
Specifications
Material
Silicone rubber (self-fusing)
Adhesive
None (bonds to itself on contact)
Dielectric Strength
Up to 8,000 V per layer (build layers for higher insulation)
Temperature Range
−65 °F to +500 °F (approx. −54 °C to +260 °C)
Resistance
UV, oil, salt, weather, and common household/automotive chemicals
Water Performance
Weatherproof & waterproof; can be applied underwater in many scenarios
Elongation
Stretches over 300% for tight, conformal wraps
Removal
Cut off to remove; no sticky residue
Colours / Sizes
Varies by SKU (see options above)
Better than traditional tapes
Feature
Tommy Tape Self-Fusing Silicone
Vinyl / Cloth Electrical Tape
Adhesive
No adhesive (self-fuses)
Pressure-sensitive adhesive (leaves residue)
Waterproof Seal
Yes — seals in seconds; can be used underwater
Limited; adhesive can lift when wet
Dielectric Strength
Up to 8,000 V per layer
Typically ~600 V
Temperature Range
−54 °C to +260 °C
Narrower range; softens or becomes brittle
UV/Chemical Resistance
Excellent (UV, oil, salt, chemicals)
Moderate; can degrade outdoors
Residue on Removal
None — clean cut-off
Commonly leaves sticky residue
FAQs
Can I use it on live electrical circuits?
No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards.
Will it stick to wet or oily surfaces?
Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first.
Is it reusable?
Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed.
What isn’t it for?
Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off.
Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Fix-All Adhesive is a great all-purpose solvent glue and sealer. It seals and repairs almost any surface easily and quickly. A great product for gluing wood, fabric, brick, canvas, and concrete. Also repairs tears and helps fill cracks and holes.
Pacer Technology Super Glue Fix-All Adhesive (T-FA) is a single component adhesive that glues, seals and repairs and is best used for:
• Metal
• Plastics
• Ceramics
• Wood
• Glass
• Rubber
• Fabrics
• Brick
• Leather
• Canvas
• Concrete
• China
• Vinyl
• Porous materials
• Non-Porous
materials
Properties:
Initial colour: Clear
Final colour: Clear to light yellow
Open Time: 10 minutes
Dry Time: 30 minutes
Handling Time: 3 hours
Full Strength: 24 hours
Operating Temperature Range: -200 to 1500F (-290 to 660C)
Instructions:
Use in a well-ventilated area. Protect work surfaces.
As a glue: Apply to both surfaces and let dry 10 minutes. Press parts together. Full cure in 24 hours. For rough, uneven or very porous surfaces, apply a thick layer to both surfaces and wait 30 minutes before joining parts.
As a sealer: Fill crack or hole with extra amounts of Fix-All and allow to dry. Add additional adhesive as needed.
For repair: To repair vinyl, rubber or fabric tears, apply Fix-All with a spatula behind, through and above the tear. Hold sides together using a strong piece of tape across the tear to hold it tightly. Remove tape after 3 hours. Remove excess with a rubber eraser. Note: when thick layers are required it is better to apply a number of thin coats. Allow curing for 3 hours before handling. Full cure in 24 hours.
Notes: Solvents may evaporate from bottle or tube if left open for prolonged periods. Not recommended for Teflon, Polyethylene or Polypropylene bonding. Avoid constant submergence in water and exposure to extremely high temperatures after cure.
Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected.
Safety:
Contains xylene, naphtha and ethylbenzene. DANGER: liquid adhesive is Extremely Flammable. Harmful or fatal if swallowed. Vapour harmful. Avoid breathing vapours. Use and store in a well-ventilated area away from heat, sparks or flame. May cause eye/skin irritation. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more.
Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for:
• Tile
• Rubber
• Wood
• Metal
• Masonite
• Particle Board
• Plywood
• Leather
• Formica
• Plastic
• Laminates
PROPERTIES:
Initial Color: Amber Dry Time: 30 minutes
Final Color: Amber Full Strength: 24 hours
Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C
Instructions:
Use in a well-ventilated area.
1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface.
2. Apply Contact Cement to both surfaces and wait 10 minutes.
3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time.
4. For optimum strength in all applications, wait 24 hours before using the repaired object.
5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources.
Note: Solvents may evaporate from bottle or tube if left open for prolonged periods.
Storage:
Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected.
Safety:
Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates.
Key Features
Bonds well to a wide variety of substrates without surface pre-treatment
Adheres to damp concrete and other porous materials
Compatible with most construction materials, including EPS/XPS and building wraps
Excellent mechanical strength and weathering resistance
Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified
Ideal for bonding and sealing in indoor and outdoor environments
Where to Use
Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing:
Concrete and masonry
Wood and timber components
Ceramic, stone, and tiles
Metal surfaces
Glass and plastic materials such as PVC, PA, PET, and EPS/XPS
Applications
Adhesive for bonding construction components
Sealant for vertical and horizontal joints
Repairs, renovations, and installations in building and civil works
Technical Information
Composition
Silane-terminated polymer
Density
~1.40 kg/L (ISO 1183-1)
Shore A Hardness
~36 (after 28 days)
Tensile Strength
~1.5 N/mm² (ISO 37)
Elastic Recovery
~75 % (ISO 7389)
Service Temperature
−50 °C to +80 °C
Curing Rate
~3 mm per 24 h (at 23 °C / 50 % r.h.)
Skinning Time
~35 minutes (at 23 °C / 50 % r.h.)
Colour Options
Available in White, Concrete Grey, and Black.
Packaging
290 ml cartridge | 12 cartridges per box
Storage & Shelf Life
Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date.
Certifications
CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM)
GEV-EMICODE EC 1PLUS (Very Low Emissions)
LEED v4 EQc 2 Low-Emitting Materials compliant
French VOC Regulation Class A+
Why Choose Sikaflex®-111 Stick & Seal
This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer.
USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction.
Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics.
CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free
Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts
Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic.
Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower
Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only.
Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart.
ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department.
Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility.
RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin!
OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Usage
Sikasil®-670 Fire is designed for fire rated movement and connection joints on porous and non-porous substrates.
Advantages
Up to 4 hours fire resistance according to AS 1530.4
Up to 4 hours fire resistance according to EN 1366-4
Very good resistance to weathering
Movement capability of ± 35% (ASTM C 719)
Easy to smooth and very good workability
Good adhesion to many different substrates
Neutral curing
Colour
Grey
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Packaging 500 ml plastic tube
5 l and 10 l plastic pail
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys White For Life Ready To Use Grout is a water-based easy to use, brilliant white grout, ideal for wall and floor tiles and for joints up to 5mm wide. It resists yellowing, staining or blackening, when used as a part of the Selleys White For Life™ Tiling System and as per pack directions*.
Provides superior water resistance, mould and soap scum resistance
White For Life – Always looks like new*
Resists yellowing, staining and blackening*
Crack resistant
Sand free - resists scratching files
Suitable for indoor wall and floor tiles
Comes in a cartridge for minimum wastage
Where can this product be used?
Bathrooms
Showers (walls only)
Toilets
Laundries
Kitchens
What materials is this product suitable for?
Ceramic tiles
Porcelain tiles
Stone tiles
Most other tiles
Please contact your store to confirm avaliability, as some stores may have a limited range.
How to Use
Preparation
For new tiling jobs, use Selleys White For Life Tiling Adhesives. Ensure that the tile adhesive has set (usually 24-48hrs). Remove spacers, rake out excessive, dust, debris etc from the joints. If re-grouting remove old grout and clean thoroughly with Selleys Rapid Mould Killer and allow to dry. Do not grout at temperatures below 10°C, or in damp conditions. Before grouting, check ease of removal from matt or textured tile surfaces. Seal porous tiles before grouting or removal of grout from tiles will be difficult.
Application
Cut seal, screw on nozzle, cut to size. Apply with a caulking gun, forcing grout into joints (for cartridge only). Grout small areas at a time.
Work the grout into the joints and smooth off using a rubber squeegee or grout float, moving diagonally across the joints with several passes to compact the grout lines and minimise the amount left on the face of the tiles – avoid moving along the joint as this removes grout from the joint.
Tip: hold float/squeegee at 45° angle; clean regularly. Clean up with water, before grout sets.
Allow grout to firm up in joints for approx 20 min (longer in colder conditions).
Using a damp (not wet) sponge, clean tile surfaces, by wiping lightly, in a circular motion. Finish with a single wipe diagonally across the tile with a clean damp ( not wet) sponge. Avoid repeated wiping as this may remove grout which is not yet fully set, from the joints.
Buff and polish the tile surface, after 24hours, with a soft clean cloth. Use Selleys White For Life Grout Cleaner for any stubborn haze marks.
overage
1 cartridge is sufficient for 2sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
1.4kg is sufficient for 6sqm of tiling (300mm x 30mm tiles; joint depth 5mm and width 3mm).
Limitations:
Not for areas frequently immersed in water eg. Shower floors.
Allow to dry for 3 days before exposing grout to water on shower walls.
Handy tips
If the grout is overworked or excessive water is used to smooth off, it may appear to shrink – simply apply a second coat to affected areas.
*To maintain whiteness and long term stain & mould resistance:
Allow grout to set for 3 days before sealing Selleys White For Life Sealer for maximum stain resistance. Reapply sealer annually or whenever grout has been scrubbed hard.
Clean grout and tiles regularly with Selleys White For Life Tile & Grout Cleaner to avoid build up of soil or soap scrum. Do not use harsh acidic cleaners.
Areas subject to high foot traffic will require frequent cleaning.
Clean up spills immediately – grout will resist penetration by common stains for up to 10 minutes.
Coverage guide
1 cartridge is sufficient for 2m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
1.4Kg is sufficient for 6m2 of tiling (300mm x 30mm tiles; joint depth 5mm & width 3mm)
Clean Up
Clean up tools with water before product hardens.
Uncured product may be removed with water.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens.
Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
Mould resistant
Precision application for the best finish
Where can this product be used?
Showers
Baths
Spas
Sinks
Metal, copper and brass plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Powder coated aluminium
Aluminium
Plastic laminates
Rubber
Glass
Stainless steel
Concrete
Size
100g Aerosol can
Technology
Neutral Cure Silicone
Use
Interior
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
1. Throughly clean and dry surface from oil, dirt and grease with mineral turps.
2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
4. Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Sealant is not paintable.Complete painting 7days prior to applying sealant.
• Not for aquariums or contact with food, eating utensils or drinking water.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Wet Area Ezi Press is ready to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and resistance to unsightly mould. Ideal for wet areas like bathrooms and kitchens.
Best for : Ceramic, glazed and porcelain fixtures, Metal, copper and brass fittings, Powder coated aluminium, Aluminium, Plastic laminates, Rubber, Glass, Stainless steel, Concrete
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
Mould resistant
Precision application for the best finish
Where can this product be used?
Showers
Baths
Spas
Sinks
Metal, copper and brass plumbing Fixtures
What materials is this product suitable for?
Ceramic, glazed and porcelain fixtures
Metal, copper and brass fittings
Powder coated aluminium
Aluminium
Plastic laminates
Rubber
Glass
Stainless steel
Concrete
Size
100g Aerosol can
Technology
Neutral Cure Silicone
Use
Interior
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
1. Throughly clean and dry surface from oil, dirt and grease with mineral turps.
2. Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
3. Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
4. Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Sealant is not paintable.Complete painting 7days prior to applying sealant.
• Not for aquariums or contact with food, eating utensils or drinking water.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Urethane Bond Is a high strength shock proof, water and chemical resistant polyurethane adhesive.
Features
High strength
Achieves maximum bond in 48 hours Shockproof
Flexible, shatterproof and impact resistant so it can take knocks Durable
Lasts a long time Chemical resistant
Wont break down by temporary exposure to most chemicals i.e. solvents Waterproof and weatherproof
Good for bonds exposed to the elements When curing, Urethane Bond expands, filling voids and strengthening the bond Easy to use
Requires no mixing, ready to use straight from the pack Only need to apply adhesive to one surface Versatile
Can be used inside or outside Sandable and paintable after dries
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sil-X advanced polymer technology is formulated to deliver superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Sil-X has been specially developed to withstand the tough Australian and New Zealand conditions. Selleys THE ONE Adhesive delivers superior bond strength on any building surface. Can be applied to wet or dry, interior or exterior, porous or non porous surfaces*. Extreme versatility that takes the guess work out of DIY.
Features
Strong bond on any building material
Can be applied to wet or dry surfaces
Suitable for interior and exterior applications
Can be used on porous and non-porous materials
Will adhere to oily surfaces
Low VOC
Excellent weather resistance
Flexible and long lasting
Paintable with water-based paints
What materials is this product suitable for?
Suitable for all building materials*
How to use this product
Ensure surfaces are clean and free from grease or loose particles.
Cut tip of cartridge, fit nozzle and cut at 45ºangle to desired size before placing in a cartridge gun such as Selleys Light Speed Caulking Gun.
Apply with a caulking gun, pushing adhesive onto the surface.
Position pieces and press firmly together. Larger, heavier materials may need to be supported until the adhesive cures.
If painting, paint with water-based paint.
Handy tips
Keep a pack of SELLEYS Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
Limitations
*Not for PE, PP, PTFE, or permanent water immersion
Clean up
Clean up with turps before the adhesive cures.
Safety tips
Keep out of reach of children.
Avoid skin and eye contact and breathing vapours.
Use in a well ventilated area.
Wear protective clothing, gloves and eye protection.
If on skin, wash with soap and water.
Cure product before disposal.
Product releases methanol during cure.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant.
Features
Can be applied to wet or dry surfaces*
Good adhesion on any surface* even when applied in the rain
Excellent UV and weather resistance
Suitable for interior and exterior use
Long lasting flexibility
Easily paintable with water-based paints
Low VOC – so can be used in any environment without discomfort
Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry.
Where can this product be used?
Perfect for use on and around:
Skylights
Gutters
Downpipes
Windows
What materials is this product suitable for?
Concrete
Timber
Metals
Cement sheeting
Brick
Plasterboard
Ceramic Tiles
Fibreglass
All construction substrates
Most plastics*
How to use this product
Ensure substrates are clean and free of oil, grease or loose particles.
Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun.
Apply with the caulking gun, pushing sealant into joint or gaps.
Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint.
Storage and re-use
Store in cool, dry conditions below 30°C.
Use within 6 months of opening.
Clean up
Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
Handy Hints
For neater joints, mask sides before applying sealant and remove the tape before sealant skins.
Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting.
Limitations
Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure.
Safety tips
Cure excess product before disposal.
Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water.
Ensure use in a well-ventilated area.
Additional information is provided in the Safety Data Sheet.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Roof & Gutter Ezi Press is easy to use – simply press the lever to apply – no caulking gun required. It provides a superior waterproof seal and excellent UV and weather resistance. Ideal for roofing, guttering and flashing outside the home.
Best for: Aluminium, Sheet Metal, Copper, Brass, Galvanised Metals, Rigid PVC and most plastics including polystyrene, Terracotta, Concrete, Glazed tiles, BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Features
No caulking gun required
Easy to hold and use
Superior waterproof seal
100% silicone - resists cracking, crumbling or peeling away
UV and weather resistant
Precision application for the best finish
Where can this product be used?
Metal and tile roofing
Colorbond roofs and fences
Guttering and flashings
Skylights
Around air conditioning units
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
Use in a well ventilated are. Avoid contact with skin and eyes.
Throughly clean and dry surface from oil, dirt and grease with mineral turps.
Remove tab lock, twist collar clockwise to MAX, remove nozzle cap, press lever to dispense.
Smooth with a spatula dipped in soapy water. Clean up before sealant skins (5-10 minutes) with a cloth dampened in mineral turps. Twist collar back to MIN and replace nozzle cap
Sealant will fully cure in 72 hours
Limitations:
• Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
• Do not use in below ground applications.
• Sealant is not paintable. Complete painting 7d prior to applying sealant.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
UV and weather resistant
Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal
Non corrosive neutral cure formula
Has superior flexibility +/- 25% movement capability
Temperature resistance - approximately -60°C +150°C
Suitable for contact with drinking water - complies with AS/NZS 4020#
25 year guarantee* against crumbling, cracking and peeling away
Selleys Roof and Gutter Silicone is a neutral cure (non-corrosive) 100% silicone sealant suitable for most building surfaces including metals, tile, cement sheeting, PVC and Colorbond® roofing. It is available in a variety of colours, including a range of Colorbond(R) matches, to suit your roof and gutters.
Where can this product be used?
Metal and tile roofing
All metal lap-joint waterproofing
Colorbond roofs and fences
Guttering and flashings
Vents and downpipes
Weatherproofing caravans and trucks
Copper, brass and zinc
Skylights
What materials is this product suitable for?
Aluminium
Sheet Metal
Copper
Brass
Zinc
Galvanised Metals
Rigid PVC and most plastics including polystyrene
Rubber
Glass
Terracotta
Concrete
Glazed tiles
BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND
How to Use
Use in a well ventilated area. Avoid contact with skin and eyes.
Thoroughly clean and dry surface from oil, dirt and grease with mineral turps.
Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge and insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint.
For a smooth finish, tool with a spatula dipped in soapy water. Clean up before sealant skins in 5-10 minutes, with a cloth dampened in mineral turps.
Sealant will cure in 72 hours. At this point any unneeded sealant can be removed by trimming with a sharp blade, but avoid under-cutting the seal.
Limitation:
• Not paintable. Complete painting 7 days prior to applying sealant.
• Not recommended for use as a plug for burst pipes.
• Do not use in below waterline applications.
^Not for use on polyethylene, polypropylene or Teflon - pre-test plastics before use
Handy tips
For neater joints, mask sides before applying sealant and remove tape before sealant skins.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant.
For a better finish use a spatula dipped in mineral turps or soapy water to tool off the sealant.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish.
If there is old silicone which needs to be removed, we recommend using Selleys Silicone Remover, this ingenious product makes removing old silicone easy.
*Warranty Information
* Refer to product label for full conditions. This guarantee does not limit and may not necessarily exceed your rights under the Competition and Consumer Act 2010.
Clean up
Uncured product may be removed with mineral turps.
Cured product can be removed with Selleys Silicone Remover or by cutting and scraping.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Paint Over Sealant is a permanently paintable sealant.
Features
Paintable
Smooth flawless finish.
Easy to use and can be used on damp surfaces.
Superior adhesion to most building materials.
Low odour so can be used in any environment without discomfort.
Weather resistant by forming a durable seal which remains flexible, not drying or cracking
Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch.
Temperature resistance – approximately -40°C +93°C
Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying.
May be discoloured by contact with alloys containing brass, copper or zinc.
Do not allow unused product to freeze.
Where can this product be used?
10879.Window frames that need painting
102879.Capstones Masonry walls that need painting
Perfect for use on or around:
Bricks and concrete
Windows frames
Tiled and wooden fixtures
Areas where a sealant is needed and where you want to paint it
Not suitable for use in below waterline applications.
Not suitable for use on oily woods such as cypress, teak or cedar.
Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use.
What materials is this product suitable for?
Glass
Aluminium
Fibre Cement
Painted Surfaces
Ceramics
Masonry
Most metals
Most plastics
Wood
How to use this product
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant.
Remove the tape before the sealant skins.
For a better finish use a spatula dipped in detergent and water to tool off the sealant.
Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
To improve the paint finish, wipe the sealant with detergent solution immediately before painting.
Avoid smearing sealant on the surrounding surfaces as this may effects its paintability.
Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish.
Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
Safety tips
Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice.
Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin.
Avoid breathing in vapours.
Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing.
For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor.
For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
Keep away from children.
Storage and re-use
Store in cool dry conditions, below 30°C
The sealant should be used within 6 months after opening.
After use keep the nozzle on the cartridge
Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life.
If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required.
For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air.
When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use.
If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary
FeaturesSuperior formulation+ that stops mould growth*Fast skinning formulation which means you can use your shower in 1 hourProvides a durable waterproof sealResists lifting
Where can this product be used?Suitable for use in humid and damp environments such asKitchensBathroomsLaundriesShowersBasinstilesWorktopsBaths & spasPlumbing fixtures
What materials is this product suitable for?CeramicGlazed & porcelain fixturesAluminiumPlastic laminatesSome rubbersGlassStainless Steel
How to UseBefore applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mouldThoroughly clean surface where sealant will be applied with turps and dry completelyCut nozzle at 45°angle, cut cartridge tip and fit nozzlePlace in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the jointTool with a spatula dipped in detergent water within 5-10 minutes of applicationClean up with turps before product skins
Limitations:
+Compared to Selleys Wet Area#Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours)*To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growthNot suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility
TipsFor neater joints, mask sides before applying the sealant and remove the tape before sealant skinsNot paintable. Complete painting 7 days before applying the sealant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear.
Features
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer.
Has greater than 300% elongation/stretch and up to +/- 15% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage.
Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application).
Is formulated for long term resistance to cracking and crumbling.
Easy water clean-up
Will not stain building materials.
Has good resistance to weathering.
Low toxic, low odour, low VOC, less harmful to the environment
Where can this product be used?
Between window and door frames and the wall
Along skirting boards
Around cornices
Between benchtops and tiles which are not exposed to water
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Paint
Many other building materials
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Interior Colours is a flexible gap filler available in a range of modern colours, to fill those unsightly gaps and cracks around the home and take away the need to paint.
Features
Available in a great colour range, so no need to paint.
Paintable if required.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for long. Has greater than 350% elongation/stretch and up to +/- 20% movement capability.
Superior adhesion to a broad range of surfaces, resulting in a lasting finish.
A smooth flawless finish and minimal shrinkage
Can be painted over with both water and oil-based paints, after the surface has skinned. (Approximately 30 minutes after application).
Wide joints are best left for 48 hours before painting as some paints shrink during drying that can cause the paint to crack
Is formulated for long term resistance to cracking and crumbling.
Is water-based, so can be cleaned up with water.
Will not stain building materials.
Has good resistance to weathering.
Mould and mildew resistance.
Where can this product be used?
Between window and door frames and the wall.
Along skirting boards.
Around cornices.
Between benchtops and tiles which are not exposed to water.
In corners or between walls and ceilings
Between cabinets and cupboards
Around air conditioning vents and the ceiling
Where shrinkage or movement has caused rigid fillers to crack
Gaps with the maximum width of 25mm and depth of 12mm.
What materials is this product suitable for?
Timber
Brick & Concrete
Plasterboard, particleboard & fibre cement sheeting
Masonry
Ceramic Tiles
Glass
Aluminium
Bare or painted surfaces
Colorbond
Many other building materials
How To Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut the seal and nozzle and fit to the top of the cartridge. Insert the cartridge into a caulking gun such as Selleys Light Speed Caulking gun.
Hold the caulking gun at a 45° angle and apply, forcing product into gap
Smooth with a wet finger or spatula
Clean up excess with a damp cloth immediately and clean hands and tools with water.
Allow surface to skin thoroughly prior to painting with water-based paints. If oil-based paints are to be used, or if gaps are large, allow sealant to set for about 24 hours and ensure the product is completely cured.
Avoid water contact until fully cured- 72 hours or longer in cold weather.
Limitations:
Not recommended for foot traffic areas, gaps between tongue and groove boards or weatherboard overlaps. Use Selleys(R) No More Gaps(R) Timber Flooring Flexible Gap Filler for gaps between tongue and groove boards. Use Selleys(R) No More Gaps(R) Exterior & Weatherboard Gap Filler for weatherboard overlaps.
Not suitable for areas in prolonged contact with water eg. showers, pools & spas. Where significant joint movement occurs, or for areas of frequent water immersion, use the appropriate Selleys(R) Silicone Sealant.
Do not apply or store below 5°C.
Handy Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying the product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler.
Allow the surfaces to the skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions.
Some water-based undercoats and flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints.
Keep a pack of Selleys Sugar Soap Wipe handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bathroom & Kitchen is a flexible gap filler with superior water and mould resistance for bathroom and kitchen surfaces.
Features
Superior water resistance.
Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Up to +/- 25% movement capability.
Optimum adhesion is achieved on ceramics, glass, aluminium, most plastic and cement.
Mould resistant-contains a fungicide to help protect against unsightly mould growth.
Can be painted over with both water and oil based paints
Easy water clean-up
Low odour
Where can this product be used?
Bathroom vanities
Bathroom cabinets
In and around glass and tiles
Cabinets
Architraves
Skirting boards
Bench tops
Windows
Door frames
What materials is this product suitable for?
Ceramics
Glass
Aluminium
Most Plastics
Cement Sheeting
Wood
Plasterboard
Many other building surfaces
Ensure the surface is clean and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut seal and nozzle and fit to cartridge. Insert into a quality caulking gun, such as Selleys Light Speed caulking gun.
Apply with caulking gun, forcing product into gap
Smooth with a wet spatula.
Clean up with a damp cloth immediately, before filler skins in approx. 10-15 minutes.
Allow surfaces to skin prior to painting (approximately 1 hour). Skin time will be extended in cold or humid conditions, or if painting with flat or ceiling paints (approximately 3 hours)
To allow product to strengthen, protect from water for 24 hours.
Limitations:
Should not be used in permanently damp locations. Use Selleys® Wet Area Silicone Sealant around sinks, baths and shower recesses.
Not recommended for prolonged contact with water.
Tips
Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up.
When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of gap filler.
Remove the tape before the gap filler skins.
If you are going to wipe off the excess gap filler with a wet finger, ensure you wet your finger with water and not saliva, as saliva contains bacteria and this will increase the chances of mould growing in your gap filler. It is best to use a spatula dipped in soapy water.
Clean off all excess No More Gaps Bathroom & Kitchen from equipment immediately before it cures with a damp cloth. Once cured, No More Gaps Bathroom & Kitchen is extremely difficult to remove and must be trimmed with a knife.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
To avoid paint cracking, apply at temperatures above 5°C and do not apply paint too thick.
Allow longer drying times before painting with flat or ceiling paints and in cooler weather.
Can be applied to damp surfaces however product must be allowed to dry following application.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home.
Features
Ready mixed mortar filler, so is quick and easy to apply with a caulking gun.
Has a mortar like texture for a textured finish and match to cement mortar and render.
Is more flexible than mortar which will help prevent more damage to the mortar
Is weather and UV resistant with a UV stable formula to prevent colour deterioration.
Provides a more suitable finish on rendered walls than smooth fillers.
Contains a fungicide and algaecide to protect against unsightly mould and algae growth.
Has superior adhesion to a broad range of surfaces, making it easy to use.
Will not stain building materials
Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application).
Is water based, so can be cleaned up with water easily.
Is sandable when dry for a rough or smooth finish.
Where can this product be used?
Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded.
Stationary cracks in pathways.
Sealing gaps around windows or between brick wall and roof eaves.
Repairing stationary cracks in cement render.
Repairing penetration holes around pipe work, ducting, etc.
Sealing gaps where mortar has fallen out in ridge capping on tile roofs.
What materials is this product suitable for?
Brick
Concrete
Render
Fibre cement sheeting
Laminated plastics
Hardboards
Aluminium
Ceramics
Timber
How to Use
Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk.
Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun.
Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger.
Clean away excess from surfaces immediately using a damp cloth.
For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather.
Protect from rain until firmly skinned.
Limitations:
Not suitable for areas of continuous water immersion.
Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar.
Not suitable for moving cracks.
Do not use or store below 5°C.
Handy Tips
For the best results slightly dampen the surface prior to application.
For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render.
If painting over the product, apply undercoat before applying a top coat for the best results.
Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
This multipurpose silicone is a neutral (non-acid) curing, one part sealant for interior and exterior use. It is specially formulated to seal out water in a wide variety of situations, where an excellent quality flexible seal with outstanding adhesion is required.
Superior adhesion.
Non shrinking.
Mould resistant.
Low odour.
Non corrosive.
Sealants/adhesives engineered to accommodate movement without cracking. Check stated movement capability for your joint design. Use filters to refine by chemistry and cure speed. Always review the product page and TDS/SDS.
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
![Selleys Wet Area Sealant EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys Wet Area Sealant EZI Press [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](http://gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](http://gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](http://gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](http://gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](http://gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys Mortar Works Mortar Filler [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/9300697115331_e7d5a048-59cc-4fa4-b476-9627eaad83a2.jpg?v=1754711856&width=645)
![Selleys Mortar Works Mortar Filler [Sandstone]](http://gluesaustralia.com.au/cdn/shop/files/1097_1101_d8d532a7-4e5b-44a3-b89a-52d72182b07b.jpg?v=1754711858&width=645)
![Sika Sikaflex Pro+ Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](//gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](//gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](//gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](//gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](//gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](//gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](//gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](//gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](//gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](//gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](//gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](//gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
![Sika SikaSil 670 Fire Rated Silicone Sealant [Grey]](//gluesaustralia.com.au/cdn/shop/files/9318324012236_d7a5d83c-0ea4-4a46-88bb-55e873bf5a05.jpg?v=1754711696&width=645)
![Sika SikaSeal 300 Glass & Weather Seal [Transparent]](//gluesaustralia.com.au/cdn/shop/files/9318324011314_17b1b8c7-fa52-428b-bf6f-872b3b964d3b.png?v=1754711699&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys Wet Area Silicone Sealant Speed Seal 1 Hour [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697122629_597e18e6-75e4-42a2-a468-6311b7fae1b1.jpg?v=1754711756&width=645)
![Selleys Wet Area Sealant EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125415_d295dbcb-92c9-46a5-87c2-399a71ec73f3.png?v=1754711757&width=645)
![Selleys Wet Area Sealant EZI Press [Clear]](//gluesaustralia.com.au/cdn/shop/files/9300697125750_81b22ff4-49f4-4011-b6d5-6ee33f923b0f.jpg?v=1754711759&width=645)
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](//gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
![Selleys Roof and Gutter EZI Press [Translucent]](//gluesaustralia.com.au/cdn/shop/files/9300697125859_12479a9f-d839-46ee-b806-5616cb151762.jpg?v=1754711801&width=645)
![Selleys No Mould Silicone Sealant Waterproof [Translucent]](//gluesaustralia.com.au/cdn/shop/files/b491df0a1d2e4750abba298eed7eeb4d.jpg?v=1757753045&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](//gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Selleys No More Gaps Timber Floors x 380g [Jarrah]](//gluesaustralia.com.au/cdn/shop/files/42b566f39b234ffeab320faed408b86e.jpg?v=1757753057&width=645)
![Selleys No More Gaps Timber Floors x 380g [Hardwood]](//gluesaustralia.com.au/cdn/shop/files/5160e944b5d3493cbac2a999232381fa.jpg?v=1757753063&width=645)
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](//gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
![Selleys No More Gaps Filler Bathroom and Kitchen [White]](//gluesaustralia.com.au/cdn/shop/files/c1273312b7d1426c8ba82245f6c8d0de.jpg?v=1757753091&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Tranquil Retreat]](//gluesaustralia.com.au/cdn/shop/files/18cfd18e466f43bab8a6fd2d1eaf4bfd.jpg?v=1757753110&width=645)
![Selleys No More Gaps Coloured Caulk Sealant 450g [Timeless Grey]](//gluesaustralia.com.au/cdn/shop/files/047808da6e434754b1b4b492e02434e9.jpg?v=1757753116&width=645)
![Selleys No More Gaps Bricks Mortar [Medium Grey]](//gluesaustralia.com.au/cdn/shop/files/9300697130327_41339ef1-92ff-417a-bab1-8529f0ee07f6.png?v=1754711845&width=645)
![Selleys Mortar Works Mortar Filler [Terracota]](//gluesaustralia.com.au/cdn/shop/files/9300697115331_e7d5a048-59cc-4fa4-b476-9627eaad83a2.jpg?v=1754711856&width=645)
![Selleys Mortar Works Mortar Filler [Sandstone]](//gluesaustralia.com.au/cdn/shop/files/1097_1101_d8d532a7-4e5b-44a3-b89a-52d72182b07b.jpg?v=1754711858&width=645)