Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$15.92
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$16.52
Selleys Seal Fix forms gaskets/seals directly from the tube; any size, any shape. Selleys Seal Fix cures to a tough durable silicone rubber, and is ideal for repairing or replacing worn our seals in domestic ovens, fridges and freezer doors, as well as automotive and appliance gaskets. Seal fix is resistant to chemicals, oil, water, detergent etc. It is safe for incidental contact with food. Features: -High-Temperature resistance up to 260°C** -Durable clear rubber seal -Ideal for vertical applications -Impact resistant -Safe for incidental food contact. Where can this product be used? -Replacing oven door seals -Replacing refrigerator door seals -Dishwasher door seals -Washing machines -Automotive gaskets and seals -Heating and air conditioners -Flanges of all kinds What materials is this product suitable for? -Metal* -Paint/coated surfaces -Glass -Fibreglass How to use this product -Clear surfaces with Selleys BBQ Tough Wipes or Oven Wipes and allow to dry. -Pierce tube seal, fit nozzle and cut to size. -For repair or replacement of oven door seal or oven door glass: Apply Seal Fix to repair or replace seal or glass. -Once the seal or oven glass is fixed in place the repair should be allowed to cure for 7 days before using the oven. -For repair or replacement of refrigerator door seal: Apply Seal Fix to door, bring surfaces together and close door. -Once the seal is glued in place the door needs to be held firmly closed with tape. -Due to the strong magnetic hold of the door seal to the refrigerator body, the repair must be allowed 24 hours to cure before opening the door or subjecting to any stress For repair or replacement of gaskets: -Remove old gasket/seal material and thoroughly clean surfaces with mineral turpentine and dry. If adhesion of gasket is not required wipe mating surfaces with an oily cloth. -Pierce seal in the tube, fit nozzle and cut to size. Squeeze the bead of sealant onto one of the surfaces to be joined, around the perimeter of the part and around bolt holes. -Join parts together within 10 minutes and bolt down to the desired torque. If a thicker gasket is required assemble but do not tighten bolts for 24 hours. Material cures in 24 hours. (When disassembly is required, pry two flanges apart and remove old sealant before reassembly.) Clean Up -Uncured product may be removed with mineral turpentine. Cured product can be removed with Selleys Silicone Remover or by mechanical action. Handy tips -When eliminating cork gaskets, ensure that adequate clearance remains for mechanical parts e.g. valve rocker covers (do not fully tighten until sealant has cured) Limitations *Not for copper brass or galvanised metal surfaces **Not suitable for continuous exposure to temperatures above 205°C or intermittent (more than 2 hours) expose to temperatures above 260°C Not for exhaust manifold or for contact with gasoline or distillate Safety tips -Avoid contact with skin and eyes and breathing vapour -On contact, the uncured sealant can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice -May irritate sensitive skin. If skin contact occurs, wipe off immediately and wash with plenty of soap and water -Ensure use in a well-ventilated area -Product releases acetic acid while curing -For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764 766) or a doctor -For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site Storage and re-use -Store in a cool, dry, well-ventilated place and out of direct sunlight -Keep containers closed when not in use – check regularly for leaks
$13.00
Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Specifications Brand Scotch-Mount™ Overall Width (Metric) 2.54 cm Product Colour White Details Scotch™ Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organise your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Great for do-it-yourself projects
$15.99
Holds up to 4.5kg, 22cm holds 1kg Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Indoor/Outdoor Indoor Overall Length (Metric) 1.3 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Rolls Size 2.5cm x 1.3m Details Scotch™ Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Mounting Tape.
$9.50
Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Good For Outdoors No Indoor/Outdoor Indoor Overall Length (Metric) 2.5 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Squares Size 2.5cm x 2.5cm Details Scotch® Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch® Indoor Mounting Tape. Scotch® is the permanent mounting solution that is fast, easy and does not require the need for any tools. Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Bonds to any smooth, indoor surface Faster, safer, and more versatile than screws and nails Ideal for Indoor use on any smooth surface No need for any tools, nails or screws
$9.96
Scotch Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape holds up to 15 pounds and delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3" To hold 15 lb use 45" Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White
$9.27
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$15.16
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$13.35
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$22.18
Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!
$4.00
There's a lot of grime to be wary of in this world, and there's no reason you should have to put up with it. Prep marathon gets your day off on the right foot by getting your house clean as a whistle again. Reach out today for this hardworking citrus-based cleaner that intensively degreases stubborn messes and is tough enough to tackle kitchen grease spills with ease. And because we use non-petroleum solvers, our lotions are less drying than most brands while still being gentle on hands. Get Prep Marathon Re-Moove-It Cleaner now!
$6.00
Clean the glass and brighten your shower in one go. Prep Marathon Glass Cleaner is a tough enough cleaner to remove streaks from surfaces, but gentle enough for laminates, chrome or any other delicate surface. If you're looking for an easy way to start off every home clean on the right track, order Prep Marathon Glass Cleaner now!
$16.15
No one likes those big, ugly streaks on their favorite mirror--trust us. Make sure your streak-free shine is up to snuff with a bottle of Prep Marathon Glass Cleaner before you start sweating for that marathon! The product is PH balanced and has been laboratory tested. You deserve an honest cleaning every time you use it, which can be easily achieved with this top selling solution!
$4.78
Clean the glass and brighten your shower in one go. Prep Marathon Glass Cleaner is a tough enough cleaner to remove streaks from surfaces, but gentle enough for laminates, chrome or any other delicate surface. If you're looking for an easy way to start off every home clean on the right track, order Prep Marathon Glass Cleaner now!
$6.00
Directions: Well recognised as a cleaning agent, can be used undiluted but traditionally in a diluted form 50/50 with water Uses: General cleaning, glass services & safe on stainless steel. Also safe to use in food preparation areas
$9.47
Prep Marathon is the perfect product for anyone who hates dirtying their hands when cleaning. Our BBQ cleaner combines hunger and cleanliness with a fresh scent to leave your dishes shining like new. When it comes to cooking, this easy prep option is ideal for making sure all of popsicles have made it into mouths safely- but also neat enough to make your house feel like royalty after you're finished!
$4.00
Multi-Purpose Cleaner and Deodorizer Natural Minerals easily dissolve in water Directions: Test on an inconspicuous area first Borax can be used in powder form for tea and coffee cup stains General cleaning 1-table spoon to 4.5 Litres of warm water (also woollens and blankets) Enamel surfaces 4 tablespoons to 4.5 Litres of warm water (refrigerators, stoves, sinks, baths & tiles Uses: General cleaning, stain remover, deodorizer
$9.47
Prep Bi-Carb Cleaner makes stainless sinks shine, tiles sparkle and removes soap scum in showers. Use in the kitchen on benches, cook tops, laminate cupboard doors Deodorise upholstery and carpet by sprinkling with Bi-Carb, letting it sit for 15 minutes, then vacuum it up
$7.22
Directions: - Use gloves before dispensing - Washing Machines: empty machine, add 1 tablespoon of Descaling powder directly into the machine, not detergent dispenser. Run full cycle - Dishwashers: remove all items from the machine, including all dishwashing detergents. Fill detergent dispenser with up to 2 tablespoons of Descaling powder and run for a full cycle. - All-purpose cleaner: 1 tablespoon mix to 1 Litre hot water and soak items for up to 3 - 5 minutes, rinse the solution off in cold water Uses: Can be used undiluted for heavy stains by simply adding power and rob directly onto affected area e.g. bathtubs, sinks and toilet bowls
$11.48
Moisture and mould resistant, this product has been specially formulated for filling cracks, holes and chips in wet areas of the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on Plasterboard, masonry, wood, concrete, mortar & cement board (INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 330mL & 770mL Colour: White Application Tips • Surface to be filled should be clean and dry with no loose or powdery material. Mould affected areas should be thoroughly cleaned with a suitable mould remover, rinsed and allowed to dry. • Using the attached filling blade press filler in firmly and remove excess. • Allow drying (2-3 hours in thin 2-3mm applications depending on humidity), before sanding. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. Allow longer drying times (24 hours minimum) if painting with oil-based paints or for deeper applications. • Finish off sanding with a fine sandpaper (>300 grit) for a smoother finish. • For best results, apply paint undercoat before applying paint topcoat suitable for bathrooms and kitchens, to maximise water, moisture and mould resistance. • Not for areas that will be immersed in water. • Use a flexible Poly sealant where joint movement occurs. • Clean up with water before filler dries. FAQ's Q. Should I use a different filler in damp areas? A. Yes. Polyfilla Bathroom & Kitchen has been specially formulated to resist water, moisture and mould growth making it perfect for use in damp areas of the home. HOW TO PREPARE A BATHROOM OR KITCHEN FOR PAINTING The key to achieving a flawless paint finish is preparation. A fresh coat of paint can often accentuate imperfections on plaster walls so it's important that small cracks, dents and chips are properly filled and sanded to create a smooth, even surface for a picture-perfect finish. In areas affected by moisture such as bathrooms, kitchens and laundries we recommend using products specially designed to resist mould growth. Before starting on your walls, it's a good idea to clear your bathroom or kitchen of accessories and appliances. Use good quality drop sheets to avoid getting paint and dust on benchtops, sinks and floor surfaces. You'll need: Poly Sugar Soap Polyfilla Bathroom & Kitchen A flexible filling blade Fine sandpaper A soft brush Painters tape Ensure your walls have no remaining nails, pins, etc. With fine sandpaper, remove lumps, bumps and any paint flakes. Brush off excess dust and then wash down the walls thoroughly with Poly Sugar Soap to remove mould, grease and grime. Let the sugar soap dry completely before filling. Apply a small amount of Polyfilla Bathroom & Kitchen to your filling blade and draw it across each imperfection on the wall. For larger areas, a trowel should be used. Using the filling blade, remove excess and skim the filled areas lightly in both directions a few times to ensure a no air bubbles are present in the filled space. Feathering the edges will also minimise sanding. Finish by drawing down with firm pressure. Wait until the application has dried (2-3 hours for thin 2-3mm applications depending on humidity), then lightly sand the filled areas to an even finish. Remove dust with a soft brush. Allow longer drying times for deeper applications or if painting with oil-based paints (24 hours minimum). There is no need to use water or sugar soap to clean dry filled surfaces prior to painting. For deeper jobs, apply in 10mm layers allowing each layer to set before applying the next layer. Taping Invest in a good painterís tape and carefully tape off any skirting, architraves, woodwork, etc. As you apply it, gently rub across the edge of the tape that will be painted to help prevent any paint from seeping underneath Now you've created a smooth, blemish-free surface, youíre ready to paint and achieve a perfect finish! For best results, apply paint undercoat before applying your top coat.
$18.00
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.03
![Parfix Kitchen & Bathroom Silicone Sealant 300g [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697115928_85e9adb4-ec92-46ea-8eda-b6ab353e59f8.jpg?v=1754712261&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.14
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
Parfix Fast Grip is a solvent-based contact adhesive that is heat and water-resistant, making it suitable for use in kitchens and bathrooms. Immediate strong bond Heat and water resistant Brush application
$18.00
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive
$11.39
![Monarch Mini Silicone Mould Resistant [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029066_2af7d350-636b-476c-9c8a-71b4ddb4f0e5.png?v=1754712301&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.30
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$7.22
Multi-Purpose Cleaner and Deodorizer Natural Minerals easily dissolve in water Directions: Test on an inconspicuous area first Borax can be used in powder form for tea and coffee cup stains General cleaning 1-table spoon to 4.5 Litres of warm water (also woollens and blankets) Enamel surfaces 4 tablespoons to 4.5 Litres of warm water (refrigerators, stoves, sinks, baths & tiles Uses: General cleaning, stain remover, deodorizer
$10.29
Sealants as good as new in just one step, easy to apply in 5 minutes. Is the sealant in your bathroom mouldy, yellowish, cracked...? Damaged bathroom sealants can ruin the look of your bathroom. Today you can easily re-new with Loctite RE-NEW. There's no need to be an expert DIYer. You can get a great result thanks to its integrated smoothing tool and innovative silicone formula with anti-mould properties. Recomended on:Bathroom, shower and kitchen seals Easily applied over existing joins Covers discolourations and cracks Wipes off easily if mistakes are made Mould resistant Ready to use in just 6 hour HOW TO USE: STEP 1: CLEAN THE DAMAGED SEALANT No need to remove the existing sealant. Clean the existing sealant with a damp cloth. Ensure sealant is dry before applying RE-NEW. If the sealant is too mouldy, use a mould remover first. STEP 2: APPLY RE-NEW Apply RE-NEW on top of the existing sealant, holding the tube with the Loctite logo facing towards you. Shake the tube to bring the RE-NEW content to the bottom. Gently squeeze to apply RE-NEW. Squezeed too hard? Go over the sealant again without squeezing the tube. STEP 3: RELAX: YOU CAN REPEAT Want to try again? Go over the sealant again without squeezing the tube or remove immediately using a damp cloth and start over. Remove excess sealant from surface or hands with a damp cloth. STEP 4: THE PERFECTIONIST'S TOUCH Go over your RE-NEW without squeezing the tube. Thanks to the integrated smoothing tool, the sealant will be smoothed. Good adhesion to existing sealant including siliconeIce white in colour to cover every damaged sealant STEP 5: TA-DA! Clean the smoothing tool with water and a damp cloth. Let it dry for 6 hours before showering!
$16.24
White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004. Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004 LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C. PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.
$44.40
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$13.11
Kwik Grip Waterbased is a contact adhesive that is ideal for bonding flat, close fitting surfaces. Forms a durable, heat and water resistant bond for long lasting results. Features High Strength (Stronger than Kwik Grip or Kwik Grip Gel) Easy to use – Applies white, and turns clear when ready to join surfaces Easy to clean up – Cleans up with water Low odour/Low VOC /Non-toxic – No harmful solvent fumes (Safer than solvent based adhesives). Especially useful if repairing inside your home or in a confined space. E.g. Car. Dries clear – For seamless repairs Instant bond – No clamping required* and in most cases repaired item can be used immediately. (*Clamping of warped or curled surfaces may be required) Suitable for use on horizontal or vertical surfaces Can be used in same method as other adhesives (wet bond) for small repairs. Heat resistant to 130oC Non-flammable Coverage: 500mL tub covers 1 surface up to 2.5m2 depending on porosity Where can this product be used? Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench tops, table tops or other furniture. Areas where clamping or pressing facilities are either not available or difficult to use. Patching vinyl flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Leather work eg handbags Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers and other outdoor equipment Replacing lifting edges or laying lino Attaching rubbers to your fridge door Bonding labels to tins Repairing your wetsuit Craft and scrapbooking projects (safe to use on Polystyrene)Areas where clamping or pressing facilities are either not available or difficult to use What materials is this product suitable for? Fabric Laminated plastics Veneers Hard board Polystyrene foam Fibrous cement sheet Aluminium Polyurethane foam Rubber Cork Leather Canvas Felt Metals Most plastics (Not recommended for bonding Polyethylene or Polypropylene Plastics, for these we recommend Plastics Glue ) How to use this product General bonding – use contact method or for small porous surfaces join with a wet bond by applying Kwik Grip Advanced to one surface only and immediately press together and lightly clamp. Kwik Grip Advanced can be used as wet bond on absorbent surfaces such as timber, cardboard etc. Contact bonding: 1 Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. 2 Using applicator provided with pack, completely cover both surfaces with adhesive and keep surfaces apart until the surface turns from white to clear – approx. 20 minutes. Tip: use dowels or something similar to keep surfaces apart 3 Position the items carefully, still keeping surfaces apart. When edges are perfectly aligned, remove dowels and working from one edge press surfaces firmly together. Note: Grabs IMMEDIATELY on contact. 4 Secure bond by running a roller over the bonded surfaces or by hammering the surface from the centre outwards using a padded block. Maximum Bond strength is achieved after 24 hours. Note: Drying time may be extended in cold and wet weather conditions. Wet bonding: Ensure surfaces to be bonded are clean, dry and free from dirt, grease, dust or particles. Apply to one surface then bring surfaces together and clamp until dry. Clean up application tools and excess adhesive with damp cloth & water before it dries. Handy tips What is a contact adhesive? A contact adhesive is an adhesive that must be applied to two surfaces and allowed to dry before surfaces are joined. Once surfaces are pushed together an instant bond forms. Therefore extended pressure or clamping is unnecessary (*Clamping of warped or curled surfaces may be required) Being Low VOC/low odour this product is much safer for use indoors than most other contact adhesives which tend to be solvent-based.. Can be used on horizontal or vertical surfaces In the event of prolonged open time, Kwik Grip Advanced will continue to give good contact bond for up to 8 hours. What does this mean? This means that once you have applied the adhesive, if you suddenly need to run out to the shops or go and do another job, you can safely come back within 8 hours and join the two surfaces for a great result! Many solvent-based contact adhesives have a much shorter open time limit.
$40.93
Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The Tip The Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The Adhesive Fix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors? A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor? A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area? A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck? A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool? A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe? A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor? A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill? A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes? A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly? A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$65.00
Note: To apply this product you will need a syringe Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble, stone & creaky wood floors without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The Adhesive Fix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the subfloor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors? A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor? A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area? A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble Stone & Loose Wood floors too! Q: Can I use Fix-A-Floor outside on my patio or deck? A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool? A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe? A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor on my creaky wood floors? A: Definitely! Fix-A-Floor works great on creaky, squeaky wood floors and laminate too! Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor? A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile or wood will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill? A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes? A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly? A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$85.00
Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The TipThe Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The AdhesiveFix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors?A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor?A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area?A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck?A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool?A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe?A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor?A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill?A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes?A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly?A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$384.45
High-Performance Multipurpose Wall & Floor Tile Adhesive This versatile adhesive is designed for fixing almost all tile types to a wide range of challenging surfaces, including water features and swimming pools. Key Features: Suitable for both walls and floors Can be applied over difficult surfaces, including water features Allows tiling over existing tiles Compatible with most types of ceramic and natural stone (excluding moisture-sensitive stone) Tile Types: Ceramic tiles Fully vitrified tiles Natural stone (excluding moisture-sensitive stone) Mosaics Porcelain Suitable Surfaces: Existing tiles Glazed ceramic tiles Metal Roughened fibreglass Timber (particleboard only) Application Areas: Walls and floors Indoor and outdoor Water features and swimming pools Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.4m²/kg 250 x 250mm and larger 10-12mm 0.25m²/kg
$49.42
This versatile adhesive is specially formulated for fixing most tile types, offering excellent flexibility and suitability for various surfaces. Key Features: Suitable for most tile types Can be applied over a variety of surfaces Suitable for interior timber (with proper preparation) Highly flexible Tile Types: Ceramic tiles Fully vitrified tiles Mosaics Porcelain tiles Natural stone (excluding moisture-sensitive stone) Suitable Surfaces: Cement render and concrete Fibre-cement sheets Existing ceramic and vinyl tiles Dunlop Undertile Waterproofing Metal surfaces Oil-based painted surfaces Plasterboard Indoor timber (must be adequately prepared) Application Areas: Walls and floors Indoor and outdoor use (as long as there’s no standing water and proper water run-off is ensured) Coverage: Tile Size Trowel Size Coverage Up to 250 x 250mm 6-8mm 0.8m²/kg 250 x 250mm and larger 10-12mm 0.5m²/kg
$37.86
An effective and easy-to-use neutral cleaner designed to remove general household dirt, grime, and oils from tiles and grout. Ideal for daily use, this cleaner is powerful enough to tackle grease in kitchens and bathrooms while being gentle enough for regular application. Key Benefits: Powerful cleaner for tiles and grout Effectively removes grease in kitchens and bathrooms Regular use reduces mould and mildew growth Suitable for general-purpose surface cleaning Cost-effective when diluted and applied by spray Easy to use for everyday cleaning Use On: Tiles, grout, and general household surfaces Surface Type: Walls and floors Location: Indoor and outdoor use Colour & Sizes: Size: 1L Item Code: 22504 Coverage: Wipe On: Dilute 10ml per 1L of water Spray On: Dilute 6ml per 1L of water Directions for Use: Test First: Before the first application of Dunlop Tile & Grout Cleaner, test a small amount of product in an inconspicuous area to ensure the desired result. Dilution: Mix 10mL of Dunlop Tile & Grout Cleaner per 1L of water. For best results, use hot water. Application: For general cleaning, apply the cleaner using a mop. For stubborn dirt, use an appropriate scourer or scrubbing pad that won't scratch the tile surface. Keep your tiles and grout clean and fresh with this powerful, easy-to-use cleaner, perfect for daily household maintenance.
$25.02
DUNLOP®WALL TILE ADHESIVE is a ready-mixed indoor wall tile adhesive. Ideal for all types of ceramic wall tiles and dimensional stones such as marble and granite, it can be used on a number of surfaces which include compressed fibre-cement sheets, plasterboard, cement render and adequately prepared painted surfaces (oil-based paint only). DUNLOP®WALL TILE ADHESIVE has superior flexibility and high grab to support even the heaviest of wall tiles. SURFACE PREPARATION Surfaces must be consistently flat and firmly fixed. Clean off dust, oil, grease and all loose contaminating materials or coatings. Ensure surfaces are dry, with no residue or permanent dampness. Prime porous surfaces (e.g. fibre- cement sheets, cement render) with DUNLOP®PRIMER & ADDITIVE beforehand and allow to dry. Cement Render Allow to cure for at least 7 days. Render should have a wood float finish. Plasterboard There is no need to prime the cardboard surface. However, where sheets are joined, DUNLOP®PRIMER & ADDITIVE must be used over the base jointing compound. Do not use the topping compound in areas which are to be tiled. Compressed Fibre-Cement Sheets Remove surface dust with a damp sponge and prime with DUNLOP®PRIMER & ADDITIVE and allow to dry before tiling. Painted Surfaces Oil-based paint should be roughened mechanically and loose flaking paint should be removed. Ensure the paint is suitable for tiling over. Thoroughly remove water-based paints. Do not use paint stripper or solvents. Allow surface to dry after cleaning. MIXING No mixing required. APPLICATION As a general guide use a 6mm notch trowel to spread adhesive achieving a minimum 1mm bed thickness. Do not wet tiles before fixing. If backs of tiles are dusty clean with a damp sponge. Spread the adhesive with the notches running horizontally across the wall. Spread only one square metre at a time and ensure a skin has not developed on the adhesive before bedding tiles. Press and slide the tile into position ensuring the whole of the back of the tile is in good contact with the adhesive. Use tile spacers if desired to ensure even spacing. Remove any surplus adhesive on face of tile or between joints before it sets. Adjustment of tiles should be carried out within 60 minutes of laying (at 23°C and 50% humidity). COVERAGE DUNLOP®WALL TILE ADHESIVE will cover approximately 0.5m2per kg. Coverage will vary depending on the condition of the surface being tiled and application technique. DRYING TIME DUNLOP®WALL TILE ADHESIVE will dry in approximately 24 hours depending on ambient temperature, porosity of surface and tiles. MOVEMENT JOINTS Incorporate movement joints at 3.5m intervals and at internal corners. Any structural movement joints must be carried through to the face of the tiling, at junctions between different background material and at fixtures interrupting the tile surface. These joints should be about 6mm wide and and kept free from adhesive. They should be filled with a high quality flexible material e.g. DUNLOP®COLOURED SILICONE. GROUTING Wait until adhesive has set. This takes approximately 24 hours. Remove tile spacers and use DUNLOP®GROUT adding DUNLOP®PRIMER AND ADDITIVE to enhance colour, impart a degree of flexibility and reduce porosity and staining. For easier maintenance seal with DUNLOP®GROUT SEALER. CLEAN UP While it is still fresh, DUNLOP®WALL TILE ADHESIVE can be cleaned off with a damp sponge. Tools, hands and material soiled with adhesive can be easily cleaned with water as long as the adhesive is still fresh. CAUTION Do not use DUNLOP®WALL TILE ADHESIVE to fix green marble. Do not use DUNLOP®WALL TILE ADHESIVE in continuous immersion applications e.g. swimming pools, tanks etc.. Do not use DUNLOP®WALL TILE ADHESIVE over non- absorbent substrates and waterproofing membranes due to prolonged drying times. DUNLOP GUARANTEE Product is guaranteed for 10 years when installed to manufacturers instructions. Manufactured under a quality system certified as complying with ISO 9001 by an accredited certification body. Material Safety Data Sheets are available TECHNICAL DATA Characteristics of product: Colour: White Viscosity: 790 000 cps S.G: 1.47g/cm3 pH: 9.1 Form: Viscous paste Application Properties: (@23°C and 50% relative humidity) Open Time: 80 mins Adjustability Time: 60 mins Mechanical Properties: Fundamental Characteristics Shear adhesion strength: Shear adhesion strength after aging: 2.5 Mpa (AS 4992.1) Minimum requirements 1.0Mpa (D1) 3.5 Mpa 1.0Mpa (D1) SAFETY Keep out of the reach of children. If skin contact occurs wash skin thoroughly with running water. If swallowed, give a glass of water and contact Poisons Information Centre. In case of contact with eyes, rinse with plenty of water and contact a Doctor. MSDS available on request.
$66.83
Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.
$59.48
High-Performance Ready-Mixed Ceramic Tile Adhesive This high-grab adhesive is designed to support even the heaviest wall tiles, providing superior flexibility for interior applications, particularly in kitchens and bathrooms. Key Features: Ready-mixed adhesive High grab for heavy wall tiles Superior flexibility Tile Types: Ceramic wall tiles Granite Marble (excluding moisture-sensitive stone) Suitable Surfaces: Cement render Fibre-cement sheets Painted surfaces (properly prepared) Plasterboard Application Areas: Indoor walls Coverage: 0.5m² per kg
$19.86
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$18.48
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
• Fluoride based formula controls slipping on ceramic, mosaic and quarry tiles, terrazzo and unpainted concrete floors • Alters surface texture yet maintains the appearance of the floor • Coverage: 10sqpm per meter
$69.20
The DTA Boss Grout Clean Up System Kit is a professional-grade cleaning solution designed to make post-grouting clean-up fast and effortless. Ideal for both tradespeople and DIYers, this all-in-one system helps you remove grout haze and residue from tiles after grouting. What’s Included: Heavy-duty cleaning sponge with handle High-capacity rinse bucket with roller Surface Preparation: Before use, ensure that the tiled surface has set appropriately based on grout manufacturer instructions. The grout should be partially cured but not fully hardened — typically 10–30 minutes after application. Remove excess grout with a rubber float before using this cleanup system. Application Instructions: Fill the rinse bucket with clean water up to the indicated level. Use the included sponge to gently clean the surface in a diagonal motion. Rinse sponge regularly by rolling it over the inbuilt rollers to remove grout particles. Repeat the process until the grout haze is removed and the tile surface is clean. Coverage: Cleans up to approximately 25–50m² per fill depending on tile texture and grout thickness. Drying Time: Tiles are generally clean and dry within 30–60 minutes of cleanup depending on ambient temperature and humidity. Ensure proper ventilation for best results. Clean-Up: Empty the bucket, rinse the sponge and components with clean water. Dry thoroughly before storing to extend product life. Technical Data: Rollers: Dual high-strength plastic rollers Sponge: Extra absorbent and replaceable This system is compatible with most grout types including cementitious and epoxy grouts. For stubborn epoxy residue, use in conjunction with a suitable epoxy grout cleaner.
$209.48
Davco® Tile & Grout Cleaner is specially formulated to tackle tough dirt and stains from tiles and grout. It’s also effective in removing minor efflorescence, making it a versatile cleaner for common tiled surfaces. Key Benefits: Specially formulated ingredients Effectively cleans tiles and grout Removes minor efflorescence from grout Helps remove mould and mildew from grout surfaces Usage: Davco® Tile & Grout Cleaner is suitable for a wide range of tiled surfaces, including: Ceramic Porcelain Mosaic Quarry Slate tiles It’s ideal for removing tough dirt and stains from tiles, as well as refreshing aged grout. Packaging: Size: 1 Litre Jerry Can Colour: Clear liquid Application Steps: Mixing: Dilute Davco® Tile & Grout Cleaner with water in a clean plastic bucket at a ratio of 10 parts water to 1 part cleaner (e.g., 5L of water to 500ml of cleaner). Application: Prepare the Surface: Always wet the surface with clean water using a mop or sponge before applying the product. For Normal Cleaning: Dampen a mop or sponge with the diluted solution and wipe over the surface, then immediately rinse with clean warm water. For Heavily Soiled Areas: Apply a larger quantity of the solution and allow it to soak for up to 10 minutes. Scrub the affected area with a stiff nylon brush, then rinse thoroughly with clean warm water. Keep your tiles and grout clean, refreshed, and free from tough stains and minor efflorescence with Davco® Tile & Grout Cleaner.
$33.54
You have seen 144 out of 162 products
Products suited to kitchen environments. Choose sealants, adhesives and accessories that match moisture, temperature and movement demands in kitchen areas. Look for mould resistance, flexibility, UV stability or potable‑water suitability where shown. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
