![Selleys Armour Flex High Performance Adhesive [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
![Selleys Armour Flex High Performance Adhesive [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125293_a1f282bb-e154-4d4c-812a-1cc8034e1e80.jpg?v=1754711935&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$23.14
![Selleys Armour Flex High Performance Adhesive [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125286_24a1028f-4655-4200-8859-8e45b8c9ab19.jpg?v=1754711936&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
A new high-performance epoxy adhesive that applies to wet or dry surfaces for complete waterproof bonding. Trust Selleys Aqua Fix to stick when wet – even underwater Features Can be applied to wet and dry surfaces 100% Water resistant Use on multiple surfaces Strong durable bonding Sticks and sets underwater Withstands thermal and mechanical shocks Temperature range -15°C (continuous) to +80°C (intermittent) Colour Dries off white What materials is this product suitable for? Tiles Metal Timber Rubber China Glass Leather Most plastics (not for polyethylene, polypropylene) How to use this product Ensure surfaces to be bonded are clean, free of grease, dirt and lose materials. For best results roughen bond area, prior to cleaning. Carefully cut the sealed tips at the end of the syringe nozzle. Dispense equal parts onto a clean disposable surface and mix together thoroughly to a uniform colour. Mixed glue remains usable for 1 hour. Apply mixed glue to both surfaces of the job then bring together. Do not apply undue strain to bond for 6-8 hours. Hold joint in place using tapes, clamps or weights if necessary for 24 hours. When applying underwater ensure mixed glue is pushed onto the surface firmly until the glue displaces water and adheres to surface. Handy tips For Aquariums allow to cure for at least 72 hours, then thoroughly wash out with water, drain and refill before introducing fish. Not approved for contact with drinking water – use Selleys Knead-It Aqua. Storage and re-use Place cap from plunger on the nozzle for storage Clean up uncured Aqua Repair Glue with acetone (nail polish remover) Safety tips KEEP OUT OF REACH OF CHILDREN Avoid contact with skin and eyes Avoid breathing vapour Wear eye protection and protective gloves when mixing or using. This product is classified as hazardous. Avoid contaminating waterways with uncured product. For frequent hobby or occupational use, refer to the Safety Data Sheet for more information before using the product.
$22.00
$40.16
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$16.93
Selleys 655 FC Crystal Clear Flexible Adhesive and Sealant 290 mL Premium 100 percent crystal clear hybrid adhesive and sealant that delivers superior strength, instant grab, and long lasting flexibility. Bonds and seals on most common building materials, works indoors and outdoors, and can be applied to wet or damp surfaces. Low VOC, non yellowing, paintable, and non slumping for neat vertical and overhead joints up to 20 mm. Why you will love it Superior strength with instant grab Primerless adhesion on most surfaces Applies to wet or damp substrates Fast curing with non slumping finish Crystal clear appearance that stays clear Low VOC and isocyanate free Paintable with water based paints Suitable for interior and exterior use Where it works Ideal for sealing, bonding, and filling on concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, fiberglass, and most plastics. Not recommended for polyethylene, polypropylene, or PTFE. Typical applications Clear sealing of kitchen and laundry splashbacks Bonding trims, panels, and skirtings Sealing gaps in windows, door frames, and cladding General construction and maintenance sealing where a clear finish is desired How to use Prepare the surface so it is clean and free from dust, grease, and loose material. Cut cartridge tip, attach nozzle, and load into a caulking gun. Cut nozzle to the required bead size. Apply a continuous bead, pressing firmly so the product contacts both sides of the joint. Tool with a soapy solution before skinning. For neat edges, mask before applying and remove tape before skin forms. Clean up Uncured product cleans off with mineral turps. Once cured, remove by scraping or sanding. A dedicated silicone and adhesive remover can assist. Good to know Do not paint with solvent based paints. If painting, first coat with a water based paint. Not suitable for permanent water immersion or below water line use. Store below 30°C. Use within 6 months after opening for best results. Specifications Technology Moisture curing silyl modified polymer Colour Clear Pack size 290 mL cartridge Density Approx. 1.06 g/mL Application temperature 5 to 35°C Tooling time at 23°C and 50 percent RH About 25 minutes Skin time at 23°C and 50 percent RH About 45 to 55 minutes Cure rate at 23°C and 50 percent RH Approx. 3 mm per 24 hours Slump 0 mm Tensile strength About 1 MPa Shore A hardness 30 ± 5 Elongation at break Approx. 130 percent Modulus at 100 percent elongation About 1.0 MPa Service temperature 0 to 70°C VOC content Approx. 35 g/L Safety Follow good ventilation and hygiene practices. Refer to the product safety data sheet for detailed advice.
$20.00
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$20.00
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$16.52
Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 1.2 cm Overall Width (Metric) 5 cm Product Colour Black Product Type Rolls Size 5cm x 1.2m Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$17.19
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$14.24
Easily mount signs, plaques or house numbers using the Scotch™ Mounting Strips. They are weather resistant and can be used both indoor and outside. Your solution for a long lasting strong bond. Holds up to 2.7kg, 7.6cm holds 340g Mount a sign, mailbox or plaque without needing to use nails or screws Ideal for Indoor and Outdoor surfaces and applications Recommended Surfaces: Painted wood, painted bricks, metal, vinyl Uses 3M VHB™ Tape Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm
$8.81
Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$11.29
![RiteTack Instant Grab Construction Adhesive 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/0799439671669_6c8563d0-64cb-499e-a564-d2d4a62e9ce2.png?v=1754712007&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/0793591712994_c9bef70a-42d0-408c-8b14-e176578d110d.png?v=1754712009&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/0793591712987_0ace0873-9628-42fc-9b06-c64c93c74c40.png?v=1754712010&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
An all purpose, high strength household glue that unlike standard superglues is extremely ‘infinitely’ more flexible. It can repair and bond a variety of surfaces and withstand the most extreme/rough conditions whilst providing the ultimate bond. Features Strong Bond Ultra Flexible – infinitely more flexible* Extreme Resistance to: Shocks & Vibration, Torsion & Movement, Water and Extreme Temperatures Dishwasher Safe Gap Filling (works on uneven surfaces) Paintable Adjustable for 1min Non-Drip (great for vertical surfaces) Interior/Exterior Easy to use Heat resistant -15°C to +120°C Solvent free, no shrinkage Colour Dries translucent What materials is this product suitable for? Metal Wood Glass Rubber China Leather Ceramics Masonry Fibreglass Vinyl Cardboard Fabric Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place Safety Tips On contact, uncured adhesive can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice. Avoid contact with skim. If contact occurs, wipe off and wash with detergent. Avoid breathing vapours. Use in a well ventilated area
$12.00
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$19.17
A two-part gap filler and binder for builders and tradesmen that is a safe alternative to the toxic solvent and styrene-based fillers and bogs on the market. Environmentally friendly and non-hazardous for safe handling and easy transport Easy to mix, spread on rough and smooth substrates immediately Rapidly sets in 15 mins (faster in warm weather) with minimal shrinkage Curing time approximately 60 minutes • Long shelf life when firmly sealed after each use Once cured it may be chiselled, filed, sawn, planed and sanded into shape Can also be nailed, drilled, screwed, glued and painted Highly recommended for waterproofing as gap filler for bathroom renovations and other wet area applications where tiling or painting is required
$24.90
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$7.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$13.50
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$169.39
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$50.78
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$6.07
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$112.76
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$8.30
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$17.04
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$15.16
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$13.35
A powerful long-lasting mould inhibitor (when added to an existing product e.g. paint) which inhibits the unsightly growth of mould on to the surface it is applied to. Mould Defence forms an enduring film that will not change the look or feel of the substrate to which it is applied. Mould Defence is recommended to be used in areas where high moisture is present e.g. bathroom, laundries and kitchens, however, for peace of mind, can be used throughout the whole house. Mould Defence can be added to a wide range of products including paint (water based and solvent), timber oils/stains, textured coatings, grout, mortar and adhesive. Add 5mL per L of paint/stain/oil or 5mL per Kg of RTU product.
$22.18
Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!
$4.00
There's a lot of grime to be wary of in this world, and there's no reason you should have to put up with it. Prep marathon gets your day off on the right foot by getting your house clean as a whistle again. Reach out today for this hardworking citrus-based cleaner that intensively degreases stubborn messes and is tough enough to tackle kitchen grease spills with ease. And because we use non-petroleum solvers, our lotions are less drying than most brands while still being gentle on hands. Get Prep Marathon Re-Moove-It Cleaner now!
$6.00
Clean your outdoor glass surfaces consistently! Little clumps of dirt and debris can dirty your windows within moments. For easy, efficient, and quick clean-up have the Prep Marathon Outdoor Glass Click & Spray handy. It's formulated to easily dislodge tough dirt over time with innovative technology. The click feature is perfect for those who are unable to stand for extended periods of time.
$7.00
Prep Marathon is the perfect product for anyone who hates dirtying their hands when cleaning. Our BBQ cleaner combines hunger and cleanliness with a fresh scent to leave your dishes shining like new. When it comes to cooking, this easy prep option is ideal for making sure all of popsicles have made it into mouths safely- but also neat enough to make your house feel like royalty after you're finished!
$4.00
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$25.00
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$9.00
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$175.00
Outdoor Timber Polish is made from natural plant oils & fragrance oils. Covers scratches, removes stains & preserves wood. • Nourishes, restores and protects outdoor furniture and woodwork. • Specifically formulated to suit Australian and New Zealand conditions. Coverage: Up to 20m2 per L Apply with: Mist on, wipe in with rag 24 hours recoat Sheen Level: Transparent Matt finish
$16.56
Specially developed for filling cracks & dents on doors, windows, trim, architraves and skirting boards, sanding to a smooth, hard mirror like finish. The perfect preparation for gloss paints. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Plasterboard, concrete, timber & primed metal (INTERIOR & EXTERIOR) Fill depth: Up to 3mm Dries in: 3 hours Ready to use: YES Available in: 330mL & 770mL Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Using the attached filling blade press filler in firmly and remove excess. * Allow to dry for 2-3 hours in thin 2-3mm applications, depending on humidity. Allow longer drying times if painting with oil based paint and for deeper applications. • Sand with fine sandpaper. For a perfect finish after initial sanding back, apply another very thin coat of filler, allow to dry and sand lightly with very fine (400grit) sandpaper before painting. • Protect from rain until painted over. • Not for exterior timber likely to absorb excessive amount of water. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Why should I use a specialised filler under gloss paints? A. Gloss paints show up every flaw and bump on surfaces. Therefore, a specialised filler that ensures an extremely smooth, hard, "glass-like" finish is preferred for the ultimate flawless, flat surface. Polyfilla Trim and Doors is the ideal filler under gloss paints. It also gives perfect gloss retention so you won't notice a 'dull' spot under the paint. You should also apply an undercoat before the final coat of paint for the best results.
$18.94
Polyfilla Rapid 30 100g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 100g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 100g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$12.35
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$46.19
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$11.74
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$84.97
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$29.00
A ready-mixed filler that dries hard to a durable finish for deep and wide cracks in mortar, concrete, cement render and brick. Water, weather, UV, algae and mould resistant Can be tooled to a render texture or sanded to a smooth finish. For use on: Bricks, concrete, bare or painted cement render & other masonry surfaces (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: Cement grey in colour but can be painted over with both oil and water based paints • Ensure surfaces are clean and free from dust, grease, mould/algae and flaking/powdery paint or material. If necessary wash with Poly Sugar Soap. • Rinse thoroughly and allow surface to dry. • Use flexible filling blade to press filler into hole, or trowel to spread a thin layer over surface, and tool to a feathered edge. • Allow to dry (2–3 hours in thin 2–3mm applications, depending on temperature and humidity) before sanding and painting. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. • Protect from rain until dry. If required, paint with a quality exterior coating. • For a render texture smooth out with trowel or filling blade when applying the product and do not sand. For a smoother texture sand surface after drying. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$83.99
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing. Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out. Can be stained, clear-finished, painted, nailed, screwed, sanded or planed. For use on: Timber (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Available in: 450g and ^2kg Colour: Dries to a pine colour NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc. • Ensure surfaces are clean and dry. • Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary. • Apply firmly with filling blade. • Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity). • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish. • For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing. • Protect from rain until painted over. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$22.49
A durable, ready to use, acrylic based, flexible filler for filling cracks, holes, dents and splits in weatherboards and other exterior woodwork such as decking and fencing. Unlike more rigid woodfillers, it flexes with the natural movement of wood and will not crack, split or fall out. Can be stained, clear-finished, painted, nailed, screwed, sanded or planed. For use on: Timber (EXTERIOR & INTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: Dries to a pine colour NOTE: Not for permanently wet areas or joints between weatherboards, floorboards, panels etc. • Ensure surfaces are clean and dry. • Remove any rotten wood and fix split timber firmly before filling. Priming is unnecessary. • Apply firmly with filling blade. • Allow to dry (*2–3 hrs in thin 2–3mm applications depending on humidity). • For deeper jobs apply in 10mm layers, allowing each layer to dry before applying the rest. Allow longer drying times (24 hours minimum) if painting with oil based paints, for deeper applications or in colder weather. • Sand back and paint with with a quality exterior water or oil-based paint, or stain and clear finish. • For a smoother finish allow filler to dry, sand back and apply a very thin coat of filler. Allow this to dry then sand lightly with fine (>300 grit) sandpaper before painting or vanishing. • Protect from rain until painted over. • For best results, apply undercoat before applying water or oil based top coat. • Where joint movement occurs, use a flexible Poly sealant. • Clean up with water before filler dries.
$79.79
A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$21.60
You have seen 336 out of 428 products
Products suited to outdoor environments. Choose sealants, adhesives and accessories that match moisture, temperature and movement demands in outdoor areas. Look for mould resistance, flexibility, UV stability or potable‑water suitability where shown. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
