In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Liquid Nails Flex is a flexible construction adhesive built for jobs that need a strong, lasting hold that can still move. It is designed to stretch a long way under load while keeping its grip, so bonded materials can expand, contract and shift with the building without the join letting go.What it isA high-performance, low-VOC construction adhesive that bonds to most common building materials, porous or non-porous, and will even grab onto damp surfaces. It cures quickly, shrugs off everyday movement and wear, and stays paintable once set.Where to use itIndoors: fixing skirting, architraves, trims, panelling, plasterboard, tiles and general carpentry where a bit of flex is wanted.Outdoors: exterior trims, cladding and general building repairs, thanks to its interior and exterior rating and weather resistance.How to use itCut the nozzle and load the cartridge into a standard caulking gun. Run a continuous bead along studs, joists or battens, or space beads roughly 5cm apart on broad surfaces. Bring the surfaces together within about 10 minutes and brace, clamp or fix mechanically. Leave temporary fasteners in place for at least 4 hours, and use mechanical fixings for high-stress work.Important notesDo not rely on it as the sole support in structural or overhead applications, and avoid tightly clamped joints. Wipe up uncured adhesive with mineral turpentine; once cured it is removed by scraping or sanding.Specifications
Brand
Selleys
Range
Liquid Nails
Product
Liquid Nails Flex
Size
430g
Type
Flexible construction adhesive
Stretch
Up to 400%
Gap fill
Up to 9mm
Standard
Meets AS 2753 gap filling
VOC
Low VOC (under 50 g/L)
Use
Interior and exterior
Clean up
Mineral turpentine
SafetyUse in a well-ventilated space and avoid prolonged skin contact. Keep out of reach of children. Always read the current Selleys Safety Data Sheet for full handling, first aid and disposal guidance before use.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop FC Joint Sealant
Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey.
Why choose this sealant
High flexibility for dynamic joints
Non slump for clean, accurate beads on vertical and horizontal surfaces
Solvent free and isocyanate free
Paintable after curing
Reliable performance supported by a 10 year guarantee
Ideal uses
Joints in fibre cement, blueboard and compressed fibre cement sheets
Facade and cladding joints where movement is expected
General building joints up to 40 mm width
Compatible surfaces
Adheres to most common construction substrates, including:
Fibre cement sheets and blueboard
Precast concrete panels, blockwork and bricks
Sandstone and granite
Fibreglass
Plasterboard
Technical details
Movement capability
± 25%
Joint width
Up to 40 mm
Skin time
Approximately 35 minutes at 23°C and 50% RH
Tack free time
Approximately 1 hour at 23°C and 50% RH
Cure rate
About 2.5 mm per 24 hours at 23°C and 50% RH
Application temperature
10°C to 35°C
Clean up
Warm water immediately after use
Shelf life
12 months unopened, stored cool and dry
Finish
Paintable when dry. Can be overcoated with paint or texture coats.
Colour
Grey
Surface preparation
Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer.
How to apply
Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width.
Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width.
Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides.
Curing times increase in cold or humid conditions.
Safety and handling
Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance.
Guarantee
Backed by a 10 year guarantee when used as directed.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish.
Uses
Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous.
Typical applications include:
Areas where nailing is not desirable
Skirting boards, architraves, and cornices
Wall panelling to masonry
Styrene foam to metal roofing
Technical Features
Fast grab – high initial holding reduces slippage on vertical surfaces
Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards)
Non-drip formula – does not sag or string between panels
Bridges gaps and adheres to uneven surfaces
Low mess – excess can be wiped away with a damp cloth
No solvent fumes – ideal for indoor projects
Flexible – withstands thermal movement and vibration
Heat resistant – maintains bond strength under sunlight
Paintable when dry
Easy to extrude in all temperatures
Application Tips
Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures.
Bonds are not water resistant – protect from water if used outdoors.
Drying time is extended in cold or damp conditions and with non-porous materials.
Thicker layers take longer to dry.
Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene.
For wood flooring, use solvent-based Liquid Nails instead.
Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors.
Technical Details & Performance
Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days.
Appearance: Smooth beige paste, free from lumps and air bubbles
Specific Gravity: Approx. 1.44 g/mL @ 25°C
Viscosity: 7000–9000 Poise
Slump: 0 mm (typical)
Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate)
Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329)
Initial Bond Strength (24 hrs): >200 kPa
Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power.
Creep Resistance (under constant load):
– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area
– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area
Coverage
Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use.
Cleaning
Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling.
*Always pre-test plastics for adhesion suitability.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
UNi-PRO Cornice Adhesive 2.5 kg
Overview
UNi-PRO Cornice Adhesive 2.5 kg is a high quality cornice adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework.
Why choose this product
Reliable bond performance supported by proven chemistry and rigorous quality control.
Smooth, predictable application that helps reduce mess and cleanup time.
Versatile adhesion profile suited to a wide range of substrates and project types.
Clear guidance on surface preparation, application method, and curing to help achieve the best possible result.
Suitable for residential fit-outs, maintenance, repairs, and light commercial projects.
Suitable materials
plaster cornice
plasterboard
masonry
Typical applications
General installation, repair, and maintenance where a durable bond is required.
Interior work that benefits from a neat finish and tidy joints.
Projects where dependable initial grab and high final strength are important.
Surface preparation
Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting.
Application
Check ambient and substrate temperature. Apply between 10°C and 30°C in dry, draft free conditions.
Cut the nozzle to the required bead size or prepare the container according to the product type.
Apply an even bead or spread with a suitable trowel where required. Avoid trapping air.
Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting.
Support, clamp, or brace as needed until the adhesive develops sufficient handling strength.
Cure and working time
Sets firm to hold cornice in place, full cure over 24 hours or as directed. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure.
Coverage
Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces.
Limitations
Do not apply to surfaces that are visibly wet unless the product specifically allows damp application.
Avoid continuous water immersion unless the product is rated for that exposure.
Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required.
Observe maximum service temperature and any movement or vibration limits appropriate to the application.
Clean up
Wipe away fresh adhesive with a damp cloth. Scrape away set material carefully. Always read the product label and follow local regulations for disposal of leftover material and containers.
Safety
Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. Do not ingest. Refer to the Safety Data Sheet (SDS) for full details.
Storage
Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first.
Troubleshooting
Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure.
Slow cure: Verify temperature and humidity. Increase airflow or allow more time.
Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins.
Frequently asked questions
Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first.
Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured.
What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat.
How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes.
Why buy from Glues Australia
We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond High-Strength Foam Construction Adhesive 750 mL is a reliable one component foam construction adhesive dispensed from a can chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 750 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Sika High-Strength for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. SikaBond High-Strength Foam Construction Adhesive 750 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Fixing studs, battens, and sheets
Filling small gaps while bonding
Fast installation where speed saves labour
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Timber and masonry
Concrete and fibre cement
Many building materials except PE and PP
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of assemble parts within the open time to ensure a strong bond. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Expands slightly to fill gaps, then cures to a firm, high strength foam. Provides excellent initial grab and reduces the need for nails in many applications.
Temperature and environmental performance
Apply within the can's specified temperature range. Humidity supports foam curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean uncured foam with the prescribed cleaner. Once cured, cut back mechanically. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store cans upright. Do not expose to heat. Observe transport and disposal rules for pressurised containers. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion High-Bond Stud Adhesive 5.2 kg is a reliable stud adhesive for fixing plasterboard to timber or metal framing chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 5.2 kg pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Bastion High-Bond for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Bastion High-Bond Stud Adhesive 5.2 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Plasterboard installation on studs
Reducing screw count by bonding and fixing together
Renovations where clean bond lines are important
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Timber studs
Galvanised metal studs
Plasterboard back surfaces
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of work within the wet time window to ensure transfer. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Applies as a bead to studs. Press board into place and fix with screws while the adhesive is wet. Final cure occurs as the solvent or moisture leaves the bead.
Temperature and environmental performance
Use in dry, shaded conditions during lining work. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Remove fresh smears with a suitable cleaner. Trim cured squeeze out before finishing. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store closed and away from heat sources. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts.
Key features
Fast setting gel for controlled application
Non drip formula for vertical and overhead surfaces
Small gap filling for close fitting parts
Strong bond on many common materials
Clear finish for neat repairs
Ideal for
Metal, rubber, most hard plastics, wood, ceramics, porcelain
Small household repairs, models, craft and DIY fixes
Precision bonding where liquid super glue may run
Not suitable for
Polyethylene, polypropylene, PTFE
Very flexible materials or items regularly exposed to water immersion
Food contact surfaces or aquarium use
Directions
Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible.
Remove cap and apply a small bead of gel to one surface. A little goes a long way.
Join parts immediately and hold firmly until set. Avoid moving the bond during curing.
Allow the repair to rest for several minutes before light handling and longer for full strength.
Handy tips
Test on an inconspicuous area first.
Use sparingly. Excess adhesive can slow cure.
For porous materials, a second application may improve the bond.
Clean up
Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure.
Storage and safety
Close cap tightly after use and store upright in a cool, dry place.
Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart.
Use in a well ventilated area and keep out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects.
Why you will love it
Strong, long lasting bond
Dries clear for a neat finish
Water resistant once fully cured
Flexible bond helps absorb vibration
Suitable for indoor and outdoor use
Works on
Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first.
Ideal for
Household repairs and DIY
Craft, hobbies, and school projects
Fixing ornaments, toys, trims, and fittings
Directions
Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces.
Apply a thin even layer to one surface.
Join parts together and press firmly. Support or clamp if needed.
Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate.
Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity.
Clean up
Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping.
Good to know
Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion.
Avoid contact with food or drinking water surfaces.
Store upright in a cool dry place with cap tightly closed.
Key details
Brand
Bostik
Product
Repair All
Appearance
Clear when dry
Finish
Flexible
Water Resistance
Yes, once cured
Pack Size
20ml
Always read the label and follow safety instructions. Keep out of reach of children.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SikaBond is a high strength contact adhesive that will not slump on vertical surfaces. It can be used as a one way liquid adhesive, or a two way contact adhesive, on a variety of surfaces.
Uses SikaBond can be used on most substrates due to its excellent adhesion.
These include:
Floor and wall panels.
Wood, plasterboard and chipboard.
Aluminium, iron and steel.
Concrete, cement sheeting and masonry.
Advantages
One component ready to use.
Fast drying time.
Easy to use.
High adhesion strength.
Non-slump.
Storage and Shelf Life
Stored in the original sealed packaging at temperatures of between 5ºC and 35ºC, this material will keep for at least twelve (12) months.
Instructions for Use
Surface Preparation All surfaces must be clean, sound, dry and free of oil, grease and surface contamination. Thoroughly remove all loose particles and dust. Any loose flaking must be removed and light sanding is recommended.
Application
One Way Method:
This method is recommended for heavier panels or where load or stress is expected. Apply a 4 to 6mm bead of SikaBond using a cartridge gun, making sure the beads are no more than 45cm apart. Bring both substrates immediately together and clamp, nail or screw for a minimum of 24 hours. For butt joints use adhesive on both panel edges.
Two Way Method:
Apply adhesive as in one way method, bring together substrates, and press firmly over entire surface to transfer adhesive. Then pull apart. Allow adhesive to tack off for 3 to 5 minutes depending on weather conditions, reposition the objects and press together firmly. The surfaces should be tapped together with a hammer and a padded block to ensure maximum contact. Maximum bond strength will be achieved in 12 to 72 hours, depending on substrates and weather. Heavy panels may require temporary mechanical fastening until maximum strength is achieved.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
High strength, structural grade polyurethane adhesive sealant
High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress
Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings
Vibration dampening
USE
Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics.
CHARACTERISTICS AND ADVANTAGES
1-C formulation
Elastic
Can be overpainted
Good gap-filling properties
Capable of withstanding high dynamic stresses
Vibration
Damping
Non-corrosive
Electrically non-conductive
Bonds well to a wide variety of substrates
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge.
Features
Sticks and withstands virtually anything*
Outperforms Super glue on uneven, porous or non-rigid surfaces.
Shockproof – bends on impact
High flexibility
High bond strength
Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly.
Water & Weatherproof
Temperature Resistant 15C – 120C
Dishwasher Safe
Works on uneven surfaces
Set time 3 minutes
Colour
Dries clear
What materials is this product suitable for?
Metal
Wood
Stone
Bricks
Concrete
Masonry
Ceramic
Glass
Foam
Leather
Laminate
Vinyl
Fabric
Cardboard
Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue)
How to use this product
Use in a well-ventilated area
Ensure surfaces are clean and dry. Remove cap and apply to a surface.
Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics).
If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours.
Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place.
Clean up before adhesive sets with turps or acetone.
Handy tips
Initial bond in 3 minutes, full cure in 12-24 hours.
To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together.
Safety Tips
Causes skin irritation. May cause an allergic skin reaction.
Causes serious eye damage.
KEEP OUT OF REACH OF CHILDREN.
Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area.
Wash thoroughly after handling.
Product releases methanol during cure.
Storage and re-use
Wipe nozzle clean, replace cap & store in a cool dry place.
*Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home.
Easy to sand, sets to a super hard finish and is highly crack resistant.
For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR)
Fill depth: Up to 10mm
Dries in: 3 hours
Ready to use: YES
Colour: White
• Surface to be filled should be clean and dry with no loose or powdery material.
• Exterior surfaces and metals (eg. nail heads) should be primed before application.
• Using the filling blade press filler in firmly and remove excess.
• Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications.
• For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer.
• Protect from rain until painted over.
.• For best results, apply paint undercoat before applying water or oil based paint top coat.
• Use Polyfilla Gap filler or silicone sealant where joint movement occurs.
• Clean up with water before filler dries
Q. Is there a filler I can use for both inside and outside?
A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Hold It Australia T77 STUDLOCK
High Strength for Bolts 25mm and Above - 50ml
Description: HOLDIT AUSTRALIA T77 Studlock large diameter high strength threadlocker is a red, general purpose adhesive for permanent threaded assemblies. It effectively locks fasteners 1 and larger in diameter, providing a seal against leakage and corrosion while resisting attacks from lubricants and industrial liquids and gases.
Applications
Ideal for eliminating double nutting/welding in critical assemblies. T77 allows for reduced casting thickness and prevents cracked castings from interference fit stresses. Suitable for larger diameter studs with coarse threads and can be used to reclaim worn stud holes. Primers are recommended for large gaps and poorly fitting parts.
Instructions for Use
Clean all surfaces with a cleaning solvent and allow to dry.
If the metal is inactive or the cure speed is slow, apply HOLDIT AUSTRALIA AA471 Activator or AA649 Accelerator.
Shake the product thoroughly before application.
Apply the adhesive to the fixing position of the fastener or onto the internal threads of a blind hole.
Assemble components and tighten to the required torque level.
Allow the adhesive to fully cure before applying load.
Active & Inactive Metal Table
Active Metals (Fast Cure): Iron, Steel, Nickel, Aluminium
Inactive Metals (Slow Cure): Stainless Steel, Titanium, Zinc, Anodized Aluminium, Galvanised Steel
Passive Surfaces (Primer Necessary): Ceramics, Glass, Plastics, Painted Surfaces
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever
Product Overview
Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing.
Smart Advantages
Extremely high initial tack
No fixation or support needed during curing
Free of isocyanates, phthalates, solvents, and silicones
Suitable for both interior and exterior use
Non-corrosive towards metals
Almost odorless
Resistant to moisture, weather, and UV
Applications
Universal bonding adhesive suitable for:
Stone, Concrete, Glass
Metals, Alloys, Stainless steel
Plastics, Polyurethane, PVC
Wood, Paint Systems
Directions for Use
Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength.
Limitations
Not suitable for certain plastics, continuous water exposure, or movement joints.
Cleaning & Safety
Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed.
Product Codes & Specifications
Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Nail It Fast Cure White: The Acrylic Adhesive for Rapid, Strong & Odorless Bonds
Product Overview
Bostik Nail It Fast Cure is a fast-curing, versatile acrylic adhesive that offers strong and durable bonds. It's easy to apply and almost odorless.
Key Benefits
Solvent-free formula
Suitable for EPS and XPS
Non-corrosive towards metal
Easy to apply and clean
Applications
Specifically developed for bonding:
Wood, chipboard, hardboard
uPVC to brickwork, stone or concrete
Ceramic tiles to porous substrates
Limitations
Not suitable for PE, PP, PC, PMMA, PTFE, soft plastics, neoprene, and bituminous substrates. Not designed for continuous exposure to water or for movement joints.
Application Instructions
Apply the adhesive in a ventilating manner, using vertical stripes or dots. Material should be placed by shoving and pushing firmly.
Surface Preparation
All substrates must be solid, clean, dry, and free from grease and dust. For porous substrates, priming may be required.
Cleaning & Maintenance
Tools and uncured material can be cleaned with water or Methylated Spirit. Cured material must be removed mechanically. Bostik HANDY WIPES are recommended for cleaning hands.
Colour Options
Available in white.
Thixotropic or expanding systems that bridge uneven joints and larger voids. Balance gap-fill with cure-through depth and final strength. Use filters to refine by chemistry and working time. Always check the product page and TDS/SDS.
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-252-high-strength-structural-adhesive-sealant-white-2.jpg?v=1792406508&width=645)
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](//gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White] (2)](//gluesaustralia.com.au/cdn/shop/files/sika-sikaflex-252-high-strength-structural-adhesive-sealant-white-2.jpg?v=1792406508&width=645)
