Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand Use: Suitable for indoor filling and repair where thicker filling capability is needed A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting Features Ready to use, no mixing required Easy application Thick layer filling and levelling ability High initial tack or grab on plaster and concrete Quick drying Colour: Grey
$20.57
Sil-X advanced polymer technology is formulated to deliver superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Sil-X has been specially developed to withstand the tough Australian and New Zealand conditions. Selleys THE ONE Adhesive delivers superior bond strength on any building surface. Can be applied to wet or dry, interior or exterior, porous or non porous surfaces*. Extreme versatility that takes the guess work out of DIY. Features Strong bond on any building material Can be applied to wet or dry surfaces Suitable for interior and exterior applications Can be used on porous and non-porous materials Will adhere to oily surfaces Low VOC Excellent weather resistance Flexible and long lasting Paintable with water-based paints What materials is this product suitable for? Suitable for all building materials* How to use this product Ensure surfaces are clean and free from grease or loose particles. Cut tip of cartridge, fit nozzle and cut at 45ºangle to desired size before placing in a cartridge gun such as Selleys Light Speed Caulking Gun. Apply with a caulking gun, pushing adhesive onto the surface. Position pieces and press firmly together. Larger, heavier materials may need to be supported until the adhesive cures. If painting, paint with water-based paint. Handy tips Keep a pack of SELLEYS Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job. Limitations *Not for PE, PP, PTFE, or permanent water immersion Clean up Clean up with turps before the adhesive cures. Safety tips Keep out of reach of children. Avoid skin and eye contact and breathing vapours. Use in a well ventilated area. Wear protective clothing, gloves and eye protection. If on skin, wash with soap and water. Cure product before disposal. Product releases methanol during cure.
$17.00
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safety tips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If in eyes, wash out immediately with water. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Additional information is provided in the Safety Data Sheet.
$19.00
Selleys Special Putty is a Linseed oil based, knife grade putty available in a natural colour. Features Easy to use. Can be applied by hand or with a putty knife Product has exceptional keeping qualities Available in a natural colour Superior grade putty Where can this putty be used? A wood sash putty that is excellent for glazing wooden windows and doors Bedding glass beads Not recommended for use with heat absorbing glass If being used in external applications it is not recommended for use with timber stains, timber oils and clear finishes Not recommended for use where structural movement may occur Not recommended for use in metal framed windows. What materials is this putty suitable for? Wood Timber How to use this product Rebates and grooves should be rigid, free from distortion, true and square, and should be clean, dry and unobstructed before glazing. Rebates and grooves should be of a size which allows adequate edge cover and putty volume. Minimum bed putty – 2mm, minimum front putty – 4mm where timber beads are used, and 2mm bed putty and 12mm front putty where no glazing beads are used. Depth of rebate: 10mm for 3-4mm glass, 15mm for 5-8mm glass. Two coats of good quality house paint should be applied not less than 2 weeks and not more than 4 weeks after completion of glazing. Paint should be carried out 2mm above the top line of the putty. Handy tips Do not use kerosene, turps or other material to aid in working the putty Allow putty to skin before applying paint Product can be applied by hand or with a putty knife. Add a few drops of linseed oil on the hands or knife to make for easier working Putty can thicken in cold weather. Warming the putty by working it in the hands before the application will soften it. Putty must be painted in exterior applications. High humidity, cold weather and use in interior applications can extend skinning times. Putty can separate on prolonged standing. If excessive oil is observed on the surface try to work the entire mixture together to redistribute the oil. Before painting, clean and dust & filler particles using Selleys Sugar Soap or Selleys Super Kleen. Safety tips Low hazard material For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$12.18
Key Features Fill cracks and holes in a single application Pre-mixed and ready to use Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints
$19.14
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint! Features Fills cracks and holes in a single application Pre-mixed and ready to use Goes on pink and dries off-white when ready to sand Minimal shrinkage so no need to overfill Very fast drying allowing sanding and painting in a short time period Comes complete with a filling spatula for ease of use Water based, so can be cleaned up with water Paintable with oil and water based paints Where can this product be used? Filling cracks and holes on surfaces where no structural movement occurs Filling cracks in walls, ceilings, doors, windows Repairing holes in walls, ceilings, doors and windows What materials is this product suitable for? Plaster Wallboard Wood Plasterboard Masonry Fibrous cement Primed nail heads Size 180g Tub Colours Pink, dries off white Technology Water Based Use Interior Exterior Ensure surfaces are clean, dry and free of loose material. Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill. Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times. Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting. Limitations: Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water. Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall. Nailing this product is not recommended. Avoid using below 5°C or in wet conditions.
$18.00
Selleys Paint Over Sealant is a permanently paintable sealant. Features Paintable Smooth flawless finish. Easy to use and can be used on damp surfaces. Superior adhesion to most building materials. Low odour so can be used in any environment without discomfort. Weather resistant by forming a durable seal which remains flexible, not drying or cracking Superior flexibility +/- 25% movement capability & up to 800% elongation or stretch. Temperature resistance – approximately -40°C +93°C Has a 25 year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. May be discoloured by contact with alloys containing brass, copper or zinc. Do not allow unused product to freeze. Where can this product be used? 10879.Window frames that need painting 102879.Capstones Masonry walls that need painting Perfect for use on or around: Bricks and concrete Windows frames Tiled and wooden fixtures Areas where a sealant is needed and where you want to paint it Not suitable for use in below waterline applications. Not suitable for use on oily woods such as cypress, teak or cedar. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Fibre Cement Painted Surfaces Ceramics Masonry Most metals Most plastics Wood How to use this product Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of sealant. Remove the tape before the sealant skins. For a better finish use a spatula dipped in detergent and water to tool off the sealant. Allow the surfaces to skin prior to painting, which is approximately 30 minutes. Protect from rain until firmly skinned. Allow for longer skin and cure times in damp conditions. Some water based under coats & flat paints may crack on drying. To reduce this effect allows the product to cure for 24 hours in small gaps or 48 hours in larger gaps before painting with such paints. To improve the paint finish, wipe the sealant with detergent solution immediately before painting. Avoid smearing sealant on the surrounding surfaces as this may effects its paintability. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irrtate sensitive skin. Avoid breathing in vapours. Ensure you use a well ventilated area as product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use keep the nozzle on the cartridge Silicone is a reactive product and is designed to cure once exposed to air. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$25.00
![Selleys No More Gaps Multipurpose Sealant Filler EZI Press [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125408_afb2d78a-8a52-46f4-b395-30543763e0ae.jpg?v=1754711827&width=645)
Selleys No More Gaps Multipurpose gap filler delivers a smooth finish and because of its superior flexibility and low shrinkage, those unsightly gaps and cracks won’t re-appear. Features Superior flexibility to cope with building movement, meaning the cracks and gaps will be hidden for longer. Has greater than 300% elongation/stretch and up to +/- 15% movement capability. Superior adhesion to a broad range of surfaces, resulting in a lasting finish. A smooth flawless finish and minimal shrinkage. Can be painted over with both water and oil based paints, after the surface has skinned (approximately 30 minutes* after application). Is formulated for long term resistance to cracking and crumbling. Easy water clean-up Will not stain building materials. Has good resistance to weathering. Low toxic, low odour, low VOC, less harmful to the environment Where can this product be used? Between window and door frames and the wall Along skirting boards Around cornices Between benchtops and tiles which are not exposed to water In corners or between walls and ceilings Between cabinets and cupboards Around air conditioning vents and the ceiling Where shrinkage or movement has caused rigid fillers to crack Gaps with the maximum width of 25mm and depth of 12mm What materials is this product suitable for? Timber Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Masonry Ceramic Tiles Glass Aluminium Paint Many other building materials
$17.85
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7ce782d52b264c1db0e928662698e299.jpg?v=1757753227&width=645)
$16.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/51345fd2ddf64a74a03e2c6b9e0d7e1a.jpg?v=1757753232&width=645)
$17.26
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/81e21d7d520d41a280976d39a403b5c9.jpg?v=1757753238&width=645)
$16.00
Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces. Where can this product be used? Boat repairs including hull repairs Surfboard / Surfski repairs Automotive repairs Repairing a leaky gutter Patching downpipes Patching metal roofs or grass catchers Not approved for contact with drinking water What materials is this product suitable for? Fibreglass Plywood Metal Fibro Sheeting Most Plastics How to use this product Wear rubber or plastic gloves when handling fibreglass Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge. For wide holes, glue a piece of cardboard to the back of the hole to form a base. Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly. Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels. Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required. Finishing When the patch has completely hardened, (approximately 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required. Clean up product with Solvent Acetone before it cures Handy tips At higher temperatures, the working time decreases. Can only be tinted with iron oxide or other dry pigments .which must be mixed in very thoroughly. Surfaces to be joined should be clean and dry. If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result. A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). In large amounts, heat can be generated during cure. Care should be taken on heat-sensitive surfaces with large amounts. Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Features Non-corrosive Weather resistant – resistant to water, weather or marine growth Rapid setting Impact resistant – can take knocks Sandable – can be sanded after 1-2 hours Can be painted over Extended working time – up to 20 minutes at 20°C Dries Opaque Heat resistant to 100°C
$41.01
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
![Selleys Armour Flex High Performance Adhesive [White]](http://gluesaustralia.com.au/cdn/shop/files/9300697125262_5e542168-6518-4fbd-97ab-586ab182d6e9.jpg?v=1754711932&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
![Selleys Armour Flex High Performance Adhesive [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125293_a1f282bb-e154-4d4c-812a-1cc8034e1e80.jpg?v=1754711935&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$23.14
![Selleys Armour Flex High Performance Adhesive [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125286_24a1028f-4655-4200-8859-8e45b8c9ab19.jpg?v=1754711936&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$24.23
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$16.93
Selleys 650FC: The Ultimate Adhesive Sealant Powered by Advanced Hybrid Technology Key Features +/- 20% Joint movement capability Excellent UV & Weather Resistance Superior Strength & Instant Grab Can be applied on damp surfaces Applications This product can be used in various applications such as trafficable joints, air conditioning ducting, caravan construction, perimeter seals around doors, windows, and general interior joint sealing. Compatibility Highly compatible with most building materials including timber, concrete, metals, and more. Not suitable for PVC, polyethylene, and temperatures above 80°C. How to Use Ensure surfaces are clean and dry. Apply using a sealant gun and spread evenly within 10 minutes. Storage and Cleanup Store in cool, dry conditions below 30°C. Uncured product can be removed with mineral turps. Precautions This product is not suitable for constantly submerged joints or temperatures beyond 80°C.
$20.00
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$15.92
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$16.52
![RiteTack Instant Grab Construction Adhesive 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/0799439671669_6c8563d0-64cb-499e-a564-d2d4a62e9ce2.png?v=1754712007&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/0793591712994_c9bef70a-42d0-408c-8b14-e176578d110d.png?v=1754712009&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/0793591712987_0ace0873-9628-42fc-9b06-c64c93c74c40.png?v=1754712010&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$19.17
A two-part gap filler and binder for builders and tradesmen that is a safe alternative to the toxic solvent and styrene-based fillers and bogs on the market. Environmentally friendly and non-hazardous for safe handling and easy transport Easy to mix, spread on rough and smooth substrates immediately Rapidly sets in 15 mins (faster in warm weather) with minimal shrinkage Curing time approximately 60 minutes • Long shelf life when firmly sealed after each use Once cured it may be chiselled, filed, sawn, planed and sanded into shape Can also be nailed, drilled, screwed, glued and painted Highly recommended for waterproofing as gap filler for bathroom renovations and other wet area applications where tiling or painting is required
$24.90
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$7.50
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications. Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried. Environmentally friendly Dries white Dries fast Very high weather resistance Unique properties make this product easy to shape and sand Ideal for schools and craft classes or just having fun!
$16.50
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application. Easy to mix and use White finish Non-shrinking Easily sanded Can be nailed or screwed when dry Water-resistant
$13.50
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$71.95
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$6.07
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$135.00
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$9.25
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates. Easy to use Can be tinted Ready-mixed Interior & exterior Environmentally friendly Heavy-duty bonded filler Ideal for floors, walls, ceilings, roofs
$17.04
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$25.00
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$9.00
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates. Features Benefits Water-based Ease of application Strong Easy spreading Flexible Time-saving Water-resistant Easy clean-up Pre-mixed Uses FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints. Surface Preparation All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards. Application: Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system. Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools. Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns. Requires: 2 coats. Method: Trowel or broad knife. Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours. Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C. The temperature should not fall below 10 °C during the drying process. Clean-up: Water. Safety: Dust Mask
$175.00
Specially developed for filling cracks & dents on doors, windows, trim, architraves and skirting boards, sanding to a smooth, hard mirror like finish. The perfect preparation for gloss paints. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Plasterboard, concrete, timber & primed metal (INTERIOR & EXTERIOR) Fill depth: Up to 3mm Dries in: 3 hours Ready to use: YES Available in: 330mL & 770mL Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Using the attached filling blade press filler in firmly and remove excess. * Allow to dry for 2-3 hours in thin 2-3mm applications, depending on humidity. Allow longer drying times if painting with oil based paint and for deeper applications. • Sand with fine sandpaper. For a perfect finish after initial sanding back, apply another very thin coat of filler, allow to dry and sand lightly with very fine (400grit) sandpaper before painting. • Protect from rain until painted over. • Not for exterior timber likely to absorb excessive amount of water. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Why should I use a specialised filler under gloss paints? A. Gloss paints show up every flaw and bump on surfaces. Therefore, a specialised filler that ensures an extremely smooth, hard, "glass-like" finish is preferred for the ultimate flawless, flat surface. Polyfilla Trim and Doors is the ideal filler under gloss paints. It also gives perfect gloss retention so you won't notice a 'dull' spot under the paint. You should also apply an undercoat before the final coat of paint for the best results.
$18.94
Ideal for filling holes, cracks, dents, chips and grain imperfections on interior timber surfaces. Can be nailed or planed. Easy to sand, sets to a hard finish and is highly crack resistant. Filling blade included For use on: Timber (INTERIOR) Fill depth: Up to 6mm Dries in: 2-3 hours Ready to use: YES Colour: Produces a pine finish that can be tinted or stained. Application Tips • Surface to be filled should be clean and dry with no loose or powdery material. • Using the attached filling blade press filler in firmly and remove excess. * Allow drying for 2-3 hours in 2-3mm thin applications, depending on humidity. Allow longer drying if painting with solvent-based coatings (24 hours minimum) or for deeper applications. • Sand with fine sandpaper. For a perfect finish after initial sanding back, apply a thin coat of filler, allow to dry and sand lightly with very fine (400 grit) sandpaper before staining or coating. • When tinting or staining, the final colour is not achieved until the varnish is applied. • Prime metals (eg, nail heads) before applying filler. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. I want a filler that matches the colour of the timber I am repairing. What should I use? A. The best idea is to custom tint/stain a filler to match your timber, rather than buy a pre-tinted colour filler. This allows you the flexibility to adjust to the shade you require, rather than having the colour dictated by the manufacturer. For interior timbers, use Polyfilla Timber Filler. If you require a wood filler that can be exposed to the elements, use Polyfilla Exterior Timber, which flexes with the natural movement of wood. Note: When tinting /staining, the final colour is not achieved until a varnish is applied. It is worth testing first on an off-cut or inconspicuous area to see if the correct colour match is achieved.
$22.74
Polyfilla Skim Coat 510g: The Ultimate Smooth Surface Maker for a Flawless Paint Job Seamless Filler for Pro-Level Paint Preparations When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 510g. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application. Key Features: Extremely easy to sand Sets to a super hard finish Highly crack resistant Ready to use, dries in just 2 hours For use exclusively on interior plasterboard & gyprock How to Use: Make sure the surface is clean, dry, and free from loose material. Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly. Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting. For optimal results, apply a paint undercoat before using water or oil-based paint top coat. Limitations & Tips: Use Poly Gap filler or silicone sealant for areas with joint movement. Clean up immediately with water before the filler dries. For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution. Polyfilla Skim Coat 510g is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
$20.22
Polyfilla Skim Coat 1.2kg: The Ultimate Smooth Surface Maker for a Flawless Paint Job Seamless Filler for Pro-Level Paint Preparations When it comes to ensuring the best possible surface for your painting projects, look no further than Polyfilla Skim Coat 1.2kg. This product excels in filling small cracks, dents, and fine imperfections, setting the stage for a smooth paint application. Key Features: Extremely easy to sand Sets to a super hard finish Highly crack resistant Ready to use, dries in just 2 hours For use exclusively on interior plasterboard & gyprock How to Use: Make sure the surface is clean, dry, and free from loose material. Press the filler firmly into cracks and holes. For larger areas, use a trowel to spread evenly. Let it dry for 2-3 hours depending on the humidity. Sand it for a smooth finish before painting. For optimal results, apply a paint undercoat before using water or oil-based paint top coat. Limitations & Tips: Use Poly Gap filler or silicone sealant for areas with joint movement. Clean up immediately with water before the filler dries. For hairline cracks, consider using Poly Small Cracks filler for a comprehensive solution. Polyfilla Skim Coat 1.2kg is your definitive choice for a crack-free, smooth surface, ready to be painted. It's your gateway to perfection!
$35.69
Polyfilla Rapid 30 100g: Your Go-To Quick-Set Filler for Interior and Exterior Surfaces Quick, Reliable, and Versatile Filler for All Surface Types If speed is of the essence, Polyfilla Rapid 30 100g is your ultimate choice for a high-quality plasterboard filler. Fill cracks, gaps, dents, and holes effortlessly in both interior and exterior surfaces. Key Features: Extremely easy to sand Sets to a hard finish Highly crack-resistant Fills up to 50mm deep holes Dries in as fast as 30 minutes* Suitable for multiple surfaces: plasterboard, brick, timber, and concrete How to Use: Clean and dry the surface, ensuring no loose or powdery material. Press the filler firmly into dents and holes, feathering edges to minimize sanding. Allow 30-60 minutes drying time for thin applications, longer for oil-based paints and deeper applications. For the smoothest finish, top with Poly Small Cracks and apply a paint undercoat before the final top coat. Limitations & Tips: Use Poly Gap filler where joint movement occurs. Do not fill more than 50mm deep. Clean up with water before the filler dries. For quick paint-over solutions, consider using Poly Quick Dry. *Drying time is based on a 2mm application. With Polyfilla Rapid 30 100g, you are not just buying a filler; you are investing in speed, quality, and versatility for your home improvement projects.
$12.35
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$46.19
Polyfilla P10 Gap Filler Rapid: The Ultra-Fast Solution for Perfect Fills Features Flexible Smooth Finish Rapid Drying Paintable in 10 minutes* Low Shrinkage Crack-Resistant* Applications Ideal for filling gaps around cornices, wall joints, skirting boards, as well as inside windows and door frames. Usage Instructions *To avoid paint cracking, apply to gaps no larger than 5mm deep and 10mm wide at temperatures above 20°C. Allow the sealant to dry before painting. Avoid applying paint too thickly. When to Use Paintable in just 10 minutes, allowing for fast project completion.
$7.35
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$11.74
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$84.97
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$29.00
A ready to use filler excellent for filling small cracks, dents & fine imperfections to ensure the ultimate smooth surface prior to painting. Extremely easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Plasterboard & gyprock (INTERIOR) Fill depth: Up to 2mm Dries in: 2 hours Ready to use: YES Size: 770mL Colour: White • Surface to be filled should be clean and dry with no loose or powdery material • Using the attached filling blade press filler in firmly, remove excess and feather edges to minimise sanding. Apply with a trowel to spread over larger areas. • Allow to dry for 30-60 minutes for thin 2-3mm applications, depending on humidity. Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • Ideal as a topcoat over other fillers for a perfectly smooth finish. • For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries Q. What can I do about hairline cracks in my ceiling? It's impossible to cover them up with paint? A. Paint rarely conceals cracks and is more likely to make them more obvious.It is best to use a filler that is easy to apply and sand such as Polyfilla Interior Small Cracks. It's ideal for covering fine cracks over a broad area.
$29.00
You have seen 192 out of 261 products
Formulations designed to accept colour matching, great for trims, panels and visible joints. Confirm paint type (water/solvent) and recommended over-paint timing. Use filters to refine by chemistry and cure profile. Always review the product page and TDS/SDS.
