Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$52.31
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$27.90
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$160.00
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$13.90
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$29.00
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$26.67
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$15.50
![Monarch Mini Gap Filler [White]](http://gluesaustralia.com.au/cdn/shop/files/9320090029080_1b178ddb-e3de-4ec1-83bb-8e320595bdb3.jpg?v=1754712311&width=645)
$2.84
![Monarch Mini Gap Filler [Cream]](http://gluesaustralia.com.au/cdn/shop/files/9320090030581_c5a95353-e7ee-4d92-8445-93066291f976.jpg?v=1754712313&width=645)
$6.02
![Monarch Mini Gap Filler [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9320090030574_91b63521-91d4-427c-ba6f-c5f54343a9c6.jpg?v=1754712314&width=645)
$6.02
![Monarch Mini Gap Filler [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090030567_dd3b7bac-a9e5-4986-9275-2bff35fb52de.jpg?v=1754712316&width=645)
$6.02
Monarch Mini Fill Sand Go™ MONARCH MINI® FILL SAND GO™ is an all in one solution to almost every DIY filling repair job. It’s a quick-dry, ready mixed, water-based formula that is suitable for small to medium cracks and holes in plasterboard & timber surfaces. The innovative MONARCH MINI® FILL SAND GO™ is a 3 in 1 product solution that includes a filling blade applicator as well as an ingenious sanding tool with a reversible sanding sponge. This allows you to complete the filling repair from start to finish without the hassle of requiring extra tools. FEATURES Innovative 3 in 1 Solution Filler, Applicator & Sanding Puck with Sponge All included Suitable for Interior repairs on Plasterboard & Timber BENEFITS Quick Dry Formula Ready to Use Multi-Purpose Filler Paintable Sandable Low Shrinkage UV Resistant Low Odour
$14.04
Monarch Mini Easy Nails Beige: The Compact, Quick-Grip Construction Adhesive Features & Benefits Fast grab for immediate adhesion High bond strength secures various building materials No sag, minimal vertical slip Easy water clean-up Suitable for timber, metal, ceramics, and masonry Why Choose Monarch Mini Easy Nails Beige? When it comes to small construction projects, Monarch Mini Easy Nails in Beige offers the perfect solution. Its compact design allows for easy application in tight spaces, especially when used with a Monarch Mini Compact Caulking Gun. Not only does it provide a strong bond, but it also allows for quick water clean-up, making it an essential choice for any DIY or professional project.
$4.48
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended on Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fiberglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Properties High impact resistance Won’t crack when drilled Moulds into different shapes Will fit into any shape of crack Does not shrink One-time application Sandable and paintable Blends with surroundings Cures under water Great for emergency in-water repairs Step 1: Safety Precautions Wear gloves. Step 2: Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Step 3: Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Step 4: Cleanup Cured putty may be cut away with caution using a sharp blade.
$18.00
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended For Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fibreglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Not Recommended For Potable water systems. Applications above 121°C (250°F). Polyethylene and polypropylene. Structural applications. Safety Precautions Wear gloves. Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Cleanup Cured putty may be cut away with caution using a sharp blade.
$35.00
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_1ec2ac38-d5ee-448a-869a-ebd682688cb3.jpg?v=1754715959&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_e15aa915-f631-45bf-a31f-e1c90de968b7.jpg?v=1754715959&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$19.86
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_7b1ca3d2-d36e-4090-b9b6-2eae8421c80d.jpg?v=1754715955&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [Black]](http://gluesaustralia.com.au/cdn/shop/files/5010305059165_048877d1-353e-447d-a42c-df19d2e12c4a.jpg?v=1754715955&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$19.86
Loctite® Epoxy Weld Bonding Compound is a two-part system consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to quickly produce a tough, rigid, high strength bond. Loctite® Epoxy Weld can be used as a convenient alternative to welding. It can be used as an adhesive for repairing, filling and rebuilding all metal and common surfaces. It cures to a metallic gray finish and can be easily sanded, drilled, machined or painted when fully cured. Loctite® Epoxy Weld does not shrink and is resistant to most shop fluids such as water, diesel fuel, gasoline, antifreeze, hydraulic fluid, motor oil and transmission fluids. Won t crack when drilled or machined Can be used outdoors One-time application Quick completion of project Can withstand temperatures up to 350°F (177°C) intermittently Good for applications requiring shear strength up to 3000 psi High impact resistance Water resistant Does not shrink Sets in 4 to 6 minutes High heat resistance Exceptional bond strength Recommended on Repairing machinery, appliances, tools, lawnmowers, automotive components, pipes, and embedding bolts and screws into metal Bonding various types of metal such as iron, steel, aluminum, brass, bronze, copper and pewter Properties High impact resistance Won’t crack when drilled or machined Water resistant Can be used outdoors Does not shrink One-time application Sets in 4 to 6 minutes Quick completion of project High heat resistance Can withstand temperatures up to 350°F (177°C) intermittently Exceptional bond strength Good for applications requiring shear strength up to 3000 psi HOW TO USE: Step 1: Safety Precautions Avoid skin contact. Keep away from eyes. Avoid prolonged breathing of vapors. Apply in a well ventilated area. Open windows and doors to achieve good cross-ventilation. Wear safety glasses to protect eyes, and rubber or plastic gloves to protect skin. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Pierce tube nozzles using the reverse side of the caps. Squeeze out equal amounts of resin and hardener on a clean, disposable surface. Prepare only as much as can be used within 3 minutes of mixing. Recap tubes immediately after use. Match the black cap with the resin and the white cap with the hardener. Mix resin and hardener together for approximately 1 minute or until it is uniform in color. Step 3: Application Apply to surfaces to be filled or bonded. Join and press parts together. When bonding butt joints, adhesive should be applied as a reinforcing fillet or splint over the joint for additional support. Remove any excess glue immediately with acetone, mineral spirits or rubbing alcohol. Support until bond sets in 10 to 15 minutes at room temperature. Parts can be handled within 15 minutes and machined within 16 to 24 hours. Cure time is lengthened in cooler temperatures and shortened in warmer weather. Step 4: Cleanup Clean excess glue immediately with acetone before adhesive sets. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$15.17
Loctite Marine Epoxy can be applied and cured underwater and eliminates the need to drain out water before repairs. This unique epoxy is a resilient, two-part adhesive system consisting of an epoxy resin and a hardener. When mixed in equal volumes with the convenient dual-syringe applicator, the resin and hardener react to produce a tough, rigid, high strength bond that sets 2 hours and fully cures in 24 hours. Ideal for repairing PVC, copper, brass and galvanized pipes, Loctite Marine Epoxy bonds to metal, concrete, glass, fiberglass, ceramic, wood and certain rigid plastics and cures to a white finish that can be easily sanded or machined. This resilient epoxy does not shrink and is resistant to water, most common solvents, and high impact.
$30.76
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink One-time application Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$9.23
SteelStik is a hand-mixable, steel-reinforced, non-rusting epoxy putty that quickly repairs or rebuilds anything made of metal. After mixing, it forms an industrial-strength polymer compound that can be moulded into shapes or used to build up patch and repair steel components. SteelStik sets in 3-5 minutes and after 60 minutes, can be drilled, tapped, machined, ground, filed and painted. SteelStik cures to a dark grey colour is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF. GREAT FOR Automotive & Machine Parts Exhaust Systems Plumbing Stripped Threads Rust Damage Household Repairs STRENGTH 900 PSI SET TIME 5 Minutes CURE TIME 1 Hour CURE COLOR Dark Grey USE ON Automotive Brick Ceramic Concrete Epoxy Putty Sticks Metal Under Water/Wet And More
$12.95
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More Strenght: 3960 PSI Set Time: 4-6 Hours Cure Time: 15-24 Hours Cure Colour: Dark Grey Use on: Automotive Brick Concrete Epoxy & Adhesives J-B Weld Metal Pro Sizes And More
$32.00
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be moulded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white colour, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first. GREAT FOR Rigid & Semi-flexible Plastic ABS, PVC & CPVC Pipes Automotive Trim & Bumpers Fibreglass Parts Vinyl Siding STRENGTH: 350 PSI SET TIME: 25 Minutes CURE TIME: 3 Hours CURE COLOR: Off White Drinking Water Safe USE ON Automotive Ceramic Epoxy Putty Sticks Fiberglass Plastic/Composite/PVC And More
$21.00
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Fibreglass Plastic/Composite/PVC Wood And More PREPARE Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair. MIX After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly. APPLY Apply with appropriate tool in an even coat, weld bead or extruded shape as needed. DRY Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
$18.00
Plastic Bonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. Plastic Bonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, Plastic Bonder sets to a tan colour and cures to a hard, permanent bond. GREAT FOR Filling Dents Bumpers Automotive Trim Composite Panels Interior & Exterior Plastic Parts Fibreglass USE ON Automotive Brick Ceramic Concrete Epoxy & Adhesives Fibreglass Plastic/Composite/PVC Wood And More
$19.95
KwikWeld™ is a fast-setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. KwikWeld™ has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. KwikWeld™ cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF. GREAT FOR Household Repairs Automotive Plumbing Marine Crafts & More USE ON Automotive Brick Ceramic Concrete And More
$16.00
HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF GREAT FOR Exhaust Manifolds Tail Pipes Mufflers Engine Blocks Duct Work Machinery High Temperature Projects USE ON Automotive Metal And More
$25.00
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey color. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured. Great For: Household Repairs Automotive Plumbing Marine Crafts & More STRENGTH: 3960 PSI SET TIME: 4-6 Hours CURE TIME: 15-24 Hours CURE COLOR: Dark Grey Use On: Automotive Brick Concrete Epoxy & Adhesives Fiberglass J-B Weld Metal And More
$15.50
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
$12.50
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.90
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
$14.47
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.10
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
FiberFix Rigid Patch is the other cousin of the Repair Wrap- a fibreglass patch for permanent repairs on flat or hard-to-wrap surfaces. Simply apply the patch over the hole and expose to sunlight or UV light (but don't expose before applying!). In 3-5 minutes after exposure, the patch will cure! What's Included?: One 3"x3" patch, One 2"x8" patch, One 5"x5" patch Cure Time: 5-10 minutes (depending on the amount of sunlight/UV exposure) What Surfaces Will It Work On?: Any rigid surface (will not work on flexible surfaces such as fabrics or highly bendable plastic) Sandable/Paintable?: Yes! Applications: Rain gutters, fences, garbage barrels, water tanks, boats, canoes, automotive body, and much more!
$34.50
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$42.00
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$35.00
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$31.00
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/9310492265001_6fb5fccc-7784-41bb-9997-bbd917e3c834.png?v=1754712704&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$22.51
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Bostik Nail It Fast Cure White: The Acrylic Adhesive for Rapid, Strong & Odorless Bonds Product Overview Bostik Nail It Fast Cure is a fast-curing, versatile acrylic adhesive that offers strong and durable bonds. It's easy to apply and almost odorless. Key Benefits Solvent-free formula Suitable for EPS and XPS Non-corrosive towards metal Easy to apply and clean Applications Specifically developed for bonding: Wood, chipboard, hardboard uPVC to brickwork, stone or concrete Ceramic tiles to porous substrates Limitations Not suitable for PE, PP, PC, PMMA, PTFE, soft plastics, neoprene, and bituminous substrates. Not designed for continuous exposure to water or for movement joints. Application Instructions Apply the adhesive in a ventilating manner, using vertical stripes or dots. Material should be placed by shoving and pushing firmly. Surface Preparation All substrates must be solid, clean, dry, and free from grease and dust. For porous substrates, priming may be required. Cleaning & Maintenance Tools and uncured material can be cleaned with water or Methylated Spirit. Cured material must be removed mechanically. Bostik HANDY WIPES are recommended for cleaning hands. Colour Options Available in white.
$6.96
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$15.00
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$25.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$19.36
You have seen 240 out of 246 products
Formulations designed to accept colour matching, great for trims, panels and visible joints. Confirm paint type (water/solvent) and recommended over-paint timing. Use filters to refine by chemistry and cure profile. Always review the product page and TDS/SDS.
