Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$21.72
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects. Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color Full Cure: 24 Hours Application For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet. Clamping The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied. Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood. Cure Time (amount of time for glue to reach total bonding strength): 24 hours Clean Up Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse. Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse. Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water. To remove Gorilla Wood Glue from hands, wash with warm soap and water.
$12.00
Meet your go to epoxy putty for fast, permanent style repairs. Gorilla All Purpose Epoxy Stick is a hand mixable putty that sets in about 10 minutes and cures in 24 hours to a tough, machinable finish. Once cured it can be drilled, sanded, and painted. It is waterproof, non rusting, and ready for indoor or outdoor jobs around the home, car, boat, and garden. Why you will like it Fast setting. Approximate set time 10 minutes. Paintable after about 1 hour. Full cure in about 24 hours for a hard wearing repair. Works on most common materials including metal, PVC, many rigid plastics, wood, stone, ceramic, brick, concrete, fiberglass, and glass. Non rusting formulation for durable repairs in wet or humid areas. Waterproof when cured. Suitable for indoor and outdoor use. NSF ANSI 61 certified drinking water safe for contact with potable water once cured. Great for Plumbing repairs such as sealing low pressure leaks and patching drainage pipes Automotive trims and general panels that do not exceed service temperature of typical epoxy repairs Household fixes like filling holes, anchoring hardware, rebuilding small parts, and edge repairs DIY and craft projects that need a sculptable, sandable fill Important use notes Not for exhaust systems. For plumbing, use for temporary repair of drainage pipes or low pressure pipes only. Turn water off, apply, then wait at least 1 hour before turning water back on. Bonded wood should not be submerged or soaked after repair. How to use Wear disposable gloves. Work in a well ventilated area. Prepare the surface. Clean off dust, oil, and loose material. Roughen smooth surfaces with sandpaper. Cut the amount you need. Remove the film wrapper and foil sticker. Reseal unused putty to limit air exposure. Knead for 30 to 60 seconds until the colour is uniform. Mix thoroughly or it will not harden completely. Apply within 5 minutes of mixing. Press firmly into place. Smooth with wet gloved fingers if a smooth finish is desired. Remove any squeeze out before hardening. Allow to set about 10 minutes. Paint after about 1 hour. Full cure about 24 hours. Specifications Format Hand mixable epoxy putty stick Size 56.7 g Set time About 10 minutes Paintable After about 1 hour Full cure About 24 hours Indoor or outdoor Yes, waterproof when cured Drill, sand, paint after cure Yes Drinking water contact NSF ANSI 61 certified drinking water safe once cured Clean up and storage While uncured, wipe away with soap and water, acetone, or isopropyl alcohol. For cured material, remove by sanding, scraping, or chiseling. Store the stick in its vial with film and foil sticker re applied. Keep sealed in a cool, dry place. Keep away from children and animals. Safety Wear gloves during mixing and application. Avoid contact with skin and eyes. If in eyes rinse with water for 15 minutes. If on skin wash with soap and water. Use in a well ventilated area. For medical emergencies in Australia call 000.
$17.90
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$28.10
FiberFix Rigid Patch is the other cousin of the Repair Wrap- a fibreglass patch for permanent repairs on flat or hard-to-wrap surfaces. Simply apply the patch over the hole and expose to sunlight or UV light (but don't expose before applying!). In 3-5 minutes after exposure, the patch will cure! What's Included?: One 3"x3" patch, One 2"x8" patch, One 5"x5" patch Cure Time: 5-10 minutes (depending on the amount of sunlight/UV exposure) What Surfaces Will It Work On?: Any rigid surface (will not work on flexible surfaces such as fabrics or highly bendable plastic) Sandable/Paintable?: Yes! Applications: Rain gutters, fences, garbage barrels, water tanks, boats, canoes, automotive body, and much more!
$34.50
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$42.00
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$35.00
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$31.00
![Bostik Seal N Flex Auto & Marine FC Adhesive & Sealant [Black]](http://gluesaustralia.com.au/cdn/shop/files/9310492265025_0316718a-8147-4bdd-955a-19d6d8a0bc59.png?v=1754712705&width=645)
Noise, vibration, and impact dampening properties are exceptional. Adhesion and sealing qualities are excellent. Tack-free time and cure speed are both quick. It's safe to use in both salt and fresh water. Designed in Australia Seal N Flex Auto & Marine FC is a high-performance, fast-curing polyurethane adhesive and sealant from Bostik. Bostik Seal N Flex Auto & Marine FC has remarkable adhesion properties and is appropriate for a wide range of internal and external industrial and automotive adhesion applications. It's paintable, slump-resistant, and water-resistant, as well as resistant to fungal assault.
$23.45
Bostik Nail It Instant Grab White: Grab It Fast, Hold It Forever Product Overview Bostik Nail It Instant Grab White is a high-quality professional adhesive crafted with MSP (Modified-Silyl Polymer) technology. It offers extremely high initial tack, eliminating the need for fixation or support during curing. Smart Advantages Extremely high initial tack No fixation or support needed during curing Free of isocyanates, phthalates, solvents, and silicones Suitable for both interior and exterior use Non-corrosive towards metals Almost odorless Resistant to moisture, weather, and UV Applications Universal bonding adhesive suitable for: Stone, Concrete, Glass Metals, Alloys, Stainless steel Plastics, Polyurethane, PVC Wood, Paint Systems Directions for Use Application should be done in vertical stripes using a caulking gun. No need for fixation or support due to high initial strength. Limitations Not suitable for certain plastics, continuous water exposure, or movement joints. Cleaning & Safety Remove excess uncured adhesive with Bostik Handy Wipe or a damp cloth. Cured adhesive can only be mechanically removed. Product Codes & Specifications Available in 290ml cartridges. Temperature resistance ranges from -40°C to +90°C.
$18.00
Bostik Nail It Fast Cure White: The Acrylic Adhesive for Rapid, Strong & Odorless Bonds Product Overview Bostik Nail It Fast Cure is a fast-curing, versatile acrylic adhesive that offers strong and durable bonds. It's easy to apply and almost odorless. Key Benefits Solvent-free formula Suitable for EPS and XPS Non-corrosive towards metal Easy to apply and clean Applications Specifically developed for bonding: Wood, chipboard, hardboard uPVC to brickwork, stone or concrete Ceramic tiles to porous substrates Limitations Not suitable for PE, PP, PC, PMMA, PTFE, soft plastics, neoprene, and bituminous substrates. Not designed for continuous exposure to water or for movement joints. Application Instructions Apply the adhesive in a ventilating manner, using vertical stripes or dots. Material should be placed by shoving and pushing firmly. Surface Preparation All substrates must be solid, clean, dry, and free from grease and dust. For porous substrates, priming may be required. Cleaning & Maintenance Tools and uncured material can be cleaned with water or Methylated Spirit. Cured material must be removed mechanically. Bostik HANDY WIPES are recommended for cleaning hands. Colour Options Available in white.
$6.96
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$15.00
QuikSteel reinforced epoxy putty, 2 ounce Withstands up to 500 degree Fahrenheit temperatures Sets in 5 minutes, cures in 1 hour Hardens like steel, can be drilled, tapped, filed, sanded and painted Drinking water safe, NSF-61
$25.00
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$15.00
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Specifications Application Dent Fill Brand Bondo® Color White, Off white Product Type Glaze Putty Substrate Aluminum, eCoat or Paint, Galvanized, SMC Details Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Fast curing makes putty sandable in only 20 minutes Putty is compatible with all types of automotive paint systems Use during the Fill stage of the 3M™ Body Repair System Bondo® Professional Glazing & Spot Putty smooths and repairs pin holes, scratches, nicks, minor dents, stone chips and other surface imperfections in automotive paint and bodies. This product is a 2-part component formula that securely and quickly bonds to primer, metal, fiberglass and aluminum. Professional Quality Surface Blemish Repairs Bondo® Professional Glazing & Spot Putty quickly repairs paint scratches, minor dents and stone chips. Our professional quality formula comes as a two-part product with putty and cream hardener to produce a mixture that won't shrink once cured. This glazing and spot putty has a 5-minute working time and a 20-minute curing time, giving you the perfect balance of enough time to complete the repair with a fast cure that keeps your project moving forward on schedule. Perfect Repairs Every Time Once cured, you're ready to sand to create a smooth patch that matches the surrounding surface beautifully. Our repair putty securely bonds to primer, metal, fiberglass and aluminum, and it resists gumming up sandpaper and shrinking. It can be used with all types of paint systems for professional-looking results. Use During the Fill Stage of the 3M™ Body Repair System Even a small repair can seem complex at first. So 3M's Body Repair System simplifies the entire automotive body repair process by dividing it into four stages: Stage 1 — Prepare. This stage includes pulling dents, removal of paint and rust and efficient, effective masking of the area. Stage 2 — Fill. This stage involves patching holes with reinforced filler and smoothing and shaping filler before painting. Stage 3 — Paint. This stage includes painting the area and blending and smoothing primer and paint. Stage 4 — Finish. The final stage for showroom-grade results: removing small defects, sealing and polishing clear coats and other painted surfaces. 3M supplies premium products such as abrasives, tapes, body fillers and tools for every stage. This system helps you work easily, efficiently and successfully across the entire body repair process.
$75.00
You have seen 257 out of 257 products
Formulations designed to accept colour matching, great for trims, panels and visible joints. Confirm paint type (water/solvent) and recommended over-paint timing. Use filters to refine by chemistry and cure profile. Always review the product page and TDS/SDS.
