Note: If you are working on a timber floor, you will need to use Fix-A-Floor Polyurethane for Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive, now patented, is an extra-strength bonding adhesive designed specifically for re-bonding loose and hollow tiles, marble and stone without the cost and mess of removing or replacing them. Fix-A-Floor is a simple DIY repair solution that is fast, easy and affordable, and surprisingly rewarding. If you can operate a drill, a caulking gun and mix a small batch of grout, you can do it. It works on all types of subfloor materials. Just Drill & Fill! Tip: For more precise application or smaller holes, you can include the 30 mL Adhesive Syringe with Blunt Tip Fill Needle when purchasing this product. It makes applying the adhesive cleaner and more accurate, especially in tight or narrow grout lines. The Nozzle The nozzle of the 300 mL Fix-A-Floor tube is specially engineered with a pre-drilled 3 mm hole to make it ideal for filling drilled holes in loose or hollow tile, marble and stone floors. It is firm enough to form a strong seal for optimal flow and complete coverage. Markings on the nozzle indicate cut points for 4.5 mm, 6 mm or any size you need, making it suitable for both narrow grout lines and wider applications. The Adhesive Fix-A-Floor Repair Adhesive is strong and flexible, featuring elastomeric bonding properties that prevent future issues caused by foundation movement, expansion and contraction of the subfloor or poor original installation. Used by flooring professionals for years, this product allows any homeowner to fix loose, hollow or squeaky tiles quickly and permanently. It is non-toxic, non-flammable and eco-friendly. Whether you are repairing a small area or a large floor section, Fix-A-Floor delivers lasting results and is guaranteed for the life of your floor. Just Drill & Fill! FAQs Q: Will Fix-A-Floor work with heated floors?A: Yes. Many customers use Fix-A-Floor over heated floor elements with no issues. Turn off the heating before, during and for 48 hours after applying. Q: Some of my grout is missing. Can I still use Fix-A-Floor?A: Yes. If small gaps or cracks exist, simply Drill & Fill. The adhesive will re-bond and stabilise loose areas. If the grout is completely missing, re-grout lightly, allow it to dry and then apply Fix-A-Floor. Q: Can I repair my whole floor or just one tile?A: Fix-A-Floor works on all sizes of problem areas, from a single tile to an entire room. It is suitable for all types of tile, marble and stone floors. Q: Can I use Fix-A-Floor outside?A: Yes. It performs well in both interior and exterior applications, including patios and decks. Q: Can I use Fix-A-Floor in showers or pools?A: No. It is not recommended for areas exposed to constant or excessive moisture. Q: Is Fix-A-Floor safe?A: Yes. It is a non-toxic, non-flammable, water-based adhesive that is safe and environmentally friendly. Q: Can I use it to re-glue a tile that has come loose?A: Yes. Apply Fix-A-Floor directly to the floor where the tile was, press the tile firmly into place, apply weight and allow to cure for 24 hours. Q: Do I need to place weight on the floor after filling?A: It is recommended to place some weight, such as a heavy object or bucket, on the area to aid curing and ensure even distribution. It is not mandatory but helps achieve optimal results. Q: What if adhesive does not appear from other holes?A: The adhesive may still be spreading beneath the tile. Move to the next hole and continue filling. Make sure you are not pressing the nozzle down onto the subfloor during application.
$34.95
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
Say Goodbye to Stubborn, Sticky Messes! Tired of wrestling with stubborn price tags that tear and leave a papery, sticky mess? Frustrated by gummy residue left behind by tape on new appliances or furniture? We've all been there, risking our fingernails and damaging surfaces trying to scrape and scrub away unwanted adhesives. It’s time to stop the struggle. Introducing Un-Du® Adhesive Remover, the ultimate solution from Glues Australia that works like magic. This isn't just another solvent; it's a revolutionary removal system. Unlike harsh chemicals that dissolve glue and ruin your items, the Un-Du® formula cleverly works by temporarily neutralizing the adhesive. A few drops are all it takes to seep under the label or sticker, breaking the bond with the surface. Simply lift it off cleanly and effortlessly with the handy included scraper tool. The best part? Once the fast-evaporating Un-Du® formula disappears, the stickiness on the sticker returns, allowing you to reuse it somewhere else! It’s the perfect tool for repositioning labels, photos, and more. An Essential Tool for Every Australian Home From the kitchen to the garage, you'll find hundreds of uses for Un-Du®. It’s the one tool that’s more versatile than duct tape, designed to solve all those sticky problems that pop up in daily life. Keep a bottle handy and you'll always be prepared. Gift Giving Made Easy: Effortlessly removes price stickers from delicate gifts like crystal vases, books, and photo frames without leaving a trace. Clean Up Your Car: Finally get rid of that old bumper sticker from your ute or the remnants of a parking permit on your windscreen without damaging the paint or glass. Appliance & Furniture Rescue: Safely removes warranty stickers, energy rating labels, and masking tape from new fridges, TVs, and fine wood furniture. Household Accidents: Lifts chewing gum from carpet, tar from floors, and crayon marks from walls with remarkable ease. The Ultimate Office & Warehouse Productivity Hack Streamline your workflow and maintain a clean, professional workspace. Un-Du® is an indispensable asset for any office, mailroom, or warehouse environment, saving you time, money, and frustration. Package & Mail Management: Open self-sealing envelopes and padded mailers without tearing them, perfect for retrieving contents or reusing packaging. File & Asset Organisation: Easily remove and replace labels on files, shelves, computer disks, and office equipment without leaving a sticky, dirt-collecting residue. Mistake Correction: Quickly lifts correction fluid (White Out) from documents without smudging or tearing the paper. Workspace Maintenance: Removes old tape marks from desks, partitions, and windows, keeping your office looking pristine. A Must-Have for Crafters and Memory Keepers Your precious memories and delicate projects deserve the best care. The Un-Du® formula is completely acid-free and photo-safe, making it the trusted choice for hobbyists, scrapbookers, and archivists who demand perfection and preservation. Scrapbooking Perfection: Safely lift and reposition photos in albums and scrapbooks without causing fading, yellowing, or damage. Model Making: Remove masking tape from delicate models without lifting paint or leaving residue. Paper Crafts: Adjust stickers and embellishments on acid-free and lignin-free papers with total confidence. Stop struggling and start un-sticking the clean, simple, and safe way. Add Un-Du® Adhesive & Sticker Remover to your cart today and discover a world free from sticky situations! Product Specifications Brand: Un-Du® Product Name: Adhesive & Sticker Remover Formula: Acid-Free, Photo-Safe, Quick-Evaporating Solvent Key Feature: Temporarily neutralizes adhesives, allowing for the reuse of most stickers and labels after evaporation. Residue: Leaves no oily, greasy, or sticky residue behind. Tool: Comes with an attached, non-scratching, integrated scraper tool for easy lifting. Common Applications: Sticker & Label Removal Tape & Decal Removal Price Tag Removal Gum & Tar Cleaning Correction Fluid (White Out) Lifting Opening Sealed Envelopes Safe For Use On Surfaces Including: Glass & Plastics Fine Wood Furniture Metals Carpets & Upholstery Delicate Fabrics Photos Acid & Lignin-Free Papers Painted Surfaces & Wallpaper And much more!
$20.37
Araldite Two-Part Epoxy Adhesive delivers maximum strength bonding for a wide range of materials. The mixed product gels in 2 hours, achieves initial bonding within 6–8 hours, and reaches full strength after 3 days. Features Chemical reaction of the two parts provides superior strength Bonds a wide variety of surfaces Dries clear for a clean finish Extremely strong and durable Highly water resistant – suitable for fixing tiles around pools (not below the waterline) Forms a rigid, long-lasting bond Fills small gaps – surfaces do not need to fit perfectly Excellent chemical and heat resistance Clamping recommended for a stronger bond Not suitable for Polypropylene or Polyethylene plastics Bond strength weakens above 80°C but recovers when cooled Appearance Translucent Where to Use Load-bearing repairs Fixing loose table or chair legs Reattaching hammer heads Bonding aluminium sheets Timber repairs on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets or skis Securing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastic (except Polyethylene and Polypropylene) Crystal Leather Directions for Use Ensure all surfaces are clean, dry, and free of grease, rust, and paint. For best results, roughen smooth surfaces after cleaning. Dispense equal parts of Part A and Part B onto a clean, disposable surface (e.g. polyethylene or cardboard). Mix thoroughly using a spatula, nail, or stick. Apply immediately to both surfaces and press together. Clamp for 6–8 hours while the bond sets. Remove excess adhesive and clean tools immediately. Replace the correct caps on each tube to prevent hardening. Handy Tips Mix in small quantities for maximum working time – larger mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover. Do not swap caps between tubes – lids and tubes are colour coded. Uncured Araldite can be wiped off with acetone or nail polish remover. Once cured, remove mechanically by scraping or sanding – solvents will not dissolve it. To reposition a cured bond, heat gradually to 150°C (if the item is heat resistant), reposition, and allow to cool. For surface prep: use Selleys Liquid Sugar Soap on porous materials, or Methylated Spirits on non-porous surfaces. Use Selleys Kwik Strip Smart to remove tough residues if needed. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapours. Do not use solvents near eyes or open wounds. In case of eye contact, rinse with water for at least 15 minutes and seek medical advice. Non-toxic once fully cured. Refer to the Material Safety Data Sheet for more details. Storage & Reuse Ensure caps are replaced tightly after use and store in a cool, dry place.
$76.88
The unique rubber-infused gel formula allows powerful bonds that are extremely precise even on flexible materials. Ideal for porous and vertical surfaces, and strong enough to withstand extreme conditions. The gel’s high strength non-drip formula then dries transparent to form invisible bonds that give a long lasting durability that is both weather and shock-resistant. For intricate, hard to reach spots, Loctite Power Flex Gel Control features an easy grip squeeze bottle and nozzle for precise applications. Recommended on: Rubber, Leather, Wood, Metal, Porcelain, Paper, Plastic. Properties: -Rubber infused gel formula for extra strong and flexible bonds -Ideal for porous and vertical surfaces -Water resistant -Bonds in seconds -Withstands heavy loads -Dries transparent -Easy to open, self-piercing and anti-clog cap -Choice of applicators: convenient tube or easy grip control with a longer nozzle -Suitable for use on most surfaces* -Solvent-free -* Except polyethylene (PE), polypropylene (PP), car glass, Styropor® and synthetic fibres. Step by Step Ensure surfaces to be joined are clean, completely dry and close fitting. Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$12.50 $10.95
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$19.32
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_1ec2ac38-d5ee-448a-869a-ebd682688cb3.jpg?v=1754715959&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_e15aa915-f631-45bf-a31f-e1c90de968b7.jpg?v=1754715959&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$23.52
Gorilla Spray Adhesive is heavy duty, multi-purpose and easy to use. Gorilla Spray Adhesive forms a clear, permanent bond that is moisture resistant and can be used on projects both indoors and out. This spray adhesive is also photo safe. Its wide pad nozzle and controlled, fine mist spray provide an even application on the project you are working on. PRODUCT FEATURES HEAVY DUTY: Dries Permanent EASY TO USE: Repositionable CLEAR COLOR: Non-Yellowing* INDOOR & OUTDOOR: Moisture Resistant CONTROLLED SPRAY: Even Application WIDE PAD NOZZLE PHOTO SAFE All surfaces should be clean and free of dirt, grease and oil. Protect surrounding areas from overspray to avoid residual adhesive. Shake can well before using. Hold the can 15 to 20cm from surfaces to be bonded and spray an even coat of adhesive. For Maximum Bond Strength: Spray both surface to be joined. Allow to dry to tack (approximately 1 minute) and press surfaces firmly together. For Repositionable Bonds: Spray a light even coat on one surface. Allow to dry 1-3 minutes before joining. Repositionable up to 10 minutes depending on surface type, then bond becomes permanent. To remove, gently peel from corner. Tip: To avoid possible clogging, turn can away from body, turn upside down and spray a short jet of clear gas after completing the job. *Not recommended for use on vinyl materials, automotive headliners, polypropylene, polyethylene or similar materials. Do not use for bonding weighted materials. APPLICATION TEMPERATURE – 10°C to 32.2°C OUTDOOR – Yes MOISTURE RESISTANT – Yes PAINTABLE –Yes SANDABLE – Yes STAINABLE – No CURED COLOR – Clear PHOTO SAFE – Yes How do I remove Gorilla Spray Adhesive from my surface? To clean surface while adhesive is still wet/uncured, wipe adhesive off the project with a dry cloth. Isopropyl alcohol (IPA) may be used according to manufacturer’s instructions. Once cured, Gorilla Spray Adhesive may be removed using mechanical means by gently scraping surface, being careful not to damage the surface underneath. How do I remove Gorilla Spray Adhesive from body/skin? While still wet, Gorilla Spray Adhesive can be removed by wiping adhesive with a dry cloth, and then washing the area with soap and water. Once cured, rinse well with water. Is Gorilla Spray Adhesive food safe? Gorilla Spray Adhesive is not recommended for direct or indirect food contact and should not be considered food safe. What surfaces will Gorilla Spray Adhesive bond to? Gorilla Spray Adhesive is a multi-purpose product that will bond a wide variety of surfaces including fabric, paper, wood, plastic*, cardboard, foam, metal and more! NOTE: Not recommended for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content. Not for use on food contact surfaces. Will Gorilla Spray Adhesive bond vinyl/acrylic/rubber? Gorilla Spray Adhesive will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP) or polyethylene (PE) plastics, vinyl, or any type of rubber with high oil or plasticizer content.
$26.00
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6–8 hours, with maximum bond strength after 3 days. Features Stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries clear Very strong and durable bonding High water resistance (suitable for tiles around pools, but not below the water line for that use Selleys Knead It Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat resistant Clamping recommended for stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but is regained when temperature drops Appearance Translucent Where Can This Product Be Used? Load-bearing repairs Gluing the head back on a hammer Fixing loose table or chair legs Bonding aluminium sheeting Bonding timber on boats Repairing splits and cracks in cricket bats Bonding fibreglass sheets Repairing skis Fixing Dynabolts and metal rods into concrete Suitable Materials Glass Metal Wood Fabric Rigid plastics (except Polyethylene and Polypropylene) Crystal Leather How to Use Ensure all surfaces are clean, dry, and free from grease, rust, or paint. For best results, roughen smooth surfaces after solvent cleaning. Dispense equal volumes of Part A and Part B onto a clean disposable surface (e.g. cardboard or polyethylene) and mix thoroughly. Apply adhesive immediately to both surfaces and press together. Clamp the bond for 6–8 hours while setting. Scrape off excess adhesive and clean utensils immediately. Handy Tips Mix in small quantities for longer working time — large mixes cure faster. Replace caps immediately after use and wipe nozzles with acetone or nail polish remover before sealing. Ensure caps are placed on the correct tubes (they are colour-coded). Remove uncured adhesive with acetone or nail polish remover. Once cured, remove by mechanical scraping or sanding — solvents will not dissolve the product. To reposition a cured bond, heat slowly to at least 150°C (if safe for the material), then scrape off excess and reposition carefully. For cleaning surfaces before use: Porous surfaces use Selleys Liquid Sugar Soap Non-porous surfaces (e.g. glass, metal) — clean with methylated spirits For stubborn residue use Selleys Kwik Strip Smart Ensure the surface is dry before applying. Safety Tips Avoid contact with skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of eye contact, flush with water for 15 minutes and seek medical attention. Non-toxic when set. Refer to the Material Safety Data Sheet (MSDS) for more information. Storage & Reuse Replace caps tightly after use. Store in a cool, dry place.
$24.50
Loctite Super Glue Professional in a bottle has proven superior performance over ordinary super glues. It works faster and holds stronger on more surfaces than ordinary instant adhesives thanks to a patented additive. Loctite Super Glue Professional's super strength formula is ideal for heavy-duty projects and repairs. It dries clear and sets without clamping. Loctite Super Glue Professional is resistant to moisture, most chemicals and freezing temperatures. Recommended For:-Repairing figurines, costume jewellery, cameras, toys, metal car parts, wiper blades, rubber seals and O-rings-Bonding leather, cork, paper, cardboard, wood, chipboard, fabric, metal, ceramic, rubber and hard plastics such as Plexiglass, polycarbonate, polystyrene and PVC Not Recommended For:-Styrofoam, foam rubber, pure bone china, glass, silicone rubber, PTFE, polyethylene and polypropylene-Use in dishwasher, oven or microwave-Use on repairs needing high flexibility-Glazed surfaces Safety Precautions:Well-ventilated area, gloves. Preparation:Surfaces must be clean, dry and free from oil, wax and paint. Protect work area. Lightly roughen smooth surfaces for better adhesion. Pre-fit parts to be joined. Application:Twist off the cap by turning counter-clockwise. Apply sparingly to one side only using approximately one drop per square inch of surface. Press surfaces together immediately. Hold in place for 15 to 30 seconds until bond sets. Do not reposition parts. Clean excess adhesive with tissue paper and replace the cap. Cleanup:Cured adhesive may be cut away with caution using a sharp blade, removed with Duro Super Glue Remover, acetone or with boiling water.
$23.00
![Sikasil Pool Neutral-Cure Silicone Sealant 300 ml [White]](http://gluesaustralia.com.au/cdn/shop/files/Sikasil_pool_white.webp?v=1760227901&width=645)
Sikasil® Pool Neutral-Cure Silicone Sealant – 300 ml Cartridge Designed for use in demanding aquatic environments, Sikasil® Pool is a one-part, neutral-curing silicone sealant formulated specifically for swimming pools, wet areas, and permanently submerged joints. With exceptional resistance to chlorinated water, high elasticity, and outstanding fungal resistance, this sealant delivers durable, long-lasting performance. Key Features Excellent resistance to chlorinated water and common pool chemicals Movement accommodation of ± 25 % Neutral cure — non-corrosive, safe on most metals and tile systems High elasticity and recovery Very good resistance to fungal attack Suitable for interior and exterior applications Typical Applications Underwater joints in swimming pools Wet areas, such as spas, splash zones, and shower recesses Sealing between tiles, concrete, glass, and metal substrates Technical Highlights Service temperature range: –40 °C to +80 °C Shore A hardness (28 days): ~20 Elastic recovery: > 90% Typical curing speed: ~2 mm per 24 h Skinning time: ~5 minutes (23 °C / 50% RH) Available in White, Grey, and Transparent shades Shelf life: 15 months (when stored unopened between 5 °C and 25 °C) Usage & Application Tips Ensure surfaces are clean, dry, and free from contaminants (oil, dust, grease). Roughen smooth, non-porous surfaces (e.g. metal, glazed tile) before application. Use appropriate primers (e.g. Sika Aktivator-205, Primer-3 N) on metals, PVC, or porous substrates as recommended. Apply a closed-cell foam backing rod to control joint depth. Insert sealant by cartridge gun, avoiding air entrapment. Tool the bead within the skin formation time. Allow full cure (minimum 7 days) before filling pool with water. Limitations & Precautions This product is not suitable for: Joints in direct contact with potable food or drink Overpainting Use on substrates that leach oils, plasticisers or solvents (e.g. bitumen, EPDM rubber) Always consult the current Product Data Sheet (PDS) and Safety Data Sheet (SDS) for full technical, safety, and application details before use.
$27.38 $0.09/ml
Sikaflex®-111 Stick & Seal is a high-performance 1-part multipurpose adhesive and sealant that bonds and seals a wide range of construction materials for both internal and external applications. Its advanced silane-terminated polymer technology delivers exceptional adhesion without surface pre-treatment, even on damp substrates. Key Features Bonds well to a wide variety of substrates without surface pre-treatment Adheres to damp concrete and other porous materials Compatible with most construction materials, including EPS/XPS and building wraps Excellent mechanical strength and weathering resistance Low VOC, LEED v4 EQc 2 compliant, and EC 1PLUS certified Ideal for bonding and sealing in indoor and outdoor environments Where to Use Designed for professional and DIY use across construction and renovation projects. Perfect for bonding or sealing: Concrete and masonry Wood and timber components Ceramic, stone, and tiles Metal surfaces Glass and plastic materials such as PVC, PA, PET, and EPS/XPS Applications Adhesive for bonding construction components Sealant for vertical and horizontal joints Repairs, renovations, and installations in building and civil works Technical Information Composition Silane-terminated polymer Density ~1.40 kg/L (ISO 1183-1) Shore A Hardness ~36 (after 28 days) Tensile Strength ~1.5 N/mm² (ISO 37) Elastic Recovery ~75 % (ISO 7389) Service Temperature −50 °C to +80 °C Curing Rate ~3 mm per 24 h (at 23 °C / 50 % r.h.) Skinning Time ~35 minutes (at 23 °C / 50 % r.h.) Colour Options Available in White, Concrete Grey, and Black. Packaging 290 ml cartridge | 12 cartridges per box Storage & Shelf Life Store unopened in a cool, dry place between +5 °C and +25 °C. Shelf life 12 months from production date. Certifications CE Marking – EN 15651-1 (Facade elements Class F EXT-INT CC 20HM) GEV-EMICODE EC 1PLUS (Very Low Emissions) LEED v4 EQc 2 Low-Emitting Materials compliant French VOC Regulation Class A+ Why Choose Sikaflex®-111 Stick & Seal This versatile adhesive-sealant provides superior adhesion on most construction materials, making it the go-to solution for professionals and renovators who need reliable bonding and sealing performance. Whether you are working on concrete, metal, or plastic, Sikaflex®-111 Stick & Seal ensures a flexible, durable, and weather-resistant joint every time.
$23.98
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 3g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$4.00
Easy to use, fast setting adhesive system to repair ALL plastics. Features -Bonds ALL Plastics, including Polyethylene (PE) and Polypropylene (PP) -Easy to Apply -Dries clear for clean, neat results -Fast Bond: 2-30 seconds -No clamping necessary -No mixing required -self-piercing, clog-free cap on adhesive -Also bonds plastic to other surfaces: Metal, timber, china, rubber, leather Where can this product be used? -For interior projects and repairs -For fast & easy repair of household items made from plastic -Repair Toys & Games -Fix Car accessories -Repair Kitchen plastics and utensils -Repair Office items -Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet -Best results for Nylon items (e.g. car parts) are achieved without initial priming. Contact Selleys consumer advice if unsure of plastic type. -Not suitable for use on glass – we recommend Selleys Araldite Ultra Clear. What materials is this product suitable for? -ALL Plastics -Adhering Plastic to Metals China Rubber Leather How to use this product -Ensure the surfaces to be joined are close fitting, clean, dry and free of dust. -Using the primer pen, liberally coat plastic surface/s that are to be bonded. -Pierce seal at end of the adhesive tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a very small amount of glue to one surface only. Bring surfaces together and apply slight pressure. -The adhesive will grab within 2-30 seconds, depending on environmental conditions and materials being bonded. -Allow at least 30 minutes for sufficient bond strength for practical use. -Wipe tip of the tube, replace the cap and store upright in a dry cool place. Handy tips -If using on leather test on an inconspicuous area first as adhesive may cause leather to discolour or harden. -Not suitable to repair items that will contain hot liquids. -Best results for nylon items are achieved without Initial priming (e.g car parts). Contact Selleys Consumer Advice if unsure of plastic type. -Will also bond plastic to non-plastic surfaces (Metals, Timber, China, Rubber, Leather). Do not use primer on non-plastic surfaces. -After use, wipe excess product from the adhesive nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in the hot soapy water. -Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safety tips -Keep Out of reach of Children -Avoid contact with skin and eyes and avoid breathing in the vapour. -Bonds on contact. Should fingers stick together apply a solvent such as acetone (nail polish remover) to contact areas then wash with water. -Do not use solvents near eyes or open wounds. -Highly Flammable, keep away from sources of ignition. -Contents of the pen may cause lung damage if swallowed. -This product is hazardous according to the criteria of NOHSC and HSNO. For frequent hobby or occupational use, please refer to the Material Safety Data Sheet. -For Advice, contact a Poisons Information Centre (phone Aust. 131 126, NZ 0800 764 766) or a doctor. -In case of eye contact immediately flush with water for at least 15 minutes and seek medical attention. Storage and re-use -Ensure caps are replaced and store in a cool dry place.
$8.51
PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. - Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.
$16.17
A rapid dual-action adhesive system is specially designed to work on plastic to form resilient, invisible bonds in seconds. Recommended on: Plastic, Porcelain, Metal, Rubber, Leather, Wood, Paper. Properties: Bonds even difficult to bond plastics such as polyethylene (PE) and polypropylene (PP) Bonds in seconds Dries transparent Easy to open, self-piercing and anti-clog cap Suitable for use on most surfaces* Solvent-free * Except Styropor®, car glass and synthetic fibres. Use: Ensure surfaces to be joined are clean, completely dry and close fitting. Using the Surface Activator like a pen apply it to both surfaces and wait 60 seconds to dry. Twist the glue cap clockwise until it locks, then unscrew in an anti-clockwise direction to open. Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set. Replace the cap immediately and store upright in a cool dry place.
$10.67
Clear Boyle Craft Glue Boyle Craft Glue (Clear) is a versatile, water-based adhesive designed for everyday making and detailed craft work. It dries clear and odourless, making it perfect for neat, mess-free results on paper projects, school assignments, scrapbooking, model making, décor builds and more. Why You’ll Love It Dries crystal clear for a clean, professional finish. Water-based & odourless for a low-fuss, indoor craft experience. Heat & light resistant—ideal for display pieces exposed to room lighting/sunlit interiors. Easy-squeeze bottle gives smooth, controlled bead lines and spot application. Cleans up with water—simply wipe while wet for quick tidy-ups. Suitable Materials Formulated for strong, reliable bonds on: Paper, cardboard & posters Wood, balsa & craft sticks Plastics* Glass & ceramics Metal embellishments Fabrics & felt Yarns, beads & sequins Leather and more *Always test first—some low-energy plastics may require light surface prep. Great For School projects & classroom crafts Cardmaking, scrapbooks & photo boards DIY décor, event styling & mood boards Miniatures, models & hobby builds Textile embellishment on felt and fabric (non-washwear items) How to Use Prep: Ensure surfaces are clean, dry and free of dust or oils. Lightly roughen very smooth surfaces for best grab. Apply: Squeeze a thin, even layer to one surface. For porous materials (paper, cardboard, wood), a little goes a long way. Assemble: Press parts together. Use light pressure, clips or tape if needed to hold while setting. Dry: Allow to dry thoroughly. Dry time varies with bead thickness, temperature and humidity. Clean-up: Wipe excess immediately with a damp cloth. Wash tools in water while glue is still wet. Good to Know Indoor use: Formulated for indoor crafting and display. Clear finish: Dries transparent to help hide glue lines and squeeze-out. Heat & light resistance: Helps projects maintain appearance under typical indoor conditions. Washes out with water: Clean hands, tools and fresh spills while wet. Specifications Base Water-based Appearance (dry) Clear Odour Odourless Cleanup Water (while wet) Use Indoor Tips & Testing For non-porous surfaces (glass, metal, some plastics), apply a thin coat to each surface, wait briefly, then join for better grab. Always perform a small test on off-cuts or an inconspicuous area to confirm compatibility and finish. Avoid heavy, load-bearing or structural applications—this is a craft-grade adhesive. FAQs Does it dry clear?Yes—Boyle Craft Glue dries clear for a neat finish. Can I wash it out?Yes—while wet, it washes out with water. Once fully dry/cured, removal may be more difficult. Is it suitable outdoors?It’s designed for indoor craft projects. For outdoor or constantly wet environments, choose a weather-rated adhesive.
$14.89
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts. -Bonds a variety of surfaces -Dries Crystal Clear so there’s no visible evidence of repair -Quick setting in 5 minutes -No clamping necessary -High water resistance -Forms a rigid, durable bond -Can be used for gap filling (Surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Doesn’t yellow over time so is ideal for use on glassware Appearance: Crystal Clear Where can this product be used? -Fixing a broken glass vase -Repairing jewellery -Toy repairs -Fixing ornaments or crockery -Fixing your handbag strap -Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic -Crystal -Leather How to use this product: -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. -When using tube kit, ensure correct caps are replaced on each tube or they will adhere. Handy tips: -A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). -Clamping is recommended for a stronger bond. -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set. Storage and re-use: Ensure caps or lids are replaced and product stored in a cool dry place.
$21.85
Dunlop Ready-to-Go Coloured Grout is a premium, pre-mixed grout for fast, clean results on walls and floors. No mixing, no mess, just open, apply, and buff for a smooth, long-lasting finish. The formula includes Grout Shield for anti-mould and anti-bacterial protection to help surfaces stay cleaner for longer. Suitable for interior and exterior applications, and available in a wide colour range to match or contrast your tiles. Ready-mixed convenience, apply straight from the tub Contains Grout Shield for mould and bacteria resistance Use on walls & floors, indoors & outdoors* Ideal for joint widths from 1–5 mm Great for rejuvenating old grout (min. removal depth: 1 mm walls, 2 mm floors) *Always follow the data sheet guidance for your specific area and exposure. Where to Use Ceramic, porcelain and most glazed tiles Bathrooms, kitchens, splashbacks, laundries, living areas Light-duty exterior tiled areas (check exposure & substrate) This grout is designed for typical domestic and light commercial tiling where a smooth, uniform finish is desired. Colours & Finish Available in a contemporary colour palette (e.g. whites and greys) to complement most tile styles. Use Dunlop’s colour selector to visualise combinations before you start. Coverage Coverage varies by tile size, joint width and depth. As a guide (per kg) of grout: Tile size (L×W×Thickness) Joint width 1.5 mm Joint width 3 mm Joint width 5 mm 25×25×4 mm mosaics ≈1.04 m²/kg ≈0.52 m²/kg ≈0.31 m²/kg 100×100×8 mm ≈2.08 m²/kg ≈1.04 m²/kg ≈0.63 m²/kg 200×200×8 mm ≈4.17 m²/kg ≈2.08 m²/kg ≈1.25 m²/kg Tip: Allow an extra 10–15% for wastage due to technique, tile type and site conditions. Directions (Summary) Prep: Ensure joints are clean, dry, and free from dust, adhesive residue and contaminants. For rejuvenation, remove at least 1 mm (walls) or 2 mm (floors) of old grout. Apply: Using a rubber grout float, force grout firmly into joints at a 45° angle. Strike & shape: Allow grout to firm in the joint (~15 mins). Shape joints as required. Clean: Wipe diagonally with a dense, damp sponge, rinsing frequently. Use minimal water to reduce shade variation and shrinkage. Buff: When touch-dry (typically 6–24 hrs), buff tile faces with a clean, dry cloth. Drying & Use Initial set at ~24 hrs at 23 °C / 50% RH Shower walls can be exposed to water after ~24 hrs Clean-Up & Storage Clean tools and residue with water while the grout is still wet. Reseal the tub between uses to prevent skinning. Store upright in a cool, dry place. Safety Read the Safety Data Sheet before use and follow PPE guidance. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children.
$16.30 $0.02/g
Tarzan’s Grip new formulation is a clear, flexible, general purpose solvent-based adhesive for household and hobby uses. An all-purpose glue which bonds almost everything Grabs in minutes - the exact "grab time" depends on the surfaces to be joined Fast drying Water resistant
$5.13
One-component, solvent-free, multipurpose adhesive and sealant with a crystal clear appearance suitable for most surfaces 100% crystal clear / transparent Good workability Very good adhesion on many typical building materials Use: Sikaflex® Crystal Clear is designed as a multipurpose adhesive and is suitable for most surfaces including: Plasterboard Wood surfaces Painted enamel Polyester Plastic Sikaflex® Crystal Clear is designed as a sealant for vertical and horizontal indoor connection joints between partition walls, for metal and wood constructions. CHARACTERISTICS AND ADVANTAGES 100% crystal clear / transparent Good workability Low shrinkage during cure Flexible and elastic Can be used on damp concrete Very good adhesion on many typical building materials COLOUR: Transparent Product Data Appearance / Colours Transparent Packaging 300 g cartridge (290 ml), 12 cartridges per box Storage Conditions / Shelf-Life Sikaflex® Crystal Clear has a shelf life of 12 months from the date of production, if it is stored properly in undamaged, original, sealed packaging, and if the storage conditions are met. Technical Data Chemical Base Silane terminated polymer Density 1.05 kg/l approx. (ISO 1183-1) Tensile Strength 2.0 N/mm2 approx. (ISO 37) Shore A Hardness 30 approx. (after 28 days) (ISO 868) Elongation at Break 400% approx. (ISO 37) Elastic Recovery 70% approx. (ISO 7389) Tear Propagation Resistance 4.0 N/mm approx. (ISO 34) Service Temperature −40 °C to +70 °C SUBSTRATE PREPARATION The substrate must be clean, dry, sound and homogeneous, free from oils, grease, dust and loose or friable particles. Sikaflex® Crystal Clear adheres without primers and/or activators. However, for optimum adhesion and critical, high performance applications, such as on multi-story buildings, highly stressed joints, extreme weather exposure or water immersion, the following priming and/or pretreatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, PVC, galvanised steel, powder coated metals or glazed tiles have to be cleaned and pre-treated using Sika® Aktivator-205, wiped on with a clean towel. Before sealing, allow a flash-off time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, also have to be cleaned and pre-treated using Sika® Aktivator-205,wiped on with a clean towel. After the necessary flash-off time, use a brush to apply Sika® Primer-3 N and allow a further flash-off time of > 30minutes (< 8 hours) before sealing the joints. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks shall be primed using Sika® Primer-3 N applied with a brush. Before sealing, allow a flash-off time of > 30 minutes (< 8 hours).For more detailed advice and instructions please contact the local Sika Technical Services Department. Note: Primers are adhesion promoters. They are neither a substitute for the correct cleaning of a surface, nor do they improve the strength of the surface significantly. Bonding After substrate preparation, apply Sikaflex® Crystal Clear in beads, strips or spots to the bonding surface in intervals of a few centimetres each. Use hand pressure only to set the element to be bonded into position. If necessary, use SikaTack® Panel Tape during the initial hours of curing. An incorrectly positioned element can easily be unfastened and repositioned during the first few minutes after application. Apply pressure again. Optimum bonding will be obtained after the complete curing of Sikaflex® Crystal Clear. The recommended adhesive layer thickness (depending on surface evenness) is ≤3 mm. Fresh, uncured adhesive remaining on the surface must be removed immediately. Final strength will be obtained after complete curing of Sikaflex® Crystal Clear. Sealing After the necessary substrate preparation, insert a suitable backing rod to the required depth and apply any primer if necessary. Insert a cartridge into the sealant gun and extrude Sikaflex® Crystal Clear into the joint making sure that it comes into full contact with the sides of the joint and avoids any air entrapment. Sikaflex® Crystal Clear sealant must be firmly tooled against the joint sides to ensure adequate adhesion. It is recommended to use masking tape where exact joint lines or neat lines are required. Remove the tape within the skin time. Do not use tooling products containing solvents. Cleaning of Tools Clean all tools and application equipment immediately after use with Sika® Remover-208 and/or Sika® Wonder Wipes. Once cured, residual material can only be removed mechanically.
$23.63
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$25.45
![Sika Sikasil Pool Silicone Water Resistance [Transparent]](http://gluesaustralia.com.au/cdn/shop/files/76128946_314287d6-23cc-4ab5-90d4-1c020429de31.png?v=1754711691&width=645)
$20.82
Selleys White For Life Tile & Grout Cleaner is a professional-grade cleaning solution specially formulated to maintain the appearance and hygiene of tile and grout surfaces. Its anti-bacterial formula effectively cuts through soap scum, dirt, and grime, restoring brightness without using harsh chemicals, bleach, or abrasives. Surface Preparation: Ensure the grout is fully cured before use. Conduct a spot test in an inconspicuous area to confirm surface compatibility. Application Instructions: Twist the nozzle to spray position. Spray directly onto the surface. Allow 1–2 minutes for light grime, or 3–5 minutes for stubborn build-up. Wipe using a damp sponge or cloth. Rinse thoroughly with clean water. For a streak-free finish on glass and taps, dry with paper towel before the surface dries. Coverage: Varies based on surface texture and soil level. A 750mL bottle covers approximately a standard-sized bathroom. Drying Time: Fast-drying; ensure complete rinsing and wiping for optimal results. Clean Up: Rinse tools and surfaces immediately after use. Wipe dry to avoid streaks on sensitive materials like brass, copper, or painted surfaces. Technical Data: Form: Liquid Colour: Pale Yellow Scent: Fresh Lime Use: Interior (kitchens, bathrooms, showers) Packaging: 750mL trigger spray bottle
$19.00
Selleys Wet Area Matt White: The Lasting Choice for Wet Areas Key Features Matt finish for elegant look 100% silicone sealant 25-year guarantee against cracking or peeling Waterproof seal with superior adhesion Mould-resistant formula Non-corrosive, neutral cure Best For Bathrooms, Kitchens, Laundries, Showers, Spas, Sinks, and Plumbing Fixtures. Suitable Materials Ceramic, Glazed & Porcelain Fixtures Metal, Copper & Brass Fittings Plastic Laminates Rubber Glass Stainless Steel Concrete & Grouts Many Plastics including Polystyrene How to Use Apply in a well-ventilated area. Clean surface, cut cartridge, fit nozzle, and apply with a caulking gun. Tool with a spatula dipped in detergent water within 5-10 mins of application. Limitations Not paintable Not suitable for certain materials and uses Handy Tips Mask sides for neater joints. Work in manageable sections for a smoother finish. Clean Up Uncured product may be removed with mineral turps. Cured product can be removed with Selleys Silicone Remover or by cutting and scraping. Additional Info Comes in a 420g cartridge, color is White, technology is Neutral Cure Silicone. Designed for interior use.
$18.00
![Selleys No Mould Silicone Selant 100ml [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/6fd66b047782417180c9a9563f0917d8.png?v=1757753033&width=645)
Selleys No Mould Silicone sealant is specially designed to create a long lasting waterproof seal in areas where mould resistance is necessary Features Superior formulation+ that stops mould growth* Fast skinning formulation which means you can use your shower in 1 hour Provides a durable waterproof seal Resists lifting Where can this product be used? Suitable for use in humid and damp environments such as Kitchens Bathrooms Laundries Showers Basins tiles Worktops Baths & spas Plumbing fixtures What materials is this product suitable for? Ceramic Glazed & porcelain fixtures Aluminium Plastic laminates Some rubbers Glass Stainless Steel How to Use Before applying your new sealant we recommend spraying Selleys Rapid Mould Killer into the gap to kill any residual mould Thoroughly clean surface where sealant will be applied with turps and dry completely Cut nozzle at 45°angle, cut cartridge tip and fit nozzle Place in a caulking gun, apply with steady pressure, ensuring sealant is pushed into the joint Tool with a spatula dipped in detergent water within 5-10 minutes of application Clean up with turps before product skins Limitations: +Compared to Selleys Wet Area #Sealant will be waterproof and shower ready in 1 hour after application in showers. The semi-cured sealant must not be touched until fully cured (at least 48 hours) *To maintain your sealant properties, ensure you regularly clean off any soap scum and dirt as these encourage mould growth Not suitable for aquariums, food or drinking water contact, permanent immersion in water, or metals other than aluminium and stainless steel. Not suitable for PE, PP, PTFE and some rubbers. Pre-test on other surfaces for compatibility Tips For neater joints, mask sides before applying the sealant and remove the tape before sealant skins Not paintable. Complete painting 7 days before applying the sealant
$14.32
SELLEYS LIQUID NAILS Original is a premium grade multi-purpose construction adhesive that delivers a consistently strong and lasting bond on most building materials. Shrinkage and thermal movement in buildings can cause bonds to weaken over time, but Liquid Nails is flexible enough to respond to movement allowing a strong bond to be maintained over time. Features Strong bond – which will cope with shrinkage and thermal movement, so you know the job will last. Adheres well to wet and dry timber, so there is no need to wait for the timber to dry. Easily extruded and easy to use in low Winter temperatures, so it allows you to continue with the job at low temperatures. Paintable when dry, to give you a neat, quality finished job. Doesn’t drip, sag or string, so there is less mess when you are using the product. Is available in a range of sizes and delivery styles. Meets requirements specified by Australian Standard AS 2329-1999. Bridges gaps on rough and ill fitting construction material Has a life expectancy, when cured, of 20 years Not for use on polyethylene, polypropylene, Teflon, silicone or polystyrene. Perfect for use: Sheet flooring to joists Metal or aluminium door strips to floors or walls Timber or fibre cement sheeting to cement block or brick walls Masonite to timber Wallboard or panelling to wood or metal frames Cork tiles to timber, fibro or plaster Tempered hardboard to floorboards To eliminate the squeaks in tongue & groove boards Not suitable for use on Mirrors, use Liquid Nails Mirrors, Metal and Glass Not suitable for use on Styrene Foam, use Liquid Nails Fast Not suitable for metals heated by direct sunlight, as bonds weaken at high temperatures. eg metal roofing and siding. Not suitable for bonding materials in areas which will be constantly damp or wet. Not suitable for use in tightly clamped joints eg cabinet making or joinery use Selleys Aquadhere What materials is this product suitable for? Brick & Concrete Plasterboard, particleboard & fibre cement sheeting Ceramic tiles Aluminium Painted surfaces Timber Hardboards Render Many other building surfaces How to use this product Ensure the surfaces to be bonded are clean, dry and free from dust, grease, oil and loose powdery materials. If porous surfaces are greasy or dirty, we would recommend cleaning the surface with SELLEYS LIQUID SUGAR SOAP, and allow to dry. If the surface is non-porous eg glass or metal, firstly clean the surface with Mineral Turpetine and then again with Methylated Spirits, and allow to dry. If there is old difficult to remove residue such as old flaky paint, we recommend using paint stripper such as SELLEYS KWIK STRIP SMART, and allow to dry. On wet timber pooled water should be wiped off. Highly oily timber types may need to be wiped with solvent prior to application to remove surface oils. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/ Course grain, as the construction adhesive will adhere more readily to a scratched up surface. Cut the seal at the top of the cartridge. Cut the nozzle end to desired opening (approx. 5mm diameter). Fit to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of work which requires a caulking gun. Apply a bead of product along the length of the joist, stud or batten. On broad flat surfaces apply beads every 40cm. Fix the surfaces with sufficient nails, screws or clamping to hold load and achieve contact over the total bond area. The product is repositionable for up to 20 minutes after fitting. Allow the adhesive to set (at least 24 hours) before removing any temporary fasteners or clamping. For faster grab, apply to one surface only, press together and pull apart. Allow surfaces to dry 2-5 minutes before firmly joining. The time it takes to form a strong bond depends on the nature and conditions of the application. In most situations strong bonds can be achieved after 24 hours and will continue to strengthen over a 2-3 day period. The product will fully cure up to 7 days. When the product is still wet it can be removed with mineral turpetine, otherwise if the product is dry it can be removed by sanding or scraping, we recommend using a 50mm ROTA COTA Soft Grip Scraper. Clean any excess from your hands with SELLEYS Hand Kleen Wipes. To eliminate squeaks in tongue and groove flooring, apply a bead of Liquid nails into the groove or each board when installing. Handy tips When applying to one surface, ensure sufficient LIQUID NAILS Original is used so that some adhesive extrudes out when surfaces are brought together then wipe off excess if necessary. If glue is not visible, then insufficient contact may not have been made between the surfaces and a weak joint may result. LIQUID NAILS Original should always be used in conjunction with mechanical fasteners in structural, critical or high stress applications. LIQUID NAILS Original is sometimes called LIQUID NAILS (SOLVENT) to differentiate it from the other Liquid Nails products. LIQUID NAILS Original shrinks slightly on curing. Cured LIQUID NAILS Original residues can be removed by holding a rag soaked in Mineral Turps against the residue, then rubbing the residue once softened. Mineral Turps penetrates in this way at approximately 1 mm per hour. When Liquid Nails Original joints are directly exposed to the weather, it is recommended to seal around the edges with a silicone sealant to prevent water ponding inside the joint and thus weaken the joint. LIQUID NAILS Original is NOT recommended for use on mirrors or polystyrene. Use LIQUID NAILS MIRROR METAL GLASS for mirrors and LIQUID NAILS FAST for polystyrene. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job.
$6.03
A versatile, hand kneadable fast setting epoxy putty that is ideal for repairing, rebuilding, reshaping or restoring almost anything. It can be drilled, filed, machined, screwed, sawn, sanded and painted. Packaged in a handy roll so you can just cut off what you require and save the rest for another day, it hardens in 5-10 minutes, after mixing. Approved for contact with drinking water. Features Will not sag, run or drip Easy to use – no mess Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing Good adhesive strength Can be used to reshape, rebuild and repair a multitude of surfaces and applications Good gap filling properties Long-lasting, durable solution Heat resistant to 120°C continuously or 140°C intermittently Can be used underwater. (but dry surfaces for application are best and recommended) Rapid set time (<10 minutes) Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649 Excellent anchoring properties Where can this product be used? Repair and replacement – timber, metal, masonry, many plastics, ceramics Mending – toys, appliances, lawn mowers, sports equipment etc Sealing – leaks in gutters and downpipes Patching – chipped concrete, floors, bricks, blocks etc Attaching – fixtures, machine tags, signs etc Anchoring – bolts, screws, housings etc Moulding – to reform-reshape damaged timber, metal, masonry, plastics, ceramics Moulding to rebuild – wrought iron fencing Forming knobs and missing parts Balancing – table legs etc Fixing a damaged roof tile Repairing a water (drinking) tank Lost the head off your hammer? Make a new one with knead it Replace chip in golf club (woods) Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Pot life (working life) decreases above 20°C Set time increases at temperatures below 20°C Approval for Drinking Water Contact to AS/’NZ4020:2005 subject to a maximum surface area: volume ratio of 10,375mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm What materials is this product suitable for? Wood/Timber Concrete Anchoring bolts Metal Masonry Plastics Ceramics How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Use gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 2 minutes of mixing) and mould to shape if required. For a smooth appearance, remove excess and hand rub with water or a damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 5-10 minutes Knead-It Multi-Purpose will harden and begin to form a strong bond. After 60 minutes Knead-It Multi-Purpose may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water before product hardens. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. Use Knead-It Aqua for applications in wet/ submerged areas. Use Knead-It Steel for applications on metal or fuel contact For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup Safety tips Where possible wear protective gloves when using Knead-It Multi-Purpose. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. If redness or swelling of the skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt. Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on the skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal. Storage and re-use Replace silver disc to seal ends and keep in a cool dry place.
$26.95
Selleys Glass Silicone is an acetic acid curing 100% silicone, which has excellent adhesion to glass and has been specially formulated for glazing and aquarium construction. Features The acetic curing formulation results in superior adhesion on glass and glazing surfaces. Superior silicone formulation forms a durable seal and which does not shrink when drying. UV and weather resistant remaining flexible, not shrinking, crumbling, cracking or drying out. Temperature resistance – approximately -60°C +150°C Superior flexibility +/- 25% movement capability & up to 400% elongation or stretch. 25-year guarantee – when used as directed, i.e. for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking or drying. Colour Clear Appearance Smooth Where can this product be used? Windows Glass aquariums Perfect for use on or around: Windows Windows Frames Glass Aquariums Repairs gaskets in dryers, ovens, refrigerators and washing machines. Repairs rips in awnings. Will not adhere to concrete, cement products, zinc or copper containing metals, marble, limestone or lead. Can not be painted over. Not suitable for use on oily woods such as cypress, teak or cedar. Not suitable for use on roofs and gutters as it will cause corrosion. Use SELLEYS Roof and Gutter Silicone. Not for use on polyethylene, polypropylene or Teflon. Pre-test plastics before use. What materials is this product suitable for? Glass Aluminium Stainless Steel Many plastics including polystyrene Most woods Rubber/ canvas Glazed ceramics & porcelain How to use this product Thoroughly clean and dry surface from oil, dirt and grease with Mineral Turpentine firstly and then Methylated Spirits. Allow drying completely before applying silicone. If there is old silicone which needs to be removed, we recommend using SELLEYS SILICONE REMOVER, this ingenious product makes removing old silicone easy. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. We recommend SELLEYS LIGHT SPEED Caulking Gun, as its new innovative pressure release design reduces the mess which results from run on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun and extrude the silicone sealant forcing the sealant into the gap and move in a pushing motion, along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpetine or for a professional finish use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpetine. Excess sealant must be cleaned up before the sealant skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpetine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately in mineral turpetine. Avoid smearing on surrounding surfaces, see handy tip. Sealant will cure fully in 72 hours. As this point, any unwanted sealant can be removed by trimming with a sharp blade but avoid undercutting the seal. For aquariums, allow the product to fully cure for 7 days. Prior to usage, thoroughly wash out with water, drain and refill before introducing fish. Suitable for constructing and repairing small aquariums. The specialist design required for large tanks. Contact SELLEYS if unsure. Handy tips Tips for Using a Silicone Sealant on Glass Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. The depth of the sealant should be no more than 10mm in joints. To fill larger joints use a suitable backing rod (such as closed cell polyethylene foam or similar), leaving the gap depth no larger than half the width of the joint. When first applying product, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish complete painting prior to use of the sealant as it can not be painted over. For a better finish, use a spatula dipped in mineral turpetine or detergent and water to tool off the sealant. Work in sections that can be completed before sealant skins. Tooling off and tape removal must be completed before skinning occurs or a rough surface may result, so working in sections allows for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up any spills and for cleaning any material off the skin before it cures. They are an easy and effective way to keep clean on the job. Safety tips Uncured product may irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Avoid breathing in vapours. Ensure you use a well-ventilated area as product releases acetic acid while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Store in cool dry conditions, below 30°C The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and is designed to cure once exposed to humidity. While the product may be stored for a few months once opened, it does have a limited shelf life. Storage in an upright position in a cool dry place is recommended to maximise the storage life. If the sealant is going to be used again within a few days, leave the nozzle on and merely extrude approximately 2 cm of the product before storing the cartridge upright. This will cure to a plug which can easily be pulled out when required. For longer storage periods, leave the nozzle on and place a piece of plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When you want to re-use the product, simply take off the foil and plug from the old nozzle pull out the excess silicone from the nozzle with a corkscrew, then re-pierce any cure at the tip of the cartridge and re-use. If cure has taken place into the cartridge, the product is unlikely to be in a useable state and should be discarded.
$17.35
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
Fast setting supa glue in a convenient bottle that allows easy, controlled and precise application. Features Easy, controlled application Non-drip glue saver nozzle, reduces waste and mess. Long fine nozzle for precise application Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve initial bond Non-clog cap Forms a rigid bond Upright self-standing bottle Comfortable to hold Where can this product be used? Ideal for small repair jobs or when immediate results are required. Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics Wood How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Hold bottle in an upright position. Pierce seal by attaching nozzle and cap and turning clockwise. Remove cap and squeeze gently to apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. (30 seconds). The product grabs within 5-30 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Maximum bond strength reached after 12 hours. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Reseal cap in a clockwise direction. Tap bottle lightly on a flat surface to clear excess product from nozzle. To remove excess from substrates, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using thias method. Ensure cap is replaced and store in a cool dry place. Cyanoacrylate based adhesives polymerise in the presence of moisture. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$6.00
Single Shot, no mess just throw away Self piercing tube Bonds in 10 seconds Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics
$6.00
Marathon Scale and Rust Remover CONCENTRATED 2L Bottle Tough on calcium, rust and scale deposits. Ideal to use on tiles, porcelain, sinks, showers and baths
$7.00
PC-7® is the original tough job epoxy! This paste epoxy was originally formulated more than 60 years ago for the maximum in bonding power. Professionals to the do-it-yourselfers select PC-7® because of its exceptional adhesion to metals, ceramics, masonry and many plastics. PC-7® is designed for permanent repairs. Where other adhesives fail…PC-7® won’t! Choose PC-7® if you want to: seal a crack in a wall, attach a hanger to a ceramic plaque, seal a leak in an oil pan, repair a granite monument, fix a leak in PVC pipe connection, create a multimedia sculpture, and thousands of other repairs. When mixed, part A (gray) and the hardener part B (black) react to form a bond of tremendous strength. The PC-7® formulation is slow curing, but slow can be a good thing especially for large tasks. WORKING TIME: 60 MINUTES CURE TIME: 24 HOURS (48 HOURS FOR FULL CURE) PC-7® is thick. Thick is good if you need to work vertically or want to hold an object in place. How thick? Thicker than peanut butter but not as thick as bubble gum. Here are just a few specific uses (there are hundreds of other uses): Bond metal electrical boxes to concrete wall. Fill cracks in basement walls. Rebuild vintage Bakelite steering wheels. Seal holes in oil and transmission pans or fuel tank. Bond and repair stainless steel. Attach transition strips on concrete floor. Attach firing strips to concrete wall. Bond to and rebuild hard rubber bumper. How to prepare a surface for bonding with PC-7 Epoxy Paste Remove contaminants such as dust, dirt, oil and grime with solvents such as Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper or wire brush. Smooth, glossy and shiny surfaces should be scuffed using sandpaper to increase adhesion. How to clean-up after PC-7 Epoxy Paste application Use Denatured Alcohol, Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner to clean tools and mixing surface before PC-7® cures. Clean hands and skin with soap and water. Cured epoxy can be removed by applying Paint Remover or Paint Stripper to soften the epoxy surface. Scratch off the softened epoxy. Repeat as needed. How thick can I apply PC-7®? PC-7® can be applied in any thickness. It does not require drying or exposure to air. It will cure from the inside out. I made a repair with PC-7® but need to build the area up more. Can I apply more epoxy? PC-7® sticks to PC-7® Can I use PC-7® for a vertical repair? PC-7® can be applied vertically and overhead. Because of its high viscosity it will not drip or sag. How long does it take PC-7® to harden? Normally, at 70F, PC-7® will cure in 24 hours but full hardness can take up to 48 hours. Cooler conditions will extend the cure time. Working in a garage or outside in temperatures between 50F and 60F may double the length of time needed for full cure. Applying PC-7® to a cool surface such as an exterior facing wall will slow down the cure. Can I paint over PC-7® and if so how? PC-7® should be primed then painted. Use Zinser Bullseye® 1,2,3 Stain Sealing Primer or Kilz® Premium Stain Sealing Primer or INSL-X® Stix Bonding Primer. Priming/sealing is important to separate and protect the finish coat from the epoxy/amine surface. Can I use PC-7® on a finished surface? Smooth, glossy or shiny surfaces should be roughened or scuffed with sandpaper to provide maximum adhesion. Use 80 or 120 grit sandpaper. A roughened surface has much more surface area than a smooth surface. PC-7® is very thick. Can I smooth it out or thin it out? Use a solvent such as Denatured Alcohol, Acetone, Rubbing Alcohol or Lacquer thinner to smooth applied PC-7®. Be-cause PC-7® is very thick and gooey, it is necessary to apply alcohol or acetone to the tool or gloved fingertips in order to lubricate the surface and shape or feather the applied epoxy. Can I use more of one part of PC-7® in order to speed the curing? Adding additional hardener does not make PC-7® cure faster. It is best to mix PC-7® one part of A to one part of B. However, PC-7® is probably the only epoxy that does not require precisely a 1:1 mix ratio. Plus or minus 25% A or B does not affect the performance. Adding additional PC-7® (+50%) part B hardener (black) can improve the adhesion to difficult surfaces such as PVC pipe and fittings. Measure equal volumes of part A epoxy (gray) and part B hardener (black) then measure an additional half portion of hardener (black). This will make the mix ratio (1 : 1.5, A : B). Can I tint PC-7® to match a surrounding color? PC-7® can be tinted with iron oxide or carbon pigments. Powdered pigments are used to color stucco or concrete and can be found at art supply stores. Universal tints that are used to color paint are compatible with PC-7®. Too much tint may affect the performance of PC-7®. I want to do a repair outdoors and the epoxy seems really stiff? PC-7® becomes more viscous in cool temperatures. Set the containers in a warm place prior to mixing. Acetone has been used to reduce the viscosity of PC-7®. The addition of acetone will contribute to shrinking and slow down the cure rate. PC-7® performs best without the addition of solvents. What will PC-7® bond to? It is easier to say what PC-7® will NOT bond to: Wax paper, Teflon, Plexiglass, vinyl and some softer plastics. Test an area if in doubt and always rough up shiny, smooth surfaces with sandpaper.
$17.86
![Parfix Window Glass Silicone Sealant Interior Exterior [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115942_3d0cfbff-93da-42bb-89d0-8cab3402309a.jpg?v=1754712239&width=645)
Interior and exterior use Acetic cure Excellent bond to glass Parfix Window & Glass Silicone is suitable for use on windows, glass partitions and glass blocks. Ideal for both interior and exterior use, Parfix Window & Glass Silicone is an acetic cure silicone with that bonds securely to glass, providing a water tight and UV resistant seal.
$10.12
The Loctite Super Glue Creative Pen offers the ultimate solution for precise, fast, and reliable bonding. Its ergonomic pen design ensures a controlled application, perfect for intricate tasks like crafting, DIY projects, or quick household repairs. The pen tip provides pinpoint accuracy, so you can apply just the right amount of glue, reducing mess and waste. Loctite’s fast-drying formula creates a strong bond on materials such as wood, plastic, metal, ceramic, and leather, making it versatile for any project. Whether you're fixing a broken ornament, assembling models, or working on craft projects with the kids, Loctite Super Glue Creative Pen guarantees a professional finish every time. LOCTITE® Super Glue Creative Pen Precision bonding on wood, metal, plastic, rubber, and more. Waterproof, weather-resistant, and shock-resistant. Equipped with a long nozzle and easy-grip squeeze bottle for fast and accurate application. Characteristics: LOCTITE® Super Glue Creative Pen is a one-part instant gel adhesive in a convenient dispenser, perfect for home use. It forms strong bonds between a wide range of common materials, including plastics, rubbers, metals, wood, ceramics, leather, fabrics, cardboard, and paper. Its non-drip formula allows for use on vertical or overhead surfaces. The ergonomic pack design ensures precise application, ideal for bonding smaller items. Bonding Speed: Initial adhesion in 5 to 30 seconds, depending on the substrate. Bond Strength (ISO 4587): 10 to 20 N/mm² (tensile shear) in 12 to 24 hours, depending on the substrate. Water-resistant to EN204-D3 standard. Ceramic bonds can withstand over 50 dishwasher cycles under controlled laboratory conditions. Instructions for Use: Ensure all surfaces to be bonded are clean, dry, and fit closely. Twist the cap clockwise onto the pack until you hear a clicking sound. Do not overtighten; a three-quarter turn is sufficient. Avoid skin contact with the glue. Gently squeeze the rubber panels and apply a minimal amount of adhesive to one surface. Press parts together immediately and hold with hand pressure for at least 1 minute. Allow the bond to set undisturbed for 10 minutes, or preferably overnight, to achieve full bond strength. Protect work surfaces and avoid spills. Remove cured glue with LOCTITE® Glue Remover. For best results, apply at room temperature (15-30°C) with at least 30% relative humidity. After use, wipe the nozzle clean with a tissue, replace the cap, and store in a cool, dry place. Technical Data: Composition: Ethyl cyanoacrylate Appearance: Clear gel Density: 1.1 g/cm³ @ 20°C Viscosity: Gel Safety: Refer to SDS 2669372 Shelf Life: 30 months unopened (stored at 2-8°C) Limitations: Do not use on dusty, dirty, or wet surfaces. Not suitable for bonding polypropylene, polyethylene, PTFE, silicone rubber, glass, glazed surfaces, very soft leather, or foams. Do not use for bonding items exposed to hot liquids or high temperatures for extended periods. Optimum performance is achieved in dry conditions. Storage: Store in a cool, dry place, out of reach of children. Why choose Glues Australia? We provide premium-quality adhesives like Loctite, backed by our exceptional customer service. With fast, reliable delivery across Australia, you’ll get the products you need when you need them. Shop confidently with Glues Australia, your trusted adhesive supplier!
$11.57
Loctite Extreme Glue No Drip Gel contains a revolutionary Flextec formulation that fuses multiple materials together for a long-lasting bond. When a project or repair requires an adhesive with a higher viscosity and advanced resistance to extreme conditions, this liquid gel is your new go-to. This versatile, gap-filling glue seals and repairs nearly any surface, and it’s perfect for harsh conditions where constant flexing is a problem. Loctite Extreme Glue No Drip Gel dries clear and minimizes dripping for a clean, professional finish on any household project. It’s even dishwasher safe! Plus, our glue is durable enough to use outdoors because it cures quickly and is resistant to vibration, impact, moisture, UV exposure, and extreme temperatures. No Drip Gel is great for vertical applications Withstands vibration, impact, moisture, and UV light Strong and durable for long-lasting results Use as an indoor or outdoor glue Crystal-clear formula for a clean, professional look Water-resistant and temperature-resistant from -58° to 248° F Gap-filling gel for imperfect-fitting surfaces Flexible bond and precise grip
$10.61
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on: Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone Can be combined with fibreglass cloth for a durable patch Great for crafting projects Properties Will not crack when drilled Can be tinted to match surrounding materials Water resistant: can be used outdoors Does not shrink One-time application Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 5 minutes Quick completion of the project How to Use: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$9.23
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$9.53
GORILLA SUPER GLUE GEL Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time. PRODUCT FEATURES NO RUN CONTROL GEL FORMULA ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use. IMPACT TOUGH: Increase impact resistance and strength FAST-SETTING: Dries in 10-45 seconds, no clamping required VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more! *Not recommended for use on polyethylene or polypropylene plastic or similar materials. DIRECTIONS Protect Work Area From Spills Clean and Dry Surfaces to Be Bonded Prepare Gorilla Super Glue Gel With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle. Apply Gorilla Super Glue Gel Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond. Secure Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure. TECHNICAL SPECS APPLICATION TEMPERATURE – Room temperature SERVICE TEMPERATURE – -53.9°C to 104.4°C OUTDOOR – No PAINTABLE – No SANDABLE – Yes STAINABLE – No EXPANDS WHEN CURED – No CURED COLOR – Clear STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator GAP FILLING – No FAQS Why isn’t my bottle of Gorilla Super Glue filled to the top? For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle. How is Gorilla Super Glue different than Gorilla Glue? Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed. What does Impact Tough mean? Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond. Will Gorilla Super Glue bond plastic/vinyl/rubber? Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds. How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin? To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal. How do I remove Gorilla Super Glue from my surface? To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first. Is Gorilla Super Glue food safe? Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation. What should I do if I think a human or animal ingested Gorilla Super Glue? Additional product safety and first aid information can be found here. How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue? Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key. Why do I need to shake and tap the bottle? Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
$14.99
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$29.36
Glitz Borax is a versatile cleaner and laundry booster that tackles grime, helps remove stains, and deodorises around the home. This mineral based powder dissolves in warm water to lift dirt, cut through residues, and freshen hard surfaces and fabrics. Why you will love it Multi purpose performance for laundry, kitchen, and bathroom Helps remove tough stains and lingering odours Boosts detergent effectiveness in hard water Deodorises bins, drains, and pet areas Free from added fragrance and chlorine Where to use Laundry booster for everyday washing Tiles, grout, sinks, and benchtops Toilets and bathroom surfaces Bins, outdoor furniture, and patios General deodorising tasks How to use Laundry booster: Add 1 to 2 tablespoons to the wash with your usual detergent. For heavily soiled loads use up to 1/4 cup. Dissolve in warm water for best results. Multi surface cleaner: Dissolve 2 tablespoons in 1 litre of warm water. Wipe surfaces with a cloth or sponge. Rinse food contact areas with clean water after cleaning. Stain pre soak: Dissolve 2 tablespoons in 2 litres of warm water. Soak colourfast fabrics for up to 30 minutes. Rinse well before washing as normal. Always patch test first. Deodorising paste: Mix borax with a little water to form a paste. Apply to tiles or grout, lightly scrub, then rinse. Bin and drain freshen: Sprinkle 2 to 3 tablespoons in the bin base or dissolve in warm water and flush down the drain. Rinse thoroughly. Good to know Use on sealed hard surfaces only Check fabric care labels and test on a hidden area first Not suitable for wool, silk, leather, or aluminium What is in the pack Glitz Borax powder 1 kg resealable pack Specifications Product type Multi purpose cleaner and laundry booster Form Free flowing powder Size 1 kg Fragrance None added Safety and storage Read and follow the label before use Wear gloves for prolonged contact Avoid inhaling dust. Use in a well ventilated area Keep out of reach of children and pets Do not ingest. Do not use on skin or as a personal care product Store in a cool dry place with the pouch sealed Disposal Rinse empty packaging and dispose of it in accordance with local council guidelines. Frequently asked questions Can I use it in cold waterYes, but it dissolves more readily in warm water. Pre dissolve in a small amount of warm water when using cold cycles. Is it safe for septic systemsUse sparingly and flush well with plenty of water. Follow any appliance and system guidelines. Will it bleach coloured fabricsIt does not contain chlorine bleach. Always check colourfastness and test on a hidden area first.
$12.22 $9.45
Give everyday cleaning a simple, natural boost with Glitz Bi-Carb Cleaner. This all purpose powder uses the gentle abrasive action and deodorising properties of sodium bicarbonate to lift grime, cut through kitchen film, and freshen household surfaces without added fragrances or dyes. Why you will love it Versatile cleaner for kitchens, bathrooms, laundry, and outdoor touch ups Deodorises fridges, bins, shoes, and pet areas Gentle abrasive action helps remove tea stains, soap scum, and cooked on residue Eco minded choice with a simple, trusted mineral based formula Food area friendly when used as directed, then rinsed well Value size 1kg pack is ideal for regular household cleaning Where to use Benchtops, sinks, stovetops, splashbacks Microwaves, fridges, lunch boxes, drinkware Showers, tiles, grout, basins Bins, pet bowls, outdoor furniture Laundry pre soak for odours in sportswear and towels Car interiors and coolers How to use General cleaning: Sprinkle a small amount onto a damp cloth or sponge. Wipe the surface, then rinse and dry. Stubborn marks: Make a paste with a little water. Apply to the stain, leave for 5 to 10 minutes, then scrub lightly and rinse. Deodorising: Sprinkle directly onto the source of odour, leave for 15 minutes, then vacuum or rinse away. Drains and sinks: Add half a cup followed by hot water to help freshen and reduce build up. Good to know Non scratch on most hard surfaces when used with a soft cloth No added fragrance or dyes Septic safe when used as directed Ingredients Sodium Bicarbonate. Care and safety Test on an inconspicuous area first, especially on delicate finishes and natural stone. Do not use on aluminium, lacquered or highly polished surfaces. Avoid contact with eyes. Keep out of reach of children and pets. Store tightly closed in a cool, dry place. Pack information Brand Glitz Product Bi-Carb Cleaner Natural Eco All Purpose Powder Net weight 1kg Format Fine cleaning powder Country of use Australia Simple tips Refresh chopping boards by applying a paste, scrubbing lightly, then rinsing with warm water. Neutralise fridge odours by placing an open dish in the fridge and replacing monthly. Lift tea and coffee stains in mugs by soaking with a warm water paste for 20 minutes before washing. What customers ask Is it safe on stainless steelYes, use a soft cloth, rub with the grain, then rinse and dry. Can it be used on natural stoneTest first. Rinse thoroughly and dry to protect sealed finishes.
$12.40 $10.11
Cut through stubborn limescale, soap scum, and rust stains with Glitz Calcium Scale and Rust Remover. This powerful bathroom cleaner is formulated to lift mineral build up fast so sinks, taps, tiles, glass, and shower screens look clean and fresh again. The generous 2L size is ideal for whole home maintenance or trade use. Why you will love it Targets tough mineral deposits like calcium, lime, and rust Breaks down soap scum for a brighter, streak free finish Works on ceramic, porcelain, glass, chrome, stainless steel, and most bathroom surfaces Fast acting formula helps reduce scrubbing time 2L value size for households, cleaners, and facilities teams Best for Shower screens and doors Wall tiles and grout surrounds Basins, baths, and toilets on the exterior porcelain Taps, shower heads, and chrome fittings Not recommended for Avoid natural stone like marble, limestone, travertine, or terrazzo. Avoid enamel cookware, unsealed or damaged surfaces, and any surface that states not to use acidic cleaners. If unsure, test on a small hidden area first. How to use Preparation Remove loose debris and pre rinse the surface with warm water. Light scale and soap scum Dilute 1 part product to 4 parts water. Apply with a sponge or spray bottle. Heavy scale and rust stains Use undiluted. Apply directly to the stain and let it sit for 2 to 5 minutes. Do not allow to dry on the surface. Agitate Wipe or scrub with a non scratch pad or soft brush. Rinse well Flush thoroughly with clean water until the surface is neutral and residue free. Repeat if needed For very stubborn deposits, repeat the process in short contact times. Pro tips For shower heads with internal scale, remove the head and soak in a diluted solution. Rinse well before refitting. Squeegee shower glass after each use to slow future build up. Always spot test first. Some finishes are more delicate than others. Safety and handling Wear gloves and eye protection during use Use in a well ventilated area and avoid inhaling mist Do not mix with bleach or ammonia Keep out of reach of children and pets Store upright in a cool, dry place with cap closed After care Once deposits are removed, maintain surfaces with a neutral pH daily cleaner. Regular rinsing and drying will help prevent new mineral build up. Product details Brand Glitz Product Calcium Scale and Rust Remover Bathroom Deep Clean Size 2L Form Liquid Suitable surfaces Ceramic, porcelain, glass, chrome, stainless steel, most glazed tiles Do not use on Natural stone, terrazzo, unsealed or damaged surfaces, acid sensitive finishes Cleanup Rinse with plenty of clean water What is in the box 1 x Glitz Calcium Scale and Rust Remover 2L Good to know Contact time should be short. Rinse thoroughly to protect finishes. For vertical surfaces, apply with a sponge to reduce run off. For regular maintenance, switch to a gentle daily cleaner between deep cleans.
$23.66 $20.12
Keep your kitchen surfaces looking new with a daily cleaner made for modern stone and composite benchtops. This formula lifts grease, fingerprints, and food residue while restoring a natural looking shine. Streak free. No sticky film. Fast to spray, wipe, and finish. Why you will love it Safe for sealed stone surfaces including engineered stone, granite, marble, and quartz Streak free finish that helps reduce dulling and haze Everyday formula that cuts through cooking oils and spills Helps maintain the protective seal of correctly sealed surfaces Low odour for comfortable use in kitchens and living areas Best for Kitchen benchtops and splashbacks Island benches and breakfast bars Polished stone tables and sideboards Bathroom stone vanities and shelves How to use Remove loose crumbs and grit with a dry cloth. Spray a light, even mist over the surface. Wipe with a clean microfibre cloth in overlapping passes. Flip to a dry side and buff to a natural, even shine. Pro tips For heavy spots, leave the spray on the mark for 30 to 60 seconds before wiping. Use a dedicated microfibre cloth for stone to avoid cross contamination. Maintain your benchtop seal as recommended by the surface supplier. Surface compatibility Safe on Not suitable for Sealed engineered stone, sealed granite, sealed marble, sealed quartz, porcelain, ceramic tiles, laminate Unsealed stone, sandstone, limestone, unfinished concrete, waxed or oil finished surfaces Good to know Everyday use. Gentle on properly sealed stone finishes. Leaves a fresh, clean scent that does not linger. Designed to clean. Not a stain remover or etch repair product. Frequently asked questions Can I use it on marbleYes, if the marble is correctly sealed. Always test in a hidden spot first. Is it suitable for food preparation areasYes. Clean the surface, then allow to dry before placing food directly on the benchtop. Will it remove etching or dull spotsNo. Etching is a surface damage issue. Seek professional polishing for that type of repair. How often should I use itUse daily or as needed to keep the surface free of residue and fingerprints. Specifications Finish Streak free, natural looking shine Suitable surfaces Sealed stone and composite benchtops Fragrance Light and fresh Use frequency Daily or as required Application method Spray and wipe with microfibre cloth Safety Read and follow the label directions. Test on a small hidden area before first use. Keep out of reach of children and pets. Do not use on unsealed or acid sensitive stone. Why buy from Glues Australia Curated range for Australian homes and trades Fast dispatch from our local warehouse Helpful support if you need product guidance
$9.91 $7.43
Glitz Daily Shower Cleaner Prevents Soap Scum Build Up 750ml Keep your shower looking fresh with this easy daily spray. Glitz Daily Shower Cleaner helps prevent soap scum and mineral build up so glass, tiles, and fittings stay clearer for longer. No heavy scrubbing required. Just spray and go as part of your routine. Key benefits Helps stop soap scum forming between deep cleans Cuts through light residue from body wash and shampoo Streak free finish on shower screens when used as directed Fast application for busy bathrooms Fresh clean scent that leaves the space smelling pleasant Where to use Shower glass and screens Ceramic tiles and grout surrounds Fibreglass and acrylic bases Chrome and stainless steel fittings Sealed stone and laminate surfaces in wet areas Always test first on an inconspicuous spot. Avoid unsealed stone, marble that is not sealed, brass, copper, and any surface that is not water safe. How to use After showering, quickly rinse surfaces with warm water. Set nozzle to spray. Mist evenly over glass, tiles, and fittings. Leave to work. No rinse required on light residue. For heavier build up, wipe with a soft cloth or squeegee. Use daily to help prevent soap scum returning. Pro tips Keep a squeegee in the shower and pull down glass before spraying for the best clarity. Ventilate the bathroom to reduce fogging and moisture marks. Pair with a weekly deep clean for grout lines and corners. Good to know Non abrasive formula suitable for regular use Safe for most sealed surfaces when used as directed Family friendly routine cleaner for shared bathrooms Specifications Product Daily shower maintenance spray Size 750 ml trigger bottle Suitable surfaces Glass, ceramic tile, acrylic, fibreglass, chrome, stainless steel, sealed stone Finish Clear streak free when wiped or squeegeed Use frequency Daily after showering Safety Read label before use. Keep out of reach of children and pets. Avoid contact with eyes. If contact occurs, rinse with water. Do not mix with other cleaners. Store upright in a cool dry place. Frequently asked questions Do I need to rinse after spraying For light daily residue, no rinse is needed. For visible build up, wipe or squeegee for a clear finish. Will it remove heavy limescale It is designed to prevent and control light residue. For stubborn limescale, use a suitable descaler first then maintain with daily use. Is it safe on natural stone Use only on sealed stone. Test first and avoid unsealed or delicate stone surfaces. What is in the box 1 x 750 ml Glitz Daily Shower Cleaner with adjustable trigger
$11.61 $10.44
Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25L is your everyday helper for a fast, streak free clean. Spray, wipe, and enjoy a bright finish on benches, tables, appliances, and other sealed surfaces around the home. Why you will love it Cuts through daily grime and light grease with ease Leaves a streak free shine on most sealed surfaces Fresh, clean household scent that does not linger No rinsing required on lightly soiled areas Ready to use for quick jobs or dilute for larger areas to save cost Best for Kitchen benches, tables, cupboards, splashbacks Bathroom vanities, tiles, taps, glass shower screens outside surface only Door handles, light switches, appliances exterior, bins Floors when diluted in a bucket for general freshen ups Do not use on Unsealed or waxed timber Natural stone that is unsealed or acid sensitive such as marble and limestone Screen displays or electronics Delicate finishes. Always spot test in a hidden area first How to use Light cleaning. Spray directly onto the surface and wipe with a clean cloth Heavier soil. Let sit for 30 to 60 seconds then wipe. Repeat if required Floors. Add 60 to 100 ml per 5 L of warm water, mop, then allow to dry Glass and glossy areas. Use a lint free cloth and buff dry for best results Quick tips Use separate cloths for kitchen and bathroom to avoid cross contamination For stainless steel, always wipe with the grain and finish with a dry cloth On painted surfaces, apply to cloth first, not directly to the wall Specifications Brand Glitz Product Domestic Cleaner Multi Purpose Surface Shine Format Ready to use liquid. Dilutable for floors Pack size 1.25 L bottle Fragrance Fresh household scent Surface compatibility Most sealed hard surfaces including laminates, sealed stone, ceramic tile, porcelain, stainless steel, enamel, and sealed timber Country of use Suitable for Australian homes and water conditions What is in the box 1 x Glitz Domestic Cleaner Multi Purpose Surface Shine 1.25 L Storage and safety Store upright in a cool, dry place away from direct sunlight Keep out of reach of children and pets Avoid contact with eyes. If in eyes rinse with water Do not ingest. If swallowed seek medical advice Frequently asked questions Can I use it on food contact areas Yes. Clean the surface, then wipe with a damp cloth and allow to dry before food preparation Will it leave residue No when used as directed. Buff with a dry cloth on glass or glossy areas for a crystal finish Is rinsing required Not for light soil. For heavy soil or floors, rinse the mop head regularly for best results Good to know Ideal for quick daily resets in kitchens and bathrooms Economical size that suits family households and shared spaces
$6.51 $6.04
You have seen 48 out of 169 products
Clear and structural options for ceramic and porcelain repairs or installations. For small chips and breaks, consider cyanoacrylates and epoxies; for wet areas, select waterproof and non-corrosive formulas. Check temperature resistance for cookware and ensure full cure before service. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
