UCCC Builders Filler is a polyester resin based filler for filling, building up and smoothing surfaces, supplied here in a 750ml pack. It is made for everyday handy people as well as tradies, and it mixes, applies and sands easily. It suits a wide range of materials, including automotive repair work.About the formulaThis is a thermosetting two-pack polyester filler, so you mix it with its hardener before use. It sets to a hard, sandable finish that holds its shape without shrinking. The paste is off-white or beige-brown. It can be applied to horizontal or vertical surfaces. Once cured, it can be painted or stained.Where to use itIndoors: filling and levelling timber, repairing dents and gaps in metal, and general building and renovation repairs.Outdoors: repairs on exterior timber, concrete, metal and fibreglass. The cured filler is UV resistant.Automotive: suitable for body repair work.Suitable materials include metals (including galvanised steel), concrete, fibreglass and timber, plus many other substrates. As with any filler, test a small area first if you are unsure about a particular surface.How to use itMake sure the surface is clean, dry and free of grease, dust, loose paint and rust. Sand or key smooth surfaces for a better grip. Mix only as much filler as you can use in one go, blending in the hardener thoroughly as directed on the pack. Press the mixed filler firmly into the repair, working it in to avoid air pockets. Build it slightly proud of the surface, then let it harden fully. Sand it flush and smooth, then prime and paint or stain as needed.Important notesAlways follow the mixing directions on the pack, because the amount of hardener affects how quickly the filler sets and how well it cures. Warm conditions speed up setting and cool conditions slow it down. The filler is dry to touch in about 20 minutes, and you should sand it only once it has hardened properly. Close the tin tightly after use. Hardened filler cannot be reused.Specifications Brand UCCC Product Builders Filler Size 750ml Colour Off-white or beige-brown Base Polyester resin, two-pack (mixed with hardener) Application Hand applied with a spreader or putty knife Dry to touch About 20 minutes Finish Sandable, paintable and stainable Properties Shrink resistant, UV resistant Use Interior and exterior SafetyUse with normal care. Work in a well-ventilated area, keep away from heat and open flame, and avoid contact with eyes and skin. Wear gloves and safety glasses, and use a dust mask when sanding. Keep out of reach of children and store in a cool, dry place with the lid tightly closed. Refer to the Safety Data Sheet (SDS) for full details.
$26.23
Selleys Tradie's Bog is a fast-setting, two part polyester building filler for repairing timber and most common building materials, supplied here in a 550g pack. It is built for quick, hard-wearing repairs where a lightweight filler would not hold up, and it can be sawn, drilled, sanded and painted once set. About the formulaA cream polyester resin paste that you mix with the supplied hardener to start the cure. It grips well to a wide range of building surfaces and sets hard in around 20 minutes, with minimal shrinkage, so you can shape it, sand it and move on to painting quickly. The cream base can be tinted with cement oxides or paint tinters if you add the colour before the hardener. Where to use itIndoors: repairing window and door frames, architraves, skirting boards and sashes, and filling holes, cracks and damaged edges in timber and plasterboard.Outdoors: patching external timber joinery, masonry, concrete and metal, then finishing with a suitable paint system. Suitable materials include timber, plasterboard, concrete, brick, fibreglass, metal, alloy, tiles and ceramics. How to use itMake sure the area to be repaired is clean, dry, unpainted and free of oil and grease. Stir the bog before use, then work out a short ribbon of hardener (about 2.5cm for every heaped tablespoon, or roughly 20g, of bog) and mix thoroughly on a clean surface until the colour is even. Press the mix into the repair with a spatula and overfill slightly. For dents in steel or aluminium that will see heavy vibration, punching or drilling the metal first gives the filler a better key. Shape off the excess with a Surform or rasp before it goes rock hard, then use ordinary files or sandpaper once fully set. Clean tools with mineral turpentine before the product cures. Important notesWorking time is about 5 minutes at 23°C, so mix only what you can apply straight away. The filler is rigid, so it is not suited to joints or areas where movement is expected, nor to areas under constant water immersion. It will not bond to polyethylene, polypropylene or PTFE (Teflon). Colour must be added before the hardener. The filler can be painted once cured. Specifications Brand Selleys Product Tradie's Bog Two Part Polyester Building Filler Pack 550g (filler with hardener) Colour Cream Base Two part polyester Application Mixed by hand and applied with a spatula Work time About 5 minutes at 23°C Cure time About 20 minutes Finishing Can be sawn, drilled, tapped, sanded and painted Clean up Mineral turpentine (before cure) Use Interior and exterior SafetyUse in a well-ventilated area, away from heat and open flame, and wear gloves and safety glasses when mixing and sanding. Avoid contact with skin and eyes. Keep out of reach of children and store the pack tightly closed in a cool, dry place out of direct sunlight. Refer to the Safety Data Sheet (SDS) for full details.
$32.71
Sika SikaBond 142 Instant Nails is a high-strength, multipurpose construction adhesive for fixing panels, timber and sheeting, supplied here as a trade pack of twelve 300g cartridges for busy sites and larger renovation jobs. It is a ready-to-use, single-component adhesive with a thick body that stays put on vertical surfaces, so it suits fixing work where you would otherwise reach for extra nails or screws.About the formulaA one-component synthetic rubber adhesive in a beige, non-slump paste. It can be used as a one-way adhesive (apply to one surface and join straight away) or as a two-way contact adhesive (apply, press together, separate, let it skin, then rejoin). It has a short skinning time of about 1 to 5 minutes, and a bond that develops quickly. The cured adhesive can be painted over.Where to use itIndoors: floor and wall panels, timber, particleboard, MDF and plywood fixed to frames, plus plasterboard and similar sheet linings.Outdoors: cement sheeting, fibreglass, concrete and masonry fixing jobs that are not constantly wet or immersed.Suitable materials include floor and wall panels, timber, particleboard, MDF, plywood, plasterboard, aluminium, iron and steel, concrete, cement sheeting, fibreglass and masonry. Test an offcut first if you are working with a material that is not on this list.How to use itMake sure surfaces are sound, clean, dry and free of dust, oil, grease and loose material. Cut the nozzle and apply the adhesive in a bead with a standard caulking gun. For the one-way method, bring the surfaces together straight away and press firmly. For the two-way method, press the surfaces together to transfer the adhesive, pull them apart, wait for it to skin over, then rejoin them with firm pressure. Tapping the work with a hammer and a padded block helps ensure full contact. Heavy panels may need temporary mechanical fixing until the bond has developed. Clean tools straight away with Sika Colma Cleaner or mineral turpentine. Once cured, the adhesive can only be removed mechanically.Important notesMaximum bond strength is reached in about 12 to 72 hours, and full cure takes about 7 days depending on weather conditions. Do not use it for immersed applications, do not apply it when the temperature is below 5°C, and avoid damp, unseasoned or treated timber. Store unopened cartridges in a dry place between 5°C and 25°C. Shelf life is 18 months from the production date.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 12 x 300g cartridges Colour Beige Base One-component synthetic rubber, solvent-based Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Maximum bond strength 12 to 72 hours Full cure About 7 days Yield About 15 linear metres per cartridge (continuous 5mm bead) Service temperature 0°C to 40°C Application temperature 5°C to 40°C (substrate) Shelf life 18 months SafetyUse with normal care: work in a well-ventilated area, keep away from heat, sparks and open flame, and avoid contact with skin and eyes by wearing gloves and safety glasses. Keep out of reach of children and store the cartridges in a cool, dry place with the nozzle capped. Refer to the Safety Data Sheet (SDS) for full details.
$60.05
SikaBond-142 Instant Nails is a high strength, multipurpose construction adhesive that holds its place on vertical surfaces, supplied here as a trade pack of six 300g cartridges. It works as a one-way liquid adhesive or as a two-way contact adhesive, so it suits quick panel fixing as well as bonding jobs where you want an immediate grab.About the formulaA one-component, ready-to-use synthetic rubber dispersion in a beige, non-slump paste. The bead stays put on walls and ceilings instead of sagging, skins over within about 1 to 5 minutes and dries quickly. The Sika data sheet reports tensile strength above 1 MPa on a dry substrate (tested to AS 2329) and peel adhesion above 40 N. Once cured, it can be painted over.Where to use itIndoors: floor and wall panels, skirting and trim, and panelling fixed to timber or metal backing.Outdoors: Sika does not list exterior use on its data sheet, so check suitability for your application before using it outside. It is not suitable for permanently immersed applications.Suitable materials include timber, particleboard, MDF, plywood and plasterboard, aluminium, iron and steel, and concrete, cement sheeting, fibreglass and masonry.How to use itSurfaces should be clean, sound and dry, with oil, grease, dust and loose flaking material removed. Light abrasion helps adhesion. Load a cartridge into a standard caulking gun and apply a bead. For one-way use, press the panel into place. For two-way contact bonding, coat both surfaces, allow the adhesive to skin over, then press together firmly. Apply only when the surface temperature is between 5°C and 40°C.Important notesFull cure takes about 7 days, depending on weather conditions. Do not apply below 5°C, and do not use on damp, unseasoned or treated timber. Service temperature range is 0°C to 40°C. Not suitable for immersed applications. Test on an offcut first if you are unsure about a surface.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 6 x 300g cartridges Colour Beige Base 1-component synthetic rubber dispersion Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Full cure About 7 days Yield About 15 linear metres per cartridge (continuous 5mm bead) Application temperature Substrate 5°C to 40°C Service temperature 0°C to 40°C Shelf life 18 months from production, stored unopened Standard Tensile strength tested to AS 2329 SafetyUse with normal care: work in a well-ventilated area, keep away from heat and open flame, and avoid contact with skin and eyes by wearing gloves and safety glasses. Keep out of reach of children and store unopened cartridges in a dry place between 5°C and 25°C. Refer to the Safety Data Sheet (SDS) for full details.
$31.19
Soudal Bathroom & Kitchen Neutral Cure Silicone in clear is a pure silicone sanitary sealant for wet areas, supplied as a 300ml cartridge for use in a standard caulking gun. It is built for the joints that take the most punishment around showers, baths, sinks and benchtops, giving a waterproof seal that stays flexible and resists mould and mildew.About the formulaA neutral cure, non-corrosive silicone made from pure silicone with no extenders. It contains fungicides to help the seal resist mould and mildew in demanding sanitary conditions. It is easy to apply and tool, has a longer working time for smoothing joints, and stays permanently elastic once cured. The cured seal is colourfast and UV resistant, with a low modulus and a joint movement capability of +/- 25%.Where to use itIndoors: joints around bathtubs, vanities, shower screens, sinks, basins and toilets, kitchen splashbacks and benchtop joints, and sealing around plumbing fixtures in kitchens, bathrooms and laundries.Outdoors: not specifically recommended by the manufacturer for this product. Check the manufacturer data sheet or choose a product made for exterior use.Suitable materials include glass, tiles, fibreglass, vitreous enamel and many other common building and sanitary surfaces. Test an inconspicuous area first on any surface you are unsure about.How to use itMake sure the joint is clean, dry and free of dust, grease, soap scum and old sealant. Cut the nozzle to suit the joint, load the cartridge into a caulking gun and apply a steady, continuous bead. Smooth the bead with a profiling tool or a soapy water solution before the surface skins over, then remove any masking tape. Wipe away uncured excess promptly. Once cured, silicone has to be cut or scraped away.Important notesCure time depends on temperature, humidity and bead thickness, so allow plenty of time before exposing the joint to water. Keep joints well ventilated while curing. Always follow the manufacturer's instructions and test compatibility on sensitive materials before sealing.Specifications Brand Soudal Product Bathroom & Kitchen Neutral Cure Silicone Pack 300ml cartridge Colour Clear Base 100% silicone, neutral cure, no extenders Application Cartridge, via caulking gun Movement capability +/- 25% Key features Mould resistant, waterproof, non-corrosive, colourfast and UV resistant Use Bathrooms, kitchens and other wet areas SafetyWash exposed skin thoroughly after handling and wear suitable gloves and eye protection. Store locked up and dispose of contents and container in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$10.38
Sika Sikasil Auto is a neutral-cure, one-component silicone adhesive sealant made for vehicle repair and trim work, supplied here in a handy 75g tube. It forms a permanent, flexible bond or seal on a wide range of automotive materials, and the cured rubber copes with sunlight, salt spray, temperature swings, vibration and regular car-wash products without hardening, shrinking or cracking.About the formulaA moisture-curing, one-component silicone with a neutral cure, so it does not give off the acidic smell of acetic silicones and is described by the manufacturer as non-corrosive. It cures by reacting with moisture in the air, starting at the surface and working into the core of the joint. Cure speed depends on humidity and temperature, and it cures more slowly in cold conditions. Once cured it is a soft, stretchy rubber with strong thermal, UV, weathering and vibration resistance, and it stays serviceable from -50°C up to 250°C.Where to use itIndoors: bonding small interior components and trim, sealing joints, and cutting down noise and vibration inside the vehicle.Outdoors: sealing and bonding small exterior parts and joints on cars and other vehicles where weather, UV and salt spray are a concern.Suitable materials include fibreglass, metals, most plastics, glass and painted surfaces. Always test on the actual substrates and under your real conditions first to confirm adhesion and material compatibility.How to use itApply at ambient temperatures between 5°C and 45°C onto clean, dry surfaces that are free of oil, grease and dust. Run the sealant into the joint or onto the part and assemble or tool it before it skins over. At 23°C and 50% relative humidity it skins in about 10 minutes and is tack free in about 20 minutes. Excess uncured sealant can be wiped off with Sika Remover-208 or a similar product. Cured sealant has to be trimmed or scraped away mechanically. If you get it on your skin, wash straight away with SikaCleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.Important notesSikasil Auto cannot be overpainted, so complete any painting before sealing or mask the area. It cures to a depth of about 3 mm in 24 hours, so deeper joints and thicker beads take longer. Check the manufacturer's data sheet for any surfaces or applications where the product is not recommended. This product is designed for vehicle applications. Test first on a small area before committing to the full job.Specifications Brand Sika Product Sikasil Auto Multipurpose Automotive Adhesive Sealant Pack 75g tube Colour Translucent Chemical base 1-component silicone, neutral cure, moisture-curing Application Tube, applied by hand Application temperature 5 to 45°C ambient Skin time About 10 minutes (23°C, 50% r.h.) Tack free time About 20 minutes (23°C, 50% r.h.) Cure speed About 24 hours to a 3 mm depth Density (uncured) 1.0 kg/L Shore A hardness 30 Tensile strength 1.0 N/mm² Elongation at break 600% Service temperature -50 to 250°C Shelf life 18 months when stored below 25°C Use Vehicle interior and exterior SafetyFollow normal good practice for silicone sealants: work in a well-ventilated area, wear gloves and eye protection, and keep out of reach of children. Wash skin promptly after contact using an industrial hand cleaner and water, and do not use solvents on skin. Store in the original sealed tube below 25°C. Refer to the Safety Data Sheet (SDS) for full details.
$17.37
Permastik Fly Screen Repair Tape is a simple, low-cost way to fix small holes and tears in a flyscreen without replacing the whole screen, supplied here as a 5m x 50mm black roll. You cut a patch to suit the damage and stick it on, so one roll covers plenty of small repairs around the house.About the productA self-adhesive repair tape in a black finish, made from fibreglass material. It comes on a long roll rather than as pre-cut patches, so you can size each patch to the hole instead of being tied to a fixed patch size. The black colour suits standard dark flyscreen mesh.Where to use itIndoors and around the home: patching small holes, rips and tears in window and door flyscreens, and in similar fibreglass insect screens, as an easy fix until the screen is due for a full re-screen.Outdoors: the screen being repaired may be on an outside window or door, but the manufacturer does not publish weather or UV ratings for the tape itself, so treat it as a quick repair rather than a permanent one.Designed for fibreglass flyscreen mesh. Test on an inconspicuous corner first if your screen is made from a different material.How to use itMeasure the hole or tear and cut a piece of tape large enough to cover it with some overlap. Peel off the backing, position the patch over the damage and press it down firmly so the adhesive makes full contact with the screen. A clean, dry screen surface helps the patch stay in place.Important notesThis is a repair for small holes and tears, not for large damaged areas, where re-screening is the better option. The patch will be visible on the screen. The manufacturer does not publish adhesive cure times or temperature limits, so avoid heavy stress on the repair straight after fitting.Specifications Brand Permastik Product Fly Screen Repair Tape Manufacturer model number 73 Size 5m x 50mm roll Colour Black Material Fibreglass Application Hand applied, self-adhesive, cut to size Use Repair of small holes and tears in flyscreens SafetyKeep out of reach of young children. Refer to the Safety Data Sheet (SDS) for full details.
$11.64
Protite Fibreglass Chopped Matting is a strand-chopped glass fibre mat that adds strength and reinforcement to fibreglass repairs, supplied here as a 1m x 1m sheet. It is an economical, general-purpose reinforcement for boats, caravans, trailers, surfboards, gutters, downpipes and water tanks. It is designed to be laminated with Protite Fibreglass Resin and Protite Resin Catalyst Hardener.About the materialThe mat is made from strands of glass fibre laid randomly across each other and bound together. The loose, random layout gives similar stiffness in every direction, and the mat conforms to tight curves and corners more readily than woven cloth. It is a 450gsm mat with a rough finish. It suits general, non-structural repair and lay-up work. Protite recommends it for adding strength and rigidity to repairs. Woven cloth gives a smoother and more flexible finish if that is what the job needs.Where to use itIndoors: general fibreglass repair and reinforcement on rigid items such as moulded parts, timber and other suitable substrates.Outdoors: down pipes, leaky gutters, metal roofs and rusted panels, plus boats, caravans, trailers, surfboards and water tanks.Protite lists steel, iron, aluminium, timber, PVC, masonry and smooth polyester or wooden surfaces as suitable for repair with its fibreglass system. As with any repair, check the resin instructions and test a small area first on unusual substrates.How to use itPrepare the surface so it is clean, dry and sanded or keyed as the resin instructions advise. Cut the mat to the repair shape and allow for an overlap of about 3cm around the damage. Tease out the fibres at the edge to create a feathered edge that blends in. Mix only as much resin and hardener as you can use quickly, following the ratios on the resin pack, because it begins to gel and cure once the hardener is added. Apply a wet coat of resin to the surface, lay the mat in place, then dab more resin over the top without brushing, so the mat does not shift. Make sure the fibres are fully wetted out. Gently roll out trapped air with a fibreglass roller, then leave the resin to cure fully before sanding, filling and painting.Important notesThe mat is a reinforcement only and needs compatible polyester resin and hardener to form a repair (both sold separately). Cure times depend on the resin, the amount of hardener and the temperature, so follow the resin pack. Cut ends and sanded surfaces release fine glass fibres, so avoid breathing the dust and wear suitable protection. A finished repair can be sanded and painted.Specifications Brand Protite Product Fibreglass Chopped Matting Size 1m x 1m (1m²) Material Strand-chopped fibreglass mat Weight of mat 450gsm Finish Rough Appearance Yellow to white fibres bound together in strands Use with Protite Fibreglass Resin and Protite Resin Catalyst Hardener Application Hand lay-up, cut to shape and wetted out with resin Use Interior and exterior SafetyAvoid breathing in fibres or dust, work in a well-ventilated area, and use mechanical extraction at the source if power tools are used for cutting or sanding. Do not let the product enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$42.20
The Protite Large Fibreglass Repair Kit is an all-in-one pack for patching cracks, dents and holes in fibreglass, metal and timber, with a 1kg tub of resin and 1m² of chopped strand matting for bigger repair jobs. Everything needed to mix, lay up and finish a repair is in the box, so it suits boat, caravan, car, surfboard and household fixes alike.About the formulaThe resin is a polyester, low styrene emission (LSE) type, made to give good strength, adhesion and an easy-wetting consistency on most repair jobs. It is cured with the supplied catalyst hardener, which starts the setting reaction. The chopped strand matting adds rigidity and reinforcement and conforms easily to tight curves and corners. Once cured, the repair is water resistant, sandable and paintable, and the resin can be tinted with paint (up to 5%) for a solid colour match.Where to use itIndoors: repairs to fibreglass items, timber and other household surfaces, plus craft and workshop fixes such as surfboard repair.Outdoors: caravans, boats, trailers, bikes and cars, fibreglass pools, water tanks and water skis, downpipes, leaky gutters, metal roofs and rusted panels.Suitable materials include fibreglass, steel, iron, aluminium, timber, PVC, masonry and smooth polyester or wooden surfaces.What is in the kit Fibreglass resin, 1kg Fibreglass chopped matting, 1m² Fibreglass resin catalyst hardener, 15ml (dropper bottle) Nitrile gloves Measuring cup Applicator brush Mixing stick Mixing bucket How to use itAbrade the damaged area and clean it, removing loose debris and old paint, because poor surface preparation is the usual cause of failed repairs. Cut the matting to size, then mix the resin and hardener in the supplied bucket, stirring for at least two minutes and scraping the bottom and sides so it mixes evenly. If you want to tint the resin, add the paint tint before the hardener. Brush a coat of mixed resin over the repair, lay the matting into it, then saturate the matting with more resin, dabbing to push out air pockets. Add further layers while the previous one is still wet, or lightly sand a cured layer before adding the next. Leave the repair to cure fully (the manufacturer states about 24 hours), then sand smooth and paint if required.Important notesAlways follow the mixing instructions on the pack. Under-mixing leaves soft, uncured patches. Epoxy resin can be applied over fully cured, dewaxed and well-sanded polyester, but polyester should never be used over cured epoxy. Cure time is slower in cold weather. Use in a well-ventilated area and avoid breathing in sanding dust once cured.Specifications Brand Protite Product Large Fibreglass Repair Kit (model PF-FKIT1000) Pack 1 kit: 1kg resin, 1m² chopped matting, 15ml hardener and application tools Resin type Polyester, low styrene emission (LSE) Application Brush, hand lay-up with supplied tools Full cure About 24 hours (manufacturer guide) Finish Sandable and paintable Use Interior and exterior; water resistant, UV resistant, shrink resistant Kit dimensions Approx. 215 x 215 x 197mm SafetyKeep it away from heat, sparks and open flames. Wear the supplied nitrile gloves plus eye protection, work in a well-ventilated area and avoid breathing vapour. Store in a cool place away from heat and direct sunlight, keep out of reach of children and dispose of waste responsibly. Refer to the Safety Data Sheet (SDS) for full details.
$68.67
Turbo Metal Builders Bog is a two part, aluminium and glass fibre reinforced polyester filler for rusted metal, dents, cracks, holes and tears, supplied here as a 500ml can. It is aimed at panel beaters, builders and DIYers who want a hard, workable repair that can go over or under ordinary body filler for extra strength, and which also works on fibreglass, wood, stone, concrete and aluminium.About the formulaThe filler is a paste based on unsaturated polyester resin in styrene, loaded with aluminium so you can repair metal with a metal-filled compound, and with glass fibre strands that help bridge holes and gaps. Once catalysed with a separate peroxide-based hardener, the mix gels to a cheese-like consistency that can be cut, shaped or pared, then cures hard. Changing the amount of hardener lets you speed up or slow down the set to suit the job and the weather. Turbo describes it as having minimal shrinkage, good stress resistance and flexibility, water resistance and rust-inhibiting properties.Where to use itIndoors: repairing holes, cracks and damaged areas in fibreglass, wood, stone and concrete, and filling larger voids where a standard filler would sag or shrink.Outdoors: rusted-out panels, dents and holes in metal, vehicle bodywork and similar repairs, plus cracked or broken concrete, masonry and aluminium items exposed to weather.Suitable materials include steel and other metals, aluminium, fibreglass, wood, stone, concrete and masonry. It can be used instead of, or underneath, regular plastic body filler.How to use itStart with a clean, dry, sound surface, free of loose rust, paint, oil, grease and dust, and roughen smooth surfaces for a better key. Work out how much filler you need and mix it with the hardener following the directions on the can, stirring until the colour is completely uniform. Because cure speed depends on temperature and the amount of hardener, try a small batch first. Press the mix firmly into the repair, building up and shaping it while it is still soft. Once it has gelled you can trim it, then sand, file, drill, machine and paint it after it has cured hard.Important notesThis is a two part system and will not cure without the hardener, so check the hardener is on hand before you start. More hardener or warmer conditions will shorten the working time, and less hardener will lengthen it. Full cure is typically within about 30 to 60 minutes, and the repair can be painted within the hour, though times vary with temperature and mix. The cured filler is paintable but not stainable. For large structural repairs on metal, make sure the underlying area is sound.Specifications Brand Turbo Product Metal Builders Bog (metallised repairer) Size 500ml can Colour Grey Base Unsaturated polyester resin filler with aluminium and glass fibre Application Hand applied after mixing with hardener Set and cure Gels to a cheese-like consistency, full cure typically about 30 to 60 minutes (varies with hardener and temperature) Paintable Yes, within the hour Sandable Yes Stainable No Shrink resistant Yes UV resistant Yes Use Interior and exterior SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use outdoors or in a well-ventilated area, avoid breathing vapours, and avoid contact with eyes, skin and clothing. Wear suitable gloves and eye protection. Wash exposed skin thoroughly after handling and remove contaminated clothing. Refer to the Safety Data Sheet (SDS) for full details.
$32.41
The Deks Rapid Flash Self-Adhesive Repair Strip is a lead-free, black flashing strip made for quick, temporary fixes to leaking roofs and gutters, supplied as a single 140mm x 500mm strip. It is a handy item to keep on hand when you need to stop a leak from a cracked tile or a damaged gutter until a permanent repair can be done.About the formulaThe strip is made from a rubber-based polymer with an integrated aluminium mesh. It has a fully adhesive base, so it goes on without separate sealants or fixings. The black finish suits most roof colours and materials. Deks lists the strip as suitable for all roof and gutter profiles and for most roof and gutter materials. It is lead-free, and you can cut it to size with heavy-duty scissors.Where to use itIndoors: not intended for interior use.Outdoors: temporary repairs to leaking gutters, cracked roof tiles and other roof leaks on a range of roof profiles and materials.Suitable materials include metal roofing and gutters, tile roofs and fibreglass sheeting. Deks describes the strip as suiting most roof and gutter materials, so test a small area first on unusual or heavily weathered surfaces.How to use itClean the repair area and let it dry fully, removing dirt, dust, loose debris and flaking material. Measure the area to be covered and cut the strip to length with heavy-duty scissors. Remove the backing from the adhesive face, position the strip over the leak and press it down firmly, working it into the roof or gutter profile so the adhesive bonds across the whole contact area. Always follow any instructions that come with the pack.Important notesThis is designed as a quick, temporary repair, so plan a permanent fix when conditions allow. Surface preparation matters, because the adhesive needs a clean, dry surface to grip. Take care when working at height, and be careful with cut edges of the aluminium mesh.Specifications Brand Deks Product Rapid Flash Self-Adhesive Repair Strip Pack 1 strip Size 140mm wide x 500mm long Thickness 2.3mm Colour Black Material Rubber-based polymer with integrated aluminium mesh Application Hand applied, self-adhesive backing, cut to size with heavy-duty scissors Lead content Lead-free Listed certifications AS 1530.8.1 (as listed by Deks), AS/NZS 2904, ASTM D7238, ASTM G154, BAL 19, BBA Use Exterior roof and gutter repairs (temporary) SafetyWear gloves when cutting and handling the strip, and watch for sharp mesh edges. Store the strip flat or rolled in a cool, dry place out of direct sun until you need it. Refer to the Safety Data Sheet (SDS) for full details.
$24.22
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in white is a ready-to-spray rubberised coating for sealing leaks and cracks around the home, supplied here as a single 340g aerosol can. It lays down a firm but flexible, watertight layer that helps keep out water, air and moisture, and it also protects the coated surface from rust. It suits quick repairs on gutters, roofing, flashing and ductwork without mixing, brushing or special tools.About the formulaA solvent-borne, hydrocarbon resin coating that sprays on and builds up to fill small gaps and cracks (the manufacturer lists gaps and cracks up to 6.35mm). It dries to a semi-smooth, firm finish that stays flexible and is designed not to sag or drip, so it holds its shape on sloped and vertical surfaces. Once cured it can be top-coated with latex or oil-based paints, which makes it easy to blend repairs into the surrounding colour scheme.Where to use itIndoors: sealing cracks and leaks in ductwork, pipework surrounds and other protected areas, with good ventilation while you spray.Outdoors: patching gutters, flashing, metal roofing, downpipes, masonry and concrete surfaces that need a flexible waterproof barrier.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Do a small test spray first if you are unsure about a surface.How to use it Prepare the surface by washing it with a detergent and water solution, rinsing well and letting it dry fully. Lightly sand glossy surfaces and wipe off the dust. Mask off nearby areas to protect against overspray. Spray outdoors or in a well-ventilated space, ideally when the temperature is between 10 and 32 degrees Celsius and humidity is below 65%. Avoid very windy or dusty conditions, and allow more drying time in cooler weather. Shake the can vigorously for about one minute once the mixing ball starts to rattle, and shake it often while you work. Do a test spray on cardboard to get a feel for the spray pattern, then hold the can 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a second heavier coat for full coverage. Moving the can closer builds a thicker film. Some foaming or bubbling at first is normal and settles as the coating dries. After use, turn the can upside down and press the nozzle until only clear propellant sprays out. If the valve clogs, remove the spray tip and rinse it in mineral turpentine. Never push an object into the valve opening. Clean wet or dry coating with mineral turpentine or xylene. Important notesNot recommended for rubber surfaces or for surfaces that sit in continuous water immersion. Under the manufacturer's data, touch dry is about 2 hours at 21 to 27 degrees Celsius and 50% humidity, further coats can go on after 15 to 30 minutes, and you should allow 24 hours for a full cure and before top-coating. Cooler or more humid conditions will slow drying. This is not a fire or high-heat resistant coating. Shelf life is listed as 5 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour White Base Solvent-borne, hydrocarbon resin Application Aerosol spray Gap and crack fill Up to 6.35mm Touch dry About 2 hours (21 to 27°C, 50% RH) Recoat 15 to 30 minutes Handle 2 to 3 hours Full cure / topcoat 24 hours Practical coverage About 0.37 to 0.46 m² per can at a thick 125 micron film, or about 0.74 to 0.93 m² per can at 62.5 microns (manufacturer figures allowing for 15% material loss) Paintable Yes, with latex or oil-based paints Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. Contents are under pressure, so do not pierce or burn the can, even when empty. Use only outdoors or in a well-ventilated area, and avoid breathing the spray, mist or vapour. Refer to the Safety Data Sheet (SDS) for full details.
$23.95
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in Black is a ready-to-use aerosol sealer for stopping leaks and sealing cracks around the home, workshop and site, supplied here as a single 340g can. It sprays on as a rubberised coating that builds a flexible, water-tight barrier over a wide range of common building surfaces, which makes it a quick fix for hard-to-reach or awkward spots where a caulking gun is difficult to use.About the formulaA solvent-based, hydrocarbon resin rubber coating that sprays on as a high-build film. It dries to a firm, semi-smooth black finish that stays flexible and is formulated not to sag or drip. The cured coating helps block moisture and protects against rust and corrosion, and it can be top-coated with acrylic (latex) or oil-based paints once cured.Where to use itIndoors: ductwork, pipes, air conditioner drip pans, vents and other protected areas where a flexible waterproof seal is needed (use only with good ventilation).Outdoors: gutters, downpipes, roof sheeting, flashing, skylight surrounds, metal sheds and buildings, and concrete or masonry surfaces where cracks or small holes let water in.Suitable surfaces include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Always do a small test spray on an inconspicuous area first, particularly on plastics.How to use itPrepare the surface so it is clean, dry and free of loose material, dirt, grease and flaking paint. Do a test spray on a piece of cardboard first to get a feel for the spray pattern, then apply the coating over the leak or crack using even passes, following the directions on the can. Additional coats can be applied after 15 to 30 minutes if a heavier build is needed. Once cured, the surface can be top-coated with acrylic or oil-based paint. Use outdoors or in a well-ventilated area.Important notesThe coating is touch dry in about 2 hours, can be recoated with itself after 15 to 30 minutes, and can be top-coated after 24 hours (times based on roughly 21 to 27°C and 50% relative humidity, so allow longer in cool or humid conditions). It is not intended for surfaces under continuous water immersion. It is not rated as fire or high-heat resistant, and it is not a mould or mildew-resistant coating. Coverage depends on the film thickness applied: about 0.74 square metres per can at a thin film (62.5 microns) or about 0.37 square metres per can at a thicker film (125 microns), allowing for typical material loss. Shelf life is around 2 to 3 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour Black Finish Semi-smooth, firm, flexible Base Solvent-based, hydrocarbon resin Application Aerosol spray Touch dry About 2 hours Recoat (with itself) 15 to 30 minutes Top-coat with paint After 24 hours Full cure About 24 hours Coverage per can About 0.74 m² at 62.5 micron, or 0.37 m² at 125 micron Paintable Yes, acrylic (latex) or oil-based paints Use Interior and exterior SafetyUse only outdoors or in a well-ventilated area, keep away from heat, sparks, flame and other ignition sources, and wear protective gloves, protective clothing, and eye and face protection. Store the can away from heat and do not store above 49°C. Refer to the Safety Data Sheet (SDS) for full details.
$27.92
Rust-Oleum LeakSeal Clear is a rubberised spray-on sealant that stops leaks and seals cracks in one easy aerosol, supplied here as a single 312g can. It lays down a flexible, water-tight coating over gutters, roofing, flashings, ducting and more, and the clear finish lets the original surface show through. It suits homeowners and maintenance tradies who need a quick, no-fuss repair.About the formulaA solvent-based, rubberised coating built on a hydrocarbon resin, delivered by a flammable propellant. It sprays on as a firm but flexible film that fills small gaps, cracks and holes (the manufacturer rates it for gaps up to about 6mm) and forms a barrier against water, air and moisture. It dries to a semi-smooth finish that does not sag or drip, helps protect the surface from rust, and can be topcoated with latex or oil-based paint once cured.Where to use itIndoors: ductwork, vents, pipes and other surfaces that need a flexible moisture seal.Outdoors: gutters, downpipes, roof flashings, metal roofing, sheds, vents and cracked masonry or concrete.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Test a small hidden area first on any surface you are unsure about.How to use itRemove all dirt and debris from the repair area. The manufacturer's technical data also advises washing with detergent and water, rinsing and letting the surface dry thoroughly, removing loose paint or old coatings, and lightly sanding glossy surfaces. Mask off surrounding areas to protect them from overspray.Apply outdoors or in a well-ventilated space, ideally between 10 and 32°C with humidity below 65%. Avoid very windy or dusty conditions.Shake the can vigorously for one minute after the mixing ball starts to rattle, and shake often during use. Do a test spray on cardboard to get a feel for the pattern.Hold the can about 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a heavier second coat for full coverage. Moving closer to the surface builds a thicker film.Once the coating has fully cured, it can be painted with latex or oil-based paint if you want it to match the surroundings.Important notesDry to touch in about 30 minutes, with full cure in about 24 hours. Not recommended for rubber surfaces or for surfaces under continuous water immersion. It is not fire or high-heat resistant and is not rated as mould or mildew resistant. Coverage varies with surface porosity and how thick you apply it. Do not apply to hot surfaces.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 312g aerosol can Colour Clear Base Solvent-based, hydrocarbon resin Application Aerosol spray Dry to touch About 30 minutes Full cure About 24 hours Maximum gap or crack size Up to about 6mm Application temperature 10 to 32°C Paintable Yes, with latex or oil-based paint Flexibility Remains flexible Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. The can is pressurised: do not pierce or burn it, even when empty, and do not expose it to temperatures above 50°C. Use outdoors or with good cross-ventilation. Refer to the Safety Data Sheet (SDS) for full details.
$23.25
Tricleanium Adhesive Remover is a solvent-based cleaning agent for lifting stubborn sticky residue, supplied here in a 500ml bottle for both household and trade clean-ups. It is made for the leftovers that soap and water will not shift, including stickers, labels, gum, tar, crayon and tape or glue residue, so you can clean up without hard scraping.About the formulaThis is a fast-acting, solvent-based liquid that softens sticky build-up so it can be wiped, blotted or rinsed away. The manufacturer's safety data sheet describes it as a dark yellow liquid and lists ethanol and dipentene in its transport entry. It is a flammable liquid, so treat it with the same care you would any solvent product.Where to use itIndoors: removing label, sticker and tape residue from glass, metal, timber and tiled surfaces, and lifting gum, grease and sticky marks on hard surfaces around the home or workshop.Outdoors: cleaning adhesive, tar, carbon and other stubborn build-up from porous surfaces such as brick, concrete, terrazzo, marble and granite, and from vinyl siding.Suitable surfaces listed by the manufacturer include stone, concrete, brick, metals, vinyl siding, glass, fibreglass, timber, and fully cured varnished or oil-based painted surfaces. The manufacturer says it may damage some plastics and advises against using it on plastics, so keep it away from them.How to use itShake the bottle well. Start by putting a little product on a cloth and rubbing the mark. If that does not work, apply a light amount straight onto the surface. If you see no damage, you can use a natural fibre scrub brush to gently loosen the residue. Finish by blotting, rinsing or power washing the area clean. Always test on a small, hidden spot first. This matters most on auto finishes and vinyl.Important notesThe product may dull or damage some surfaces, so a test patch is essential. Repainted surfaces can dry with a visible gloss difference between the treated and untreated areas. Do not use on plastics. This product is not designed for adhesive bonding or sealing work, it is purely a remover for cleaning up residue.Specifications Brand Tricleanium Product Adhesive Remover Size 500ml Colour Dark yellow liquid Base Solvent-based Application Bottle, applied with a cloth or directly onto the surface Flash point Approx. 36°C Specific gravity Approx. 0.85 to 0.89 at 20°C Country of origin Australia Use Household, trade and maintenance, indoors and outdoors SafetyIt may also cause an allergic skin reaction, as well as drowsiness or dizziness. Keep away from heat, sparks and open flames, keep the container tightly closed, and use only outdoors or in a well-ventilated area. Avoid breathing mist or vapour, wear suitable gloves and eye protection, and wash exposed skin after handling. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$33.82
Goof Off Professional Strength Remover is a fast-acting solvent remover for sticky, gummy and stubborn mess, supplied here in a handy 177ml can for the garage, workshop or toolbox. It is built to break down stuck-on adhesive residue and marks that ordinary household cleaners struggle to shift, so you can rescue tools, hard surfaces and finished work instead of replacing them.About the formulaA ready-to-use, thin, clear liquid based on a strong solvent blend that includes acetone and xylene. It is poured or wiped on with a cloth rather than sprayed, which gives you control when you are working on small marks or tight spots. Expect a strong solvent smell, so good ventilation matters.Where to use itIndoors: tackling sticker and label residue, tape and glue marks, crayon, pen and marker, chewing gum, candle wax, lipstick and scuff marks on sturdy hard surfaces around the home.Outdoors and in the garage: cleaning up adhesive, tar, asphalt and similar grime from hand tools, and removing dried latex paint drips and caulk smears from suitable hard surfaces.Suitable materials include metal, glass, brick, wood, concrete, grout, fibreglass, hand tools and most automotive surfaces, as well as fully cured varnished or oil-painted surfaces. It is also promoted for marks on carpet and clothing, but test those first.How to use itWear eye protection and gloves and work in a well-ventilated area, away from any ignition source. Test on a hidden spot first, because every surface reacts differently. Apply a small amount to a clean cloth, then blot or lightly rub the mess until it lifts. Thick or layered residue may need a second pass. Wipe the area clean, let the vapours disperse, and reseal the can straight away.Important notesDo not use on plastics, worn vinyl flooring, some automotive paints or some carpets, as solvents can soften, dull or discolour them. Avoid large areas and spot test dyed fabrics and carpet before treating a visible mark. Keep out of reach of children. Always follow the directions on the can.Specifications Brand Goof Off Product Professional Strength Remover (Adhesive Remover) Size 177ml can Form Ready-to-use liquid Colour Clear Base Solvent-based Application Applied with a cloth, blot or rub lightly Use Indoor and outdoor hard surfaces Pack dimensions 55 x 32 x 135 mm SafetyKeep away from heat, sparks, open flames and hot surfaces, and do not smoke. Use only with plenty of fresh air, wear safety glasses and chemical-resistant gloves, and stop work and move to fresh air if you feel dizzy or get a headache. If it contacts skin, remove contaminated clothing and rinse the skin with water. In case of fire use carbon dioxide, dry chemical, foam or water fog. Refer to the Safety Data Sheet (SDS) for full details.
$17.37
Rust-Oleum Concrete Fast Patch is a grey, two-part epoxy putty for repairing cracks, pits, spalls and low spots in concrete, supplied here as a 0.95L kit. It is made for quick garage, basement and slab repairs, and you do not have to wait for it to fully cure before it is prepared for coating in many situations.About the formulaA polyamine-cured epoxy putty that is 100% solids by weight and volume. The two parts mix 1:1, with no induction period, and the mixed putty stays workable for up to 30 minutes. It is designed to bond permanently to concrete without shrinking or cracking, and it can be used on vertical cracks as well as horizontal slab damage. No special equipment is needed.Where to use itIndoors: garage floors, basement floors and walls, and other concrete surfaces needing hairline crack, pit and small flaw repairs before painting or coating.Outdoors: the manufacturer data does not specifically rate it for exterior exposure, so check with the manufacturer before using it on exposed outdoor slabs.Suitable materials include concrete and masonry, and the manufacturer also lists wood, fibreglass and asphalt as substrates it bonds well to.How to use itRemove all dust, debris, paint, dirt, oil, loose concrete and curing compounds from the repair area, and make sure the surface is dry. Apply only when the temperature is between 10 and 38°C. Mix equal parts A and B on a scrap piece of cardboard or similar platform, using a broken paint stick or putty knife, until the colour is uniform. Press the putty into the crack, hole or pit with a small putty knife or plastic squeegee, then scrape off the excess so the repair is level. Most coatings can go straight over uncured patch where repairs are shallow and narrow. For large repairs (deeper and wider than about 12 mm), let the patch cure fully, then sand with 80 grit sandpaper to profile the surface before coating. Clean tools with xylene.Important notesThe kit fills cracks up to 6.4 mm deep. At 21 to 27°C and 50% relative humidity, full cure takes 8 to 12 hours, and the repair is then suitable for foot and vehicle traffic. Cooler or more humid conditions will change these times. If you are scraping or sanding old paint, it may contain lead, so wear appropriate respiratory protection and clean up carefully. Shelf life is 12 months in a dry, unopened pack. Do not use below 10°C.Specifications Brand Rust-Oleum Product Concrete Fast Patch Pack 0.95L two-part kit Colour Grey Base Polyamine-cured epoxy, 100% solids Mix ratio 1:1 (part A to part B) Application Putty knife or plastic squeegee Working time Up to 30 minutes Maximum crack fill Up to 6.4 mm deep Application temperature 10 to 38°C Full cure 8 to 12 hours at 21 to 27°C, 50% RH Shelf life 12 months, unopened Clean up Xylene Use Concrete, masonry, wood, fibreglass and asphalt SafetyKeep out of reach of children and animals. Store between 10 and 32°C, away from extreme heat, cold, moisture, direct sunlight and fire hazards. Two-part epoxy products can irritate skin and eyes and may cause allergic skin reactions, so wear gloves and eye protection, work in a well-ventilated area and wash thoroughly after handling. Xylene used for tool clean up is flammable and harmful, so handle it with care. Always read the manufacturer Safety Data Sheet before use.
$111.23
Scandia Wood Heater Fittings Gasket Adhesive & Sealant is a high-temperature paste made for fixing fibreglass rope seals and gaskets on wood heaters, stoves and fireplaces, supplied in a handy 75g tube. It helps rope seals stay put around door edges and flue joins while you work, then holds them in place once it has dried. This makes it a practical choice for replacing worn seals during heater maintenance.About the formulaA thick, cream to white paste with a firm body that stays where you put it, even on vertical surfaces. The manufacturer rates it for temperatures up to 1100°C, which suits the heat inside a solid fuel appliance. The tube comes with a nozzle that you can cut to suit the width of the seal or gasket you are fitting, so you can lay down a neat, controlled line of adhesive.Where to use itIndoors: fibreglass rope seals on heater and stove doors, flue joins, and other gaskets or glass seals on wood-burning heaters, stoves and fireplaces.Outdoors: the brand also lists wood-burning BBQs among its intended uses.Designed mainly for bonding fibreglass rope seals to the metal and masonry parts of a solid fuel appliance. If you plan to use it on another material, check suitability first with a small test.How to use itMake sure the surface is clean, dry and free of soot, loose debris, oil and old adhesive. Cut the tip of the nozzle to suit the seal you are fitting. Apply a line of paste to the channel or edge where the seal will sit, then press the rope seal or gasket firmly into place. Wipe away any excess before it dries.Important notesAllow the adhesive to dry overnight after application before lighting the appliance. Always follow your heater manufacturer's instructions for the correct seal size and fitting method. Always check the seal is fully seated and the door closes properly after fitting. Some users have found the paste firm to squeeze from the tube, so cutting the nozzle a little wider and applying steady pressure can help.Specifications Brand Scandia Product Wood Heater Fittings Gasket Adhesive & Sealant Size 75g tube Colour Cream to white paste Form Thick paste Application Squeeze tube with cut-to-size nozzle Temperature rating Up to 1100°C Drying time Overnight Use Wood heaters, stoves, fireplaces and wood-burning BBQs SafetyIt advises avoiding heat, flames and sparks during storage and handling, and providing good ventilation or respiratory protection against decomposition products. As a sensible precaution, wear gloves and eye protection, and wash off any skin contact with water. Store in a cool, dry place with the cap closed tightly. Refer to the Safety Data Sheet (SDS) for full details.
$9.32
Protite Fibreglass Resin is a low styrene emission (LSE) polyester resin for repairing cracks, dents, holes and worn patches on boats, caravans, cars, trailers, gutters and more, supplied here in a 500g size. Mixed with catalyst hardener and used with fibreglass matting or cloth, it gives DIYers and tradies a strong, workable repair material with good adhesion and a consistent wet-out.About the formulaA polyester LSE resin designed for general repair work. Once catalysed it cures to a hard, sandable and paintable finish that resists shrinkage and UV exposure. The resin is a viscous liquid and contains styrene, so it has a strong aromatic odour while you work. It does not cure on its own: you need to add a catalyst hardener (sold separately). Protite also offers a repair kit that bundles the resin with catalyst, matting and application accessories.Where to use itIndoors: repairs to fibreglass, timber, metal and plastic items, models and workshop projects, provided you have good ventilation.Outdoors: caravans, boats, trailers, bikes and cars, plus downpipes, leaky gutters, metal roofs and rusted panels, as well as fibreglass surfboards, pools and tanks.Suitable materials include fibreglass, steel, iron, aluminium, timber, masonry, PVC and smooth polyester surfaces. Test an inconspicuous area first when working on other plastics.How to use itClean the damaged area and remove loose material, grease and dust. Sand the surface so the resin has a key to grip. Pour only the amount of resin you can use in one session into a clean mixing container, then stir in the catalyst hardener. The catalyst manufacturer's guide is 2.5 to 3ml per 100ml of resin on a cold day, or 1.5 to 2ml per 100ml on a hot day. Mix thoroughly with a flat stirring stick until the colour is even. Work the resin into the repair (with matting or cloth if needed) by dabbing or rolling it out slowly to avoid trapping air bubbles. Allow it to cure, then sand and paint as required. Weather, humidity, depth of resin and draughts all change the amount of catalyst you need.Important notesUncatalysed resin will not harden, and too little catalyst or a very thin application can leave the resin tacky or uncured. Too much catalyst makes it gel sooner than expected. The manufacturer indicates the mix starts to gel after about 30 minutes at 25°C, and heat or extra catalyst shortens this while cold or less catalyst lengthens it. Take care when using polyester resin over epoxy surfaces and check compatibility first. Cure times depend on temperature and the amount of catalyst used. Clean tools before the resin cures.Specifications Brand Protite Product Fibreglass Resin (LSE) Size 500g Model number PF-FR0500 Base Polyester resin, low styrene emission Catalyst Required, sold separately Application Hand applied after mixing with catalyst, dabbed or rolled out Finish Sandable and paintable Resistance UV and shrink resistant Use Interior and exterior SafetyUse outdoors or in a well-ventilated area. Wear suitable gloves, eye protection and protective clothing, and avoid breathing vapours. Keep away from heat, sparks and open flames. Store in a cool, dry, well-ventilated place out of direct sunlight and away from ignition sources and incompatible materials, with the lid closed and out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$26.18
SikaBond-142 Instant Nails is a high strength, multipurpose construction adhesive for panels, timber, metal and masonry, supplied here as a convenient 3 pack of 300g cartridges. It has a thick, non-slump body that stays put on vertical surfaces, and it can be used as a one-way liquid adhesive or as a two-way contact adhesive depending on the job.About the formulaA one-component, ready-to-use adhesive based on synthetic rubber, supplied in a solvent-based form and finished in a beige colour. It dries fast, grips firmly and can be painted over once cured. Sika's data sheet lists a tensile strength above 1 MPa on a dry substrate (tested to AS 2329) and a peel adhesion above 40 N. Once set, it is rated for service temperatures from 0°C to +40°C.Where to use itIndoors: floor and wall panels, skirting and other trim, and timber or board products bonded to timber, metal or masonry backgrounds.Outdoors: Sika's data sheet does not confirm exterior use or weather exposure, so check the data sheet and test a small area first if the bond will be exposed to the elements.Suitable materials include timber, particleboard, MDF and plywood, aluminium, iron and steel, concrete, cement sheeting, fibreglass and masonry. It is also commonly used on plasterboard. Always test a small area first on any surface you are unsure about.How to use it Make sure surfaces are clean, dry and free of dust, grease and loose material. Cut the cartridge nozzle and load it into a caulking gun. For a one-way bond, apply the adhesive to one surface and press the parts together firmly. For a two-way contact bond, apply to both surfaces and join them as directed on the pack. The adhesive begins to skin over in roughly 1 to 5 minutes, so have your parts ready and work promptly. Apply it between +5°C and +40°C substrate temperature. One cartridge covers roughly 15 linear metres with a continuous 5mm bead. Important notesFull cure takes approximately 7 days, depending on weather conditions. It is not suitable for immersed applications. Keep unopened cartridges in their original sealed packaging in dry conditions between +5°C and +25°C. Shelf life is 18 months from the date of production.Specifications Brand Sika Product SikaBond-142 Instant Nails Construction Adhesive Pack 3 x 300g cartridges Colour Beige Base One-component synthetic rubber, solvent-based Application Cartridge, via caulking gun Skinning time 1 to 5 minutes Full cure About 7 days Coverage About 15 linear metres per cartridge (5mm bead) Density About 1.1 kg/L Tensile strength Over 1 MPa on a dry substrate (AS 2329) Service temperature 0°C to +40°C Shelf life 18 months from production SafetyIt is also hazardous to aquatic life, so keep it out of drains and waterways. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Use it only outdoors or in a well-ventilated area. Wear protective gloves, clothing and eye protection. Refer to the Safety Data Sheet (SDS) for full details.
$16.04
Fix-It-Fast Repair Tape is an aluminium-faced butyl flashing tape for quick, dependable waterproofing and leak repairs, supplied here as a wide 150mm x 5m roll. It suits DIYers and roofing or building trades who want a simple, self-adhesive way to seal flashings, gutters and damaged roof areas without mixing, heating or special tools.About the tapeThe tape pairs an aluminium top layer with a self-adhesive butyl backing protected by a release liner. This construction is designed for waterproofing and vapour sealing, and it is formulated to bond to virtually all non-porous building materials. The aluminium face is UV resistant, and the product is promoted for its excellent age resistance. The 150mm width covers larger repair areas in fewer passes than the narrower rolls in the range.Where to use itIndoors: vapour sealing and general waterproofing tasks on non-porous building materials where the tape will not be exposed to the weather.Outdoors: flashing repairs, gutters, downpipes, cracked or damaged roofing, metal roof sheeting, sheds, skylights, caravans and boats.Suitable materials include metal (including Colorbond), PVC, polycarbonate, fibreglass, timber and smooth masonry, provided the surface is clean, dry and free of dust and oils.How to use itClean the surface thoroughly and make sure it is dry. Cut the tape to the length you need and peel away the release liner. Press the tape down firmly, working from the centre outwards to push out air pockets, then press the edges down so they are fully sealed. For best results, apply when the temperature is above 5°C.Important notesAdhesion is best on clean, dry, non-porous surfaces. If an area is wet, dry it as much as you can before applying the tape. Rough, dusty, oily or porous surfaces can reduce adhesion, so prepare them properly first. The manufacturer indicates the tape remains stable in service from about -40°C to 90°C. Check the repaired area from time to time to make sure the seal is holding.Specifications Brand Fix-It-Fast Product Repair Tape, Aluminium Reinforced Butyl Flashing Tape Size 150mm wide x 5m long (1 roll) Colour Aluminium (silver) Construction Aluminium top layer with self-adhesive butyl backing Application Hand applied, peel and stick Service temperature -40°C to 90°C (manufacturer FAQ) Best application temperature Above 5°C Use Interior and exterior SafetyKeep it away from young children, and wear gloves when handling the aluminium edges if you are cutting it. Store the roll in a cool, dry place out of direct sun. Refer to the Safety Data Sheet (SDS) for full details.
$44.47
Crommelin Sprayable Exterior Grade Waterproofing is a rubberised, shake-and-spray waterproofing coating in a 400ml aerosol, made for outdoor areas that cop regular water and UV exposure. It is designed to seep into and seal leaks, cracks and small gaps, leaving a flexible, watertight film that suits quick repairs on roofs, gutters and similar exterior surfaces. This pack is the grey finish.About the formulaA rubberised coating delivered from a pressurised can, so there is no brush, roller or mixing involved. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), permanently flexible and fast drying. It also helps protect the coated surface from corrosion and stops moisture getting through. Once cured it can be overcoated with most water-based (acrylic) paints.Where to use itIndoors: not intended for interior use. This is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, hoses, air conditioner drip pans and ductwork.Suitable surfaces listed by the manufacturer include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particle board, PVC piping and fibreglass. The product has not been tested for use in potable water systems.How to use itSurfaces must be clean, sound and dry, and free of dust, grease, release agents, loose particles and other contaminants. Shake the can vigorously for one minute, and do a test spray on cardboard to get a feel for the spray pattern. Hold the can roughly 8 to 18cm from the surface and apply a thin first coat, which acts as a primer, then let it dry. Follow with a heavier coat, moving the nozzle a little closer to build a thicker film. For longer-lasting protection apply three to four coats, and for wider cracks and gaps keep adding coats until the cavity is filled. Apply to the positive side only (the side where water enters the substrate). Recoat once touch dry, which is about 20 to 30 minutes depending on thickness, weather and site conditions, and allow good airflow to help it cure.Important notesApply in temperatures of about 10 to 30 degrees C and avoid applying when humidity is high (the recommended maximum is 85% during application and cure). Avoid spraying in high wind or dusty conditions. Cold temperatures and poor airflow will lengthen cure times. It can be painted over after 24 hours. Full cure takes 48 hours, and the coating should not be exposed to water until then. Coverage depends on the shape and condition of the surface. Always do a small test area first.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 400ml aerosol can Colour Grey Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Recoat time About 20 to 30 minutes (touch dry) Paint over After 24 hours Full cure 48 hours Application temperature 10 to 30 degrees C Overcoating Most water-based (acrylic) paints Use Exterior SafetyKeep away from heat, sparks, flames and hot surfaces, do not spray onto a flame or ignition source, and do not pierce or burn the can, even when empty. Use in a well-ventilated area, avoid contact with skin, eyes and clothing, and wash hands before eating, drinking or smoking. Store out of direct sunlight and keep below 50 degrees C. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Crommelin Sprayable Exterior Grade Waterproofing is a ready-to-spray rubberised coating for sealing leaks and cracks on outdoor surfaces, supplied here as a 400ml aerosol can in white. It is made for spots that cop regular rain and sun, and it dries to a flexible, watertight layer that can be painted over with most acrylic paints.About the formulaA rubberised waterproofing coating in a pressurised can, so there is no brush, roller or mixing involved. The spray works its way into small holes and cracks to stop water getting through, helps block moisture penetration, and gives metal surfaces a barrier against corrosion. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), fast drying and permanently flexible. The white finish suits light-coloured roofing and masonry.Where to use itIndoors: not intended for interior use, as this is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, and hoses, air conditioner drip pans and ductwork.Suitable materials include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particleboard, PVC piping and fibreglass.How to use itMake sure the surface is clean, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and any other contaminants. Crommelin recommends its Water Rinsable Degreaser for removing grease and oils. Shake the can well, then spray the area to be sealed following the directions on the can. Once the coating has dried it can be over-painted with most acrylic paints. Full application instructions are available on the Crommelin website.Important notesThis product has not been tested for use in potable water systems, so do not use it on drinking water tanks or pipework. It is an exterior grade coating and is not designed as an under-tile or interior wet area membrane. Check the can and the manufacturer's data sheet for drying and recoating times and for surface or ambient temperature limits before starting.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 1 x 400ml aerosol can Colour White Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Overcoating Can be painted over with most acrylic paints Use Exterior Pack dimensions Approx. 64 x 64 x 197 mm SafetyThe can may burst if heated. Use only in well-ventilated areas, avoid breathing the spray, and keep away from heat, sparks, flames and other ignition sources. Wear gloves and eye protection, and remove any contaminated clothing and splashes from skin straight away. Store in a cool, dry place out of direct sunlight, do not expose to temperatures above 50°C, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
![Selleys Plasti-Bond Heavy Duty Bog Two Part Polyester Filler 400g [Off White]](http://gluesaustralia.com.au/cdn/shop/files/Plasti-BondHeavyDutyBog400g_b2b227b8-96d0-4b9a-9dfa-7d64e62b31f5.png?v=1785218520&width=645)
Selleys Plasti-Bond Heavy Duty is a two part polyester filler built for repairs that have to carry load, not simply look tidy. Once the hardener is stirred through, it firms up to a dense, rigid mass in about twenty minutes without the shrinking or cracking that catches out lightweight patching compounds, and it holds its shape well enough to be drilled, tapped and fixed into after curing. The 400g can covers the middle ground jobs that a small pack runs short on. What it is The pack contains an off white polyester putty base and a separate hardener that is mixed in immediately before use. Working time is short, around five minutes at normal room temperature, so the product is mixed in batches rather than all at once. Cured Plasti-Bond can be sawn, drilled, filed, sanded and painted, and the base can be tinted with cement oxides or paint tinters before the hardener goes in if a coloured finish is wanted. Where to use it Indoors: filling holes, cracks and splits in walls, ceilings, floors and doors; rebuilding worn areas around hinges, locks and door handles; making good chipped tiles and ceramics; anchoring bolts and fixtures into masonry; stopping countersunk fastener heads flush in almost any material. Outdoors: patching chipped concrete steps and paths, repairing galvanised guttering and downpipes, and restoring fibreglass, timber and metal on furniture, sporting gear, cars, caravans and boats above the water line. Outdoor repairs should be painted, since the cured filler can discolour if left bare in sunlight. How to use it Prepare the surface so it is clean, dry, unpainted and free of grease or oil. On steel or aluminium panel work that will see vibration, punch or drill the area first to give the filler a positive key. Stir the base thoroughly, then blend in the hardener, working the mix from side to side until the colour is completely uniform. Extra hardener speeds the set in cold weather; less hardener buys time across several separate fills. Apply with a putty knife or spatula, pressing firmly into the repair and slightly overfilling to leave material for sanding. Feather the edges as you go. Take off most of the excess with a Surform or file between roughly twenty and thirty minutes, while it is firm but not yet rock hard. Once fully hard, finish with ordinary files or sandpaper. Paint with water based or oil based paint. Clean tools with mineral turps before the product cures. Important notes Not suitable for continuous immersion or for joints that need to stay flexible. May not adhere to polyethylene, polypropylene or PTFE. Can discolour if left unpainted outdoors. Mix only what you can apply inside the working time; cured material cannot be re-softened. Replace the lid firmly after use and store the can in a cool place. Specifications Brand Selleys Product Plasti-Bond Heavy Duty Bog Pack size 400g Technology Two part polyester putty Appearance Off white paste Working time Approximately 5 minutes at 23 degrees C Cure time Approximately 20 minutes Suitable substrates Metal, timber, brick, fibre cement, fibreglass, concrete, plaster, tiles, ceramics and many plastics Paintable Yes, once cured Clean up Mineral turps before curing Use Indoor and outdoor Safety Polyester fillers and their hardeners are flammable and give off solvent vapour while curing. Work in a well ventilated area, keep the product away from sparks, flames and other heat sources, and wear gloves and eye protection when mixing and applying. Avoid prolonged skin contact and wash any splashes off promptly. Keep out of reach of children, do not allow washings to enter drains or waterways, and dispose of unused material and empty containers in line with local regulations. Consult the current Selleys Safety Data Sheets for the base and the hardener before use.
$42.70
Loctite EA 9235 (Five Minute E-Pox-E, item EFQ5) is a fast-acting two-part epoxy that mixes resin and hardener in equal parts to form a tough, rigid, high-strength bond in about five minutes. Supplied in a dual-barrel syringe that dispenses both components in the correct 1:1 ratio every time, it is ideal for fast permanent repairs and multi-piece projects across a wide range of household, workshop and trade materials. Once cured it resists water and most common solvents, and can be sanded, drilled and machined. It can also be used as a versatile filler for gap filling, surface repairs and laminating. Bonds: metal, glass, ceramic, china, tile, stone, concrete, wood, fibreglass and most rigid plastics. Where to use it Indoor: repairing ceramics, china and glassware, fixing tools and toys, bonding tiles, and general household and hobby repairs. Outdoor: bonding stone, concrete and masonry, plus garden and workshop repairs. Not recommended for continuously wet areas or prolonged water immersion. How to use 1. Make sure surfaces are clean, dry and free of oil, wax, paint and rust. Roughen smooth surfaces by sanding for a stronger grip. 2. Remove the plug and cut the syringe tip at the marked opening. Stand the syringe upright and press the plunger gently to expel any air. 3. Depress the double plunger to dispense equal parts of resin and hardener onto a disposable surface, then mix thoroughly for about one minute. 4. Apply to both surfaces within one to two minutes of mixing and press together. Support the join for around 10 minutes. 5. Usable strength is reached in about 1 hour and the bond fully cures in 24 hours. Wipe the tips clean and replace the plug for storage. Clean uncured adhesive with acetone before it sets. Cured adhesive can be carefully cut away with a sharp blade. Important notes Not recommended for polyethylene, polypropylene, nylon, non-stick coatings or flexible materials. Not suitable for potable (drinking) water systems, prolonged water immersion, or short-term heat above 150°C. Apply between 4°C and 35°C. Specifications Part number Loctite EA 9235 / EFQ5 Size 25ml dual syringe Chemistry Two-part epoxy (epoxy resin / polymercaptan hardener) Mix ratio 1:1 by volume Set time Approx. 5 minutes Usable strength Approx. 1 hour Full cure 24 hours Cured colour Clear amber Hardness 80 Shore D Service temperature -23°C to 49°C continuous (up to 150°C intermittent) Water resistant Yes Sandable / machinable Yes Paintable No Shelf life 24 months unopened SafetyContains epoxy resin and polymercaptan/amine hardeners. Causes skin and eye irritation and may cause an allergic skin or respiratory reaction. Wear gloves, work in a well-ventilated area and avoid breathing vapours. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$33.75
Strengthen joints, seams, and repairs with this tough fibreglass mesh tape. It helps prevent hairline cracks, improves bond strength, and delivers a smooth base for top coats on plasterboard and cement sheet surfaces. Why you will like it Reinforces joints to reduce cracking around seams and patches Open mesh allows compound to key through for a strong bond Clean edges for easy alignment along butt and tapered joins 50mm width suits standard plasterboard seams and corner work 20m roll is great for rooms, small renos, and ongoing touch ups Great for Plasterboard joins and butt joints Repairs around door and window openings Ceiling crack reinforcement Patching holes and dents before finishing Use with base coat and top coat compounds How to use Ensure the surface is clean, dry, and free of dust. Lay the tape centered over the joint or crack, pressing to seat it flat. Apply a generous first coat of compound through the mesh and let it dry. Feather additional coats wider than the last until flush with the surface. Sand lightly once dry, then prime and paint. Specifications Brand: Builders Edge Type: Fibreglass joint reinforcement tape Width: 50 mm Length: 20 m Material: Fibreglass mesh Colour: White Tips For best results, keep the tape flat with no bubbles before coating. Use a wider knife on each subsequent coat to blend the repair. Allow full dry time between coats to avoid shrinkage lines. Glues Australia helps Australians fix, build, and finish with confidence.
$13.21 $9.32
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more. About the product Works as a sealer, bonding agent, or primer Completely non-toxic Dries to a clear, flexible bond Works on porous and non-porous surfaces UL approved Will not dissolve hard foam Safe for Styrofoam Works well with Plastics and expanded polystyrene Frequently Asked Questions Can I keep my weldbond bottle outside in the garage? Will it freeze? Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use. What is the shelf life of weldbond? Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use. Is weldbond non-toxic? Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236. Is weldbond tested on animals or created with any animal by-products? Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
$24.43
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes. Works best on: • Porous materials • Ceramic • Metal • Pottery • Wood • Tile • Crafts Properties: Initial colour: Green resin/white hazy hardener Maximum Gap: .25” Final colour: White hazy Hardness, Shore D: 75-85 (After full cure) Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%) Handling Time: After 1 hour Aluminum: 900 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C) Instructions: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours. Helpful Hints: To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
$9.95
The Permanent Patch is a very unique, easy-to-use UV or sunlight activated repair patch. It is fiberglass-reinforced polyester and creates long-lasting repairs. No mixing is required - one step no mess. This incredible permanent patch is waterproof and will not rot or rust. It can be drilled, tapped, sanded and painted in less than an hour. The Permanent Patch makes long lasting repairs on Everything Under The Sun™. Works best on Aluminum Concrete Drywall Fiberglass Metal Most Plastics Pottery PVC Pipe Rubber Stucco Wood USE INSTRUCTIONS: NOTE - This product must be exposed to UV sunlight or UV source to cure. Rubber or plastic gloves recommended for sensitive individuals. Not recommended for drinking water applications. 1. Use the Anchor-Tite Patch in a well-ventilated area. Keep the Patch in the black, UV-protected package until you are ready to do a repair. 2. Clean parts to be repaired with soap & water and allow to dry completely. Roughen surface with wire brush or sandpaper. 3. While still in the black UV-protected package, cut the patch material to extend ¾” beyond the repair area using scissors or knife. Remove the white backing and apply cut Patch over repair and press firmly in place. Store unused portion away from sunlight or UV sources. If outside surface is to be painted or finished, remove clear nylon film prior to cure. 4. Expose the bonded Patch to UV sunlight, black lamp or other UV sources until the product is hardened (see approximate times above). 5. After the product is hard and fully cured, it can be drilled, sanded or painted. 6. Wash hands and skin well with soap and water after use. STORAGE AND SHELF LIFE Store product sealed in the original black UV-protected package in a cool (<75F), dry location away from UV sources or sunlight. Stored under these conditions, a one-year shelf life can be expected. SafetyAND HANDLING PRECAUTIONS Contains Styrene. Eye, skin & respiratory irritant. Use & store in a well-ventilated area away from heat & sunlight. Avoid contact with eyes & skin. Refer to the Safety Data Sheet (SDS) for full details.
$35.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40o F to +176oF (-40oC to +80oC) Instructions: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours. Storage: After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected. SafetyContains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. Refer to the Safety Data Sheet (SDS) for full details.
$29.95
Instant Setting Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 90 seconds Pacer Technology Super Glue 90 Second Instant Epoxy Adhesive (SY-IN, 15353) works best on: • All Purpose • Ceramic • Glass • Wood • Leather • Fiberglass • Metals • Most Plastics Properties: Initial color: Clear to amber Mix Ratio (parts by volume): 1:1 Final color: Light yellow Maximum Gap: .25” Set Time: 90 Seconds @ 65-80F Hardness, Shore D: 75-85 (After full cure) Handling Time: After 10 minutes Shear Strength, Steel: 2000 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 1400F (-400 to 600C) Use: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions and mix thoroughly until color is uniform. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 90 seconds at room temperature (77F or 25C) with full cure in 24 hours. STORAGE AND SHELF LIFE After use, wipe tips to remove residual product and reseal container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected.
$25.00
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes. Pacer Technology Super Glue Quick Setting Epoxy (SY-QS, SYQS8, T-QS, 15250, 15350) works best on: All-Purpose Ceramic Metal Pottery Wood Tile Crafts Fabric Properties: Initial colour: Clear hazy to light yellow Final colour: Light yellow Set Time: 4-6 minutes @ 65-80F Handling Time: After 30 minutes Full Strength: 24 hours Maximum Gap:25" Hardness, Shore D: 75-83 (After full cure) Shear Strength, Steel: 1200 psi ( 20%) Operating Temperature Range: -40oF to +176oF (-40oC to +80oC) Use: 1. Surfaces should be clean and dry, free of oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from containers following package directions and mix thoroughly approximately 1 minute. 4. Apply mixed epoxy to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours.
$19.95
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance. Incredible bond strength Waterproof Superior strength Adheres to even visibly damp surfaces Fast curing - less than 30 minutes Materials: wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
$25.98
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance. Incredible bond strength Waterproof Adheres to even visibly damp surfaces Fast curing - less than 30 minutes
$10.50
![Sikaflex Sika 227 Automotive Sealant Fast Curing non-sagging 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003562_9dff8874-70fe-48dd-b768-e32af265ef3b.jpg?v=1754711664&width=645)
Sikaflex-227 is a one-component polyurethane sealant designed for car body construction, curing on exposure to atmospheric moisture to form a durable elastomer. USESikaflex-227 is suitable for sealing, seam sealing, simple bonding as well as for vibration reduction and sound deadening measures in crash body repair and car body construction. Suitable substrate materials are metal primers and paint coatings (two-part systems), metals, painted plastics and plastics. CHARACTERISTICS AND ADVANTAGESOEM approved qualityFast over-paintableResistant to ageingLow odourCan be sandedBonds well to a wide variety of substratesShort cut-off stringOverhead work possibleFast curingSilicone free Product Benefits- Adheres to a wide range of substrates, without primer in many cases- Exhibits tenacious adhesion to aluminium, FRP, steel, wood, SMC, RIM, prepainted metals, ZINCALUME, Zincgrip, and aluminized steel, without attacking the metal coating- Fast tack free time- Cures rapidly to an elastic consistency with excellent cut and tear resistance- Low odour, non-staining- Paintable- Weather resistant- Resistant to road salts Areas of Application- Sealing exterior lap seams in many applications, including truck trailers, RV's, metal roofs, window perimeters, grain bins and HVAC units- Sealing rivet seams- Sealing of exposed and concealed joints of aluminium, steel, coated metals, wood, roof rails, and door hinges in transport equipment- Sealing and caulking expansion joints- May be suitable for use on a wide variety of substrates; including aluminium, steel, glass, wood, metal primers and paint coating (2-c systems), metals, painted plastics and many different types of plastic. Cure MechanismSikaflex®-227 cures by reaction with atmospheric moisture. At low temperatures, the water content of the air is generally lower and the curing reaction proceeds somewhat slower Chemical ResistanceSikaflex®-227 is resistant to fresh water, aqueous cleaning solutions; temporarily resistant to fuels, mineral oils, vegetable and animal fats and oils; not resistant to organic and mineral acids, alcohol, and caustic solutions or solvents. The above information is offered for general guidance only. Method of ApplicationSurface preparationSurfaces must be clean, dry and free from all traces of grease, oil and dust. As a rule, the substrates must be prepared in accordance with the instructions given in the current Sika Pre-Treatment Chart. ApplicationCartridges: Cut tip to joint size.Puncture airtight seal. Install with hand or power operated gun.Unipacks: Place unipack in the application gun and snip off the closure clip. Cut off the tip of the nozzle to suit joint width and gun the sealant into the joint with a suitable compressed air or hand operated gun, taking care to avoid air entrapment. Once opened, packs should be used up within a relatively short space of time. Do not apply at temperatures below 40°F (5°C) or above 100°F (38°C). The optimum temperature for substrate and sealant is between 60°F (15°C) and 77°F (25°C). For advice on selecting and setting up a suitable pump system, please contact the System Engineering Department. Tooling and finishingTooling and finishing must be carried out within the tack-free time of the sealant. Finishing agents or lubricants must be tested for suitability/ compatibility. RemovalUncured Sikaflex®-227 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Strictly follow the solvent manufacturer's instructions for use and warnings.Hands and exposed skin should be washed immediately using a suitable industrial hand cleaner and water. Do not use solvents on the skin! OverpaintingSikaflex®-227 can be overpainted when tack-free. The paint and paint process must be tested for compatibility by carrying out preliminary trials. Sikaflex®-227 should not be exposed to baking temperatures until it has attained a full cure. It should be understood that the hardness and film thickness of the paint may impair the elasticity of the sealant and lead to cracking of the paint film with time.
$27.48
SikaBond® SprayFix: The Ultimate Aerosol Spray Adhesive for Multipurpose Use High-Performance, Fast-Drying, & Repositionable Adhesive SikaBond® SprayFix is your go-to aerosol spray adhesive for both temporary and permanent bonding. With its high performance, low odour, and fast-drying time, it's designed for your convenience. Key Advantages: Easy to use Low odour Dries clear Fast drying time (approximately 2-4 minutes) High initial strength Contains no chlorinated solvents - suitable for indoor use Repositionable for 1-2 minutes Applications Include: Upholstery Floor Repairs Furniture Lamination Art and Crafts (e.g., mounting prints) Suitable Substrates: Felts and Fabrics Metals Foams Cork Most Plastics Rubber Gaskets Fibreglass Wood (e.g., plywood, particle board) How to Use: Ensure the surface is clean, dry, and free of dust and grease. Shake the can well before use. Hold the can approximately 80-100 mm from the surface and spray lightly. Allow a few minutes for drying. Packaging: Available in 150g and 350g aerosol cans. Color: White when applied, clear when dry. Cleaning of Equipment: After use, invert the can and press the tip until clear propellant comes out for cleaning. Uncured overspray can be removed with Sika® Colma Cleaner or another suitable solvent.
$34.00
![Sika Sikaflex 252 High Strength structural Adhesive Sealant [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895456164_5c293f0a-df90-415e-875b-0ed963018cfa.jpg?v=1754711706&width=645)
High strength, structural grade polyurethane adhesive sealant High strength elastic adhesive, suitable for structural joints subjected to high dynamic stress Suitable for use on trucks, trailers and caravans with excellent adhesion to timber, metals, primers and paint coatings Vibration dampening USE Sikaflex® 252 is suitable for structural joints that will be subjected to dynamic stresses. Suitable substrate materials are timber, metals, particularly aluminium (incl. anodized components), sheet steel (incl. phosphated, chromated and zinc-plated components), metal primers and paint coatings (2-c systems), ceramic materials and plastics. CHARACTERISTICS AND ADVANTAGES 1-C formulation Elastic Can be overpainted Good gap-filling properties Capable of withstanding high dynamic stresses Vibration Damping Non-corrosive Electrically non-conductive Bonds well to a wide variety of substrates
$53.62
Selleys Urethane Bond Is a high strength shock proof, water and chemical resistant polyurethane adhesive. Features High strength Achieves maximum bond in 48 hours Shockproof Flexible, shatterproof and impact resistant so it can take knocks Durable Lasts a long time Chemical resistant Wont break down by temporary exposure to most chemicals i.e. solvents Waterproof and weatherproof Good for bonds exposed to the elements When curing, Urethane Bond expands, filling voids and strengthening the bond Easy to use Requires no mixing, ready to use straight from the pack Only need to apply adhesive to one surface Versatile Can be used inside or outside Sandable and paintable after dries
$25.00
![Selleys Storm Sealant [Black] Waterproof Any Material Wet or Dry Sil-X 290ml](http://gluesaustralia.com.au/cdn/shop/files/e477ca37aa8d409fa7f84e307b56d97a.jpg?v=1757752932&width=645)
Selleys STORM Sealant delivers a waterproof seal on any material* wet or dry, indoor or outdoor. It can even be applied in the rain to stop leaks in an instant. Features Can be applied to wet or dry surfaces* Good adhesion on any surface* even when applied in the rain Excellent UV and weather resistance Suitable for interior and exterior use Long lasting flexibility Easily paintable with water-based paints Low VOC – so can be used in any environment without discomfort Made with Sil-X, an advanced polymer technology which delivers superior performance in demanding situations where conventional products fail, on any surface* wet or dry. Where can this product be used? Perfect for use on and around: Skylights Gutters Downpipes Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic Tiles Fibreglass All construction substrates Most plastics* How to use this product Ensure substrates are clean and free of oil, grease or loose particles. Cut cartridge tip, fit to the nozzle and cut to size (5mm), then place in the caulking gun. Apply with the caulking gun, pushing sealant into joint or gaps. Smooth off using a spatula dipped in turps, within 5 minutes of applying. If painting, paint with two coats of a quality water-based exterior paint. Storage and re-use Store in cool, dry conditions below 30°C. Use within 6 months of opening. Clean up Clean up with turps before Storm cures. The cured sealant can be removed by scraping or sanding or with the help of Selleys Silicone Remover. Handy Hints For neater joints, mask sides before applying sealant and remove the tape before sealant skins. Paint with water-based paint. If the paint does not wet out sealant surface properly, lightly sand sealant before painting. Limitations Not suitable for PE, PP, PTFE, permanent water immersion or plugging leaks subject to pressure. Safetytips Cure excess product before disposal. Avoid skin and eye contact and inhalation of vapour. If skin contact occurs, wipe off immediately and wash with running water. Ensure use in a well-ventilated area. Refer to the Safety Data Sheet (SDS) for full details.
$19.00
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$19.12
Power Grip™ sticks and withstands virtually anything*. Powered by SIL-X® technology for high versatility and durability, this glue will work even in the most extreme conditions*. Where normal glues fail, Power Grip™ rises to the challenge. Features Sticks and withstands virtually anything* Outperforms Super glue on uneven, porous or non-rigid surfaces. Shockproof – bends on impact High flexibility High bond strength Gap filling: Sticks uneven surfaces together, which means you can fix things that didn’t break cleanly. Water & Weatherproof Temperature Resistant 15C – 120C Dishwasher Safe Works on uneven surfaces Set time 3 minutes Colour Dries clear What materials is this product suitable for? Metal Wood Stone Bricks Concrete Masonry Ceramic Glass Foam Leather Laminate Vinyl Fabric Cardboard Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) How to use this product Use in a well-ventilated area Ensure surfaces are clean and dry. Remove cap and apply to a surface. Simply apply and hold the bond in place for at least 1 minute or until set (around 3 mins, allow longer for non-porous surfaces such as metal and plastics). If necessary clamp or tape to support until adhesive sets – for porous surfaces such as wood and ceramics, practical strength is usually achieved within 12 hours. Product cures rapidly, wipe nozzle clean and tightly replace cap immediately. Store upright in a cool dry place. Clean up before adhesive sets with turps or acetone. Handy tips Initial bond in 3 minutes, full cure in 12-24 hours. To reduce set times on non-porous surfaces, keep surfaces apart for 30 seconds before bringing together. Safety Tips Causes skin irritation. May cause an allergic skin reaction. Causes serious eye damage. KEEP OUT OF REACH OF CHILDREN. Avoid skin and eye contact and breathing vapours. Use in a well-ventilated area. Wash thoroughly after handling. Product releases methanol during cure. Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place. *Not suitable for polyethylene, polypropylene or PTFE. Not for permanent water immersion. Avoid UV exposure
$9.00
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material. Features Will not sag, run or drip. Easy to use – no mess. Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing. Good adhesive strength. Can be used to reshape, rebuild and repair a multitude of surfaces and applications. Good gap filling properties. Long-lasting, durable solution. Heat resistant to 120°C continuously or 140°C intermittently. Can be used under fresh or salt water. Longer set time (less than 20 min). Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649. Higher tack for underwater repairs. Where can this product be used? Creating water features/ attaching pebbles under water in a pond Sealing holes in foundations and outer walls Repairing generators, water and fuel pumps Re-setting ceramic tiles in swimming pools etc For fast and permanent repairs to damp and wet substrates, and even for underwater repairs Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets Forming custom gaskets etc Ideal for emergency in-water repairs Repairing fishtanks, ponds, pools Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible. Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber Set time increases at temperatures below 20°C Not recommended for use where hydrostatic pressure is present prior to cure What materials is this product suitable for? Fibreglass Wood/Timber Ceramics Metal Concrete Glass Most plastics (pre-test required) Masonry How to use this product Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning. Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature. Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place. For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins. Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured. After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures. After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted. Wash hands thoroughly with soap and water after use. Handy tips Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it. To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done. For best results, use Knead-It Multi-Purpose for applications in contact with drinking water. Use Knead-It Steel for applications on metal or fuel contact Store in a cool place for maximum shelf life For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safetytips Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Replace siliver disc to seal ends and keep in a cool dry place.
$13.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7ce782d52b264c1db0e928662698e299.jpg?v=1757753227&width=645)
$16.00
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/51345fd2ddf64a74a03e2c6b9e0d7e1a.jpg?v=1757753232&width=645)
$17.26
![Selleys Flexiseal Multipurpose Sealant Polyurethane 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/81e21d7d520d41a280976d39a403b5c9.jpg?v=1757753238&width=645)
$16.00
Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces. Where can this product be used? Boat repairs including hull repairs Surfboard / Surfski repairs Automotive repairs Repairing a leaky gutter Patching downpipes Patching metal roofs or grass catchers Not approved for contact with drinking water What materials is this product suitable for? Fibreglass Plywood Metal Fibro Sheeting Most Plastics How to use this product Wear rubber or plastic gloves when handling fibreglass Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge. For wide holes, glue a piece of cardboard to the back of the hole to form a base. Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly. Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels. Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required. Finishing When the patch has completely hardened, (approximately 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required. Clean up product with Solvent Acetone before it cures Handy tips At higher temperatures, the working time decreases. Can only be tinted with iron oxide or other dry pigments .which must be mixed in very thoroughly. Surfaces to be joined should be clean and dry. If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result. A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). In large amounts, heat can be generated during cure. Care should be taken on heat-sensitive surfaces with large amounts. Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Features Non-corrosive Weather resistant – resistant to water, weather or marine growth Rapid setting Impact resistant – can take knocks Sandable – can be sanded after 1-2 hours Can be painted over Extended working time – up to 20 minutes at 20°C Dries Opaque Heat resistant to 100°C
$41.01
![Selleys Marine Flex For Boats Pools and Spas Water Proof [Black]](http://gluesaustralia.com.au/cdn/shop/files/f795ca009d10470fb346ebed4b3dc2a3.png?v=1757753303&width=645)
Selleys Marine Flex is a high-performance adhesive and sealant designed for marine and water-exposed applications. Using Sil-X advanced polymer technology, it provides a permanent watertight seal above and below the waterline, even in salt, fresh, or chlorinated water. Key Features Cures and bonds underwater No primer required for most surfaces Strong and flexible bond absorbs vibration and movement Solvent-free and isocyanate-free formulation Sandable once cured 10-year watertight seal guarantee (above waterline) Where to Use Ideal for marine, pool, spa, and construction projects where water exposure or movement is expected. Suitable for bonding and sealing: Boat hulls, fittings, and deck seams Pool tiles, coping, and skimmer boxes Concrete, fibreglass, sealed timber, and metal surfaces Glass, ceramics, and most rigid plastics Technical Details Technology Sil-X advanced polymer Colour White or Black Size 410g cartridge Finish Smooth, paintable once cured How to Apply Ensure surfaces are clean and free from grease, oil, or dust. Can be applied to damp or wet surfaces. Cut the nozzle to the desired bead size and apply using a standard caulking gun. Tool the sealant immediately with a soapy water solution before it begins to skin. Allow to cure fully before sanding or painting if required. Limitations Not suitable for polyethylene (PE), polypropylene (PP), or PTFE materials Gelcoat surfaces should be lightly sanded before application The watertight guarantee applies to applications above the waterline Why Choose Selleys Marine Flex When you need a sealant that can withstand constant water exposure, movement, and vibration, Selleys Marine Flex delivers unmatched reliability. It bonds powerfully, stays flexible, and ensures a lasting waterproof finish for marine, pool, or construction applications.
$28.00
You have seen 96 out of 141 products
Adhesives and repair systems for fiberglass panels and parts. Epoxies and structural adhesives are common; key surfaces and clean thoroughly for best adhesion. Match flexibility, temperature and chemical resistance to marine, automotive or outdoor environments. Consider gel formats for vertical application. Use the filters to narrow by chemistry, cure speed, temperature rating and clean-up. Always check the product page and TDS/SDS for suitability and instructions.
