![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$24.00
Selleys 3 in 1 adhesive, sealant and gap filler is an extremely versatile product – It is perfect for virtually any sealing, bonding and filling applications on virtually any surface. Selleys 3 in 1 is a high strength construction adhesive, a waterproof sealant and no-shrink gap filler – all in one. Ideal for sealing, bonding and filling almost any material, damp or dry, inside or outside, providing durable waterproof seals, strong bonds and a perfect paintable finish. Excellent adhesion to almost any surface, including glass, metals, timber, brick, concrete, tiles and most plastics* Features As a Construction Adhesive High strength bond Water and weather resistant Use on multiple surfaces As a Sealant Provides a lasting waterproof seal Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints As Gap Filler Highly durable – no shrinkage, long-lasting resistance to cracking and crumbling, water-resistant Can be used on all indoor and outdoor surfaces Easily paintable with 2 coats of water-based paints *Not for polyethylene, polypropylene or Teflon Where can this product be used? Use 3 in 1 for sealing, bonding and filling almost any material Damp or dry, inside or outside Provides a durable waterproof seal Provides strong bonds and a perfect paintable finish What materials is this product suitable for? Glass Metals Timber Brick Concrete Tiles Most plastics (not for polyethylene, polypropylene or teflon) How to Use Adhesive Apply to one surface, in beads for broad surfaces (every 30cm) or dots for small surfaces. Press surfaces together and allow to cure. Sealant Apply product, ensuring it is forced into the joint, with good contact to surfaces. Tool with a soap solution before skinning occurs. Gap Filler Apply product into gap. Smooth off with spatula dipped in soapy water. Allow to skin before painting with water-based paints. Limitations: Not recommended for solvent-based paints. If required, paint with a water-based paint first. Tips: For neater joints, mask sides before applying sealant and remove tape before sealant skins. Larger, heavier items need to be supported until the adhesive cures. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface Clean up Uncured product may be removed with mineral turps. Cured product can be removed by scraping or sanding or with the help of Selleys Silicone Remover.
$16.52
Selleys Seal Fix forms gaskets/seals directly from the tube; any size, any shape. Selleys Seal Fix cures to a tough durable silicone rubber, and is ideal for repairing or replacing worn our seals in domestic ovens, fridges and freezer doors, as well as automotive and appliance gaskets. Seal fix is resistant to chemicals, oil, water, detergent etc. It is safe for incidental contact with food. Features: -High-Temperature resistance up to 260°C** -Durable clear rubber seal -Ideal for vertical applications -Impact resistant -Safe for incidental food contact. Where can this product be used? -Replacing oven door seals -Replacing refrigerator door seals -Dishwasher door seals -Washing machines -Automotive gaskets and seals -Heating and air conditioners -Flanges of all kinds What materials is this product suitable for? -Metal* -Paint/coated surfaces -Glass -Fibreglass How to use this product -Clear surfaces with Selleys BBQ Tough Wipes or Oven Wipes and allow to dry. -Pierce tube seal, fit nozzle and cut to size. -For repair or replacement of oven door seal or oven door glass: Apply Seal Fix to repair or replace seal or glass. -Once the seal or oven glass is fixed in place the repair should be allowed to cure for 7 days before using the oven. -For repair or replacement of refrigerator door seal: Apply Seal Fix to door, bring surfaces together and close door. -Once the seal is glued in place the door needs to be held firmly closed with tape. -Due to the strong magnetic hold of the door seal to the refrigerator body, the repair must be allowed 24 hours to cure before opening the door or subjecting to any stress For repair or replacement of gaskets: -Remove old gasket/seal material and thoroughly clean surfaces with mineral turpentine and dry. If adhesion of gasket is not required wipe mating surfaces with an oily cloth. -Pierce seal in the tube, fit nozzle and cut to size. Squeeze the bead of sealant onto one of the surfaces to be joined, around the perimeter of the part and around bolt holes. -Join parts together within 10 minutes and bolt down to the desired torque. If a thicker gasket is required assemble but do not tighten bolts for 24 hours. Material cures in 24 hours. (When disassembly is required, pry two flanges apart and remove old sealant before reassembly.) Clean Up -Uncured product may be removed with mineral turpentine. Cured product can be removed with Selleys Silicone Remover or by mechanical action. Handy tips -When eliminating cork gaskets, ensure that adequate clearance remains for mechanical parts e.g. valve rocker covers (do not fully tighten until sealant has cured) Limitations *Not for copper brass or galvanised metal surfaces **Not suitable for continuous exposure to temperatures above 205°C or intermittent (more than 2 hours) expose to temperatures above 260°C Not for exhaust manifold or for contact with gasoline or distillate Safety tips -Avoid contact with skin and eyes and breathing vapour -On contact, the uncured sealant can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice -May irritate sensitive skin. If skin contact occurs, wipe off immediately and wash with plenty of soap and water -Ensure use in a well-ventilated area -Product releases acetic acid while curing -For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764 766) or a doctor -For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site Storage and re-use -Store in a cool, dry, well-ventilated place and out of direct sunlight -Keep containers closed when not in use – check regularly for leaks
$13.00
When you need to mount something to a surface but want the option to remove it later, use Scotch® Removable Mounting range of products. Strong hold for a lasting impression with no damage when it comes time for removal. Hang posters, artwork or reminders instead of using pins and tacks. Holds up to 453g Mount posters, photos, kids artwork and other lightweight items Mount posters, photos, kids artwork and other lightweight items Photo safe, will not stain walls like putties Clear restickable mounting squares Specifications Adhesion Restickable/Reusable Mounting Brand Scotch® Colour Clear Indoor/Outdoor Indoor Length 2.5 cm Product Type Tabs Size 2.5cm x 2.5cm Width 2.5 cm
$6.50
Change your décor as quickly as inspiration strikes with Scotch® Removable Clear Double-Sided Mounting Squares. These convenient, invisible holds, squares let you mount your favourite photos, kids' artwork and to do lists with their easy stick-on design that doesn't damage your surfaces when it's removed. They're compatible with a variety of surfaces, from your walls to your child's locker, to your office window. So, keep on creating without regret with the undetectable secret assistance of Scotch® Removable Clear Double-Sided Mounting Squares. Removable and clear, use instead of push pins to keep your surfaces looking great Removes easily without leaving any residue on ideal surfaces To hold 1/4 lb use 2 Squares Designed for hanging and securing lightweight items including artwork, photos and cards Ideal for use on metal, glass, acrylic and finished wood Photo-safe (determined in accordance with ISO Standard 18916) Pre-cut squares for easy, mess-free application Ensure your surface is smooth, clean and dry for the best bond Great for school and crafting projects Made in the U.S.A with globally sourced materials Size: 11/16 in x 11/16 in squares Color: Clear
$6.50
Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Details Whether you're beautifying the exterior of your home, or reinforcing your mailbox, Scotch-Mount™ Outdoor Double-Sided Mounting Tape is the one to choose for a hassle-free, permanent bond. Designed to deliver exceptional adhesion, this powerful double-sided tape holds up to 15 pounds because of its 3M™ industrial strength adhesive. It's compatible with a variety of surfaces and conforms easily. If you are looking for a weather resistant way to quickly and easily mount or fix items outdoors, look no further than Scotch-Mount™ Outdoor Double-Sided Mounting Tape. Weather Resistant - High conformability adheres easily to your item and the surface Intended for outdoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lbs use 60" Designed For: Metal, Painted/Finished Wood, Vinyl Siding and Acrylic Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA from globally sourced materials Available in various sizes Color: Grey
$34.85
Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Specifications Brand Scotch-Mount™ Overall Width (Metric) 2.54 cm Product Colour White Details Scotch™ Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organise your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Easy-to-apply design with no mess or tools. Use instead of nails and screws Great for do-it-yourself projects
$15.99
Holds up to 4.5kg, 22cm holds 1kg Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Indoor/Outdoor Indoor Overall Length (Metric) 1.3 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Rolls Size 2.5cm x 1.3m Details Scotch™ Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch™ Indoor Mounting Tape.
$9.50
Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 1.2 cm Overall Width (Metric) 5 cm Product Colour Black Product Type Rolls Size 5cm x 1.2m Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.6kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$17.19
For your toughest jobs, go for our strongest hold–Scotch™ Extremely Strong Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies gravity, holding an item up to 20 pounds. It's weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organization to the garage, Scotch™ Extremely Strong Mounting Tape does the job quickly, easily and without the hassle of tools. Use instead of nails or screws Delivers a superior, conformable bond on contact A 60" roll holds up to 30 lbs. of objects. Not intended for use on an item that exceeds 20 lbs. Do not use on drywall or items that are more than .75” thick Easy-to-apply design with no mess or tools Ideal for use on finished/painted surfaces, metal, tile, laminate, plastic and more Ensure your surface is smooth, clean and dry for the best bond Apply at temperatures between 50°F to 100°F Made in the USA from globally-sourced materials Intended for indoor and outdoor use Color: Black
$36.63
Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Specifications Brand Scotch™ Indoor/Outdoor Indoor Product Type Mounting Strip Details This virtually invisible, professional-quality tape is designed for attaching items up to 4.5kg to any smooth wall or surface. It is perfect for discretely mounting items on glass, tile or mirrors. For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch™ Clear Mounting Tape. Virtually clear, this double sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer. So whether you're mounting acrylic cosmetic organisers or a translucent picture frame, affix it confidently with Scotch™ Clear Mounting Tape. Virtually clear design lets your décor take center stage Delivers a strong, permanent bond on contact Holds up to 15 lbs. Easy-to-apply design with no mess or tools Ideal for use on glass, metal, tile, plastic and more Intended for indoor and outdoor use Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials UV resistant colour: Clear
$14.24
Easily mount signs, plaques or house numbers using the Scotch™ Mounting Strips. They are weather resistant and can be used both indoor and outside. Your solution for a long lasting strong bond. Holds up to 2.7kg, 7.6cm holds 340g Mount a sign, mailbox or plaque without needing to use nails or screws Ideal for Indoor and Outdoor surfaces and applications Recommended Surfaces: Painted wood, painted bricks, metal, vinyl Uses 3M VHB™ Tape Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm
$8.81
Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm Details For your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 5.4kg, 17cm holds 1kg Hang or mount kitchen splashbacks, outdoor décor or organise your tool shed Ideal for both indoor and outdoor use, no need for nails and screws UV, temperature and humidity resistant Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for Drywall Waterproof once bonded to surface Uses 3M VHB™ Tape, Extreme strength and high conformability
$11.29
Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Specifications Brand Scotch™ Good For Outdoors No Indoor/Outdoor Indoor Overall Length (Metric) 2.5 cm Overall Width (Metric) 2.5 cm Product Colour White Product Type Squares Size 2.5cm x 2.5cm Details Scotch® Indoor Mounting Tape makes it so easy to beautify and organise your space quickly and easily. Whether you're creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape delivers a strong bond every time. Your work is up and ready to admire, no nails or hammer required. Never let how you're going to hang it get in the way of your creativity with the powerful adhesion of Scotch® Indoor Mounting Tape. Scotch® is the permanent mounting solution that is fast, easy and does not require the need for any tools. Holds up to 1.8kg, 2.5cm holds 113g, 10cm holds 453g Mount organisational caddies in the home office or kitchen, chalkboards, decorative signs or plaques Ideal for indoor use only, no need for nails and screws Double coated foam tape that isflexible, soft and conformable Bonds to any smooth, indoor surface Faster, safer, and more versatile than screws and nails Ideal for Indoor use on any smooth surface No need for any tools, nails or screws
$9.96
![Scotch 3M Mount Double Sided Squares Indoor 15lb x 48 [2.54cm x 2.54cm]](http://gluesaustralia.com.au/cdn/shop/files/051131769960N_f18dde17-9448-4437-aace-df5695c465e8.jpg?v=1754711993&width=645)
Scotch Indoor Double-Sided Mounting Squares are ideal for painted surfaces and allow you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, these permanent double-sided foam squares hold up to 15 pounds and deliver a strong bond every time because of their 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Squares. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3 squares To hold 15 lb use 45 squares Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White Specifications Size (Imperial) 0.5 in x 0.5 in, 1 in x 1 in
$8.89
Save your tools for another job, and mount your mirrors with the powerful adhesion of Scotch™ Mirror Mounting Tape. This double-coated tape permanently adheres to your mirrors and wall for quick, easy and accurate mounting. It's humidity-resistant, making it the ideal choice for bathrooms and kitchens. So the next time your décor calls for a mirror, mount it in a snap and don't forget to admire your reflection for a job well done with Scotch™ Mirror Mounting Tape. Intended for indoor use only Humidity-resistant adhesive provides a powerful hold in humid environments Delivers a strong, permanent bond on contact Holds up to 10 lbs. per 60”/(1 lb. per 6" of tape) Easy-to-apply design with no mess or tools Ideal for use on finished/painted surfaces, metal, tile and more Works best when applied between 50°-100° F Ensure your surface is smooth, clean and dry for the best bond Made in the USA from domestic and globally-sourced materials; packed in Mexico Size: 1 in x 60 in Color: White
$17.44
Scotch Indoor Double-Sided Mounting Tape is ideal for painted surfaces and allows you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, this permanent double-sided foam tape holds up to 15 pounds and delivers a strong bond every time because of its 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Tape. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3" To hold 15 lb use 45" Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White
$9.27
SANDING BLOCKS offer optimal sanding results on flat, contoured and irregular shapes. • Flexible, to conform to contours and irregular shaped objects. • For sanding and cleaning metal, wood, plaster, plastic, fibreglass etc. • Can be used for wet or dry sanding. • Rinse with water to clean.
$2.05
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
![RiteTack Instant Grab Construction Adhesive 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/0799439671669_6c8563d0-64cb-499e-a564-d2d4a62e9ce2.png?v=1754712007&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Grey]](http://gluesaustralia.com.au/cdn/shop/files/0793591712994_c9bef70a-42d0-408c-8b14-e176578d110d.png?v=1754712009&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
![RiteTack Instant Grab Construction Adhesive 290ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/0793591712987_0ace0873-9628-42fc-9b06-c64c93c74c40.png?v=1754712010&width=645)
Eliminates the need for unsightly fixings or tiresome clamping & propping Superior initial grab, up to 1000KGS per SQM horizontally Suits most materials including timber, metal, glass, mirror, plaster, stone, ceramic, concrete, PS, PU, PVC & polystyrene. No solvents & no isocyanate, user-friendly! Proven worldwide Paintable & retains elasticity Ritetack is an odorless and silicone, solvent, phthalate, PVC, and isocyanides-free, high-quality instant grip polymer adhesive designed for the building and construction industry, which performs. There is no need to wait while it cures since you only need to apply Ritetack, position it, and that’s it, no need for any type of braces. Ritetack is DIY and home improvement’s go-to glue. This instant grab adhesive works with most materials from stone and timber to steel and plasterboard, and more, it’s so easy to apply. Use it in with your caulking gun, like the Ritepro, on any job. If you want a glass adhesive, it is your answer. Less hassle, less labor, and fewer fixings. Used for mirror installation by the glass industry. Its coloured, elastic composition is a combination of cutting-edge adhesive technology and our market-leading easy-to-use design.
$9.95
Ultra-High strength supa glue that dries clear. Gives great strength as well as flexibility and heat resistance. Performance above and beyond normal Supa Glue. Features Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve an initial bond Self-piercing, clog-free cap Forms a strong, flexible bond Impact Resistant – 4 times greater impact resistance than normal supa glues Superior bond on metals – up to 6 times stronger bond on steel than normal supa glue. Up to 4 times stronger bond on aluminium than normal supa glues Heat Resistant to 120°C permanently, 150°C intermittently Comes with a nozzle for easy, accurate application Appearance Clear thick liquid dries to a colourless film. Where can this product be used? Ideal for small repair jobs or when immediate results are required Fixing a broken door knocker Refixing wooden or metal door handles Repairing crockery safe to put in the dishwasher Water resistant not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or other materials containing alkaline elements Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals Wood China Rubber Leather (test first as leather may become hardened or discoloured) Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Refer to handy hints for cleaning tips. Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. Allow 12 hours for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of materials if the area is not well ventilated. Clean the affected area with acetone to remove (most nail polish removers) residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in the opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from the skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin is soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary to apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.00
An all purpose, high strength household glue that unlike standard superglues is extremely ‘infinitely’ more flexible. It can repair and bond a variety of surfaces and withstand the most extreme/rough conditions whilst providing the ultimate bond. Features Strong Bond Ultra Flexible – infinitely more flexible* Extreme Resistance to: Shocks & Vibration, Torsion & Movement, Water and Extreme Temperatures Dishwasher Safe Gap Filling (works on uneven surfaces) Paintable Adjustable for 1min Non-Drip (great for vertical surfaces) Interior/Exterior Easy to use Heat resistant -15°C to +120°C Solvent free, no shrinkage Colour Dries translucent What materials is this product suitable for? Metal Wood Glass Rubber China Leather Ceramics Masonry Fibreglass Vinyl Cardboard Fabric Most plastics (will not bond polyethylene or polypropylene plastics; for these use Selleys Plastics Glue) Storage and re-use Wipe nozzle clean, replace cap & store in a cool dry place Safety Tips On contact, uncured adhesive can irritate eyes. If in eyes, flush with water for at least 15 minutes and seek medical advice. Avoid contact with skim. If contact occurs, wipe off and wash with detergent. Avoid breathing vapours. Use in a well ventilated area
$12.00
Quick Fix No Mess Stand Up Tube is the Supa Smart Supa Glue. The tube controls the flow of adhesive for precise applications and will retract partly dispensed glue from the nozzle so it will never clog up and dry out between uses. The stand up feature also means you don’t end up with messy drops of glue on the benchtop! Features -Free standing tube prevents leaks and retracts party dispensed glue -Prevents squeeze out and provides maximum application control -Bonds a variety of surfaces -Extremely fast setting, sets in 10 seconds -Maximum strength achieved in 12 hours -Dries clear for clean, neat results -Water resistant -No clamping necessary -Self piercing, clog free cap -Forms a rigid bond Where can this product be used? Ideal for small repair jobs or when immediate results are required For interior projects and repairs Water resistant not water proof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene Not suitable for repairing items that are in direct contact with hot liquids eg saucepans Will not permanently bond glass or materials containing alkaline elements Has no gap filling properties therefore surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Metals China Rubber Leather Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Pierce seal at end of tube by attaching nozzle and cap and turning clockwise. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. The product grabs within 2-30 seconds, depending on environmental conditions and materials to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Handy tips Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone (most nail polish removers) to remove residue. Excellent when used with other adhesives, as the temporary tack. For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (most nail polish removers) or Olive oil can also be used to remove Quick Fix from skin. While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Hand Kleen Wipes nearby for a quick and effective cleanup. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. Do not use near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$6.00
Fast setting ethyl cyanoacrylate (supa glue) based adhesive with a non-drip gel consistency which dries clear. Features -Bonds a variety of surfaces -Extremely fast setting -Dries Clear for clean, neat results -Water resistant -No clamping necessary -No mixing required -Maximum strength achieved in 12 hours -Only takes 45 seconds to achieve an initial bond -Self-piercing, clog-free cap -Forms a rigid bond -The non-drip gel consistency is ideal for vertical jobs -Can be used for gap filling due to the gel consistency Where can this product be used? -The non-drip gel consistency makes it particularly useful on vertical surfaces -Ideal for small repair jobs or when immediate results are required -For interior projects and repairs. -Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Leather may become hardened or discoloured -Not suitable for repairing items that are in direct contact with hot liquids eg saucepans -Will not permanently bond glass or materials containing alkaline elements What materials is this product suitable for? -Bonds a variety of porous and non-porous surfaces -Metals -Wood -China -Rubber -Leather (test first as some leather may become hardened or discoloured) -Some plastics How to use this product -Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible. -Surfaces to be bonded should be clean, dry and free of dust. -Pierce seal at end of tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. -The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded. -Allow 30 minutes for sufficient bond strength for practical use. Handy tips -Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue. -Use Quick Fix Gel on vertical surfaces. -Excellent when used with other adhesives, as the temporary tack. -For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. -After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. -Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would. -Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from skin. -Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions. -Super glues cure more slowly when large amounts are used. For faster cure use sparingly. -While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. -Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbant material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. -Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. Safety tips -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in skin. -Do not use near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non toxic when set -For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use After use, wipe excess product from nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. Ensure cap is replaced and store in a cool dry place. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$7.00
Fast setting ethyl cyanoacrylate (suclog-freebased adhesive with a non-drip gel consistency which dries clear. Features: -Bonds a variety of surfaces -Extremely fast setting -Dries Clear for clean, neat results -Water resistant -No clamping necessary -No mixing required -Maximum strength achieved in 12 hours -Only takes 45 seconds to achieve an initial bond -Self-piercing, clog-free cap -Forms a rigid bond -The non-drip gel consistency is ideal for vertical jobs -Can be used for gap filling due to a gel consistency Where can this product be used? -The non-drip gel consistency makes it particularly useful on vertical surfaces -Ideal for small repair jobs or when immediate results are required -For interior projects and repairs. -Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet -Not suitable for bonding plastics such as Polypropylene and Polyethylene -Leather may become hardened or discoloured -Not suitable for repairing items that are in direct contact with hot liquids eg saucepans -Will not permanently bond glass or materials containing alkaline elements What materials is this product suitable for? -Bonds a variety of porous and non-porous surfaces -Metals -Wood -China -Rubber -Leather (test first as some leather may become hardened or discoloured) -Some plastics How to use this product -Supa Glue non-drip gel works best when the surfaces to be bonded are close fitting, but a small amount of gap filling is possible. -Surfaces to be bonded should be clean, dry and free of dust. -Pierce seal at end of the tube by attaching nozzle and cap and turning clockwise. -Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. -The product grabs within 2-30 seconds, depending on environmental conditions and substrates to be bonded. -Allow 30 minutes for sufficient bond strength for practical use. Handy tips -Supa Glue can create a white residue on the surface of a material if the area is not well ventilated. Clean the affected area with acetone, to remove residue. -Use Quick Fix Gel on vertical surfaces. -Excellent when used with other adhesives, as the temporary tack. -For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting. -After use, wipe excess product from the nozzle with a tissue dipped in nail polish remover. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. -In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. -Quickfix gel is good for use on wood & porous surfaces (e.g terracotta pots) as it doesn’t soak into the surface like a liquid would. -Acetone ( most nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin. -Since Quick Fix cures with moisture, set times may be extended on very dry surfaces or under dry conditions. -Super glues cure more slowly when large amounts are used. For faster cure use sparingly. -While supa glue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24 hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. To remove excess from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Do not squeeze tube before removing the cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into the cap, preventing a tight seal after use. Safety tips -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. -Do not use near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set -For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use -After use, wipe excess product from the nozzle with a tissue dipped in acetone (found in some nail polish removers). Wait for a few seconds and check that no further glue is extruding before replacing cap tightly. -Ensure cap is replaced and store in a cool dry place. -For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$3.78
Fast setting liquid supa glue in a self-standing bottle with brush applicator. Dries clear. Features Bonds a variety of surfaces Extremely fast setting Dries Clear for clean, neat results Water resistant No clamping necessary No mixing required Maximum strength achieved in 12 hours Only takes 45 seconds to achieve an initial bond Ideal for craft and collage applications Forms a rigid bond Easy to spread over wider areas from a stable self-standing bottle Where can this product be used? Useful for jobs with a wide surface area in both a repair and create capacity. Water resistant, not waterproof, therefore not suitable for surfaces that will be continually wet Not suitable for bonding plastics such as Polypropylene and Polyethylene. Leather may become hardened or discoloured For interior use only Not suitable for repairing items that are in direct contact with hot liquids Will not permanently bond glass or materials containing alkaline elements. Has no gap filling properties, therefore, surfaces need to be a close fit Not recommended for highly porous surfaces What materials is this product suitable for? Bonds a variety of porous and non-porous surfaces Metals China Rubber Leather Some plastics How to use this product Supa Glue works best when the surfaces to be bonded are close fitting. Surfaces to be bonded should be clean, dry and free of dust. Remove cap and apply a small amount of glue to one surface. Bring surfaces together and apply slight pressure. The product grabs within 10-60 seconds, depending on environmental conditions and substrates to be bonded. Allow 30 minutes for sufficient bond strength for practical use. Ensure cap is replaced immediately after applying adhesive, as this prolongs the life of brush applicator. Handy tips Cyanoacrylate adhesives can create a white residue on the surface of a substrate if the area is not well ventilated. Clean the affected area with acetone to remove residue. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight. Excellent when used with other adhesives, as the temporary tack For best results, ensure surfaces to be bonded are clean, free of dust, dry and close fitting In the event that fingers get stuck together – don’t panic! Slowly twist fingers in opposite direction in hot soapy water. Acetone (nail polish remover) or Olive oil can also be used to remove Quick Fix from the skin. While superglue is not recommended for use on some plastics, if your kids have broken their favourite toy, try this method: Line up the two pieces, glue it, leave it for 24hours to dry, then drop more glue on the break area like a ‘collar’/protective layer. Since Quick Fix cures with moisture set times may be extended on very dry surfaces or under dry conditions. Super glues cure more slowly when large amounts are used. For faster cure use sparingly. To remove excess from substrates, it is recommended that the material is soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Where soaking is not possible, try placing a piece of absorbent material (eg cotton wool) soaked in acetone on the excess for 5 to 10 minutes, topping up the acetone if it evaporates. Gently rub the surface with the material to remove the residues. TEST THE SURFACE IN AN INCONSPICUOUS SPOT to ensure it is unaffected by acetone before attempting removal using this method. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Quick Fix Supa glue bonds on contact, if fingers should stick together, apply a solvent such as acetone to affected areas and wash off with water. If no solvent is available wash area with warm soapy water and work fingers apart. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non-toxic when set Quick Fix is non-hazardous once cured. Where Quick Fix residues are on the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. Alternatively, rub in hand cream or vegetable oil to accelerate the natural process of the skin sloughing off to remove the residue. Where immediate adhesive removal is considered necessary apply a solvent such as acetone (nail polish remover) then wash off with soapy water. Apply hand cream to replace naturals oils in the skin. Storage and re-use After use, tap bottle lightly on a flat surface to clear excess product from the nozzle. Ensure cap is replaced and store in a cool dry place. Store Upright. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$9.01
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$19.17
A two-part gap filler and binder for builders and tradesmen that is a safe alternative to the toxic solvent and styrene-based fillers and bogs on the market. Environmentally friendly and non-hazardous for safe handling and easy transport Easy to mix, spread on rough and smooth substrates immediately Rapidly sets in 15 mins (faster in warm weather) with minimal shrinkage Curing time approximately 60 minutes • Long shelf life when firmly sealed after each use Once cured it may be chiselled, filed, sawn, planed and sanded into shape Can also be nailed, drilled, screwed, glued and painted Highly recommended for waterproofing as gap filler for bathroom renovations and other wet area applications where tiling or painting is required
$24.90
In keeping with the traditional formula, PREP Linseed Oil Putty is manufactured to the highest standards for almost all situations where a reliable linseed oil-based putty is required. Applications include; window glazing, filling nail holes in furniture, flooring, and general building applications. Environmentally friendly Non-toxic Tough & flexible Easy to use Weather-resistant
$7.50
Takes the stick out of stickiness. Makes taking off adhesive bandages easier.
$8.60
Prep marathon is the ultimate metal big-wig in crevices and corners. A scrub that trims down, it gets into the nooks to clean while also protecting with a silicone shield. It’s tough on calcium, rust and scale deposits which makes it ideal for use on tiles, porcelain sinks bathrooms and showers or baths. Get Prep Marathon today!
$4.00
There's a lot of grime to be wary of in this world, and there's no reason you should have to put up with it. Prep marathon gets your day off on the right foot by getting your house clean as a whistle again. Reach out today for this hardworking citrus-based cleaner that intensively degreases stubborn messes and is tough enough to tackle kitchen grease spills with ease. And because we use non-petroleum solvers, our lotions are less drying than most brands while still being gentle on hands. Get Prep Marathon Re-Moove-It Cleaner now!
$6.00
Clean the glass and brighten your shower in one go. Prep Marathon Glass Cleaner is a tough enough cleaner to remove streaks from surfaces, but gentle enough for laminates, chrome or any other delicate surface. If you're looking for an easy way to start off every home clean on the right track, order Prep Marathon Glass Cleaner now!
$16.15
No one likes those big, ugly streaks on their favorite mirror--trust us. Make sure your streak-free shine is up to snuff with a bottle of Prep Marathon Glass Cleaner before you start sweating for that marathon! The product is PH balanced and has been laboratory tested. You deserve an honest cleaning every time you use it, which can be easily achieved with this top selling solution!
$4.78
Clean the glass and brighten your shower in one go. Prep Marathon Glass Cleaner is a tough enough cleaner to remove streaks from surfaces, but gentle enough for laminates, chrome or any other delicate surface. If you're looking for an easy way to start off every home clean on the right track, order Prep Marathon Glass Cleaner now!
$6.00
Directions: Well recognised as a cleaning agent, can be used undiluted but traditionally in a diluted form 50/50 with water Uses: General cleaning, glass services & safe on stainless steel. Also safe to use in food preparation areas
$9.47
Prep Marathon is the perfect product for anyone who hates dirtying their hands when cleaning. Our BBQ cleaner combines hunger and cleanliness with a fresh scent to leave your dishes shining like new. When it comes to cooking, this easy prep option is ideal for making sure all of popsicles have made it into mouths safely- but also neat enough to make your house feel like royalty after you're finished!
$4.00
Prep Bi-Carb Cleaner makes stainless sinks shine, tiles sparkle and removes soap scum in showers. Use in the kitchen on benches, cook tops, laminate cupboard doors Deodorise upholstery and carpet by sprinkling with Bi-Carb, letting it sit for 15 minutes, then vacuum it up
$7.22
Directions: - Use gloves before dispensing - Washing Machines: empty machine, add 1 tablespoon of Descaling powder directly into the machine, not detergent dispenser. Run full cycle - Dishwashers: remove all items from the machine, including all dishwashing detergents. Fill detergent dispenser with up to 2 tablespoons of Descaling powder and run for a full cycle. - All-purpose cleaner: 1 tablespoon mix to 1 Litre hot water and soak items for up to 3 - 5 minutes, rinse the solution off in cold water Uses: Can be used undiluted for heavy stains by simply adding power and rob directly onto affected area e.g. bathtubs, sinks and toilet bowls
$11.48
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$13.53
A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$46.19
A paint and varnish stripper free of Methylene Chloride (MC) and N-methyl Pyrollidone (NMP) for safer interior usage*. Deep penetration performance allows for multiple layers to be stripped in a single application to save time. FOR INDOOR & OUTDOOR USE Coverage: 0.5m2 per litre when applied 2mm thick on a horizontal surface. Ready to use: YES NOTE: Do not use on plastic surfaces, vinyl, masonite or rubber. Take care when using on plasterboard or other porous surfaces as softening or penetration of the surface can occur. Suitable for most decorative paints, varnishes and 1-part polyurethanes. Not for Kalsomine, penetrating timber stains or some 2-pack coatings. *in comparison with methylene chloride paint strippers • Use in a well-ventilated area and wear protective gloves and glasses. • Apply stripper approx 2mm thick using a brush. Take care on vertical or overhanging surfaces, as stripper may drip. • Leave the paint stripper in contact with the coating until softened and scrape off the coating with slight pressure. If paint remains after scraping, apply a second coat of stripper. Scrape along the grain for timber. A scourer can be used to remove ingrained paint. • Stripping times vary according to a number of paint layers, age and type. As a guide, water-based paints begin to soften after 15–20 mins. Allow 60 mins or longer for oil-based and polyurethane coatings. The paint stripper remains effective while in a wet state. • Do not allow stripper or softened paint to dry on the surface. Some oil-based paints will continue to bubble and strip even after stripper has been removed. • Wipe surface clean with a wet rag followed by a solution of Poly Sugar Soap. Do not use excessive water. On fine timber where grain swelling is likely, use methylated spirits. • Allow surfaces to completely dry before re-coating. • Clean tools in warm water. SAFETY • Risk of serious damage to eyes. • Avoid contact with skin and eyes. Wear protective gloves and glasses when mixing or using. • If skin or hair contact occurs, remove contaminated clothing and flush skin and hair with running water. • Avoid breathing vapour. Use in a well-ventilated area. • Wash hands after use. • Keep away from heat and ignition sources. • This product has been classified as hazardous. Refer to Safety Data Sheet for more information. • If swallowed, do NOT induce vomiting. If in eyes, wash out immediately with water. • For first aid advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor at once. Q. What is the difference between Polystrippa Paint Stripper and Polystrippa Advanced? A. Polystrippa Paint Stripper is formulated with methylene chloride. It is very aggressive and may be harmful to health with prolonged exposure. It is most suitable for smaller applications and should only be used outdoors. Polystrippa Advanced, on the other hand, is free of methylene chloride and is preferable for larger or indoor applications.
$30.88
Permanently joins metals, wood, plastics, ceramics, glass, vulcanized rubber, leather, fabrics, and plaster Pliobond sets fast, is Permanent Stays flexible and won't become brittle
$25.00
A 15-minute, two-part adhesive and filler system that eliminates the need for welding or brazing. It repairs, fills and bonds to iron, steel, brass, bronze, aluminum and copper. Once cured, it can be drilled, tapped, threaded, filed, sanded and painted. Resists most automotive, shop and cleaning fluids. Withstands temperatures to 300°F intermittent. Over 3,000 PSI shear strength on steel. Automobile Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Heavy Duty Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Marine Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings PRODUCT BENEFITS • No heating required • Holds in 10 minutes • Useable in 30 minutes • Good moisture resistance • Withstands extreme temperatures • Non-flammable TYPICAL APPLICATIONS • Cracked transmission cases • Chipped heads • Rear end castings • Cracked blocks • Cracked intake manifolds • Damaged keyways • Split stampings DIRECTIONS FOR USE 1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease and oil. 2. Roughen smooth surfaces to be repaired with sandpaper. 3. Apply in ventilated area. Vapors may irritate eyes and nose. 4. Squeeze out equal amounts of bonding agent and curing agent. 5. Mix together thoroughly until color is uniform. 6. Apply immediately to both surfaces and press together. Remove excess glue at once. 7. Allow bond to set for 10 minutes before moving or handling. 8. After 24 hours, typical shear strength on steel is 3000 PSI. 9. Cure time will be slower in colder weather. For Cleanup 1. Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup. 2. Clean hands with Permatex Fast Orange hand cleaners. Chemical / Solvent Resistance The product retains effective properties when in contact with water, oil, fuels, and most solvents. Not recommended for long term exposure to chemicals and solvents. NOTE: Permatex Cold Weld Bonding Compound will not bond polyethylene and polypropylene plastics. GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
$23.00
You have seen 432 out of 666 products
Find products tagged for use on metal. This collection includes adhesives, sealants, tapes and accessories chosen for typical repairs and installs on metal surfaces. Compare cure speed, flexibility, clarity and temperature ratings to match your project. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
