This product is a quality PVA glue suitable for general woodworking. It is non-toxic, will not stain timber and dries clear. Suitable for Wood, Particle Board, Unglazed Pottery, Laminating, veneers, paper, cardboard, leather, foam and cloth Directions: Ensure all surfaces are clean, dry and free of oil, grease and wax Shake well before use Only apply to one surface Press surfaces together while the adhesive is still wet and clamp lightly (approx 2 to 4 hours in normal conditions) Remove excess glue with a damp cloth Great strength is achieved when dried overnight Cleaning: Clean up with water. Wash hands after use
$52.43
Instant, crystal clear bonds that are water and dishwasher-resistant. Formulated to work on all types of glass. Recommended on: Glass, Crystal, Tinted Glass, Glass Works, Opaque Glass, Blown Glass. Properties: Bonds glass to glass Glass to metal Stained glass Crystal and tinted glass Water and dishwasher resistant Bonds in seconds Dries transparent for invisible bonds Easy to open, self-piercing and anti-clog cap Solvent-free Step by Step: Ensure surfaces to be joined are clean, completely dry and close fitting Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set Replace the cap immediately and store upright in a cool dry place. How to Repair a Glass Water Jug? Loctite Super Glue Glass has been specially formulated to repair glassware, delivering a sparkling performance every time. Once dry it forms crystal clear bonds on all types of glass breakages and cracks, delivering water and dishwasher resistant seals that are not only neat and free from unsightly white glue marks but also strong enough to resist pressure from temperature changes and water. Loctite Super Glue Glass is designed to work on all kinds of glass: glass, crystal, tinted glass, glass works, opaque glass and blown glass, and has a high strength formula that ensures you get long-lasting durability. Follow the step by step application guide: 1.Wash the broken area with water (avoid using detergent as this can affect the glue's performance) and dry thoroughly. Ensure that the surfaces to be joined are close fitting. 2.Carefully squeeze a small drop onto one of the broken parts. Press both surfaces together firmly and wait until they is set. 3.Do not move until the surfaces are set. Don’t worry if there is some excess glue, this can be easily removed once dry (see point 5) 4.Allow at least 1-2 hours to fully cure before using. For best results leave overnight. 5.Once dry, if there is any excess residue, gently wipe with a tissue dipped in Loctite Glue Remover or nail varnish remover containing acetone. 6.Replace the cap immediately and store the glue upright in a cool dry place.
$8.28
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_1ec2ac38-d5ee-448a-869a-ebd682688cb3.jpg?v=1754715959&width=645)
![Loctite Kintsuglue Flexible Putty 3 x 5g [White]](http://gluesaustralia.com.au/cdn/shop/files/5010305059189_e15aa915-f631-45bf-a31f-e1c90de968b7.jpg?v=1754715959&width=645)
Kintsuglue is an amazing paste created to fix almost any broken object. Shapeable, strong and flexible after curing, it can be applied to all the things you want to repair, reconstruct, protect or enhance. It restores the functionality of objects and treats repair as part of an object´s life, rather than replacing them. Take it Clean your hands and make sure all surfaces are dry and free of dust and grease. Shape it Knead Kintsuglue for about 10 seconds and then give the paste the desired shape before applying. Apply it Apply the paste to the surface you want to bond or protect. You have up to 30 minutes to adjust it before it starts curing! To get the best result, let it harden overnight.
$23.52
Introducing Gorilla Fabric Glue - Your Ultimate No-Sew Solution! Say goodbye to tedious needle and thread work and embrace the power of Gorilla Fabric Glue! This remarkable adhesive is a 100% waterproof, no sew solution for all your fabric needs. From hems to embellishments, trim, and more, Gorilla Fabric Glue is your go-to partner for crafting and repairing with ease. Experience the magic of a fast-setting, permanent bond with Gorilla Fabric Glue! Designed to tackle even hard-to-hold embellishments, this adhesive ensures your fabric creations stay intact for the long haul. Once cured, it remains flexible, allowing your fabrics to move naturally without losing durability. Prepare to be amazed by the crystal clear finish! Gorilla Fabric Glue dries clear, leaving no unsightly traces behind. Plus, it's washer and dryer safe, so your creations can endure countless washes without losing their strength. Crafters, rejoice! Gorilla Fabric Glue boasts a no-run formula, making application a breeze. Say goodbye to messy mishaps and hello to seamless, professional results. Versatility is its middle name! Gorilla Fabric Glue bonds with various surfaces, including fabric, felt, beads, wood, canvas, ribbon, sequins, and more. Whatever your creative vision, Gorilla Fabric Glue has got you covered. Directions for Use: For optimal results, always test on a scrap of the intended fabric. Pre-wash the fabric without using fabric softener. Use the adhesive between 10°C and 32°C for best performance. Apply the Gorilla Fabric Glue to each surface to be bonded. To maximize bond strength, wait approximately two minutes for the adhesive to partially dry before joining the surfaces. Press the surfaces firmly together. *Note: The bond forms immediately and can be difficult to reposition, so precision is key. Cure Time: Allow for a minimum of 24 hours for full cure. For washing and ironing, wait a minimum of 3 days after bonding. For washing, use a delicate cycle, and for drying, choose low or no heat settings. Storage Tips: After each use, wipe the nozzle with a dry cloth and tightly replace the cap. Store Gorilla Fabric Glue in a cool, dry location, away from children and animals. For easier re-opening, apply a thin coat of petroleum jelly to the threads before replacing the cap. Clean-Up: Wipe any uncured adhesive with a dry cloth and clean the surface with acetone, isopropyl alcohol, or citrus-based solvents following the manufacturer's instructions. For a clean surface after curing, gently scrape off the cured adhesive. Technical Specs: Application Temperature: 10°C to 32.2°C, best at room temperature Outdoor: Yes Moisture Resistant: Waterproof Paintable: Yes – compatible with water and oil-based paints, and spray paint Sandable: Yes Stainable: Yes Cured Color: Clear Bring your fabric creations to life with Gorilla Fabric Glue! Embrace the simplicity, durability, and versatility of this game-changing adhesive. Crafters, DIY enthusiasts, and repair wizards alike can now achieve professional results without a single stitch. Join the Gorilla Glue family and take your fabric projects to new heights of excellence! FAQS How should Gorilla Fabric Glue be stored? After each use, wipe nozzle with a dry cloth and tightly replace cap. Store in a cool, dry location. Tip: for easier re opening, apply a thin coat of petroleum jelly to the threads before replacing cap. What surfaces does Fabric Glue adhere to? Gorilla Fabric Glue can be adhered to many surfaces including: Fabric, Felt, Beads, Wood, Canvas, Ribbon, Sequins, Leather, Paper, Foam and Rubber *NOTE: Not recommended for use on polystyrene, polypropylene or polyethylene products. Not for use on food contact surfaces. Do not dry clean. May cause damage to finished surfaces. Is Gorilla Fabric Glue food safe? Fabric Glue should not be used around food. How do you clean up Gorilla Fabric Glue? When using Fabric Glue, it is best to wear safety glasses and chemical resistant gloves. To clean uncured adhesive: wipe uncured adhesive with a dry cloth and clean with acetone, isopropyl alcohol, or citrus based solvents according to manufacturer’s instructions. Cured adhesive may be removed by scraping from surface. See first aid treatment for skin contact. Is Gorilla Fabric Glue gap filling? No Is Gorilla Fabric Glue UV Resistant? Yes Is Gorilla Fabric Glue stainable? Yes, Gorilla Fabric Glue is stainable when fully cured. Is Gorilla Fabric Glue sandable? Yes, cured Gorilla Fabric Glue is sandable. Is Gorilla Fabric Glue paintable? Yes, when fully cured. Is Gorilla Fabric Glue Washer/Dryer safe? Yes Is Gorilla Fabric Glue photo safe? Gorilla Fabric Glue is safe to use with photos.
$16.88
Note :If you are working on a wooden floor, you will need to use the Fix-A-Floor Polyurethane For Loose, Squeaky Wood Flooring Repair. You can purchase it here. Fix-A-Floor Repair Adhesive " Now Patented", is an Extra Strength Bonding Adhesive customized for the specific use of Re-Bonding loose and hollow tile, marble & stone without the expense and mess of removing or replacing them. Fix-A-Floor is a simple do it yourself repair that is fast, easy and affordable not to mention fun and quite rewarding to anyone who can operate a drill, caulking gun and mix up a small batch of grout. Works on all sub-floor materials. Just Drill & Fill! The TipThe Tip of the 10.1 oz. Fix-A-Floor tube has been specially designed and engineered with a pre-drilled 1/8" hole for the sole purpose of filling drilled holes in loose & hollow tile, marble & stone floors. The Tip is extra firm and allows for a strong seal which promotes good flow and complete coverage. The 1/8" pre-drilled tip allows for use in narrow grout line applications or wider. It has marked lines showing clear cut points of 3/16", 1/4" or any other size you may need. The AdhesiveFix-A-Floor Repair Adhesive is Strong & Flexible with elastomeric bonding properties to eliminate any future problems due to foundation settlement, expansion & contraction of the sub floor as well as poor original installation... Used by professionals for years, now YOU can fix your loose & hollow, squeaky floors with Fix-A-Floor!!! Fix-A-Floor is Non-Toxic, Non-Flammable & Eco-Friendly! Large problem area or small problem areas are no problem with Fix-A-Floor! Guaranteed for the life of your floor! Just Drill & Fill! FAQs Q: Will Fix-A-Floor work if I have heated floors?A: Yes! We have customers using Fix-A-Floor with heated floor elements all the time with no problems. Keep heating element off before, during & for 48 hrs. after applying. Q: Some of my grout is missing or completely gone? How can I use Fix-A-Floor?A: If bits and pieces of grout are missing here and there around the problem area, just go ahead and Drill & Fill, the adhesive will actually help to re-bond the bits that are cracking and loose. If your grout is completely gone we recommend lightly re-grouting the area allow to dry and then Drill & Fill! Q: Can I use Fix-A-Floor to fix my entire floor or just a small area?A: Fix-A-Floor works great on all size problem areas from 1 tile to the whole entire floor! Works on all types of Tile, Marble & Stone floors too! Q: Can I use Fix-A-Floor outside on my patio or deck?A: Yes! Fix-A-Floor works beautifully on interior and exterior applications. Q: Can I use Fix-A-Floor in my shower or Pool?A: No! Fix-A-Floor is not recommended for areas with exposed to excessive moisture. Q: Is Fix-A-Floor Safe?A: Yes! Fix-A-Floor is a non-toxic, non-flammable and Eco-Friendly water-based adhesive. Q: Can I use Fix-A-Floor to re-glue a tile that is off the floor?A: Yes, simply squeeze Fix-A-Floor onto the floor where the tile was and press the tile back down onto the floor, place weight and allow to dry for 24 hrs. Tile will be rebonded! Q: Do I have to place buckets of water on my floor after I Drill & Fill?A: It is recommended you place some kind of weight on the area to aid in curing and to be sure no excess adhesive is trapped under your floor before regrouting. It is not mandatory. Q: What if I don’t see the adhesive coming up out of the other holes?A: While filling Fix-A-Floor will usually come up and out of the other drilled holes. If this does not happen move to another hole and continue to fill, the adhesive is still travelling under the floor. If you see the adhesive coming back up out of the hole you are filling, be sure you are NOT pressing the tip of the tube down onto the subfloor. Q: What if the adhesive is clumpy or not flowing out of the tube properly?A: The adhesive in the tube has frozen either in transit during the cold winter months this can happen. Simply contact us for a replacement.
$599.00 $429.50
Clear Boyle Craft Glue Boyle Craft Glue (Clear) is a versatile, water-based adhesive designed for everyday making and detailed craft work. It dries clear and odourless, making it perfect for neat, mess-free results on paper projects, school assignments, scrapbooking, model making, décor builds and more. Why You’ll Love It Dries crystal clear for a clean, professional finish. Water-based & odourless for a low-fuss, indoor craft experience. Heat & light resistant—ideal for display pieces exposed to room lighting/sunlit interiors. Easy-squeeze bottle gives smooth, controlled bead lines and spot application. Cleans up with water—simply wipe while wet for quick tidy-ups. Suitable Materials Formulated for strong, reliable bonds on: Paper, cardboard & posters Wood, balsa & craft sticks Plastics* Glass & ceramics Metal embellishments Fabrics & felt Yarns, beads & sequins Leather and more *Always test first—some low-energy plastics may require light surface prep. Great For School projects & classroom crafts Cardmaking, scrapbooks & photo boards DIY décor, event styling & mood boards Miniatures, models & hobby builds Textile embellishment on felt and fabric (non-washwear items) How to Use Prep: Ensure surfaces are clean, dry and free of dust or oils. Lightly roughen very smooth surfaces for best grab. Apply: Squeeze a thin, even layer to one surface. For porous materials (paper, cardboard, wood), a little goes a long way. Assemble: Press parts together. Use light pressure, clips or tape if needed to hold while setting. Dry: Allow to dry thoroughly. Dry time varies with bead thickness, temperature and humidity. Clean-up: Wipe excess immediately with a damp cloth. Wash tools in water while glue is still wet. Good to Know Indoor use: Formulated for indoor crafting and display. Clear finish: Dries transparent to help hide glue lines and squeeze-out. Heat & light resistance: Helps projects maintain appearance under typical indoor conditions. Washes out with water: Clean hands, tools and fresh spills while wet. Specifications Base Water-based Appearance (dry) Clear Odour Odourless Cleanup Water (while wet) Use Indoor Tips & Testing For non-porous surfaces (glass, metal, some plastics), apply a thin coat to each surface, wait briefly, then join for better grab. Always perform a small test on off-cuts or an inconspicuous area to confirm compatibility and finish. Avoid heavy, load-bearing or structural applications—this is a craft-grade adhesive. FAQs Does it dry clear?Yes—Boyle Craft Glue dries clear for a neat finish. Can I wash it out?Yes—while wet, it washes out with water. Once fully dry/cured, removal may be more difficult. Is it suitable outdoors?It’s designed for indoor craft projects. For outdoor or constantly wet environments, choose a weather-rated adhesive.
$15.62
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$18.00
Instant, crystal clear bonds that are water and dishwasher-resistant. Formulated to work on all types of glass. Recommended on:Glass, Crystal, Tinted Glass, Glass Works, Opaque Glass, Blown Glass. Properties:Bonds glass to glassGlass to metalStained glassCrystal and tinted glassWater and dishwasher resistantBonds in secondsDries transparent for invisible bondsEasy to open, self-piercing and anti-clog capSolvent-free Step by Step: Ensure surfaces to be joined are clean, completely dry and close fitting Twist cap clockwise until it locks, then unscrew in an anti-clockwise direction to open Carefully squeeze a small drop onto one surface. Press the surfaces together and hold until set Replace the cap immediately and store upright in a cool dry place. How to Repair a Glass Water Jug?Loctite Super Glue Glass has been specially formulated to repair glassware, delivering a sparkling performance every time. Once dry it forms crystal clear bonds on all types of glass breakages and cracks, delivering water and dishwasher resistant seals that are not only neat and free from unsightly white glue marks but also strong enough to resist pressure from temperature changes and water. Loctite Super Glue Glass is designed to work on all kinds of glass: glass, crystal, tinted glass, glass works, opaque glass and blown glass, and has a high strength formula that ensures you get long-lasting durability. Follow the step by step application guide:1.Wash the broken area with water (avoid using detergent as this can affect the glue's performance) and dry thoroughly. Ensure that the surfaces to be joined are close fitting.2.Carefully squeeze a small drop onto one of the broken parts. Press both surfaces together firmly and wait until they is set.3.Do not move until the surfaces are set. Don’t worry if there is some excess glue, this can be easily removed once dry (see point 5)4.Allow at least 1-2 hours to fully cure before using. For best results leave overnight.5.Once dry, if there is any excess residue, gently wipe with a tissue dipped in Loctite Glue Remover or nail varnish remover containing acetone.6.Replace the cap immediately and store the glue upright in a cool dry place.
$8.95 $8.78
Glitz Waterless Hand Sanitiser Quick Dry Antibacterial 500ml Keep hands clean anywhere with Glitz Waterless Hand Sanitiser. This quick dry, rinse free antibacterial gel helps reduce germs on contact and leaves hands feeling fresh without sticky residue. Ideal for homes, workplaces, classrooms, retail counters, and on the go. Why choose it Fast acting formula that helps kill common household germs Waterless design for convenient use when sinks are not available Quick dry finish that does not feel tacky Light, fresh scent suited to frequent use Family friendly 500ml pump that is easy to share Best for After public transport, shopping, or handling deliveries Before eating or preparing food when a sink is not nearby Office desks, reception areas, classrooms, workshops, and vehicles How to use Apply a small amount to dry hands. Rub hands together, covering palms, backs of hands, between fingers, and around nails. Continue rubbing until completely dry. No rinsing required. Pro tips Use enough product to keep hands visibly wet for at least 20 seconds. Reapply after touching high contact surfaces or as needed. Pair with regular hand washing for the best hygiene routine. Safety For external use only. Keep out of reach of children. Avoid contact with eyes. If contact occurs rinse with water. If irritation occurs discontinue use and seek medical advice. Flammable. Keep away from heat and open flame. Store below 30°C. Product details Brand Glitz Product type Waterless hand sanitiser gel Size 500ml Format Pump bottle for easy dispensing Finish Quick dry, non sticky Fragrance Light fresh scent Use No water required. Leave on. Areas Home, office, retail, school, workshop, car Storage Store upright with cap closed. Keep away from heat sources. Frequently asked questions Does it require waterNo. Apply to dry hands and rub until fully dry. Can children use itYes, under adult supervision. Ensure hands are rubbed until dry. Will it replace hand washingUse as a convenient option when soap and water are not available. Wash with soap and water whenever hands are visibly soiled. What is included 1 x Glitz Waterless Hand Sanitiser Quick Dry Antibacterial 500ml Good to know Great value size for shared spaces and busy families Fits neatly on counters and reception desks Ideal to keep one at home and one in the car
$9.85 $8.39
Get sharp, clean paint edges with Paint Partner Thick Masking Tape. This reliable painter’s tape is designed to stick firmly, remove cleanly within the recommended time, and resist paint bleed for professional looking results on walls, ceilings, trims, doors, and furniture. Crisp paint lines with reduced bleed on properly prepared surfaces Thicker construction for easy handling, straight tearing, and consistent edging Clean removal within the recommended timeframe to help reduce residue Suitable for most interior paint systems including acrylic and enamel Value 6 pack for multi room or multi day projects Ideal For Masking skirting boards, window frames, architraves, and cornices Two tone feature walls and colour blocking Furniture upcycling and detailed trim work Protecting hardware and fixtures during repainting Specifications Brand Paint Partner Product Thick Masking Tape for Crisp Paint Lines Width 24 mm Length per roll 27 m Pack size 6 rolls Adhesive type Pressure sensitive Surface types Painted drywall, timber trim, metal, glass, and sealed surfaces Use Interior masking and edge definition Removal window Remove within the recommended project timeframe for clean results Colour Neutral masking tape How to Use Prep the surface Ensure it is clean, dry, and free of dust or grease. Lightly sand and wipe where needed. Apply the tape Align to the paint edge and press down firmly, smoothing along the full length to seal the edge. Paint Apply paint in light coats, brushing or rolling away from the tape edge to reduce bleed. Remove While paint is still slightly tacky or once fully dry per paint instructions, peel the tape back on itself at a 45 degree angle. Pro Tips Burnish the tape edge with a clean cloth or plastic card for the sharpest lines. For textured walls, apply a very light coat of the base colour along the tape edge, let it set, then apply the top colour. Test in a small, hidden area on delicate or freshly painted surfaces. What’s in the Pack 6 rolls of Paint Partner Thick Masking Tape, each 24 mm x 27 m. Storage and Safety Store in a cool, dry place away from direct sunlight. Use on fully cured paint only. Always test before full application. Dispose of used tape in household waste according to local guidelines. Frequently Asked Questions Will it pull off existing paintWhen applied to properly cured paint and removed within the recommended timeframe, it is designed for clean removal. Always test on a small area first. Can I use it outdoorsBest suited for interior projects. For extended outdoor exposure consider a UV resistant painter’s tape. How do I get the sharpest edgePress the tape down firmly along the edge and remove at a 45 degree angle while paint is slightly tacky or fully cured as directed by the paint manufacturer. Why Buy From Glues Australia Australian based support and fast dispatch Carefully curated paint preparation range Competitive pricing on multi pack project essentials
$9.65 $7.87
Tarzan’s Grip Multi-Purpose General Adhesive 250 g is a reliable versatile contact style adhesive for crafts and household fixes chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 250 g pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Tarzan's Grip Grip for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Tarzan’s Grip Multi-Purpose General Adhesive 250 g has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Bonding fabric, leather, and rubber General craft builds Light repairs around the home Suitable surfaces The adhesive works well on the following surface types when properly prepared: Leather and canvas Rubber trim Timber and some plastics Card and foam board Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of allow adhesive to tack before assembly as directed on pack. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Forms a tough, flexible bond after solvent evaporation and cure. Press parts together firmly for best adhesion. Temperature and environmental performance Keep away from flames and high heat during application. Once cured, it resists typical temperatures. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Use appropriate solvent on uncured adhesive, working in a ventilated space. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Replace cap after each use to reduce skinning. Store below 30 C. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$15.59
Make quick, mess free stick ups with Bostik Removable Glu Dots. These clear, pressure sensitive dots are perfect for posters, photos, cards, decorations and classroom or office displays. They bond instantly, then peel away cleanly from most non porous surfaces when it is time to change things up. Why you will love them Clear and discreet for a neat finish Instant grab with no drying time Removable from most non porous surfaces No liquid spills or smears Great for home, school, office and events Best for Mounting photos, posters and signage Craft projects and scrapbooking Party decorations and displays Temporary fixes on glass, metal, plastic and sealed wood How to use Ensure surfaces are clean, dry and free of dust or grease. Peel a dot from the liner and place it on the item to be mounted. Press firmly, then position the item and press again for a secure hold. To remove, slowly peel the item away. Roll any remaining dot off the surface with your thumb. Good to know Test on a small hidden area first, especially on delicate or recently painted surfaces. Not recommended on flocked or fibrous wallpapers, unfinished timber or porous paint. Heat, UV and surface condition can affect removability. Product details Brand Bostik Product Removable Glu Dots Colour Clear Pieces 64 dots Bond type Removable, pressure sensitive Clean up Peel off and roll away residue
$7.00
Bring Your Leather Items Back to Life Restore your favourite leather goods such as shoes, belts, bags, and upholstery with confidence using Bostik Leather Repair Glue. This precision adhesive delivers a strong, flexible, and water-resistant bond that dries crystal clear. Key Features Ultra strong and long lasting bond for real and imitation leather Flexible and clear finish with no visible residue Resistant to water and heat up to approximately 60 °C Precision application through fine nozzle squeeze tube Multi material versatility suitable for leather, PVC, felt, canvas, some plastics, wood, and metal How to Use Ensure surfaces are clean, dry, and free from dust, oil, or old adhesive residue. For leather surfaces, avoid applying to the shiny side to prevent marks. Apply a thin film of glue to one surface. For non porous materials, apply to both surfaces. Press the surfaces together firmly. The bond sets almost instantly and reaches full strength in about 24 hours. Replace the cap immediately after use to prevent the tube from drying out. Tips and Care For best adhesion, lightly roughen smooth or shiny surfaces with fine sandpaper before gluing. Avoid stressing the repair before full cure. To remove unwanted glue, use acetone or nail polish remover on a small hidden area first. Technical Specs and Safety Form: Clear solvent based polyurethane adhesive Heat resistance: up to approximately 60 °C Highly flammable. Keep away from heat, sparks, and flame. Always follow manufacturer instructions and safety guidance. Use in a well ventilated area, wear protective gloves, and avoid contact with skin or eyes. Packaging Size: 20 mL tube
$9.79
Liquid Nails Fast is a water-based, high-strength construction adhesive with fast grab and low odour. It has a thick, non-runny consistency and is ideal for adhering timbers and other porous construction materials. Once dry, it has a beige (light tan) finish. Uses Liquid Nails Fast has a high initial grab that reduces the need to support joins while the adhesive cures. The grab works best with porous surfaces. It bonds to a wide range of materials including MDF, particle board, timber, plasterboard, styrene foam, masonry, concrete, tiles, ceramics, metals, plastics*, rubber and glass. Faster results occur when at least one surface is porous. Typical applications include: Areas where nailing is not desirable Skirting boards, architraves, and cornices Wall panelling to masonry Styrene foam to metal roofing Technical Features Fast grab – high initial holding reduces slippage on vertical surfaces Complies with AS 2329-1999 (Mastic adhesives for fixing wall boards) Non-drip formula – does not sag or string between panels Bridges gaps and adheres to uneven surfaces Low mess – excess can be wiped away with a damp cloth No solvent fumes – ideal for indoor projects Flexible – withstands thermal movement and vibration Heat resistant – maintains bond strength under sunlight Paintable when dry Easy to extrude in all temperatures Application Tips Use in conjunction with permanent mechanical fasteners except for low-stress applications such as wall panelling or lightweight fixtures. Bonds are not water resistant – protect from water if used outdoors. Drying time is extended in cold or damp conditions and with non-porous materials. Thicker layers take longer to dry. Test plastics before use – adheres well to UPVC but not to polyethylene or polypropylene. For wood flooring, use solvent-based Liquid Nails instead. Satisfactory for fixing sheet flooring to joists with the manufacturer’s minimum nailing specification, but not recommended for bonding sheet flooring to existing or concrete floors. Technical Details & Performance Good bond strength after 24 hours on porous substrates; continues strengthening over 2–3 days. Appearance: Smooth beige paste, free from lumps and air bubbles Specific Gravity: Approx. 1.44 g/mL @ 25°C Viscosity: 7000–9000 Poise Slump: 0 mm (typical) Shear Adhesion Strength (7 days, AS2329): >1500 kPa (Hoop pine substrate) Peel Adhesion Strength (7 days cure): 40 N/25 mm (variant to AS2329) Initial Bond Strength (24 hrs): >200 kPa Heat Resistance: Withstands up to 140°C temporarily. Constant high temperatures may reduce load-holding power. Creep Resistance (under constant load):– At 80°C: holds 500 g (7.8 kPa) on 625 mm² bond area– At 25°C: holds 6 kg (100 kPa) on 625 mm² bond area Coverage Approximately 15 metres of a 5 mm diameter bead. Curing time increases with thicker bonds or larger bond areas. Data provided is indicative only and not for design use. Cleaning Clean with hot soapy water or a damp cloth while wet. Once dry, remove by scraping or peeling. *Always pre-test plastics for adhesion suitability.
$25.37
Earl’s Powder Putty – Mix-to-Use Interior & Exterior Filler Earl’s Powder Putty is a multi-purpose powder filler for professional and DIY repairs. Just add water, mix only what you need, and achieve a tough, easy-sand finish with no waste and no shrinking. Brand: Earl’s Interior and exterior use* Mix-on-demand convenience Non-shrinking, smooth finish Easy sanding and shaping Indefinite shelf life in dry powder form Proudly made in Australia *Exterior applications must be sealed/painted and used on stable substrates. About Earl’s Powder Putty Earl’s Powder Putty delivers reliable, high-quality filling for timber, walls, masonry and metal. Because it’s supplied as a dry powder, you can tailor the mix to your task—stiffer for knife-grade filling and sculpting, or looser for fine skim work. The result is a hardwearing repair that sands easily and accepts coatings beautifully. Where Earl’s Powder Putty Works Timber & woodwork: doors, frames, skirting, architraves, furniture, cabinetry Walls & panels: plasterboard and cement sheeting patching and feathering Masonry & concrete: chips, small holes and surface imperfections Metals: minor dents and irregularities prior to priming and painting Floor preparation: quick patching of distressed boards prior to covering Craft & hobby: architectural details, mouldings and small sculpting tasks Why Choose Earl’s No shrink: Formulated to dry without shrinking for flush, invisible repairs. Mix what you need: Reduce waste and always work with a fresh batch. Shapes perfectly: Once dry, Earl’s Powder Putty can be cut, carved, sanded or sawn. Paint-ready: Accepts primers and topcoats after proper dry and prep. Economical & dependable: Indefinite shelf life in powder form when stored dry. Directions for Earl’s Powder Putty Surface prep: Ensure the area is clean, dry and sound. Remove loose material, dust, grease and contaminants. Key glossy surfaces for better adhesion. Mix: In a clean container, add Earl’s Powder Putty and slowly incorporate clean water. Stir to a smooth, lump-free paste. Adjust water to suit the task. Apply: Press the mix firmly into the repair with a putty knife or trowel. Slightly overfill to allow for sanding back flush. Build: For deep repairs, apply in layers, allowing each to firm before adding the next. Finish: Once dry, sand smooth. The cured filler can be carved or sawn to refine edges and profiles. Coat: Prime/seal and paint after full dry. For exterior use, always seal with suitable coatings. Clean-up: Clean tools with water while the product is still wet. Dry and recoat times vary with temperature, humidity and film thickness. Allow extra time in cool or damp conditions and for deep fills. Good to Know About Earl’s Not waterproof by itself: Water and weather resistance requires sealing/painting. Not flexible: Avoid use where movement, vibration or structural flexing is expected. Stable substrates only: Ensure exterior bases are sound and well prepared. Storage: Keep Earl’s Powder Putty dry and tightly closed. Moisture exposure can reduce performance after opening. Safety: Avoid dust during mixing and sanding. Use PPE and adequate ventilation. Typical Earl’s Applications Filling nail and screw holes, chips and minor cracks Skim patching and feathering edges prior to painting Rebuilding small decorative profiles and mouldings Levelling minor surface imperfections before finishing Specifications Brand Earl’s Product Name Earl’s Powder Putty Product Type Multi-purpose powder filler Format Dry powder; mix with clean water Colour (dry) Off-white to white; paintable Use Areas Interior and exterior* (exterior must be sealed/painted; stable substrates only) Substrate Compatibility Wood, plasterboard, cement sheeting, concrete, masonry, properly prepared metal Shrinkage Non-shrinking when used as directed Sandability Easy sanding once fully dry Paintability Prime/seal and paint after full dry Water Resistance Requires sealing; product itself is not waterproof Shelf Life (powder) Indefinite when stored cool, dry and sealed Clean-up Water while wet Tools Putty knife, trowel, mixing stick or paddle, sanding block Country of Origin Australia Limitations of Earl’s Powder Putty Do not use as a flexible gap filler or where structural movement is expected. Always prime/seal before exposure to moisture or exterior weather. Deep repairs may require multiple layers with adequate drying between coats. Not for permanently wet, submerged or high-movement joints. FAQs – Earl’s Powder Putty Can I mix a large batch and store it?Mix only what you can use within the working time. Discard any mix that begins to stiffen or set. Can I screw or nail into it?For non-structural tasks, light fixings may be possible in sufficiently thick, fully cured areas. Pre-drill as needed and test first. Is it paintable?Yes. Once dry and sanded, prime or seal the repair and finish with your chosen coating system. Always follow label directions. Test on a small, inconspicuous area to confirm compatibility and finish.
$10.50 - $175.00
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$9.70
USE TRICLEANIUM: •Before painting or wallpapering •On internal or external walls, floors, bench tops, tiles, slate, stainless steel, baths, glass, stove tops, range hoods, fridges, cupboards, shelves, greasy oven trays, home brewing equipment. •To clean musty washing machines •Outside on greasy driveways or garage floors, boats or BBQ's. •In the factory, commercial kitchen, where concentrated cleaning power or degreasing is needed. TRICLEANIUM is a wholly Australian owned family business and has been in the market place for more than 50 years. TRICLEANIUM is a concentrated cleaning product in crystal form (100% alkaline salts). It is not diluted by fillers or water. TRICLEANIUM’s ultra concentrated power means it can tackle the toughest jobs that other products won’t touch including BBQs, range hoods, greasy driveways, cleaning in engineering works and the like. TRICLEANIUM can be used on almost any washable surface (floors, walls, concrete, kitchen appliances, fibreglass, tiles etc) but prolonged contact with exposed aluminium and brass should be avoided.
$28.21
SikaBond® -TechGrip is a high strength multipurpose, polyurethane glue that provides a super strong bond to almost any substrate and is ideal for woodworking and project work. Uses SikaBond® -TechGrip can be used on most substrates due to its excellent adhesion. These include: Wood Stone Metals Glass Ceramics Concrete Brick Masonry Advantages Waterproof Resistant to solvents and chemicals Paintable with water based and solvent based paints High adhesion strength Storage and Shelf Life Store in a cool, dry place with 25C maximum condition. This material will keep for at least twelve (12) months. Instructions for Use Surface Preparation Ensure all surfaces are clean, dry, oil and dust free and that one surface is porous. (SikaBond® -TechGrip works best when both surfaces are porous). Application Apply sparingly to one surface and bring surfaces together within 15 minutes. Secure/clamp for 3-4 hours. Wipe excess away with a cloth to limit sanding after cure. Allow 24 hours for full cure. As glue will foam a little while curing, wipe off excess with a cloth to limit sanding and painting. Slightly dampen dry timber surfaces to improve bond and accelerate cure. Cleaning Wipe nozzle and cap of bottle after use and dispose of any unused material in accordance with local authority regulations. Colour: Brown Density 1.11 kg/litre approx. Bond Strength Tensile Strength - 3030kpa Test Substrate - Timber: End grain to end grain Viscosity 6,000cps Handling Precautions Avoid contact with skin and eyes. Wear protective gloves and eye protection during work. If skin contact occurs, wash skin thoroughly. If in eyes, hold eyes open, flood with warm water, seek medical attention without delay. A full Material Safety Data sheet is available from Sika on request.
$24.20
Selleys Original Sugar Soap is a powerful liquid household cleaner which is effective in removing grease, grime and dirt from household surfaces. It can be diluted with water or used neat. Also recommended for cleaning surfaces prior to painting and wallpapering. Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Features Concentrated – makes up to 30 litres Professional strength grease & grime cleaner Safe for all modern washable surfaces including walls, floors, tiled and laminated surfaces. Can be diluted with water or used neat Where can this product be used? Kitchen surfaces – to clean floors, walls and cupboards Bathroom & Laundry surfaces – to clean bathtubs, showers, sinks, toilet bowls and tiled surfaces Painting & Wallpapering – wash surfaces prior to painting General Cleaning – appliances, stainless steel, blinds and more What materials is this product suitable for? Floors Tiles Walls Benchtops Cooktops Appliances Wipe off immediately from aluminium and brass surfaces Handy tips Dilute to suit the cleaning task. Liquid Sugar Soap, as a phosphate-based cleaner, can be used as part of lead residue abatement after lead paint removal. Consult the relevant authorities on regulations, requirements and approvals prior to use for this purpose. For smaller areas or spot, cleaning try Selleys Super Kleen Safety tips For stubborn, in-ground stains use neat with a safe scouring cloth – a Selleys Wash Up Wiz is ideal. Avoid contact with skin and eyes. If in eyes, flood with water for 15 minutes. The use of rubber gloves is recommended If swallowed, give a glass of water and see a doctor. If in eyes, wash out immediately with water For advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctor. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site.
$8.50
![Selleys No More Gaps Bricks Mortar [Charcoal]](http://gluesaustralia.com.au/cdn/shop/files/9300697130310_c74acc80-87eb-4da9-9a5a-2847d2d610ab.png?v=1754711847&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$24.79
![Selleys No More Gaps Bricks & Mortar x 440g [Terracota]](http://gluesaustralia.com.au/cdn/shop/files/81ee53b7eade4c22a1268e1a28879d4e.jpg?v=1757753123&width=645)
Selleys No More Gaps Bricks and Mortar is a textured, ready to use weather-resistant gap filler available in a range of colours to match your existing mortar. It's mortar like texture allows easy repair of unsightly cracks and gaps in brickwork around the home. Features Ready mixed mortar filler, so is quick and easy to apply with a caulking gun. Has a mortar like texture for a textured finish and match to cement mortar and render. Is more flexible than mortar which will help prevent more damage to the mortar Is weather and UV resistant with a UV stable formula to prevent colour deterioration. Provides a more suitable finish on rendered walls than smooth fillers. Contains a fungicide and algaecide to protect against unsightly mould and algae growth. Has superior adhesion to a broad range of surfaces, making it easy to use. Will not stain building materials Can be painted over with both water and oil based paints, after the surface has skinned. (Approximately 2 hours after application). Is water based, so can be cleaned up with water easily. Is sandable when dry for a rough or smooth finish. Where can this product be used? Repairing cracks and gaps in brickwork and/or cement blocks where mortar has fallen out or eroded. Stationary cracks in pathways. Sealing gaps around windows or between brick wall and roof eaves. Repairing stationary cracks in cement render. Repairing penetration holes around pipe work, ducting, etc. Sealing gaps where mortar has fallen out in ridge capping on tile roofs. What materials is this product suitable for? Brick Concrete Render Fibre cement sheeting Laminated plastics Hardboards Aluminium Ceramics Timber How to Use Ensure the surface is clean, dry and free from dust, grease, flaking/powdery paint and old or crumbling caulk. Cut cartridge tip, fit nozzle and cut to desired opening (5mm) then insert into caulking gun. We recommend Selleys Light Speed Caulking Gun. Apply using caulking gun. Apply with caulking gun, forcing product into gap. Press into cracks and holes using a spatula or wet finger. Clean away excess from surfaces immediately using a damp cloth. For larger cracks & holes, 2 applications may be necessary. Allow first application to dry before applying second. Hardens in 24 hours depending on weather. Protect from rain until firmly skinned. Limitations: Not suitable for areas of continuous water immersion. Not suitable as a substitute for mortar in construction as it does not have the structural properties of mortar. Not suitable for moving cracks. Do not use or store below 5°C. Handy Tips For the best results slightly dampen the surface prior to application. For use in fine cracks, eg. in cement render rub Selleys No More Gaps Bricks and Mortar into cracks or use Selleys No More Cracks Exterior & Brick Render. If painting over the product, apply undercoat before applying a top coat for the best results. Keep a pack of Selleys Sugar Soap Wipes handy to wipe up any spills and for cleaning. They are an easy and effective way to keep clean on the job.
$28.08
Selleys KwikGrip Spray 150g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 150g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$13.73
Crystal clear Can be used even on damp/wet and impervious surfaces. Closest you will get to a transparent Ritetack 290ml tube Used indoors and outdoors as long as not exposed to UV. Clear adhesive Invisifix is a versatile 290ml tube of clear construction adhesive that lets you see exactly what you’re gluing. A quick, easy-to-use, water-friendly clear construction adhesive allows you to see exactly what you’re gluing. Reasons why to use Invisifix The excess clear construction adhesive always finds a way to make itself noticeable. Sometimes it is even difficult to remove it. With Invisifix, you don’t have to worry about unaesthetic colours since it is literally see-through! Amazing fast grab! That means no time wasted holding things into place while you wait for them to adhere. With Invisifix, you apply it to the surface, and it immediately sticks! Invisifix is water-friendly, so no more breaking a sweat while trying to dry surfaces before applying. This comes in handy if you’re thinking of applying Invisifix Clear Adhesive in areas prone to humidity and dampness, like bathrooms, pool areas, or kitchens. This adhesive can stretch up to 375% from its original size, and that’s important if you want some flexibility in your adhesion. That means that sudden movements like some impact won’t compromise the integrity of your adhesive and of whatever it is holding. Not only does Invisifix work on virtually any surface, but it also won’t stain any of them, including the porous ones, like a stone!
$9.95
PREP Multi-Use adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesives, PREP offers multiple solutions in one bottle. PREP Multi-Use adhesive will glue almost anything to anything Features and Benefits: Environmentally friendly Non-toxic Dries quickly – dries clear Non-flammable High water resistance Prep MultiUse Adhesive is a styrene-based all-purpose adhesive, originally designed to replace PVA adhesives. Unlike conventional adhesive, Prep offers multiple solutions in one bottle. Prep Multi-Use Adhesive will bond almost anything to anything. Bond strength is greatest on porous surfaces such as timber, fabric, leather, paper, styrene foam, metal, wood and glass, even concrete, plaster, and fibro. Prep MultiUse Adhesiveis also a suitable adhesive for non-porous surfaces such as steel, aluminum, brass, copper, ceramics, and glass. It will not re-emulsify nor dissolve if subject to water after drying like PVA’s. Prep MultiUse Adhesiveis a thicker emulsion than PVA’s so it doesn’t drip on vertical surfaces. It has greater bond strength on most surfaces. Prep MultiUse Adhesivemay also be diluted, for use as a ‘dust sealer or primer/sealer’ for concrete and masonry surfaces. It may be used diluted as a bonding agent between layers of concrete or in the mix.
$11.52
Prep Indoor Furniture Wood Polish is a naturally formulated polish designed to restore, protect and beautify indoor timber surfaces. It covers light scratches, lifts stains and renews the natural richness of wood with a transparent matt finish. Uses Nourishes, restores and protects indoor furniture and woodwork Conceals minor scratches and blemishes Removes stains and dull patches Helps preserve timber surfaces from everyday wear Product Details Size / Packaging 500 mL bottle Coverage Up to 20 m² per litre Application Method Mist on and wipe in with a clean rag Number of Coats 1 coat Recoat Time After 24 hours Finish Transparent matt How to Apply Shake the bottle well before use. Mist the product lightly onto the timber surface. Wipe it in using a clean, soft rag until evenly spread. Let it cure for 24 hours before applying any further coats or placing items back. Why Choose Prep Indoor Furniture Wood Polish This polish is ideal for those seeking a gentle but effective wood restore solution for their indoor furniture. Its natural formulation ensures it is kind to timber while delivering visible results, improved colour, refreshed surface, and protection from everyday wear.
$18.00 $12.95
A durable, multi-purpose filler that has been designed for filling deep and wide cracks and holes on all surfaces inside and outside the home. Easy to sand, sets to a super hard finish and is highly crack resistant. Filling blade included For use on: Brick, masonary, concrete, plasterboard, wood & metal (INTERIOR & EXTERIOR) Fill depth: Up to 10mm Dries in: 3 hours Ready to use: YES Colour: White Application • Surface to be filled should be clean and dry with no loose or powdery material. • Exterior surfaces and metals (eg. nail heads) should be primed before application. • Using the attached filling blade press filler in firmly and remove excess. • Allow to dry (2-3 hours in thin 2-3mm applications depending on humidity). Allow longer drying times if painting with oil based paints (24 hours minimum) or for deeper applications. • For deeper jobs apply in 10mm layers, allowing each layer to set, before applying the next layer. • Protect from rain until painted over. .• For best results, apply paint undercoat before applying water or oil based paint top coat. • Use Polyfilla Gap filler or silicone sealant where joint movement occurs. • Clean up with water before filler dries FAQ's Q. Is there a filler I can use for both inside and outside? A. Polyfilla Large Cracks is a multipurpose filler designed for filling cracks and holes on all surfaces inside and outside the home.
$20.99
PC-Fahrenheit™ Putty Epoxy is the choice for temperatures up to 260° C. It is supplied as a premeasured stick that you mix with fingers. Fast curing (60 min). Best for steam heat applications. A toolbox must. Great on copper and iron. Here are just a few specific uses (there are hundreds of other uses): Seal cracked steam or hot water radiator Stop leaking steam fittings Fill hole in heat exchanger Attach thermocouple to hot surface Seal chimney ductwork How to prepare a surface for bonding with PC-Fahrenheit™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. A mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Fahrenheit™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Fahrenheit™ repair a leaking steam radiator? PC-Fahrenheit™ resists higher temperatures and is suitable for repairing steam pipes and radiators. Can PC-Fahrenheit™ be used in a fireplace or wood burning stove? PC-Fahrenheit™ will withstand temperatures up to 260°C. A fireplace or wood burning stove creates temperatures exceeding 260°C. Can PC-Fahrenheit™ be used to seal heater chimney duct? PC-Fahrenheit™ is excellent for use on sheet metal and the temperature is within an acceptable range. Can PC-Fahrenheit™ seal a rust hole in barbecue grill? PC-Fahrenheit™ can be used on the barbecue grill exterior but is not recommended for the interior. How long should PC-Fahrenheit™ be mixed before applying? Mix PC-Fahrenheit™ for 45 to 60 seconds then immediately apply. What is the temperature limit? PC-Fahrenheit is not intended to exceed 260°C. - Will PC-Fahrenheit™ burn? PC-Fahrenheit™ is not flame resistant and may burn if exposed to direct flame. Does PC-Fahrenheit™ stick to car radiator? Car radiators are made of various metals and plastic composites. Test for adhesion and test for leaks.
$16.17
Parfix PVA is a PVA based adhesive suitable for general interior woodworking joinery and other craft uses. It is non-toxic, will not stain timber and dries clear. High strength Clear drying Water clean up
$19.67
Highly flexible as well as mould and UV resistant, Parfix All Purpose Silicone is suitable for use on shower screens, metal roofing, concrete and gutters. Highly flexible Mould and UV resistant Neutral cure Non-corrosive
$10.20
The Monarch Mini Skeleton caulking gun is a smaller size caulking gun matched to the range of Monarch Mini sealant cartridges. This compact design provides easier access to tight spaces where conventional size guns find difficult. Featuring an inbuilt cartridge opener, the mini caulking gun can open a cartridge safely without using a knife for quick & easy use.
$7.20
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 32m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600356N_25b0d34f-62b0-49f4-86cb-a6535eeabdae.jpg?v=1754712481&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$27.91
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$29.94
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$9.16
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very Strong, durable bonding Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua) Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Heat Resistant Clamping is recommended to achieve a stronger bond Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 80°C but strength is regained when temperature drops Where can this product be used? Load bearing repairs Gluing the head back on your hammer Fixing loose table or chair legs. Bonding solid pieces of Aluminium sheeting Bonding timber on your boat Repairing splits and cracks in Cricket bats Bonding fibreglass sheets Repairing Ski’s Fixing Dynabolts and metal rods into concrete What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics Crystal Leather How to use this product Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately. When using tubes, Ensure correct caps are replaced on each tube or they will harden Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$29.36
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$9.00
Give your home a crisp eucalyptus lift with this antibacterial air and surface freshener from Glitz. It tackles everyday odours, leaves a clean eucalyptus scent, and is suitable for quick freshen ups in bathrooms, kitchens, bins, pet areas, and cars. Why you'll like it Antibacterial formula for hygienic freshening of hard, non porous surfaces Clean eucalyptus fragrance that smells fresh without being overpowering Fast acting spray ideal for busy households and shared spaces Versatile use in bathrooms, toilets, bins, shoes, gym bags, and vehicles Convenient 200 g aerosol that fits easily in cupboards and glove boxes Where to use Air freshening in bathrooms, laundries, living rooms, and entryways Hard, non porous surfaces such as benches, sinks, tiles, bins, door handles Cars, caravans, and small spaces that need a quick refresh How to use Shake can well before each use. For air freshening: hold can upright and spray into the center of the room for a few seconds. Allow mist to disperse. For surfaces: spray from 20 to 25 cm away onto hard, non porous surfaces until lightly covered. Spread with a clean cloth and allow to air dry. For food contact areas rinse with potable water after use. Repeat as needed. Always test on a small inconspicuous area first. Good to know Do not use on fabrics, leather, or polished wood Not for personal hygiene or use on skin Use only as directed in a well ventilated area Specifications Brand Glitz Product Antibacterial Eucalyptus Spray Fresh Air Cleaner Net Weight 200 g Format Aerosol spray Fragrance Eucalyptus Suitable Surfaces Hard, non porous household surfaces Country of Use Australia Safety Flammable aerosol. Pressurised container. Keep away from heat, hot surfaces, sparks, open flames, and ignition sources. No smoking. Do not pierce or burn, even after use. Protect from sunlight and do not expose to temperatures exceeding 50°C. Avoid breathing spray. Use in a well ventilated area. If in eyes rinse with water. If irritation persists seek medical advice. Keep out of reach of children and pets. Frequently asked questions Can I use it on fabric or carpetsIt is designed for air freshening and hard, non porous surfaces. For fabrics test a hidden area first. Prolonged wetting may mark textiles. Does it remove strong bin and pet odoursYes, it helps neutralise common household odours and leaves a fresh eucalyptus scent. For persistent odours clean the source before spraying. Is it safe for kitchensYou can use it on hard kitchen surfaces. Rinse food contact areas with potable water after treatment. Shipping and returns Ships Australia wide from our Victorian warehouse Aerosols travel by road only. Express options may be limited Change of mind returns accepted within our store policy when unopened and in resalable condition Tip: Pair with bin liners and cleaning vinegar for a simple fresh home routine.
$8.71 $7.25
Keep your kitchen surfaces looking new with a daily cleaner made for modern stone and composite benchtops. This formula lifts grease, fingerprints, and food residue while restoring a natural looking shine. Streak free. No sticky film. Fast to spray, wipe, and finish. Why you will love it Safe for sealed stone surfaces including engineered stone, granite, marble, and quartz Streak free finish that helps reduce dulling and haze Everyday formula that cuts through cooking oils and spills Helps maintain the protective seal of correctly sealed surfaces Low odour for comfortable use in kitchens and living areas Best for Kitchen benchtops and splashbacks Island benches and breakfast bars Polished stone tables and sideboards Bathroom stone vanities and shelves How to use Remove loose crumbs and grit with a dry cloth. Spray a light, even mist over the surface. Wipe with a clean microfibre cloth in overlapping passes. Flip to a dry side and buff to a natural, even shine. Pro tips For heavy spots, leave the spray on the mark for 30 to 60 seconds before wiping. Use a dedicated microfibre cloth for stone to avoid cross contamination. Maintain your benchtop seal as recommended by the surface supplier. Surface compatibility Safe on Not suitable for Sealed engineered stone, sealed granite, sealed marble, sealed quartz, porcelain, ceramic tiles, laminate Unsealed stone, sandstone, limestone, unfinished concrete, waxed or oil finished surfaces Good to know Everyday use. Gentle on properly sealed stone finishes. Leaves a fresh, clean scent that does not linger. Designed to clean. Not a stain remover or etch repair product. Frequently asked questions Can I use it on marbleYes, if the marble is correctly sealed. Always test in a hidden spot first. Is it suitable for food preparation areasYes. Clean the surface, then allow to dry before placing food directly on the benchtop. Will it remove etching or dull spotsNo. Etching is a surface damage issue. Seek professional polishing for that type of repair. How often should I use itUse daily or as needed to keep the surface free of residue and fingerprints. Specifications Finish Streak free, natural looking shine Suitable surfaces Sealed stone and composite benchtops Fragrance Light and fresh Use frequency Daily or as required Application method Spray and wipe with microfibre cloth Safety Read and follow the label directions. Test on a small hidden area before first use. Keep out of reach of children and pets. Do not use on unsealed or acid sensitive stone. Why buy from Glues Australia Curated range for Australian homes and trades Fast dispatch from our local warehouse Helpful support if you need product guidance
$9.91 $8.10
Glitz Leather Cleaner Restores and Protects Leather 500ml Bring tired leather back to life with Glitz Leather Cleaner. This easy to use spray lifts dirt, body oils, and everyday grime while nourishing the surface to help keep leather soft and supple. Ideal for lounge suites, car interiors, handbags, jackets, and more. Why you will love it Clean and condition in one step to refresh appearance and feel. Helps protect against drying and cracking with regular use. Fast acting formula wipes away residue for a low sheen finish. Versatile for most finished leather surfaces at home, in the car, or at work. Convenient 500ml size for multiple cleaning sessions. Best for Finished leather lounges and armchairs Automotive leather seats and trim Leather bags, wallets, belts, and jackets Office chairs and commercial seating Not suitable for Suede, nubuck, aniline, unfinished or highly porous leather Alcantara, fabric, or vinyl Severely cracked or peeling coatings How to use Vacuum or dust the surface to remove loose particles. Shake well. Apply a light, even spray to a clean, soft cloth. Do not saturate. Work in small sections, gently massaging the leather with circular motions. Wipe away lifted soil with a second dry cloth. Buff lightly to a natural low sheen. Repeat on heavy buildup if required. Patch test first in a hidden area for colour fastness and finish compatibility. Care tips Clean monthly on high use items or every 2 to 3 months on lightly used pieces. Keep leather out of direct sunlight where possible to reduce fading. For long term protection, follow with a dedicated leather conditioner as needed. Product details Brand Glitz Product type Leather cleaner and maintainer Finish Natural low sheen Size 500ml Application method Spray onto cloth and wipe Suitable surfaces Most finished leather furniture and automotive leather Safety and storage Use in a well ventilated area. Avoid contact with eyes and prolonged skin contact. Keep out of reach of children and pets. Store upright in a cool, dry place. Do not freeze. Frequently asked questions Will this make leather shinyIt restores a natural low sheen. For a glossy look use a leather polish after cleaning. Can I spray directly onto the seatFor best control apply to a cloth first, then wipe the leather. Is it safe for perforated automotive leatherYes when applied to a cloth and used sparingly. Do not flood perforations. Good to know Regular light cleaning keeps leather looking newer for longer. Always remove abrasive grit before wiping to avoid micro scratching.
$20.47 $19.19
Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Make light work of dishes with a refreshing lemon clean. Glitz Citrus Dishwashing Liquid delivers rich suds that lift grease and food residues fast, leaving plates, glasses, and cookware spotless with a fresh citrus finish. The generous 5L bulk pack is ideal for busy family homes, offices, cafes, and community kitchens that want reliable performance and great value. Why you will love it Powerful everyday clean that breaks down oils and baked on residues Fresh lemon fragrance for a just cleaned scent Stable foam for longer sink time and fewer top ups Rinses easily to help reduce spotting and streaks Cost effective 5L format for regular high volume washing Versatile for hand washing dishes, cutlery, glassware, and cookware Best for Daily sink loads at home or in shared kitchens Cafes, lunchrooms, clubs, and community events Rental properties and short stay turnovers How to use Fill sink with warm water. Add dishwashing liquid. Start with 1 to 2 teaspoons per 5L of water for light to normal soils. Increase for heavy grease. Wash using a sponge or brush. Soak stubborn items for a few minutes. Rinse thoroughly with clean water and allow to air dry or towel dry. Tips For glassware, use hot water and a soft sponge to help prevent water spots. Change solution when suds begin to collapse or water appears cloudy. Do not use in automatic dishwashers. This formula is for manual washing. Product details Brand Glitz Product Citrus Dishwashing Liquid Fragrance Fresh Lemon Format Liquid Size 5L Use Manual dishwashing and general sink cleaning Suitable surfaces Dishes, cutlery, glassware, ceramics, stainless steel cookware Country of use Australia What is in the box 1 x Glitz Citrus Dishwashing Liquid Fresh Lemon Clean 5L Storage and safety Store upright in a cool, dry place away from direct sunlight. Keep out of reach of children and pets. Avoid contact with eyes. If product gets in eyes rinse with water. If irritation occurs discontinue use. Sustainability note Use the recommended dose to minimise waste and water use. Recycle the container where local facilities allow. Frequently asked Can I use it on non stick cookware Yes, use a soft sponge and follow the cookware care instructions. Is it safe for septic systems This hand dishwashing liquid is designed for general household use. As with any cleaner, use as directed and follow local guidance for septic systems.
$25.86 $24.30
Glitz Glass Cleaner for Crystal Clear Surfaces Give windows, mirrors, and glass splashbacks a streak free shine with Glitz Glass Cleaner. This fast drying spray cuts through fingerprints, water spots, and everyday grime so you can enjoy a spotless, crystal clear finish in seconds. Why you will love it Streak free clarity for windows, mirrors, and glass doors Fast acting formula lifts fingerprints and smudges Quick drying finish helps resist new marks Ideal for stainless trims, ceramic cooktops, and glossy tiles test first Fresh, clean scent that leaves surfaces looking like new Where to use Windows, mirrors, shower screens, glass tables Car and caravan interior glass use sparingly on tinted film and test in a small area first Kitchen splashbacks and glossy surfaces not suitable for unfinished stone or porous surfaces How to use Spray a light, even mist onto the surface. Wipe immediately with a clean, lint free cloth or paper towel. For best results, finish with a dry microfiber cloth using circular motions. For heavy build up, repeat the application as needed. Pro tips Work out of direct sunlight to reduce rapid evaporation. Use one cloth to clean and a second dry cloth to buff for a showroom shine. Replace cloths when damp to avoid streaks. Key details Surface type Glass, mirror, glazed ceramic, glossy tiles Finish Clear, streak free Use Household, office, automotive interior glass Fragrance Fresh clean scent Application Spray and wipe Good to know Always test on an inconspicuous area before full use. Do not use on unsealed stone or porous surfaces. Keep out of reach of children. Avoid contact with eyes. Store upright in a cool, dry place with the cap closed. What is in the box 1 x Glitz Glass Cleaner FAQs Will it leave streaksUsed with a clean, dry microfiber cloth, the finish is clear and streak free. Can I use it on tinted windowsTest first on a small area of the film. Apply to the cloth, not directly to the film, and wipe gently.
$27.01 $23.09
Glitz Hand Wash Gentle Moisturising Formula 5L Keep hands fresh and cared for with Glitz Hand Wash Gentle Moisturising Formula. This generous 5 litre refill is perfect for homes, offices, gyms, schools, hospitality venues, and anywhere high hand hygiene is essential. The balanced formula cleans effectively while helping to maintain the skin’s natural moisture. Why you will love it Gentle everyday clean that is kind to skin Moisturising formula that helps prevent dryness with frequent washing Rich lather that rinses quickly to leave hands feeling soft Light, pleasant fragrance suitable for shared spaces Economical 5L size for easy refills and reduced plastic waste Ideal for liquid soap dispensers and pump bottles Best for High traffic bathrooms and kitchens Reception areas, classrooms, healthcare waiting rooms, warehouses, and workshops Refilling counter top and wall mounted dispensers How to use Decant into a clean, dry dispenser or pump bottle. Wet hands with clean water and apply one pump of hand wash. Rub palms, backs of hands, between fingers, and around thumbs for at least 20 seconds. Rinse thoroughly and dry with a clean towel or paper towel. Good to know Suitable for frequent use on most skin types Clear liquid designed to minimise dispenser staining Bulk size helps lower cost per refill Product details Brand Glitz Product Hand Wash Gentle Moisturising Formula Format Liquid hand wash Size 5 litres Use Everyday hand washing and dispenser refills Fragrance Light, fresh Colour Clear or lightly tinted Storage and shelf life Store upright in a cool, dry place away from direct sunlight Keep tightly closed between refills Safety For external use only Avoid contact with eyes. If contact occurs, rinse with water Keep out of reach of children Sustainability tips Refill existing pumps and dispensers to reduce plastic waste Rinse and recycle the bottle where local facilities allow
$36.87 $35.56
Gorilla Black Mounting Tape delivers a fast, permanent bond for indoor projects. This industrial strength double sided tape grips to a wide range of smooth and lightly textured surfaces, helping you mount, fix, and build without screws or nails. Why you will love it Strong indoor hold with permanent bond Double sided for clean, hidden mounting Works on smooth and lightly textured surfaces Easy, tool free application Weather resistant carrier helps resist moisture and temperature changes indoors Great for Mounting hooks, signs, cable clips, and décor Fixing skirting trims and craft fixtures Securing powerboards and small organisers to walls or furniture DIY quick fixes where drilling is not an option Works on Metal, glass, finished wood, plastic, tiles, painted drywall, stone, and more. Not recommended on delicate, recently painted, dusty, oily, or damp surfaces. How to use Clean surfaces with isopropyl alcohol and let dry. Measure and cut the length you need. Press tape firmly onto the back of the object. Peel liner to expose the adhesive. Position once and press firmly for 30 to 60 seconds to activate the bond. Load gradually. Full bond strength develops after proper pressure and dwell time. Pro tips Use enough tape to support the weight of the item. As a guide, allow generous coverage across the mounting area. For painted surfaces, test in a small area first. Removal may damage paint. Avoid repositioning after contact. This reduces bond strength. Specifications Brand Gorilla Product type Double sided mounting tape Colour Black Length 3.04 m Use Indoor Bond Permanent Care and safety Keep out of reach of children. Do not use as a load bearing safety device. Store in a cool, dry place with liner intact.
$36.07 $27.45
Make BBQ clean up quick and simple with Selleys Tough Wipes. These oversized, dual action wipes lift grease and grime from hotplates, grills and accessories, then trap the mess so you can get back to cooking. The textured nodules help scrub through build up without scratching, while the smooth side polishes surfaces clean. Why you will love it Removes BBQ grease and grime fast Textured cleaning nodules to break up stubborn residue Safe for food contact surfaces when used as directed Use before or after you cook for a hygienically clean surface Large wipe size for better coverage Where to use BBQ plates, grills and racks BBQ hood and warming rack Rotisserie and wok burner components BBQ utensils and shelves Interior health grills and sandwich presses Public BBQs Good to know Wipe size: 250 mm x 275 mm Available in multiple pack sizes Impregnated wipe technology for effective cleaning How to use Open the resealable lid, peel back the sticker and pull out one wipe. Use with the nodule side down to scrub plates, grills and other dirty surfaces. No need to wipe dry. Heat the BBQ and start cooking once the surface is ready. Reseal the pack to keep remaining wipes fresh. Dispose of used wipe in the rubbish bin. Limitations Heavily carbonised residue should be scraped off first for best results. Pro tips One to two wipes usually clean a standard BBQ. Very large or very dirty BBQs may need more. Grease lifts more easily when the BBQ is slightly warm. Turn off heat and ensure it is cool enough to touch before cleaning. For tough baked on build up or periodic deep cleans, pair with a dedicated BBQ cleaner. Specifications Type Impregnated cleaning wipe Surface compatibility Most BBQ cooking surfaces and accessories. Always test on a small area first. Wipe size 250 mm x 275 mm Use locations Indoor and outdoor Pack sizes Varies by retailer What is in the box Selleys Tough Wipes in a resealable pack. Safety Read and follow the instructions on pack. Wash hands after use and keep out of reach of children.
$12.59
Adhesive holder designed to hang standard trigger spray bottles securely. Space-saving vertical storage Water resistant No drilling required Examples of use: Hold glass cleaner in the kitchen Store disinfectant in the laundry Keep garden sprays in the shed
$7.88
Reliable adhesive hanging solution for tidy, damage-free organising. Installs in minutes without tools Removes cleanly from most painted walls Use indoors on smooth surfaces Examples of use: Organise entryways and kitchens Hang decor for events Add storage in bathrooms and offices
$5.24
Wall-mounted hanger to air, dry or stage outfits without drilling. Folds when not in use Strong adhesive backing Great for laundries and wardrobes Examples of use: Hang shirts after ironing Air-dry gym gear Stage school uniforms overnight
$18.86
Adhesive holders to support lightweight curtain rods on smooth walls. Tool-free install Damage-free removal Fits slim curtain poles Examples of use: Mount sheer curtains in rentals Create a cafe curtain over a sink Add a rod to a study nook
$14.77
Ryobi ONE+ 18V Dual Temperature Hot Glue Gun – Tool Only delivers precise and consistent adhesive application for DIY, craft, and repair projects. Designed for versatility, it features dual temperature control and cordless convenience, making it ideal for home and professional use. Key Features Dual temperature settings: Choose between 120°C for delicate materials and 160°C for stronger bonding applications. Fast heat-up time: Ready to use in approximately 3 minutes for quick, efficient work. Long nozzle design: Provides greater reach and precision when gluing hard-to-access areas. Drip tray and ergonomic handle: Keeps your workspace clean and provides comfort during extended use. LED indicator: Red light shows warming up, green light indicates ready-to-use. Part of the Ryobi ONE+ system: Compatible with all Ryobi 18V ONE+ batteries (sold separately). Specifications Voltage: 18V High Temperature Mode: 160°C Low Temperature Mode: 120°C Glue Stick Diameter: 11–12 mm Nozzle Hole: 3.0 mm Heat-Up Time: Approx. 3 minutes Weight (without battery): 0.4 kg Included Ryobi ONE+ 18V Dual Temperature Glue Gun (Tool Only) User Manual Compatible Batteries (Sold Separately) RB18L13, RB18L15, RB18L20, RB18L25, RB18L40, RB18L50, RB18L60A, RB18L90A, and more from the Ryobi ONE+ range. Safety and Maintenance Use only original accessories and spare parts. Avoid contact with hot surfaces. Do not immerse the tool or battery in liquid. Clean using a dry cloth and store with batteries removed when not in use for extended periods. Imported by Techtronic Industries Australia Pty Ltd, Mount Waverley VIC 3149.
$118.80
You have seen 96 out of 879 products
Easy-to-use, low-odour products with straightforward instructions and tidy finishes—great for home fixes and craft. Prefer water clean-up and clear-drying where appearance matters. Use filters to refine by chemistry and set speed. Always review the product page and TDS/SDS.
