A high grade linseed oil putty with excellent adhesion for repairing and glazing wood and metal frames. For use on: Wood & metal (EXTERIOR & INTERIOR) Dries in: Skins over in 2-3 days depending on weather conditions. Ready to use: YES Colour: Light brown Ensure all surfaces are clean, sound and dry. Remove all old putty, dust off loose and crumbling material. • Bare timber should be primed with an oil-based primer before applying putty. • Knead putty thoroughly for smooth, even consistency in application. • Apply putty to working area with either a thumb or putty knife. When evenly applied, smooth off. • Always allow several days for putty to skin before applying an oil-based undercoat. Can be painted with either water or oil-based topcoat. Q. I used Polyfilla Putty on a window frame and have noticed some wrinkling on the surface. Is something wrong with the product? A. No. When this product is used on metal window frames exposed to heat, some surface wrinkling can occur. This will not affect the performance of the putty in any way.
$46.19
Imagine a liquid epoxy that is clear – A liquid epoxy with strength rivalling that of heavy duty paste epoxies – A liquid epoxy that has flexibility and is shatter resistant – A work time of 4 minutes and 1 hour cure time. Imagine NO LONGER! PC-Clear ™ Epoxy is a medium viscosity liquid epoxy system with greater clarity than other epoxies. This product is excellent for repairs and projects that must be less visible such as art objects or collectibles. PC-Clear™ epoxy is fast curing but allows ample time to apply and position the repair. After curing the epoxy does not become brittle, instead cured PC- Clear™ forms a tough resilient bond. PC-Clear™ can be used on more than just cosmetically critical repairs and in addition, it can be used for automotive, construction and facility repairs. Use PC-Clear™ when you are concerned about the appearance of your repair and a liquid epoxy is what you are looking for. Work time is about 4 minutes and cures in 1 hour. Here are just a few specific uses (there are hundreds of other uses): Fasten galvanized steel to a concrete floor. Bond sheet metal to wood or masonry. Seal and insulate electrical connections and electronic boards. Protect electronic components from vibration and moisture. Repair porcelain or sculptures. Reattach multiple broken pieces in a vase. How to prepare a surface for bonding with PC-Clear™ Epoxy Remove contaminants such as dust, dirt, oil and grime with a solvent such as Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner. A mild detergent solution in water is also good for removing contaminants. Use a clean paper towel or rag for wiping. Do not use Mineral Spirits or Paint Thinner for removing contaminants. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. How to clean-up after PC-Clear™ Epoxy application Clean up mixed epoxy before it cures with paper towels and solvent. Denatured Alcohol (ethanol), Acetone, Rubbing Alcohol (isopropyl alcohol) or Lacquer Thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be removed with paint stripper or remover. FAQ Is PC-Clear™ Epoxy different from other clear epoxies? Some epoxies claim to be clear but they have a strong yellow tint that develops after it cures. PC-Clear™ Epoxy has a very slight hint of yellow that does not increase after curing. How does PC-Clear™ Epoxy’s strength compare to other epoxies? PC-Clear Epoxy™ is a strong adhesive with Lap Shear Adhesion strength on steel of 2500 psi. Is PC-Clear™ Epoxy brittle? PC-Clear™ Epoxy is slightly flexible and more resilient than other liquid epoxies. How does outdoor exposure affect cured PC-Clear™? Ultraviolet light will cause cured PC-Clear’s™ appearance to change and may cause yellowing. What is the best way to mix PC-Clear™? How you mix PC-Clear™ Epoxy will affect the length of working time. Flat surface mixing spreads the epoxy over an area minimizing the exotherm’s effect on the curing reaction and maximizing the length of work life. Mixing in a container concentrates the exotherm contributing to an increased rate of reaction and decreasing the work life. Why does PC-Clear™ Epoxy have a strong odor? The epoxy resin is nearly odorless. The hardener is the smelly part. It has an odor described as smelling like sewer gas or hair treatments. This odor comes from the polymercaptan but goes away upon curing. Does PC-Clear™ Epoxy self-level? PC-Clear Epoxy™ is a liquid and is self-levelling. How many feet of does the PC-Superepoxy® 50 ml cartridge nozzle dispense? PC-Superepoxy® can dispense approximately 20 feet of 1/8 inch bead. Can PC-Clear™ Epoxy be colored or tinted? PC-Clear™ Epoxy can be tinted.
$14.34
Parfix is a two-part epoxy adhesive designed to give high bond strength to most common household materials. Fast setting Easy mix Rigid bond
$11.94
Parfix everyday adhesive is an easy mix, two-part epoxy adhesive provides a strong, rigid bond, designed for use with most common household materials including china, metal, glass, leather, rubber, wood and most plastics. Fast setting Easy mix Rigid bond
$5.00
Adhesive permanently remounts mirrors to windshields LOCTITE® Rearview Mirror Adhesive is approved and used by GM, Ford and Daimler-Chrysler. Permanently remounts mirrors to windshields. Achieves handling strength in seconds; mirror-mounting strength in 15 minutes. Mounting rearview mirrors to windshields.
$25.00
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled. Recommended on Great for crafting projects Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone Can be combined with fiberglass cloth for a durable patch Properties High impact resistance: won’t crack when drilled Can be tinted to match surrounding materials Water resistant and can be used outdoors Does not shrink Convenient instant mix syringe Consistently dispenses equal, uniformly mixed amounts of each component Sets in 40 to 60 seconds Quick completion of project HOW TO USE: Step 1: Safety Precautions Well-ventilated area, gloves. Step 2: Preparation Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place. Step 3: Application Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it. Step 4: Cleanup Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
$7.91
Part N° 546018 (MA3) LOCTITE AUTOMOTIVE REARVIEW MIRROR ADHESIVE • Special Loctite bonding system for attaching metal rear-view mirror buttons to windscreens. Ideal for larger mounting brackets • Absorbs difference in thermal expansion - also recommended for metal locks and hinges on side windows and glass to metal applications on furniture. Contents: 1 piece of nylon mesh 40mm x 40mm - Diagram 1 Part B. 1 tube of Loctite adhesive - Diagram 1 Part A. Contents are sufficient for one rear-view mirror application. Note: the adhesive must be used with the special nylon mesh Directions for use: - Where convenient, remove the metal bracket from the mirror bracket. Do not damage the metal bracket Place the car in shade for at least one hour before commencing the repair. The ideal temperature for this 2 repair is between 15°C and 25°C Diagram 3: Mark an outline of the bracket on the outside of the windscreen with a marking pen Ensure the position of the bracket will result in the mirror hanging in the correct way. - Remove all old adhesive from the bracket with fine sandpaper, and from the screen with a sharp blade or razor blade. Wipe clean the inside of the screen with an ammonia-based detergent or LOCTITE SF 3 7850 Orange hand cleaner, then wipe again with a clean cloth dampened in Methylated Spirit. Allow drying. Cut the nylon mesh to the exact shape of the metal bracket that will fit onto the windscreen. Hands must be clean and oil-free while doing this. - Cut the tip from the adhesive tube (Dia. 1, Part A), apply the adhesive from the tube and spread over the entire area of the metal bracket - Place the cut to size nylon mesh onto the adhesive on the metal bracket. Important. The adhesive will begin curing within 30 seconds of contact with the nylon mesh. Diagram 7: Note Ensure the bracket is in the correct position (top and bottom front and back) With the nylon mesh and adhesive assembled, press the bracket and mesh against the inside of the windscreen aligned with the marked location and hold firm for a minimum of 30 seconds Wipe off any excess adhesive, Allow adhesive to cure for at least 15 minutes before mounting the mirror to the bracket. Warning: Adhesive may attack some painted surfaces.
$19.95
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless. Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability. DIRECTIONS FOR USE: 1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding. 2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger. 3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform. 5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged. Structural Bonding - Fast Cure. Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance. Fixture time: 4-6 min Temperature Resistance: Up to 180°F (82°C)
$15.11
Overview Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free! Features Automatic Self-Mixing Nozzle No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance. Fast Setting & Long-Lasting Sets in just 5 minutes. Can be safely handled within 30 minutes. Attains full strength after 16 hours. Versatile Usage Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects. Superior Formulation 50% Epoxy Resin 50% Modified Amine Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C. How to Use Preparation Safety First: Always wear protective gloves and safety glasses. Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease. Application Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully. Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener. Mixing: Mix thoroughly before applying. Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary. Post-Application Cleanup: Use acetone for cleaning. Storage: Store in a cool, dry place with the nozzle end up.
$9.95
Bostik Epoxy Bond is a special two-part adhesive which, when mixed and allowed to set, produces bonds of immense strength. This resin based epoxy sets in approximately 5 minutes to give a permanent and colourless bond. It will adhere to pottery, china, metals, glass, wood, rigid and semi-rigid plastics and cardboard, etc. where an Industrial strength bond is required by handymen, hobbyists and tradesmen. FEATURES AND BENEFITS 1. Quick setting – will bond in 5 minutes 2. When fully cured, the adhesive can withstand boiling water for short periods of time. 3. Heat resistance rating of 60ºC temperature continuously. 4. Adhesive shear strength of up to 800 psi for metal/metal bonds APPLICATION 1. Surfaces to be joined must be clean, dry and free from dirt and grease. Metals should be abraded and washed with a petroleum solvent. China and pottery should be washed in detergent, rinsed and dried. 2. Dispense and mix thoroughly, sufficient material of the two parts to carry out the job at hand with a matchstick, screwdriver or similar implement. Reseal the nozzles of the syringe with the enclosed plug and tube with cap and store in an upright position (nozzles upward). 3. Apply a thin film of adhesive to one or both of the surfaces to be joined, press together and do not move until the adhesive has set - usually 5 minutes @ 20ºC. Very good handling strength is obtained after 20 minutes and maximum adhesion is achieved after 24 hours
$9.00
A strong and durable, fast setting two part epoxy adhesive that dries crystal clear making it ideal for areas where an invisible bond is required. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Weather and yellowing resistant. Shock resistant. Features: -Araldite is stronger than other glues due to the chemical reaction of the two parts. -Bonds a variety of surfaces -Dries Crystal Clear so there’s no visible evidence of repair -Quick setting in 5 minutes -No clamping necessary -High water resistance -Forms a rigid, durable bond -Can be used for gap filling (Surfaces need not mate closely) -Good chemical resistance -Heat Resistant -Doesn’t yellow over time so is ideal for use on glassware Appearance: Crystal Clear Where can this product be used? -Fixing a broken glass vase -Repairing jewellery -Toy repairs -Fixing ornaments or crockery -Fixing your handbag strap -Not suitable for bonding plastics such as Polypropylene and Polyethylene or for use on polystyrene -What materials is this product suitable for? -Glass -Metal -Wood -Fabric -Rigid Plastic – refer to Selley's plastic guide for more info -Crystal -Leather How to use this product: -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each -Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow the bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. -When using tube kit, ensure correct caps are replaced on each tube or they will adhere. Handy tips: -A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol). -Clamping is recommended for a stronger bond. -For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. -To extend product life replace caps immediately after use. -When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) -Wipe off any uncured Araldite with acetone or nail polish remover. -To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. -To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. -Keep a box of Selleys Sugar Soap Wipes around for quick & effective cleanup -For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Safety tips: -Avoid contact with the skin and eyes. -Avoid breathing vapour. -Do not use solvents near eyes or open wounds. -In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. -Non-toxic when set. Storage and re-use: Ensure caps or lids are replaced and product stored in a cool dry place.
$16.58
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$28.96
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Very quick setting in 90 seconds No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling Good chemical resistance Where can this product be used? General small household repairs Fixing gemstones to mounts Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Most Plastics How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately. Ensure correct caps are replaced on each tube or they will adhere. Handy tips Note: For information on how to identify plastics refer to the Selleys plastics guide. For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured Araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep a couple at home just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
$16.00
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
You have seen 63 out of 63 products
Clear, non‑corrosive formulas suitable for glass and mirror applications. Look for neutral cure and mirror‑safe indications where required. Ideal for décor, splashbacks and repairs. Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
