Ozito Trigger-Flow Hot Glue Gun 10 W is a reliable compact hot melt glue gun for quick bonding and model making chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 10 W pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Ozito Trigger-Flow for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Ozito Trigger-Flow Hot Glue Gun 10 W has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Cardboard displays and craft Light repairs and cable dressing Attaching trims, felt, and fabric accents Suitable surfaces The adhesive works well on the following surface types when properly prepared: Card, paper, fabric Wood trim and plastics that tolerate hot melt Ceramic ornaments Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of open time is short, assemble parts promptly after application. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Hot melt sets as it cools, giving fast handling strength. Full strength is reached once the bead has cooled through. Temperature and environmental performance Operate in a dry area. Avoid use on heat sensitive foams that may melt. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Peel away stray strands after cooling. Protect worktops with a mat. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Unplug and allow to cool before storage. Keep glue sticks sealed from dust. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$8.38
Get fast and reliable adhesion with Bostik Quick Glu Instant Fix Bond Spray. This 25g spray adhesive provides a strong, clear and lasting bond suitable for a wide range of materials used in craft, home and office projects. Key Features Instant bonding for quick and easy use Dries clear for a neat and professional finish Acid free formula that resists yellowing over time Works on wood, metal, ceramic, leather, paper and many plastics (not suitable for polyethylene or polypropylene) Compact 25g size ideal for small jobs and easy storage How to Use Ensure surfaces are clean, dry and free from grease or dust. Shake the can well before each use. Hold the can 15 to 20 cm from the surface and apply a light, even coat. Wait a few seconds until tacky before joining the surfaces. Press firmly together and hold for a few seconds for best results. After use, clear the nozzle by spraying briefly while holding the can upside down. Recommended Applications Arts and crafts projects DIY home repairs Paper, cardboard, leather and wood bonding Quick fixes requiring a clear and clean finish Safety and Storage Use only in well ventilated areas and avoid inhaling vapours. Keep away from heat, sparks and open flames as the product is flammable. Store in a cool, dry place away from direct sunlight. Keep out of reach of children. Bostik Quick Glu Instant Fix Bond Spray delivers a convenient and efficient solution for fast bonding on a wide variety of materials.
$8.50
Bostik Glu Tape is a clean, quick and mess free double sided adhesive for everyday sticking and craft projects. At 6 mm wide and 12 m long, it gives precise control for cards, scrapbooks, posters, school projects and office tasks. Why you will love it Instant stick with no drying time Clean finish with no liquid glue spills Thin 6 mm width for neat, accurate placement Strong hold on most paper and lightweight materials Great for home, school and office use Great for Card making and scrapbooking Mounting photos, prints and posters Sealing envelopes and gift wrapping School assignments and craft projects Suitable surfaces Paper and cardboard Lightweight foam and foamboard Most coated papers and photo papers How to use Ensure surfaces are clean, dry and free of dust or oils. Apply the tape along the area to be bonded, pressing down firmly. Peel away the release liner if present, then align and press surfaces together. Rub over the bond area to secure a strong hold. Tips Test on delicate or coated papers before full application. For best results, apply at room temperature and avoid stretching the tape. Store in a cool, dry place out of direct sunlight. Specifications Type: Double sided adhesive tape Width: 6 mm Length: 12 m Color: Clear adhesive Pack contents: 1 roll
$10.60
Bostik Super Glue Gel is a fast setting, non drip adhesive that stays where you put it for precise, clean bonds. The thixotropic gel formula is ideal for vertical surfaces and small gap filling, delivering reliable results on everyday repairs and crafts. Key features Fast setting gel for controlled application Non drip formula for vertical and overhead surfaces Small gap filling for close fitting parts Strong bond on many common materials Clear finish for neat repairs Ideal for Metal, rubber, most hard plastics, wood, ceramics, porcelain Small household repairs, models, craft and DIY fixes Precision bonding where liquid super glue may run Not suitable for Polyethylene, polypropylene, PTFE Very flexible materials or items regularly exposed to water immersion Food contact surfaces or aquarium use Directions Ensure surfaces are clean, dry and close fitting. Lightly roughen smooth surfaces if possible. Remove cap and apply a small bead of gel to one surface. A little goes a long way. Join parts immediately and hold firmly until set. Avoid moving the bond during curing. Allow the repair to rest for several minutes before light handling and longer for full strength. Handy tips Test on an inconspicuous area first. Use sparingly. Excess adhesive can slow cure. For porous materials, a second application may improve the bond. Clean up Wipe fresh squeeze out immediately. Once cured, carefully remove excess with a sharp blade. Adhesive may whiten on some surfaces if excess is left to cure. Storage and safety Close cap tightly after use and store upright in a cool, dry place. Bonds skin in seconds. Wear care when handling. If skin bonding occurs, do not pull apart. Soak in warm soapy water and gently roll apart. Use in a well ventilated area and keep out of reach of children.
$6.47
Bostik Repair All is a clear, multi-purpose adhesive for quick, durable repairs around the home, garage, and workshop. It bonds strongly, remains slightly flexible, and is water resistant once cured, making it suitable for everyday fixes and craft projects. Why you will love it Strong, long lasting bond Dries clear for a neat finish Water resistant once fully cured Flexible bond helps absorb vibration Suitable for indoor and outdoor use Works on Metal, wood, ceramics, glass, most rigid plastics, rubber, leather, fabric, and more. Always test on delicate or unknown materials first. Ideal for Household repairs and DIY Craft, hobbies, and school projects Fixing ornaments, toys, trims, and fittings Directions Ensure surfaces are clean, dry, and free of dust or grease. Lightly roughen smooth surfaces. Apply a thin even layer to one surface. Join parts together and press firmly. Support or clamp if needed. Wipe away any squeeze out immediately with a cloth dampened with solvent suitable for the substrate. Allow to set undisturbed. Handling strength is typically reached within hours. Full cure is usually achieved after 24 hours depending on bead size, temperature, and humidity. Clean up Uncured adhesive can be removed with a suitable solvent. Cured adhesive is best removed mechanically by trimming or carefully scraping. Good to know Not recommended for polyethylene, polypropylene, PTFE, or surfaces that will be in constant water immersion. Avoid contact with food or drinking water surfaces. Store upright in a cool dry place with cap tightly closed. Key details Brand Bostik Product Repair All Appearance Clear when dry Finish Flexible Water Resistance Yes, once cured Pack Size 20ml Always read the label and follow safety instructions. Keep out of reach of children.
$14.50
Keep your glue gun ready for any project with the Bostik HG3 Glue Gun Refills. These high quality hot melt sticks provide a smooth, even flow for clean and reliable bonding. Pack of 10 clear adhesive sticks Compatible with Bostik HG3 Glue Gun Creates a strong, flexible and transparent bond Suitable for wood, plastic, fabric, leather, ceramics and more Perfect for craft work, household repairs and DIY projects. The hot melt formula ensures quick adhesion with minimal mess, giving you professional results every time. How to use: Insert a glue stick into the back of your glue gun. Allow the gun to heat for a few minutes before use. Apply steady pressure on the trigger to release glue. Join surfaces immediately for best results. Let the glue cool completely before handling. Safety Information: Hot glue can cause burns. Avoid contact with skin and eyes. Keep out of reach of children. The Bostik HG3 Glue Gun Refills are ideal for quick fixes, decorative projects and reliable everyday bonding.
$15.21
Overview LOCTITE Super Glue All Plastics is a rapid dual-action adhesive kit featuring a precision super glue and a surface activator pen. Engineered to bond difficult plastics such as polyethylene (PE), polypropylene (PP) and PTFE, it forms clear, resilient bonds in seconds and resists water, most household chemicals and freezing temperatures. Ideal for repairs on toys, cameras, small automotive parts, wiper blades, rubber seals, figurines and other plastic components. Advanced bonding system: activator primes the surface; glue delivers high strength. Fuses hard-to-bond plastics: effective on PE, PP, PTFE and more. Fast & clear: sets in seconds, dries transparent for nearly invisible repairs. Durable: water-resistant and suitable for cold conditions. Surface Preparation Ensure both surfaces are clean, dry and close-fitting. Remove grease, oil, dust or loose particles. For best adhesion on very smooth plastics, lightly roughen with fine-grade sandpaper and wipe clean. Avoid use on soft foams, expanded polystyrene or highly porous materials. Always test on a small, inconspicuous area if unsure about compatibility. Application Instructions Prime with activator: Apply one or two thin coats to both bonding surfaces, ensuring full coverage. Re-cap the activator pen immediately. Allow to dry/react for 1–2 minutes. Apply adhesive: Place a minimal drop of glue on one surface only. Bring parts together immediately and hold firm pressure for at least 1 minute. Avoid shifting once contact is made. Cure: Leave undisturbed for 10 minutes. Full bond strength develops after 12–24 hours at room temperature. Coverage & Performance Only a thin film is required—one drop bonds most small mating areas. Initial handling strength is typically achieved within 5–30 seconds depending on substrates and conditions. Drying & Setting Time Initial set: 5–30 seconds* Handling time: ~1 minute Full cure: 12–24 hours Recommended conditions: 15–30 °C and ≥30% relative humidity *Setting and cure times vary with substrate, joint fit, temperature and humidity. Clean-Up & Storage Wipe nozzle to remove excess adhesive and replace caps immediately after use. Store upright in a cool, dry place away from sunlight and moisture. Do not refrigerate. Shelf life (unopened and properly stored): up to 18 months. Limitations Not recommended for glass, very flexible materials, soft foams or highly porous substrates. Not suitable for continuous water immersion or high-heat applications. For indoor use or dry environments; test before critical repairs. Safety & Handling Contains cyanoacrylate. Bonds skin and eyes in seconds. Avoid contact. Use in a well-ventilated area; consider gloves and eye protection. If skin is bonded, do not pull apart—soak in warm, soapy water and gently roll/separate. Acetone may assist on non-sensitive skin; avoid on plastics. If in eyes, rinse cautiously with water and seek medical attention immediately. Keep out of reach of children. Technical Data Product Type Two-part system: Activator + Cyanoacrylate Adhesive Substrates PE, PP, PTFE, many rigid plastics, rubber, selected metals Appearance Clear (dries transparent) Packaging Size 2 g adhesive + 4 ml activator Initial Set 5–30 seconds (substrate dependent) Full Cure 12–24 hours at ambient conditions Temperature Range Approx. −50 °C to +80 °C (typical for cured cyanoacrylates) Cleanup Mechanical removal once cured; avoid solvents on sensitive plastics What’s Included LOCTITE Super Glue (2 g) Surface Activator Pen (4 ml) Always follow on-pack directions. Performance will vary with materials, joint design and environmental conditions.
$10.80
Holds up to 13.6Kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Recommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$11.55
Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistant DetailsFor your toughest jobs, go for our strongest hold – Scotch™ Extreme Mounting Tape. Equipped with our powerful permanent adhesive, this double-sided tape defies is weather resistant for a long-lasting bond, indoors and outdoors. So whether you're mounting shelves in your new apartment, or adding wall organisation to the garage, Scotch™ Extreme Mounting Tape does the job quickly, easily and without the hassle of tools. Holds up to 13.4kg, 17cm holds 1kgHang or mount kitchen splashbacks, outdoor décor or organise your tool shedIdeal for both indoor and outdoor use, no need for nails and screwsUV, temperature and humidity resistantRecommended Surfaces: Wood, Metal, Concrete, Brick, Gyprock, Tiles, Acrylic. Not recommended for DrywallWaterproof once bonded to surfaceUses 3M VHB™ Tape, Extreme strength and high conformability
$12.95
3 x 1g originally sealed tubes ideal portion for one application. in a handy storage box reaches the smallest corners and joints Extra strong super glue in 3 x 1g tubes, packaged in a small storage box, ensuring optimal quality for every new application. The liquid adhesive reaches the smallest corners and joints. Materials Glues many plastics, porcelain, ceramic, metal, wood and rubber. Not suitable for leather clothing, PE, PP nor styrofoam. Use and Handling Instructions Surfaces to be stuck together must fit exactly and must be dry and free of dust and grease. Apply a thin layer of adhesive to one side. The thinner the film of adhesive, the stronger the bond. Press the parts together immediately and hold in place for a short time. Breathing upon the surfaces to be stuck will speed up bonding. After use, wipe the applicator tip dry and close firmly. Will last longer if stored in a cool place.
$11.50
PROPERTIES Extra strong Fast but temporarily adjustable Does not drip Ideal for porous materials and vertical surfaces Dishwasher proof and water resistant APPLICATION SUITABLE FOR: Ideal for small-area bonds. Glues almost all solid and flexible materials like ceramics, leather, rubber, many plastics (such as rigid PVC, ABS, PS, Plexiglas®, polycarbonate (Makrolon®), and phenolic resins (Bakelite®)), porcelain, metal, wood, cork, felt, and cloth (check suitability first). Only partly suitable for glass (over a certain period of time the bond becomes brittle, causing it to weaken). Ideal for porous materials. NOT SUITABLE FOR: Not suitable for PE, PP, silicone resins, PTFE, Styrofoam®, fabrics and leather clothing. BEFORE USE: Working conditions Do not use at temperatures below +10 °C. The glue responds best to an air humidity level of 50-70 %. Surface requirements Surfaces to be glued must be clean, dry, and free of dust and grease, and must fit exactly. Preliminary surface treatment Any dust, oil, grease, wax or separating agent should be thoroughly removed from the surfaces to be stuck together. The best way to achieve this is to rub the parts a number of times with appropriate solvents, such as acetone (if suitable for the material – check first!). For metals and metal alloys it is usually sufficient to roughen the surface using emery paper or by grinding or brushing. DURING USE: Directions for use 1. To pierce the membrane, turn the cap clockwise firmly onto the tube. Tip: do not press the tube while piercing. 2. Unscrew the cap to reveal the applicator. Apply the adhesive directly from the tube, using the nozzle, as thinly as possible onto one side (too much glue slows down the curing process significantly). Press parts together immediately. After use, clean nozzle with a dry tissue and replace cap. Advice When glueing at low humidity, curing time can be shortened by briefly breathing onto one of the parts to be assembled. The best glueing results are reached at room temperature. Points of attention Contains cyanoacrylate. Bonds skin and eyelids together in seconds. If product comes into contact with the eyes, rinse immediately with plenty of water and seek medical advice. In case of contact with skin, glue can be dissolved by soaking in warm soapy water. Then apply a skin cream. May cause respiratory irritation. Avoid breathing vapours. Keep out of the reach of children. AFTER USE: Stains/residue Wipe off excess glue immediately with a dry cloth. After curing, glue residue is very difficult to remove. Acetone will dissolve glue but very slowly (check suitability first). Storage conditions Store in a dry, cool, frost-free place. Storage below +5 °C (in refrigerator) ensures maximum shelf life.
$7.00
Ultra-fast and extremely strong universal super glue. Its liquid formula is easy to spread and flows into smallest corners and joints. UHU Super Glue is easy to apply, bonds quickly and provides lasting, extremely strong results. You can use it on a variety of materials so it's perfect for keeping handy in the classroom at school. You can use the glue on plastics, ceramics, wood, porcelain, metal and rubbers. It bonds quickly for fast results. The glue will flow into small corners and tight spaces. The results are extremely strong and long lasting.
$7.00
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/949_1005_f9e8bad8-cc2d-4f12-888b-f7be3932182b.jpg?v=1754716338&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black Grip x 1.5m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_75d61b67-9ac6-4739-9648-1e850e68af71.png?v=1754716338&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/9315284530374_556be8c2-fd79-4d44-bfb3-029f3b567466.jpg?v=1754716329&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [3 Pack]](http://gluesaustralia.com.au/cdn/shop/files/93152845.png?v=1754716329&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$12.94
The Original Super Glue® Corporation's newest product is the ACCUTOOL® . The ACCUTOOL® has a revolutionary, easy to hold design and features high-performance cyanoacrylate. The new ACCUTOOL® precisely applies the product where you want it, how you want it. You can get a continuous stream or drop-at-a-time application based on the amount of pressure you apply to the dispenser buttons. The Original Super Glue®: Fast. Easy. Effective. Pacer Technology Super Glue’s AccuToolTM (19025) is a quick-setting adhesive in a precision applicator that works on oily & dirty surfaces to bond most porous and non-porous materials, such as: Metal Leather Ceramic Wood Fabric Most plastics Porcelain Rubber Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Instructions: NOTE: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$15.50
Original formula Super Glue forms the strongest bonds in tight joints between clean breaks or smooth surfaces. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly sets in seconds and is packaged in a long lasting 2-gram tube. The extra slim card is perfect for tight displays, end-caps and clip strips. Pacer Technology Super Glue is a quick-setting adhesive that bonds strongly and works best on: Metal Rubber Most Plastics Aluminium Ceramic China Wood Pottery Jewellery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Use: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep container pointed away from face and body. Carefully follow opening directions on package. Unscrew cap while keeping container pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before resealing cap securely. Storage: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$3.50
Super Glue gel's thick viscosity is perfect for clean, vertical, porous (wood, hard leather and porcelain) surfaces. Gels allow for a more accurate application as they do not drip or run. Works best on: Leather Metal Vinyl Rubber Most plastics Aluminum Ceramics Hard & Soft Wood China Pottery Jewelry NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial color: Clear, transparent Final color: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Use: NOTE: For best results, surfaces should be clean and dry and items should fit together well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. Storage: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$18.00
Original formula Super Glue forms the strongest bonds in tight joints between clean breaks or smooth surfaces. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly and sets in seconds! Packaged in a 20-gram break-away tip bottle this product is ideal for larger projects that require greater amounts of Super Glue. Works best on: Metal Rubber Most Plastics Aluminium Ceramic China Wood Pottery Jewellery NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rear view mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) USE INSTRUCTIONS: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep container pointed away from face and body. Carefully follow opening directions on package. Unscrew cap while keeping container pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before resealing cap securely. Storage: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$12.50
A handy Super Glue pen with unique press tabs, for steady flow or drop-at-a-time application, is great to have with you at home or on the road. Great when you're looking for a precise application. Best used with non-porous application parts such as metal and rubber. The glue bonds instantly and sets in seconds! NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Not for porous materials such as paper, fabric or foam rubber. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800F (-540 to 820C) Instructions: NOTE: For best results, surfaces should be clean & dry and parts should mate well. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Keep pen tip away from face and body. Follow directions on the card for proper opening steps. 2. Apply to one surface, using 1 drop per square inch of surface. Do not spread glue with fingers – use applicator nozzle tip. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe tip if the adhesive has accumulated before inserting a pin in the end of tube securely after use. STORAGE AND SHELF LIFE: Replace outer cap and store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause burns. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$45.00
High-Performance Future Glue® works exceptionally well with tough jobs. Surfaces do not need to be cleaned! Its powerful adhesive formula works on dirty, greasy surfaces, and resists high and low temperatures as well as most chemicals. Its instant bonding power can be used for almost all porous and non-porous materials. The medium viscosity penetrates into preassembled and close-fitting parts. Works best on Aluminum Ceramic China Corkboard Hard & Soft Wood Jewelry Leather Metal Most Plastics Porcelain Pottery Rubber Properties Initial colour Clear, transparent Final color: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -65 to 180 F (-54 to 82 C) USE INSTRUCTIONS For best results, surfaces should be clean and dry. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Carefully follow tube-opening directions on package. Unscrew cap while keeping tube pointed away from the face. 2. Apply to one surface, using 1 drop per square inch of surface. Assemble parts and hold together with pressure for 15 seconds or until set. 3. Wipe the top of nozzle if the adhesive has accumulated before recapping tube securely after use. STORAGE AND SHELF LIFE: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$18.00
HandiTAK® is non-toxic, acid and lignin free. This reusable adhesive replaces tape, pushpins and tacks. It works on most surfaces and is great for securing pictures, keys, pens and lots of other items. Simply knead a small piece of HandiTAK® into a ball, place it between surfaces to be fastened and press firmly. Works best on: China, Crystal, Greeting Cards, Notes, Party Decorations, Posters, Straighten Pictures, Telephone, Pads Pacer Technology Super Glue’s HandiTak (HT, HT2) is a non-toxic (conforms to ASTM D-4236) reusable adhesive that replaces tape, pushpins and tacks and works on most surfaces. Properties: Appearance - yellow rubber-based mounting tape with a mild odour. (Note: contains a synthetic rubber ingredient with no natural latex). Instructions: 1. Knead a small piece of HandiTak into a ball, place it between surfaces to be fastened, and press firmly. 2. To remove HandiTak, gently roll product into a ball and lift from the surface. Use the ball to aid in removing any remaining product. SAFETY AND HANDLING PRECAUTIONS Contains rubber-based hydrocarbon mixture. Caution: HandiTak may leave some oily residue on some surfaces. If this happens, use Lighter Fluid or mineral spirits to remove residue. Do not use HandiTak on soft-flocked wallpaper, newly painted surfaces, or for hanging heavy objects such as mirrors and framed pictures. Avoid prolonged skin contact.
$8.50
This new, innovative dispensing system allows for accurate control while utilizing an advanced formula of the Super Glue Corporation's signature product cyanoacrylate (Super Glue GEL). The easy to hold applicator design allows for either continuous stream or single drop control. No more sticky fingers! This glue works great when adhering to porous or vertical surfaces. It will not drip or run! Works best on: Aluminum Ceramic China Hard & Soft Wood Jewelry Metal Most Plastics Pottery Rubber Vinyl Pacer Technology AccuTool Gel (19026) is a quick-setting, non-sagging gel adhesive that fills gaps & works best on: Leather Metal Vinyl Rubber Most plastics Aluminium Ceramics Hard & Soft Wood China Pottery Jewellery Fingernails NOTE: Not for use with Teflon, polyethylene, polypropylene, certain silicone rubber types, glass, rearview mirrors or parts that are subjected to great shock or continuous immersion in water. Properties: Initial colour: Clear, transparent Final colour: Clear Set time: 10-30 seconds Full Strength: 24 hours Operating Temperature Range: -650 to 1800 F (-540 to 820C) Use: For best results, items should fit closely together. 1. Protect clothing and work surfaces (metal foil works well). Use in a well-ventilated area. Refer to package for special opening instructions – has Self Piercing “Ratchet” Opener. After opening, remove the outer cap for use. 2. Apply sparingly to one surface using 1 drop per square inch. Assemble parts and hold together with pressure for 15 seconds or until set. 3. After use, wipe tip before replacing cap to prevent sticking and close bottle securely. Storage and Shelf Life: Store upright in a cool area away from sunlight or heat sources. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains cyanoacrylate. CAUTION: Eye Irritant. Bonds skin & eyes in seconds. Use with adequate ventilation. Avoid contact with clothing as can cause a burn. In case of eye contact, flush with water for 15 minutes; get medical attention for eye or internal contact. To remove from skin, soak in acetone nail polish remover & gently peel adhesive off with a fingernail; water exposure will wear off residual adhesive in a few days (do not use polish remover around the eye area). KEEP OUT OF REACH OF CHILDREN.
$9.95
Contact Cement is a flexible acrylic contact adhesive used to bond tile, rubber, wood, metal, formica, most plastics and much more. Pacer Technology Super Glue Contact Cement (T-CC) is a single component flexible acrylic contact adhesive that remains flexible after cure and is best used for: • Tile • Rubber • Wood • Metal • Masonite • Particle Board • Plywood • Leather • Formica • Plastic • Laminates PROPERTIES: Initial Color: Amber Dry Time: 30 minutes Final Color: Amber Full Strength: 24 hours Open Time: 10 minutes Operating Temperature Range: 15° to 150°F -9° to 66°C Instructions: Use in a well-ventilated area. 1. Surfaces should be clean and dry. For best results, use fine sandpaper to roughen the surface. 2. Apply Contact Cement to both surfaces and wait 10 minutes. 3. Press parts together. Clamp heavier parts together. Allow 30 minutes for drying time. 4. For optimum strength in all applications, wait 24 hours before using the repaired object. 5. Clean off tube or bottle top and tightly cap adhesive. Store upright and away from heat sources. Note: Solvents may evaporate from bottle or tube if left open for prolonged periods. Storage: Store in a cool area away from sunlight or heat. Stored under these conditions, a one-year shelf life can be expected. Safety: Contains methyl ethyl ketone, hexane and ethyl acetate. Warning – liquid adhesive is extremely flammable. Harmful or fatal if swallowed. Injurious to eyes with direct contact. Avoid prolonged breathing of vapours and prolonged skin contact. Wear suitable protective clothing and gloves. Use and store in a well-ventilated area away from heat, sparks or flame. In case of eye contact, flush with water for 15 minutes and seek medical advice. If swallowed, contact a physician immediately and show the container label. Wash hands & skin with soap and water after use. KEEP OUT OF REACH OF CHILDREN.
$7.95
Super Glue Glass Adhesive securely attaches items to windows and mirrors. This product works well with glass beads, stemware and clear glass windows. It is water resistant, dries crystal clear, and cures after 10 minutes following direct UV exposure Works best on Glass to Ceramic Glass to Glass Glass to Metal Glass to Plastic Properties -Initial colour: Clear -Set Time: 2-5 seconds in sunlight or 150mw/cm2, 200 watt/in UV bulb @ 240-400nm or 100mw/cm2, 150 watt Halogen bulb @ 400+ nm. -Final colour: Clear -Handling Time: 10 minutes -Full Strength: 24 hours -Operating Temperature Range: -400 to 1500F (-400 to 660C) Use Instructions: Use in a well-ventilated area. Avoid direct skin contact. 1. Surfaces should be clean, dry and close fitting. Glass Adhesive will fill small gaps. 2. Wipe surfaces with nail polish remover (acetone) or rubbing alcohol (isopropanol). Allow drying at least 20 minutes. 3. Uncap the syringe. The adhesive must be shielded from UV light during application to avoid premature curing. Use adhesive sparingly, using enough to just cover one surface to be bonded. 4. Join parts, making sure that they are correctly positioned. Wipe off excess adhesive before exposure using a clean cloth with mineral spirits or acetone. 5. Expose joined parts to UV sunlight or halogen lamp. In strong sunlight, a clear bond develops in 30 seconds. For cloudy conditions, allow 1-2 minutes. Bond strength continues to develop over 24 hours. 6. Excess cured adhesive can be removed with a blade. 7. After use, wipe syringe tip and recap. Store upright. NOTE: Clear Glass Adhesive is not suitable for bonding parts exposed to oven temperatures or for deep coloured stained glass applications. Storage And Sheld Life -Store in a cool area away from sunlight or heat. Protect from freezing. Stored under these conditions, a one-year shelf life can be expected. SAFETY AND HANDLING PRECAUTIONS Contains Urethane acrylate oligomer, acrylate ester & acrylic acid. May cause an allergic skin reaction. Eye, skin and respiratory irritant. Use and store in a well-ventilated area. For eye contact, flush with water for 15 minutes and get medical attention. Wash skin thoroughly with soap & water after use. KEEP OUT OF REACH OF CHILDREN.
$9.95
Instant Setting Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 90 seconds Pacer Technology Super Glue 90 Second Instant Epoxy Adhesive (SY-IN, 15353) works best on: • All Purpose • Ceramic • Glass • Wood • Leather • Fiberglass • Metals • Most Plastics Properties: Initial color: Clear to amber Mix Ratio (parts by volume): 1:1 Final color: Light yellow Maximum Gap: .25” Set Time: 90 Seconds @ 65-80F Hardness, Shore D: 75-85 (After full cure) Handling Time: After 10 minutes Shear Strength, Steel: 2000 psi (± 20%) Full Strength: 24 hours Operating Temperature Range:-400 to 1400F (-400 to 600C) Use: 1. Surfaces should be clean and dry, free from oil and grease. 2. Roughen surfaces with emery cloth or sandpaper for best results. 3. Dispense from container following package directions and mix thoroughly until color is uniform. 4. Apply to both surfaces and mate parts together. 5. Remove excess epoxy immediately with denatured alcohol. 6. Sets in 90 seconds at room temperature (77F or 25C) with full cure in 24 hours. STORAGE AND SHELF LIFE After use, wipe tips to remove residual product and reseal container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected.
$25.00
Tarzan’s Grip Super Glue is a fast-setting cyanoacrylic acid ester based adhesive. Tarzan's Grip Super Glue dries colourless. Special multi-purpose formula allows product to bond to a variety of surfaces Quick-setting Dries clear, therefore no mess
$6.06
Tarzan's Grip Shockproof Super Glue is a high strength, rubber toughened adhesive that dries clear for a multitude of applications. In addition to offering a superior bond on metals, it is ideal for use with wood, rubber, leather, china, paper and most plastics. It resists extreme temperatures of up to 150C. Sets in around 2 to 3 minutes Impact resistant Heat resistant Superior bond on metals
$10.44
Instant set, low viscosity, multipurpose super glue Suitable for bonding substrates with very smooth surfaces Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood and other materials. It is especially suitable for bonding pieces with very smooth surfaces. Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Characteristics and advantages: One Component Easy to apply, low viscosity Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, leather Low consumption adhesive Versatile allows adhesion between different materials Colourless Durable COLOUR Clear Storage 12 months from date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5ºC and +25ºC. Refrigeration to +5ºC gives optimum storage stability.
$28.00
Medium viscosity, ethyl cyanoacrylate based instant setting adhesive where very fast cure speed is required. Features: -Instant set, medium viscosity, multipurpose super glue -Suitable for bonding substrates with smooth surfaces -Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals -Controlled dosage applicator nozzle Use: -As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, leather, wood, paper and other materials. It is especially suitable for bonding pieces with very smooth surfaces. -Small repairs to glasses, shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Characteristics and Advantages -One Component -Easy to apply, middle viscosity -Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper -Low consumption adhesive -Versatile allows adhesion between different materials -Colourless -Durable Colour: Clear Shelf-Life: 12 months from the date of production if stored in unopened and undamaged, original sealed containers, in dry conditions and protected from direct sunlight at temperatures between +5°C and +25°C. Refrigeration to +5°C gives optimum storage stability.
$12.00
Instant set, high viscosity, multipurpose super glue Suitable for bonding substrates with irregular surfaces and in vertical applications Super high strength bond to most plastics, rubber, timber, ceramics, paper, card, leather and metals Controlled dosage applicator nozzle Use: As an instant setting adhesive for small bonding jobs such as bonding most metals, plastics, rubber, fabrics, wood, paper and other materials Can be used on porous substrates such as porcelain and china Small repairs to glasses, bonded shoe soles, picture frames, ceramics, toys and small electronic equipment, etc. Surfaces with small irregularities max. 0.5 mm On vertical surfaces Characteristics and Advantages One Component Easy to apply, non-sag, gel consistency Very rapid, tenacious bond to numerous substrates, e.g., plastics, rubber, metals, wood, ceramics, paper, card Low consumption adhesive Versatile, allows adhesion between different materials Colourless Durable Packaging 3 g Tube
$12.00
![Sika Sikaflex 118 Extreme Grab 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/7612895530055_35bcc6bf-bbee-4219-b850-30fa7a6b83ac.png?v=1754711711&width=645)
Sikaflex®-118 Extreme Grab is a 1- part construction adhesive with very high initial grab which bonds most construction material substrates. Internal and external use. Very high initial grab Fixing of heavy objects without temporary fixation Good workability Usage An adhesive to bond most construction components and materials such as: Concrete Masonry Most stones Ceramic Wood Metals Glass Mirrors* Advantages Very high initial grab Fixing of heavy objects without temporary fixation Good workability Very low emissions Adhesive-sealant with CE marking Packaging 290 ml cartridge, 12 cartridges per box Colour White Composition Silane terminated polymer Storage conditions The product must be stored in original, unopened and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +25 °C. Always refer to packaging. Density ~1.40 kg/l Technical Information Shore A hardness ~50 (after 28 d) Tensile strength ~2.2 N/mm2 Tear propagation resistance ~10.0 N/mm Service temperature −40 °C min. / +80 °C max. SUBSTRATE PREPARATION The substrate must be sound, clean, dry and free of all contaminants such as dirt, oil, grease, cement laitance, old sealants and poorly bonded paint coatings which could affect adhesion of the adhesive. For optimum adhesion and critical, high performance applications the following priming and/or pre-treatment procedures shall be followed: Non-porous substrates Aluminium, anodised aluminium, stainless steel, galvanised steel, powder coated metals or glazed tiles, slightly roughen surface with a fine abrasive pad. Clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. Before bonding / sealing, allow a waiting time of > 15 minutes (< 6 hours). Other metals, such as copper, brass and titanium-zinc, clean and pre-treat using Sika® Aktivator-205 applied with a clean cloth. After a waiting time of > 15 minutes (< 6 hours). Apply Sika® Primer-3 N applied by brush. Allow a further waiting time of > 30 minutes (< 8 hours) before bonding / sealing. PVC has to be cleaned and pre-treated using Sika® Primer-215 applied with a brush. Allow a waiting time of > 15 minutes (< 8 hours) before bonding / sealing. Porous substrates Concrete, aerated concrete and cement based renders, mortars and bricks, prime surface using Sika® Primer-3 N applied by brush. Before bonding / sealing, allow a waiting time of > 30 minutes (< 8 hours). For more detailed advice and instructions contact Sika Technical Services. Note: Primers are adhesion promoters and not an alternative to improve poor preparation / cleaning of joint surfaces. Primers also improve the long term adhesion performance of a sealed joint. CLEANING OF EQUIPMENT Clean all tools and application equipment immediately after use with Sika® Remover-208. Once cured, hardened material can only be removed mechanically. For cleaning skin use Sika® Hand Wipes.
$25.60
Why Choose Selleys Super Glue Adjustable Gel? Selleys Super Glue Adjustable Gel is designed for everyday household repairs, delivering precision and convenience. Its fast-acting formula bonds in just 30 seconds, while the adjustable setting time allows for perfect alignment before the adhesive sets. Ideal for use on a wide range of materials, it’s your go-to solution for quick and reliable fixes. Key Benefits: Adjustable Setting Time: Allows precise alignment before setting. Rapid Bonding: Bonds in 30 seconds for fast repairs. Versatile: Adheres to ceramics, china, metal, wood, and most plastics. Easy to Use: No mixing required, with a convenient gel formulation for clean application. Where Can This Product Be Used? Everyday household repairs on: Ceramic and China Metal and Wood Most Plastics* What Materials Is It Suitable For? Bonds a variety of porous and non-porous surfaces. Note: Not recommended for use on leather, polyethylene, polypropylene, or PTFE. Avoid applications involving exposure to water or dishwashers. How to Use Selleys Super Glue Adjustable Gel Prepare: Pierce the seal by attaching the nozzle with the cap and turning clockwise. Ensure surfaces are clean, dry, and free from dust, dirt, and grease. Apply: Apply a small amount of adhesive to the surfaces to be bonded. Press surfaces together gently and hold for several minutes to ensure sufficient bond strength. After Use: Wipe the nozzle clean with a cloth or paper. Replace the cap securely. Limitations Not suitable for use on leather, polyethylene, polypropylene, or PTFE. Will not permanently bond vessels exposed to water or dishwashers. Handy Tips for Best Results Ideal for vertical applications and slightly porous materials. Use 1 drop per cm² for optimal bonding. Sets in 30 seconds, achieving maximum bond strength in 24 hours. Clean-Up Instructions Wipe the tip of the tube with a cloth or paper after use. Replace the cap tightly to avoid drying out the product. Product Details Size: 1g Tube Colour: Clear Technology: Cyanoacrylate Recommended Use: Interior Transform your household repairs with the precision and reliability of Selleys Super Glue Adjustable Gel. Perfect for quick fixes, durable bonds, and easy application!
$9.59
Selleys Storm Waterproof Tape is a quick and easy way to seal and patch most objects*. It can be applied in the rain to stop leaks in an instant. Storm Waterproof Tape stops water leaks for 48 hours, making it ideal for emergency fixes until permanent repairs can be made. Features Waterproof & airtight seal* – Wet or Dry Stops active water leaks for up to 48 hours* Sticks to wet surfaces* Removable Suitable for interior and exterior Suitable for fresh, salt & chlorinated water Easy-to-use, DIY optimised format Where can this product be used? Can be used on gutters & flashing, down pipes, caravans, tents & tarps, rubber/plastic/vinyl pool liners, PVC piping, inflatable pool toys, small boats & kayaks air mattresses, umbrellas and more! Suitable for Aluminium, Galvanised Steel, Colorbond® Steel, Copper, Brass, Fibreglass, some rubbers and plastics* Ensure surface is free of dirt, grease and oil Cut tape or patch to desired size. Ensure there is at least 2-3cm of tape extending beyond each edge of the hole Remove backing paper, position carefully and press down firmly Once in position, rub firmly to ensure no air or water bubbles are left under the tape, and ensure good contact between the tape and substrate Leave tape until permanent repairs can be made
$25.00
A specially formulated adhesive and primer system that delivers a strong and shock-resistant bond on all plastics*, even polyethylene, polypropylene & ABS. Features Strong bond on all plastics*, even difficult rigid plastics like polyethylene, polypropylene & ABS Shock resistant, giving you a longer-lasting fix Fast setting in 30 seconds Also bonds plastic to non-plastic materials such as metals, timber, china, rubber, leather, and paper *Does not work on PTFE (Teflon) Where can this product be used? To repair plastic items made of PP, PE and ABS, e.g. plastic toys, office items, remote control What materials is this product suitable for? ALL plastics* including polyethylene, polypropylene and ABS Metals Timber China Rubber Leather Paper How to Use Use the primer pen to apply one coat on each plastic surface to be bonded. Primer pen will appear clear on the surface. Pierce seal at end of the adhesive tube by attaching nozzle & cap and turning clockwise. Remove cap and apply a small amount of glue to one surface only. Limitations: Not suitable for glass or foam, use Selleys Araldite Ultra Clear for glass or Selleys Power Grip Original for polystyrene foam. Product only works on some rubbers and will not work on PTFE. May cause leather to harden or discolour, test on an inconspicuous area first.
$10.29
Please refer to instructions on the photo of the back of the pack
$12.00
Selleys KwikGrip Spray 350g: The All-Purpose Adhesive for Absorbent & Non-Absorbent Surfaces Adhesive Mastery: Quick, Clear & Heat Resistant Discover the power of Selleys KwikGrip Spray 350g, a versatile adhesive spray that bonds instantly on contact. Ideal for both absorbent and non-absorbent surfaces, it offers a quick-drying and heat-resistant solution for a multitude of projects. Key Features: Versatile adhesive spray Durable bond Fast drying and dries clear Heat resistance up to 70°C Common Applications: Car upholstery repairs Fixing laminate on tables and bench tops Patching vinyl flooring Art and craft projects And many more... Compatible Materials: Laminated plastics Timber Craft foam Aluminium Leather Canvas Rubber Most plastics* How to Use: USE ONLY IN A WELL VENTILATED AREA. Shake the can well. Ensure surfaces are clean and dry. Hold the can 20cm away and spray surfaces evenly. For a permanent bond, spray both surfaces and wait until touch dry before pressing together. Clamp overnight for a firm bond. For a temporary bond, spray one surface and press together while still tacky. Limitations: Not suitable for bonding rough, ill-fitting surfaces or certain plastics like polyethylene or polypropylene. Refer to the guidelines for alternative solutions. Handy Tips: After use, clean the nozzle by inverting the can and spraying until clear
$21.00
A solvent-based, heat resistant, flexible contact adhesive suitable for bonding both absorbent and non-absorbent surfaces. It forms an instant bond on contact of two surfaces. The gel form allows application without dripping or ‘stringing’. Great for vertical surfaces. Features Heat resistance up to 130C No clamping required Suitable for interior and exterior jobs Cured adhesive is resistant to dilute acids and alkalis Immediate set on contact. Maximum strength after 24 hours Gel Grip has a thicker consistency than Kwik Grip and so is ideal for vertical applications as it won’t run Gel form prevents running or stringing Easy to spread by brush and ideal for use on vertical surfaces Where can this product be used? Vertical surfaces where dripping and running is a concern Bonding veneers of timber and laminated plastics, eg. Laminex and Formica to bench or table tops Areas where clamping or pressing facilities are either not available or difficult to use Patching vinyl Flooring Replacing a vinyl tile Cork tiling Laying a vinyl floor Fixing laminate to tables, benchtops etc Repairing canvas tents and outdoor equipment Bonding metal or laminate sheeting Replacing trim, rubbers and weather seals in cars Adhering flexible or other material to Aluminium Joining, repairing holes in tents, car covers etc Some plastics such as vinyl sheeting and polystyrene are attacked by Gel Grip. Test in an inconspicuous area prior to application. Can cause discolouration and bubbling when used for vinyl flooring materials, seek the advice of flooring material manufacturer before using Gel Grip. We recommend Kwik Grip Advanced for these applications Contains highly flammable solvent and care should be taken to ensure all fire precautions are observed. Cannot be used for application in temperatures below 10oC. Suitable for porous materials but not for rough, ill-fitting surfaces. (Consider the suitability of alternative products such as Liquid Nails for rough ill-fitting surfaces). What materials is this product suitable for? Cork Rubber Felt Canvas Leather Metals Timber Laminated plastics (laminex, formica) Hardboard Compressed board How to use this product Ensure that surfaces to be bonded are clean, dry and free from grease or paint. Cut laminated plastic sheet slightly oversize all round. Completely cover both surfaces with adhesive and keep apart until touch dry – no more than 40 minutes. Position the items carefully, still keeping surfaces apart with dowels or heavy craft paper and working from one edge press surfaces firmly together. Secure bond by running a roller over the bonded surfaces or else by hammering the surface from the centre outwards using a padded block. For bonding other materials, apply as for laminated plastics above. When small surface areas are to be joined a wet bond may be used. Simply apply Gel Grip to one surface then bring the surfaces together and clamp until dry. Handy tips Care should be taken to test plastics prior to use as solvents present will attack some grades such as polystyrene and sheet vinyl. Use Kwik Grip Advanced for these applications. Keep container sealed when not in use. Coverage – up to 5 square metres/litre (bonded area 2.5 square metres/litre) depending on porosity of surfaces and thickness of applications For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Safety tips Ensure thorough ventilation when using. Avoid using in a confined space for prolonged periods. Use Kwik Grip Advanced as a low fume alternative. Avoid skin contact as solvents in Gel Grip have a degreasing effect and may result in irritation. If in eyes flush with plenty of water for 15 minutes. Seek medical advice. If poisoning occurs, contact a doctor or Poisons Information Centre. Phone Australia 131 126 or New Zealand 0800 764 766. If swallowed, do not induce vomiting. Give a glass of water. Highly flammable. Do not use in the same area as flame, fire or spark producing apparatus or machinery. This product should NOT be accessible to juveniles, because of its solvent content. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use Clean Up While wet, adhesive can be removed using mineral turps. Cured adhesive is very difficult to remove. Tools and other equipment on which Gel Grip has dried may be cleaned by soaking in Toluol or lacquer thinner. Excess adhesive on the face of the jointed materials may also be removed with solvent, but care should be taken that the materials themselves are not damaged by the solvent. Store in a cool area away from ignition sources and out of direct sunlight.
$8.00
Fast setting supa glue that dries colourless and sets in 10 seconds. Features Bonds a variety of surfaces Quick setting – only takes 10 seconds Dries clear, therefore no mess No mixing required No clamping necessary Heat resistant: approx 80C maximum Non toxic when set Water resistant Application range: -55°C to +80°C Where can this product be used? Ideal for small repair jobs or when immediate results are required Supa Glue will bond non-porous surfaces Supa Glue is water resistant not water proof, so do not use in areas continually exposed to moisture as it will weaken the bond. Supa Glue is generally not flexible and has low impact resistance. ie will probably shatter if dropped. For these applications use SELLEYS Quick Fix Shock Proof or SELLEYS Urethane Bond. Supa Glue’s bond strength is excellent where surfaces to be bonded are a good close fit. Where gap filling is required use SELLEYS URETHANE BOND or ARALDITE or for very minor gap filling you can use SELLEYS Quick Fix Gel. Supa Glue is not recommended for use on paper. Not suitable for bonding plastics such as polyethylene, polypropylene or Teflon?. Supa Glue will not permanently bond glass or materials containing alkaline elements. What materials is this product suitable for? Rubber Some plastics Wood Metals How to use this product The seal at the end of the metal tube should be pierced carefully with the reverse end of the cap. Ensure that the tube is not squeezed while the seal is being pierced. Replace plastic nozzle. Surfaces to be bonded should fit exactly and should be clean, dry and free of dust, dirt and grease. Apply a drop of Supa Glue to only one of the surfaces to be joined. Use sparingly. Do NOT spread. (Note: One drop covers an area 25mm x 25mm)KEEP FINGERS AWAY FROM EXCESS ADHESIVE SO THEY WILL NOT STICK TOGETHER. Quickly align both surfaces and apply slight pressure to ensure effective spreading and bond. Should you fail to align the surfaces correctly, do not attempt to re-align them and bond together again. Keep apart and completely clean the surfaces (with acetone or nail polish remover). When dry, re-apply adhesive, re-align and bond again. (Please Note: NOT ALL Nail Polish Removers are ACETONE.) Although the adhesive will grab after several minutes to provide sufficient bond strength for practical use, maximum bond strength is achieved after 12 hours. Wipe tip of tube and replace cap. Handy tips Once open, Supa Glue has a limited shelf life (i.e. up to 1 year provided the tip is wiped clean and the cap replaced securely after each use). Supa Glue vapour can produce a whitening effect in enclosed spaces. To avoid this use in well ventilated areas. The whitening effect can be removed by wiping with acetone (first check that the acetone will not damage the surface). To remove from materials, it is recommended that the material be soaked in a solution of acetone and water (i.e. 3 parts acetone to 1 part water). Note: This method should only be used for substrates NOT adversely affected by exposure to solvents. Check a small area before use. Storing in a refrigerator can reduce the risk of hardening in the tube. Also leaving a pin stuck in the (cleaned) nozzle during storage can reduce the risk of the nozzle becoming clogged with cured adhesive which is difficult to clear. One drop covers an area 25mm x 25mm Supa glues cure more slowly when large amounts are used. For faster cure use sparingly. Since Supa Glue cures with moisture set times may be extended on very dry surfaces or under dry conditions. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Avoid contact with skin and eyes and avoid breathing its vapour. Supa Glue bonds on contact. Should fingers stick together, apply a solvent such as acetone to contact areas, then wash skin with water. Do NOT use solvents in contact with eyes or open wounds. In case of eye contact, immediately flush with water and seek medical attention. When removing Supa Glue from the skin, it is recommended that the skin be soaked in warm to hot water to allow easy removal. It is not advisable to try to remove the cured adhesive by pulling and scraping the skin as this will only serve to damage the skin. If poisoning occurs, seek medical attention. Cured material is considered to be non-hazardous. For further information refer to the Material Safety Data Sheet (MSDS), which can be found at this site. Storage and re-use Ensure cap is replaced and store in a cool dry place. Do not squeeze tube before removing cap. Handle tube by plastic nozzle neck when opening and closing cap. This prevents pressurizing tube which may force material into cap, preventing a tight seal after use. For best performance from this product after opening, store in the refrigerator or in a cool, dry place away from direct sunlight.
$15.00
Selleys All Clear is a multi-purpose sealant that provides long-lasting protection. All Clear is the solution to water leakage and seepage around the home. Best for : Metal, Timber, Glass, Glazed tiles, Brick, Stone, Many plastics (may damage polystyrene and polycarbonate) Features Works on wet, oily, and dirty surfaces* Crystal clear finish Paintable Mould and mildew resistant Water-resistant Strong adhesion Where can this product be used? Sky lights Windows frames and glazing Roof and gutters Sealing metal or PVC guttering and down pipes Air conditioners' enteries Sealing metal or PVC guttering and down pipes Shower screens Sinks and basins Sealing leaks in caravans and recreation vehicles What materials is this product suitable for? Metal Timber Glass Glazed tiles Brick Stone Many plastics (may damage polystyrene and polycarbonate) Use only in a well-ventilated area. Avoid contact with skin and eyes and breathing vapours. The surface must be free from dust, loose particles, and soap residue. If required, clean with turps. Porous surfaces must be dry. Cut cartridge, fit nozzle, and cut to size. Insert the cartridge into a caulking gun such as SELLEYS LIGHT SPEED Caulking gun. Apply with a caulking gun, forcing product into the gap. Press into cracks or surface by pushing sealant ahead of nozzle. Smooth sealant surface immediately with tool dipped in turps. Limitations: May damage some plastics e.g. polystyrene and polycarbonate. Not for permanent water immersion e.g fish tanks Not suitable for use over silicones Not suitable for polystyrene foam *Wet Surfaces: Can be applied to clean, wet non-porous surfaces e.g. metals, glass, glazed tiles – not wet porous surfaces e.g. concrete, timber. Remove as much water as possible, preferably with acetone. Keep nozzle close to surface so sealant contacts surface immediately. Flatten immediately into joints. Adhesion improves on drying. Skins immediately, maximum toughness achieved over several days. Paintable immediately with water-based paints. For oil-based paints undercoat first with a water-based paint. Store in cool dry conditions, below 30°C
$16.93
Selleys 655 FC Crystal Clear Flexible Adhesive and Sealant 290 mL Premium 100 percent crystal clear hybrid adhesive and sealant that delivers superior strength, instant grab, and long lasting flexibility. Bonds and seals on most common building materials, works indoors and outdoors, and can be applied to wet or damp surfaces. Low VOC, non yellowing, paintable, and non slumping for neat vertical and overhead joints up to 20 mm. Why you will love it Superior strength with instant grab Primerless adhesion on most surfaces Applies to wet or damp substrates Fast curing with non slumping finish Crystal clear appearance that stays clear Low VOC and isocyanate free Paintable with water based paints Suitable for interior and exterior use Where it works Ideal for sealing, bonding, and filling on concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, fiberglass, and most plastics. Not recommended for polyethylene, polypropylene, or PTFE. Typical applications Clear sealing of kitchen and laundry splashbacks Bonding trims, panels, and skirtings Sealing gaps in windows, door frames, and cladding General construction and maintenance sealing where a clear finish is desired How to use Prepare the surface so it is clean and free from dust, grease, and loose material. Cut cartridge tip, attach nozzle, and load into a caulking gun. Cut nozzle to the required bead size. Apply a continuous bead, pressing firmly so the product contacts both sides of the joint. Tool with a soapy solution before skinning. For neat edges, mask before applying and remove tape before skin forms. Clean up Uncured product cleans off with mineral turps. Once cured, remove by scraping or sanding. A dedicated silicone and adhesive remover can assist. Good to know Do not paint with solvent based paints. If painting, first coat with a water based paint. Not suitable for permanent water immersion or below water line use. Store below 30°C. Use within 6 months after opening for best results. Specifications Technology Moisture curing silyl modified polymer Colour Clear Pack size 290 mL cartridge Density Approx. 1.06 g/mL Application temperature 5 to 35°C Tooling time at 23°C and 50 percent RH About 25 minutes Skin time at 23°C and 50 percent RH About 45 to 55 minutes Cure rate at 23°C and 50 percent RH Approx. 3 mm per 24 hours Slump 0 mm Tensile strength About 1 MPa Shore A hardness 30 ± 5 Elongation at break Approx. 130 percent Modulus at 100 percent elongation About 1.0 MPa Service temperature 0 to 70°C VOC content Approx. 35 g/L Safety Follow good ventilation and hygiene practices. Refer to the product safety data sheet for detailed advice.
$20.00
Easily mount signs, plaques or house numbers using the Scotch™ Mounting Strips. They are weather resistant and can be used both indoor and outside. Your solution for a long lasting strong bond. Holds up to 2.7kg, 7.6cm holds 340g Mount a sign, mailbox or plaque without needing to use nails or screws Ideal for Indoor and Outdoor surfaces and applications Recommended Surfaces: Painted wood, painted bricks, metal, vinyl Uses 3M VHB™ Tape Specifications Brand Scotch™ Indoor/Outdoor Both Overall Length (Metric) 2.5 cm Overall Width (Metric) 7.6 cm Product Colour Black Product Type Strips Size 2.5cm x 7.6cm
$8.81
![Scotch 3M Mount Double Sided Squares Indoor 15lb x 48 [2.54cm x 2.54cm]](http://gluesaustralia.com.au/cdn/shop/files/051131769960N_f18dde17-9448-4437-aace-df5695c465e8.jpg?v=1754711993&width=645)
Scotch Indoor Double-Sided Mounting Squares are ideal for painted surfaces and allow you to quickly and easily beautify and organize your space. Whether you’re creating a gallery wall or affixing the family chore chart, these permanent double-sided foam squares hold up to 15 pounds and deliver a strong bond every time because of their 3M™ industrial strength adhesive. Your work is up and ready to admire in 30 seconds flat – no nails or hammer needed. Never let how you’re going to hang it get in the way of your creativity with the powerful adhesion of Scotch Indoor Double- Sided Mounting Squares. Ideal for Painted Surfaces Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 3 squares To hold 15 lb use 45 squares Designed For: Painted Drywall, Finished Wood, Metal, Acrylic, Tile and Glass Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in the USA with Globally Sourced Materials Color: White Specifications Size (Imperial) 0.5 in x 0.5 in, 1 in x 1 in
$8.89
Bonds most materials within 30 seconds The level of liquidity and lack of viscosity work best for applications where flexibility and seeping is required 25ml container Integrated nozzle for easy application Ritetite Turbo is a one-component liquid super glue that bonds extremely quickly. When it comes into contact with surface moisture, it hardens instantly. Its extremely fast curing qualities make it an excellent choice for high-speed industrial production, where an ultra-rapid-acting adhesive with low consistency and viscosity is required. Surface Preparation prior to bonding with RITETITE TURBO Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE TURBO Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$23.54
Bonds most materials within 30 seconds High-viscosity allows for greater accuracy and detail Large 100ml container Integrated nozzle for easy application Ritetite Control is a one-component gel super glue that bonds extremely quickly. It’s made with a specially designed thixotropic formula that instantly polymerises (hardens) by absorbing surface moisture. Its fast-curing properties make it an excellent choice for high-speed industrial applications that require a gel-like, viscous adhesive that does not spread or leak like traditional super glue. Ritetite Control works exceptionally well in poor-fitting applications such as rough metal or ceramic repairs, unfinished metal-to-metal bonding, and metal-to-rubber bonding due to its thick gel consistency. Surface Preparation prior to bonding with RITETITE CONTROL Surfaces should be clean, dry and grease-free before applying the adhesive. Use a suitable solvent (such as acetone or isopropanol) for the degreasing of surfaces. Some metals such as aluminum, copper and its alloys will benefit from light abrasion with emery cloth (or similar), to remove the oxide layer. RITETITE CONTROL Directions for use. 1) Apply the adhesive sparingly to one surface. 2) Then, bring the components together quickly and correctly aligned. 3) Apply sufficient pressure to ensure the adhesive spreads into a thin film. 4) Do not disturb or re-align until sufficient strength is achieved, normally in a few seconds. 5) Remove any surplus adhesive solvent, nitromethane, or acetone. NB: For difficult or porous surfaces using a RITETITE activator is recommended. If bonding polypropylene, polyethylene, PTFE or silicone, prime first with a suitable primer. For more information, download the Technical Data Sheet.
$54.39
You have seen 96 out of 153 products
Ultra-fast formulas for quick repairs and close-fit joints. Ideal for small parts, field fixes and production lines with minimal clamping time. Consider gel grades for vertical surfaces and toughened versions for impact resistance. Use filters to refine by chemistry (e.g., cyanoacrylate), viscosity and temperature rating. Always check the product page and TDS/SDS for surface prep and cure guidance.
