Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details
$144.00
Davco PrimeX Multipurpose Acrylic Primer 5L is a professional-grade, water-based primer specially formulated to improve the adhesion of tile adhesives and waterproofing membranes to porous surfaces. Ideal for interior and exterior walls and floors in domestic and commercial applications, this primer ensures strong bonding performance while reducing porosity and dusting of substrates. Surface Preparation: Surfaces must be clean, dry, and free from dust, oil, grease, wax, paint, curing compounds, and other contaminants. Remove any laitance, loose materials, or previous coatings that may interfere with adhesion. On hot or windy days, dampen porous substrates lightly to avoid flash drying—but do not leave standing water. Application Instructions: Stir the primer thoroughly before use. Apply evenly using a roller, brush, broom, or squeegee in a thin, consistent layer. Allow the primer to dry fully before proceeding—drying is complete when the white, milky appearance turns clear. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Typically dries within 30–60 minutes under standard conditions. Cooler temperatures or high humidity may extend drying time. Clean Up: Clean tools and equipment with water immediately after use. Do not allow the product to dry on tools. Technical Data: Type: Acrylic-based Colour: Milky white (dries clear) Suitable for: Cement render, concrete, fibre cement sheets VOC Content: Low Packaging: 5 Litre plastic container
$88.36
Betta Tilecare Wet Area Waterproofer is a flexible, fast-drying, liquid rubber membrane designed for waterproofing internal wet areas such as bathrooms, showers, laundries, and tiled spaces. It provides a durable, seamless moisture barrier that resists water pressure and prevents leaks when applied beneath tiles, screeds, or surface coatings. Surface Preparation: All surfaces must be clean, dry, and structurally sound. Remove dust, oil, grease, wax, and loose or flaking material. Smooth, glossy surfaces should be roughened or etched. Rough or uneven surfaces should be patched and leveled. Mechanically remove any surface contamination or de-bonded coatings for optimal adhesion. Priming (if required): Use a compatible primer on highly porous, glossy, or damp surfaces to promote adhesion. Ensure primed surfaces are dry before applying the membrane. Application Instructions: Apply a bond breaker system such as joint tape or fabric to corners, joints, and penetrations. Apply the first coat using a brush or roller, working it into the surface to avoid pinholes. Allow the first coat to dry (approx. 1 hour), then apply the second coat in the opposite direction. Total coverage should be at least 1.5L/m², forming a final dried film thickness of approximately 1.2mm. Coverage should extend up walls at least 150mm in general areas and 1800mm in shower recesses. Allow the membrane to cure fully before tiling or overcoating. Coverage: Approximately 1.5L per square metre for two coats, depending on surface porosity. Drying Time: Tack-free: 45 minutes Recoat: 1 hour Ready for tiling: 4 hours Flood test ready: 16 hours Dry times may vary based on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based liquid rubber Colour: Grey Finish: Flexible, seamless membrane Dried Film Thickness: Approx. 1.2mm (after two coats) Application Temp: 5°C to 35°C Shelf Life: Refer to packaging for details
$124.03
Betta TileCare Tile & Grout Sealer with Wheel Applicator is a premium, water-based penetrating sealer that forms an invisible moisture-repellent barrier. Ideal for use in bathrooms, kitchens, laundries, and other wet areas, it helps prevent water damage, stains, and mould growth on porous tiles and grout. The included wheel applicator makes sealing fast and easy, delivering smooth and precise coverage with minimal mess. Once cured, it dries clear without leaving a slippery or glossy finish, maintaining the natural look of your surfaces. Surface Preparation Ensure surfaces are clean, dry, and free of mould, soap scum, and any existing sealers or coatings. Remove silicone sealants prior to application. For best results, allow grout and tiles to dry for at least 24 hours before sealing. Heavily porous surfaces may require 3–4 days of drying time. Application Instructions Shake well before use. Starting from the top of the area, apply sealer evenly using the wheel applicator. Ensure all tile and grout lines are thoroughly coated. Allow to absorb for 15 minutes. Reapply a second coat if needed. Wipe away any excess product from tiles with a clean, dry cloth. Avoid heavy foot traffic or moisture exposure for at least 24 hours after final coat. Coverage Approx. 5–10m² per litre depending on tile and grout porosity. Drying Time Touch dry in 15 minutes Fully cured in 24 hours Clean-Up Clean tools and applicator with water immediately after use. Technical Data Appearance: Milky white (dries clear) Base: Water-based penetrating sealer Finish: Invisible, non-slip Application method: Wheel applicator Suitable for: Porous tiles and grout (indoor use)
$21.32
Product Overview: Bastion Multipurpose Primer is a professional-grade waterproofing primer designed for wet areas and tiled surfaces. It enhances adhesion for waterproofing membranes, adhesives, and coatings, making it ideal for use in bathrooms, kitchens, balconies, and other areas exposed to moisture. It is compatible with most construction adhesives and offers rapid drying for faster project completion. Features & Benefits: ✔️ Multipurpose Use – Suitable for internal & external applications on walls and floors ✔️ Enhances Adhesion – Ensures strong bonding for tiles and waterproof membranes ✔️ Rapid Drying – Reduces wait times and speeds up installation ✔️ Low VOC Formula – Environmentally friendly with minimal odour ✔️ High Coverage – Approx. 5m² per litre for cost-effective application Surface Preparation: Ensure surfaces are clean, dry, and free from dust, grease, and other contaminants. Remove loose particles and repair any cracks before application. Porous surfaces may require multiple coats for optimal adhesion. Application Instructions: Shake well before use. Apply using a brush, roller, or spray for even coverage. Allow to dry for approximately 30 minutes before applying waterproofing membranes or adhesives. For highly absorbent surfaces, apply a second coat after the first has dried. Coverage: 1L covers approx. 5m² (depending on surface porosity and application method). Drying Time: Touch dry: 15-30 minutes Ready for membrane or adhesive application: 30-60 minutes Clean-Up: Clean tools immediately with warm, soapy water before the primer dries. Dispose of residue according to local waste disposal regulations. Technical Data: Type: Acrylic-based primer Colour: Milky white (dries clear) VOC Content: Low Application Temperature: +10°C to +35°C Storage: Store in a cool, dry place away from direct sunlight Safety Warnings: Avoid contact with skin and eyes; wear protective gloves and eyewear. Use in a well-ventilated area to prevent inhalation of fumes. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for detailed handling information.
$55.00
You have seen 53 out of 53 products
Roller-grade adhesives for broad, uniform coverage on floors, laminates and panels. Choose the recommended roller nap to achieve the specified spread rate and film thickness; avoid puddling and missed spots. Use filters to refine by chemistry, open time and temperature rating. Always follow the product page and TDS/SDS for prep, application and curing.
