In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dulux Precision Maximum Strength Adhesion Primer
Get a tough, reliable bond on hard to paint surfaces with Dulux Precision Maximum Strength Adhesion Primer. This water based, low odour primer works as a primer, sealer and undercoat, creating a strong foundation for acrylic or oil based topcoats on both interior and exterior projects.
Why choose this primer
Water based with low odour
Excellent adhesion on glossy and hard to coat surfaces
Suitable as primer, sealer and undercoat
Interior and exterior use
Fast drying: touch dry in 30 minutes, recoat in 1 to 2 hours
Topcoat within 30 days for best results
Ideal surfaces
Tiles, high gloss enamels, varnished timber, uPVC, fiberglass, aluminium, galvanised steel, Colorbond, glass, glazed brick, laminates and previously painted glossy finishes.
Key specs
Finish
Flat
Colour
White
Coverage
Up to 10 m² per litre per coat, depending on surface
Dry time
Touch dry 30 minutes
Recoat time
1 to 2 hours
Full strength
7 days after application
VOC
30.4 g/L
Application temperature
Between 10°C and 32°C
Clean up
Water
Pack sizes
1 L and 4 L
How to use
Prepare the surface so it is clean, dry and free of grease, wax, dust, loose paint and rust. Wash if needed and allow to dry.
Stir thoroughly before and during use.
Apply 1 even coat with a high quality brush, roller or spray. For very smooth surfaces 1 coat is usually sufficient.
Allow 1 to 2 hours before recoating or applying the topcoat. Topcoat within 30 days.
Application tips
Do not tint for difficult surfaces. Thin only if necessary with a small amount of water.
When using solvent based enamel topcoats, lightly sand the primer before applying the enamel.
If using under products with strong solvents, let the primer dry 24 hours and test compatibility on a small area first.
Where not to use
Floors, benchtops or surfaces subject to standing water
Below 10°C surface temperature or if conditions may drop below 10°C during drying
Clean up and safety
Clean tools with water and a mild detergent, then rinse. Ensure good ventilation during use. Wear eye protection and avoid skin and eye contact. Always follow label directions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop FC Joint Sealant
Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey.
Why choose this sealant
High flexibility for dynamic joints
Non slump for clean, accurate beads on vertical and horizontal surfaces
Solvent free and isocyanate free
Paintable after curing
Reliable performance supported by a 10 year guarantee
Ideal uses
Joints in fibre cement, blueboard and compressed fibre cement sheets
Facade and cladding joints where movement is expected
General building joints up to 40 mm width
Compatible surfaces
Adheres to most common construction substrates, including:
Fibre cement sheets and blueboard
Precast concrete panels, blockwork and bricks
Sandstone and granite
Fibreglass
Plasterboard
Technical details
Movement capability
± 25%
Joint width
Up to 40 mm
Skin time
Approximately 35 minutes at 23°C and 50% RH
Tack free time
Approximately 1 hour at 23°C and 50% RH
Cure rate
About 2.5 mm per 24 hours at 23°C and 50% RH
Application temperature
10°C to 35°C
Clean up
Warm water immediately after use
Shelf life
12 months unopened, stored cool and dry
Finish
Paintable when dry. Can be overcoated with paint or texture coats.
Colour
Grey
Surface preparation
Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer.
How to apply
Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width.
Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width.
Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides.
Curing times increase in cold or humid conditions.
Safety and handling
Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance.
Guarantee
Backed by a 10 year guarantee when used as directed.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
UNi-PRO Cornice Adhesive 2.5 kg
Overview
UNi-PRO Cornice Adhesive 2.5 kg is a high quality cornice adhesive designed to deliver consistent, reliable bonding performance for trade professionals and serious DIYers. It is formulated for dependable adhesion, easy application, and clean finishing so you can complete jobs with confidence and minimal rework.
Why choose this product
Reliable bond performance supported by proven chemistry and rigorous quality control.
Smooth, predictable application that helps reduce mess and cleanup time.
Versatile adhesion profile suited to a wide range of substrates and project types.
Clear guidance on surface preparation, application method, and curing to help achieve the best possible result.
Suitable for residential fit-outs, maintenance, repairs, and light commercial projects.
Suitable materials
plaster cornice
plasterboard
masonry
Typical applications
General installation, repair, and maintenance where a durable bond is required.
Interior work that benefits from a neat finish and tidy joints.
Projects where dependable initial grab and high final strength are important.
Surface preparation
Ensure all surfaces are clean, sound, and dry. Remove dust, oil, release agents, laitance, and any loose or flaky material. For dense or non-porous surfaces, light abrasion improves key. Test adhesion on a small area if you are unsure about compatibility. Observe local safety requirements when sanding or cutting.
Application
Check ambient and substrate temperature. Apply between 10°C and 30°C in dry, draft free conditions.
Cut the nozzle to the required bead size or prepare the container according to the product type.
Apply an even bead or spread with a suitable trowel where required. Avoid trapping air.
Press the materials together, ensuring full contact. For sheet goods, roll firmly to promote transfer and wetting.
Support, clamp, or brace as needed until the adhesive develops sufficient handling strength.
Cure and working time
Sets firm to hold cornice in place, full cure over 24 hours or as directed. Cooler temperatures and high humidity will slow curing, while warmer, drier conditions accelerate it. Do not load or finish until the bond has developed adequate strength. Always follow best practice for ventilation and safe handling during cure.
Coverage
Coverage varies based on substrate profile, bead size, and installation method. As a guide, a 300 ml cartridge with a 6 mm round bead can lay several linear meters. For trowel applied adhesives, a notched trowel pattern will influence yield. Plan to have extra on hand for porous or uneven surfaces.
Limitations
Do not apply to surfaces that are visibly wet unless the product specifically allows damp application.
Avoid continuous water immersion unless the product is rated for that exposure.
Not all plastics are compatible; test on polypropylene, polyethylene, and PTFE if required.
Observe maximum service temperature and any movement or vibration limits appropriate to the application.
Clean up
Wipe away fresh adhesive with a damp cloth. Scrape away set material carefully. Always read the product label and follow local regulations for disposal of leftover material and containers.
Safety
Read the label before use and keep out of reach of children. Use in a well ventilated area. Wear protective gloves and eye protection. If on skin, wash with soap and water. If in eyes, rinse cautiously and seek medical advice if irritation persists. Do not ingest. Refer to the product Safety Data Sheet for detailed information.
Storage
Store upright in a cool, dry place away from direct sunlight and heat sources. Keep the cap or nozzle tightly closed when not in use. Do not allow to freeze unless the product literature states it is freeze-thaw stable. Rotate stock to use older product first.
Troubleshooting
Poor adhesion: Check surface prep, remove contaminants, and reapply with firm pressure.
Slow cure: Verify temperature and humidity. Increase airflow or allow more time.
Excess squeeze-out: Reduce bead size or spread more evenly. Clean residue before it skins.
Frequently asked questions
Can I paint over it? Many adhesives can be overcoated once cured. Test a small area with your paint system first.
Is it suitable outdoors? Check the product label for outdoor rating. Protect fresh adhesive from rain until cured.
What is the service temperature range? Typical service ranges suit most building environments. Avoid direct flame or extreme heat.
How do I remove cured material? Mechanical methods are usually required. Work carefully to avoid damaging surrounding finishes.
Why buy from Glues Australia
We curate a focused range so you can choose faster and build better. Every product listing includes practical how to detail, compatibility guidance, and straightforward support from a team that understands trade requirements. Order with confidence and get your project moving.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bastion Superlite Lightweight Tile Adhesive 11 kg is a reliable lightweight polymer modified tile adhesive with excellent spread chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 11 kg pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Bastion Superlite for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Bastion Superlite Lightweight Tile Adhesive 11 kg has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Large format wall and floor tiles
Substrates where reduced slump is beneficial
Renovations that require easy trowelling
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Concrete and screeds
Fibre cement sheet
Existing tiles suitably prepared
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of per data on the bag for open time and adjust for ambient conditions. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Observe recommended open time and bed thickness. Allow the adhesive to set before grouting and traffic.
Temperature and environmental performance
Install in mild weather to ensure predictable curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Clean trowels and buckets with water before the mix hardens. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Store the bag sealed in a dry place off the ground. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy.
Why choose Gorilla Ultimate for your next project
Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set.
Best for
Furniture build and repair
Edge bonding and laminations
Cabinetry and joinery where water resistance is valued
Suitable surfaces
The adhesive works well on the following surface types when properly prepared:
Hardwoods and softwoods
Plywood and MDF
Veneers and end grain with correct technique
Surface preparation
Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking.
How to use
Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps.
Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting.
Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady.
Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint.
Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below.
Cure profile
Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured.
Temperature and environmental performance
Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used.
Clean up and finishing
Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour.
Coverage guide
Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes.
Tips for best results
Work within the recommended open time so the adhesive can properly wet the surfaces.
Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength.
For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly.
Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins.
Where movement or vibration is expected, design the joint to share load across a large area.
Troubleshooting
Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary.
Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results.
Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully.
Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats.
Storage and shelf life
Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly.
Safety
Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet.
Frequently asked questions
Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure.
Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance.
Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance.
Planning your job
Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside.
Responsible use
Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework.
Aftercare and maintenance
Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line.
Recycling and disposal
Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A water-based timber and grain filler, suitable for both interior and exterior use. Woodblend sands to an extremely fine, smooth finish. Woodblend can be coated with water or oil-based timber finishes and paints. Available in six inter-mixable colours.
KEY PRODUCT INFORMATIONCoverage: 5m2/LRecoat: 2hrsFull cure: N/AClean up: WaterSheen: N/A
USAGE INSTRUCTIONS
WHERE TO USEAreas: All interior timber, Exterior timberSubstrates: All interior timberLocations: Interior, Exterior
APPLICATIONMethods: Filling blade or knife
1. Apply WoodBlend with a flexible filling blade or knife. Fill deep holes in approx. 10mm stages, allowing two hours drying time between each stage.2. To ease application, dampen blade with water.3. Wipe off excess with a slightly damp sponge. When dry, sand to a smooth finish.4. When using clear finishes, apply WoodBlend after the first coat of clear to minimise smudging.5. For use as a grain filler, thin WoodBlend with 5-10% water to achieve the required consistency. Apply with a flexible filling blade or knife and allow to dry. When dry, sand back to bare timber, leaving filler only in the grain.
IMPORTANT: Keep container tightly closed when not in use.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Weldbond is a universal adhesive for gluing a variety of materials. Wood, tile, glass, plaster, cork, slate, brick, concrete block, linoleum, clay tile, ceramics, fabrics, and more.
About the product
Works as a sealer, bonding agent, or primer
Completely non-toxic
Dries to a clear, flexible bond
Works on porous and non-porous surfaces
UL approved
Will not dissolve hard foam
Safe for Styrofoam
Works well with Plastics and expanded polystyrene
Frequently Asked Questions
Can I keep my weldbond bottle outside in the garage? Will it freeze?
Weldbond should be protected from the cold as it will freeze. Once frozen, this product loses all adhesive capabilities. It should be stored above 50°f/ 10°c at all times. Also, after the container has been opened, ensure it is closed tightly after each use.
What is the shelf life of weldbond?
Weldbond typically has a shelf life of 5 years. If the product is starting to solidify, it can be restored by adding just a little bit of water. We advise the consumer to give the container a good shake prior to every use.
Is weldbond non-toxic?
Weldbond has been tested to be non-toxic. Weldbond conforms to astm d4236.
Is weldbond tested on animals or created with any animal by-products?
Weldbond is not tested on animals and does not contain any animal by-products. This product is vegan-friendly.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Skimming wall board top coat.
Smooth ready to paint surface.
Fine cracks, imperfections and feathering.
Uni-Pro Smooth Coat Filler is the perfect final filler for skimming wallboard and plaster, giving a smooth, ready to paint surface. After base fillers have been applied, Smooth Coat's super fine, creamy texture makes filling fine cracks or surface imperfections easy and skims to a perfect feathered edge. Only a light sanding is required before painting.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ready to use, hard drying acrylic putty filler
Ideal for repairing cracked, broken or uneven surfaces
30 minute fast drying time
Includes bonus applicator
Suitable for fibrous cement, brick, plaster and wood surface repairs
available in 500gm/1.5kg
Not suitable for wet areas or where structural movement occurs
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Our Quick Setting Gel Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product fills gaps and covers large porous surfaces. The final cure colour is cream but can be mixed with paint to colour match. This product sets in only 5 minutes.
Works best on:
• Porous materials
• Ceramic
• Metal
• Pottery
• Wood
• Tile
• Crafts
Properties:
Initial colour: Green resin/white hazy hardener Maximum Gap: .25”
Final colour: White hazy Hardness, Shore D: 75-85 (After full cure)
Set Time: 4-6 minutes @ 65-80F Shear Strength, Steel: 1500 psi (± 20%)
Handling Time: After 1 hour Aluminum: 900 psi (± 20%)
Full Strength: 24 hours Operating Temperature Range:-320 to 3000F (-360 to 1490C)
Instructions:
1. Surfaces should be clean and dry, free from oil and grease.
2. Roughen surfaces with emery cloth or sandpaper for best results.
3. Dispense from container following package directions & mix thoroughly approximately 1 minute. Use package blister or clean cardboard for mixing container, do not use metal.
4. Apply to both surfaces and mate parts together.
5. Remove excess epoxy immediately with denatured alcohol.
6. Sets in 4-6 minutes at room temperature (77F / 25C) with full cure in 24 hours.
Helpful Hints:
To colour Epoxy Gel, do test sample using mixed epoxy with added small amounts of colourant, such as paint (latex or oil), stain or tint. Mix well & apply to scrap piece of wood. Let dry to compare the final colour to the color of repair item. Keep testing until a colour match is achieved, then mix the appropriate amount of colourant with Epoxy Gel and bond repair item.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
The Permanent Patch is a very unique, easy-to-use UV or sunlight activated repair patch. It is fiberglass-reinforced polyester and creates long-lasting repairs. No mixing is required - one step no mess. This incredible permanent patch is waterproof and will not rot or rust. It can be drilled, tapped, sanded and painted in less than an hour. The Permanent Patch makes long lasting repairs on Everything Under The Sun™.
Works best on Aluminum Concrete Drywall Fiberglass Metal Most Plastics Pottery PVC Pipe Rubber Stucco Wood
USE INSTRUCTIONS: NOTE - This product must be exposed to UV sunlight or UV source to cure. Rubber or plastic gloves recommended for sensitive individuals. Not recommended for drinking water applications.
1. Use the Anchor-Tite Patch in a well-ventilated area. Keep the Patch in the black, UV-protected package until you are ready to do a repair.
2. Clean parts to be repaired with soap & water and allow to dry completely. Roughen surface with wire brush or sandpaper.
3. While still in the black UV-protected package, cut the patch material to extend ¾” beyond the repair area using scissors or knife. Remove the white backing and apply cut Patch over repair and press firmly in place. Store unused portion away from sunlight or UV sources. If outside surface is to be painted or finished, remove clear nylon film prior to cure.
4. Expose the bonded Patch to UV sunlight, black lamp or other UV sources until the product is hardened (see approximate times above).
5. After the product is hard and fully cured, it can be drilled, sanded or painted.
6. Wash hands and skin well with soap and water after use.
STORAGE AND SHELF LIFE
Store product sealed in the original black UV-protected package in a cool (<75F), dry location away from UV sources or sunlight. Stored under these conditions, a one-year shelf life can be expected.
SAFETY AND HANDLING PRECAUTIONS
Contains Styrene. Eye, skin & respiratory irritant. Use & store in a well-ventilated area away from heat & sunlight.
Avoid contact with eyes & skin. Do not ingest. Wash hands & skin with soap and water after use. If eye contact occurs, flush with water for 15 minutes & get medical attention. With skin contact, if irritation persists, get medical attention. If swallowed, do not induce vomiting; get immediate medical attention & show container label. KEEP OUT OF REACH OF CHILDREN.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Quick Setting Single Use Epoxy Adhesive is the perfect product to use when you need to get your project pieces in place fast. This product sets in only 5 minutes.
Works best on:
All-Purpose
Ceramic
Metal
Pottery
Wood
Tile
Crafts
Fabric
Properties:
Initial colour: Clear hazy to light
yellow
Final colour: Light yellow
Set Time: 4-6 minutes @ 65-80F
Handling Time: After 30 minutes
Full Strength: 24 hours
Maximum Gap:25"
Hardness, Shore D: 75-83 (After full cure)
Shear Strength, Steel: 1200 psi ( 20%)
Operating Temperature Range: -40o
F to +176oF (-40oC to +80oC)
Instructions:
1. Surfaces should be clean and dry, free of oil and grease.
2. Roughen surfaces with emery cloth or sandpaper for best results.
3. Dispense from containers following package directions and mix thoroughly approximately 1 minute.
4. Apply mixed epoxy to both surfaces and mate parts together.
5. Remove excess epoxy immediately with denatured alcohol.
6. Sets in 4-6 minutes at room temperature (77F or 25C) with full cure in 24 hours.
Storage:
After use, wipe tips to remove residual product and reseal the container. Store upright, with tips up, in a cool, dry location. Stored under these conditions, a one-year shelf life can be expected.
Safety:
Contains Epoxy resin & Mercaptan hardener. May cause eye/skin irritation with direct contact. In case of direct eye contact, flush with water for 15 minutes and consult a physician. Wash hands and skin thoroughly with soap and water after use. If swallowed, seek medical advice immediately and show container label. Keep out of reach of children.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzan's Grip Mega Bond Glue is suitable for bonding a large variety of surfaces in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resistance.
Incredible bond strength
Waterproof
Superior strength
Adheres to even visibly damp surfaces
Fast curing - less than 30 minutes
Materials:
wood, ceramic, stone, concrete, metal, glass, fibreglass, leather, laminate, masonry, plasterboard and some plastics.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Tarzans Grip Mega Bond Glue is suitable for bonding large variety of surfacees in interior and exterior applications. It is formulated to react with moisture on the surfaces to be bonded, resulting in amazing bond strength and water resitance.
Incredible bond strength
Waterproof
Adheres to even visibly damp surfaces
Fast curing - less than 30 minutes
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Multi-purpose adhesive sealant with a wide adhesion range
Sikaflex®-221 is a multi-purpose 1-component polyurethane adhesive / sealant that bonds well to a wide variety of substrates like metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is suitable for making permanent elastic seals.
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
PRODUCT BENEFITS
Bonds well to a wide variety of substrates
Resistant to ageing
Can be sanded and painted
Passes EN45545-2 R1/R7 HL3
Non-corrosive
Low odour
NSF-approved for incidental food contact
Potable water approved (meets AS4020 requirements)
Usage
Sikaflex®-221 bonds well to a wide variety of substrates and is suitable for making permanent elastic seals . Suitable substrate materials are metals, metal primers and paint coatings (2-component systems), ceramic materials and plastics. It is ideally used for internal sealing and simple bonding applications. Seek manufacturer’s advice and perform tests on original substrates before using Sikaflex®-221 on materials prone to stress cracking. This product is suitable for experienced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility.
Surface preparation
Surfaces must be clean, dry and free from grease, oil and dust.
Surface treatment depends on the specific nature of the substrates and is crucial for a long lasting bond. Suggestions for surface preparation may be found on the current edition of the appropriate Sika® Pre-Treatment Chart. Consider that these suggestions are based on experience and have in any case to be verified by tests on original substrates.
Application
Sikaflex®-221 can be processed between 5 °C and 40 °C but changes in reactivity and application properties have to be considered. The optimum temperature for substrate and sealant is between 15 °C and 25 °C.
Sikaflex®-221 can be processed with hand, pneumatic or electric driven piston guns as well as pump equipment. For advice on selecting and setting up a suitable pump system, contact the System Engineering Department of Sika Industry.
Tooling and finishing
Tooling and finishing must be carried out within the skin time of the sealant. It is recommended using Sika® Tooling Agent N. Other finishing agents must be tested for suitability and compatibility prior the use.
Removal
Uncured Sikaflex®-221 can be removed from tools and equipment with Sika® Remover-208 or another suitable solvent. Once cured, the material can only be removed mechanically. Hands and exposed skin have to be washed immediately using hand wipes such as Sika® Cleaner-350H or a suitable industrial hand cleaner and water. Do not use solvents on skin.
Overpainting
Sikaflex®-221 can be painted after formation of a skin. If the paint requires a baking process, best performance is achieved by allowing the sealant to fully cure first. 1C-PUR and 2C-acrylic based paints are usually suitable. All paints have to be tested by carrying preliminary trials under manufacturing conditions. The elasticity of paints is usually lower than of sealants what could lead to cracking of the paint film in the joint area.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER-101 | FINE SURFACE FILLER
Premium, fine surface filler
Very fine consistency for fine surface filling
Application thickness up to 3mm per layer
Fast drying and easy to sand
USE
Suitable for indoor filling work on plaster boards, fabrics, old wallpapers, etc.
Smooth finish
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
COLOUR: White
Appearance / Colour White paste
Packaging 500 ml plastic tube
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion.
Density ~ 1.100 kg/l
Solid Content
~ 55%
Grading Dmax : 0.12 mm
Layer Thickness 3 mm max.
Application Details
Consumption
This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika®
Filler-101 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application
Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-101 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-101 can be applied with spatula in layer thicknesses from 0 - 3 mm. When filling deeper holes or cracks the filler must be applied in several layers and must be allowed to almost dry. Holes and cracks from 4 - 15 mm can more easily be filled with Sika® Filler-105. When dried finish the surface with Sika® Filler-101. Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened / cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: ~ 2 hours
Paintability: ~ 4 hours
Value Base All technical data stated in this Product Data Sheet are based on laboratory tests.
Actual measured data may vary due to circumstances beyond our control.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Sika® Filler One Strike Maxi is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. For filling on plaster, brick, stone, wood and render.
Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application
No sanding or sagging
Fast drying and easy to sand
CHARACTERISTICS AND ADVANTAGES
Fills in one go- No need to build up layers of filler – fills up to 75mm deep in one application
No sanding or sagging
Fast drying and easy to sand
Internal/external use
Overpaintable
Overstainable
Easy to use
Dries brilliant white
COLOUR: White
Sika® Filler One Strike is revolutionary ready-mixed lightweight filler for the preparation of numerous surfaces prior to painting or wallpapering. Based on high strength lightweight polymeric fillers, the product outperforms conventional fillers in most applications
Designed for professional and D.I.Y use.
Uses
Sika® Filler One Strike 1 is suitable for filling of gap in:
Plaster
Brick
Stone
Wood
Render
Characteristics
Advantages
Fills in one go- No need to build up layers of filler - fills up to 75mm deep in one application.
Easy to use - lightweight paste is incredibly easy to apply.
No sanding required - finishes to a smooth surface.
No sagging - the lightweight properties of Sika® Filler One Strike prevent sagging even on ceilings.
Non-shrink - will not shrink back whilst drying.
Quick drying - ready to paint/paper in just 30 minutes.
Overpaintable with most solvent based and emulsion paints.
Overstainable
Internal/external use.
Dries brilliant white
Product Data
Appearance / Colour Lightweight brilliant white paste
Packaging 300 ml cartridge
Storage
Storage Conditions /
Shelf-Life
24 months from date of production if stored properly in undamaged and unopened original sealed packaging, in cool and dry conditions. Protect from frost.
Technical Data
Chemical Base Filled water based polymer dispersion.
Density ~ 0.49-053 kg/l
Solid Content ~ 61% (w/w)
pH 8.0 – 9.0
Grading Dmax : 0.12 mm
Layer Thickness Maximum Width: 50 mm
Maximum Fill: 75 mm
System Information
Application Details
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 cartridge of Sika®
Filler One Strike yields 0.3 m
2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +30°C max.
Ambient Temperature
+5°C min. / +30°C max.
Application Instructions
Mixing Sika® Filler One Strike is supplied ready to use - no mixing is required.
Application Method /
Tools
Apply direct from pail with spatula/spreader. Smooth over surface and allow drying. Sanding is not normally required although the product may be sanded if required.
Sika® Filler One Strike can be painted over after approx. 30 minutes using water based paints. Leave to dry for 12 hours when using solvent based paints. Cleaning of Tools Clean all tools and application equipment with water immediately after use.
Hardened / cured material can only be mechanically removed.
Waiting Time /
Overcoating
Drying Time:
Note:
~ 30 minutes at 20°C
The drying time correspond to thin layer thickness. If deep holes or cracks are filled, longer time is required in order for the product to harden in its full thickness.
Notes on Application /
Limitations
• Do not use to fill plastic or metals.
• Do not apply when rain is imminent (external use).
• Do not apply in temperatures (ambient and surface) below 5°C.
• If using externally overpainting is essential
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Packaging 500 ml plastic tube
5 l and 10 l plastic pail
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SIKA® FILLER 107 | PLASTER FILLER
Premium, wet area, fine surface filler
Fine surface filler that will not rehydrate in humid conditions such as kitchens and bathrooms
Application thickness up to 4mm per layer
Suitable for use in exterior situations when overpainted
USE
Sika® Filler 107 is suitable for interior surface filling work on plaster, woven fabrics, old wallpapers, etc. in wet environments such as kitchens and bathrooms etc.
CHARACTERISTICS AND ADVANTAGES
Ready to use, no mixing required
Easy application
High initial tack or grab on plaster and concrete
Quick drying
Not sensitive to moisture
Appearance / Colours Grey / blue, grey paste
Storage
Storage Conditions / Shelf-Life
12 months from date of production if stored properly in undamaged and unopened original sealed packaging, in dry conditions. Protect from frost.
Technical Data
Chemical Base Filled styrene-acrylate dispersion
Density ~ 1.050 kg/l
Solid Content ~ 62%
Grading Dmax : 0.15 mm
Layer Thickness 4 mm max.
Consumption This depends on the substrate roughness and thickness of the layer applied.
As a guide, ~ 1 l of Sika® Filler-107 can fill ~ 1 m2 per mm thick.
Substrate Quality Clean, free from dust, dry and oil.
Application Conditions / Limitations
Substrate Temperature +5°C min. / +35°C max.
Ambient Temperature +5°C min. / +35°C max.
Application Instructions
Mixing Sika® Filler-107 is supplied ready to use - no mixing is required.
Application Method / Tools
Sika® Filler-107 can be applied with a spatula in layer thicknesses from 0 - 4 mm. When filling deep holes or cracks above 4 mm the filler should be applied in several layers and must be allowed to almost dry before each subsequent layer is applied.
Cleaning of Tools Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be mechanically removed.
Waiting Time / Overcoating
Drying Time: 2 to 4 hours (thicker applications might require longer time)
Paintability: Approx. 12 hours
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Premium, coarse-grained, wide crack filler, Coarse-grained consistency for maximum filling capacity. Application thickness up to 5mm per layer, to a maximum of 30mm. Fast drying and easy to sand
Use:
Suitable for indoor filling and repair where thicker filling capability is needed
A finer grade filler such as Sika® Filler 101 should be used for finishing surfaces before painting
Features
Ready to use, no mixing required
Easy application
Thick layer filling and levelling ability
High initial tack or grab on plaster and concrete
Quick drying
Colour: Grey
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Key Features
Fill cracks and holes in a single application
Pre-mixed and ready to use
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Spakfilla Coloursmart is a ready-mixed, lightweight filler which contains a dry time indicator that goes on pink and dries off-white, taking the guesswork out of knowing when to sand & paint!
Features
Fills cracks and holes in a single application
Pre-mixed and ready to use
Goes on pink and dries off-white when ready to sand
Minimal shrinkage so no need to overfill
Very fast drying allowing sanding and painting in a short time period
Comes complete with a filling spatula for ease of use
Water based, so can be cleaned up with water
Paintable with oil and water based paints
Where can this product be used?
Filling cracks and holes on surfaces where no structural movement occurs
Filling cracks in walls, ceilings, doors, windows
Repairing holes in walls, ceilings, doors and windows
What materials is this product suitable for?
Plaster
Wallboard
Wood
Plasterboard
Masonry
Fibrous cement
Primed nail heads
Size
180g Tub
Colours
Pink, dries off white
Technology
Water Based
Use
Interior
Exterior
Ensure surfaces are clean, dry and free of loose material.
Using the flexible spatula provided on the lid, press the filler firmly into the crack or hole and smooth off surface; there is no need to overfill.
Lightly sand back any excess filler from the surface after product turns off-white (2 hours for holes up to 2mm deep). If more than 2mm deep, or in cold and humid conditions, expect longer drying times.
Dust off any loose dust before painting with water-based paints. For oil-based paints allow 24 hours before painting.
Limitations:
Not recommended for use on plastic, metal or exterior timber likely to swell/shrink on absorption of water.
Product is not flexible so not suitable for use between surfaces that are subject the structural movement - use Selleys No More Gaps
Not recommended for use where load or compression occurs as product may be crushed e.g. behind a door if the knob touches against the wall.
Nailing this product is not recommended.
Avoid using below 5°C or in wet conditions.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys No More Gaps Timber Floors is specifically designed to fill and sealing gaps around and between tongue and groove timber flooring and between other timber panels and fittings where extra flexibility is required.
Features
Superior flexibility and stretch capability to cope with movement
Truly sandable to give a smooth clean finish.
Contains real wood fibre allowing the filler to receive stains better than standard gap fillers
Filler provides an airtight seal, keeping out draughts, dust and pests.
Easy water clean up
Where can this product be used?
For filling and sealing gaps around and between tongue and groove timber floors.
Around and between all types of timber panels and fittings eg. Bedroom and kitchen fittings, benchtops, skirting boards and architraves.
What materials is this product suitable for?
Timber floors
Timber match:
Jarrah - Jarrah, River Red Gum, Karri
Hardwood - Black Butt, Spotted Gum, Brush Box , Tasmanian Oak, Cypress, Beech
Walnut - Ironbark, Teak, Dark stained timbers and engineered floors
Baltic - Pine, Myrtle, Alpine Ash
Size
380g Cartridge
Technology
Water-Based
Use
Interior
How to Use:
The surface to be filled must be clean, dry and free from dust.
Cut seal and nozzle to suit the width of the gap. Fit to the cartridge. Insert into a caulking gun such as Selleys Light Speed Caulking gun.
Apply with a caulking gun, forcing product into the gap.
Press in and smooth off with a spatula. Take care not to drag out applied filler from the gap. Use a spatula to scrape off as much residue as possible from the timber surface, to minimise sanding necessary.
Clean up with a damp cloth immediately.
Allow drying for at least 24 hours before sanding off any residue from the timber surface. Allow longer time in colder weather or if residue left on timber is excessive.
Stain and varnish/paint as desired. Ensure stain/varnish is not allowed to pool in the joint – lightly wipe off while wet if necessary.
Limitations:
Not for exterior use.
Not for gaps greater than 3mm wide in trafficable joints.
Tips:
Ensure sufficient product is applied into the gap if filling tongue and groove overlaps
Coverage: 18 m / 3mm bead
Re-apply filler if timber movement is excessive and movement capability is exceeded, or if a flush fill is desired.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Is a hard setting, thick silver-grey metallic filler, suitable for use with most metals and alloys.
Features
-Repairs and fills
-Sets hard
-Resists boiling water
-Chemical resistant – resists oil and petrol – ideal for engines (but ensure thoroughly hardened before returning petrol to tank)
-Can be sanded and filed for a perfectly smooth finish
-Resistant to water and to hydrocarbon solvents and oils (such as petrol and cooking oils)
-Heat resistant to 100°C
-Can be painted
Where can this product be used?
-Repairs leaks in household utensils, e.g. kettles, holes and cracks in car radiators, pipes etc.
-Metallic Fix may be used to repair holes in petrol tanks if thoroughly hardened before petrol is returned to tank. (Temporary plugs for a leaking tank can be achieved with suitable Knead-It).
-Repairing metal watering can
-Metallic Fix does NOT conduct electricity. It is NOT suitable for electrical applications.
-Metallic Fix will begin to soften above 100°C, therefore, it should not be used to re-affix handles or the like, on cooking utensils; nor to repair holes in pressure vessels such as pressure cookers.
-Not resistant to acetone solvents such as acetone or MEK.
-Do not use where the repair is subject to a breaking strain exceeding 25kg/cm squared.
What materials is this product suitable for?
Iron
Tin
Lead
Silver
Chrome
Zinc
Aluminium
How to use this product
-Remove dirt and grease from the surface to be repaired.
-Remove cap and insert the nail into the nozzle to break the seal.
-Apply pressure on the tube to release cement to the required thickness. Allow to dry for a few hours or overnight (depends on thickness). Remove excess with acetone.
-Sand or file as necessary. Wipe nozzle clean and replace cap after use. Do not use where the repair is subject to a breaking strain exceeding 25kg/cm2.
Handy tips
-Remove excess with acetone
-Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
-Highly flammable.
-Minimise skin contact. Avoid eye contact. If in eyes, hold eyes open, flood with water for at least 15 minutes and see a doctor.
-Intentional misuse by deliberately inhaling the vapours from the product may be harmful or fatal.
Storage and re-use
-Keep container sealed, in a cool place away from ignition sources.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A versatile hand kneadable, fast setting co-extruded epoxy repair system that can be used for repairing a multitude of things. It is especially suitable for application to damp, wet or underwater substrates. It comes in a handy roll form, with the white hardener encapsulated in the aqua green resin part. The product hardens in 20 – 30 minutes after mixing, to a white solid material.
Features
Will not sag, run or drip.
Easy to use – no mess.
Can be drilled, sawed, sanded, filed, tapped, machined or painted one hour after mixing.
Good adhesive strength.
Can be used to reshape, rebuild and repair a multitude of surfaces and applications.
Good gap filling properties.
Long-lasting, durable solution.
Heat resistant to 120°C continuously or 140°C intermittently.
Can be used under fresh or salt water.
Longer set time (less than 20 min).
Suitable for contact with drinking water. Complies with AS/NZS 4020, QAS Type Test Certificate No.: 8649.
Higher tack for underwater repairs.
Where can this product be used?
Creating water features/ attaching pebbles under water in a pond
Sealing holes in foundations and outer walls
Repairing generators, water and fuel pumps
Re-setting ceramic tiles in swimming pools etc
For fast and permanent repairs to damp and wet substrates, and even for underwater repairs
Patching dings, scratches, cuts, gouges and holes in fibreglass, metal and wooden boat decks and hulls
Repair of pipes, fittings, electrical connections, water tanks, tubs, sinks, spas, hot tubs, tanks, pools, leaking gaskets
Forming custom gaskets etc
Ideal for emergency in-water repairs
Repairing fishtanks, ponds, pools
Approval for Drinking Water Contact to AS/’NZ4020:2005, however, limited to maximum surface area: volume ratio of 648 mm2/L; minimum cure time: 72 hours at 20°C; maximum temperature: 85°C; maximum wet film thickness: 5 – 6mm
Not recommended for filling or sealing joints/cracks subject to movement as the cured product is extremely hard and inflexible.
Does not adhere to polyethylene, polypropylene or Polytetrafluoroethylene (Teflon?) or silicone rubber
Set time increases at temperatures below 20°C
Not recommended for use where hydrostatic pressure is present prior to cure
What materials is this product suitable for?
Fibreglass
Wood/Timber
Ceramics
Metal
Concrete
Glass
Most plastics (pre-test required)
Masonry
How to use this product
Clean surface free of grease, dirt and dust. For best results roughen bond area prior to cleaning.
Cut off required amount. Replace disc on the remaining portion. Wear gloves to avoid messing hands. To mix, knead with fingers to a uniform colour. If mixing is difficult, warm to room temperature.
Apply to surface to be repaired (within 12 minutes of mixing) and work the material forcefully into the surface applying pressure until adhesion begins to take effect. Mould to shape if required. If material sticks to fingers, use the plastic wrapper to press the material in place.
For a smooth appearance, remove excess and hand rub with water or damp cloth before hardening begins.
Trim away any excess before initial hardening. Remove any residues with acetone prior to initial hardening. Hardened excess may be sanded or trimmed away once fully cured.
After 20-30 minutes Knead-It Aqua will harden and begin to form a strong bond. Allow for longer cure times at lower temperatures.
After 60 minutes Knead-It Aqua may be drilled, sanded, machined, filed, sawed or painted.
Wash hands thoroughly with soap and water after use.
Handy tips
Ensure the putty and hardener are mixed properly. Knead-It will become warm as it is mixed, A good indication its mixed properly is when you have a uniform colour and feel a mild heat radiating from the knead-it.
To help determine when your knead it has set, keep a small piece off to check- when it is hard, it indicates your job is done.
For best results, use Knead-It Multi-Purpose for applications in contact with drinking water.
Use Knead-It Steel for applications on metal or fuel contact
Store in a cool place for maximum shelf life
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Safety tips
Where possible wear protective gloves when using Knead-It Aqua. Contact with skin may result in irritation. Epoxy resin is a known skin sensitiser. Repeated or prolonged skin contact may lead to allergic contact dermatitis.
If redness or swelling of skin occurs, wash thoroughly with soap and water. Seek medical attention if in any doubt.
Mixed and cured material is not hazardous. Cured material can only be removed by cutting and abrasion. If cured on skin, it will peel off in a few days without assistance. Soaking in warm water will assist removal.
Storage and re-use
Replace siliver disc to seal ends and keep in a cool dry place.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
Selleys Fibreglass Fix Repair Kit is a complete kit containing polyester resin, a hardener and fibreglass mat, for repairs to fibreglass and a variety of other surfaces.
Where can this product be used?
Boat repairs including hull repairs
Surfboard / Surfski repairs
Automotive repairs
Repairing a leaky gutter
Patching downpipes
Patching metal roofs or grass catchers
Not approved for contact with drinking water
What materials is this product suitable for?
Fibreglass
Plywood
Metal
Fibro Sheeting
Most Plastics
How to use this product
Wear rubber or plastic gloves when handling fibreglass
Surface Preparation Surfaces should be clean and dry and free from paint, grease and rust. Cut the fibreglass mat to shape, allowing approximately 3cm overlap all round. Tease out the fibres along the edge of the mat to give a feathered edge.
For wide holes, glue a piece of cardboard to the back of the hole to form a base.
Mixing: For each tablespoon of resin, squeeze 5 drops of hardener from the small tube and mix together thoroughly.
Do not prepare the mixture until required as only a limited time (20 minutes at 20°C) is available before the product gels.
Application Position the mat and apply resin/hardener mixture with a clean, dry brush. Be sure to impregnate the mat completely, working out all air bubbles. Add more mat and resin/hardener mixture to build up or contour the patch as required.
Finishing When the patch has completely hardened, (approximately 1-2 hours, depending on the temperature), it can be sanded to a smooth finish. Fill imperfections with more resin. Paint if required.
Clean up product with Solvent Acetone before it cures
Handy tips
At higher temperatures, the working time decreases.
Can only be tinted with iron oxide or other dry pigments .which must be mixed in very thoroughly.
Surfaces to be joined should be clean and dry.
If recommended amounts of hardener are not used, cure time will vary or an incomplete cure may result.
A useful solvent to clean up epoxy and polyester resins BEFORE they are cured can be prepared by mixing 2 parts toluene with 1 part alcohol (eg methylated spirits or denatured alcohol).
In large amounts, heat can be generated during cure. Care should be taken on heat-sensitive surfaces with large amounts.
Use recommended levels of hardener and resin; variation may result in incomplete cure and variations in cure time.
Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup.
Features
Non-corrosive
Weather resistant – resistant to water, weather or marine growth
Rapid setting
Impact resistant – can take knocks
Sandable – can be sanded after 1-2 hours
Can be painted over
Extended working time – up to 20 minutes at 20°C
Dries Opaque
Heat resistant to 100°C
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SANDING BLOCKS offer optimal sanding results on flat, contoured and irregular shapes.
• Flexible, to conform to contours and irregular shaped objects.
• For sanding and cleaning metal, wood, plaster, plastic, fibreglass etc.
• Can be used for wet or dry sanding.
• Rinse with water to clean.
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-part gap filler and binder for builders and tradesmen that is a safe alternative to the toxic solvent and styrene-based fillers and bogs on the market.
Environmentally friendly and non-hazardous for safe handling and easy transport
Easy to mix, spread on rough and smooth substrates immediately
Rapidly sets in 15 mins (faster in warm weather) with minimal shrinkage
Curing time approximately 60 minutes • Long shelf life when firmly sealed after each use
Once cured it may be chiselled, filed, sawn, planed and sanded into shape
Can also be nailed, drilled, screwed, glued and painted
Highly recommended for waterproofing as gap filler for bathroom renovations and other wet area applications where tiling or painting is required
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Ideal for craft, PREP Plaster of Paris can be used for sculpting, casting, and many other applications.
Once set, it can be sanded, drilled, and chiseled to the required shape and size, then painted and kiln-dried.
Environmentally friendly
Dries white
Dries fast
Very high weather resistance
Unique properties make this product easy to shape and sand
Ideal for schools and craft classes or just having fun!
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Prep Interior & Exterior is a dry, plaster based, cement reinforced filler for the repair of common non-flexible wall linings such as plaster, concrete, timber, and wallboard. This product is highly water-resistant and therefore suitable for interior or exterior use. Can be used to fill deep or shallow crevices in one application.
Easy to mix and use
White finish
Non-shrinking
Easily sanded
Can be nailed or screwed when dry
Water-resistant
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A ready-mixed heavy duty bonded filler for filling holes internally and externally. PREP Multi-Purpose Filler can be used to fill holes in concrete, cement, brickwork, timber and plasterboard, as well as many other porous substrates.
Easy to use
Can be tinted
Ready-mixed
Interior & exterior
Environmentally friendly
Heavy-duty bonded filler
Ideal for floors, walls, ceilings, roofs
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates.
Features Benefits
Water-based Ease of application
Strong Easy spreading
Flexible Time-saving
Water-resistant Easy clean-up
Pre-mixed
Uses
FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards.
Application:
Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system.
Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools.
Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns.
Requires: 2 coats.
Method: Trowel or broad knife.
Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours.
Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask
Sold Out
Express Post: 1-3 Days | Standard Post: 2-5 Days
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates.
Features Benefits
Water-based Ease of application
Strong Easy spreading
Flexible Time-saving
Water-resistant Easy clean-up
Pre-mixed
Uses
FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards.
Application:
Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system.
Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools.
Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns.
Requires: 2 coats.
Method: Trowel or broad knife.
Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours.
Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
FX Super Base Coat X is a revolutionary joint compound. It has remarkable flexibility, minimal shrinkage and extraordinary strength, outperforming current industry leaders’ compounds, both pre-mixed and dry products. * Its flexibility helps with remediation of hairline cracks due to minor structural movement. It is suitable for substrates such as fibre cement sheeting and Magnum Boards. FX Super Base Coat X is part 1 of a high-performance, integrated compound system. Developed by FX Australia and manufactured locally, the use of all products in the Compound System guarantees a time-saving, superior finish and greater strength for substrates.
Features Benefits
Water-based Ease of application
Strong Easy spreading
Flexible Time-saving
Water-resistant Easy clean-up
Pre-mixed
Uses
FX Super Base Coat X is used for fixing fibre cement sheets and Magnum Board joints.
Surface Preparation
All surfaces must be thoroughly cleaned and free of dirt, dust and grease. Substrates need to be constructed or installed to industry/Australian Standards.
Application:
Load FX Super Base Coat X onto hawke using a 150 mm – 200 mm broad knife/trowel and place in to the joint recess, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Next embed fibre-fuse tape into the Compound. Scrape off any excess Compound. Note, for added strength and confidence load FX Super Base Coat X in to the joint recess over the fibrefuse tape, working steadily from one end to the other of the joint recess, ensuring the Compound fills the joint recess and is evenly and smoothly applied. Ensure force is applied to properly embed Compound and fibre-fuse tape into the recess. Allow first coat of FX uper Base Coat X to dry for a minimum of 3–4 hours at 25 °C and 50% humidity. Apply a second coat of FX Super Base Coat X using the same method as the first coat. Ensure the compound is flush with the sheets. Scrape off any excess Compound. Allow to dry for 3–4 hours at 25 °C and 50% humidity before proceeding to product 2, FX Topping Compound X, or proceed straight to water-proofing system or texture-coating system.
Important Note: Clean tools frequently with water and a sponge to stop Compound drying on tools.
Approximate Spreading Rate: N/A. Approximate Film Thickness per coat: Wet: 2000 Microns; Dry: 1500 Microns.
Requires: 2 coats.
Method: Trowel or broad knife.
Drying Times (at 25 °C and 50% humidity): Touch: 1Hour; Recoat: 3–4 Hours.
Note: Do not apply product if the air temperature or substrate temperature is below 12.5 °C or above 35 °C.
The temperature should not fall below 10 °C during the drying process.
Clean-up: Water. Safety: Dust Mask
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
In Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Discover the strength and versatility of FlexiBond Plasterboard Paper Tape, the premier choice for achieving professional-grade, seamless finishes on all your plasterboard projects. Specifically crafted for both the DIY enthusiast and the professional builder, our paper tape is designed to provide unparalleled support and durability to your wall joints and repairs.
FlexiBond Paper Tape stands out with its unique features:
Superior Joint Support: Engineered to reinforce plasterboard joints, preventing cracks and ensuring a durable bond.
Smooth Application: Its fine texture allows for a seamless blend with plaster, resulting in a smooth, invisible finish upon painting or wallpaper application.
Versatile Compatibility: Ideal for use with a wide range of jointing compounds and plaster fillers, FlexiBond adapts to your specific project needs.
Ease of Use: With a design focused on user convenience, our paper tape is easy to cut, apply, and embed into jointing compound, making it suitable for all skill levels.
Whether you’re tackling a minor repair or embarking on a large-scale construction project, FlexiBond Plasterboard Paper Tape is your go-to for achieving flawless walls with lasting integrity.
Fillers and repair compounds that sand smooth for paint-ready results. Choose fast-set for quick turnarounds or extended open time for shaping. Use filters to refine by chemistry and set speed. Always check the product page and TDS/SDS.
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Ash Meranti]](http://gluesaustralia.com.au/cdn/shop/files/9300611329301.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Cypress Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9300611329400.jpg?v=1754724101&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](http://gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](http://gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Ash Meranti]](//gluesaustralia.com.au/cdn/shop/files/9300611329301.jpg?v=1754724101&width=645)
![Intergram WoodBlend Timber Grain Wood Filler 180g [Colour: Cypress Cedar]](//gluesaustralia.com.au/cdn/shop/files/9300611329400.jpg?v=1754724101&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [White]](//gluesaustralia.com.au/cdn/shop/files/4520524003593_20527af7-fe08-426c-ab91-1e7cb16de683.png?v=1754711708&width=645)
![Sika Sikaflex 221 Heavy Duty Adhesive Sealant 310ml [Black]](//gluesaustralia.com.au/cdn/shop/files/4520524003395_211a040d-fd65-46e4-b320-62196c5157c2.png?v=1754711709&width=645)
![Selleys No More Gaps Timber Floors x 380g [Walnut]](//gluesaustralia.com.au/cdn/shop/files/169e8e96732544d89fdb6ec6deaba129.jpg?v=1757753052&width=645)
