Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted.
Recommended on
Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fiberglass composite, china, stone, marble and many rigid plastics
Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete
Properties
High impact resistance
Won’t crack when drilled
Moulds into different shapes
Will fit into any shape of crack
Does not shrink
One-time application
Sandable and paintable
Blends with surroundings
Cures under water
Great for emergency in-water repairs
Step 1: Safety Precautions
Wear gloves.
Step 2: Preparation
Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed.
Step 3: Application
Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted.
Step 4: Cleanup
Cured putty may be cut away with caution using a sharp blade.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted.
Recommended For
Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fibreglass composite, china, stone, marble and many rigid plastics
Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete
Not Recommended For
Potable water systems.
Applications above 121°C (250°F).
Polyethylene and polypropylene.
Structural applications.
Safety Precautions
Wear gloves.
Preparation
Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed.
Application
Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted.
Cleanup
Cured putty may be cut away with caution using a sharp blade.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite® Epoxy Weld Bonding Compound is a two-part system consisting of an epoxy resin and a hardener.
When mixed in equal volumes, the resin and hardener react to quickly produce a tough, rigid, high strength bond. Loctite® Epoxy Weld can be used as a convenient alternative to welding. It can be used as an adhesive for repairing, filling and rebuilding all metal and common surfaces. It cures to a metallic gray finish and can be easily sanded, drilled, machined or painted when fully cured. Loctite® Epoxy Weld does not shrink and is resistant to most shop fluids such as water, diesel fuel, gasoline, antifreeze, hydraulic fluid, motor oil and transmission fluids.
Won t crack when drilled or machined
Can be used outdoors
One-time application
Quick completion of project
Can withstand temperatures up to 350°F (177°C) intermittently
Good for applications requiring shear strength up to 3000 psi
High impact resistance
Water resistant
Does not shrink
Sets in 4 to 6 minutes
High heat resistance
Exceptional bond strength
Recommended on
Repairing machinery, appliances, tools, lawnmowers, automotive components, pipes, and embedding bolts and screws into metal
Bonding various types of metal such as iron, steel, aluminum, brass, bronze, copper and pewter
Properties
High impact resistance
Won’t crack when drilled or machined
Water resistant
Can be used outdoors
Does not shrink
One-time application
Sets in 4 to 6 minutes
Quick completion of project
High heat resistance
Can withstand temperatures up to 350°F (177°C) intermittently
Exceptional bond strength
Good for applications requiring shear strength up to 3000 psi
HOW TO USE:
Step 1: Safety Precautions
Avoid skin contact. Keep away from eyes. Avoid prolonged breathing of vapors. Apply in a well ventilated area. Open windows and doors to achieve good cross-ventilation. Wear safety glasses to protect eyes, and rubber or plastic gloves to protect skin.
Step 2: Preparation
Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Pierce tube nozzles using the reverse side of the caps. Squeeze out equal amounts of resin and hardener on a clean, disposable surface. Prepare only as much as can be used within 3 minutes of mixing. Recap tubes immediately after use. Match the black cap with the resin and the white cap with the hardener. Mix resin and hardener together for approximately 1 minute or until it is uniform in color.
Step 3: Application
Apply to surfaces to be filled or bonded. Join and press parts together. When bonding butt joints, adhesive should be applied as a reinforcing fillet or splint over the joint for additional support. Remove any excess glue immediately with acetone, mineral spirits or rubbing alcohol. Support until bond sets in 10 to 15 minutes at room temperature. Parts can be handled within 15 minutes and machined within 16 to 24 hours. Cure time is lengthened in cooler temperatures and shortened in warmer weather.
Step 4: Cleanup
Clean excess glue immediately with acetone before adhesive sets. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite Marine Epoxy can be applied and cured underwater and eliminates the need to drain out water before repairs. This unique epoxy is a resilient, two-part adhesive system consisting of an epoxy resin and a hardener. When mixed in equal volumes with the convenient dual-syringe applicator, the resin and hardener react to produce a tough, rigid, high strength bond that sets 2 hours and fully cures in 24 hours. Ideal for repairing PVC, copper, brass and galvanized pipes, Loctite Marine Epoxy bonds to metal, concrete, glass, fiberglass, ceramic, wood and certain rigid plastics and cures to a white finish that can be easily sanded or machined. This resilient epoxy does not shrink and is resistant to water, most common solvents, and high impact.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite Pre Mixed Epoxy 60 seconds is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 60 seconds and reaches handling strength in 5 to 10 minutes. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. octite Pre Mixed Epoxy 60 seconds does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled.
Recommended on
Great for crafting projects
Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fiberglass, concrete and stone
Can be combined with fiberglass cloth for a durable patch
Properties
High impact resistance: won’t crack when drilled
Can be tinted to match surrounding materials
Water resistant and can be used outdoors
Does not shrink
Convenient instant mix syringe
Consistently dispenses equal, uniformly mixed amounts of each component
Sets in 40 to 60 seconds
Quick completion of project
HOW TO USE:
Step 1: Safety Precautions
Well-ventilated area, gloves.
Step 2: Preparation
Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from center of plunger. Turn nozzle end up and pull plunger back slightly allowing air bubbles to rise to top. Snap off and discard end of syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place.
Step 3: Application
Depress plunger to dispense equal amounts of hardener and resin directly onto surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it.
Step 4: Cleanup
Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Loctite Epoxy Instant Mix 5 Minute is a two-part adhesive consisting of an epoxy resin and a hardener. When mixed in equal volumes, the resin and hardener react to produce a tough, rigid, high strength bond, which starts to set in 5 minutes and reaches handling strength in 1 hour. The static mix nozzle delivers a uniform mixture of resin and hardener every time. It can be used as an adhesive for a wide range of materials or as a versatile filler for gap bonding, surface repairs and laminating. Loctite Epoxy Instant Mix 5 Minute does not shrink and is resistant to water and most common solvents. It can be tinted with earth pigments, cement or sand for color matching and can be sanded and drilled.
Recommended on:
Bonding metal, glass, ceramic, wood, many rigid plastics, china, tile, fibreglass, concrete and stone
Can be combined with fibreglass cloth for a durable patch
Great for crafting projects
Properties
Will not crack when drilled
Can be tinted to match surrounding materials
Water resistant: can be used outdoors
Does not shrink
One-time application
Convenient instant mix syringe
Consistently dispenses equal, uniformly mixed amounts of each component
Sets in 5 minutes
Quick completion of the project
How to Use:
Step 1: Safety Precautions
Well-ventilated area, gloves.
Step 2: Preparation
Protect work area. Surfaces must be clean, dry and free from oil, wax and paint. For better adhesion, roughen smooth surfaces prior to cleaning. Pre-fit parts to be joined. Remove plastic cap from the centre of the plunger. Turn nozzle end up and pull the plunger back slightly allowing air bubbles to rise to the top. Snap off and discard end of the syringe. Insert nozzle opening and push past prongs. Rotate nozzle 90° to lock into place.
Step 3: Application
Depress plunger to dispense equal amounts of hardener and resin directly onto the surface to be filled or bonded. Remove and discard nozzle. Wipe syringe tip immediately. Retract plunger slightly and close with the cap provided. Place objects together within 40 seconds of adhesive application. Bond sets in 40 to 60 seconds at 20°C to 25°C. Remove any excess adhesive immediately with mineral spirits. Usable strength is obtained within 5 to 10 minutes. Warmer temperatures will shorten the set time and cooler temperatures will lengthen it.
Step 4: Cleanup
Clean excess glue immediately with mineral spirits. Cured adhesive may be cut away with caution using a sharp blade. Prolonged immersion in paint stripper will soften the cured adhesive to aid removal.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
SteelStik is a hand-mixable, steel-reinforced, non-rusting epoxy putty that quickly repairs or rebuilds anything made of metal. After mixing, it forms an industrial-strength polymer compound that can be moulded into shapes or used to build up patch and repair steel components. SteelStik sets in 3-5 minutes and after 60 minutes, can be drilled, tapped, machined, ground, filed and painted. SteelStik cures to a dark grey colour is rated at a tensile strength of 900 PSI and will withstand temperatures up to 300ºF.
GREAT FOR
Automotive & Machine Parts
Exhaust Systems
Plumbing
Stripped Threads
Rust Damage
Household Repairs
STRENGTH 900 PSI
SET TIME 5 Minutes
CURE TIME 1 Hour
CURE COLOR Dark Grey
USE ON
Automotive
Brick
Ceramic
Concrete
Epoxy Putty Sticks
Metal
Under Water/Wet
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey colour. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured.
Great For:
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
Strenght: 3960 PSI
Set Time: 4-6 Hours
Cure Time: 15-24 Hours
Cure Colour: Dark Grey
Use on:
Automotive
Brick
Concrete
Epoxy & Adhesives
J-B Weld
Metal
Pro Sizes
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PlasticWeld is a hand-mixable, fast-setting epoxy putty that forms a durable bond to most major plastic types. *After mixing, it forms a polymer compound that can be moulded or used to build up and repair just about anything made from plastic. When cured, it can be sawed, drilled, carved, sanded and painted. PlasticWeld has a 20-25 minute work life; functional cure occurs in 2-3 hours. PlasticWeld cures to an off-white colour, is rated at a tensile strength of 350 PSI. Does not adhere to polyethylene, polypropylene or some other plastics. Test for adhesion first.
GREAT FOR
Rigid & Semi-flexible Plastic
ABS, PVC & CPVC Pipes
Automotive Trim & Bumpers
Fibreglass Parts
Vinyl Siding
STRENGTH: 350 PSI
SET TIME: 25 Minutes
CURE TIME: 3 Hours
CURE COLOR: Off White
Drinking Water Safe
USE ON
Automotive
Ceramic
Epoxy Putty Sticks
Fiberglass
Plastic/Composite/PVC
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
PlasticBonder™ is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. PlasticBonder™ has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, PlasticBonder™ sets to a tan colour and cures to a hard, permanent bond.
GREAT FOR
Filling Dents
Bumpers
Automotive Trim
Composite Panels
Interior & Exterior Plastic Parts
Fibreglass
USE ON
Automotive
Brick
Ceramic
Concrete
Fibreglass
Plastic/Composite/PVC
Wood
And More
PREPARE
Clean surface area of dirt, grease, oil, paint, or loose debris. For best results use a detergent or degreaser to first clean the surface, then roughen surface with file or coarse sandpaper to provide the best repair.
MIX
After removing the replaceable cap, press down on the plunger and squeeze equal amounts onto a disposable surface and mix thoroughly.
APPLY
Apply with appropriate tool in an even coat, weld bead or extruded shape as needed.
DRY
Sets in 15 minutes. Cures in 30 minutes. If the temperature is below 40ºF, then set time is longer.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Plastic Bonder is a quick-setting, two-part, urethane adhesive system that provides strong and lasting repairs and works on thermoset, carbon fibre composites, thermoplastics, coated metals, concrete & more. Plastic Bonder has a 1:1 mixing ratio, sets in 15 minutes and can be sanded after 30 minutes. With a tensile strength of 3770 PSI, Plastic Bonder sets to a tan colour and cures to a hard, permanent bond.
GREAT FOR
Filling Dents
Bumpers
Automotive Trim
Composite Panels
Interior & Exterior Plastic Parts
Fibreglass
USE ON
Automotive
Brick
Ceramic
Concrete
Epoxy & Adhesives
Fibreglass
Plastic/Composite/PVC
Wood
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
MarineWeld™ is a specially formulated two-part epoxy cold weld system that provides for strong, lasting repairs for bonding different or similar surfaces, such as aluminium, metal, composites, fibreglass and others. MarineWeld™ sets in 4-6 hours at room temperature and is fully cured to a dark grey colour in 15-24 hours. Once cured, it can be shaped, tapped, filed, sanded and drilled and will retain its strength above or below the waters' surface. MarineWeld™ has a 1:1 mixing ratio and tensile strength of 5020 PSI.
GREAT FOR
Boats
Personal Watercraft
In/Outboard Engines
Deck & Hull Accessories
USE ON
Fibreglass
Under Water/Wet
And More
STRENGTH 5020 PSI
SET TIME 4-6 Hours
CURE TIME 15-24 Hours
CURE COLOR Dark Gray
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
KwikWeld™ is a fast-setting version of The Original J-B Weld two-part epoxy cold weld system that provides strong, lasting repairs to metal and multiple other surface types. After mixing, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. KwikWeld™ has a 1:1 mixing ratio, sets in 6 minutes and is fully cured in 4-6 hours. KwikWeld™ cures to a dark grey color, is rated at a tensile strength of 2424 PSI and will withstand temperatures up to 300ºF.
GREAT FOR
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
USE ON
Automotive
Brick
Ceramic
Concrete
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
HighHeat™ is a hand mixable epoxy putty stick specifically formulated to bond and repair materials that will be exposed to high temperatures in automotive and industrial maintenance applications. It cures to a tough, hard bond with little to no shrinkage. This industrial-strength product outperforms conventional epoxy putties at high temperatures and sets in 1 hour at room temperature. After 8 hours, it can be drilled, tapped, machined, ground, filed and painted. HighHeat™ is rated at a tensile strength of 800 PSI and cures to a machine grey in color. It is able to withstand continuous heat exposure of 400ºF and intermittent heat exposure to 550ºF
GREAT FOR
Exhaust Manifolds
Tail Pipes
Mufflers
Engine Blocks
Duct Work
Machinery
High Temperature Projects
USE ON
Automotive
Metal
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
J-B Weld is The Original Cold Weld two-part epoxy system that provides strong, lasting repairs to metal and multiple surfaces. Mixed at a ratio of 1:1, it forms a permanent bond and can be shaped, tapped, filed, sanded and drilled after curing. At room temperature, J-B Weld sets in 4-6 hours to a dark grey color. A full cure is reached in 15-24 hours. J-B Weld has a tensile strength of 3960 PSI and sets to a hard bond overnight. It can withstand temperatures up to 550ºF when fully cured.
Great For:
Household Repairs
Automotive
Plumbing
Marine
Crafts & More
STRENGTH: 3960 PSI
SET TIME: 4-6 Hours
CURE TIME: 15-24 Hours
CURE COLOR: Dark Grey
Use On:
Automotive
Brick
Concrete
Epoxy & Adhesives
Fiberglass
J-B Weld
Metal
And More
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-component epoxy formula highly concentrated with carefully selected pure aluminium particles, modified curing agents, and special high quality additives to provide maximum strength, durability, and ease of application.
APPLICATIONS: ALUMBOND is specially formulated for repairing HVAC copper pipes, HVAC condenser coils, tanks, valves, pumps, castings, water jackets, radiators, etc., where non-rusting, non-magnetic aluminum finish is desired.
PHYSICAL PROPERTIES:
Color Grey
Pot Life 1 lb. @ 24ºC (75°F) 45 minutes
Viscosity Non-sagging Paste
Mixed Viscosity 330,000 cps
Cure Shrinkage 0.0005 in/in
Temperature Resistance 250°F (121ºC)
Hardness (Shore, ASTM D 1706) 83D
Cured Density 17.5 cu. in. per lb.
Coefficient of Thermal Expansion 40 X 10- 6 cm/cm/ºC
Compression Strength (ASTM D 695) 8,600 psi (59 M Pa)
Tensile Strength (ASTM D 638) 3,500 psi (24 M Pa)
Maximum Line Pressure (after 5 hours application time) 650 psi
DIRECTIONS: Surfaces must be clean, dry, and preferably roughened for maximum adhesion.
Dispense equal volumes of resin and hardener. Volume Ratio is 1:1.
Mix thoroughly for 6 minutes making certain that all of the hardener comes in contact with all of the resin.
Apply the mixed compound with a putty knife, spatula, or similar tool. The tool may be moistened with water to provide a smooth finish to the HY-POXY ALUMBOND.
CURING TIME: At 75°F (24°C) a ½” (12.5mm) layer of HY-POXY ALUMBOND putty will be hard in approximately 45 minutes
HY-POXY ALUMBOND will not cure properly below 40°F (4°C).
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions:
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects.
Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes
Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color
Full Cure: 24 Hours
Application
For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.
Clamping
The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.
Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.
Cure Time (amount of time for glue to reach total bonding strength): 24 hours
Clean Up
Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse.
Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.
Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
To remove Gorilla Wood Glue from hands, wash with warm soap and water.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects.
Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes
Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color
Full Cure: 24 Hours
Application
For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.
Clamping
The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.
Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.
Cure Time (amount of time for glue to reach total bonding strength): 24 hours
Clean Up
Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse.
Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.
Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
To remove Gorilla Wood Glue from hands, wash with warm soap and water.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Wood Glue is the adhesive that woodworkers, carpenters and hobbyists trust for their woodworking projects. Gorilla Wood Glue, a PVA glue, offers the benefits of an easy-to-use, water-based adhesive, with the holding power Gorilla is known for. The glue is incredibly water-resistant and dries a natural colour that offers an invisible bond line for your projects.
Clamp Time: 20-30 Minutes // Open Time: 5-10 Minutes
Dry Time: 80% in 1-2 Hours // Dry Color: Natural Wood Color
Full Cure: 24 Hours
Application
For best results, it is essential that the wood surfaces are prepared prior to application of glue. For laminating, the surfaces should be planed smooth, leaving the board surface free from machine marks, tear-out and snipes. Also, be careful to avoid burnishing and end snipes. Just how much Gorilla Wood Glue to apply depends on many factors. In general, apply a generous amount of glue on one of the surfaces. On hard-to-glue woods, apply the glue on both surfaces. Rub together with the other surface to distribute the glue evenly on both surfaces. Enough glue should be applied so that a fine bead of glue squeeze-out will occur when clamping. Coverage: 1 gallon of Gorilla Wood Glue will cover about 200 square feet. 1 fluid ounce will cover approximately 1.6 square feet.
Clamping
The technique and type of clamp to be used are determined by many factors: the specific type of joint, type of stock or lumber, the moisture content of stock, room temperature, assembly time and surface quality. In general, apply enough pressure that will cause a fine bead of glue to squeeze out when the proper pressure is applied.
Clamping Time (amount of time pressure needs to remain applied): 20–30 minutes for room temperature applications. The temperature must be above 55°F. Note that clamping time can be dependent on temperature, humidity, and the porosity of the wood.
Cure Time (amount of time for glue to reach total bonding strength): 24 hours
Clean Up
Clean up while the glue is wet: Use a clean, damp cloth to wipe off excess glue. Make as many passes as needed with the clean area of the cloth to remove all the glue. When areas have completely dried, and as needed. Wash hands, skin and damp cloths with soap and warm water, then rinse.
Clean up when the glue has dried: Use a sharp putty knife, razor, or sharp scraper to shave hardened glue from the surface, then sand as needed. Soak hands and skin in soap and warm water, wash, then rinse.
Cleaning the bottle tip: Use a clean, damp cloth to wipe off excess glue after closing. If tip becomes clogged with dry glue, remove the cap and push the clog backwards with a toothpick, then rinse cap with warm water.
To remove Gorilla Wood Glue from hands, wash with warm soap and water.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla® Super Glue Precise Gel is an easy-to-use, thicker formula* combined with a precision tip and large tube, so it’s easy to apply with control and precision. Great for multiple surfaces and vertical applications.
Directions
1. Protect work area from spills.
2. Clean and dry surfaces to be bonded.
3. To puncture, place cap and nozzle on the tube and tighten down.
4. Apply a small amount of Gorilla® Super Glue Precise Gel to one surface. Only one drop per sq. inch recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond.
5. Press the two surfaces together for about 10-45 seconds. Wait 24 hours for full cure.
6. After using, clean nozzle with a dry cloth and replace the outer cap. Store in a cool, dry place.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Glues Australia presents the Gorilla Super Glue Micro Precise Gel, an innovative adhesive solution tailored for a broad spectrum of applications. This product stands out as a versatile and powerful tool for creating enduring bonds in seconds.
Product Features:
Fast-Acting, Strong Formula: This glue sets in 10-45 seconds, providing a robust and lasting bond quickly.
Controlled, No-Run Gel Formula: Its gel consistency ensures precise application, perfect for vertical surfaces and detailed projects.
Versatile Bonding: Suitable for a variety of materials including plastic*, wood, metal, ceramic, rubber, and more.
Directions for Use:
Surfaces should be dry, clean, and free of dust.
To open, turn the cap clockwise to puncture the seal.
Open the nozzle by turning the green cap counter-clockwise.
Dispense by squeezing, applying a small amount to one surface.
Press surfaces together for 10-45 seconds.
After use, clean the nozzle and store in a cool, dry place.
Technical Specifications:
Application Temperature: Room temperature
Service Temperature Range: -65° to 220° F
Cured Color: Clear
Sandable: Yes
Storage Tips: Store in a cool, dry location away from children and animals.
Frequently Asked Questions:
How does it differ from other Gorilla Glue products? It's a cyanoacrylate adhesive that bonds quickly without moisture or clamp time, unlike polyurethane-based Gorilla Glue.
What is Impact Tough™? A formula designed to withstand bumps and drops, ensuring a strong and resilient bond.
Can it bond all plastics? It is effective on most plastics, but certain types like polyethylene may need special preparation.
How to remove from skin? For spills, immediately wash with soapy water. For cured glue, soak in warm soapy water, then gently wiggle the area.
Is it food safe? It is not intended for any application involving food contact.
Safety Information:
For bonded skin or medical emergencies, contact Australian Poisons Information.
The Gorilla Super Glue Micro Precise Gel is an essential addition to any toolkit. Its combination of strength, versatility, and ease of use makes it an ideal choice for various household and professional tasks. Available now at Glues Australia, it's the perfect solution for your adhesive needs."
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
GORILLA SUPER GLUE GEL
Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time.
PRODUCT FEATURES
NO RUN CONTROL GEL FORMULA
ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use.
IMPACT TOUGH: Increase impact resistance and strength
FAST-SETTING: Dries in 10-45 seconds, no clamping required
VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more!
*Not recommended for use on polyethylene or polypropylene plastic or similar materials.
DIRECTIONS
Protect Work Area From Spills
Clean and Dry Surfaces to Be Bonded
Prepare Gorilla Super Glue Gel
With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle.
Apply Gorilla Super Glue Gel
Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond.
Secure
Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure.
TECHNICAL SPECS
APPLICATION TEMPERATURE – Room temperature
SERVICE TEMPERATURE – -53.9°C to 104.4°C
OUTDOOR – No
PAINTABLE – No
SANDABLE – Yes
STAINABLE – No
EXPANDS WHEN CURED – No
CURED COLOR – Clear
STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator
GAP FILLING – No
FAQS
Why isn’t my bottle of Gorilla Super Glue filled to the top?
For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle.
How is Gorilla Super Glue different than Gorilla Glue?
Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed.
What does Impact Tough mean?
Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond.
Will Gorilla Super Glue bond plastic/vinyl/rubber?
Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds.
How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin?
To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal.
How do I remove Gorilla Super Glue from my surface?
To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first.
Is Gorilla Super Glue food safe?
Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation.
What should I do if I think a human or animal ingested Gorilla Super Glue?
Additional product safety and first aid information can be found here.
How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue?
Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key.
Why do I need to shake and tap the bottle?
Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
GORILLA SUPER GLUE GEL
Gorilla Super Glue Gel is an easy-to-use, thicker and more controlled formula* great for multiple surfaces and vertical applications. Developed for long-lasting repairs in an instant, the clear glue dries in 10–45 seconds. This super glue gel is specially formulated to absorb drops and impacts. Super glue, also referred to as cyanoacrylate glue, or CA glue, works on a variety of materials, including plastic**, metal, stone, ceramic, paper, rubber and more. In addition to its high performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time.
PRODUCT FEATURES
NO RUN CONTROL GEL FORMULA
ANTI CLOG CAP: Keeps glue from drying out, its Gorilla Tough use after use.
IMPACT TOUGH: Increase impact resistance and strength
FAST-SETTING: Dries in 10-45 seconds, no clamping required
VERSATILE: Bonds plastic*, wood, metal, ceramic, rubber, leather, paper and more!
*Not recommended for use on polyethylene or polypropylene plastic or similar materials.
DIRECTIONS
Protect Work Area From Spills
Clean and Dry Surfaces to Be Bonded
Prepare Gorilla Super Glue Gel
With cap on bottle, shake product, then turn product upside down and tap on hard surface to shake gel into bottle nozzle.
Apply Gorilla Super Glue Gel
Remove cap and apply a small amount of Gorilla Super Glue Gel to one surface. Only one dab per 25.4mm x 25.4mm area recommended. Set time can vary based on the amount of glue and type of surface glued. Excess glue can cause delayed or failed bond.
Secure
Press the two surfaces together for about 10–45 seconds. Note that gaps and uneven surfaces may cause delayed bonding. Wait 24 hours for a full cure.
TECHNICAL SPECS
APPLICATION TEMPERATURE – Room temperature
SERVICE TEMPERATURE – -53.9°C to 104.4°C
OUTDOOR – No
PAINTABLE – No
SANDABLE – Yes
STAINABLE – No
EXPANDS WHEN CURED – No
CURED COLOR – Clear
STORAGE TIPS – Store in a cool, dry location. Do not store in refrigerator
GAP FILLING – No
FAQS
Why isn’t my bottle of Gorilla Super Glue filled to the top?
For high performance and usability, the adhesive needs to be protected from air. One way to keep the air out of the adhesive is by packaging in thick plastic bottles. If the thicker plastic bottle was completely full of adhesive, it would be too hard to squeeze the glue out of the bottle.
How is Gorilla Super Glue different than Gorilla Glue?
Gorilla Super Glue is a cyanoacrylate adhesive, while Gorilla Glue is a polyurethane. Unlike Gorilla Glue, Gorilla Super Glue does not require extended clamp time or moisture to activate. It does not foam during set up. In addition, Gorilla Super Glue is recommended primarily for indoor applications only and is ideal for smaller repairs that require an instant bond and projects where clamping is not needed.
What does Impact Tough mean?
Gorilla Super Glue is designed with a reinforced formula to handle bumps and drops with a strong, reliable bond.
Will Gorilla Super Glue bond plastic/vinyl/rubber?
Gorilla Super Glue has been engineered to achieve excellent results on difficult to bond substrates. It is formulated to bond a wide range of similar and dissimilar materials including most plastics, metals, elastomers, wood, and porous surfaces. Gorilla Super Glue requires some absorbed moisture on the bonding surfaces to cure. Certain difficult to bond plastics, such as polyethylene and polypropylene, have little to no moisture and will not form good bonds.
How do I remove Gorilla Super Glue from body/skin or separate bonded body/skin?
To remove Gorilla Super Glue from your skin, soak the bonded area in warm, soapy water. Acetone may also be used according to the solvent manufacturer’s instructions (fingernail polish remover works well). The key is to be patient and NEVER pull the area apart. Gently wiggle the bonded area to allow the soapy water or acetone to penetrate the bond. After soaking, the adhesive should come off easily. Keep in mind that acetone can strip your skin of oils, so apply moisturiser after removal.
How do I remove Gorilla Super Glue from my surface?
To remove uncured Gorilla Super Glue, use a towel dampened with acetone or isopropyl alcohol to blot the area. Several applications may be necessary to completely remove the uncured glue. For removal of cured Gorilla Super Glue from the surface of your project, soak bonded area with warm soapy water or acetone. The adhesive should begin to soften, but many applications may be necessary. Keep in mind that isopropyl alcohol and acetone can damage some surface materials, such as countertops and some plastics. Always test in a small, unseen area first.
Is Gorilla Super Glue food safe?
Gorilla Super Glue is not intended for any application with direct or indirect food contact and should not be stored near food or in the refrigerator. Gorilla Super Glue contains no solvents, but has a strong odor. To avoid irritation, use in areas that have adequate air movement and ventilation.
What should I do if I think a human or animal ingested Gorilla Super Glue?
Additional product safety and first aid information can be found here.
How is Gorilla Super Glue Gel different than liguid Gorilla Super Glue?
Gorilla Super Glue Gel is a thicker and more controllable formula than Gorilla Super Glue. It’s great for projects where precision is key.
Why do I need to shake and tap the bottle?
Since Gorilla Super Glue Gel is a thicker formula than a liquid super glue, shaking the bottle pushes the glue to the tip of the bottle. This allows for an easy and controlled dispensing.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla Super Glue Brush & Nozzle offers 2 easy ways to dispense for control and accuracy. Brush & Nozzle features a precision tip nozzle and fine bristle brush that allow the user to control their super glue application, making it perfect for any project.
Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–45 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear, unlike any other super glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. Super glue, also referred to as cyanoacrylate glue, or CA glue works on a variety of materials, including plastic, metal, fabric, stone, ceramic, paper, rubber and more. It’s Gorilla tough, every time.
Product Features
-Two ways to dispense for greater control and versatility!
-Fine bristle brush for controlled coverage with less mess
-Precision tip nozzle for quick, easy dispensing
-Impact Tough: Unique rubber particles increase impact resistance and strength
-Fast-setting: Dries in 10-45 seconds, no clamping required.
Directions
-Protect Work Area From Spills
-Clean and Dry Surfaces to Be Bonded
-Apply Gorilla Super Glue
-Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch.
-To use the nozzle, unscrew the upper cap and remove. To use the brush, unscrew the full cap and wipe the brush on the inner rim of the bottle to remove excess glue.
Secure
Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time.
Clamp Time: 10-30 Seconds // Open Time: Not Repositionable
Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent
Full Cure: 24 Hours
DIRECTIONS
Protect Work Area From Spills
Clean and Dry Surfaces to Be Bonded
Apply Gorilla Super Glue
Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch.
Secure
Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Its high strength and quick set time make Gorilla Super Glue the go-to for a variety of household projects. Developed for long-lasting repairs in an instant, Gorilla Super Glue dries in 10–30 seconds and is reinforced with rubber for increased impact resistance. We call it Impact-Tough® because it stands up to wear and tear unlike any other instant glue. In addition to its high-performance formula, we’ve added an anti-clog cap with a metal pin inside to ensure an airtight seal for maximum reusability. It’s Gorilla tough, every time.
Clamp Time: 10-30 Seconds // Open Time: Not Repositionable
Dry Time: Light Handling after 1-5 Minutes // Dry Color: Translucent
Full Cure: 24 Hours
DIRECTIONS
Protect Work Area From Spills
Clean and Dry Surfaces to Be Bonded
Apply Gorilla Super Glue
Apply a small amount of Gorilla® Super Glue to one surface. Excess glue can cause delayed or failed bond. One drop covers one square inch.
Secure
Press two surfaces together for 10-30 seconds to achieve bond. Note that gaps and uneven surfaces may cause delayed bonding.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
GorillaWeld is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more!
Features:
INCREDIBLY STRONG: 4250 PSI
STEEL BOND EPOXY
SETS IN 10 MINUTES
WATERPROOF**
FORMS PERMANENT BOND
DRIES DARK GRAY
EASY TO USE
BONDS: Metal, Plastic*, Concrete, PVC, Fiberglass, Ceramic & More!
*Not recommended for use on polyethylene or polypropylene plastics.
**Bonded wood materials should not be submerged or soaked in water.
Directions
All surfaces should be clean and free of debris. To improve adhesion, roughen smooth surfaces with sandpaper before gluing.
Remove cap from each tube and use top of cap to puncture foil seal.
Dispense equal parts from each tube onto a clean, disposable surface.
Mix with disposable mixing tool for approximately 20 seconds until the colour is uniform.
Apply mixture to surface within 3 minutes.
Clamp surfaces together and leave undisturbed for 10 to 30 minutes. Full cure in 24 hours. Cure time dependent on temperature, humidity and quantity applied.
*Note: Not recommended for use on polyethylene, polypropylene or similar plastics.
Specs:
APPLICATION TEMPERATURE: 32°F to 90°F
SERVICE TEMPERATURE: -40°F to 300°F
SET TIME: 10 minutes
CURE MECHANISM: 2 Part Reaction, requires mixing
OUTDOOR: Yes
FREEZE/THAW STABLE: Yes
WATERPROOF: Yes*
PAINTABLE: Yes
SANDABLE: Yes
DRILLABLE: Yes
SHAPEABLE: Yes
STAINABLE: No
CHEMICAL RESISTANT: Limited
EXPANDS WHEN CURED: No
SHRINKS WHEN CURED: No
CURED COLOR: Dark grey
GAP FILLING: Yes
*Not suggested to use on wood materials submerged or soaked in water
Will GorillaWeld bond plastic/vinyl/rubber?
Gorilla Weld will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP), polyethylene (PE) or similar plastics, or any type of rubber with high oil or plasticizer content.
What does GorillaWeld work best for?
GorillaWeld is ideal for metal and plastic (see above) substrates. GorillaWeld does not sag so it is ideal for vertical surfaces
How should GorillaWeld be stored?
GorillaWeld should be stored in a cool, dry place. Store away from children and animals.
How do I mix GorillaWeld?
GorillaWeld should be mixed 1:1 for 20 seconds or until uniform prior to application.
Does GorillaWeld become hot during cure?
Yes, mixing the hardener and resin together creates an exothermic reaction and will generate heat during cure. Consideration should be taken on mixing vessel as not to melt.
How long do I have before GorillaWeld begins to harden?
GorillaWeld will begin to harden after 3 minutes. Adhesive should be applied prior.
What surfaces will GorillaWeld bond to?
GorillaWeld is particularly suited for metal, plastic and other rigid surface bonding.
Is GorillaWeld Food Safe?
GorillaWeld is not recommended for direct or indirect food contact and should not be considered food safe.
Why is GorillaWeld odour so strong?
GorillaWeld is based on methyl methacrylate chemistry which has a naturally strong odour. We suggest using in a well-ventilated area.
How do I remove GorillaWeld from body/skin?
Uncured: GorillaWeld can be harmful through skin absorption and it is strongly recommended that you wear gloves during use. If GorillaWeld is on the skin, try removing with a dry cloth or paper towel and then wash the area thoroughly with soap and water.
Cured: Cured material can be rolled off the skin. Remove as much cured material as possible and wash the area thoroughly with soap and water.
For medical emergencies, call 1-800-420-7186 anytime
How do I remove GorillaWeld from my surface?
Uncured: Wipe up as much material as possible with a dry cloth and clean any remaining product/residue with Isopropyl alcohol (IPA) or acetone following solvent manufacturer’s instructions.
Cured: For removing cured/dried GorillaWeld, mechanical means such as sanding or chiselling.
What should I do if I think a human or animal has ingested GorillaWeld?
For medical emergencies, call 1-800-420-7186 anytime
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
What is the temperature range for applying the glue?
For best results, apply the glue at room temperature.
Original Gorilla Glue should be left out of reach of children and animals.
Can you speed up the curing process?
Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials.
Is Gorilla Glue truly 100% waterproof?
Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II.
How do I extend the shelf life of Gorilla Glue?
Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid.
My bottle of glue has formed a dry layer on top; can I still use it?
Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap.
Do not microwave or heat your bottle of Gorilla Glue to soften the top layer.
How do I clean up Gorilla Glue?
Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper
What is the proper clamp time?
When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight.
What if I don’t have clamps?
Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure.
How much Gorilla Glue should I apply?
Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.
Visit our Gorilla Glue Directions page for more information.
Why do I need to add moisture before gluing with Gorilla Glue?
Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Do I need to prepare the surface first?
Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip.
Is Gorilla Glue really for the Toughest Jobs on Planet Earth?
Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth.
Directions
Prepare and Dampen the Surfaces
If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into.
Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Evenly Apply Gorilla Glue Onto the Dry Surface
Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution.
If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick.
Clamp the Two Surfaces Together Tightly
Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure.
Clean up
If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.
Storage Tips
After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life.
What is the temperature range for applying the glue?
For best results, apply the glue at room temperature.
Original Gorilla Glue should be left out of reach of children and animals.
Can you speed up the curing process?
Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials.
Is Gorilla Glue truly 100% waterproof?
Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II.
How do I extend the shelf life of Gorilla Glue?
Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid.
My bottle of glue has formed a dry layer on top; can I still use it?
Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap.
Do not microwave or heat your bottle of Gorilla Glue to soften the top layer.
How do I clean up Gorilla Glue?
Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper
What is the proper clamp time?
When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight.
What if I don’t have clamps?
Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure.
How much Gorilla Glue should I apply?
Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools.
Visit our Gorilla Glue Directions page for more information.
Why do I need to add moisture before gluing with Gorilla Glue?
Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing.
Do I need to prepare the surface first?
Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip.
Is Gorilla Glue really for the Toughest Jobs on Planet Earth?
Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Gorilla takes epoxy to a new level—the Gorilla Tough level. With its superior solvent and water resistance, Gorilla Epoxy adhesive is incredibly strong and durable for household and automotive repairs alike. The easy-to-use syringe keeps the epoxy resin and hardener separate, so it is easy to dispense and won’t harden over time. The two-part, gap-filling formula easily bonds steel, aluminum, glass, wood, ceramic, tile and most plastics. Plus, it dries in an ideal, crystal-clear finish that makes projects look spotless.
Features:
Dries Clear: Ideal for clean, easy finishing
5 Minute Set: Plenty of repositioning time for the perfect fit.
Gap-Filling: Fills voids and bonds uneven and vertical surfaces.
Water Resistant: Withstands moderate exposure to water
Solvent resistant
Non-Toxic once cured
Easy-to-use syringe: Separate barrels of epoxy resin and hardener keep epoxy from hardening, plus syringe dispenses evenly and includes a cap for multiple uses.
Directions
Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together.
Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded.
Prepare Your Work Area and the Surface
If you’re using Gorilla Epoxy for the first time, or bonding a new type of material, we always recommend trying a test piece first.
Prepare your work area: It is recommended to use Gorilla Epoxy in a well-ventilated area. Be sure your work area is protected from spills. Gather your mixing tray and stir sticks so that all your supplies are together.
Prepare the surface: To improve adhesion, roughen smooth surfaces before gluing. Then clean and dry all surfaces to be bonded.
Mixing Gorilla Epoxy
Remove the black cap from the two syringes. With tip pointing upward, cut or snap the end from tip of the syringes. With the tip still pointing upward, eliminate air and ensure even dispensing by slowly pushing the plunger until both the resin and the hardener are at the tip
Push the plunger to dispense even amounts of resin and hardener onto a clean, disposable, contained surface. The package itself can be used as a mixing tray. If you flip the plastic blister shell over, you can use the small well as a starter dish to begin dispensing until both the resin and hardener are flowing equally. Once the flow is even, move to the larger mixing well to dispense your even ratio.
Mix the two parts for about 20 seconds, until the mixture is uniform. Apply within 5 minutes.As you mix, you will notice that the epoxy warms up. This is a reaction that occurs as the resin and hardener combine.
Application
After mixing is complete, apply Gorilla Epoxy within 5 minutes. The epoxy mixture will continue to thicken and the bond strength will decrease the longer you wait to apply.
Clamping
To reach maximum bond strength, clamp project together and leave undisturbed.
Important Cure Times
Set: 5 minutes to apply and position
Handling: Allow to cure for 30 minutes undisturbed (no weight or handling)
Final Cure: Allow 24 hours for load-bearing weight
Storage: To close, pull plunger slightly back. Wipe tip clean with dry cloth and align notch on tip and cap. Close tightly.
Visit our FAQs for more information on what surfaces Gorilla Epoxy will bond, clean up information and more.
FAQ
Is Gorilla Epoxy gap filling?
Yes. Gorilla Epoxy is gap filling. It will fill voids and bond uneven and vertical surfaces. If filling gaps outdoors, note that Gorilla Epoxy may yellow over time with exposure to sunlight.
What is the shelf life? Are there storage tips to extend the shelf life?
Shelf life for Gorilla Epoxy is a maximum of two years. The adhesive is not activated until the resin and hardener come in contact with one another, so the shelf life is likely to be much longer if the epoxy tip is wiped clean after each use and the cap is securely replaced. Make sure you notice the notch on the cap and be sure to align that with the notch on the syringe tip. This will further ensure the two parts do not accidentally mix.
What is the best application temperature?
For best results, apply in room temperature situations. Application in cold temperatures will slow the cure time of Gorilla Epoxy, while application in hot temperatures can speed up the cure time.
Gorilla Epoxy’s cured bond withstands temperatures ranging from -23° to 82°C
Do I need to use clamps with Gorilla Epoxy? How long?
Clamps are recommended for use during setup to ensure the bond sets correctly.
Set Time: 5 minutes to mix, apply and position
Handling Time: Leave 30 minutes undisturbed (clamping is recommended)
Full Cure Time: 24 hours for load-bearing weight
How much Gorilla Epoxy do I apply?
Gorilla Epoxy is a very strong adhesive. It does not take a lot to get a strong bond.
Average coverage from our 25 mL epoxy syringe will cover 100 square inches.
What can I use as a mixing tray or stir stick?
A mixing tray and stir stick will be included in your Gorilla Epoxy package. Other ideas for mixing trays include aluminum foil trays, cardboard, or paper/plastic plates. Try using popsicle sticks, plastic utensils or straws for mixing.
What is Gorilla Epoxy?
Gorilla Epoxy is a two-part formula that requires equal parts of resin and hardener mixed together for activation. For best strength results, mix a 1-to-1 ratio of resin and hardener. Once mixed, Gorilla Epoxy is capable of bonding many materials and offers high strength results.
How do I remove Gorilla Epoxy?
Gorilla Epoxy is a very strong adhesive and is solvent resistant. Removing dried adhesive is difficult to do. Acetone will soften the epoxy; however, full removal will require mechanical means, such as scraping, rubbing, or sanding.
Uncured Removal:
Skin: Acetone, isopropyl alcohol, 2–3 washings with soap and water. Reminder: Cured glue requires mechanical means, such as rubbing or washing with exfoliating soaps.
Hair: Isopropyl alcohol
Clothes and Carpet: Isopropyl alcohol. For clothes and carpet, avoid acetone, soap and water, and mineral spirits, as they will not work well on fabric.
What surfaces will Gorilla Epoxy bond?
Gorilla Epoxy is very versatile. It boasts high-strength results for steel, wood, aluminum, ceramic, tile, glass, most plastics, pressure-treated lumber and much more!
What surfaces will Gorilla Epoxy bond?
Gorilla Epoxy is water resistant, which means it will resist moderate exposure to water but should not be fully submerged. If you need an adhesive that is 100% waterproof, check out our Original Gorilla Glue®.
How do I dispense Gorilla Epoxy?
Make sure all surfaces are clean, dry and free of oil. To improve adhesion, roughen up smooth surfaces with sandpaper before gluing. Remove black cap from the middle of the plunger. With tip pointing upward, snap end from the tip of the syringe. Slowly push plunger until resin and hardener are at the tip, then dispense evenly. The package blister can be used as a mixing tray. Mix for at least 20 seconds until the mixture is uniform. Apply to surface within 5 minutes. Clamp surfaces together or leave undisturbed for 30 minutes. To close, pull plunger slightly back. Wipe syringe tip with a clean, dry cloth then snap the black cap on tightly.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Overview
Tired of unreliable glues that fall apart? Meet our game-changing Epoxy Adhesive, a powerhouse in bonding technology. In just a single 25mL package, this epoxy adhesive promises unparalleled durability and convenience. It dispenses effortlessly, ensuring a precise ratio for maximum strength. With a fast-acting formula that's perfect for bonding a variety of materials, your DIY or repair projects just became hassle-free!
Features
Automatic Self-Mixing Nozzle
No more guesswork! Our self-mixing nozzle automatically dispenses epoxy and hardener in the exact ratio for optimal performance.
Fast Setting & Long-Lasting
Sets in just 5 minutes.
Can be safely handled within 30 minutes.
Attains full strength after 16 hours.
Versatile Usage
Ideal for bonding ceramics, glass, leather, wood, plastic, and metal. Your go-to solution for a myriad of projects.
Superior Formulation
50% Epoxy Resin
50% Modified Amine
Produces a high-strength bond resistant to temperature fluctuations between -40°C and 80°C.
How to Use
Preparation
Safety First: Always wear protective gloves and safety glasses.
Surface Preparation: Ensure the surface is clean, dry, and free from dust, oil, and grease.
Application
Air Removal: Hold the dispenser, nozzle end up, for 30 seconds to release entrapped air. Cut the tip carefully.
Dispensing: Press the plunger slowly to dispense equal parts of resin and hardener.
Mixing: Mix thoroughly before applying.
Bonding: Apply adhesive to the surface and hold until set. Use tape or clamps if necessary.
Post-Application
Cleanup: Use acetone for cleaning.
Storage: Store in a cool, dry place with the nozzle end up.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
FiberFix Rigid Patch is the other cousin of the Repair Wrap- a fibreglass patch for permanent repairs on flat or hard-to-wrap surfaces. Simply apply the patch over the hole and expose to sunlight or UV light (but don't expose before applying!). In 3-5 minutes after exposure, the patch will cure!
What's Included?: One 3"x3" patch, One 2"x8" patch, One 5"x5" patch
Cure Time: 5-10 minutes (depending on the amount of sunlight/UV exposure)
What Surfaces Will It Work On?: Any rigid surface (will not work on flexible surfaces such as fabrics or highly bendable plastic)
Sandable/Paintable?: Yes!
Applications: Rain gutters, fences, garbage barrels, water tanks, boats, canoes, automotive body, and much more!
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured!
Cure Time: 5-10 minutes (the warmer the water the faster the cure)
Water Pressure Rating: Up to 60 PSI
Temperature Rating: Between -30° F and 300° F
Sandable & Paintable?: Yes!
Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured!
Cure Time: 5-10 minutes (the warmer the water the faster the cure)
Water Pressure Rating: Up to 60 PSI
Temperature Rating: Between -30° F and 300° F
Sandable & Paintable?: Yes!
Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured!
Cure Time: 5-10 minutes (the warmer the water the faster the cure)
Water Pressure Rating: Up to 60 PSI
Temperature Rating: Between -30° F and 300° F
Sandable & Paintable?: Yes!
Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
Dunlop Floor Repairer Rapid Patch Mortar is a high-performance, fast-setting compound ideal for repairing holes, cracks, and uneven surfaces on internal floors. Suitable for use prior to the installation of tiles, vinyl, carpet, or other floor coverings, it delivers a smooth, level finish ready for light foot traffic within 45 minutes and covering applications in as little as 2 hours.
Surface Preparation:
Ensure the substrate is clean, sound, and free of grease, dust, oil, paint, or other contaminants. Surfaces should be dry and firm. Smooth or sealed surfaces must be roughened or etched. For porous substrates like timber, fibre-cement, or plasterboard, priming may be required. For floors in direct contact with soil, a moisture barrier should be used before applying the patch mortar.
Mixing Instructions:
Add 5kg of product into approximately 1.5L of clean water in a clean container. Mix thoroughly with a mixing paddle to a lump-free, smooth consistency. Mix only what can be used within 15 minutes.
Application Instructions:
Apply with a steel trowel to the required thickness (up to 20mm in a single application). Shape and smooth the surface before the material begins to set. For deeper repairs, additional layers can be applied once the initial layer has set. Avoid adding extra water once mixed.
Coverage:
Approximately 3m² at 1mm thickness per 5kg bag. Coverage varies with surface texture and thickness applied.
Drying Time:
Initial set: ~45 minutes
Ready for coverings (tiles, vinyl, carpet): ~2 hours
Final cure: 24 hours (depending on thickness and ambient conditions)
Clean Up:
Clean tools and equipment immediately with water before the mortar sets.
Technical Data:
Type: Rapid-setting cementitious repair mortar
Application Thickness: Up to 20mm
Pot Life: 15 minutes
Foot Traffic: 45 minutes
Ready for Coverings: 2 hours
Colour: Grey
Shelf Life: 12 months in original unopened packaging stored in a dry area
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
Bostik Epoxy Bond is a special two-part adhesive which, when mixed and allowed to set, produces bonds of immense strength. This resin based epoxy sets in approximately 5 minutes to give a permanent and colourless bond. It will adhere to pottery, china, metals, glass, wood, rigid and semi-rigid plastics and cardboard, etc. where an Industrial strength bond is required by handymen, hobbyists and tradesmen.
FEATURES AND BENEFITS
1. Quick setting – will bond in 5 minutes
2. When fully cured, the adhesive can withstand boiling water for short periods of time.
3. Heat resistance rating of 60ºC temperature continuously.
4. Adhesive shear strength of up to 800 psi for metal/metal bonds
APPLICATION
1. Surfaces to be joined must be clean, dry and free from dirt and grease. Metals should be abraded and washed with a petroleum solvent. China and pottery should be washed in detergent, rinsed and dried.
2. Dispense and mix thoroughly, sufficient material of the two parts to carry out the job at hand with a matchstick, screwdriver or similar implement. Reseal the nozzles of the syringe with the enclosed plug and tube with cap and store in an upright position (nozzles upward).
3. Apply a thin film of adhesive to one or both of the surfaces to be joined, press together and do not move until the adhesive has set - usually 5 minutes @ 20ºC. Very good handling strength is obtained after 20 minutes and maximum adhesion is achieved after 24 hours
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
QuikSteel reinforced epoxy putty, 2 ounce
Withstands up to 500 degree Fahrenheit temperatures
Sets in 5 minutes, cures in 1 hour
Hardens like steel, can be drilled, tapped, filed, sanded and painted
Drinking water safe, NSF-61
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
QuikSteel reinforced epoxy putty, 2 ounce
Withstands up to 500 degree Fahrenheit temperatures
Sets in 5 minutes, cures in 1 hour
Hardens like steel, can be drilled, tapped, filed, sanded and painted
Drinking water safe, NSF-61
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength strength after 3 days.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very Strong, durable bonding
Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua)
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Heat Resistant
Clamping is recommended to achieve a stronger bond
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 80°C but strength is regained when temperature drops
Where can this product be used?
Load bearing repairs
Gluing the head back on your hammer
Fixing loose table or chair legs.
Bonding solid pieces of Aluminium sheeting
Bonding timber on your boat
Repairing splits and cracks in Cricket bats
Bonding fibreglass sheets
Repairing Ski’s
Fixing Dynabolts and metal rods into concrete
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics
Crystal
Leather
How to use this product
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately.
When using tubes, Ensure correct caps are replaced on each tube or they will harden
Handy tips
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surfact is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A two-part epoxy adhesive that bonds with maximum strength. Mixed product gels in 2 hours. Initial bonding is achieved in 6-8 hours with maximum bond strength after 3 days.
Features:
-Araldite is stronger than other glues due to the chemical reaction of the two parts
-Bonds a variety of surfaces
-Dries Clear
-Very Strong, durable bonding
-Very high water resistance (e.g. OK for fixing tiles around pool, but not below the water line. For this use Selleys Knead it Aqua)
-Forms a rigid, durable bond
-Can be used for gap filling (surfaces need not mate closely)
-Good chemical resistance
-Heat Resistant
-Clamping is recommended to achieve a stronger bond
-Not suitable for bonding plastics such as Polypropylene and Polyethylene
-Bond strength weakens above 80°C but strength is regained when temperature drops
Appearance:
Translucent
Where can this product be used?
-Load bearing repairs
-Gluing the head back on your hammer
-Fixing loose table or chair legs.
-Bonding solid pieces of Aluminium sheeting
-Bonding timber on your boat
-Repairing splits and cracks in Cricket bats
-Bonding fibreglass sheets
-Repairing Ski’s
-Fixing Dynabolts and metal rods into concrete
What materials is this product suitable for?
-Glass
-Metal
-Wood
-Fabric
-Rigid Plastic – will not bond to Polyethylene or Polypropylene plastics
-Crystal
-Leather
How to use this product
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
-Apply adhesive immediately to both surfaces and press together. Clamping is necessary while bond sets over 6-8 hours. Scrape off excess adhesive and wipe mixing utensils immediately.
Handy tips
-For a maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
-To extend product life replace caps immediately after use. Ensure you wipe excess from the nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
-When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
-Wipe off any uncured Araldite with acetone or nail polish remover.
-To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
-To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. -Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
-Clamping recommended for a stronger bond.
-For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. -Ensure the surface is dry before applying the product.
Safety tips:
-Avoid contact with the skin and eyes.
-Avoid breathing vapour.
-Do not use solvents near eyes or open wounds.
-In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention
-Non-toxic when set.
-For further information refer to the Material Safety Data Sheet (MSDS).
-Storage and re-use
-Ensure caps are replaced and product stored in a cool dry place.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A very fast setting two part epoxy adhesive. Initial bonding achieved in 90 seconds with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Very quick setting in 90 seconds
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling
Good chemical resistance
Where can this product be used?
General small household repairs
Fixing gemstones to mounts
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Most Plastics
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Scrape off excess adhesive and wipe mixing utensils immediately.
Ensure correct caps are replaced on each tube or they will adhere.
Handy tips
Note: For information on how to identify plastics refer to the Selleys plastics guide.
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing cap.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured Araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep a couple at home just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as cold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
In Stock - Ready to ship
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features:
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance:
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product:
General Use
-Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
-All traces of grease, rust paint, etc. should be removed.
-For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
-Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick.
Safety tips:
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
Out Of Stock
Express Post: 1-3 Days | Standard Post: 2-5 Days
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours.
Features
Araldite is stronger than other glues due to the chemical reaction of the two parts
Bonds a variety of surfaces
Dries Clear
Quick setting in 5 minutes
No clamping necessary
Moderate water resistance
Forms a rigid, durable bond
Can be used for gap filling (surfaces need not mate closely)
Good chemical resistance
Appearance
Clear with a slight yellow tinge
Where can this product be used?
Bakelite – joining or repairing
Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots
Repairing splits or cracks in a tennis racket
Repairing metal toys
Not suitable for bonding plastics such as Polypropylene and Polyethylene
Bond strength weakens above 65°C but strength is regained when temperature drops
What materials is this product suitable for?
Glass
Metal
Wood
Fabric
Rigid Plastic
Crystal
Leather
How to use this product
General Use
Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry.
All traces of grease, rust paint, etc. should be removed.
For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning.
Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each
Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately.
When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden.
To use Selleys Araldite Singles:
Fold – the pack in half, so that foil is back to back.
Tear – carefully along perforations.
Squeeze – bubbles to extrude adhesive.
Mix – two parts together until well combined.
Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes.
Handy tips
For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time.
To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps.
When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help)
Wipe off any uncured araldite with acetone or nail polish remover.
To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product.
To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature.
Clamping is recommended for a stronger bond.
Singles are great for those unexpected household breakages, so keep them at home, just in case.
Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up.
For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product.
Safety tips
Avoid contact with the skin and eyes.
Avoid breathing vapour.
Do not use solvents near eyes or open wounds.
In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention.
Non toxic when set.
For further information refer to the Material Safety Data Sheet (MSDS).
Storage and re-use
Ensure caps are replaced and product stored in a cool dry place.
Fillers and repair compounds that sand smooth for paint-ready results. Choose fast-set for quick turnarounds or extended open time for shaping. Use filters to refine by chemistry and set speed. Always check the product page and TDS/SDS.
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](//gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](//gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
