A vinyl reinforced cement-based filler that is water and weather resistant. Matches cement grey when set and easily sands whilst maintaining the strength of cement. Can be nailed and screwed without splitting or breaking. Will not shrink when used in accordance with directions, making it suitable for use in patching steps, paths, paving etc. For use on: Bricks, cement, stone and other masonry surfaces (EXTERIOR). May be used in interior wet areas and as ceramic floor tile cement. Fill depth: Dependent on mix ratio Dries in: 5-6 hours for sanding. Allow 24 hours before painting. Ready to use: NO (mix with water) Available in: 500g & 2kg Colour: Grey and can be tinted by adding cement colorants to the mixing water. Application tips: • Surface to be filled should be clean and dry with no loose or powdery material. Do not wet or prime surfaces before filling. • Coat nail heads with oil based paint prior to filling to prevent rust staining. • Add 4 parts Polyfilla Exterior Powder Filler to 1 part water in a clean container and mix thoroughly into a smooth paste. Use mix within 30 minutes and do not add water to extend working time. • For deeper cracks and holes and on very absorbent surfaces it is advisable to use a slightly stiffer (less water) mix. • Use a clothes peg to reseal the pack. • Press in the mixed filler with a filling knife or trowel and finish with a slightly rounded surface. Where a smooth surface is required, slightly overfill the surface, allow to dry (approx. 5-6 hours), then sand smooth with medium grade sandpaper. • Leave for 24 hours, and then apply a suitable primer/undercoat before painting. • When applying in thin layers, do not over trowel. • Clean up with water before filler dries
$54.08
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Vanilla]](http://gluesaustralia.com.au/cdn/shop/files/9311531002779_4cf84f13-11fd-4024-84f3-8b146caa7d2b.png?v=1754712210&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Light Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002762_be7a4237-355f-47f3-ae09-dabb40913652.png?v=1754712211&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Dark Grey]](http://gluesaustralia.com.au/cdn/shop/files/9311531002755_7e96b58b-9c4a-4693-8cc9-b65123aa898d.jpg?v=1754712213&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Cedar]](http://gluesaustralia.com.au/cdn/shop/files/9311531002731_8a23516e-dc7a-4a74-9fda-5436c7c62091.jpg?v=1754712214&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Brown]](http://gluesaustralia.com.au/cdn/shop/files/9311531002748_2d1b3546-774e-4ede-96e6-fc71fb1dea46.jpg?v=1754712216&width=645)
$11.94
![Poly Coloured Gap Filler Acrylic Sealant Int & Ext [Black]](http://gluesaustralia.com.au/cdn/shop/files/9311531002724_6b56cb9d-718d-4289-8566-b1965f6372f4.webp?v=1754712217&width=645)
$11.94
Permanently joins metals, wood, plastics, ceramics, glass, vulcanized rubber, leather, fabrics, and plaster Pliobond sets fast, is Permanent Stays flexible and won't become brittle
$25.00
A 15-minute, two-part adhesive and filler system that eliminates the need for welding or brazing. It repairs, fills and bonds to iron, steel, brass, bronze, aluminum and copper. Once cured, it can be drilled, tapped, threaded, filed, sanded and painted. Resists most automotive, shop and cleaning fluids. Withstands temperatures to 300°F intermittent. Over 3,000 PSI shear strength on steel. Automobile Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Heavy Duty Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings Marine Suggested Applications: Aluminum, steel, brass, bronze, castings and stampings PRODUCT BENEFITS • No heating required • Holds in 10 minutes • Useable in 30 minutes • Good moisture resistance • Withstands extreme temperatures • Non-flammable TYPICAL APPLICATIONS • Cracked transmission cases • Chipped heads • Rear end castings • Cracked blocks • Cracked intake manifolds • Damaged keyways • Split stampings DIRECTIONS FOR USE 1. Before starting, make sure your work area is protected from accidental spills. Surfaces must be clean, dry and free of grease and oil. 2. Roughen smooth surfaces to be repaired with sandpaper. 3. Apply in ventilated area. Vapors may irritate eyes and nose. 4. Squeeze out equal amounts of bonding agent and curing agent. 5. Mix together thoroughly until color is uniform. 6. Apply immediately to both surfaces and press together. Remove excess glue at once. 7. Allow bond to set for 10 minutes before moving or handling. 8. After 24 hours, typical shear strength on steel is 3000 PSI. 9. Cure time will be slower in colder weather. For Cleanup 1. Cleanup must be completed before curing is complete. Use acetone or mineral spirits for cleanup. 2. Clean hands with Permatex Fast Orange hand cleaners. Chemical / Solvent Resistance The product retains effective properties when in contact with water, oil, fuels, and most solvents. Not recommended for long term exposure to chemicals and solvents. NOTE: Permatex Cold Weld Bonding Compound will not bond polyethylene and polypropylene plastics. GENERAL INFORMATION This product is not recommended for use in pure oxygen and/or oxygen rich systems and should not be selected as an adhesive for chlorine or other strong oxidizing materials. For safe handling information on this product, consult the Material Safety Data Sheet, (MSDS).
$23.00
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$13.90
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$59.90
Nordsjö Professional Fine Filler is an indoor super smooth filler for primed new wood or previously painted clean wooden surfaces and or concrete walls and ceilings. It is ideal for fixing minor imperfections on painted surfaces before repainting. On wood, it is ideal for cracks and joints. For use on interior walls and joinery, including doors, windows, trim, architraves and skirting boards Fill fine cracks up to 2mm, minor blemishes or wood grain for a professional, glass smooth surface for painting Properties Ready to use Sand & paint after 4 hours Super smooth white finish Easy to sand Maximum depth: 2 mm Particle size: Max 0.10 mm How to apply Substrate and crack must be clean, dry and free from loose material. New wood should be primed first. Rub down gloss surfaces for improved adhesion. Metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Apply with a filling knife and spread over the surface, pressing in well. Remove any excess filler and leave to dry. For an even smoother finish rub down with fine sand paper. Use appropriate protection when sanding. Do not apply when the surface temperature is below + 5°C. Replace lid after use. Wash tools with warm water.
$31.11
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls. High performance extra lightweight filler for all general interior and exterior repairs Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials Ideal for over-head applications (non-slump formula) Properties Ready to use Will not shrink or sag Super smooth finish – no sanding required Paintable with all types of paint Maximum layer thickness: 5 cm Maximum depth: 10 cm Easy to apply and shape Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Stir into a smooth paste (if the filler is too dry, just add a few drops of water). Press filler into hole with a filling knife, smoothing off with a wet filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. No sanding is required. If sanding, wait for 24 hours. If painting over with an oil-based finish, wait 14 days. Must be painted over when used outside (minimum 2 coats). Colour: White. Not suitable for drilling. Clean tools and hands immediately after use with warm water. Do not store or use below 5 ° C.
$15.90
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls. High performance extra lightweight filler for all general interior and exterior repairs Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials Ideal for over-head applications (non-slump formula) Properties Ready to use Will not shrink or sag Super smooth finish – no sanding required Paintable with all types of paint Maximum layer thickness: 5 cm Maximum depth: 10 cm Easy to apply and shape Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Stir into a smooth paste (if the filler is too dry, just add a few drops of water). Press filler into hole with a filling knife, smoothing off with a wet filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. No sanding is required. If sanding, wait for 24 hours. If painting over with an oil-based finish, wait 14 days. Must be painted over when used outside (minimum 2 coats). Colour: White. Not suitable for drilling. Clean tools and hands immediately after use with warm water. Do not store or use below 5 ° C.
$12.90
Nordsjö Professional Light and Smooth Super Filler, fills without the need for sanding. Thanks to our unique lightweight technology, our Light and Smooth filler immediately gives you a smooth finish. It does not sag and is easy to model, making it ideal for ceilings and walls. High performance extra lightweight filler for all general interior and exterior repairs Fills deep cracks and holes up to 10cm in plasterboard, wood, fiber cement, concrete, brick and most other common building materials Ideal for over-head applications (non-slump formula) Properties Ready to use Will not shrink or sag Super smooth finish – no sanding required Paintable with all types of paint Maximum layer thickness: 5 cm Maximum depth: 10 cm Easy to apply and shape Quick drying: paint after approx. 2 hours (5 cm layer at 20°C) with water-based paints How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Before application, metal surfaces such as nails and screws should be treated with an appropriate rust resistant primer. Stir into a smooth paste (if the filler is too dry, just add a few drops of water). Press filler into hole with a filling knife, smoothing off with a wet filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. No sanding is required. If sanding, wait for 24 hours. If painting over with an oil-based finish, wait 14 days. Must be painted over when used outside (minimum 2 coats). Colour: White. Not suitable for drilling. Clean tools and hands immediately after use with warm water. Do not store or use below 5 ° C.
$33.35
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$52.31
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$27.90
Nordsjö Professional Super Filler is an ideal product for indoors and outdoors. Effortlessly fills holes up to 10 cm deep. Does not sag, also suitable for vertical and ceiling repairs. You are always assured of a premium result. Fills cracks and holes up to 10cm in brick, stone, wood, fibre cement, render, concrete, polystyrene, plasterboard, plaster and stucco Ideal for over-head applications (non-slump formula) Excellent adhesion to all cementitious surfaces Suitable for interior and exterior applications Not suitable for use on damp surfaces Tools Needed: Filling Knife Properties: Ready to use Will not shrink or sag Easy to sand Accepts nails and screws Paintable after approx. 2 hours (5 cm layer at 20°C) with a water-based paint Sandable after 24 hours Accepts oil-based paints after 48 hours Maximum layer thickness: 5 cm Maximum depth: 10 cm Colour: Light Grey How to Apply: Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix well before use. Product can be used directly from the pot. Apply the product firmly in to the hole with a filling knife. For a super smooth result, finish with a damp filling knife. For holes deeper than 5 cm, apply in layers, with sufficient drying time between the layers. Replace cover sheet after use and ensure lid is properly closed. Once dry sand to a smooth nish. Clean tools with warm water immediately after use. Do not store or use under 5°C.
$160.00
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$13.90
Nordsjö Professional Rapid Repair Filler quickly fills small cracks and holes, such as drill and nail holes. It adheres perfectly to stone, concrete, drywall, plaster and stucco. For filling and repairing small cracks and holes, such as drill holes and nails Excellent adhesion to plasterboard, wood, brick, concrete, fiber cement, drywall, plaster and render Not for use on metal, plastic, PVC and damp surfaces Suitable for interior & exterior use Tools Needed Sharp Knife Fine Sandpaper Properties Ready to use Rapid dry: sand and paint after 15 minutes (5 mm layer at 20°C) with all types of paint Easy to sand Will not shrink Accepts nails and screws Maximum layer thickness: 5 mm Maximum depth: 5 mm Must be painted over when used outside (minimum 2 coats) Colour: White How to apply Substrate must be clean, dry, dust and grease free. Remove all loose materials. Mix the product well before use. Press filler into crack with a filling knife, smoothing off with a wet filling knife. For deeper repairs, build up in layers of 5 mm, letting the product dry in between layers. Remove any excess filler and leave to dry. Once dry sand lightly if required. Clean tools and hands with warm water immediately after use. Do not store or use below 5°C.
$29.00
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$26.67
Nordsjö Professional Flexible Wood Filler repairs small cracks and holes in wood. As the name implies, it is a flexible filling for wood, great for interior and exterior use. Suitable for all types of interior & exterior wood Quick drying, easy to sand Water resistant finish will not shrink, crack or crumble Stainable and paintable Properties Ready for use Excellent adhesion to all types of wood Tough and durable fill that flexes with the natural movement of wood Accepts nails and screws Sandable and paintable after approx. 3 hours (1 cm layer at 20°C) Must be overcoated when used outside (minimum 2 coats) Paintable with all types of paint Maximum layer thickness: 1 cm Maximum depth: 2 cm Colour: natural/pine How to apply Substrate must be clean, dry, dust and grease free. Remove all loose material. Mix the product well before use. Product can be applied directly from the pot. Apply filler firmly into the hole with a filling knife. For a smooth result, finish with a damp filling knife. For deeper repairs, build up in layers of 1cm, letting the product dry in between layers. Once dry, sand the filler so it is even with the surface and dust off. Finish with a stain, varnish or paint. The filler may stain or varnish differently to the surrounding wood. Clean tools with warm water. Do not store or use below 5°C.
$15.50
A transparent polyurethane paste adhesive. SuperGrip 30 Minute is a versatile, ready to use, fast curing, general purpose construction adhesive. Uses Bonding of: • Edge bonding of particle board flooring • Timber & MDF • Marble & Stone • Concrete • Block/blocks • Glass • Fibre cement • Tiles • Rubber • Metals • Aluminium Advantages • 100% waterproof (BS-EN204) • Incredibly strong • Bonds almost anything, including LOSP treated timber • Non drip • No shrinkage • Cures in 30 minutes* • Interior and exterior use • High temperature resistance (minus 30ºC to 100ºC) • Cures transparent • Does not stain Technical Data (Typical) Density: 1.12 g/cm³ Solids content: 100% approximately Cure type: Humidity curing Application temperature: 5ºC to 35ºC Service temperature: -30ºC to +100ºC Relocation time: Approximately 5-10 minutes depending on temperature and ventilation. Cure time: Approximately 30 minutes, depending on temperature, moisture content of surfaces and adhesive thickness. Strength will increase over 24 hours. Flammability: Non flammable
$19.00
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_ad8c4dd8-7138-4341-881e-1e58084dc0c8.png?v=1754716023&width=645)
![Monarch Mini Roof and Gutter Silicone [Black]](http://gluesaustralia.com.au/cdn/shop/files/9320090029257_d1f88907-d8a6-4e7f-b887-a4ac4f2ab20a.png?v=1754716023&width=645)
Monarch Mini Roof & Gutter Silicone is a neutral cure silicone sealant that is ideal for repairing or installing gutters, roofs, downpipes, skylights and more. It can also be used to install metal sheets in the roofing industry and various other building services. With such versatility on offer it's no wonder this product's demand has soared so rapidly! What else would you want from your sealant? Well there are added features like its flexibility and resilience that make it perfect for all applications. You can count on Monarch Mini Roof & Gutter Silicone to stick around because of its long-lasting durability - don't wait until disaster strikes again when you could have had the protection you needed beforehand. FEATURES Premium quality 100% silicone Non-corrosive Neutral cure AS 4020 approved BENEFITS Quick exposure to light running water Suitable for use in all weather UV resistant Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$11.04
Monarch Mini Roof & Gutter Clear Silicone: The Compact Caulking Solution Product Overview Designed for roofing and outdoor applications, the Monarch Mini is perfect for a variety of materials like metal, brick, galvanized iron, tiles, and aluminium. Key Features & Benefits Quick exposure to light running water UV resistant for lasting outdoor use Neutral cure, making it versatile and safe for different materials Non-corrosive and AS 4020 approved Compatible with Monarch Mini Compact Caulking Gun Perfect For Great for small projects where a full-size cartridge is not needed. Ideal for: Repairing gutters Fixing roofs Mending downpipes Tight spaces that traditional cartridges can't reach Colors Available Available in black and translucent versions for versatility in your projects. How To Use Best when used with a Monarch Mini Compact Caulking Gun to reach tight spaces. Always follow the safety guidelines as provided on the product label.
$7.35
LOCTITE® SI 598™ cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. This product resists aging, weathering and thermal cycling without hardening, shrinking or cracking. Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers. This product is typically used in applications with an operating range of -54 °C to 260 °C. Metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. LOCTITE® SI 598 is a metallic black, 1-part, thixotropic, room temperature vulcanizing oxime silicone paste sealant. It cures on exposure to moisture in the air to form a tough, flexible, silicone rubber gasket. It resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. This product is typically used in applications with an operating range of -54 to +260°C. Excellent resistance to automotive motor oils Enhances load bearing & shock absorbing characteristics of the bond area Typical applications include oil pans, transmission pans, valve covers, valves and guides, timing gear covers, and differential covers Technical Information Color Black Fixture Time 30 Fixture Time Temperature 30 °C Physical Form Paste Technology Silicone TYPICAL ENVIRONMENTAL RESISTANCE The product retains effective properties in contact with automotive fluids, such as motor oil, transmission fluids, alcohol and antifreeze solutions. NOTE: Not recommended for parts in contact with gasoline. Directions for use: 1. For best performance bond surfaces should be clean and free from grease. 2. Full performance properties will develop over 72 hours. 3. Moisture curing begins immediately after the product is exposed to the atmosphere, therefore parts to be assembled should be mated within a few minutes after the product is dispensed. 4. Excess material can be easily wiped away with non-polar solvents. NOTE: LOCTITE® SI 598™ is not recommended for use as a cylinder head gasket or head gasket sealant. 5. For full automatic applications a volumetric dispensing system is recommended.
$15.52
Red, 1-part, flowable smooth, acetoxy silicone paste sealant. LOCTITE® SI 596 is a red, 1-part, flowable smooth, acetoxy silicone paste sealant. It forms a tough, flexible, waterproof, oil-resistant silicone rubber bond. It is also used as a sealant and adhesive in industrial furnaces, ovens, boilers, exhaust stacks, high temperature ducting and heating elements in electrical appliances. Resists ageing, weathering and thermal cycling without hardening, shrinking or cracking Typically used in applications with an operating range of -50°C to +250°C Technical Information Colour Red Fixture Time 30 min. Fixture Time Temperature 30 °C Full Cure Temperature 77 °F Mix Ratio No Mix Physical Form Paste Skin Formation Time 8 min. Temperature -75 - 600 °F
$11.83
Hand Cleaner - general purpose. Based on natural extract. Biodegradable. Can be used with or without water. LOCTITE® SF 7850 is a natural hand cleaner containing no petroleum solvents. It cleans hands with a solvent extracted from oranges. This hand cleaner has a citrus scent and contains no artificial fragrance. It is a skin-friendly abrasive lotion that contains aloe vera, lanolin and jojoba oil for skin conditioning. It cleans without water and can remove grease, grime, inks, soil, paint, gasket cements, epoxies and glues. It contains extra-fine abrasives which clean deep into pores. Natural extract base Free of mineral oils Biodegradable Contains premium skin conditioners Works with or without water Removes ground-in dirt, grease, grime, and oil Technical Information Applications Cleaning Hands Key Characteristics Biodegradable, General Purpose
$12.01
Loctite® Repair Putty Multi-Purpose is a two-part adhesive consisting of an epoxy resin putty and a hardener putty which are mixed by kneading. They react to produce a hard, tough, permanent and waterproof bond on a wide range of materials. Loctite® Repair Putty Multi-Purpose does not shrink and is resistant to most common solvents. It can bond to damp surfaces and cure under water. Loctite Epoxy Putty can be sanded, drilled and painted. Recommended on Bonding metal, masonry, brick, wood, glass, ceramic, rubber, fiberglass composite, china, stone, marble and many rigid plastics Use to seal pipes, fix leaks in tanks and drains, repair appliances, tools, furniture, toys, automotive parts, pools and cracks in concrete Properties High impact resistance Won’t crack when drilled Moulds into different shapes Will fit into any shape of crack Does not shrink One-time application Sandable and paintable Blends with surroundings Cures under water Great for emergency in-water repairs Step 1: Safety Precautions Wear gloves. Step 2: Preparation Surfaces should be clean and free from grease and oil. For better adhesion, slightly roughen the surface with a wire brush or sandpaper prior to cleaning. Cut off desired length of Epoxy Putty and knead until uniform color is obtained. Putty turns from blue to white when completely mixed. Step 3: Application Apply the putty to surface to be repaired within 3 minutes of mixing. Work putty firmly into the crack or hole. For bonding, place the putty between the surfaces and apply firm pressure to ensure intimate contact with both surfaces. If applying to a wet surface, apply forcefully and hold in place until adhesion takes effect. For a smooth finish, rub the putty with a damp cloth prior to hardening. Working time is approximately 5 minutes. After 45 minutes, the putty can be sanded, drilled or painted. Step 4: Cleanup Cured putty may be cut away with caution using a sharp blade.
$18.00
LOCTITE® 249 is a blue, dimethacrylate ester acrylic film thread locker. It is supplied in a low tack film to provide a convenient and easy to use package, especially where a liquid product may be too fluid to stay on a part or be difficult to apply. This product can be used for immediate assembly or days later and provide consistent strength on a variety of metal substrates. Dimethacrylate ester acrylic film threadlocker. It is supplied in a low tack film to provide a convenient and easy to use package. Designed for the locking and sealing of threaded fasteners which require normal disassembly with standard hand tools Supplied in a low tack film to provide a convenient and easy to use package Can be used for immediate assembly or days later Provides consistent strength on a variety of metal substrates Technical Information Color Blue Cure Type Activator Cure, Anaerobic Cure Full Cure Temperature 77 °F Key Characteristics No Mix Number of Components 1 Part Physical Form Film Storage Temperature 46 - 69 °F Technology Acrylic Temperature -65 - 300 °F Thread Size (Maximum) R3/4" Torque Break on M10 Steel 74 in./lb. Torque Prevail on M10 Steel 47 in./lb. Viscosity 8700 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$16.08
IMPREGNATED WITH E-POX E RESIN WITHSTANDS HEAT UP TO 260°C Repairs engine exhaust systems of all types of cars, trucks, boats, motorcycles, and stationary engines. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. Wear goggles as eye protection 2. Warm-up muffler, peel back the red overlay on both sides of bandage and then wrap the clear center around the damaged area- overlapping 10-15mm 3. Run the motor or drive for approximately 30 minutes. The heat from the exhaust chemically welds the epoxy in the bandage into one solid protective coating NOTE: For small repairs use Loctite Muffler Putty (MP2). When repairing large holes use a piece of sheet metal ie beer can, wired between the hole and the bandage as reinforcement. When assembling new pipes and mufflers use Loctite Exhaust Joint Sealer (JS1), It guarantees carbon-monoxide leakproof joints For large mufflers more than one bandage may be required
$7.23
$6.94
LOCTITE® MR 5923 is a dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. It seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. Dark reddish-brown, viscous liquid thread sealant with a characteristic alcoholic odor. For close tolerance flanges Slow drying Flexible setting LOCTITE® MR 5923™ seals close-fitting parts, machined surfaces, and threaded connections in industrial, aircraft, and marine applications. It is a slow drying liquid that changes to a pliable, tacky film through solvent evaporation. Typical applications include solid gasket dressing, close-fitting machined surfaces, threaded connections, aviation engines, and marine engines. This product is typically used in applications with an operating range of -54 °C to +204 °C. Technology Solvent-based Chemical Type Modified resin, fillers, and alcohol Appearance Brown liquidLMS Viscosity Flow similar to SAE 10 Motor Oil Cure Air dry Application Gasketing & sealing Specific Benefit ● For close tolerance flanges ● Slow drying ● Flexible setting Chemical/Solvent Resistance LOCTITE® MR 5923™ retains effective properties in contact with water, ethylene glycol, gasoline, motor oil, transmission fluid, and seawater Directions for use: 1. Remove all previous material from mating surfaces. 2. For best results, clean and prep the area with an oil-free solvent. 3. Remove cap. Coat with a brush-top applicator. 4. When used as a gasket dressing, spread product with a spatula to a uniform film on one side of the gasket and then position it on the assembly. Coat the second side of the gasket and re-assemble. Slower drying formula increases work time. 5. Assembly is operational after 4 hours, full cure is effective after 24 hours. 6. The product can be removed from metal surfaces with isopropyl alcohol. If the sealant has been dried for a long time or at high temperatures, cover the sealant with alcohol and allow it to soften overnight.
$6.67
Neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. LOCTITE® MR 5412 is a yellow, neoprene solvent-based contact cement gel used for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding. Typical applications include bonding weather stripping, insulation, rubber and trim to wood and metal. Suitable for all types of weather-stripping, porous and non-porous surfaces and general purpose bonding Technical Information % Solids 10 Agency Approvals / Specifications CFIA Listed Colour Yellow Fixture Time 15 min. Key Characteristics Waterproof Physical Form Liquid Specific Gravity 0.88 g/l Specific Gravity Temperature 25 °C Substrates Metal, Wood Directions for use: 1. Clean surfaces thoroughly. Use abrasives to remove any powdery mold release from new weatherstripping. 2. Apply a thin, even film to both surfaces. 3. Allow to dry tacky (3 to 4 minutes). 4. Bond the two surfaces together and apply enough pressure to produce uniform contact. 5. NOTE: The early strength of LOCTITE® MR 5412 is enough to hold most parts together. However, maximum strength is obtained after the adhesive is completely dry. Aging of the bond and exposure to moderate heat increases strength.
$16.45
Lubricant - emergency repair. Shock freezing (-40°C). Releases rusted, corroded and seized components. Wicks directly into the rust by capillary action. LOCTITE® LB 8040 is a special mineral oil designed to free rusted, corroded and seized parts. The shock-freezing effect will cool parts instantly down to -43 °C and cause microscopic cracks in the layer of rust. This allows the lubricating ingredients to wick directly into the rust by capillary action. The product leaves a thin film on the released parts that lubricates and prevents rust. Universal application Bactericide-free Highly resistant to micro-organisms, bacteria and fungi Excellent cooling and lubrication performance Low foaming
$25.00
White, metal-free, food-grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. H1 NSF Reg. No: 123004. LOCTITE® LB 8014 is a white, metal-free, food grade lubricant and anti-seize made from white oil and extreme pressure (EP) additives. It prevents friction, seizing and galling in stainless steel and other metal parts. It is temperature resistant to +400°C, has a 0 NLGI grade and is H1 NSF Registered; No: 123004. Food grade lubricant and anti-seize Metal-free Temperature resistant to +400°C NLGI Grade 0 Prevents friction, seizing and galling in stainless steel and other metal parts H1 NSF Reg. No.: 123004 LB 8014™ prevents seizing, galling, friction, and wear on threaded joints and other metal-to-metal surfaces. It is a combination of white lubricating solids and extreme pressure lubricating agents in an aluminum gelled white oil. Typical applications include pipe joints, nuts, bolts and studs, flange gaskets, slip-fit, press-fit and keyed shafts, and metal-to-metal contact involving stainless steel and other stainless alloys. It is used in industrial food industries such as meat and poultry packing plants, dairy products processing plants, canning plants, grain processing plants, sugar processing plants, bakeries, beverage plants, breweries, hospitals, and other general plant maintenance. This product is typically used in applications with an operating range of -29 °C to +400 °C. PRODUCT DESCRIPTION characteristics: Technology Anti-Seize Appearance Smooth white paste LMS Components One component - requires no mixing Cure Not applicable Application Lubrication Specific Benefits ● Lubricates, seals, and prevents galling in stainles steel joints and threaded connections ● Temperature resistant to 400 °C ● Metal free formulation Directions For Use: 1. For best performance the mating surface should be clean and free of grease. 2. Apply thin coating to threads and flats of nuts and bolts, assemble. 3. Use full strength. Do not thin.
$44.40
WITHSTANDS HEAT UP TO 550°C Holes in mufflers, tailpipes, and engine pipes can be fixed immediately without dismantling Non-asbestos Hi-Temp Exhaust Repair Bandage is wet and ready to use when removed from the air sealed package. When hardened by exhaust heat, it turns into a hard, long lasting repair. DIRECTIONS FOR USE: 1. Clean off loose rust and dirt from the damaged area of muffler or tailpipe with sandpaper or a steel wire brush. 2. Remove bandage from the sealed foil packet and wrap the wet bandage around the damaged area with the specially impregnated material against the muffler or tailpipe, overlapping 10-15mm. 3. Support the wrapped bandage temporarily with the enclosed wire until it is heat cured. 4. Idle the motor in the open air for 20-30 minutes. The exhaust heat will harden it to a hard, protective coating.
$10.00
LOCTITE 660 is a high strength retaining compound with good gap filling properties, ideal for repairing worn-out seats, keys, splines, bearings or tapers without remachining. LOCTITE® 660 is designed for the bonding of cylindrical fitting parts, particularly where bond gaps occurs without the need for remachining. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. LOCTITE 660 exhibits excellent gap cure characteristics and is also suitable for retaining shims. Ideal for repairing worn parts without remachining Enables re-use of worn bearing seats, keys, splines or tapers Suitable for retaining shims P1 NSF Reg. No.: 123704 Technical Information Agency Approvals / Specifications NSF P1 Color Silver Diametrical Clearance (Maximum) Unit mm Fixture Time 15 min. Fixture Time Temperature 15 °C Gap Fill 0.5 mm Key Characteristics Thixotropic Substrates Metal: Steel
$10.59
Retaining Compound - medium strength. If disassembly is required. Ideal for parts that need subsequent dismantling. LOCTITE® 641 is designed for the bonding of cylindrical fitting parts, particularly where disassembly is required for servicing operations. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings Technical Information Colour Yellow Diametrical Clearance (Maximum) 0.1 mm Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.1 mm Shear Strength Unit, Steel psi Shear Strength, Steel 1700 Specific Gravity 1.07 g/l Specific Gravity Temperature 25 °C Substrates Metal: Steel Temperature -65 - 300 °F Viscosity 525 - 1950 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$22.40
High strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. LOCTITE® 609 is a green, high strength methacrylate ester acrylic retaining compound designed for the bonding of cylindrical fitting parts. The product cures in the absence of air between close-fitting metal surfaces. Typical applications include rotor to shafts in fractional and subfractional horsepower motors. Locks bushings and sleeves in housings on shafts. Augments press fits. Low viscosity Prevents loosening and leakage from shock and vibration Augments press fits Tested to the lot requirements of Military Specification Mil-R-46082B (this is a regional approval) Technical Information Agency Approvals / Specifications ASTM D5363, CFIA Listed, MIL-R-46082B for existing designs Application Method Pressure Applications For Close Fitting Parts, Retaining Colour Green Cure Type Anaerobic Cure Diametrical Clearance (Maximum) Unit in. Fixture Time 10 min. Fixture Time Temperature 10 °C Full Cure Temperature 22 °C Full Cure Time 24 hr. Gap Fill 0.006 in. Key Characteristics Fluorescent, Strength: High Strength, Viscosity: Low Viscosity Number of Components 1 Part Physical Form Liquid Shear Strength Unit, Steel psi Shear Strength, Steel 2300 Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal Technology Acrylic Temperature -65 - 300 °F Viscosity 125 mPa.s (cP) Brookfield Viscosity (#7sp/20/rpm) 125 mPa.s (cP) Brookfield Viscosity Temperature 25 °C
$12.12
Thread Sealant - medium strength. For fine threads in hydraulic, pneumatic and general fittings. Fast curing. LOCTITE® 542 is designed for the locking and sealing of metal pipes and fittings as well as other cylindrical metal assemblies. The product cures when confined in the absence of air between close-fitting metal surfaces and prevents loosening and leakage due to shock and vibration. The thixotropic nature of LOCTITE 542 reduces the migration of liquid product after application to the part. Ideal for fine threads as used in hydraulic, pneumatic & general fittings Suitable for metal threads only Instant low-pressure seal Resistant to fuel, oil, coolants and hydraulic fluids Locks connection against vibration loosening PRODUCT DESCRIPTION LOCTITE® 542 provides the following product characteristics: Technology Acrylic Chemical Type Dimethacrylate ester Appearance (uncured) Brown liquidLMS Components One component - requires no mixing Viscosity Low Cure Anaerobic Secondary Cure Activator Application Thread sealing Strength Medium Directions for use: For Assembly 1. For best results, clean all surfaces (external and internal) with a LOCTITE® cleaning solvent and allow to dry. 2. If the material is an inactive metal or the cure speed is too slow, spray all threads with and allow to dry. 3. Apply a 360° bead of product to the leading threads of the male fitting, leaving the first thread free. Force the material into the threads to thoroughly fill the voids. For bigger threads and voids, adjust product amount accordingly and apply a 360° bead of product on the female threads also. 4. Using compliant practices, assemble and wrench tighten fittings in accordance with manufacturers recommendations. 5. Properly tightened fittings will seal instantly to moderate pressures. For maximum pressure resistance and solvent resistance allow the product to cure a minimum of 24 hours. For Disassembly 1. Remove with standard hand tools. 2. Where hand tools do not work because of excessive engagement length or large diameters (over 1"), apply localized heat to approximately 250 °C. Disassemble while hot. For Cleanup 1. Cured product can be removed with a combination of soaking in a Loctite solvent and mechanical abrasion such as a wire brush.
$12.26
LOCTITE 518 is a medium-strength, general purpose gasketing product with excellent contamination tolerance. Ideal for use on casted iron, steel and aluminum flanges. LOCTITE® 518 cures when confined in the absence of air between close-fitting metal surfaces. It is an anaerobic gasketing material designed for use on rigid iron, aluminum, and steel flanged mating surfaces. LOCTITE 518 fills gaps up to 0.25mm and forms a flexible, chemical-resistant seal that will not tear or decay. Parts disassemble easily, even after extended service. Typical applications include sealing close-fitting joints between rigid metal faces and flanges. It is also used as a formed-in-place gasket on rigid flanged connections, e.g. transmissions and motor housings. Semi-flexible, medium-strength anaerobic flange gasket Easy to automate Reduces process costs – eliminates manual assembly of conventional gaskets NSF P1 Reg. No. 123758 For active and inactive rigid metal flanges Cures through minor surface contamination Adapts to flange surface irregularities and gaps up to 0.25 mm Gel-type consistency Seals instantly against low pressure Reduces inventory costs – no need for large inventory of cut gaskets Resists high pressure when fully cured No compression set or misaligned gaskets Technical Information Applications Rigid Assembly Gasketing Colour Red Cure Schedule Temperature (Step 1) 200 Cure Schedule Temperature Unit (Step 1) °C Fixture Time 25 min. Fixture Time Temperature 25 °C Full Cure Temperature 77 °F Gap Fill 0.3 mm Shelf Life Temperature -40 °C Specific Gravity 1.1 g/l Specific Gravity Temperature 25 °C Substrates Metal: Aluminum Temperature -65 - 300 °F Tensile Shear Strength 7.5 N/mm² Viscosity 500000 - 1000000 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$9.95
LOCTITE 454 is a general-purpose, non-drip gel, instant adhesive that is ideal for vertical surfaces and overhead applications. LOCTITE® 454 is an instant adhesive designed for the assembly of difficult-to-bond materials that require uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. The gel consistency enables overhead and vertical applications. LOCTITE 454 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repair jobs. Universal instant adhesive gel Will not drip or run Non-wicking, especially suited to porous materials Perfect for all quick repairs Ideal for overhead application and vertical faces Bonds similar or dissimilar substrate combinations of wood, metals, ceramics, most plastics Technical Information Colour Clear: Ultra Clear Fixture Time 5 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose Physical Form Gel Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F
$24.59
Black, toughened ethyl-based instant adhesive. Well suited to plastics, rubbers, metals as well as porous/acidic surfaces. LOCTITE® 438 is a black, toughened ethyl-based instant adhesive. It has a fixture time of 10 - 20 secs., high impact resistance and is flexible. It is suitable for bonding plastics, rubber, metals, porous and absorbent substrates and acidic surfaces. Good resistance in humid environments. Cures very quickly when confined between two surfaces Ideal for bonding small to medium-size parts Excellent adhesion to most substrates Suitable for rubbers and plastics Well suited to metals, porous and/or acidic surfaces Fixture time of 10 - 20 secs. Solvent-free Toughened, black
$35.00
LOCTITE 406 is a low viscosity, fast curing instant adhesive that is ideal for bonding plastics and elastomeric materials where very fast fixturing is required. LOCTITE® 406 is an instant adhesive designed especially for the fast bonding of plastics and rubbers. This product offers exceptionally low viscosity. When combined with LOCTITE primers for cyanoacrylates, it can also be used on difficult-to-bond plastics. Rapid bonding of plastic & rubber, including EPDM LOCTITE 770 or LOCTITE 7239 primer improves adhesion of difficult-to-bond substrates Technology Cyanoacrylate Chemical Type Ethyl cyanoacrylate Appearance (uncured) Transparent, colorless to straw colored liquid LMS Components One part - requires no mixing Viscosity Low Cure Humidity Application Bonding Key Substrates Plastics and Rubbers TYPICAL CURING PERFORMANCE Under normal conditions, atmospheric moisture initiates the curing process. Although full functional strength is developed in a relatively short time, curing continues for at least 24 hours before full chemical/solvent resistance is developed. Technical Information Colour Clear: Ultra Clear Fixture Time 2.0 - 10.0 sec. Gap Fill 0.05 mm Key Characteristics Viscosity: Low Viscosity Substrates Plastic, Rubber
$18.32
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$5.87
LOCTITE 401 is a general purpose, fast curing, instant adhesive that is ideal for use on porous substrates. LOCTITE® 401 is a fast curing instant adhesive designed for the assembly of difficult-to-bond materials requiring uniform stress distribution and high tensile and/or shear strength. The product provides for the rapid bonding of a wide range of materials, including metals, plastics and elastomers. LOCTITE 401 is also suited to bonding porous materials such as wood, paper, leather and fabric. Perfect for all quick repairs and all types of small emergency repairs. Universal instant adhesive Very high strength on close-fitting parts Perfect for all quick repairs and all types of small emergency repairs. Bonds a wide range of similar or dissimilar substrates (metals, rubber, wood, cardboard, ceramics as well as most plastics) Technical Information Colour Clear: Ultra Clear Fixture Time 3 - 10 sec. Full Cure Temperature 77 °F Gap Fill 0.15 mm Key Characteristics General Purpose, Viscosity: Low Viscosity Shear Strength Unit, Grit Blasted Steel psi Shear Strength, Grit Blasted Steel 3200 Specific Gravity 1.05 g/l Specific Gravity Temperature 25 °C Temperature -65 - 250 °F Viscosity 110 mPa.s (cP) Brookfield Viscosity Temperature 77 °F
$18.32
Bonds metals, ceramics, concrete, fibreglass, marble and wood. Syringe dispenser accurately measures equal amounts of resin and hardener to prevent wastage. Fast curing, cure commences in five minutes and reaches full cure in one hour. When cured, the bond is transparent and virtually colourless. Loctite 5 Minute Epoxy Adhesive's premium formulation is solvent-free and 100% solids providing a non-shrink, environmentally friendly bond. High viscosity provides a good gap-filling ability. DIRECTIONS FOR USE: 1. Surfaces must be clean and dry. If possible, roughen surface with sandpaper to improve keying and bonding. 2. Cut tips of twin nozzle with a sharp knife and remove nozzle cap from syringe plunger. 3. Push the twin plunger to squeeze out equal amounts of resin and hardener in the amounts required. 4. Mix the resin and hardener for one or two minutes until the colour is completely uniform. 5. Apply immediately to both surfaces and press together. Pressure clamping is not necessary, but allow the adhesive to set for at least 5 minutes before moving. Remove any excess adhesive immediately. 6. Important. After dispensing product be certain to insert plug supplied in the nozzle of the syringe to prevent waste. Preferably store in an upright position as packaged. Structural Bonding - Fast Cure. Sets in 5 minutes. Sets in 5 minutes. Good chemical resistance. Fixture time: 4-6 min Temperature Resistance: Up to 180°F (82°C)
$15.11
You have seen 432 out of 498 products
Professional-level performance for strength, durability and productivity on site. Expect defined movement capability, temperature/chemical ratings and precise application methods. Use filters to refine by chemistry and pot life. Always review the product page and TDS/SDS.
