Crommelin High UV Resistant Roof and Wall Waterproofing is a premium, liquid-applied elastomeric membrane for exposed, above-ground surfaces, supplied here in a 10L grey pack. It is made for places that cop full sun all year, such as rooftops, walls, parapets and balconies, and it forms a seamless, flexible waterproof coating that can also handle foot traffic.About the formulaThis is a high-performance elastomeric membrane that stays flexible once cured, so it can move with the surface beneath it. Because it goes on as a liquid, it forms one continuous film without laps or joins, which helps give leak-free performance. The manufacturer also lists it as an effective anti-carbonation coating for concrete. It resists dirt pick-up and algal growth, and it can be over-coated with acrylic paints if you want a particular finish. The manufacturer lists compliance with AS 4654.1 (waterproofing membrane systems for exterior use, above ground level, Part 1).Where to use itIndoors: not intended for interior use. It is made for exposed exterior situations.Outdoors: roofs and rooftops, exterior walls and facades, parapets, balconies, terraces, vertical surfaces and timber cladding or screening, including on trafficable areas that see regular foot traffic.Suitable surfaces listed by the manufacturer include concrete, concrete blocks, brickwork, masonry, renders, fibre cement sheeting, compressed cement sheets, timber (hardwood and pine) and suitably prepared metal such as steel and aluminium. Always test a small area first, especially on previously coated or challenging surfaces.How to use itPrepare the surface so it is clean, sound and free of dust, grease, loose paint and other contaminants. Metal needs suitable preparation before coating. Apply a test patch to confirm adhesion and appearance, then follow the manufacturer application instructions and technical data sheet for coat numbers, coverage rates and recoat times. If you plan to paint over the membrane, use an acrylic paint.Important notesThis product is designed for above-ground, UV-exposed use. Check the manufacturer technical data sheet before using it where water will pond or sit permanently, or where it will be covered by tiles. Cure and recoat times depend on temperature, humidity and film thickness, so follow the data sheet rather than guessing. Keep the membrane protected from damage until it has fully cured.Specifications Brand Crommelin Product High UV Resistant Roof and Wall Waterproofing Size 10L Colour Grey Type Elastomeric, liquid-applied waterproofing membrane Standard AS 4654.1 (exterior, above ground level) Over-coating Suitable for acrylic paints Traffic Suitable for pedestrian traffic Use Exterior, above ground, UV exposed SafetyStandard good practice still applies: wear gloves and eye protection, avoid contact with eyes and skin, and use in a well-ventilated area. Keep out of reach of children, store the container sealed in a cool, dry place, and do not let product enter drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$264.15
Bastion Waterproofing Reinforcing Fabric is a lightweight woven polyester fabric that is embedded between coats of liquid waterproofing membrane, supplied here as a 100mm wide x 50m roll. It adds protective reinforcement to the cured membrane and helps the finished coating stand up to movement, puncturing and general wear, particularly in the spots most likely to fail.About the fabricA white woven polyester fabric that wets into liquid membrane coats easily, so it beds down neatly without fuss. It resists rupture and tearing, has good rot resistance, and helps lift the puncture resistance and tensile strength of the membrane finish. It is also compatible with cement-based finishes such as tile adhesives, renders and textures.Where to use itIndoors: reinforcing critical areas of movement in a waterproofing system, including joints, internal corners, and around pipes and other penetrations, as well as over cracks in the substrate.Outdoors: use as part of a membrane system where the membrane itself is rated for the exposure. Check the membrane manufacturer's instructions for the specific application.Designed for use with liquid waterproofing membranes and cement-based finishes. The 100mm width suits narrow strips along junctions, corners, joints and cracks. Always follow the instructions for the membrane system you are using.How to use itPrepare the substrate and apply any primer and the first membrane coat as directed by the membrane manufacturer. While the coat is still wet, lay the fabric into it, smooth it flat and wet it in fully so it is saturated and free of wrinkles and air bubbles. Overlap cut ends so the reinforcement is continuous, then apply the following membrane coat over the top, as per the membrane's instructions. Cut the fabric to length with scissors or a sharp knife.Important notesThis is a reinforcing fabric only and does not waterproof on its own. It must be used with a suitable liquid waterproofing membrane. Coating thickness, number of coats, drying times and compliance with wet area requirements (such as AS 3740) depend on the membrane system and installation method, so check the membrane's technical data and local requirements. Store the roll clean and dry.Specifications Brand Bastion Product Waterproofing Reinforcing Fabric Size 100mm wide x 50m roll Colour White Material Woven polyester fabric Application Embedded by hand between coats of liquid membrane Compatible with Liquid membranes and cement-based finishes (tile adhesives, renders, textures) SafetyWear gloves and eye protection when cutting and applying, and follow the PPE advice for the membrane system. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$21.11
Crommelin Sprayable Exterior Grade Waterproofing is a rubberised, shake-and-spray waterproofing coating in a 400ml aerosol, made for outdoor areas that cop regular water and UV exposure. It is designed to seep into and seal leaks, cracks and small gaps, leaving a flexible, watertight film that suits quick repairs on roofs, gutters and similar exterior surfaces. This pack is the grey finish.About the formulaA rubberised coating delivered from a pressurised can, so there is no brush, roller or mixing involved. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), permanently flexible and fast drying. It also helps protect the coated surface from corrosion and stops moisture getting through. Once cured it can be overcoated with most water-based (acrylic) paints.Where to use itIndoors: not intended for interior use. This is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, hoses, air conditioner drip pans and ductwork.Suitable surfaces listed by the manufacturer include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particle board, PVC piping and fibreglass. The product has not been tested for use in potable water systems.How to use itSurfaces must be clean, sound and dry, and free of dust, grease, release agents, loose particles and other contaminants. Shake the can vigorously for one minute, and do a test spray on cardboard to get a feel for the spray pattern. Hold the can roughly 8 to 18cm from the surface and apply a thin first coat, which acts as a primer, then let it dry. Follow with a heavier coat, moving the nozzle a little closer to build a thicker film. For longer-lasting protection apply three to four coats, and for wider cracks and gaps keep adding coats until the cavity is filled. Apply to the positive side only (the side where water enters the substrate). Recoat once touch dry, which is about 20 to 30 minutes depending on thickness, weather and site conditions, and allow good airflow to help it cure.Important notesApply in temperatures of about 10 to 30 degrees C and avoid applying when humidity is high (the recommended maximum is 85% during application and cure). Avoid spraying in high wind or dusty conditions. Cold temperatures and poor airflow will lengthen cure times. It can be painted over after 24 hours. Full cure takes 48 hours, and the coating should not be exposed to water until then. Coverage depends on the shape and condition of the surface. Always do a small test area first.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 400ml aerosol can Colour Grey Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Recoat time About 20 to 30 minutes (touch dry) Paint over After 24 hours Full cure 48 hours Application temperature 10 to 30 degrees C Overcoating Most water-based (acrylic) paints Use Exterior SafetyKeep away from heat, sparks, flames and hot surfaces, do not spray onto a flame or ignition source, and do not pierce or burn the can, even when empty. Use in a well-ventilated area, avoid contact with skin, eyes and clothing, and wash hands before eating, drinking or smoking. Store out of direct sunlight and keep below 50 degrees C. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Crommelin One Coat Rapid is a heavy-duty, liquid-applied waterproofing membrane that goes down before tiling, supplied here in a 1L pail for showers, laundries and other small wet-area jobs. It is a polyurethane-modified grey membrane that cures into a seamless, flexible layer under tile, so there are no laps or joins in the finished surface.About the formulaThe membrane is polyurethane modified for high flexibility and reinforced for strength and durability. Crommelin states it stretches by more than 300% and stays flexible over time, which helps it cope with minor substrate movement. It dries to a keyed, slightly textured surface that gives cement-based tile adhesive something to grip. It is made to be used with cement-based tile adhesives that comply with AS 2358, and it is designed to meet AS 4858 and AS 3740. It is water based, so tools clean up with water.Where to use itIndoors: showers, bathrooms, laundries and kitchens, on both walls and floors, before tiling.Outdoors: balconies, patios and podiums under tile, where the membrane is covered by the tile finish.Suitable substrates include concrete, cement render and screeds, plasterboard and wet-area plasterboard, suitably prepared compressed fibre cement sheet, timber, plywood, wet-area particleboard and steel.How to use itSurfaces need to be sound, clean and dry, with loose or crumbling material removed first. New concrete should have cured for at least 28 days before coating. Where the manufacturer's data sheet calls for a surface primer, use a 1:1 dilution of the membrane with water and let it dry. On walls, one coat is enough, and Crommelin quotes coverage of up to 2m² per litre. Floors need more material per square metre, and complex or irregular surfaces may need extra coats, so check the technical data sheet for your job. Allow good airflow while it cures. Once the membrane has cured, a flood test is described in the manufacturer's data sheet: water about 25mm deep for 2 hours, removed straight afterwards. Clean tools with water before the membrane dries. Uncured material can be removed with warm water and detergent.Important notesThis membrane is not designed to go directly onto white-set plaster. Prime that surface first with a coat of Crommelin Next Day New Concrete Sealer and let it dry. Full cure takes about 7 days. Re-coat and cure times get longer in cold, humid or still conditions. Tile over the membrane so it is not left exposed. Waterproofing wet areas is regulated work in many parts of Australia, so check local requirements and follow the manufacturer's full instructions.Specifications Brand Crommelin Product One Coat Rapid Under-tile Waterproofing Membrane Pack 1L pail Colour Grey Base Polyurethane-modified, liquid applied, water clean up Elongation Over 300% Coverage Up to 2m² per litre (see data sheet for floors and irregular surfaces) Full cure About 7 days Standards Designed to comply with AS 4858 and AS 3740 Use Interior and exterior under-tile applications SafetyUse it with good general ventilation, avoid prolonged skin and eye contact, and wash your hands after use. Store the pail sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$36.48
Crommelin Exterior Grade Brushable Waterproofing Membrane is a tough, flexible synthetic rubber coating for external areas that stay wet, supplied here in a 15L pail for larger jobs. It is designed for permanent water contact, for non-exposed areas with pedestrian traffic, and for use beneath screeds and toppings. It is built to move with the structure rather than crack as the building shifts.About the formulaA ready-to-use, water-based, synthetic rubber membrane (styrene butadiene rubber) in grey. It stays permanently flexible, bridges existing cracks up to 1.5mm and bonds to a wide range of building substrates. It is low VOC and dries quickly. Once cured it can be overcoated with screeds, renders and water-based coatings, so it suits layered waterproofing systems.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin offers separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits other areas of permanent water contact and non-exposed areas under screeds and toppings.Suitable substrates listed by the manufacturer include concrete and brick, cement render, plywood sheeting, cement sheeting, lightweight aggregate block, trafficable screeds, aluminium and steel (suitably primed).How to use itSurfaces must be sound, clean and completely dry, with no dust, grease, curing compounds, release agents, loose particles or efflorescence. Test moisture content before coating, ideally with an electronic moisture meter. Concrete should be cured for at least 28 days, and screeds and renders for at least 7 days. Remove high points and fill blow-holes and honeycombing with a suitable repair mortar. If the substrate is damp, prime it with Crommelin Dampstop. Treat any rust and remove loose rust material before coating metal. Stir the membrane well, then apply with a Crommelin applicator brush or roller at a surface and air temperature between 10 and 35 degrees Celsius. Recoat once touch dry, which is about 2 hours. Apply the second coat at right angles to the first. Reinforce corners, gutter damage and pin holes with Crommelin reinforcing fabric or bandage. Fit a suitable protection board over the cured membrane before any backfilling.Important notesDo not apply in extreme temperature or humidity. Full cure is about 7 days at 25 degrees Celsius, and coverage varies with substrate porosity. This product is intended for non-exposed pedestrian traffic, so protect the membrane from mechanical damage. Crack bridging applies to existing cracks up to 1.5mm only. Check the current manufacturer data sheet for your specific application and overcoating requirements.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofing Membrane Pack 15L pail Colour Grey Base Water-based synthetic rubber (styrene butadiene rubber) Application Brush or roller Coverage About 1.5m² per litre, roughly 11m² of finished coating per 15L Recoat time About 2 hours Full cure About 7 days at 25°C Crack bridging Existing cracks to 1.5mm Application temperature 10°C to 35°C Use Exterior, permanent water contact, non-exposed trafficable areas, under screeds and toppings SafetyAvoid contact with skin and eyes, wear suitable gloves and eye protection, and ensure good ventilation when applying. Store in a cool, dry place with the lid sealed. Wash tools in water before the membrane cures. Refer to the Safety Data Sheet (SDS) for full details.
$336.74
Crommelin Shower Sealer & Waterproofer is a clear, water-based silicate treatment designed to stop leaking showers by waterproofing the grout from within, with no need to rip out tiles. It soaks deep into cementitious grout and reacts inside it to block the passage of moisture, making it a practical fix for old, porous grout in showers, bathrooms and balconies. This listing is for a single 500ml bottle.About the formulaA waterborne silicate treatment that penetrates grout to a depth of up to 20mm. Once in the grout it undergoes a chemical reaction that Crommelin says permanently blocks moisture, and it dries completely clear so your tiles and grout lines look the same afterwards. It is a ready-to-use, single coat treatment, so there is no mixing, and equipment cleans up with water.Where to use itIndoors: shower recesses, bathrooms, kitchens and laundries with cementitious grout that has started to leak or let moisture through.Outdoors: balconies and other external areas with cementitious grout or similar cementitious construction materials.Suitable substrates are cementitious grout and other cementitious construction materials. It is not suitable for epoxy grout.How to use itPreparation: make sure the area is cementitious and free of dirt, mould, mildew and other contaminants. Wash with a strong bleach solution and rinse well. Replace any loose or drummy tiles and repair damaged or cracked grout with cementitious grout. Seal metal inserts with silicone, and make sure wall-to-wall and wall-to-floor joints are sealed with silicone rather than grout. The surface must be dry, so leave the area to dry for at least 12 hours before applying.Application: shake the bottle well, then apply liberally to the grout joints only, using a thin brush or a Crommelin Sealer Applicator Wheel. Wipe any excess off the tile surface with a damp cloth before it dries. Leave to dry for 30 to 40 minutes, then water the area thoroughly and scrub off any remaining excess. The area can be used straight away.Conditions: apply only when surface and air temperatures are within 10°C to 35°C, and avoid application when humidity is high or likely to be during the initial cure (maximum recommended humidity is 85%).Clean up: wash brushes and tools with water before the product dries.Important notesFull cure takes 7 days. Not suitable for epoxy grout. The grout must be clean and dry, and contaminants such as mould or old sealers can stop the treatment from penetrating properly. Crommelin's data sheet gives coverage of roughly 200 to 300 lineal metres of 5mm grout from the 500ml bottle, so actual coverage depends on grout width, depth and porosity. For full preparation and application detail, follow the Crommelin instructions and technical data sheet.Specifications Brand Crommelin Product Shower Sealer & Waterproofer Pack 1 x 500ml bottle Manufacturer code 6001-500 Colour Clear (dries clear) Base Waterborne silicate treatment Application Thin brush or Crommelin Sealer Applicator Wheel, grout joints only Penetration Up to 20mm into grout Dry time before watering in 30 to 40 minutes Full cure 7 days Application temperature 10°C to 35°C Coverage Approx. 200 to 300 lineal metres of 5mm grout (per manufacturer TDS) Clean up Water, before the product dries Use Interior and exterior SafetyAs a general precaution, avoid contact with eyes and skin, keep out of reach of children, and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$61.24
Crommelin Blackseal Heavy Duty is a water-based, rubber-modified bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 1L size that suits planter boxes, pots, timber posts and small retaining wall jobs. It is made for surfaces that stay damp or wet and will not be painted, tiled or covered with a finishing coat.About the formulaCrommelin describes Blackseal as a commercial grade bitumen emulsion modified with a synthetic rubber co-polymer. The rubber modification keeps the cured film flexible, so it stays watertight under permanently wet conditions and is suitable for permanent immersion. It helps prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. It grips a wide range of substrates, is fast drying, and the maker lists it as non-toxic and non-flammable. It can be thinned with up to 50% water to make a bitumen paint.Where to use itIndoors: not intended for interior finishing work or any area that needs a paintable or tileable surface.Outdoors: below-ground and non-exposed exterior surfaces such as garden retaining walls, planter boxes, plant pots, timber posts, water tanks and other non-critical moisture barrier jobs.Suitable materials include concrete, masonry, cement sheeting, timber and metal (check the label for the full substrate list and do a small test area first).How to use itStart with a clean, sound surface free of dust, grease, loose material and anything that could stop the membrane bonding. Stir the product well and apply it evenly with a brush or roller, then allow it to dry before any further coats. Check the label and Crommelin's full instructions for coverage, coat numbers and drying times before you start, and protect the cured membrane from damage if you will be backfilling against it. Clean tools before the product dries (as a water-based product, warm water is the usual method, but confirm on the pack).Important notesNot suitable where it will be exposed to UV or sunlight. It cannot be painted, tiled over, rendered or over-coated, and it is not for trafficable surfaces. If you need a UV-stable option, look at a different Crommelin product. Coverage and cure times depend on the surface and conditions, so treat the listed coverage as a guide and test a small area first.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Size 1L Colour Black Base Water-based bitumen emulsion, modified with a synthetic rubber co-polymer Application Brush or roller Coverage Approx. 0.75 m² per 1L (retailer listed, guide only) Dilution Up to 50% water to make a bitumen paint Use Below-ground and non-UV-exposed exterior areas Not suitable for UV exposure, painting, tiling, over-coating, trafficable surfaces SafetyThe product itself is not combustible, but once the water has evaporated the organic components can burn or break down in a fire. Avoid contact with eyes and skin, keep out of reach of children, and wash off spills and splashes promptly. Refer to the Safety Data Sheet (SDS) for full details.
$20.75
Crommelin Blackseal Heavy Duty is a black, water-based bitumen waterproofing membrane for below-ground and other non-UV-exposed surfaces, supplied here in a 15L pail for larger jobs. It is a bitumen emulsion modified with a synthetic rubber co-polymer. It dries to a strong, flexible film that stays watertight in permanently wet conditions, which makes it a practical, economical choice where the finished membrane will stay out of sight and out of the sun.About the formulaA water-based bitumen emulsion with a synthetic rubber co-polymer for added flexibility and strength. It grips well to a wide range of building surfaces and is designed to help prevent the damage that moisture transfer causes, including efflorescence, mould growth, staining and paint peeling. The manufacturer describes it as non-toxic, non-flammable, fast drying and suitable for permanent immersion. It can be thinned with up to 50% water if you want a bitumen paint instead of a full-strength membrane.Where to use itIndoors: not intended for interior wet areas such as showers or bathrooms, because it cannot be tiled over or finished with a top coat.Outdoors: below-ground and non-exposed outdoor surfaces, including garden retaining walls, planter boxes, plant pots, timber posts and water tanks. It suits non-critical waterproofing jobs, not areas next to habitable spaces.Suitable surfaces include concrete, concrete blocks, brickwork and other masonry, renders, cementitious substrates, compressed cement and fibre cement sheeting, natural stone, plywood sheeting and timber. It also works on aluminium and steel that have been suitably prepared.How to use itStart with a clean, sound surface free of dust, grease, loose material and flaking coatings. Stir the pail well, then apply with a brush or roller. Two coats are recommended, and the 15L pail covers about 11.25 square metres at that rate. Let each coat dry before applying the next. Mix with water only if you want to thin it for use as a bitumen paint, and do not go past 50% dilution. Wash tools with water straight after use, before the product dries. Check the current Crommelin product information sheet for recoat times and full preparation advice before you start.Important notesDo not paint, tile over or over-coat this membrane, and do not use it on trafficable surfaces. It is not suitable where UV stability is required, so keep it covered or buried. For shower areas or UV-exposed roofs and walls, choose a purpose-made Crommelin membrane instead. Because it is for non-critical applications only, it is not a substitute for a compliant waterproofing system in habitable or wet areas. Cure times vary with temperature, humidity and airflow, so allow enough time before backfilling or exposing the membrane to heavy moisture.Specifications Brand Crommelin Product Blackseal Heavy Duty Bitumen Waterproofing Membrane Pack 15L pail Colour Black Base Water-based bitumen emulsion modified with synthetic rubber co-polymer Application Brush or roller Number of coats 2 Coverage About 11.25 square metres per 15L (two coats) Dilution Up to 50% water to make a bitumen paint Clean up Water, while wet Use Below ground and non-UV-exposed areas only SafetyUse it with good general ventilation. Normal site protection such as safety glasses and overalls is sensible, along with good hygiene. Store the pail sealed, away from extreme temperatures and freezing, and keep it away from strong oxidising agents, strong acids and strong bases. Do not let large spills reach drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$125.78
Crommelin AquaBlock Waterproof Primer Undercoat is a water-based primer, sealer and stain-blocking undercoat made for damp-prone areas of the home, supplied here in a 1L tin that suits bathroom, laundry and small repaint jobs. It builds a water-resistant, paintable base over bare and previously painted surfaces, so water-based topcoats can go on over an even, sealed surface.About the formulaAquaBlock is a high-cover, low-odour wall primer with a flat finish. Crommelin positions it as a sealer, primer, undercoat and stain blocker in one product. It grips both porous and non-porous surfaces, seals off stains and gives topcoats a uniform surface to bond to. The manufacturer also describes it as a mould-resistant undercoat, which makes it a sensible choice for bathrooms, kitchens and laundries. It is designed to be overcoated with water-based paints and cleans up with water.Where to use itIndoors: walls and ceilings in bathrooms, kitchens, laundries and hallways, especially where steam, condensation or past moisture damage has caused staining or peeling.Outdoors: eaves and exterior walls and other masonry or timber surfaces that will be topcoated with a water-based paint.Suitable surfaces include plasterboard, brick, concrete and concrete blocks, cement sheeting, render, masonry, timber, plywood, particleboard and suitably prepared steel.How to use itMake sure the surface is clean, dry, sound and free of dust, grease, loose paint and mould before you start. Stir the product well, then apply it with a brush or roller. Check the label for the recommended number of coats and the spread rate for your surface. Apply only when the temperature is at least 5°C. The retailer lists a recoat time of about 120 minutes. Clean brushes, rollers and tools with water straight after use, before the product dries.Important notesThis product is not tintable and is supplied in white only. Crommelin advises it is not suitable over white set plaster and should not be used as a base before tiling. It is a primer and undercoat, not a decorative finish, so topcoat it with a water-based paint. Surface and weather conditions affect drying and performance, so test a small area first on unusual or heavily stained substrates. Check the label for full application details.Specifications Brand Crommelin Product AquaBlock Waterproof Primer Undercoat Size 1L tin Colour White (not tintable) Finish Flat Base Water-based Application Brush or roller Coverage 12 to 14 m² per litre (retailer figure; check the label) Recoat time About 120 minutes Minimum application temperature 5°C Clean up Water Topcoat Water-based paints Use Interior and exterior SafetyEven so, avoid contact with skin and eyes, wear suitable protective clothing and gloves, and use it in a well-ventilated area. Keep the lid on the tin when not in use, store it in a cool, dry place and protect it from freezing. Keep it out of reach of children. Do not tip leftover product or wash water into drains or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$37.54
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane for waterproofing wet areas before tiling, supplied here in a 15L pail for larger bathroom, laundry and balcony jobs. It cures to a continuous, flexible rubber-like layer with a textured surface, so cement-based tile adhesive can bond directly over the top.About the formulaA heavy duty, modified rubber (styrene butadiene rubber) liquid membrane that is applied seamlessly, with no joins or laps, for leak-free performance. It stays permanently flexible with high elongation, so it can cope with normal movement in the substrate. It dries to a keyed finish suited to all cement-based tile adhesives that conform to AS 2358, and it complies with AS 3740 (Waterproofing of wet areas). It is a water-based product, so tools clean up with water.Where to use itIndoors: under tiles in showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors.Outdoors: under-tile waterproofing on balconies. The membrane can be applied either below or above a screed.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area gyprock, compressed fibre cement sheeting, timber, plywood sheeting and wet area particleboard, and suitably prepared steel.How to use itPrepare the surface first. Remove high points and protrusions, fill any blow-holes or honeycombing with a suitable repair mortar, and bring the surface back to an even profile. New concrete should have cured for at least 28 days and screeds or renders for at least 7 days. The surface must be clean, sound and completely dry. Free it from dust, grease, curing compounds, release agents and loose particles. Check moisture with a meter. If the substrate is not dry enough, prime it with Crommelin Dampstop.The membrane is ready to use, so stir it well and apply with a brush or roller. Apply at least two coats and allow the first to dry before recoating. Complex or very irregular surfaces may need extra coats. Apply only when surface and air temperatures are between 10 and 35 degrees C and humidity is below 85%.Tile over after the membrane has dried and cured for the recommended time. A flood test can be done after 48 hours by ponding water to a depth of 25mm for 2 hours, then removing the water straight away. Wash tools with water before the product dries. Uncured material can be removed with warm water and detergent.Important notesNot suitable for use over white-set plaster. Do not apply over damp substrates, and do not apply in extreme heat, cold or humidity. Allow good airflow so the membrane can cure properly. Full cure takes about 7 days. Recoat and tile-over times vary with temperature and humidity, so check the current Crommelin data sheet for your conditions. Crommelin lists companion products for detailing, including reinforcing fabric with bond breaker, Dampstop primer, polyurethane sealant and Silicone WP Plus. Always apply a trial patch if you are unsure about a substrate.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 15L pail Colour Green Base Water-based, modified rubber (SBR) liquid applied membrane Application Brush or roller, ready to use after stirring Coverage About 2m2 per litre per coat, minimum 2 coats (about 15m2 of finished membrane from 15L) Application temperature 10 to 35 degrees C, maximum humidity 85% Tile over After a minimum of 48 hours Full cure 7 days Standards Complies with AS 3740; suitable for use with cement-based tile adhesives conforming to AS 2358 Use Under-tile wet area waterproofing SafetyEven so, ensure good ventilation, avoid breathing vapours or spray, avoid skin and eye contact, and wear gloves and eye protection. Remove splashes from skin promptly. Keep the container sealed when not in use, store it cool and dry, and protect it from freezing and extreme temperatures. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$273.47
![Crommelin Sprayable Exterior Grade Waterproofing 400ml [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-sprayable-exterior-grade-waterproofing-400ml-white-2.jpg?v=1792410554&width=645)
Crommelin Sprayable Exterior Grade Waterproofing is a ready-to-spray rubberised coating for sealing leaks and cracks on outdoor surfaces, supplied here as a 400ml aerosol can in white. It is made for spots that cop regular rain and sun, and it dries to a flexible, watertight layer that can be painted over with most acrylic paints.About the formulaA rubberised waterproofing coating in a pressurised can, so there is no brush, roller or mixing involved. The spray works its way into small holes and cracks to stop water getting through, helps block moisture penetration, and gives metal surfaces a barrier against corrosion. The manufacturer describes it as UV stable, weather resistant (it does not fade or yellow), fast drying and permanently flexible. The white finish suits light-coloured roofing and masonry.Where to use itIndoors: not intended for interior use, as this is an exterior grade product.Outdoors: roofs and gutters, chimneys, skylights, block and brickwork, and hoses, air conditioner drip pans and ductwork.Suitable materials include metal (steel and aluminium), concrete and masonry, roofing materials, timber and particleboard, PVC piping and fibreglass.How to use itMake sure the surface is clean, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and any other contaminants. Crommelin recommends its Water Rinsable Degreaser for removing grease and oils. Shake the can well, then spray the area to be sealed following the directions on the can. Once the coating has dried it can be over-painted with most acrylic paints. Full application instructions are available on the Crommelin website.Important notesThis product has not been tested for use in potable water systems, so do not use it on drinking water tanks or pipework. It is an exterior grade coating and is not designed as an under-tile or interior wet area membrane. Check the can and the manufacturer's data sheet for drying and recoating times and for surface or ambient temperature limits before starting.Specifications Brand Crommelin Product Sprayable Exterior Grade Waterproofing Pack 1 x 400ml aerosol can Colour White Type Rubberised waterproofing coating Application Aerosol spray (shake and spray) Overcoating Can be painted over with most acrylic paints Use Exterior Pack dimensions Approx. 64 x 64 x 197 mm SafetyThe can may burst if heated. Use only in well-ventilated areas, avoid breathing the spray, and keep away from heat, sparks, flames and other ignition sources. Wear gloves and eye protection, and remove any contaminated clothing and splashes from skin straight away. Store in a cool, dry place out of direct sunlight, do not expose to temperatures above 50°C, and keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$39.38
Crommelin Waterproofing Membrane Surface Primer is a rubber polymer primer and adhesion promoter made to prepare porous surfaces before Crommelin waterproofing membranes go on, supplied here in a 1L pack. It helps the membrane grip more reliably and firms up dusty, powdery substrates so the coating has a sound base to bond to.About the formulaA multipurpose rubber polymer primer designed to consolidate loose, chalky surfaces and improve membrane adhesion. Crommelin lists it as a one-coat product with high coverage and rapid drying, and describes it as non-toxic and low VOC. Its safety data sheet classes it as non-hazardous under the Safe Work Australia GHS criteria.Where to use itIndoors: concrete and cementitious floors and walls in wet areas that need priming before a Crommelin waterproofing membrane is applied.Outdoors: concrete and cementitious surfaces such as balconies and similar areas, prior to coating with a compatible Crommelin membrane.Suitable substrates are concrete and cementitious surfaces, including those that are dusty or powdery.How to use itPrepare the surface so it is clean, dry, sound and free of dust, grease and loose material. Apply the primer evenly, then allow it to dry before applying your Crommelin membrane. Full application rates, conditions and drying times are set out in Crommelin's instructions for the membrane you are using, so check these before you start.Important notesThis primer is intended for use with Crommelin waterproofing membranes, so confirm compatibility with your chosen membrane before you buy. Always follow the membrane manufacturer's surface preparation and moisture testing requirements. A small trial area is a sensible step before committing to a large job.Specifications Brand Crommelin Product Waterproofing Membrane Surface Primer Size 1L Base Rubber polymer Coats One coat Substrates Concrete and cementitious surfaces VOC Low VOC SafetyEven so, avoid contact with eyes and skin, keep out of reach of children, and use in a well-ventilated area. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Crommelin Shower Waterproofing Membrane is a ready-to-use, liquid-applied under-tile membrane for waterproofing showers and other wet areas before tiling, supplied here as a 1L pail for small jobs and repairs. It cures to a seamless, flexible waterproof layer with a textured surface that tile adhesive can grip, so you can tile straight over it.About the formulaA water-based, heavy-duty, modified rubber membrane that is applied wet and dries into a continuous film with no joins to leak. The manufacturer describes it as permanently flexible with high elongation, with excellent adhesion to the substrate and a keyed finish that promotes direct tile adhesion. It complies with AS 3740 (Waterproofing of domestic wet areas) and is suitable for use with cement-based tile adhesives that conform to AS 2358. It can be applied either below or above a screed.Where to use itIndoors: showers, bathrooms, laundries, kitchens and wet rooms, on both walls and floors, under tiles.Outdoors: balconies, under tile.Suitable substrates include concrete and masonry, cement renders and screeds, plasterboard and wet area plasterboard, compressed fibre cement sheet (suitably prepared), timber, plywood sheeting, wet area particleboard and steel. It is not suitable for use over white-set plaster.How to use it Prepare the surface so it is clean, dry, sound and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for 7 days. Fill any holes or honeycombing with a suitable repair mortar and remove high points so the surface is even, with a light texture. If the substrate is not dry, prime it with Crommelin Dampstop. If the surface needs more consolidation, apply one coat of Crommelin Powerflex first. The product is ready to use. Stir it well, then apply with a 75mm or 100mm membrane brush or a 230mm membrane roller cover. Apply only when surface and air temperatures are between 10°C and 35°C. The manufacturer's recoat time is about 2 hours and the tile-over time is about 48 hours. Follow the Crommelin technical data sheet for detailing at corners, joints and penetrations. Important notesOne litre produces about 1m² of finished membrane, which means building up the full film in the coats the technical data sheet specifies. Do not apply in conditions that are too hot or too cold. Make sure the substrate is properly cured and prepared before you start, because the membrane is only as good as the surface under it. For anything beyond a small area or minor repair, the 4L size may suit better. Check the current Crommelin data sheet for the full system and for the requirements that apply to your job.Specifications Brand Crommelin Product Shower Waterproofing Membrane Pack 1L pail Colour Green Base Water-based, modified rubber, liquid applied Application Brush or roller Coverage About 1m² of finished membrane per litre Recoat time About 2 hours Tile over About 48 hours Application temperature 10°C to 35°C Standards Complies with AS 3740; compatible with cement-based tile adhesives to AS 2358 Use Interior and exterior, under tile SafetyUse it with good general ventilation, avoid contact with skin and eyes, and wear suitable protective clothing. Do not let large spills reach drains or waterways. Store the pail in a cool, dry place out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$34.14
Crommelin Shower Waterproofing Membrane is a ready-to-use, water-based liquid membrane that waterproofs showers, bathrooms and other wet areas before tiling, supplied here in a 4L pail. It rolls or brushes on as a seamless, flexible layer and dries to a textured finish that tile adhesive can grip, so you can tile directly over it.About the formulaA heavy duty, modified rubber membrane in a water-based, ready-to-use form with no mixing. Once cured it stays permanently flexible and stretches well, so it can cope with small movements in the substrate. It sticks well to suitable surfaces. The keyed surface works with cement-based tile adhesives, and Crommelin states it suits all cement-based adhesives that meet AS 2358. It complies with AS 3740 (waterproofing of wet areas). The 4L pail makes about 4 square metres of finished membrane, which is enough for a standard single shower recess.Where to use itIndoors: under-tile waterproofing of shower recesses and bathrooms, on both walls and floors, and in other internal wet areas such as laundries.Outdoors: not specified by the manufacturer for this product. Check the Crommelin technical data sheet or contact Crommelin before using it on exposed external areas.Suitable surfaces listed by the manufacturer include concrete and masonry. Check the current technical data sheet for the full list of approved substrates, and confirm that wet area fibre cement, plasterboard or similar sheeting is approved before you start.How to use it Make sure the substrate is clean, sound and completely dry before you apply anything. Apply with a brush or a suitable membrane roller. Crommelin lists its Contractor Membrane Roller Cover as a compatible tool. At least 2 coats are required. Apply the second coat at 90 degrees to the first. Allow about 2 hours drying time between coats, as per the Crommelin how-to guide. Coverage is about 2 square metres per litre per coat. Complex or very irregular surfaces may need extra coats. Crommelin lists Dampstop, Reinforcing Fabric (with or without bond breaker), Polyurethane Sealant and Silicone WP Plus as compatible products for details and junctions. For a flood test, wait 48 hours, then pond water to a depth of 25mm for 2 hours. Remove the test water straight away afterwards. You can tile over the membrane after 48 hours. Clean tools and equipment with water before the membrane dries. Important notesFull cure takes 7 days. Do not apply to a damp substrate. Wet area waterproofing should be done to the requirements of AS 3740 and your local regulations, and many jurisdictions require a licensed waterproofer for the work. If in doubt, check before you start. This product is water-based, so keep the pail sealed and protect it from frost and extreme heat during storage.Specifications Brand Crommelin Product Shower Waterproofing Membrane Size 4L pail Colour Green Base Water-based, modified rubber Application Brush or roller, 2 coats minimum Coverage About 2 m² per litre per coat (about 4 m² finished membrane from 4L) Recoat About 2 hours Tile over / flood test After 48 hours Full cure 7 days Standards Complies with AS 3740; suitable with cement-based tile adhesives to AS 2358 Use Under-tile waterproofing of showers, bathrooms and wet areas, walls and floors Clean up Water, before drying SafetyAvoid contact with eyes and skin, and wear gloves and eye protection when applying it. Make sure the area is well ventilated while you work and while it dries. Keep out of reach of children. If it gets in your eyes, rinse with plenty of water. Refer to the Safety Data Sheet (SDS) for full details.
$93.15
![Crommelin Exterior Grade Brushable Waterproofer 1L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/crommelin-exterior-grade-brushable-waterproofer-1l-grey-2.jpg?v=1792410528&width=645)
Crommelin Exterior Grade Brushable Waterproofer is a grey, synthetic rubber based liquid membrane for areas that stay wet, including permanent immersion, protected pedestrian areas and surfaces that will be covered by a screed or topping. This 1L pail suits small repairs and compact jobs. It dries to a tough, flexible film that moves with the structure underneath.About the formulaA water based, ready-to-use membrane built on synthetic rubber (styrene butadiene rubber). The manufacturer describes it as low VOC and fast drying, with good adhesion to a wide range of building surfaces. It stays flexible after curing so it can follow structural movement, and it can bridge existing cracks up to 1.5mm. It is suitable for permanent water immersion and, per the manufacturer's technical data sheet, for collecting and storing potable water. Once cured it can be overcoated with screeds, renders and water based coatings.Where to use itIndoors: not intended as an interior wet-area (under-tile) membrane. Crommelin makes separate products for that job.Outdoors: gutters, roof gardens and terraces, podium decks and balconies, retaining walls, slab edges and fire tanks. It also suits non-exposed pedestrian areas and applications under screeds and toppings.Suitable surfaces listed by the manufacturer include concrete, brickwork, concrete blocks, cement render, screeds, fibre cement sheeting, plywood sheeting and steel (suitably prepared or primed). The technical data sheet also lists aluminium and lightweight aggregate block.How to use itSurfaces must be clean, dry and sound, and free of dust, grease, curing compounds, release agents, loose particles, efflorescence and laitance. Concrete should have cured for at least 28 days, and screeds and renders for at least 7 days. The manufacturer calls for a moisture test to confirm the substrate is dry enough to coat, and recommends an electronic moisture meter. Remove high points, fill blow-holes and honeycombing with a suitable repair mortar, and make good any defects. Masonry should be flush pointed.The product is ready to use, so stir it well before applying. Apply with a brush or roller. Use a bond-breaking sealant in all joints, junctions, protrusions, angles and internal corners, and apply the membrane to the positive side of the substrate. Apply two coats at the recommended rate, running the second coat at right angles to the first once the first is touch dry (about 2 hours). Apply only between 10°C and 35°C and in humidity no higher than 85%. Wash tools with water before the product dries.Important notesAllow a minimum of 72 hours before backfilling and about 7 days for full cure. Ensure good airflow while curing, and do not expose the membrane to moisture until it has fully cured. Protect the membrane from damage, and install suitable protection board before any backfilling. Do not apply in extreme weather or humidity. If the substrate is not dry, the manufacturer advises priming with Crommelin Dampstop, so check the full instructions on the Crommelin website for your substrate. Avoid applying the membrane too thickly in corners, as this can reduce flexibility. This listing is for the brushable (pail) product, not the sprayable aerosol version.Specifications Brand Crommelin Product Exterior Grade Brushable Waterproofer (Exterior Grade Waterproofing) Model number 1081-001 Pack 1L pail Colour Grey Base Water based, synthetic rubber (styrene butadiene rubber) membrane Application Brush or roller, 2 coats Coverage About 1.5m² per litre per coat, so about 0.75m² of finished two-coat membrane per 1L Crack bridging Existing cracks up to 1.5mm Recoat time About 2 hours Backfill Minimum 72 hours Full cure 7 days Application conditions 10°C to 35°C, humidity up to 85% Clean up Water, before the product dries Use Exterior, permanent immersion, non-exposed pedestrian areas, under screeds and toppings SafetyIt is stable under normal storage and use, and is incompatible with strong oxidising agents, strong acids and strong bases. Avoid contact with skin and eyes, wash tools and any spills with water while the product is wet, and store in a cool, dry place with the lid sealed. Refer to the Safety Data Sheet (SDS) for full details.
$34.76
Gripset Betta Bitumen Rubber is a two-in-one, solvent-free liquid membrane in a 1 litre pail, supplied here for waterproofing underground, immersed and general building work. Apply it as a bitumen polymer membrane, or dilute it with water to make an economical black bitumen paint where a full membrane is not needed.About the formulaA water-based, concentrated bitumen and latex polymer liquid that dries to a flexible black film. The manufacturer describes it as solvent free, with good sealing and adhesion on a range of building surfaces. It can be applied to damp surfaces provided there is no standing water, and it is approved for potable water contact (tested at an exposure of 1000mm2 per litre). Diluted 1:1 with water, 1L of concentrate makes 2L of bitumen paint.Where to use itIndoors: interior areas that need a waterproof or protective coating, where a membrane or bitumen paint suits the job.Outdoors: underground and retaining walls, garden beds, planter boxes and landscaped areas, fish ponds, stock troughs and water features, and general protective coating work. It also suits fully immersed applications when applied at the higher immersed coverage rate.Suitable surfaces include concrete, masonry, brick, timber, cement sheeting, metals and aged bitumen, along with other common building surfaces. If you plan to coat over existing paints or finishes, check with Gripset Betta first.How to use itStart with a clean, sound surface free of loose material and standing water. The product is self-priming. For porous surfaces, the manufacturer's literature suggests diluting the first coat with water (about 1 part concentrate to 3 parts water). Use a separate primer on non-porous or smooth surfaces and on surfaces affected by rising damp. Apply by brush, roller, trowel or spray, working each extra coat in a different direction to the one before.As a membrane, apply at least 2 coats at a combined minimum of 1.5 litres per square metre, which gives a dried film of about 1.2mm. For immersed areas, allow a minimum of 2 litres per square metre. Uneven or porous surfaces can need more. For paint use, mix the concentrate with clean water 1:1 by volume. Wash tools in water while the product is still wet.Important notesDrying times at about 20°C: tack free in 60 to 90 minutes, recoat after 2 to 4 hours, dry film in 24 hours, backfilling underground after 4 days, and immersed areas after 21 days. Temperature, humidity and surface porosity all change these times. Once dry, the product has to be removed mechanically or with solvent. For potable water use, wash the surface down and discard the first fill before using the water for drinking. At the minimum membrane rate, 1L covers well under 1 square metre, so check quantities before you buy.Specifications Brand Gripset Betta Product Bitumen Rubber Waterproofing Membrane Pack 1 litre pail Colour Black Base Water-based bitumen and latex polymer, solvent free Application Brush, roller, trowel or spray Membrane coverage Minimum 1.5 L/m2 in 2 coats (2 L/m2 for immersed areas) Paint dilution 1 part concentrate to 1 part water Tack free 60 to 90 minutes Recoat 2 to 4 hours Dry film 24 hours Immersed areas 21 days Clean up Water, while wet Use Interior, exterior, underground and immersed SafetyIt is non-flammable as supplied, but the dried film will burn in a general fire. Wash your hands after use and before eating, drinking or smoking. Do not let it enter drains, sewers or waterways. Refer to the Safety Data Sheet (SDS) for full details.
$27.04
Dunlop Pro Rapid Waterproofing is a water-based polyurethane-acrylic hybrid membrane made for programmes that cannot wait. As part of the Pro Rapid system with Dunlop Pro Rapid Tape, it allows tiling to begin just four hours after application, compressing what is normally a multi-day waterproofing stage into a single shift. It is a Class III membrane suited to both residential and commercial work, and it provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks. This compact pail suits ensuites, powder rooms and smaller wet areas.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries. Apply it to internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for at least 28 days, renders and screeds cured for at least 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted in ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the prepared substrate, seal junctions and penetrations with Dunlop Pro Rapid Tape, then apply the membrane in two coats, allowing the first to dry before recoating. Two coats are recommended for optimum performance. Tiling can commence 4 hours after the system is complete. Tools wash out in water.Important notesA final dry film thickness of 0.5mm is required on walls and floors. The product is certified to AS4858 and AS4654. Coverage varies with substrate porosity.Specifications Size 5kg pail Colour Light Blue Coverage Small pail covers approx. 4.3m² Tile after 4 hours (with Pro Rapid Tape) SafetyVentilate the work area, wear gloves and eye protection, and avoid skin and eye contact. Keep sealed and away from children; read the Safety Data Sheet before use.
$107.09
Dunlop Pro Rapid Waterproofing in the 20kg pail is the trade-scale version of Dunlop's fastest waterproofing membrane. A water-based polyurethane-acrylic hybrid, it forms a Class III membrane for residential and commercial wet areas and, when used with Dunlop Pro Rapid Tape, allows tiling to commence in just four hours. It also provides crack isolation protection over plastic shrinkage, hairline and other non-structural cracks, giving tiled finishes extra insurance against substrate movement.Where to use itAn internal membrane for bathrooms, showers, kitchens and laundries across whole houses, units and commercial fit-outs. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheet, wet area grade plasterboard, concrete cured for a minimum of 28 days, renders and screeds cured for a minimum of 7 days, PAA-branded internal structural plywood (marine or wet area grade, with shower areas sheeted using ceramic tile underlay) and internal AAC blocks and panels.How to usePrime the substrate, install Dunlop Pro Rapid Tape at all junctions, corners and penetrations, then apply the membrane in two coats, letting the first dry before the second goes on. Two coats are recommended for optimum performance. Once the system is complete, tiling can begin after 4 hours. Clean tools with water while the product is wet.Important notesA final dry film thickness of 0.5mm is required on walls and floors. Certified to AS4858 and AS4654. Coverage varies with the porosity of the substrate.Specifications Size 20kg pail Colour Light Blue Coverage Approx. 17.5m² per pail Tile after 4 hours (with Pro Rapid Tape) SafetyApply in a well-ventilated space wearing gloves and safety glasses. Avoid contact with skin and eyes, keep the pail sealed when not in use, and store out of reach of children. Refer to the Safety Data Sheet before starting.
$261.51
Dunlop Express Wet Area Tape is a self-adhesive waterproofing joint tape that seals the most leak-prone parts of a wet area, the joints where floor meets wall, and around shower grates and outlets. Simply peel and stick: no messy fillets, no waiting for a bond breaker to cure. Paired with Dunlop Express Wet Area Waterproofing membrane it forms a rapid, complete waterproofing system that lets tiling commence just four hours after the membrane goes on.Where to use itSuitable for indoor and outdoor wet areas including bathrooms, showers, laundries and balconies. It performs over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard.How to useMake sure surfaces are clean, dry and dust-free. Peel the backing and press the tape firmly along floor/wall junctions, corners and around penetrations such as shower grates and outlets. Where two lengths of tape meet, overlap them by a minimum of 15mm. Then apply Dunlop Express Wet Area Waterproofing membrane over the taped joints and the rest of the area as normal.Important notesA standard shower recess with 1.8m high walls needs roughly 7m of tape, so one 10m roll comfortably covers a typical shower. Used with the Express membrane, the system meets Australian Building standards for wet area waterproofing.Specifications Size 80mm x 10m roll Colour Grey Overlap Minimum 15mm at joins Substrates AAC, fibre-cement, concrete, renders, screeds, wet area plasterboard SafetyLow-hazard adhesive tape; use care with cutting tools and follow the safety directions of the waterproofing membrane applied over it.
$65.28
Dunlop Pro Rapid Tape is a self-adhesive sealing tape that delivers an instant waterproof seal across the joints where leaks start: the junction between floor and wall, and around shower grates and outlets in bathrooms, kitchens and laundries. It is the joint-sealing half of the Dunlop Pro Rapid system; team it with Dunlop Pro Rapid Waterproofing Membrane and tiling can commence just four hours after the membrane is applied, with the finished system meeting Australian Building standards for waterproofing.Where to use itDesigned for internal wet areas such as bathrooms, showers, kitchens and laundries. Suitable substrates include internal fibre-cement wall sheet, compressed fibre-cement sheets, wet area grade plasterboard, plywood, internal AAC blocks and panels, concrete cured for a minimum of 28 days, and renders and screeds cured for a minimum of 7 days.How to useEnsure the surface is clean, dry and free of dust. Peel the release liner and press the tape firmly into floor/wall junctions, corners and around grates and outlets, smoothing out air bubbles as you go. Then apply Dunlop Pro Rapid Waterproofing Membrane over the tape and the remainder of the area to complete the system.Important notesSubstrate curing times matter: concrete needs at least 28 days and renders or screeds at least 7 days before taping and waterproofing. This tape is intended for internal applications and is designed to work as a system with the Pro Rapid membrane.Specifications Size 75mm x 15m roll System partner Dunlop Pro Rapid Waterproofing Membrane Tile after 4 hours (as part of Pro Rapid system) SafetyLow-hazard self-adhesive product; take care when cutting lengths and follow the safety directions on the membrane used over it.
$98.41
Dunlop Express Wet Area Waterproofing is a high performance, water-based acrylic polyurethane membrane built for speed. Its high-build consistency lets you brush on a thick, even film that reaches the required membrane thickness with ease, and when used with Dunlop Express Wet Area Tape you can start tiling just four hours later. This handy 1kg tub is ideal for small repairs, patching and touch-up work, and it is backed by a 10 year guarantee.Where to use itUse indoors or outdoors in wet areas: showers, bathrooms, laundries and balconies. It adheres to AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard on walls and floors.How to usePrime the clean, dry substrate, seal junctions and penetrations with Dunlop Express Wet Area Tape, then brush on the first coat of membrane. Once dry, apply a second coat at right angles to the first until the required thickness is achieved. Tiling can commence after 4 hours when the full Express system is used. Wash brushes in water immediately after use.Important notesWaterproofing has minimum application requirements under AS3740: after two coats the dry film must be 1mm thick on floors and 0.5mm on walls. Check local council specifications before you begin. The membrane is a Class III membrane to AS/NZS4858.Specifications Size 1kg tub Coverage Up to 0.84m² on walls or 0.42m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyVentilate the area, wear gloves and eye protection, and avoid skin contact. Keep away from children and consult the Safety Data Sheet before use.
$43.00
Dunlop Express Wet Area Waterproofing in the 20kg pail is the full-bathroom format of Dunlop's fast-track membrane. This high performance, water-based acrylic polyurethane formula offers superior workability and a high-build film that reaches the required thickness without endless coats. Combined with Dunlop Express Wet Area Tape, the system lets tiling commence in as little as four hours, and it carries a 10 year guarantee.Where to use itMade for indoor and outdoor wet areas: showers, bathrooms, laundries and balconies. Apply it over AAC blocks, fibre-cement sheet, concrete, renders, screeds and wet area grade plasterboard, on walls and floors.How to usePrime the substrate with the appropriate Dunlop primer, seal all floor/wall junctions, corners and penetrations with Dunlop Express Wet Area Tape, then brush the membrane on generously. When the first coat is dry, brush on a second coat at right angles to the first to build the required film thickness. Tiling can begin after 4 hours when the complete Express system is used. Tools clean up in water while wet.Important notesAS3740 requires a minimum dry film thickness after two coats of 1mm on floors and 0.5mm on walls; confirm requirements with your local council. Certified as a Class III membrane to AS/NZS4858 and conforming to AS3740-2010 Wet Area Membranes.Specifications Size 20kg pail Coverage Up to 17m² on walls or 8.5m² on floors Colour Blue/Grey Tile after 4 hours (with Express Wet Area Tape) SafetyWork with good ventilation, wear gloves and safety glasses, and avoid contact with skin and eyes. Store sealed, away from children, and read the Safety Data Sheet first.
$313.95
Dunlop Waterproofing Reinforcing Mat is the quiet workhorse of a Dunlop waterproofing job. This 100mm wide fabric roll is embedded into the wet membrane at every corner, joint and crack, the places where movement and stress are most likely to open up a leak. By carrying the membrane across these weak points, it helps guarantee proper film thickness in the critical zones and lets you apply the second waterproofing coat immediately over the reinforced areas.Where to use itUse it indoors in wet areas as an integral part of the Dunlop waterproofing system, together with Dunlop Undertile Waterproofing. Reinforce wall/floor junctions, wall/wall corners, sheet joints, cracks, shower hobs and hob/floor joints, over metal or PVC angles, and along 90-degree external edges such as balcony perimeters.How to useApply the first coat of membrane to the junction, press a length of mat into the wet membrane so it sits flat without air pockets, then coat over the top so the fabric is fully saturated. The mat also acts as a carrier in awkward, hard-to-reach spots and smooths rough joints so the membrane covers evenly. Cut lengths with scissors or a utility knife as you go.Important notesThe junctions between wall and floor, hob and floor, and vertical corners where two walls meet should always be reinforced. The mat is a reinforcing component, not a standalone waterproofing product; it must be fully encapsulated in membrane.Specifications Size 100mm x 50m roll Use with Dunlop Undertile Waterproofing and Dunlop membranes Application areas Junctions, corners, joints, cracks, hobs, edges SafetyLow-hazard fabric product; take care when cutting and follow the safety directions of the membrane being used. A Safety Data Sheet is available from Dunlop Trade.
$67.73
Dunlop Undertile Waterproofing is a hard-wearing, highly flexible liquid membrane that forms a seamless waterproof barrier beneath tiles. Brushed on straight from the pail, its ready-mixed blue formula makes it easy to see your coverage as you build the film, and once cured it protects the structure beneath showers, laundries and balconies from moisture damage for the long haul.Where to use itDesigned for indoor wet areas such as showers, bathrooms and laundries, as well as balconies. It bonds to AAC blocks, bricks, concrete, renders, screeds, fibre-cement sheet, marine plywood and wet area grade plasterboard on both walls and floors.How to usePrime the prepared surface with the appropriate Dunlop primer, then brush on the first coat of membrane, embedding Dunlop Reinforcing Mat into wall/floor junctions, corners, hobs and joints while it is wet. Once the first coat has dried, apply a second coat at right angles to the first to reach the required film thickness, then tile over it with a compatible Dunlop tile adhesive.Important notesAustralian Standard AS3740 sets minimum membrane thicknesses: after two coats, the dry film must be at least 1mm on floors and 0.5mm on walls. Check your local council requirements before starting. The membrane is certified to AS4858 and AS4654.Specifications Size 12.5kg pail Coverage Approx. 10m² on walls or 4.5m² on floors per pail Substrates AAC, brick, concrete, renders, screeds, fibre-cement, marine plywood, wet area plasterboard Colour Blue SafetyEnsure good ventilation, wear gloves and safety glasses, and avoid skin and eye contact. Keep the pail sealed and stored away from children. Read the Safety Data Sheet before application.
$142.94
Dunlop Multipurpose Primer in the 4 litre pack is the job-sized version of Dunlop's water-based bonding primer, made for whole-room and whole-house preparation work. It improves the bond between the substrate and Dunlop floor levellers, renders, tile adhesives and waterproofing membranes, turning dusty, porous surfaces into a reliable base. It suits new and old concrete, particleboard and compressed fibre-cement sheets alike.Where to use itUse indoors or outdoors, on walls and floors. It is at home on fibre-cement sheeting, concrete slabs, masonry and lightweight concrete blocks, particleboard, renders and screeds, before levelling, rendering, tiling or waterproofing with Dunlop systems.How to usePrepare the surface so it is clean, dry and free of dust, grease and loose material. Pour out the primer and spread an even coat with a brush or roller, working it into the surface. Let it dry clear before applying the next product in your system. Wash tools in water immediately after use.Important notesOn very porous substrates a second coat is required to achieve a continuous primed film. The white-on, clear-dry formula shows exactly where you have coated. Actual coverage depends on substrate porosity and site conditions.Specifications Size 4 litres Coverage Approx. 6m² per litre (up to approx. 24m² per pack) Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyWear gloves and eye protection, keep the work area ventilated, and avoid prolonged skin contact. Keep away from children and refer to the Safety Data Sheet before starting.
$60.26
Dunlop Multipurpose Primer is a water-based primer engineered to strengthen the bond between a substrate and the Dunlop product applied over it. It is the go-to preparation step for flooring work, priming ahead of floor levellers, renders, tile adhesives and waterproofing membranes, and it performs equally well on new or old concrete, particleboard and compressed fibre-cement sheeting.Where to use itApproved for indoor and outdoor use on both walls and floors. Typical substrates include fibre-cement sheets, concrete, masonry and lightweight concrete blocks, particleboard, renders and screeds. Prime before levelling a slab, rendering a wall, waterproofing a bathroom or laying tiles.How to useSweep or vacuum the surface so it is clean, sound and free of dust, oil and curing compounds. Apply an even coat by brush or roller and allow it to dry clear before applying your leveller, render, adhesive or membrane. Because it is water-based, brushes and rollers wash out in water straight after use.Important notesVery porous substrates will drink in the first coat, so a second coat is required to build a proper film. The primer applies white and dries clear, making coverage easy to track. Coverage figures are a guide only and vary with surface condition.Specifications Size 1 litre Coverage Approx. 6m² per litre Substrates Fibre-cement, concrete, masonry, lightweight blocks, particleboard, renders, screeds Colour Applies white, dries clear SafetyKeep off skin and out of eyes, wear gloves, and ensure good ventilation while working. Store sealed and away from children. Consult the Safety Data Sheet for full handling guidance.
$34.59
Dunlop Primer & Additive is a ready-to-use liquid primer that boosts the grip between your substrate and the Dunlop products that go on top of it. Whether you are about to level a floor, lay tiles or roll out a waterproofing membrane, a quick coat of this milky-white liquid seals porous surfaces and gives adhesives, levellers and membranes a far stronger key to bond to. It doubles as a grout additive, improving flexibility, adhesion, colour depth and resistance to abrasion and staining.Where to use itSuitable for both indoor and outdoor projects, on walls and floors. Use it over concrete, cement sheet, fibre-cement, plasterboard, sheeting and timber before applying Dunlop tile adhesives, floor preparation products or waterproofing membranes.How to useMake sure the surface is clean, dry and free of dust or contaminants. Apply undiluted before waterproofing, tiling and timber floor preparation; dilute it for priming wall board. On large floor areas a household broom works well to spread the primer and push it into the surface. Allow it to dry clear before continuing with your adhesive, leveller or membrane. Tools rinse out in water while the product is still wet.Important notesCoverage varies with the porosity of the substrate. The primer goes on white and dries clear, so you can easily see where you have already coated. Highly porous surfaces may need extra material.Specifications Size 1 litre bottle Coverage Approx. 4m² per litre undiluted; approx. 8m² per litre diluted Substrates Concrete, cement sheet, fibre-cement, plasterboard, timber Colour Applies white, dries clear SafetyWork in a ventilated area, avoid contact with skin and eyes, and keep out of reach of children. Refer to the manufacturer's Safety Data Sheet before use.
$29.50
Stop leaks fast with Gorilla Patch and Seal Tape. This ultra thick, flexible sealing tape conforms to rough, uneven, and curved surfaces to create a strong, watertight barrier. Ideal for emergency fixes and long term maintenance around the home, workshop, caravan, and boat. Why you will love it Instant waterproof seal helps stop leaks on contact Works above or below the waterline for pools, gutters, and marine jobs UV and weather resistant for outdoor use Conforms and stretches to seal gaps, cracks, and seams Sticks to many surfaces including PVC, metal, plastic, glass, tile, and more Great for Repairing pinholes and cracks in gutters and downpipes Patching above ground pool liners and inflatable pools Sealing roof sheets, skylights, flashings, and RV seams Fixing garden hoses, buckets, and water features Temporary window and greenhouse repairs Surface compatibility Material Suitable Notes PVC, ABS, most rigid plastics Yes Clean and dry for best bond Metal, aluminium, galvanized steel Yes Remove rust and loose paint Glass, glazed tile, ceramics Yes Degrease surface Rubber, EPDM, vinyl Yes Press firmly to conform Textured masonry, concrete Yes Fill deep voids first for a flat seal Silicone coated or oily surfaces No Adhesion is limited How to use Prep Clean and dry the area. For underwater patches, wipe away algae or loose debris. Measure Cut a piece that extends past the damage by at least 25 mm on all sides. Apply Peel the liner and place tape over the damage. Start from the centre and work outwards. Seal Press down hard, removing air bubbles. Use a roller or rounded tool for maximum contact. Cure Initial grab is immediate. Full bond strength improves over 24 hours. Tips for best results Round the corners of the patch to reduce lifting For high pressure leaks, apply a larger patch or multiple layers Do not apply over active flowing water without reducing the flow first Frequently asked Can I use it underwater Yes. It can be applied to wet surfaces and submerged areas. Clean the surface as well as possible for the best seal. Is it paintable Most tapes are not paintable. If appearance matters, trim neatly and paint the surrounding surface instead. Is it a permanent fix It provides a durable seal for many applications. For structural or critical repairs, consider a permanent fix when practical. Good to know Temperature use range typically suits most Australian conditions Store in a cool, dry place and keep the roll protected from dust Glues Australia keeps Australia together. If you need help choosing the right sealing solution for your job, contact our team.
$57.40 $40.04
Selleys 635 Multipurpose Elastic Sealant Clear 290 mL Selleys 635 is a premium 100 percent clear elastic joint sealant that delivers strong, flexible and waterproof seals for indoor and outdoor jobs. Powered by hybrid technology, it adheres to most common building materials without primer and resists UV and weather for long lasting performance. Paintable with water based paints after skinning. Why you will love it Crystal clear finish that stays clear Excellent weather and UV resistance for exterior use Primerless adhesion to most surfaces Adheres to damp or wet surfaces Non slumping in joints up to 20 mm Low odour and low VOC, solvent and isocyanate free Paintable with water based paints once skinned Where to use Vertical and horizontal joints on most indoor and outdoor surfaces, including concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles, glass and many other common building materials. Not suitable for Polyethylene, Polypropylene or PTFE, structural glazing, or permanent water immersion. Directions Prep Clean and remove dust, grease and contaminants. Degrease metals. Cut nozzle on a sharp angle slightly wider than the joint. Use a suitable backing rod to control depth where required. Apply Gun the sealant into the joint. Tool within 10 minutes to ensure good contact with joint sides. Paint When skinned, paint with water based paints. For solvent based paints, first apply a water based undercoat and test on a small area. Clean up Clean spills and tools with mineral turps before cure. Once cured, remove mechanically. Storage Store below 30°C in a cool, dry place Unopened shelf life 12 months from date of manufacture Technical details Technology Moisture curing silyl modified polymer Colour Clear Packaging Cartridge 290 mL Density Approx. 1.05 g per mL Skin time at 23°C and 50 percent RH About 45 minutes Tack free time at 23°C and 50 percent RH About 60 minutes Cure rate at 23°C and 50 percent RH 2.5 to 3.5 mm per 24 hours Shore A hardness 35 ± 5 Tensile strength 1.7 MPa Elongation at break 240 percent Movement capability ± 12.5 percent Application temperature 5 to 35°C Service temperature ?20 to 70°C VOC content Approx. 35 g per L VOC classification Meets Green Building Council of Australia limits for general purpose and architectural sealants Good to know Better extrudability and curing from 5°C and above Non bubbling and non slumping formulation Sandable when fully cured Limitations Not for permanent water immersion Not for Polyethylene, Polypropylene or PTFE Not for structural glazing Follow all safety directions. For first aid and handling information refer to the product SDS.
$20.74
Selleys Auto Fix Windscreen Sealant 100 mL - Black Stop leaks fast around windscreens and windows with a durable, weather resistant silicone seal. Selleys Auto Fix Windscreen Sealant forms a waterproof barrier that resists vibration, UV and temperature extremes, keeping water, dust and drafts out. Why choose this sealant 100 percent neutral cure silicone for reliable sealing Forms a waterproof seal to stop leaks quickly UV and weather resistant for long term performance Skins in 5 minutes and is touch dry in about 30 minutes Handles joint movement up to 25 percent Suitable surfaces Glass and windscreens Rubber surrounds and trims Painted surfaces and most plastics Metal frames and channels Typical applications Sealing between windscreen glass and rubber Sealing between rubber and metal frames Stopping minor water ingress around vehicle windows General sealing where a flexible, black silicone finish is desired Key specifications Technology Neutral cure silicone Colour Black Movement capability Up to 25 percent Skin time About 5 minutes Set time About 30 minutes Full cure Approximately 24 hours Service temperature -40°C to 180°C Application temperature -20°C to 50°C VOC 26 g/L Pack size 100 mL tube Directions Remove any dirt or moisture between the rubber and glass, or rubber and metal. Clean with mineral turpentine and allow to dry. Remove cap, unscrew nozzle, pierce inner seal, refit nozzle, then cut the tip at a 45 degree angle. Insert the nozzle between the rubber and glass or rubber and metal where possible. Squeeze the tube with steady pressure to push sealant into the joint. Smooth off with a gloved finger. If additional smoothing is needed, do it before the sealant skins. Clean up uncured sealant with mineral turpentine. Cured material must be cut or scraped away. Replace the cap after use. Allow sealant in the nozzle to cure, then remove before next use. Handy tips For neat lines, mask both sides of the joint and remove tape before the sealant skins. Best results occur when the joint is clean, dry and free of loose material. Limitations Not recommended on natural rubber, NBR or chloroprene neoprene due to poor adhesion. Clean up and storage Clean uncured sealant with mineral turpentine. Remove cured sealant by cutting or scraping. Store in a cool, dry place below 30°C. Use within 24 months of production. What you get 1 x Selleys Auto Fix Windscreen Sealant 100 mL - Black
$23.08
Dunlop FC Joint Sealant Dunlop FC Joint Sealant is a premium, ultra flexible, moisture curing polyurethane sealant designed for jointing fibre cement, blueboard and compressed fibre cement sheets. The non slump formula handles joints up to 40 mm wide with a movement capability of plus or minus 25 percent. It is easy to apply, solvent free and isocyanate free. Colour: Grey. Why choose this sealant High flexibility for dynamic joints Non slump for clean, accurate beads on vertical and horizontal surfaces Solvent free and isocyanate free Paintable after curing Reliable performance supported by a 10 year guarantee Ideal uses Joints in fibre cement, blueboard and compressed fibre cement sheets Facade and cladding joints where movement is expected General building joints up to 40 mm width Compatible surfaces Adheres to most common construction substrates, including: Fibre cement sheets and blueboard Precast concrete panels, blockwork and bricks Sandstone and granite Fibreglass Plasterboard Technical details Movement capability ± 25% Joint width Up to 40 mm Skin time Approximately 35 minutes at 23°C and 50% RH Tack free time Approximately 1 hour at 23°C and 50% RH Cure rate About 2.5 mm per 24 hours at 23°C and 50% RH Application temperature 10°C to 35°C Clean up Warm water immediately after use Shelf life 12 months unopened, stored cool and dry Finish Paintable when dry. Can be overcoated with paint or texture coats. Colour Grey Surface preparation Ensure surfaces are clean and dry, free of dust, oil, grease, salt, mould, release agents and any contaminants that may affect adhesion. Mask adjacent areas to keep lines neat. Follow sheet fixing instructions from the board manufacturer. How to apply Cut the nozzle at a sharp angle slightly wider than the desired bead or joint width. Use a suitable backing rod where required to control depth. Aim for a joint depth equal to half the joint width. Gun the sealant into the joint and tool within 10 minutes using a round spatula to ensure full contact with the joint sides. Curing times increase in cold or humid conditions. Safety and handling Avoid contact with skin and eyes. Wear protective gloves, clothing and eye protection. Ensure adequate ventilation during application. Keep out of reach of children. Refer to the product SDS for full safety guidance. Guarantee Backed by a 10 year guarantee when used as directed.
$21.58
Selleys Roof and Gutter Silicone Selleys Roof and Gutter Silicone is a neutral (non-acid) cure 100% silicone sealant designed for most building surfaces, including metals, tile, cement sheeting, PVC, and Colorbond® roofing. It is available in a range of colours to match your roof and gutters. Features UV and weather-resistant Superior waterproof seal - superior adhesion and resistant to lifting, provides a long-lasting, flexible seal Non-corrosive neutral cure formula Superior flexibility with +/- 25% movement capability Temperature resistance: approximately -60°C to +150°C Suitable for contact with drinking water - complies with AS/NZS 4020# 25-year guarantee* against crumbling, cracking, and peeling away Available in a range of Colorbond® colours to make it easier to select the right colour for the job Cured sealant at area to volume ratios up to 2500mm²/L Where can this product be used? Metal and tile roofing All metal lap-joint waterproofing Colorbond roofs and fences Guttering and flashings Vents and downpipes Weatherproofing caravans and trucks Copper, brass, and zinc Skylights What materials is this product suitable for? Aluminium Sheet Metal Copper Brass Zinc Galvanised Metals Rigid PVC and most plastics, including polystyrene Rubber Glass Terracotta Concrete Glazed tiles BlueScope Steel decorative sheet metals such as Lysaght Zincalume and COLORBOND®
$50.18
High-Grade Neutral Cure Silicone A high-grade neutral (non-corrosive) cure silicone formulated for superior adhesion to cement (e.g., grout). The product also contains a fungicidal protector for excellent mould and fungal resistance. Features Superior adhesion to mortar, grout, and metals. As the product does not lift at the edges and adheres so well to cement and grout, dirt, mould, and fungus will not become trapped, preventing unsightly black mould spots. Superior silicone formulation forms a durable seal that locks out water and does not shrink when drying. Built-in fungicide to inhibit the growth of mould. Available in a range of colours to suit most wet areas. Non-corrosive neutral cure formula. Low odour, so can be used in any environment without discomfort. Easy to clean once applied, as it resists moisture, hot cooking oils, and steam. Superior flexibility with +/- 25% movement capability and up to 400% elongation or stretch. Temperature resistance: approximately -60°C to +150°C. 25-year guarantee – when used as directed, i.e., for private use and within 12 months of purchase, the product is guaranteed against crumbling, cracking, or drying. Where can this product be used? Showers and sinks Metal, copper, and brass fittings Perfect for use on or around: Showers Baths Spas Sinks Plumbing Fixtures Can not be painted over. Not suitable for building materials that bleed oils or solvents, such as impregnated wood. Not for use on polyethylene, polypropylene, or Teflon. Pre-test plastics before use. What materials is this product suitable for? Ceramic, glazed & porcelain fixtures Metal, copper, and brass fittings Plastic laminates Rubber Glass Stainless steel Concrete and grouts Many plastics including polystyrene How to use this product Thoroughly clean and dry the surface from oil, dirt, and grease with Mineral Turpentine first and then Methylated Spirits. Allow to dry completely before applying silicone. If there is old silicone that needs to be removed, we recommend using SELLEYS SILICONE REMOVER. This ingenious product makes removing old silicone easy. We also recommend sanding the surface back with a good quality sanding block, such as a ROTA COTA Sanding Block Medium/Course Grain, as the silicone will adhere more readily to a scratched-up surface. Ensure you tape both sides of the gap before applying the product. This ensures a neat finish and makes it easier to clean up. Cut the seal at the top of the cartridge and cut the nozzle at a 45° angle, to the size of the gap opening. Fit the nozzle to the top of the cartridge. Insert the cartridge into a caulking gun such as the SELLEYS LIGHT SPEED Caulking Gun. We recommend this caulking gun, as its new innovative pressure release design reduces the mess from run-on and stress on your hands, which is critical if you are doing a lot of sealing. Hold the caulking gun at a 45° angle. Press the nozzle opening against the joint, apply steady pressure to the caulking gun, and extrude the silicone sealant. Move in a pushing motion along the joint in one smooth action. For a smooth finish, smooth with a finger dipped in mineral turpentine or, for a professional finish, use a paint scraper such as a 50mm ROTA COTA Soft Grip Scraper dipped in mineral turpentine. Excess sealant must be cleaned up before it skins in 5-10 minutes. Wipe excess away with a cloth dampened in mineral turpentine or use a SELLEYS Hand Kleen Wipe. Remove tape before the sealant skins. Clean tools immediately with mineral turpentine. Avoid smearing on surrounding surfaces. The sealant will cure fully in 72 hours. At this point, any unwanted sealant can be removed by trimming with a sharp blade, but avoid undercutting the seal. Handy Tips Ensure you tape both sides of the gap before applying the product for a neat finish and easy cleanup. When first applying, extrude a small amount onto a piece of scrap material to ensure a smooth continuous flow of silicone sealant. Remove the tape before the silicone sealant skins. For a better finish, complete painting prior to using the sealant as it cannot be painted over. Use a spatula dipped in mineral turpentine or detergent and water to tool off the sealant for a better finish. Work in sections that can be completed before the sealant skins. Tooling off and tape removal must be completed before skinning occurs for a better finish. Keep a pack of SELLEYS Hand Kleen Wipes handy to wipe up spills and clean any material off the skin before it cures. SafetyTips Uncured product may irritate eyes. Avoid contact with skin. If contact occurs, wipe off immediately and wash with detergent. It may irritate sensitive skin. Refer to the Safety Data Sheet (SDS) for full details.Storage and Re-Use Store in cool dry conditions, below 30°C. The sealant should be used within 6 months after opening. After use, keep the nozzle on the cartridge. Silicone is a reactive product and cures once exposed to humidity. For longer storage periods, leave the nozzle on and place plasticene or Blu Tack over the end of the nozzle. Tightly tape a piece of aluminium foil over the whole nozzle to exclude any air. When re-using, simply remove the foil and plug from the old nozzle, pull out the excess silicone, and re-pierce the tip of the cartridge. If cure has occurred inside the cartridge, the product is no longer usable and should be discarded.
$51.50
Dunlop Roof Repair Waterproofing Adhesive 310ml Seal, stick and stop leaks on the spot. This highly flexible, silane modified adhesive and sealant bonds and seals even in wet conditions, making it a smart fix for urgent roof, gutter and pond repairs. Why you will love it Works in the wet and can be applied underwater for minor repairs Flexible waterproof seal for joints, cracks and patches Strong adhesive grab for quick spot fixes Paintable once cured to match surrounding surfaces Low mess clean up while wet Ideal surfaces Concrete, wall panels, timber, waterproofing membranes, ceramic tiles, aluminium, plastics, metal, polystyrene foam, glass and glazed tiles. Typical uses Emergency roof and gutter leak sealing Sealing laps, flashings and penetrations Pond edge and minor underwater touch ups General crack and joint sealing around the home Spot fixing where fast, reliable adhesion is needed Directions Prep: Ensure the surface is firm and free of dust, oil and loose residues. Slightly damp surfaces are acceptable. Load: Remove the aluminium seal, pierce the nozzle membrane, fit and trim the nozzle, then place the cartridge in a caulking gun. Apply as a sealant: Gun a continuous bead over the joint or crack and allow to cure. Apply as an adhesive: Gun bead lines or spots, then press parts together within 7 to 10 minutes at 23°C, before skinning starts. For spot fixing, keep glue points 25 to 30 cm apart. Clean up: Wipe away any excess while wet with a clean cloth. Good to know Application temperature: 5°C to 35°C Dry and cure times vary with substrate and climate. Higher humidity shortens open time, lower humidity extends it. Colour: Grey. Can be over painted once dry. Always test paint compatibility on a small area first. Shelf life: 12 months in unopened packaging stored in a cool, dry place Packaging: 310 ml cartridge Safety Wear gloves and eye protection. Avoid inhaling vapours and ensure good ventilation. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details. Warranty Backed by a 10 year product guarantee when used as directed. This is in addition to your rights under the Australian Consumer Law. Notes Do a trial application for underwater or constantly wet repairs, as long term stability depends on the specific situation. Not for chemical resistant applications. Remove any skinned layer in the nozzle before reusing an opened cartridge.
$21.97
Gorilla Ultimate Strong Wood Glue 532 mL is a reliable high performance wood glue for interior and exterior carpentry chosen for home repairs, trade work, and craft builds when you want a bond you can trust. Designed for Australian conditions, it balances strength, ease of use, and clean application so you can get professional results without special tools. The 532 mL pack is ideal for general work and keeps neatly in a toolbox or caddy. Why choose Gorilla Ultimate for your next project Everyday jobs often involve mixed materials and imperfect surfaces. Gorilla Ultimate Strong Wood Glue 532 mL has been formulated to wet out well, grab quickly, and cure to a tough finish that resists movement and contact stress. It maintains bond integrity across common temperature swings and has dependable resistance to moisture and most household chemicals. Whether you are fixing, building, sealing, or assembling, this product gives you confidence from first squeeze through final set. Best for Furniture build and repair Edge bonding and laminations Cabinetry and joinery where water resistance is valued Suitable surfaces The adhesive works well on the following surface types when properly prepared: Hardwoods and softwoods Plywood and MDF Veneers and end grain with correct technique Surface preparation Good preparation is the key to a long lasting repair. Remove loose material, dust, and grease. Wipe glossy areas with methylated spirits or an approved cleaner and allow to dry. On very smooth plastics and metals, lightly roughen with fine abrasive paper to give the adhesive a mechanical key. Dry fit parts first and mark alignment points so you can assemble accurately within the open time. If bonding porous materials, ensure both faces are dry and free of surface chalking. How to use Check fit and plan clamping. Do a trial run without adhesive so you know the order of steps. Apply a thin, continuous bead to one surface. For wide pieces, use a zig zag pattern to maximise wetting. Bring surfaces together within the stated open time of typically 5 to 10 minutes depending on temperature. Reseat once if needed, then hold steady. Apply even pressure using clamps, tape, weights, or temporary fasteners. Avoid squeezing all adhesive out of the joint. Allow to cure undisturbed. Initial handling strength will develop as the adhesive sets, with a full cure reached based on the chemistry described below. Cure profile Open time allows assembly before clamping. Forms a strong cross linked bond that is water resistant when fully cured. Temperature and environmental performance Use above 10 C and avoid freezing conditions while curing. Avoid application to very cold, sweating, or waterlogged surfaces. For outdoor use protect fresh bonds from rain until the skin has formed and the core has progressed in cure. Once fully cured, the bond resists normal weathering, splash water, and intermittent UV exposure based on the substrate and paint systems used. Clean up and finishing Wipe squeeze out with a damp cloth while wet. Scrape or sand once cured. When cured, excess can be carefully trimmed or sanded. For painted finishes, allow the adhesive to fully cure before priming. Test paint on a small area to confirm compatibility and drying behaviour. Coverage guide Coverage varies with bead size, surface porosity, and technique. As a general guide, a 3 mm bead yields approximately 10 to 12 linear meters per 310 mL cartridge. Smaller packs scale proportionally. Gaps, rough edges, and highly absorbent materials will reduce coverage. Plan an extra margin for offcuts and practice passes. Tips for best results Work within the recommended open time so the adhesive can properly wet the surfaces. Use light clamping pressure to keep parts aligned while maintaining a film thickness for strength. For very porous substrates, apply a thin precoat as a primer layer and allow it to tack before final assembly. Keep joint lines clean by masking edges with painter tape and removing it before the adhesive skins. Where movement or vibration is expected, design the joint to share load across a large area. Troubleshooting Poor adhesion: Check for oil, release agents, or surface dust. Reclean and lightly abrade if necessary. Slow cure: Low temperature and low humidity extend cure time. Maintain moderate conditions for best results. Visible squeeze out: Wipe fresh material with a suitable solvent and a soft cloth. Once cured, trim carefully. Bond line prints through paint: Allow a full cure, then prime and apply thin coats of paint, allowing proper drying between coats. Storage and shelf life Close the cap tightly and store upright. Do not allow the nozzle to clog; remove dried film if present. Always check the pack for a lot code and use by guidance. Reseal immediately after use and store upright. Dispose of empty containers responsibly. Safety Read the label before use. Wear gloves when handling uncured material. Provide ventilation in enclosed areas. Avoid contact with skin and eyes. Keep out of reach of children and pets. If sensitivity occurs, stop use and seek advice. Do not ingest. First aid directions and detailed handling information are available on the package and the safety data sheet. Frequently asked questions Can I bond dissimilar materials? Yes, provided each surface is clean and sound. Differences in expansion are managed by the adhesive film thickness and the inherent flexibility after cure. Is clamping required? Light clamping improves alignment and final strength. Excessive pressure can starve the joint of adhesive which reduces performance. Is the bond water resistant? Once cured the bond resists splash water and routine humidity. For permanent immersion choose an adhesive designed for underwater service and follow the manufacturer guidance. Planning your job Measure twice and cut once. Dry assemble parts so you can confirm squareness and alignment before adhesive is involved. Keep rags, clamps, and spacers ready. If you are new to the product, test on offcuts to get a feel for bead size and squeeze out. A consistent 1 to 2 mm bond line is a good starting point for most rigid materials. Thicker lines help when surfaces are uneven. Avoid starving the joint by pressing too hard without giving the adhesive a place to reside. Responsible use Choose an adhesive that suits the materials and the environment the finished piece will face. If a joint will be submerged, carry structural loads, or be exposed to strong chemicals, check the technical data sheet for specific guidance. Many general purpose products are perfect for day to day work, while specialised tasks call for a system designed and tested for that environment. Using the right product first saves time, money, and rework. Aftercare and maintenance Adhesive joints are remarkably strong when used correctly. Design repairs so that routine loads are shared across a generous area. Where heavy vibration is present, pair the adhesive bond with appropriate mechanical fasteners. Keep cleaning chemicals mild, and avoid abrasive pads on visible joints. If a bond will be repainted, choose flexible paint where movement is expected, and keep edges sealed to prevent dirt tracking along the bond line. Recycling and disposal Allow empty containers to cure before disposal. Check local council guidance for recycling of plastics and metal cartridges. Never pour uncured product into drains or soil. Wipe tools on scrap material and let residue harden before placing in general waste. Smart handling keeps the workspace clean and reduces environmental impact.
$25.20
Overview This high-quality general-purpose silicone sealant is a versatile solution for a wide range of sealing and bonding applications. Engineered with neutral cure technology, it is designed to provide a durable, flexible, and weather-resistant seal that remains reliable even in demanding environments. Once cured, the sealant forms a strong rubber-like finish that is permanently elastic, ensuring long-lasting performance both indoors and outdoors. Key Features Neutral Cure Technology: Low-odor curing system suitable for sensitive applications. Permanently Flexible: Retains elasticity over time without cracking or shrinking. Waterproof Protection: Provides a watertight seal, protecting against leaks and moisture ingress. Interior & Exterior Use: Unaffected by rain, snow, extreme temperatures, or prolonged UV exposure. Excellent Adhesion: Bonds strongly to most common building materials without primer. Easy Application: Smooth flow from the tube, easy to tool and clean before curing. Applications This sealant is designed for general-purpose use across a variety of materials and environments. Its flexibility and adhesion make it suitable for: Sealing around window and door frames. Lap joints in metal guttering and roofing sheets. Bonding panels such as wood, plasterboard, insulation board, and drywall. Fixing masonry joints including sills, brickwork, and decorative trims. Gap filling around pipes, conduits, and penetration surfaces. General sealing in kitchens, bathrooms, and living areas where flexibility is required. Limitations Not suitable for permanent water immersion (e.g., underwater joints or continuous water load). Not recommended for use on polyethylene (PE), polypropylene (PP), polycarbonate (PC), polymethyl methacrylate (PMMA), PTFE, neoprene, bituminous surfaces, or very soft plastics. Not intended for deep cavity filling without adequate moisture for curing. Surface Preparation To ensure maximum performance, surfaces must be clean, dry, and free from dust, grease, or loose particles. Non-porous surfaces should be wiped with solvent and dried with a clean cloth. Porous surfaces should be lightly abraded or brushed to remove contaminants and improve adhesion. Complete any painting work before applying the sealant. Application Instructions Remove the cap and pierce the nozzle seal. Apply steadily along the joint or surface, ensuring continuous contact. Smooth or tool the bead before skin formation occurs. If masking tape is used, remove immediately after tooling to avoid tearing the cured seal. Curing At room temperature (23°C), the sealant will skin over within 15 minutes and achieve full cure within 24 hours, depending on humidity and joint depth. Once cured, it provides a permanently flexible and weatherproof joint. Cleaning & Maintenance Excess uncured sealant can be cleaned using a cloth dampened with mineral turpentine. Fully cured material should be trimmed away carefully with a sharp blade. Store unused tubes in a cool, dry place below 25°C and away from direct sunlight. Shelf life is up to 12 months from the date of manufacture. Health & Safety Use in a well-ventilated area. Avoid contact with eyes and mucous membranes, as uncured sealant may cause irritation. In case of contact with eyes, flush thoroughly with water and seek medical advice. Keep out of reach of children. Always follow safety instructions and refer to the product’s safety data for detailed guidance. Why Choose This General Purpose Silicone Sealant? This sealant is a trusted choice for tradespeople, DIY enthusiasts, and homeowners seeking a reliable solution for everyday sealing needs. Its combination of flexibility, adhesion, and weather resistance ensures that once applied, it continues to protect and bond effectively for years to come. Whether you are fixing a leaking gutter, sealing around windows, or bonding decorative trims, this product provides professional results with minimal effort. Technical Specifications Technology Neutral Cure Silicone Appearance Clear Paste Working Time Up to 15 minutes Tack-Free Time Approximately 15 minutes Full Cure at 23°C 24 hours Flexibility Permanently elastic after curing Weather Resistance Unaffected by rain, snow, UV, and temperature variations Applications Windows, doors, guttering, masonry, panels, pipes, decorative elements Storage Below 25°C, out of direct sunlight Shelf Life 12 months from manufacturing date
$9.98
![Sika Sikaflex Pro+ Sealant 310ml [White]](http://gluesaustralia.com.au/cdn/shop/files/4520524025.jpg?v=1754724135&width=645)
Sikaflex® Pro+ - Solvent-Free, Highly Flexible Sealant & Adhesive All new solvent-free, highly flexible, primer-less sealant and adhesive is the one-stop product for any tradesman and handyman's home building or renovation. Sikaflex® Pro+ is a 1-component moisture curing polyurethane elastic sealant and adhesive that is formulated with Sika’s newly engineered i-Cure technology to provide higher performance, more movement capability, and improved bubble-free curing. Sika’s new i-Cure technology is user and eco-friendly, with no solvents and a low environmental impact, while maintaining the performance of traditional polyurethane. It is suitable for overpainting with traditional paint coatings. The i-Cure® technology has an early initial set and overcomes bubbling in the sealant while curing, even in extreme conditions. Sikaflex® Pro+ is a high-performance, interior and exterior elastic joint sealant with excellent water, weather, and ageing resistance. It has many uses, including: Expansion joints in walls and cladding Sealing around doors and window frames Sealing penetrations in walls and floors for pipes Sealing joints in concrete and masonry elements Sealant for draught-proofing and general sealing and filling applications Pro+ can be used on a multitude of applications and common building substrates. It has good adhesion to damp substrates. To name a few, Pro+ can be used on: Aluminium Steel Powder-coated metals or glazed tiles Concrete, aerated concrete, cement-based renders, mortars, and bricks Application of Sikaflex® Pro+ Ensure all surfaces are structurally sound, clean, dry, and free from any grease, etc. (The surface can be damp but not wet. If uncertain, apply masking tape to test adhesion. If masking tape sticks to the surface, it's OK to proceed.) Movement joints must have a minimum width and depth of 5mm. Apply a bond-breaker tape, or backing rod to the base of the joint to prevent 3-sided adhesion. To keep the work clean, apply masking tape to the top edge of the joint on each face. Cut the nozzle to the required width and gun sealant into the joint. Avoid voids or air entrapment in the joint when applying. Before the sealant has skinned, tool off with an appropriate spatula to give a smooth finish. Remove the masking tape and clean up immediately.
$24.00
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Black]](http://gluesaustralia.com.au/cdn/shop/files/9300697125187.jpg?v=1754724132&width=645)
![Selleys Solar Flex UV Protection High Performance Sealant 445g [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697125200.jpg?v=1754724131&width=645)
Selleys SolarFlex Selleys SolarFlex provides protection from ultraviolet (UV) radiation and other harsh weather elements. Harsh Australian and New Zealand conditions make the choice of an effective solar/weather protection solution critical. Features Superior weather protection Long-lasting flexibility No primer required before painting Watertight seal with a 10-year guarantee* Adhesion to wet or damp surfaces Non-bubbling Better curing and extrudability (>5°C) with no slump Paintable with water-based paints after product skins in 60 to 90 minutes Low VOC** Where can this product be used? Skylights Walls Patios Floors Fencing Windows What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics* *Not suitable on polyethylene, polypropylene, or Teflon. Application Instructions Ensure substrates are clean and free of oil, grease, or loose particles. Cut the seal and nozzle, then fit it to the cartridge and place it in the caulking gun. Hold the caulking gun at a 45° angle and gun the sealant ahead of the nozzle, ensuring the product is pushed into the joint. For neat joints, use masking tape on both sides of the joint and remove it before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g., polyethylene backer rod) and appropriate joint width/depth. See the technical datasheet for more information. Limitations Not suitable on polyethylene, polypropylene, or Teflon. Cure excess product before disposal. Not for permanent water immersion or below water-line use. For water immersion, please use Selleys Marine Flex.
$23.92
![MaxisiL A Silicone Sealant [Colour: A28 Brown]](http://gluesaustralia.com.au/cdn/shop/files/693_720.jpg?v=1754724110&width=645)
![MaxisiL A Silicone Sealant [Colour: A29 Havana]](http://gluesaustralia.com.au/cdn/shop/files/9326816000715.jpg?v=1754724111&width=645)
The Premium Wet Area Sealant Wet areas Baths, showers, toilets Easy to use Contains strong fungicides to fight mould Maxisil A Ceramic Silicone is an acetic cure silicone recommended for all ceramic tile areas, especially for expansion joints in bathrooms, kitchens, and flooring sectors. Built-in fungicides for mould resistance For both exterior and interior use Excellent weatherability, resistant to ageing and UV radiation Resistant to chemicals and temperature Primerless adhesion to clean, dry surfaces such as ceramics, glass, acrylics, aluminium, and painted wood Very good tooling and smoothing properties Time-saving with an easy cleanup system Please note that colour samples are not true to the actual colour. This is a guide only. Characteristics 1-component acetate-curing silicone sealant Excellent weathering, ageing, and UV resistance Enables a great finish, will not string during application Good tooling and smoothing properties Contains fungicides Medium skin formation time for easy handling Very good adhesion on ceramic substrates Primerless adhesion to many substrates Stress expansion modulus at 100% (DIN 53 504, S3A): 0.3 N/mm² Meets DIN 18545, part 2D (German industrial standard) Available in a variety of colours (custom colours available upon request) Fields of Application Sealing connection joints between ceramic tiles, showers, baths, and flooring sections Expansion/movement joints in bathrooms and wet areas Connection joints on door and window frames Sealing double-glazing joints Glass block glazing Sealing general building substrates Suitable for interior and exterior use Important Information Before application, ensure materials in the contact area are compatible with the sealant and with each other to prevent damage or discoloration. If in doubt, consult the manufacturers of surrounding substrates. While curing, small amounts of acetic acid are released — ensure good ventilation After curing, the product is odourless and harmless Thicker silicone layers require longer vulcanisation time Not for full-surface bonding unless construction prerequisites are met For layers over 15mm, contact our technical department Avoid contact with bitumen-containing materials or those releasing solvents (e.g. butyl, EPDM, neoprene, bituminous paints) When replacing mould-contaminated joints, remove all old sealant and treat areas with Maxisil Anti-Mildew Spray Technical Properties Skin-forming time (23°C / 50% RAH) ~ 15 min Curing in 24h (23°C / 50% RAH) ~ 2–3 mm Processing temperature +5°C to +35°C Viscosity (23°C) Pasty, stable Density (23°C, ISO 1183-1) ~ 1.0 g/cm³ Shore A hardness (ISO 868) ~ 20 Permissible movement capability —
$22.50
Ultra high-strength 2-component epoxy adhesive for the heaviest loads (up to 1700 N/cm²). Working time: 90 minutes, handling strength: 6 hours, final bond: 24 hours. Can be drilled, sanded and painted. Resistant to impact, ageing, dampness, heat and cold. Suitable for metal, stone, concrete, marble, china, wood, glass, duro-plastics, glass-fibre reinforced plastics, rigid PVC and Styrofoam.* Not suitable for PE, PP, PS, soft PVC. UHU Epoxy Quick Set High-performance 2-component epoxy adhesive for quick and reliable repairs. Dries clear. Working time: 5 minutes, handling strength: 20 minutes, final bond: 12 hours. Resistant to impact, ageing, dampness, heat and cold.
$8.57
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/040074023437N_e5aad737-db85-4e62-bf16-291c599f76e3.jpg?v=1754716410&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [27.4m]](http://gluesaustralia.com.au/cdn/shop/files/04007_dddd7c02-55b5-4bc6-ae35-61e0db1a57f7.jpg?v=1754716410&width=645)
$33.09
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/040074023512N_8cc2a3d8-5590-4ec5-b8db-e3c56c98ba43.jpg?v=1754716404&width=645)
![T-Rex Ferociously Strong Tape UV Resistant With Knit Cloth [10.9m]](http://gluesaustralia.com.au/cdn/shop/files/04007.jpg?v=1754716404&width=645)
$16.48
T-Rex® Brute Force® high-performance duct tape is a bold next step in tape technology. Built with Forge-Link™ Technology, an extreme tensile cloth, one loop of T-Rex Brute Force tape holds 700+ pounds of weight, making it the strongest duct tape on the market, period. Too tough to tear by hand, this premium tape features an aggressive double-thick adhesive with a durable waterproof backing, so you can secure, fasten or hold all sorts of materials for any project, on any job site. Hold more. Do More.™ T-Rex Brute Force. FEATURES: Extreme tensile strength 1 loop of tape holds 700+ pounds of weight Made with patented Forge-Link™ Technology Waterproof backing High tack, double-thick adhesive that sticks to rougher and dirtier surfaces, withstands severe pressure UV resistant materials
$36.00
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530329_412e3d45-40a8-4eca-9ed6-191f389472d4.jpg?v=1754716380&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [White x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_0ee281c8-0366-40a5-bb6c-b1a12d613ac2.png?v=1754716380&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1002_13c9931e-09ce-4d00-a35f-0df6977453aa.jpg?v=1754716370&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Red x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_54ba8b96-b758-4a94-8ba2-6b524d94e6ea.png?v=1754716370&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/949_1003_d0705a81-d0df-43a8-b8d2-cd06f5c78769.jpg?v=1754716354&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Clear x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_733528b0-7c24-46e0-889e-87698aafcb17.png?v=1754716354&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$16.96
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/9315284530305_0485e2cc-4f7e-46c2-94ae-dee297210481.jpg?v=1754716346&width=645)
![Tommy Tape Self Fusing Silicone Tape Seals And Repairs Waterproof Insulates [Black x 3m]](http://gluesaustralia.com.au/cdn/shop/files/93152845_50821584-e9cf-45b6-9528-1e997cfe48d7.png?v=1754716346&width=645)
Tommy Tape® Self-Fusing Silicone Tape The next generation of tape is here — premium, adhesive-free repair and sealing tape for fast fixes at home, on the job, and on the road. Tommy Tape self-fusing silicone tape saves time and money across plumbing, electrical, automotive, marine, garden, and industrial jobs. Unlike vinyl or cloth tapes, it uses no adhesive. Instead, it chemically bonds (self-fuses) to itself on contact to form a tough, flexible, and permanently water-tight wrap — even underwater. Why you’ll love it Extreme temperature range: operates from −65 °F to +500 °F (approx. −54 °C to +260 °C). Electrical safety: insulates up to 8,000 V per layer (typical PVC electrical tape ≈ 600 V). Leaves no residue: no adhesive means no sticky mess when removed. Weather- & waterproof: seals within seconds; ideal for outdoor and marine use. Flexible & form-fitting: stretches over 300% to wrap irregular shapes, fittings, and bends. Built to last: resists UV, oil, salt, and common chemicals; helps combat corrosion. Popular uses Plumbing: emergency seals on copper, PVC, and garden hoses; patch vacuum and pool hoses. Electrical: bundling and insulating leads, wire harnesses, extension-cord strain relief (power off first). Automotive & 4×4: wrap frayed looms, protect hoses, create quick roadside fixes. Marine: mast boot wraps, deck-side waterproofing, salt-spray protection. Tools & grips: re-grip shovels, rakes, wheelbarrows, gym dumbbells, walking canes. Sports & DIY: re-grip golf clubs, tennis/pickleball paddles; improve wheelchair and shower-chair grip. Home & garden: weatherproof outdoor cables, protect back-yard gear and appliances. Industrial: protective wraps on fittings, temporary containment where adhesives aren’t suitable. How to apply (best results) Prep: Turn power/water off where applicable. Clean and dry the area if possible. Start & anchor: Peel off the liner, stretch the tape as you begin to wrap, and press the starting end onto itself to anchor. Stretch & overlap: Stretch to at least 2× its length (more stretch = stronger fuse). Overlap each wrap by ½ width. Build layers: Add additional layers for higher pressure, stronger seals, or increased dielectric protection. Finish: End the wrap on itself and press firmly. Full fusion develops quickly; handle with care while it sets. Remove: Cut off (do not unwind) when it’s time to replace — it leaves no residue. Specifications Material Silicone rubber (self-fusing) Adhesive None (bonds to itself on contact) Dielectric Strength Up to 8,000 V per layer (build layers for higher insulation) Temperature Range −65 °F to +500 °F (approx. −54 °C to +260 °C) Resistance UV, oil, salt, weather, and common household/automotive chemicals Water Performance Weatherproof & waterproof; can be applied underwater in many scenarios Elongation Stretches over 300% for tight, conformal wraps Removal Cut off to remove; no sticky residue Colours / Sizes Varies by SKU (see options above) Better than traditional tapes Feature Tommy Tape Self-Fusing Silicone Vinyl / Cloth Electrical Tape Adhesive No adhesive (self-fuses) Pressure-sensitive adhesive (leaves residue) Waterproof Seal Yes — seals in seconds; can be used underwater Limited; adhesive can lift when wet Dielectric Strength Up to 8,000 V per layer Typically ~600 V Temperature Range −54 °C to +260 °C Narrower range; softens or becomes brittle UV/Chemical Resistance Excellent (UV, oil, salt, chemicals) Moderate; can degrade outdoors Residue on Removal None — clean cut-off Commonly leaves sticky residue FAQs Can I use it on live electrical circuits? No. Always switch power off before wrapping. Build sufficient layers for the required insulation, and follow local electrical standards. Will it stick to wet or oily surfaces? Because it bonds to itself (not the substrate), it can often be applied in damp or even underwater situations. For best results, clean and dry the area first. Is it reusable? Once fused, it forms a single mass. Cut it off to remove; it won’t unwind. Apply a fresh wrap if needed. What isn’t it for? Not a substitute for permanent structural repairs. Avoid use on fuel lines or high-pressure systems without proper engineering sign-off. Notes: Performance values are typical and depend on application method, substrate, and number of layers. Always test on a small area first. Follow safety guidelines for electrical and pressurised systems.
$23.24
Single Use Waterproof Epoxy Adhesive is the perfect product to use when you need to do any marine or waterproof projects. It works under or in the presence of water and remains waterproof. Package contains just the right amount of product for most small projects. The metal tubes dispense effortlessly and are easy to mix. This product sets in only 3-4 hours.
$29.00
You have seen 192 out of 277 products
Keep water out of joints, seams and enclosures with waterproof and weatherproof products. Match cure type and flexibility to the application (bathroom, kitchen, outdoor). Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
