Flexiseal FC is a fast curing polyurethane Adhesive and Sealant with high flexibility and excellent adhesion. Waterproof+, suitable for indoor and outdoor applications^, paintable after it has cured. Best for : Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. Product Details Where can this product be used? External wall and cladding joints Weatherproofing joints between brickwork, masonry, wood concrete or metal frames Joints in walls, balconies, around window or door frames Joints in bridge and balcony parapets Retaining walls Roofing Acoustic rated walls What materials is this product suitable for? Common building materials such as concrete, brick, masonry, ceramic tile, metals, softwood, hardwood and some plastics*. *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. How to Use AS AN ADHESIVE: Apply a bead or small blobs on surface. Assemble parts together and clamp firmly to hold until cured. Remove excess immediately. Initial bond achieved in 24 hours depending on temperature and humidity. Bond strength increases over a few days. AS A SEALANT: Extrude sealant into the joint ensuring full contact with the sides of joint. Avoid entrapment of air. Smooth sealant with spatula forcing it into the joint. For best performance, install joint backing rod (polyethylene or polyurethane foam rod) in the joint to control depth and ensure joint movement. Suitable for +/- 25% joint movement. Complies with ISO11600/F/25HM. Limitations: *Will not adhere to PE, PP or PTFE–test other plastics and rubber first. ^To maximise durability in outdoor applications paint with a suitable exterior paint. Some colours may discolour after exposure to UV radiation. +Not suitable for permanent water immersion or below water line use. Clean Up Mineral turps. Cured product can only be removed mechanically
$25.37
![Selleys Armour Flex High Performance Adhesive [Grey]](http://gluesaustralia.com.au/cdn/shop/files/9300697125279_ca037dae-5a32-46a8-b3b3-d4b80d5f85fd.jpg?v=1754711933&width=645)
Selleys ArmourFlex provides superior strength with instant grab and more flexibility than conventional adhesive/sealants. Features Superior strength & instant grab No primer required Watertight seal with a 10-year guarantee* Can be applied to wet or damp surfaces with excellent adhesion Non-bubbling Better curing and extrudability (>5°C) Easily paintable with 2 coats of water-based paints after product skins in 60 to 90 minutes Sandable Low VOC** Long-lasting flexibility Fast curing No slump Trafficable Potable water approved AS/NZS4020 (Area to volume ratios **Meets GBCA limits for general purpose and architectural sealants. Where can this product be used? Skylights Walls Patios Floors Fencing Windows Expanding joints in concrete What materials is this product suitable for? Concrete Timber Metals Cement sheeting Brick Plasterboard Ceramic tiles Fibreglass Most plastics (Pre-test before use. Not for polyethylene, polypropylene or Teflon.) Ensure substrates are clean and free of oil, grease or loose particles. Cut seal and nozzle and fit to cartridge, then place in caulking gun. Hold caulking gun at 45° angle and gun sealant ahead of nozzle ensuring product is pushed into joint. For neat joints, use masking tape on both sides of the joint and remove before skinning. Tool with a soapy solution before skinning occurs. For optimal joint design, use non-absorbent backing material (e.g. polyethylene backer rod) and appropriate joint width/depth. See technical data sheet for more information. Limitations: Not suitable on polyethylene, polypropylene or Teflon. Not for permanent water immersion or below water-line use. In dry conditions, surfaces can be misted with water to speed up cure. Paint with water-based paint. A minimum of two coats are necessary to ensure proper wetting out the sealant surface
$45.65
![Selleys 401 Silicone Adhesive for Gaskets Resists 205 Degrees [Clear]](http://gluesaustralia.com.au/cdn/shop/files/8755f41ba29a40388c0684d41f7eeeda.jpg?v=1757753359&width=645)
Silicone 401 RTV is a one part ready to use, acid cure, room temperature vulcanising (RTV), silicone adhesive sealant. It cures rapidly on exposure to atmospheric moisture to form a versatile, durable, resilient silicone rubber. It is available in clear. Uses Silicone 401 is suitable for form-in-place gaskets and for adhesive, sealing and electrical insulating applications in manufacturing and plant maintenance. Technical Features Wide Temperature Tolerance: Remains permanently flexible under operating temperatures from – 60oC to 205oC, and will tolerate short periods of 260oC Good Chemical Resistance: Good resistance to most organic and inorganic chemicals, solvents and oils Primerless Adhesion: Adheres without primer to many metal, glass, ceramic, rigid plastic, rubber painted and wood substrates Non-toxic: Suitable for incidental food contact in food handling equipment and food contact surfaces Excellent Weatherability: Excellent resistance to ozone, UV light and ageing Good Electrical Insulating Properties: Insulating properties are comparable to other insulating rubbers at room temperature, though performs better than many other rubbers at higher temperatures and water has little effect on these properties Application Tips Not recommended for use with petrol, distillate and some other hydrocarbon solvents. These can cause softening and swelling which is undesirable in some applications. Do not use in totally confined joints where sealant is not exposed to atmospheric moisture Chemical compatibility should be tested for each application under consideration Cannot be over-painted Technical Details and Performance Indicative information only, not to be used for setting specifications. Typical Application Properties Consistency Non – sag, gun grade Tack Free Time (25oC, 50% r.h.): 15 – 20 minutes Skin Forming Time 5 to 10 minutes (depending on weather conditions) Cure Time (3mm Section @ 25oC, 50% R.H.): 24 hours Shrinkage During Curing Approximately 3.5% by volume Specific Gravity 1.04 Storage Life (Below 30oC in original unopened container):12 months Typical Mechanical Performance Properties (3 day cure @ 25oC, 50% R.H.) Tensile Strength (MPa) 1.2 Ultimate Elongation % 400 Hardness (Shore A) 25 Tear Strength (N/mm) 5.0 Joint Movement Capability ± 25% Typical Electrical Properties (at Room Temperature) Dielectric Strength kv/mm 21 Dielectric Constant @50Hz to 5MHz 2.6-2.8 Dissipation Factor Tan @50Hz-5MHz 20×10-4 to 5×10-4 Volume Resistivity (ohm-cm) 1×1013 (wet 60oC) 1×1014 (dry 23oC) Typical Thermal Properties Brittle Point –60oC Maximum Continuous Operating Temperatures 205oC Maximum Intermittent Operating Temperatures 260oC
$28.49
![RiteTack Power-X Construction Adhesive Sealant 290ml [White]](http://gluesaustralia.com.au/cdn/shop/files/8711595195942_51a4eb7a-99ab-421a-98a2-8d45cb2f05e6.png?v=1754712003&width=645)
High initial tack and high strength White colour Works with virtually all materials 290ml tube For professional and DIY use Power-X is a versatile adhesive and sealant. It is a one-component, high-modulus composition, and it cures under the influence of humidity. It is free from isocyanates and silicones, and perfect if you are in need of an adhesive/sealant with high resistance to aging and weathering, that still maintains a high tack and high adhesion strength. Used on polystyrene, coachwork, roofing, timber, shipbuilding, DIY, and more. Power-X is a professional series product from the Rite Adhesives range. It has been specially developed for high-quality work. Power-X is also the ultimate glazing sealant for all your glass surfaces. It’s a premium, high-quality sealant that retains elasticity to ensure a seamless bond between your glass and other surfaces. It also has a durable weatherproof finish, making it perfect for humidity-prone areas, like the kitchen, bathroom, or pool. Plus, it’s super easy to apply. It is perfect for virtually any sealing, bonding, and filling applications on almost any surface, in interior or exterior settings, making it one of the most versatile products available at Rite Adhesives! One feature of Power-X is its permanent elasticity. Excellent adhesion in most applications, including as glazing sealant. Works with MDF, brick, and concrete. Also, natural stone, ceramic tiles, and aluminium. Works with metals like steel and stainless steel, brass, zinc, and copper, and most plastics and ABS. Power-X can be painted with water-based paints and several other systems! Due to its high flexibility (400% elongation at break!), it will absorb the movement of the materials onto which it is applied.
$15.95
Quickset WATERCRETE Is a unique product that provides a simple, fast, concrete solution to a multitude of awkward repair problems large and small…from re-forming grating ledges to repairing the Owen Falls Dam in Uganda. Quickset WATERCRETE is a multi purpose patching cement that sets in five minutes …even underwater! Bonds to concrete, masonry, wood, steel and glass fibre. Quickset WATERCRETE is an all purpose patching and bonding compound which is very effective where the presence of water makes repairing and sealing difficult. It will repair leaks in pools, tanks and bonds earth ware pipes and tiles, without the need to drain the water. It is ideal for repairs in wet or dry situations where delays are inconvenient as it can be walked on, or driven over in 30 minutes. Quickset WATERCRETE is a fast setting, high compressive strength compound that shows its initial set in 4-6 minutes, even underwater. It reaches maximum compressive strength in 24 hours and bonds to CLEAN CONCRETE, MASONRY, STONE, TIMBER and STEEL. Contains no calcium chloride. It is suitable for use with drinking water. BRIEF TECHNICAL SPECIFICATIONS Initial set 5 minutes. Curing set 15-30 minutes. Compressive strength of 2,000psi or greater in 24 hours Maximum strength in 28 days Non-toxic Volume change: Expansion after 24 hours 0.1% Contraction after 28 days 0.01% Water absorption 1.7% after 14 days Factory Production to BS 5750 Part II BONDS TO: CEMENT TIMBER MASONRY FIBREGLASS STEEL INSTRUCTIONS FOR USE Remove all loose material from the area to be treated to ensure a solid bond. Slowly add one part of water to 4 parts Quickset WATERCRETE and mix for 1 to 2 minutes to the CONSISTENCY OF PUTTY. Add more product if mix is too wet as wet mix seriously reduces effectiveness. Avoid contact with skin. Press the mix firmly into the prepared area. The product can be moulded to shape. When filling a hole against running water, hold the mixed product in position with a trowel or piece of timber until it cures. The product hardens rapidly after 4 minutes. If sealing a leak underwater, increase the size of the hole on the surface to create a taper. Before applying Quickset WATERCRETE to dry work, generously soak the location with water. Damp conditions assist curing. For repairs less than 1.5cms thick in a dry situation, it is best kept damp for 24 hours.
$101.37
Polishes internal furniture & joinery that has been previously waxed or oiled Suitable for Timber, concrete, slate, terracotta and stucco All-natural ingredients Apply with a lint-free cloth Polishes internal furniture and joinery that has been previously waxed or oiled. Rejuvenates french polished/lacquered items and leather items. Uses: Also suitable for sealing and polishing slate, terracotta and stucco Coverage: Up to 40m² Apply with: Lint-free cloth Number of coats: 2 Sheen level: Pale Satin
$32.95
PC-Metal™ Putty Epoxy replaces metal. Mix with fingers and apply. Quickly PC-Metal™ cures to reattach metal (30 min). Cures hard, fast, nonconductive. Contains metal – sticks to metals such as cast iron, zinc, aluminium, stainless steel, steel and copper. Here are just a few specific uses (there are hundreds of other uses): Replace broken knob on a drill press Insulate wire connections, secure wire nuts Rebuild and repair zinc or aluminium gear housing Fill abandoned drill holes in aluminium or steel Seal stainless steel electrical panel Stop leaking drum How to prepare a surface for bonding with PC-Metal™ Remove contaminants such as dust, dirt, oil and grime with a solvent such as denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner. Mild detergent solution in water is also good removing contaminants. Use a clean paper towel or rag for wiping. Remove rust and loose paint with sandpaper or wire brush. Epoxy typically sticks to most paints. If there is a concern of the paint’s adhesion then remove it with sandpaper, wire brush or paint stripper. Smooth, glossy and shiny surfaces should be roughened using sandpaper to increase adhesion. Adhesion to wet or damp surfaces can be improved by wiping with alcohol. Do not use mineral spirits or paint thinner for removing contaminants. How to clean-up after PC-Metal™ application We recommend wearing disposable gloves when mixing and applying epoxy putty. Remove from skin with soap and warm water. Clean up mixed epoxy before it cures with paper towels and solvent. Denatured alcohol (ethanol), acetone, rubbing alcohol (isopropyl alcohol) or lacquer thinner are suitable solvents for removing uncured epoxy. Cured epoxy can be physically removed by prying off with a screwdriver or pliers. It can also be removed with paint stripper or remover. Can PC-Metal™ plug a hole in a 55 gallon drum? PC-Metal™ is an excellent product for quickly plugging a hole made in a drum. PC-Metal™ has a strong odor. Does the smell go away? PC-Metal’s™ odour stops after it cures. PC-Metal™ is dark gray, dense and hard when cured. Is it as strong as metal? PC-Metal™ is a product that is designed to look like and cure hard like metal. It is excellent for bonding and filling metal objects but is not as strong as steel, aluminium and other metals. How fast does it cure? How much should be mixed? PC-Metal™ is very fast curing. It is important to mix small portions for 45 to 60 seconds and immediately apply to the surface. Within 3 to 5 minutes PC-Metal™ cures very hard. In less than 60 minutes PC-Metal™ reaches its full hardness. What kind of metal is in PC-Metal™? Does PC-Metal™ rust? It is an alloy of iron and aluminium. It will not rust. Can PC-Metal™ be machined? Can it be tapped or cut? Cured PC-Metal™ can be drilled and cut. Tapping threads in PC-Metal™ is not advised. It is better to set the bolt or threads in the mixed PC-Metal™. Coat the threaded screw or bolt with release agent if it needs to be removed. Can PC-Metal™ be used to seal a cracked engine block? PC-Metal™ has many automotive uses even repairs to engines.
$16.17
![Parfix Kitchen Bathroom Silicone Sealant [Clear]](http://gluesaustralia.com.au/cdn/shop/files/9300697115935_9d24cb9e-09d9-43f4-8d51-2c3a3b021f3d.jpg?v=1754712259&width=645)
Sanitary grade silicone Acetic cure Excellent adhesion Watertight seal Parfix Bathroom And Kitchen Silicone cures to produce a watertight seal and contains agents to resist the growth of mould and fungus. This white coloured sanitary grade sealant is most suited to use on shower recesses, splashbacks, bathtubs and vanities.
$10.61
Parfix Glass Silicone Black: Unmatched Bonding for All Your Glass Needs Key Features Excellent bond to glass Acetic cure for optimal sealing Designed for interior and exterior use UV resistant and shrink-proof Specifications Colour Black Model Name Parfix Window and Glass 300g Model Number 9300697122445 Material Silicone polymer Paintable No Stainable No UV Resistant Yes Outdoor Yes Indoor Yes Shrink Resistant Yes Sandable No Applications Suitable for use on windows, glass partitions, and glass blocks. Instructions For optimal results, apply on clean, dry surfaces. Follow safety guidelines for acetic cure silicones.
$12.48
![Monarch Mini Silicone Mould Resistant [Translucent]](http://gluesaustralia.com.au/cdn/shop/files/9320090029073_9b2a79dd-e58b-4fb6-a3b1-d6525871d967.png?v=1754712303&width=645)
![Monarch Mini Silicone Mould Resistant [Translucent] (2)](http://gluesaustralia.com.au/cdn/shop/files/monarch-mini-silicone-mould-resistant-translucent-2.png?v=1792405534&width=645)
Monarch Mini Silicone is the sealant for your home. Especially useful in kitchens, bathrooms and laundries where sinks, baths, vanities and showers are installed and other outdoor patio areas, this durable polymer creates a waterproof barrier that'll stand up to wear-and-tear while resisting heat or cold when conditions change outside. A versatile property for any project you're working on! Monarch Mini Silicone sealant is ideal for kitchens, bathrooms and laundries, where sinks, baths, vanities & showers are installed & for other outdoor uses. Available in a variety of colours. FEATURES Premium quality 100% silicone Ideal for wet areas Indoor and outdoor use Maximum flexibility BENEFITS Proven to last in all weather Mould resistant Tack free in 10 minutes Monarch Mini™ is an innovative range of sealants, fillers, adhesives and accessories for the sealant market. This range of products brings a much easier way to apply sealants or adhesives compared with using traditional products. The Monarch Mini’s unique and compact sealant cartridge features a shorter length and a smaller diameter, making it easier to control and apply. Reaching into tight spaces where conventional caulking guns can’t, Monarch Mini’s lightweight and superior handling make it more practical and easy to use. In addition to the Monarch Mini cartridge range are nozzles and caulking guns, which capitalise on the shorter cartridge and increase the places where it can be used. Filled with only premium quality materials, the Monarch Mini™ range is suited to both the DIY market and sections of the trade market, making Monarch Mini a very versatile option.
$6.28
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions: Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiselling, scraping or picking. The dried glue will not damage tools.
$10.86
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Silver]](http://gluesaustralia.com.au/cdn/shop/files/052427607126N_cffee80a-3f6c-4f18-ab8b-4a06da2ea9e8.jpg?v=1754712484&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$14.60
![Gorilla Tape Incredibly Strong Extra Thick Weather Resistant 11m x 48mm [Black]](http://gluesaustralia.com.au/cdn/shop/files/052427600127N_b3248bad-00e4-4a61-873b-21199bac68a6.jpg?v=1754712486&width=645)
Gorilla Tape has taken duct tape to a new level. Gorilla Tape's toughness surpasses ordinary tapes, making the list of uses virtually endless. Made with double thick adhesive, strong reinforced backing, and a tough all-weather shell, it’s the biggest, strongest, toughest thing ever to happen to tape. It sticks to rough and uneven surfaces, including wood, stone, stucco and brick, that ordinary tapes can't hold. To us, it’s made the way tape should be: The Toughest on Planet Earth. Directions Use like any other tape. Tear Gorilla Tape by hand or cut to size with a knife or scissors. Apply the tape carefully, smoothing out any pockets or rolls. That’s it. Enjoy the strength and durability of Gorilla Tape! Does freezing/thawing affect Gorilla Tape? No, if Gorilla Tape freezes, it will work just fine once it returns to room temperature. What temperature range does Gorilla Tape require? Gorilla Tape works best at temperatures above 32°F (0°C). For best results, always apply the tape at room temperature. How do I store Gorilla Tape? To retain adhesive quality, store Gorilla Tape in a cool, dry place. Keep out of direct sunlight. Try storing the tape vertically (rather than laying flat), on a hook or on wax paper. If you have multiple rolls, keep your excess supply wrapped until they’re needed. Can I remove Gorilla Tape? Gorilla Tape can be removed, but with some difficulty and it may leave some residue. To remove any excess residue, we recommend using the tape itself as a blotter. How do I use Gorilla Tape? Surfaces should be clean and dust-free. We recommend rubbing the tape into the surface. This will help achieve a better bond. Can it be used instead of electrical tape? Gorilla Tape should not be used as electrical tape. Will Gorilla Tape work on rough surfaces? Yes! Gorilla Tape is designed to stick to rough surfaces including wood, stucco, plaster, brick, metal and more. Gorilla Tape is manufactured with a highly concentrated rubber based adhesive – two to three times as thick as traditional duct tape. The result is a tape that fills gaps and penetrates rough surfaces. It is important to clean the surface and brush off any loose particles and dirt before applying Gorilla Tape. Who should buy Gorilla Tape? Anyone who wants a quality tape that will last longer and holds stronger. 1. Do-it-yourselfers who know their labour justifies the use of better tools and materials. 2. Professionals who know quality materials affect a business reputation. 3. The “just-give-me-the-best” kind of person – someone with demanding applications or where re-taping is difficult. Is Gorilla Tape waterproof? We’ve found that Gorilla Tape will last a lot longer than regular duct tapes when it comes in contact with moisture. Make sure the surface is dry before you apply the tape, and we’re sure you’ll find this out for yourself. Does Gorilla Tape use Gorilla Glue as the adhesive? No, they are two different adhesives. Gorilla Glue is a polyurethane glue and the adhesive used on Gorilla Tape has been specially formulated for tape. What’s the difference between Gorilla Tape and regular duct tape? We took ordinary duct tape and made it better. We made it twice as thick and we use 2 to 3 times the amount of rubber based adhesive.
$15.51
Introducing Gorilla All Weather Tape - Your Ultimate Outdoor Repair Companion! When it comes to outdoor repairs, ordinary tapes just won't cut it. That's where Gorilla All Weather Tape steps in! Engineered with unbeatable strength and a weather-resistant shell, this tape is the ultimate solution for all your outdoor repair needs. Brace yourself for the power of Gorilla All Weather Tape! This incredible tape is equipped with a permanent, low tack adhesive that bonds with tenacity. No matter the challenge, it holds strong and steadfast, making sure your repairs stand the test of time. Rain or shine, Gorilla All Weather Tape delivers exceptional performance. Its waterproof design resists drying, cracking, and peeling caused by sunlight, heat, cold, and moisture, making it ideal for extreme weather conditions. Experience the versatility of Gorilla All Weather Tape! It works effortlessly in both hot and cold temperatures, ensuring it remains your reliable partner no matter the season. Ease of use? Check! Applying Gorilla All Weather Tape is a breeze. Simply tear it by hand or cut it to size with a knife or scissors. Carefully apply the tape, smoothing out any pockets or rolls, and voilà! You're all set to enjoy the strength and durability of Gorilla Tape! For optimal results, ensure the surface is clean, free of dust, dirt, and debris. Store the tape flat on a non-delicate surface, keeping it away from direct sunlight. Technical Specs: Application Temperature: Above 4° C Service Temperature: -17° C to 93° C Indoor: Yes Outdoor: Yes Moisture Resistant: Waterproof Frequently Asked Questions: Q: Can Gorilla All Weather Tape be used instead of electrical tape? A: Gorilla All Weather Tape should NOT be used as an electrical tape. Q: Will Gorilla All Weather Tape work on plastic/vinyl/rubber? A: Yes, Gorilla All Weather Tape contains a highly concentrated rubber-based adhesive and sticks to most plastics, including polyethylene (PE) and polypropylene (PP). However, it does not work on materials with high oil or plasticizer content, such as EPDM rubber or PVC. For those materials, we recommend using an acrylic tape like Crystal Clear Gorilla Tape. Q: Is Gorilla All Weather Tape food safe? A: Gorilla All Weather Tape is not recommended for direct or indirect food contact and should not be considered food safe. When it comes to outdoor repairs, don't compromise. Choose the unmatched strength and durability of Gorilla All Weather Tape. Tackle any challenge, withstand any weather - trust Gorilla to get the job done right!
$35.99
The product that started it all. Original Gorilla Glue built a name for itself with its incredible, industrial holding power and versatility. Water activated, it expands into materials to form an incredibly strong bond to virtually anything. Gorilla Glue is your solution for almost any project or repair. It’s 100% waterproof, safe for indoor and outdoor use and strong enough to stand up to the elements. Plus, its expansion allows it to penetrate the glued surface for a superior bond. Sand it, paint it, stain it. Simply stated, it’s the Toughest Glue on Planet Earth. Directions Prepare and Dampen the Surfaces If you’re using Original Gorilla Glue for the first time, or bonding a new type of material, we always recommend trying a test piece first. Prepare your surfaces: All surfaces must be clean, dust free and tight fitting. For shiny surfaces, such as metals, glass and some plastics, roughen up the material to give the glue something to bite into. Damp It: Lightly dampen one surface with water. We recommend using a damp cloth or spraying with water. Do not saturate the surface. For dense hardwoods, lightly dampen both surfaces prior to gluing. Evenly Apply Gorilla Glue Onto the Dry Surface Glue It: Carefully apply onto the dry surface. Do not over apply. We recommend wearing gloves or spreading the glue with a disposable brush. In some instances, Gorilla Glue can be a skin sensitizer. If you are predisposed to skin reactions, please take the extra precaution. If you do get the glue on your skin, try removing it with a dry cloth or paper towel first (particularly if the glue is still tacky). If that doesn’t work, try washing with soap and cold water, or using an exfoliator with a gritty texture. Dry your skin and apply lotion. We do not recommend using any kind of alcohol or acetone. This actually strips the skin of its natural oils, which means the glue is more likely to stick. Clamp the Two Surfaces Together Tightly Clamp It: Make sure the clamping pressure is distributed evenly across the surface. Or, if you don’t have a clamp, use heavy objects or Gorilla Tape® to achieve the appropriate clamping pressure. For lighter objects, try using rubber bands to hold the pieces together tightly. Clamp objects for 1–2 hours. For best results, allow 24 hours to cure. Clean up If you need to remove any uncured “squeeze out” or wet glue, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure to read and follow directions if using a paint thinner. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Storage Tips After each use, wipe the bottle’s lid and nozzle clean with a dry cloth. For 2 oz. bottles, tightly replace the lid after wiping clean and store in a cool, dry place. For bottle sizes 4 oz. and larger, we suggest squeezing excess air out of the bottle. While still squeezing, tightly replace the cap and then store in a cool, dry place. This helps eliminate moisture in the bottle. You should expect a year shelf life. What is the temperature range for applying the glue? For best results, apply the glue at room temperature. Original Gorilla Glue should be left out of reach of children and animals. Can you speed up the curing process? Original Gorilla Glue should be clamped for 1–2 hours. During this time, it reaches 80% cure. Allow 24 hours for 100% cure. Note that cure time can vary depending on temperature, humidity and the porosity of the bonding materials. Is Gorilla Glue truly 100% waterproof? Yes. Gorilla Glue is 100% waterproof. It passes ANSI/HPVA Types I and II. How do I extend the shelf life of Gorilla Glue? Gorilla Glue is moisture activated. Once the adhesive comes in contact with moisture, it can start to harden. To extend the shelf life, always wipe lid and nozzle clean with a dry cloth and tightly replace the lid. My bottle of glue has formed a dry layer on top; can I still use it? Any glue that is still in liquid form is perfectly usable and reliable. If the dry layer is very thin, use a pointed tool to poke through it and carefully pull the dry layer through the cap. Do not microwave or heat your bottle of Gorilla Glue to soften the top layer. How do I clean up Gorilla Glue? Wipe off excess glue immediately with a dry cloth or standard paint thinner. Do not drag glue over material; instead, make small swipes to remove wet adhesive. Make sure you avoid skin contact. Cured glue can be removed with a chisel, scraper or sandpaper What is the proper clamp time? When using Original Gorilla Glue, clamp objects for 1–2 hours. For best results, leave overnight. What if I don’t have clamps? Gorilla Glue expands as it cures. To ensure the strongest bond, clamping pressure is needed. There are many different ways to clamp the surfaces, but keep in mind the stronger the pressure, the better the bond will be. Professional clamps are ideal, but if those aren’t handy, you can use heavy weight from bricks, books or even Gorilla Tape. The key is to ensure a tight-fitting glue line by applying even distribution of pressure. How much Gorilla Glue should I apply? Apply a thin layer of glue. A little bit goes a long way. As a general guide, use a ½ ounce per square foot. Be careful of uncured “squeeze-out” or wet glue, particularly on finished furniture. If you need to remove any squeeze-out, we recommend wiping with a dry cloth or using a standard paint thinner. Make sure you use the solvent with care in a well-ventilated area. Always wear gloves. Once the glue is dry, it is best removed mechanically: Try sanding, chiseling, scraping or picking. The dried glue will not damage tools. Visit our Gorilla Glue Directions page for more information. Why do I need to add moisture before gluing with Gorilla Glue? Gorilla Glue is moisture activated—this is what causes the chemical reaction in polyurethane adhesives. Therefore, you need to apply a small amount of moisture to one surface. Then apply glue to the dry surface and clamp. For dense hardwoods, lightly dampen both surfaces prior to gluing. Do I need to prepare the surface first? Make sure surfaces are clean and tight fitting. For smooth, shiny surfaces, such as metal and plastic, adhesion can be increased by sanding or abrading the surface. This gives Gorilla Glue more surface area to grip. Is Gorilla Glue really for the Toughest Jobs on Planet Earth? Gorilla Glue is an all-purpose adhesive. If used correctly, it will bond just about anything and for just about forever. It is free of solvents and fillers, which makes it strong and versatile. There are some surfaces and materials that are difficult to glue, such as certain plastics. Aside from a few of these materials, we are certain Gorilla Glue offers an extraordinary, waterproof bond on just about anything.
$17.12
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$139.40
A water-based, penetrating sealer that maintains the natural surface appearance while offering superior stain resistance against both oil and water-based stains. It is ideal for indoor and outdoor use with excellent UV resistance, suitable for a variety of surfaces. Key Benefits: Superior stain resistance (oil and water) Easy to clean and maintain Excellent UV resistance, ideal for outdoor areas Surface Preparation: Ensure surfaces are free from dust, dirt, grease, oil, previous coatings, adhesives, and other contaminants. Any stains or surface irregularities present at the time of application will be locked into the final finish. Test sealer on a small, inconspicuous area to ensure suitability. Application: Apply sealer by brush, roller, or low-volume spray applicator. Avoid excess application. Remove any material that hasn’t penetrated after 10 minutes with a cloth. Most surfaces require two coats, but porous surfaces may need additional coats. Allow 30 minutes drying time between coats. Drying Time: 30 minutes to 1 hour between coats. 24 hours before light foot traffic. 3 days for rubber wheeled traffic. 7 days for full curing. Coverage: 1L covers approximately 20m² per coat, depending on surface porosity. Clean-Up: Clean all equipment immediately after use with warm water or a water/detergent solution. Shelf Life: 12 months when stored in an unopened container at 23°C. Precautions: While it repels immediate spills, the sealer’s stain resistance diminishes if spills are left unaddressed. This product is not a waterproofing solution and is not recommended for use around swimming pools. SafetyAvoid inhalation, and eye or skin contact. In case of contact, rinse thoroughly with water. Refer to the Safety Data Sheet (SDS) for full details.
$48.79
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$66.77
Bostik Seal it Kitchen & Bathroom Translucent: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Bostik Seal it Kitchen & Bathroom Light Grey: The All-In-One Solution for Wet Areas Product Overview A premium oxime-curing silicone sealant specifically formulated to resist mildew and mold in hot, humid environments. Key Features Neutral cure for versatile application Excellent for UV exposure and porous surfaces Resistant to mold and mildew ±25% joint movement capabilities WaterMark approved for quality assurance Low odour and UV resistant Safe on various materials including galvanized steel and concrete Where to Use This product is ideal for sealing in: Kitchens, bathrooms, toilets, and showers Basins and vanity units Glass partitions Ceramic tiles Vitreous enamel Most laminated surfaces Fibre glass Rimless sinks Instructions Apply on clean, dry surfaces for optimal results. Follow safety guidelines as stated on the product label.
$15.35
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safetytips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Refer to the Safety Data Sheet (SDS) for full details.Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$34.65
FrogTape Pro Grade Deck and Joist Flashing Tape is a linerless, black waterproofing tape made to shield the timber parts of a deck from moisture, supplied here as a 96mm wide x 15.2m roll. It suits deck joists, stair stringers, posts and ledger boards, adding a protective layer over the surfaces most exposed to water, and it is a practical choice for both builders and capable DIYers.About the formulaThe tape pairs a solventless acrylic adhesive (ShurGRIP) with a conformable black polyolefin film backing. The adhesive is made using a UV curing process, is free of volatile organic compounds (VOCs) and is designed not to react with common caulks and sealants. The film bends easily around edges, corners and other transitions, and the tape self-heals around nails, screws and other fasteners to keep a waterproof seal. It is self-wound, so there is no release liner to peel and dispose of, and no primer is needed.Where to use itOutdoors: the tops and sides of deck joists, stair stringers, posts and ledger boards in residential deck construction, where the tape helps keep water away from framing timber.Installation temperature: it can be applied in a wide range, from -18°C to 65°C, and once installed it is designed to keep performing from -40°C to 115°C. It is rated for all-weather performance, including cold and damp conditions, and has 12-month UV resistance while exposed.Suitable surfaces include pressure-treated timber, OSB, concrete and other common building materials. The adhesive is initially repositionable, so you can adjust placement before pressing it down firmly.How to use itMake sure the surface is clean, dry and free of grease, oil and other contaminants. Unroll the tape along the joist, stringer, post or ledger, position it, then press it down firmly so the adhesive makes full contact. Work the tape around edges and corners, and press it into the surface around fasteners. Wider widths wrap further down the sides of a joist, so choose the width that best matches your framing. The same tape is also made in 48mm, 152mm and 304mm widths.Important notesThe manufacturer states the tape meets the AAMA 711-22 flashing tape test protocol. The 12-month UV resistance applies to the tape while it is exposed, so cover it with your decking or cladding in good time. As with any building product, check that it suits your surface and method of application before starting a larger job.Specifications Brand FrogTape Product Pro Grade Deck and Joist Flashing Tape (FSW 058) Size 96mm x 15.2m roll (1 roll) Colour Black Thickness 0.33mm Backing Black polyolefin film Adhesive Solventless acrylic Liner None (self-wound) Application temperature -18°C to 65°C Service temperature after install -40°C to 115°C UV resistance 12 months Standard AAMA 711-22 Use Exterior, above ground deck framing SafetyUse with normal care and keep the roll away from heat and open flame. Wear gloves when handling the tape on site to protect your hands from sharp edges and fasteners. Keep out of reach of children and store the roll in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$75.76
Crommelin Silicone WP Plus is a neutral cure silicone sealant made for wet areas, and it doubles as a bond breaker in Crommelin liquid applied waterproofing systems. This white 300g cartridge suits kitchens, bathrooms, laundries and similar jobs. It stays permanently flexible once cured and contains a mould and mildew inhibitor, so it holds up well in damp, steamy spaces.About the formulaA one-part, neutral cure silicone, so there is no mixing. The neutral cure chemistry will not corrode concrete or zinc coated and galvanised steel. It has a sag resistant body that can be used in vertical and overhead joints. Once cured it resists weathering, UV and vibration, and it is suitable for contact with aluminium shower screens. It can be used as a bond breaking sealant at joints, junctions and corners under waterproofing membranes, or as a durable finishing sealant.Where to use itIndoors: around showers, bath tubs, sinks, laundry fixtures, sanitary ware and spas, plus bond breaking joints in wet area waterproofing.Outdoors: exterior finishing joints and roof and gutter sealing, where the sealant is exposed to weather.Suitable materials include glass, glazed tiles and ceramics, steel and aluminium (suitably prepared), concrete, render, brickwork and blockwork, natural stone, fibre cement sheet and plasterboard. Use it only on clean, sound surfaces.How to use itMake sure the joint is clean, dry and free of dust, grease, soap residue and loose material. Cut the nozzle to suit the joint size, load the cartridge into a caulking gun and apply a continuous bead, then tool it smooth. Where it is used as a bond breaker in a waterproofing system, apply it at all joints, junctions, angles and internal corners before the membrane goes on. Refer to the Crommelin technical data sheet for full application guidance.Important notesThe cured silicone is not paintable, and it should not be used on freshly painted surfaces. Do not use it where it will contact food or potable water. Avoid materials that bleed oils, plasticisers or solvents, because they can affect adhesion. Keep it away from the silver backing of mirrors, such as at mirror edges. It is not a fire rated sealant. Silicone needs moisture in the air to cure, so it will not cure in a sealed, moisture-free environment.Specifications Brand Crommelin Product Silicone WP Plus (Silicone & Bond Breaker) Pack 1 x 300g cartridge (300ml) Colour White Base Neutral cure silicone, one part Application Cartridge, via caulking gun Features Mould and mildew resistant, permanently flexible, UV and weather resistant, sag resistant Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses where sensible. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$16.71
Selleys Flexiseal Clear is a premium, crystal-clear multipurpose elastic joint sealant for DIYers and tradies who want a flexible, weather-tough seal that stays discreet. Supplied in a 290ml cartridge, it handles everyday sealing jobs indoors and out, and it can be applied to damp or wet surfaces without a primer.About the formulaBuilt on Selleys hybrid technology (a moisture-curing silyl-modified polymer), this sealant has a low modulus, non-slumping body that stays put in joints up to 20mm wide. It cures to a strong, elastic, waterproof seal that resists UV and weathering and keeps its clear finish. It is free from solvents and isocyanates, has a low odour, and meets Green Building Council of Australia low VOC limits for general purpose and architectural sealants. Once cured it can be painted with water-based paints.Where to use itIndoors: gaps and joints around windows, doors, skirtings, trims and fittings where a clear, flexible seal is wanted.Outdoors: vertical and horizontal joints in exterior cladding, around frames and between common building materials exposed to sun and rain.Suitable materials include concrete, timber, metals, cement sheeting, brick, plaster, ceramic tiles and glass, along with most other common building surfaces. Test first on painted surfaces and any unusual materials.How to use itClean the joint and remove dust, grease and other contaminants, and degrease metal surfaces. Cut the nozzle at an angle, slightly wider than the joint, and load the cartridge into a caulking gun. Use a suitable backing rod to control depth where needed. Gun the sealant into the joint and tool it off promptly so it makes good contact with both sides. Remove excess uncured sealant with a damp cloth. Paint with water-based paints once the surface has skinned or cured.Important notesNot suitable for polyethylene, polypropylene or Teflon (PTFE). Not intended for permanent water immersion. Application is best between 5°C and 35°C. Cure time depends on temperature, humidity and joint depth, so allow enough time before putting the joint under stress or exposing it to water.Specifications Brand Selleys Product Flexiseal Clear Multipurpose Sealant Pack 290ml cartridge Colour Clear Base Moisture-curing silyl-modified polymer (hybrid technology) Application Cartridge, via caulking gun Skin time About 45 minutes (23°C, 50% RH) Non-slump Joints up to 20mm wide Density Approx. 1.05 g/mL Application temperature 5°C to 35°C Service temperature -20°C to 70°C Paintable Yes, with water-based paints Use Interior and exterior SafetyUse with normal care: work in a well-ventilated area, avoid contact with eyes and skin, and wear gloves and safety glasses. Keep out of reach of children and store in a cool, dry place with the cartridge sealed. Refer to the Safety Data Sheet (SDS) for full details.
$23.03
Bondall Betta Tilecare Shower Sealer is a clear, penetrating sealer that helps waterproof unglazed tiles and grout in showers and other wet areas, supplied in a 500ml pack. It soaks into the surface rather than sitting on top, so it protects without leaving a slippery film. It is made in Australia by Bondall and suits DIYers who want a simple, invisible finish.About the formulaA transparent, penetrating sealer based on silane chemistry. It leaves an invisible water-repellent finish with a non-slip feel, and the cured surface resists standard household chemicals. The same product is also sold under the Bondall TileGuard Shower Sealer name.Where to use itIndoors: shower walls and floors, bathroom tiling and grout, and other wet areas where the tiles and grout are unglazed.Outdoors: not specifically promoted by the manufacturer for outdoor use, so check the label before using it outside.Suitable surfaces include most unglazed tiles and grout, such as terracotta, ceramic, marble and slate.How to use itRemove old silicone strips and soap build-up first. Clean off mould using a mould cleaner or bleach, then rinse thoroughly with water. Repair or patch any loose or missing grout. Let the area dry for about 12 to 24 hours before sealing, or 3 to 4 days if the surface is porous or has just been high-pressure washed. Test a small, inconspicuous spot first. Apply with a paint brush, roller or pump spray, working evenly and avoiding pooling or heavy over-application, especially on pitted surfaces. If the product runs, wipe it back with a clean, dry, low-lint cloth. The manufacturer lists a 15 minute recoat time and 24 hours for a full dry.Important notesNot suitable for glazed surfaces. It is not designed to waterproof a water-holding vessel, such as a pot used as a fish pond. Grout should be in sound condition, as the sealer will not cover hairline cracks. It does not fix structural or plumbing defects in a shower, so refer those to the appropriate trade. Treat stains, moss and mould before sealing. Reviewers have reported staining on painted tiles with related Bondall sealers, so always test first.Specifications Brand Bondall Product Betta Tilecare Shower Sealer (also sold as TileGuard Shower Sealer) Pack 500ml Colour Transparent Chemistry Silane Application Paint brush, roller or pump spray Recoat time 15 minutes Full dry 24 hours Coverage 1L covers 5 to 10 m2 Use Unglazed tiles and grout in wet areas Origin Australian made and owned SafetyUse in a well-ventilated area, and wear a suitable respirator if spraying. Wear gloves and eye protection. On skin, wash the area well with running water. For eye contact, flush with running water for several minutes and see a doctor. Refer to the Safety Data Sheet (SDS) for full details.
$27.14
Soudal Bathroom & Kitchen Neutral Cure Silicone in clear is a pure silicone sanitary sealant for wet areas, supplied as a 300ml cartridge for use in a standard caulking gun. It is built for the joints that take the most punishment around showers, baths, sinks and benchtops, giving a waterproof seal that stays flexible and resists mould and mildew.About the formulaA neutral cure, non-corrosive silicone made from pure silicone with no extenders. It contains fungicides to help the seal resist mould and mildew in demanding sanitary conditions. It is easy to apply and tool, has a longer working time for smoothing joints, and stays permanently elastic once cured. The cured seal is colourfast and UV resistant, with a low modulus and a joint movement capability of +/- 25%.Where to use itIndoors: joints around bathtubs, vanities, shower screens, sinks, basins and toilets, kitchen splashbacks and benchtop joints, and sealing around plumbing fixtures in kitchens, bathrooms and laundries.Outdoors: not specifically recommended by the manufacturer for this product. Check the manufacturer data sheet or choose a product made for exterior use.Suitable materials include glass, tiles, fibreglass, vitreous enamel and many other common building and sanitary surfaces. Test an inconspicuous area first on any surface you are unsure about.How to use itMake sure the joint is clean, dry and free of dust, grease, soap scum and old sealant. Cut the nozzle to suit the joint, load the cartridge into a caulking gun and apply a steady, continuous bead. Smooth the bead with a profiling tool or a soapy water solution before the surface skins over, then remove any masking tape. Wipe away uncured excess promptly. Once cured, silicone has to be cut or scraped away.Important notesCure time depends on temperature, humidity and bead thickness, so allow plenty of time before exposing the joint to water. Keep joints well ventilated while curing. Always follow the manufacturer's instructions and test compatibility on sensitive materials before sealing.Specifications Brand Soudal Product Bathroom & Kitchen Neutral Cure Silicone Pack 300ml cartridge Colour Clear Base 100% silicone, neutral cure, no extenders Application Cartridge, via caulking gun Movement capability +/- 25% Key features Mould resistant, waterproof, non-corrosive, colourfast and UV resistant Use Bathrooms, kitchens and other wet areas SafetyWash exposed skin thoroughly after handling and wear suitable gloves and eye protection. Store locked up and dispose of contents and container in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$10.38
CAgroup Consolidated Alloys Butyl Double Sided Tape is a black, double sided butyl rubber tape for joining, sealing and waterproofing, supplied here as a single 48mm x 15m roll. The soft butyl adhesive moulds into rough and textured surfaces, so it suits builders, roofers and trades who need to seal overlaps and fix lightweight items where a smooth, hard-edged tape would struggle.About the formulaThe tape uses a highly water-resistant butyl rubber adhesive coated onto a polyethylene net. The net carrier gives the tape dimensional stability so it holds its shape in the roll and during handling. A siliconised kraft paper release liner protects the adhesive until you are ready to use it. Because the adhesive is soft and conformable, it follows uneven surfaces and also helps absorb vibration.Where to use itConstruction and civil work: fixing and sealing joints for waterproofing, and joining and sealing membranes.Ventilation and insulation: holding and sealing sisalation, as used in the HVAC industry.Signage and audio: mounting lightweight signage to textured surfaces, and isolating vibration in audio parts.The manufacturer data does not provide a full list of compatible surfaces, so test the tape on a small area of your own substrate before committing to a large job, especially on low energy plastics, oily or powdery surfaces.How to use itMake sure the surfaces are clean, dry and free of dust, oil and grease. Cut the tape to length, peel back the release liner progressively and press the tape firmly into place so the adhesive makes full contact with the surface. Bring the second surface or membrane into position and apply firm, even pressure along the whole joint to help the soft adhesive conform to the texture.Important notesThis is a lightweight mounting and sealing tape, so it is not intended for heavy structural loads. The manufacturer has not published set times or temperature limits for this size, so none are listed here. Check the supplier's technical data sheet if your application is critical, such as exposure to extreme heat or constant heavy movement. Store the roll with the liner in place until needed.Specifications Brand CAgroup Building Solutions Manufacturer Consolidated Alloys Product Butyl 48mm 15m Double Sided Tape Pack 1 roll Size 48mm wide x 15m long Colour Black Adhesive Butyl rubber Carrier Polyethylene net Release liner Siliconised kraft paper Application Hand applied, peel and press Format Double sided tape SafetyAs general good practice, keep out of reach of children, wash hands after handling and avoid contact with eyes. Store in a cool, dry place away from direct heat. Refer to the Safety Data Sheet (SDS) for full details.
$24.19
One On One Heavy Duty Double Sided Sealing Tape from CAgroup (Consolidated Alloys) is a butyl rubber tape that sticks and seals in a single step, supplied here as a 48mm x 5m roll. It is aimed at builders, roofers and DIYers who need a tacky, water-resistant seal between building materials, membranes and sheeting without mixing, gunning or waiting for anything to cure.About the formulaThe tape is a highly water-resistant butyl rubber sealant supplied on a siliconised kraft paper release liner, which peels away cleanly so the tape is easy to handle and position. The soft butyl adhesive conforms to rough and textured surfaces, so it can follow uneven substrates and fill small surface irregularities as it is pressed into place. It is described by the manufacturer as suitable for joining, sealing, waterproofing and absorbing vibration.Where to use itIndoors: joining and sealing builders film, polythene sheeting and sisalation foil, and damping vibration or noise on audio parts and similar fittings.Outdoors: sealing joints for waterproofing in construction and joining and sealing membranes on building sites.Suitable materials include glass, metal, wood, rendered concrete and plastics, including both high and low energy surfaces. Always test a small area first on unfamiliar plastics or coated surfaces.How to use itMake sure the surfaces are clean, dry and free of dust, oil, grease and loose material. Measure and cut the tape to length, peel back the kraft liner as you go, and position the tape without stretching it. Press the tape down firmly along its full length, then bring the second surface or membrane into place and apply even pressure so the butyl makes full contact. If the substrate is very rough, press harder or work the tape in so it can conform to the texture.Important notesButyl tape is a soft, pressure-sensitive sealant, not a structural adhesive, so do not rely on it alone to carry heavy loads. Butyl rubber can be softened by some solvents, so keep it away from solvent-based products unless you have checked compatibility. The manufacturer has not supplied application temperature limits, service temperature range, thickness or standards compliance figures for this size, so none are stated here. If you need compliance with a specific standard or approval (for example for damp-proof courses), confirm it with CAgroup before use.Specifications Brand CAgroup (Consolidated Alloys) Product One On One Heavy Duty Double Sided Sealing Tape Size 48mm wide x 5m long roll Pack Single roll Base Butyl rubber Format Double sided tape with siliconised kraft paper release liner Application Hand applied, press into place Use Joining, sealing, waterproofing and vibration absorption SafetyAs general good practice, keep the tape away from heat and open flame, avoid prolonged skin contact with the adhesive, wash your hands after handling, and store the roll in a cool, dry place out of direct sunlight and away from children. Refer to the Safety Data Sheet (SDS) for full details.
$11.10
![Davco K10 Plus Waterproofing Membrane 20L [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/davco-k10-plus-waterproofing-membrane-20l-grey-2.jpg?v=1792411411&width=645)
Davco K10 Plus is a premixed, ready-to-use, water-based polyurethane waterproofing membrane for tradies and builders, supplied here as a 20L pail in grey. It is a Class III membrane designed to sit under tile, stone and other resilient finishes on both walls and floors, in domestic and commercial jobs.About the formulaA one-part, water-based polyurethane that goes on straight from the pail with no mixing. It is rated Class III under AS/NZS 4858 and is highly flexible, with elongation above 500%. The manufacturer also lists it as non-toxic, UV stable and suitable as an anti-fracture membrane. Because it is water-based and solvent-free, it suits confined areas. Published technical figures include a Shore A hardness of 72 and a tensile strength of 2.1MPa.Where to use itIndoors: walls and floors in showers, bathrooms and other wet areas, ahead of tiling.Outdoors: terraces, balconies, roofs and walkways that will be covered with a hard finish such as tile.Suitable substrates include concrete, cement render and screeds, lightweight blocks, building boards approved for wet areas (such as compressed fibre cement sheet) and prepared metal surfaces. Metal needs an etching primer. All substrates should be primed with a suitable Sika primer before the membrane goes on.How to use itPrepare the substrate so it is sound, clean and primed. New render or screed needs a wood float finish and should cure before you start. Where falls are not already in place, form them with a sand and cement screed first. Apply the membrane by brush or roller in a minimum of two coats to reach a 1mm dry film. Each coat should go on at a wet film thickness of at least 0.75mm. Let the first coat dry for about 1 to 2 hours, then apply the second coat at 90 degrees to the first. Add further coats if needed to reach the minimum dry film thickness. Tools can be cleaned with water while the product is still wet. Tile over the cured membrane using a Sika polymer-modified cement-based tile adhesive.Important notesAllow about 6 to 8 hours before tiling or applying other finishes. Allow 3 days before flood testing and 5 days before the area returns to service. Drying times vary with temperature, humidity and film thickness. The membrane is not designed to be left exposed, so it must be covered with a finish. Follow the current Sika data sheet for primer selection, bond breakers, corners and joints, and for any movement joints. Wet area waterproofing must be done to the relevant Australian Standards and building code requirements, so use a licensed applicator where required. Shelf life is 12 months from manufacture. Store in a cool, dry place out of direct sunlight and do not let it freeze.Specifications Brand Davco (Sika) Product K10 Plus Waterproofing Membrane Pack 20L pail Colour Grey Base Water-based polyurethane, one part, premixed Classification Class III (AS/NZS 4858) Application Brush or roller Elongation Greater than 500% Coverage Approx. 13.3m² per 20L pail at two coats (1mm dry film) Recoat time 1 to 2 hours Ready for tiling 6 to 8 hours Flood test After 3 days Return to service 5 days VOC content 62g/L Shelf life 12 months from manufacture Use Interior and exterior, under tile, stone and other resilient finishes SafetyEven so, wear gloves and eye protection during application and keep the area ventilated, especially in enclosed spaces. Keep out of reach of children, avoid contact with eyes and skin, and do not let uncured product enter drains or waterways. Store the pail sealed, cool and out of frost. Refer to the Safety Data Sheet (SDS) for full details.
$266.99
Bastion Bond Breaker Waterproofing Joint Band is a 100mm wide, 10m long rubber reinforcing band for the most critical parts of a wet area waterproofing system, such as wall to floor junctions. It acts as the bond breaker in a liquid membrane system, so the membrane can cope with movement between two different surfaces instead of tearing at the join.About the bandThe band is made from a specialised grade of rubber that gives a rupture resistant seal and allows for the movement expected between abutting surfaces. It wets easily into the coats of a liquid membrane, which helps reinforce the finished membrane by improving puncture resistance and tensile strength. Because the band itself does the bond breaking, it removes the need for a separate bond breaker sealant at the joint, and installation is quick and straightforward. When used as part of a bond breaker system, it supports the requirements of AS 3740 (Waterproofing of domestic wet areas).Where to use itIndoors: wall to floor junctions in bathrooms, showers and laundries, and other critical joints in a wet area waterproofing system.Outdoors: Bastion's technical documentation lists the band as a bond breaker option within its membrane systems, but check the band's technical data sheet and your membrane's requirements before using it on external areas.It is designed to be embedded into Bastion liquid waterproofing membranes. Check your membrane's data sheet to confirm compatibility with other brands.How to use itMeasure and cut the band to suit each wall to floor junction. Apply a first coat of membrane, extending about 150mm up the wall and onto the floor, then embed the band into the wet membrane. Make sure the edges of the band are fully wetted out and there are no air bubbles behind it. Where lengths of band meet, overlap them by at least 50mm. If prefabricated corners are not being used, cut and fold the bottom leg of the band at corners and make sure it is fully bonded with the membrane. Then complete the membrane coats as set out in the membrane's data sheet.Important notesAlways follow the technical data sheet for the specific Bastion membrane you are using, including coat numbers and drying times. Surfaces should be properly prepared before the first coat goes on. Waterproofing in wet areas should be installed to the relevant Australian Standards and local requirements. If you are unsure, use a licensed waterproofer.Specifications Brand Bastion Product Bond Breaker Waterproofing Joint Band Size 100mm wide x 10m roll Pack 1 roll Material Rubber band Application Embedded by hand into wet liquid waterproofing membrane Minimum overlap at joins 50mm Standard Used as a bond breaker system to meet AS 3740 Use Wall/floor junctions and other movement areas in wet area waterproofing SafetyAlways read it and follow the instructions for the membrane you use with the band. Wear suitable protection when handling and installing it with liquid membranes, and store the roll clean and dry. Refer to the Safety Data Sheet (SDS) for full details.
$25.27
Gripset Betta Damp Stop is a one-part waterproofing primer and protective coating that helps hold back rising damp and moisture vapour moving through concrete, masonry and other porous mineral surfaces, supplied here in a 1L size. It suits renovators, tradies and confident DIYers who need a straightforward damp barrier under floor finishes, membranes and adhesives without mixing two parts together.About the formulaDamp Stop is a single-component, moisture-curing liquid in a light yellow colour. Because there is nothing to mix, you avoid the wasted product and short pot life that come with two-part epoxy primers. It is solvent free and odourless, so it can be used in confined areas. Once it has dried, it can be overcoated with other paints, coatings and adhesives. It also works as a dust-binding treatment for aged cement floors and dusty screeds.Where to use itIndoors: sealing the inside faces of cellar and basement walls against moisture vapour and dampness, priming floors ahead of membranes or finishes, protecting timber flooring, carpet and vinyl from rising damp, and stabilising dusty or aged screeds before floor finishes go down.Outdoors: priming external floors before a membrane is applied, and sealing the inner face of underground walls against residual moisture. The manufacturer lists it as suitable for internal, external, underground and immersed applications, and for resisting negative hydrostatic pressure.Suitable surfaces include concrete, cement mortar, renders and screeds, concrete and clay bricks, dense concrete, self-levelling compounds, compressed fibre cement sheet, fibre reinforced concrete, timber floorboards and sanded timber, and Hebel or other aerated concrete. For very porous, absorbent surfaces, or for metal and other smooth, shiny surfaces, the manufacturer points to other products in its range.How to use itStart with a clean surface, free of dirt, residues and old coatings. The surface can be damp but must have no surface water. Stir the product lightly, then apply with a short nap roller or short bristle brush. Leave 3 to 6 hours between coats and put the second coat on in the opposite direction to the first. Wait at least 24 hours, and make sure the primer is completely dry, before applying finishing membranes, coatings or adhesives.For high-build repairs, the manufacturer says to mix dry fine sand with the resin at about 3 parts sand to 1 part resin. Use a spatula for areas deeper than 1mm and keep the build to no more than 3mm.While still wet, tools can be cleaned with ethanol, methylated spirits or alcohol-based cleaners. Once dry, it has to be removed mechanically.Important notesDo not use over wet surfaces. Do not leave Damp Stop exposed as a finished membrane or sealer, as it is a primer. Do not apply when the surface temperature is below 10°C or above 35°C. Because it cures with moisture, cool or dry conditions can slow drying. The quoted drying times are tack free in 2 to 4 hours and dry film (ready to overcoat) in 24 hours, based on 20°C and relative humidity above 60%.Specifications Brand Gripset Betta Product Damp Stop Waterproofing Primer Size 1L Colour Light yellow Type One-component, moisture-curing liquid primer Solvent content Solvent free, odourless Application Short nap roller or short bristle brush Coverage (vapour barrier primer) About 6 to 8 m² per litre Coverage (negative pressure / moisture) About 3 to 4 m² per litre Coverage (dusty screeds, aged concrete) About 6 m² per litre Recoat time 3 to 6 hours between coats Tack free 2 to 4 hours Dry film (ready to overcoat) 24 hours Application temperature 10°C to 35°C surface Use Interior, exterior, underground and immersed SafetyEven so, avoid contact with eyes and skin, wear gloves and eye protection while applying, and keep it out of reach of children. Store the container sealed, away from direct heat and frost. Dispose of leftover product and empty containers in line with local regulations. Refer to the Safety Data Sheet (SDS) for full details.
$75.79
Boston Silicone Self-Fusing Tape in black is a 3 metre roll of stretchy repair tape made for quick fixes on leaking pipes and hoses. It fuses to itself as you wrap it, so there is no glue involved. It forms a watertight and airtight wrap, which makes it a handy emergency item for the plumbing kit, the toolbox or the shed.About the formulaThis is a silicone tape with no adhesive coating. It bonds only to itself, which means it does not leave sticky residue and can be removed cleanly when the job is done. The tape stretches well beyond three times its length, and that stretch is what lets it pull tight around pipes, hoses and fittings. It is rated for a very wide temperature range, from -55°C to +260°C. The black colour hides dirt and grime and blends in with black fittings.Where to use itIndoors: temporary sealing of weeping pipes, hose joins and fittings around the laundry, bathroom, kitchen or workshop; adding a comfortable, slip-resistant grip to tool handles.Outdoors: emergency repairs on garden hoses and tubing, and general fast fixes around the home, garden or workshop.The tape is designed for wrapping around pipes, hoses, fittings and tool handles. It is a multipurpose repair tape, so it also suits many other small wrap-and-seal jobs.How to use itMake sure the area you are repairing is clean and free of dirt and grease. Peel back the end of the tape and begin wrapping straight over the leak. Stretch the tape as you wind it on and overlap each turn, extending past the damaged spot on both sides. Press the finished wrap firmly so the layers fuse into one continuous seal. To fit a tool grip, wrap the tape around the handle in the same way. Cut the tape to length with scissors or a knife.Important notesBoston positions this tape for emergency and quick repairs. If a pipe or hose is badly damaged, plan to replace the affected section. Because the tape fuses only to itself, it will not stick to a surface if simply laid flat, so always wrap it back over itself. Keep the unused roll in a cool, dry place out of direct sun. Please follow the instructions that come with the pack.Specifications Brand Boston Product Silicone Self-Fusing Tape Pack 1 roll, 3m length Colour Black Material Silicone Application Hand wrapped, fuses to itself (no adhesive) Stretch Over 300% Temperature range -55°C to +260°C Use Pipe and hose leak repair, tool grips SafetyAs a general precaution, keep the tape out of reach of small children. Do not rely on it as a permanent fix for pressurised or safety-critical plumbing. Refer to the Safety Data Sheet (SDS) for full details.
$22.56
Sikalastic-1K (also labelled Sikalastic-1 Komponent) is a one-component, cement-based waterproofing membrane for wet areas, balconies, tanks and below-ground walls, supplied here in a 10kg pail that suits small to medium jobs. You only add water, then apply it by brush or trowel to form a flexible, crack-bridging, fibre-reinforced coating that protects concrete and prepares surfaces for tiling.About the formulaA fibre-reinforced mortar based on cement modified with alkali-resistant polymers, plus selected aggregates, fine fillers and additives. The consistency can be adjusted with the amount of water, so it can be made thinner for brushing or stiffer for troweling. It has good sag resistance on vertical surfaces, bonds well to concrete, cement mortars, stone and masonry, and can be applied on damp substrates. Sika lists it as meeting AS/NZS 4020 for products in contact with drinking water.Where to use itIndoors: bathrooms, showers and laundries before tiling with a cement-based tile adhesive; flexible protection of concrete tanks, basins and pipes; waterproofing walls and floors in basements against negative water pressure.Outdoors: terraces and balconies before tiling; swimming pools before tiling; external wall surfaces that will be backfilled in ground; protective coating for reinforced concrete exposed to freeze-thaw and carbon dioxide attack.Suitable substrates include concrete, cement mortars, stone and masonry. Substrates must be structurally sound and clean, and all joints and gaps must be sealed before coating.How to use itPrepare the substrate so it is sound and free of dust, oil and loose material, and seal any joints or gaps. Add water to the powder and mix with a low-speed mixer until smooth. For a 10kg pail, Sika's current data sheet gives about 3.0 litres of water for brush application and about 2.2 litres for trowel application. Apply in at least two layers: no more than about 1mm per layer by brush or 2mm per layer by trowel. Sika specifies a total dry film thickness of about 2mm for standard applications and 3 to 4mm for negative-pressure or immersed applications. When brushing, work in two directions, crosswise. Mixed material has a pot life of about 30 minutes at 20°C. Clean tools with water before the material sets; hardened mortar can only be removed mechanically.Important notesApply only when air and substrate temperatures are between 5°C and 35°C. The membrane must be completely hardened before tiling, overcoating or water contact. At 20°C, Sika's guide is about 2 days before tiling, painting with a water-based coating or immersion in water, and longer in cooler conditions (about 3 to 7 days at 10°C depending on the use). Allow about 15 days before contact with drinking water. Tile over it with a polymer-modified, cement-based tile adhesive from the Sika range. Times vary with temperature and humidity. Consumption depends on substrate roughness; as a guide, about 1.2kg per m² per mm of thickness. Store in the original sealed pail in cool, dry conditions and protect from water. Check the production date, as the current Sika data sheet gives a shelf life of 6 months. Always follow the current Sika product data sheet for your application.Specifications Brand Sika Product Sikalastic-1K (Sikalastic-1 Komponent) one-component cementitious waterproofing mortar Pack 10kg pail Colour Light grey Base Cement modified with alkali-resistant polymers, with fibres Application Brush or trowel (mix with water) Pot life About 30 minutes at 20°C Application temperature 5°C to 35°C (air and substrate) Fresh mortar density About 1.5 kg/L Consumption About 1.2 kg/m² per mm (guide) Water contact About 2 days at 20°C before immersion; about 15 days before drinking water contact Approvals AS/NZS 4020 (contact with drinking water) Use Interior and exterior SafetyWet and dry cement products can cause serious eye damage, so wear safety glasses or a face shield, protective gloves and long sleeves, and avoid breathing dust when handling and mixing. For skin contact, remove contaminated clothing and wash with soap and water. Keep out of reach of children, and do not eat, drink or smoke while using it. Refer to the Safety Data Sheet (SDS) for full details.
$137.46
The Fix-It-Fast Roof Repair Kit for Metal Roofs & Gutters is a ready-to-go patch kit for stopping leaks in metal roofing and gutters, with everything needed for the repair packed together in one tube. It pairs a self-adhesive Smartform flashing patch with a brush-on Wet Shield compound, so a homeowner can seal a leak in roughly five minutes without specialist tools or a tradie callout.About the formulaThe kit is a three-part system: a 300mm x 300mm Smartform patch, a 125g tub of Fix-It-Fast Wet Shield and an application brush. Smartform is an ultra-thin, flexible flashing with an aluminium surface and a butyl backing, and it can stretch by up to 60% so it can follow corrugated and irregular metal profiles. Wet Shield is a resin-based, fibre-reinforced, solvent-based repair compound. It is brushed around the edges of the patch to help stop water tracking underneath and lifting it. It can be applied to wet or damp surfaces, bridges small cracks, dries to a flexible membrane that resists algae and fungal growth, and needs no primer on sound, non-porous surfaces.Where to use itIndoors: not intended for interior use.Outdoors: patching leaks, splits and failed joins in metal roof sheeting (including corrugated and Colorbond profiles), gutters and valleys, and sealing around damaged flashing. It suits both residential and commercial maintenance jobs.Designed mainly for metal roofing and gutters. For tiled roofs, Fix-It-Fast makes a separate Tile Roof kit with a reinforced Dakaflash patch.How to use itClear loose debris, dirt, moss and algae from the repair area so the surface is sound and clean. Position the self-adhesive Smartform patch over the leak and press it down firmly so it conforms to the roof profile. Then brush Wet Shield around all the edges of the patch, overlapping onto the surrounding roof, to seal the perimeter and protect it from uplift. Once the Wet Shield has fully cured, it can be painted with an outdoor water-based acrylic paint if you want the repair to blend in. Keep the tub closed when not in use and follow the instructions supplied in the pack.Important notesA patch repair cannot fix a roof that is structurally unsound or unstable, so secure loose sheets and fixings first. The kit is built for localised repairs; for larger areas, Fix-It-Fast also sells flashing in longer lengths and Wet Shield in larger tins. Cure and recoat times are not confirmed here, so check the pack instructions. Wet Shield is solvent-based, so apply it in a well-ventilated outdoor area and keep it away from ignition sources.Specifications Brand Fix-It-Fast Product Roof Repair Kit for Metal Roofs & Gutters Pack 1 kit (patch, Wet Shield tub, brush) Patch Smartform flashing, 300mm x 300mm Patch stretch Up to 60% Wet Shield 125g tub Wet Shield base Resin-based, fibre-reinforced, solvent-based Application Self-adhesive patch plus brush-applied Wet Shield Pack dimensions Approx. 72mm x 72mm x 320mm tube Use Outdoor, residential and commercial SafetyThe Wet Shield in this kit is classified as a flammable liquid (Category 3) that may cause drowsiness or dizziness and is harmful to aquatic life with long-lasting effects. Keep it away from heat, sparks, open flames and other ignition sources, and do not smoke while using it. Avoid breathing the vapours and wear protective clothing and eye and face protection. Do not eat, drink or smoke while using it, and wash hands after use. Refer to the Safety Data Sheet (SDS) for full details.
$44.59
The Deks Rapid Flash Self-Adhesive Repair Strip is a lead-free, black flashing strip made for quick, temporary fixes to leaking roofs and gutters, supplied as a single 140mm x 500mm strip. It is a handy item to keep on hand when you need to stop a leak from a cracked tile or a damaged gutter until a permanent repair can be done.About the formulaThe strip is made from a rubber-based polymer with an integrated aluminium mesh. It has a fully adhesive base, so it goes on without separate sealants or fixings. The black finish suits most roof colours and materials. Deks lists the strip as suitable for all roof and gutter profiles and for most roof and gutter materials. It is lead-free, and you can cut it to size with heavy-duty scissors.Where to use itIndoors: not intended for interior use.Outdoors: temporary repairs to leaking gutters, cracked roof tiles and other roof leaks on a range of roof profiles and materials.Suitable materials include metal roofing and gutters, tile roofs and fibreglass sheeting. Deks describes the strip as suiting most roof and gutter materials, so test a small area first on unusual or heavily weathered surfaces.How to use itClean the repair area and let it dry fully, removing dirt, dust, loose debris and flaking material. Measure the area to be covered and cut the strip to length with heavy-duty scissors. Remove the backing from the adhesive face, position the strip over the leak and press it down firmly, working it into the roof or gutter profile so the adhesive bonds across the whole contact area. Always follow any instructions that come with the pack.Important notesThis is designed as a quick, temporary repair, so plan a permanent fix when conditions allow. Surface preparation matters, because the adhesive needs a clean, dry surface to grip. Take care when working at height, and be careful with cut edges of the aluminium mesh.Specifications Brand Deks Product Rapid Flash Self-Adhesive Repair Strip Pack 1 strip Size 140mm wide x 500mm long Thickness 2.3mm Colour Black Material Rubber-based polymer with integrated aluminium mesh Application Hand applied, self-adhesive backing, cut to size with heavy-duty scissors Lead content Lead-free Listed certifications AS 1530.8.1 (as listed by Deks), AS/NZS 2904, ASTM D7238, ASTM G154, BAL 19, BBA Use Exterior roof and gutter repairs (temporary) SafetyWear gloves when cutting and handling the strip, and watch for sharp mesh edges. Store the strip flat or rolled in a cool, dry place out of direct sun until you need it. Refer to the Safety Data Sheet (SDS) for full details.
$24.22
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in white is a ready-to-spray rubberised coating for sealing leaks and cracks around the home, supplied here as a single 340g aerosol can. It lays down a firm but flexible, watertight layer that helps keep out water, air and moisture, and it also protects the coated surface from rust. It suits quick repairs on gutters, roofing, flashing and ductwork without mixing, brushing or special tools.About the formulaA solvent-borne, hydrocarbon resin coating that sprays on and builds up to fill small gaps and cracks (the manufacturer lists gaps and cracks up to 6.35mm). It dries to a semi-smooth, firm finish that stays flexible and is designed not to sag or drip, so it holds its shape on sloped and vertical surfaces. Once cured it can be top-coated with latex or oil-based paints, which makes it easy to blend repairs into the surrounding colour scheme.Where to use itIndoors: sealing cracks and leaks in ductwork, pipework surrounds and other protected areas, with good ventilation while you spray.Outdoors: patching gutters, flashing, metal roofing, downpipes, masonry and concrete surfaces that need a flexible waterproof barrier.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Do a small test spray first if you are unsure about a surface.How to use it Prepare the surface by washing it with a detergent and water solution, rinsing well and letting it dry fully. Lightly sand glossy surfaces and wipe off the dust. Mask off nearby areas to protect against overspray. Spray outdoors or in a well-ventilated space, ideally when the temperature is between 10 and 32 degrees Celsius and humidity is below 65%. Avoid very windy or dusty conditions, and allow more drying time in cooler weather. Shake the can vigorously for about one minute once the mixing ball starts to rattle, and shake it often while you work. Do a test spray on cardboard to get a feel for the spray pattern, then hold the can 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a second heavier coat for full coverage. Moving the can closer builds a thicker film. Some foaming or bubbling at first is normal and settles as the coating dries. After use, turn the can upside down and press the nozzle until only clear propellant sprays out. If the valve clogs, remove the spray tip and rinse it in mineral turpentine. Never push an object into the valve opening. Clean wet or dry coating with mineral turpentine or xylene. Important notesNot recommended for rubber surfaces or for surfaces that sit in continuous water immersion. Under the manufacturer's data, touch dry is about 2 hours at 21 to 27 degrees Celsius and 50% humidity, further coats can go on after 15 to 30 minutes, and you should allow 24 hours for a full cure and before top-coating. Cooler or more humid conditions will slow drying. This is not a fire or high-heat resistant coating. Shelf life is listed as 5 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour White Base Solvent-borne, hydrocarbon resin Application Aerosol spray Gap and crack fill Up to 6.35mm Touch dry About 2 hours (21 to 27°C, 50% RH) Recoat 15 to 30 minutes Handle 2 to 3 hours Full cure / topcoat 24 hours Practical coverage About 0.37 to 0.46 m² per can at a thick 125 micron film, or about 0.74 to 0.93 m² per can at 62.5 microns (manufacturer figures allowing for 15% material loss) Paintable Yes, with latex or oil-based paints Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. Contents are under pressure, so do not pierce or burn the can, even when empty. Use only outdoors or in a well-ventilated area, and avoid breathing the spray, mist or vapour. Refer to the Safety Data Sheet (SDS) for full details.
$23.95
Rust-Oleum LeakSeal Flexible Rubber Coating Spray in Black is a ready-to-use aerosol sealer for stopping leaks and sealing cracks around the home, workshop and site, supplied here as a single 340g can. It sprays on as a rubberised coating that builds a flexible, water-tight barrier over a wide range of common building surfaces, which makes it a quick fix for hard-to-reach or awkward spots where a caulking gun is difficult to use.About the formulaA solvent-based, hydrocarbon resin rubber coating that sprays on as a high-build film. It dries to a firm, semi-smooth black finish that stays flexible and is formulated not to sag or drip. The cured coating helps block moisture and protects against rust and corrosion, and it can be top-coated with acrylic (latex) or oil-based paints once cured.Where to use itIndoors: ductwork, pipes, air conditioner drip pans, vents and other protected areas where a flexible waterproof seal is needed (use only with good ventilation).Outdoors: gutters, downpipes, roof sheeting, flashing, skylight surrounds, metal sheds and buildings, and concrete or masonry surfaces where cracks or small holes let water in.Suitable surfaces include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Always do a small test spray on an inconspicuous area first, particularly on plastics.How to use itPrepare the surface so it is clean, dry and free of loose material, dirt, grease and flaking paint. Do a test spray on a piece of cardboard first to get a feel for the spray pattern, then apply the coating over the leak or crack using even passes, following the directions on the can. Additional coats can be applied after 15 to 30 minutes if a heavier build is needed. Once cured, the surface can be top-coated with acrylic or oil-based paint. Use outdoors or in a well-ventilated area.Important notesThe coating is touch dry in about 2 hours, can be recoated with itself after 15 to 30 minutes, and can be top-coated after 24 hours (times based on roughly 21 to 27°C and 50% relative humidity, so allow longer in cool or humid conditions). It is not intended for surfaces under continuous water immersion. It is not rated as fire or high-heat resistant, and it is not a mould or mildew-resistant coating. Coverage depends on the film thickness applied: about 0.74 square metres per can at a thin film (62.5 microns) or about 0.37 square metres per can at a thicker film (125 microns), allowing for typical material loss. Shelf life is around 2 to 3 years.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 340g aerosol can Colour Black Finish Semi-smooth, firm, flexible Base Solvent-based, hydrocarbon resin Application Aerosol spray Touch dry About 2 hours Recoat (with itself) 15 to 30 minutes Top-coat with paint After 24 hours Full cure About 24 hours Coverage per can About 0.74 m² at 62.5 micron, or 0.37 m² at 125 micron Paintable Yes, acrylic (latex) or oil-based paints Use Interior and exterior SafetyUse only outdoors or in a well-ventilated area, keep away from heat, sparks, flame and other ignition sources, and wear protective gloves, protective clothing, and eye and face protection. Store the can away from heat and do not store above 49°C. Refer to the Safety Data Sheet (SDS) for full details.
$27.92
Rust-Oleum LeakSeal Clear is a rubberised spray-on sealant that stops leaks and seals cracks in one easy aerosol, supplied here as a single 312g can. It lays down a flexible, water-tight coating over gutters, roofing, flashings, ducting and more, and the clear finish lets the original surface show through. It suits homeowners and maintenance tradies who need a quick, no-fuss repair.About the formulaA solvent-based, rubberised coating built on a hydrocarbon resin, delivered by a flammable propellant. It sprays on as a firm but flexible film that fills small gaps, cracks and holes (the manufacturer rates it for gaps up to about 6mm) and forms a barrier against water, air and moisture. It dries to a semi-smooth finish that does not sag or drip, helps protect the surface from rust, and can be topcoated with latex or oil-based paint once cured.Where to use itIndoors: ductwork, vents, pipes and other surfaces that need a flexible moisture seal.Outdoors: gutters, downpipes, roof flashings, metal roofing, sheds, vents and cracked masonry or concrete.Suitable materials include metal, aluminium, galvanised metal, PVC, concrete, masonry, asphalt roofing materials, vinyl siding and fibreglass. Test a small hidden area first on any surface you are unsure about.How to use itRemove all dirt and debris from the repair area. The manufacturer's technical data also advises washing with detergent and water, rinsing and letting the surface dry thoroughly, removing loose paint or old coatings, and lightly sanding glossy surfaces. Mask off surrounding areas to protect them from overspray.Apply outdoors or in a well-ventilated space, ideally between 10 and 32°C with humidity below 65%. Avoid very windy or dusty conditions.Shake the can vigorously for one minute after the mixing ball starts to rattle, and shake often during use. Do a test spray on cardboard to get a feel for the pattern.Hold the can about 20 to 45cm from the surface and spray in short, even strokes. Apply a light first coat, then a heavier second coat for full coverage. Moving closer to the surface builds a thicker film.Once the coating has fully cured, it can be painted with latex or oil-based paint if you want it to match the surroundings.Important notesDry to touch in about 30 minutes, with full cure in about 24 hours. Not recommended for rubber surfaces or for surfaces under continuous water immersion. It is not fire or high-heat resistant and is not rated as mould or mildew resistant. Coverage varies with surface porosity and how thick you apply it. Do not apply to hot surfaces.Specifications Brand Rust-Oleum Product LeakSeal Flexible Rubber Coating Spray Pack 1 x 312g aerosol can Colour Clear Base Solvent-based, hydrocarbon resin Application Aerosol spray Dry to touch About 30 minutes Full cure About 24 hours Maximum gap or crack size Up to about 6mm Application temperature 10 to 32°C Paintable Yes, with latex or oil-based paint Flexibility Remains flexible Use Interior and exterior SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Do not spray onto a flame. The can is pressurised: do not pierce or burn it, even when empty, and do not expose it to temperatures above 50°C. Use outdoors or with good cross-ventilation. Refer to the Safety Data Sheet (SDS) for full details.
$23.25
![Rust-Oleum LeakSeal Self-Fusing Silicone Tape 25.4mm x 3.04m [Clear] (2)](http://gluesaustralia.com.au/cdn/shop/files/rust-oleum-leakseal-self-fusing-silicone-tape-25-4mm-x-3-04m-clear-2.png?v=1792411058&width=645)
Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a no-adhesive repair tape for stopping leaks on pipes and hoses and for wrapping damaged wiring insulation, supplied here as a clear 25.4mm x 3.04m roll. It stretches and wraps around awkward shapes, then fuses to itself to form a tight, water-resistant seal that suits quick home fixes as well as automotive and workshop repairs.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. That is why it peels away cleanly later without leaving a sticky residue. The manufacturer rates it excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention, and good for flame, abrasion, tear and solvent resistance. It is also rated good to fair for acid and oil resistance. It meets UL 510 and is claimed to insulate up to 8,000 volts.Where to use itIndoors: weeping or leaking pipes and joints, hoses on appliances, and frayed or worn cable insulation (see the electrical safety note below).Outdoors: garden and irrigation hoses, exposed pipework, and vehicle or equipment hoses and fittings exposed to sun and weather.Suited to wrapping around pipes, hoses, fittings and cables made from common materials such as metal and rubber. As the tape fuses to itself rather than relying on adhesion, it conforms to irregular shapes well. Test a small area first on delicate surfaces.How to use itDry the area to be repaired first. Hold the end of the tape firmly on the problem spot, then stretch the tape under tension as you wrap it around the object. Overlap each layer by about 13mm and keep wrapping so the tape lies over itself and fuses. Cover the whole problem area, cut the tape when finished and press the end down firmly. To remove it, simply unwrap or cut it off.Important notesThe tape needs to be stretched while wrapping, with each turn overlapping the last, to fuse properly. Loose or single-layer wraps will not seal. Treat it as an effective repair or emergency fix, and replace damaged pipes, hoses or cables where a permanent solution is needed. The manufacturer lists continuous operating temperatures from -45°C to 200°C and intermittent exposure from -65°C to 260°C, so keep it away from conditions above these limits. Do not rely on it to repair mains-voltage wiring: isolate the power first and have electrical work carried out by a licensed electrician. Avoid contact with strong oxidising agents, strong acids and strong alkalis.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Size 25.4mm x 3.04m roll (1 roll) Colour Clear Material Self-fusing silicone rubber tape Application Hand wrapped under tension, no adhesive or tools Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (+/- 5) after 24 hours Electrical insulation Up to 8,000 volts (manufacturer claim) Standard Meets UL 510 Use Interior and exterior SafetyWash your hands thoroughly with soap and water before eating, drinking or smoking after handling. If it gets in the eyes, rinse with water and remove contact lenses if present and easy to do. If heated to decomposition, silicone can give off acrid smoke and irritating fumes, so avoid excess heat and ensure good ventilation. Store the roll in a cool, dry place away from strong oxidisers, acids and alkalis. Refer to the Safety Data Sheet (SDS) for full details.
$20.12
Rust-Oleum LeakSeal Self-Fusing Silicone Tape is a stretch-and-wrap repair tape for stopping leaks on pipes and hoses and for insulating damaged electrical wires, supplied here as a single black 25.4mm x 3.04m roll. It has no adhesive layer. Instead, each wrap fuses to the layer beneath it, so it forms a tight, sealed sleeve around the repair and can be cut off later without leaving sticky residue behind.About the formulaThis is a silicone rubber tape that bonds to itself rather than to the surface underneath. Rust-Oleum describes it as a moisture and chemical resistant barrier that also helps protect against corrosion. Its technical data sheet rates it Excellent for moisture resistance, electrical insulation, UV and ozone resistance and corrosion prevention. It rates solvent, abrasion and tear resistance as Good. Acid, oil and hydrocarbon resistance is rated Good to Fair. The tape has a minimum tensile strength of 700 psi, a minimum elongation of 300% and a Shore A hardness of 55 (plus or minus 5) once cured for 24 hours. It meets UL 510. Rust-Oleum states it insulates up to 8,000 volts.Where to use itIndoors: temporary or emergency repairs on leaking pipes, fittings and hoses, and insulating or protecting frayed electrical wires and cable joins.Outdoors: wrapping hoses, fittings and exposed connections that face moisture and sunlight, including automotive and general workshop repairs.Because it fuses to itself, it works best on pipes, hoses, cables and other tubular or irregular shapes that you can wrap fully around.How to use itDry the surface before you start. Press the end of the tape onto the problem area, hold it firmly, then stretch the tape with tension as you wrap it around the object. Overlap each layer by about 13mm (the manufacturer gives 1.2 to 1.4cm) and wrap the tape over itself so it fuses. Cover the whole problem area, cut the tape and press the end firmly into place. To remove, cut the tape carefully with scissors or a knife.Important notesThe tape fuses to itself, so wrap it all the way around the item with each layer overlapping the last. The 700 psi figure on the TDS is a tensile strength rating, so do not treat it as a working pressure rating for pipes. Keep pressurised, hot or critical repairs in line with the system's own requirements and replace them with a proper repair where needed. The TDS gives a continuous operating range of -45°C to 200°C and an intermittent range of -65°C to 260°C. Flame resistance is rated Good, so do not treat the tape as fireproof. For electrical repairs, make sure the circuit is isolated and have any permanent work done by a licensed electrician.Specifications Brand Rust-Oleum Product LeakSeal Self-Fusing Silicone Tape Model number 279241 Size 25.4mm wide x 3.04m long roll (single roll) Colour Black Base Self-fusing silicone rubber Application Hand applied, stretch and wrap Continuous operating temperature -45°C to 200°C Intermittent operating temperature -65°C to 260°C Tensile strength 700 psi minimum Elongation 300% minimum Hardness Shore A 55 (plus or minus 5), cured 24 hours Electrical insulation Up to 8,000 volts (manufacturer rating) Standard Meets UL 510 Use Interior and exterior SafetyIf it gets in your eyes, flush with plenty of water for at least 15 minutes, keep the eyelids open, remove contact lenses if easy to do and keep rinsing. Keep out of reach of children and store in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$22.71
Sika MultiSeal BT is a self-adhesive butyl sealing tape with an aluminium top surface, supplied here as a 10 m x 100 mm roll in grey for sealing and repairing roofs, gutters, flashings and other building elements. The high tack butyl adhesive grips a wide range of building materials, indoors and outdoors, so you can seal a joint or patch a leak without mixing, gunning or waiting for anything to cure.About the formulaThe tape is built on a flexible butyl rubber compound with a reinforced aluminium film on top. The aluminium face gives the tape its UV resistance. The butyl layer underneath is self-adhesive and is protected by a release liner until you are ready to stick it down. Sika describes it as having good adhesion at low temperatures, very good weather and UV resistance, and very good heat stability with no flow or oil migration. The aluminium face can be overpainted with most conventional paint systems, but test the paint first to confirm compatibility.Where to use itIndoors: sealing and insulating ductwork for ventilation and air conditioning, dampening and insulation work, and sealing joints on modular buildings and office containers.Outdoors: repairing and sealing sheet metal roofs and flashings, facade elements, concrete roof tiles, metal and PVC gutters and downpipes, chimneys and skylights, and caravans and containers.Suitable materials include metal sheeting, glass, timber, PVC and concrete, along with most other common building materials. Check the compatibility of the butyl adhesive with the surface first, particularly on plastics and painted surfaces.How to use itSurfaces must be sound, clean and dry. Sika recommends cleaning and pre-treating the substrate with Sika Aktivator-205 applied with a clean towel. Cut the tape to length, peel back the release liner and press the tape firmly onto the surface, working along its full length so it makes good contact. Follow the current Sika product data sheet for application temperature limits, joint overlaps and any other installation details.Important notesThis tape is not for use on natural stone. It is not a replacement for an adhesive or mechanical fixing, so do not use it for permanent fixing or in load-bearing applications. On porous surfaces, water can travel in underneath the tape. Test paint compatibility before overpainting.Specifications Brand Sika Product MultiSeal BT High Tack Elastomeric Butyl Sealing Tape Size 10 m roll x 100 mm wide Colour Grey Base Butyl rubber compound Top surface Aluminium foil Bottom surface Self-adhesive butyl with release liner Thickness 1.0 mm including film Service temperature -30 °C to +80 °C Application Cut to length and press on by hand Shelf life 36 months from date of production Use Interior and exterior SafetyFollow the storage and handling advice on the pack and in the data sheet. Keep the roll in its original packaging until needed. Refer to the Safety Data Sheet (SDS) for full details.
$57.09
![Selleys Flexiseal FC Polyurethane Sealant & Adhesive 600ml Sausage [White] (2)](http://gluesaustralia.com.au/cdn/shop/files/selleys-flexiseal-fc-polyurethane-sealant-adhesive-600ml-sausage-white-2.png?v=1792410682&width=645)
Selleys Flexiseal FC is a fast-curing polyurethane sealant and adhesive in white, supplied here as a 600ml sausage for sealing and bonding jobs around the building site or the house. It does two jobs in one product: it seals joints between common building materials and bonds them, and it stays flexible enough to cope with the movement those joints see through the seasons.About the formulaA single-component polyurethane with a non-slumping body, so it stays put in vertical joints instead of sagging. It is designed to grip common building surfaces without a primer, cures to a waterproof, flexible seal and can be painted once cured. Selleys rates it for joint movement of around plus or minus 25%.Where to use itIndoors: joints between wall and ceiling elements, around door and window frames, and acoustic rated walls, plus general bonding of building materials.Outdoors: weatherproofing joints between brickwork, masonry, concrete, timber or metal frames, sealing around roofing, retaining walls, external wall and cladding joints, and expansion joints.Suitable materials include concrete, brick, masonry, ceramic tile, metals, softwood and hardwood, plus some plastics (test other plastics and rubber first).How to use itMake sure the joint is clean, dry and free of dust, oil and other contaminants, and use a backing rod in deeper joints. Cut the end of the sausage, load it into a sausage-style applicator gun and extrude the sealant so it makes full contact with both sides of the joint, avoiding trapped air. Tool the surface smooth with a spatula before a skin forms. Once cured, it can be painted. For outdoor work, a suitable exterior paint will help the finish last longer.Important notesWill not adhere to polyethylene (PE), polypropylene (PP) or PTFE. Do not apply when the air or surface temperature is below 5°C. Not suitable for permanent water immersion or below water line use. Not intended for structural applications or general glazing. Avoid alcohol and solvent cleaners on the sealant while it cures, as they can interfere with the cure. Very damp substrates can cause bubbling in the sealant. It may affect the drying of oil or alkyd based paints, so test paint compatibility first. White sealant can yellow slightly with age and sun exposure. Store unopened sausages below 30°C in a cool, dry place out of direct sunlight, where they keep for around 12 months from manufacture. Opened sausages may skin over near the opening, so discard any lump or skin before using the rest.Specifications Brand Selleys Product Flexiseal FC Polyurethane Sealant & Adhesive Size 600ml sausage Colour White Base Polyurethane (single component) Application Sausage, via sausage gun Joint movement capability Plus or minus 25% Minimum application temperature 5°C Shelf life (unopened) About 12 months below 30°C Use Interior and exterior SafetyPolyurethane products can still irritate the skin, eyes and airways, so wear gloves and safety glasses, work with good ventilation and avoid prolonged skin contact. Store in a cool, dry, well-ventilated place away from heat, ignition sources and food, upright and tightly closed. Keep out of reach of children. Refer to the Safety Data Sheet (SDS) for full details.
$32.06
The Uni-Pro 100mm Waterproofing Brush is a trade-quality brush built for putting down waterproofing membranes and other thick protective coatings, and it suits bathrooms, laundries and other wet areas. It pairs tapered synthetic filaments with a stainless steel ferrule and a solvent resistant handle, so it can cope with coatings that would wreck an ordinary paint brush.About the brushThe tapered filaments are designed to hold up against harsh coatings, including acetone-based products. They are also shaped to pick up and release a good load of coating, which helps you get an even application. The head is a synthetic, solvent resistant filament. The ferrule is stainless steel for long life, and the handle is composite plastic. The 100mm head gives you good coverage on floors and walls.Where to use itIndoors: waterproofing bathroom floors and walls, laundries and other wet areas, including primer, membrane and reinforcing coat applications.Outdoors: suitable for applying compatible coatings where the coating manufacturer approves exterior use.Suitable for use with most waterproofing membranes, shellac based sealers, sealers and primers, bonding agents, bitumen coatings and liquid reinforcing coatings. Always check the coating manufacturer's data sheet to confirm the brush is appropriate for the product you are applying.How to use itPrepare the surface and mix the coating as directed by its manufacturer. Load the brush and work the coating into corners, edges and junctions, then lay it off evenly across the surface. Follow the coating manufacturer's instructions for coat thickness, number of coats and recoat times. Clean the brush straight after use with the clean up method recommended for the coating you applied.Important notesThis is a brush only and does not include any coating, primer or reinforcing tape. Choose the cleaning method to suit the coating you used, and do not let coating cure in the filaments. A 75mm size is also available in the Uni-Pro range for tighter spots.Specifications Brand Uni-Pro Product Waterproofing Brush Size 100mm Pack Single brush Colour Green Model number UWM100 Brush head Synthetic tapered filament, solvent resistant Ferrule Stainless steel Handle Composite plastic Approx. product size 290mm long x 100mm wide x 25mm deep Application Hand applied brush SafetyTake extra care with solvent-based coatings, which can be flammable. Store the brush clean and dry. Refer to the Safety Data Sheet (SDS) for full details.
$17.90
Bondall Betta Tilecare Wet Area Waterproofer is a fast-curing, water-based liquid rubber membrane for sealing wet areas beneath tiles and renders, supplied here in a 10L pail for bigger bathroom, laundry and balcony jobs. It dries to a flexible, elastic film that acts as a water and vapour barrier, and it is designed to cope with permanently wet conditions, including ponding water once cured.About the formulaA water-based, one-part elastomeric membrane that is described by the manufacturer as non-toxic and non-flammable. It is classed as a Class III membrane under AS/NZS 4858 and, when used with the Betta detailing range, is designed to meet the Australian wet area requirements including AS 3740. The fast-curing formulation lets you tile or render over it quickly, and it is compatible with a range of tile adhesives, renders and toppings. No primer is needed on plasterboard or sound, dry concrete.Where to use itIndoors: bathroom and laundry floors and walls, shower recesses and other tiled wet areas, plus under screeds and toppings.Outdoors: balconies, decks, podiums and terrace floors, planters and retaining walls, and roofs that will be covered with screeds or toppings.Suitable substrates include concrete, screeds, renders, brick, plasterboard, fibre cement sheet and marine plywood. It sits under ceramic, porcelain, granite, marble and other stone tile finishes. Other surfaces, such as smooth, dense or damp ones, may need a Betta primer first, so check the technical data sheet for your substrate.How to use itMake sure the surface is sound, stable, clean and free of dust, oil, grease and loose material. Install the bond breaker and elastic joint band detailing first, as this is part of meeting AS 3740. Apply by brush, roller or spray unit in a minimum of two coats, changing direction between coats, to a total minimum coverage of 1.5 litres per square metre. This builds a dried film of roughly 1.2mm. Vertical or pitched areas can be done at around 1 litre per square metre. Take the membrane up walls at least 150mm in general wet areas and to 1.8m in shower recesses, finishing with a continuous, seamless film. Clean tools with water straight after use.Important notesTypical drying times at normal conditions (about 20°C, 50% humidity): tack free in about 45 minutes, recoat in about 1 hour, and ready to tile or topping over in about 4 hours. Retailer information quotes 6 hours before tiling, so allow the longer time in cool or humid weather and always follow the pack. Allow ample cure time before flood testing, as Bondall publishes more than one figure for this. Finish toppings must be water-based and solvent-free. Areas with rising damp or negative pressure should first be treated with Betta Damp Stop. Use on concrete slabs with hydrostatic or vapour pressure from below is outside the scope of the independent appraisal. Do not apply when rain is imminent. Always check the technical data sheet for your project.Specifications Brand Bondall (Betta Tilecare) Product Wet Area Waterproofer Pack 10L pail Base Water-based liquid rubber (elastomeric) Application Brush, roller or spray unit Coverage Minimum 1.5L per m2 over two coats (about 6.6 m2 per 10L pail) Dried film thickness Approx. 1.2mm Tack free About 45 minutes Recoat About 1 hour Tile or topping over About 4 to 6 hours (see notes) Standard AS/NZS 4858 Class III membrane Clean up Water Use Residential and commercial wet areas, interior and covered exterior SafetyEven so, wear gloves and eye protection, ensure good ventilation, and avoid contact with skin and eyes. Keep out of reach of children. Store in a sealed container in a cool place and protect from frost. Refer to the Safety Data Sheet (SDS) for full details.
$212.26
Mandala Art Mosaic Grout Sealer & Waterproof Additive is a 1L acrylic-based liquid made for mosaic artists and hobbyists who want to strengthen, seal and waterproof their grout with a single product. It can be mixed into grout powder or brushed over finished work, which makes it handy for outdoor pieces such as birdbaths and pavers.About the formulaAn acrylic-based white liquid that adds strength and flexibility to grout. Used correctly, it gives the grout water resistance, helps reduce mould growth and deepens the grout colour. It leaves a slight sheen on the finished surface.Where to use itIndoors: mosaic artworks, craft projects and decorative pieces where you want stronger, sealed grout lines.Outdoors: birdbaths, outdoor pavers and garden mosaics that will be exposed to moisture.It can also be used as a surface sealer on wood and MDF, and on porous surfaces such as terracotta and ceramic.How to use itFor a waterproof grout, use the additive in place of the water when you mix your grout powder, then stir to a smooth, toothpaste-like consistency and apply as normal. For extra strength and durability, you can brush a final coat of the additive over the project once the grout has dried. As a surface sealer, brush it onto the clean, dry surface. Check the product label for mixing and drying details, as the correct method matters for good results.Important notesThe manufacturer does not recommend this product for large works such as swimming pools. Water resistance and waterproofing depend on correct use. Use as directed on the label, and do a small test on a spare piece first if you are unsure about a surface. Specific mixing ratios, drying times and coverage have not been confirmed here, so please follow the pack instructions.Specifications Brand Mandala Art Product Mosaic Grout Sealer & Waterproof Additive Model GSA Size 1L bottle Colour White liquid Base Acrylic Application Mixed into grout powder in place of water, or brushed on as a sealer Finish Slight sheen, enhances grout colour Use Indoor and outdoor mosaics SafetyAvoid contact with eyes and prolonged skin contact, use in a well-ventilated area, and wash hands and tools after use. If it gets in the eyes, rinse with plenty of water. Keep out of reach of children and store the container sealed in a cool, dry place. Refer to the Safety Data Sheet (SDS) for full details.
$30.29
The Crommelin Flexible Membrane Reinforcing Internal Corner is a pre-formed 90° corner piece that strengthens the most vulnerable junctions in a liquid applied waterproofing system, supplied here as a single piece. It is made to be embedded in wet Crommelin brush or roller applied membrane. It gives wall to wall and wall to floor corners a flexible, seamless waterproof detail without cutting and folding fabric on site.About the productThe corner is built from rot proof TPE rubber and polyester fabric. It is designed to accommodate structural movement in joint areas where cracking and splitting often start. It is highly durable and tear resistant, and it suits quick, straightforward installation. The manufacturer states it is suitable for use with membranes approved to AS 3740, AS 4858 and the Australian Building Code. It is part of the Crommelin Flexible Membrane Reinforcing & Bond Breaking range, which also includes an external corner, a pipe and tap sleeve and bond breaking tape.Where to use itIndoors: showers and bathrooms, laundries and kitchens, wherever a wet area membrane meets an internal corner.Outdoors: balconies and roofs, podiums and decks, retaining walls, planter boxes, tanks and ponds, when used with a suitable Crommelin liquid applied membrane.This corner is intended for use with Crommelin liquid applied waterproofing membranes applied by brush or roller. Choose the right Crommelin membrane for your project and substrate.How to use itPrepare the surface and prime it as directed for the membrane you are using, then let the primer dry. Brush a generous coat of membrane over the corner area, at a minimum wet film thickness of 0.6mm. Cover enough area to match the entire back of the corner piece, and make the coat thick enough for good adhesion. Do not let the membrane skin or dry before the corner goes in. Press the corner into the wet membrane. Work over all edges with a brush so they are fully embedded and no creases or air pockets remain. Then brush more membrane over the top surface so the corner is completely wet embedded. If the corner you are waterproofing is not exactly 90°, snip about 20mm along each of the three fold lines with scissors before installing. This helps the corner sit flush. Once all corners are in, treat the remaining wall to wall and wall to floor joints as directed in the Crommelin technical data sheet, then complete the membrane coats as directed.Important notesDrying times of the waterproofing membrane may be longer where reinforcing is used. If the corner is still visible after the membrane is applied, add further coats to reach the right film build. Always follow the application, recoat and tile-over instructions for the specific membrane you are using. Check that the membrane is compatible with this corner before you start.Specifications Brand Crommelin Product Flexible Membrane Reinforcing Internal Corner 90° Model number 1787-001 Pack 1 x internal corner piece Material TPE rubber with polyester fabric Approx. size 140mm x 140mm x 60mm Application Wet embedded into brush or roller applied Crommelin liquid membrane Standards For use with membranes approved to AS 3740, AS 4858 and the Australian Building Code Use Interior wet areas and exterior waterproofed areas SafetyWear gloves when handling it and when working with the liquid membrane. Store the corners flat in a cool, dry place away from direct sun. Refer to the Safety Data Sheet (SDS) for full details.
$10.37
Fix-It-Fast Repair Tape is an aluminium-faced butyl flashing tape for quick, dependable waterproofing and leak repairs, supplied here as a wide 150mm x 5m roll. It suits DIYers and roofing or building trades who want a simple, self-adhesive way to seal flashings, gutters and damaged roof areas without mixing, heating or special tools.About the tapeThe tape pairs an aluminium top layer with a self-adhesive butyl backing protected by a release liner. This construction is designed for waterproofing and vapour sealing, and it is formulated to bond to virtually all non-porous building materials. The aluminium face is UV resistant, and the product is promoted for its excellent age resistance. The 150mm width covers larger repair areas in fewer passes than the narrower rolls in the range.Where to use itIndoors: vapour sealing and general waterproofing tasks on non-porous building materials where the tape will not be exposed to the weather.Outdoors: flashing repairs, gutters, downpipes, cracked or damaged roofing, metal roof sheeting, sheds, skylights, caravans and boats.Suitable materials include metal (including Colorbond), PVC, polycarbonate, fibreglass, timber and smooth masonry, provided the surface is clean, dry and free of dust and oils.How to use itClean the surface thoroughly and make sure it is dry. Cut the tape to the length you need and peel away the release liner. Press the tape down firmly, working from the centre outwards to push out air pockets, then press the edges down so they are fully sealed. For best results, apply when the temperature is above 5°C.Important notesAdhesion is best on clean, dry, non-porous surfaces. If an area is wet, dry it as much as you can before applying the tape. Rough, dusty, oily or porous surfaces can reduce adhesion, so prepare them properly first. The manufacturer indicates the tape remains stable in service from about -40°C to 90°C. Check the repaired area from time to time to make sure the seal is holding.Specifications Brand Fix-It-Fast Product Repair Tape, Aluminium Reinforced Butyl Flashing Tape Size 150mm wide x 5m long (1 roll) Colour Aluminium (silver) Construction Aluminium top layer with self-adhesive butyl backing Application Hand applied, peel and stick Service temperature -40°C to 90°C (manufacturer FAQ) Best application temperature Above 5°C Use Interior and exterior SafetyKeep it away from young children, and wear gloves when handling the aluminium edges if you are cutting it. Store the roll in a cool, dry place out of direct sun. Refer to the Safety Data Sheet (SDS) for full details.
$44.47
![Fastfix Wet Shield One Coat Instant Waterproofing 2.5kg [Grey] (2)](http://gluesaustralia.com.au/cdn/shop/files/fastfix-wet-shield-one-coat-instant-waterproofing-2-5kg-grey-2.jpg?v=1792410637&width=645)
Fastfix Wet Shield is a fibre-reinforced, one-coat roof and gutter repair membrane that can be applied straight onto wet or damp surfaces, supplied here in a 2.5kg tin in grey. It is made for emergency leak repairs, so you can seal a leaking roof without waiting for the rain to stop, and it also suits planned maintenance work in dry weather.About the formulaA resin-based, solvent-based compound with reinforcing fibres that interlace to bridge small gaps and cracks. The manufacturer describes it as formulated from lightfast acrylic polymers, which helps it withstand UV exposure for longer than traditional bitumen coatings. It is waterproof the moment it goes on, so rain straight after application will not wash it off. It cures to a smooth, seamless, flexible membrane that resists algae and fungal growth. On sound, non-porous surfaces no primer is needed.Where to use itIndoors: not recommended for internal use.Outdoors: roofing and gutter repairs, including tile and metal roofs, valleys, gutters, flashings, fascias, downpipes and cappings, plus concrete and brickwork. Areas that collect ponding water are covered by the one-coat system, provided the recommended minimum finished fall is achieved.Suitable materials include concrete, fibre cement, roof tiles, slate, metal roofing, guttering, brickwork, lead flashing, uPVC, asphalt and bituminous roof coatings. Non-ferrous metals such as aluminium, copper and previously painted non-ferrous metals should be primed with a suitable etch primer first. If you are unsure about a surface, run a small adhesion test before committing to the whole job.How to use itEmergency wet repairs: no preparation is needed. Brush a thick coat over the affected area to create an immediate barrier against water ingress.Planned dry-weather work: clear moss, lichen and debris by brushing, scraping or pressure washing. Let the surface dry, remove any oil or grease with white spirit, and let it dry again. Then apply the product generously with a brush, roller or squeegee in one coat.Seal air-conditioning vents for at least 24 hours during and after application. Clean tools with white spirit or methylated spirits.Important notes Not recommended for wooden surfaces, tanking, fishponds or internal use. Not designed for areas with heavy foot traffic. Allow up to 6 to 7 days to dry, depending on temperature and coat thickness. It may stay soft for longer in some climates, which does not affect its waterproofing. Manufacturer information recommends applying between 5°C and 25°C and a minimum finished fall of 1:80. Discolouration may occur over new asphalt, tar or bitumen. Shelf life is up to 2 years in an unopened container stored correctly. If a primer is needed on a particular substrate, check with the manufacturer for suitable options. Specifications Brand Fastfix Product Wet Shield One Coat Instant Waterproofing Pack 2.5kg tin Colour Grey Base Resin based, fibre reinforced, solvent based Application Brush, roller or squeegee, one coat Coverage 1kg to 2kg per m2, depending on substrate Drying time Up to 6 to 7 days, depending on temperature and thickness Application temperature 5°C to 25°C Minimum finished fall 1:80 Flash point 40°C (per SDS) Clean up White spirit or methylated spirits Use Exterior roofing and gutters SafetyKeep away from heat, sparks, open flames and other ignition sources, and do not smoke. Avoid breathing vapours, use in a well-ventilated area, and wear protective clothing, eye protection and face protection. For eye contact, rinse with plenty of water for 15 minutes holding the eyelids open. For skin contact, wash with soap and water. Refer to the Safety Data Sheet (SDS) for full details.
$89.91
You have seen 144 out of 277 products
Keep water out of joints, seams and enclosures with waterproof and weatherproof products. Match cure type and flexibility to the application (bathroom, kitchen, outdoor). Use the filters to narrow by material, chemistry, cure speed, temperature rating, and clean‑up. Always check the product page and TDS/SDS for suitability and instructions.
