GorillaWeld is an incredibly strong, heavy duty two-part adhesive. The tough, steel bond epoxy formula has a 4250 PSI bond strength and sets in just 10 minutes. GorillaWeld is waterproof and versatile, creating a long-lasting, permanent bond to metal, plastics*, concrete, ceramics, PVC, fibreglass and more! Features: INCREDIBLY STRONG: 4250 PSI STEEL BOND EPOXY SETS IN 10 MINUTES WATERPROOF** FORMS PERMANENT BOND DRIES DARK GRAY EASY TO USE BONDS: Metal, Plastic*, Concrete, PVC, Fiberglass, Ceramic & More! *Not recommended for use on polyethylene or polypropylene plastics. **Bonded wood materials should not be submerged or soaked in water. Directions All surfaces should be clean and free of debris. To improve adhesion, roughen smooth surfaces with sandpaper before gluing. Remove cap from each tube and use top of cap to puncture foil seal. Dispense equal parts from each tube onto a clean, disposable surface. Mix with disposable mixing tool for approximately 20 seconds until the colour is uniform. Apply mixture to surface within 3 minutes. Clamp surfaces together and leave undisturbed for 10 to 30 minutes. Full cure in 24 hours. Cure time dependent on temperature, humidity and quantity applied. *Note: Not recommended for use on polyethylene, polypropylene or similar plastics. Specs: APPLICATION TEMPERATURE: 32°F to 90°F SERVICE TEMPERATURE: -40°F to 300°F SET TIME: 10 minutes CURE MECHANISM: 2 Part Reaction, requires mixing OUTDOOR: Yes FREEZE/THAW STABLE: Yes WATERPROOF: Yes* PAINTABLE: Yes SANDABLE: Yes DRILLABLE: Yes SHAPEABLE: Yes STAINABLE: No CHEMICAL RESISTANT: Limited EXPANDS WHEN CURED: No SHRINKS WHEN CURED: No CURED COLOR: Dark grey GAP FILLING: Yes *Not suggested to use on wood materials submerged or soaked in water Will GorillaWeld bond plastic/vinyl/rubber? Gorilla Weld will work well on many types of plastic; however, we do not recommend for use on polypropylene (PP), polyethylene (PE) or similar plastics, or any type of rubber with high oil or plasticizer content. What does GorillaWeld work best for? GorillaWeld is ideal for metal and plastic (see above) substrates. GorillaWeld does not sag so it is ideal for vertical surfaces How should GorillaWeld be stored? GorillaWeld should be stored in a cool, dry place. Store away from children and animals. How do I mix GorillaWeld? GorillaWeld should be mixed 1:1 for 20 seconds or until uniform prior to application. Does GorillaWeld become hot during cure? Yes, mixing the hardener and resin together creates an exothermic reaction and will generate heat during cure. Consideration should be taken on mixing vessel as not to melt. How long do I have before GorillaWeld begins to harden? GorillaWeld will begin to harden after 3 minutes. Adhesive should be applied prior. What surfaces will GorillaWeld bond to? GorillaWeld is particularly suited for metal, plastic and other rigid surface bonding. Is GorillaWeld Food Safe? GorillaWeld is not recommended for direct or indirect food contact and should not be considered food safe. Why is GorillaWeld odour so strong? GorillaWeld is based on methyl methacrylate chemistry which has a naturally strong odour. We suggest using in a well-ventilated area. How do I remove GorillaWeld from body/skin? Uncured: GorillaWeld can be harmful through skin absorption and it is strongly recommended that you wear gloves during use. If GorillaWeld is on the skin, try removing with a dry cloth or paper towel and then wash the area thoroughly with soap and water. Cured: Cured material can be rolled off the skin. Remove as much cured material as possible and wash the area thoroughly with soap and water. For medical emergencies, call 1-800-420-7186 anytime How do I remove GorillaWeld from my surface? Uncured: Wipe up as much material as possible with a dry cloth and clean any remaining product/residue with Isopropyl alcohol (IPA) or acetone following solvent manufacturer’s instructions. Cured: For removing cured/dried GorillaWeld, mechanical means such as sanding or chiselling. What should I do if I think a human or animal has ingested GorillaWeld? For medical emergencies, call 1-800-420-7186 anytime
$15.82
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. PRODUCT FEATURES CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More APPLICATION TEMPERATURE – 0°C to 37.8° C, best at room temperature SERVICE TEMPERATURE – -28.9° to 82.2° C OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – Minimal What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight fitting joints. It’s perfect for a fix you need done fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also minimally gap filling, which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant, and can withstand intermittent exposures, however is not meant for a constant soak. Original Gorilla Glue is 100% waterproof and can withstand soaking and longer term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$14.92
Gorilla Tough & Clear Mounting Tape is a clear double-sided tape that mounts in an instant, for a long-lasting, weatherproof bond. The crystal clear adhesive tape won’t yellow over time, Gorilla Tough & Clear Mounting Tape is perfect for indoor and outdoor projects and sticks to smooth and rough surfaces. Completing DIY projects is easy with this tough, double-sided tape. Mount, build, and repair for a perfect finish, every time. Features Weatherproof - For indoor and outdoor use. Crystal Clear Adhesive - Won't yellow over time. Double Sided Tape - coated with adhesive on both sides for easy hanging. Bonds - Plastic, Metal, Wood, Glass, Brick, Ceramic, Stone & More! *weight limits may vary depending on surface texture, porosity and flatness of surface. Both surfaces must be completely flat to make full contact with adhesive. Is Gorilla Mounting Tape permanent? Yes. Once Gorilla Mounting Tape is used to mount an object, it is meant to be held in place permanently, and not be removed. How do I remove Gorilla Mounting Tape’s liner? Once Gorilla Mounting Tape is pressed onto the surface of the object to be held, remove the liner by peeling it from a corner of the tape. This can be done by using a fingernail or similar object to separate the liner from the tape. How do I remove Gorilla Mounting Tape? Gorilla Mounting Tape is a permanent tape. Once applied, it can be difficult to remove, and can damage surfaces if the objects are pulled away from the surface. If Gorilla Mounting Tape isn’t exposed and cannot be reached by hand between the mounted object and the surface, a prying motion on the object from one corner can sometimes remove it from the surface. Please note that damage to the surface can occur. If Gorilla Mounting Tape is exposed and within reach between the mounted object and the surface, pull the tape parallel to the surface (or vertically downwards) to remove it from the object. How much Gorilla Mounting Tape should I use on my project? Use four inches of Gorilla Heavy Duty Mounting Tape per pound of weight being held.
$10.86
The strength and versatility you have come to expect from Gorilla Glue is now available in an easy to use, crystal clear, non-foaming formula. Clear Gorilla Glue is incredibly strong and is ideal for indoor and outdoor applications and bonds virtually everything. Features: CRYSTAL CLEAR NON-FOAMING WATER RESISTANT INCREDIBLY STRONG EASY TO USE BONDS VIRTUALLY EVERYTHING: Wood, Stone, Metal, Ceramic, Foam, Glass & More Directions All surfaces must be clean and tight fitting. Clear Gorilla Glue will stain clothes. 1. Damp It For non-porous surfaces only (i.e. metal, glass, plastics), lightly dampen one surface with water. Do not add water to the bottle. 2. Glue It Apply Clear Gorilla Glue to surfaces. Best at room temperature. 3. Clamp-It Clamp objects together for 2 hours. Full cure in 24 hrs. You can use heavy objects to achieve clamping pressure. *Not recommended for use on polyethylene or polypropylene plastics. Storage Tips After each use, wipe nozzle clean with a dry cloth and tightly replace lid. Store in a cool, dry place with exposure to light. Lack of light and heat can cause the product to yellow. Cured glue can be removed from work surface with chisel, scraper or sandpaper. Store away from children and animals. Specs: APPLICATION TEMPERATURE – 32° to 100° F, best at room temperature SERVICE TEMPERATURE – -20° to 180° F OUTDOOR – Yes MOISTURE RESISTANT – Water resistant – not recommended for continual water exposure PAINTABLE – Yes – Can be painted with oil-based and spray. acrylic/latex and stains require sanding SANDABLE – Yes STAINABLE – Yes – Will require sanding EXPANDS WHEN CURED – No CURED COLOR – Clear TECHNICAL STANDARDS – ANSI/HPVA Type II STORAGE TIPS – Store in a cool, dry location. Store with access to light, if possible. GAP FILLING – No FAQS What is the difference between Clear Gorilla Glue and Gorilla Super Glue? Gorilla Super Glue is designed to dry fast and works best with tight-fitting joints. It’s perfect for a fix you need doing fast. Clear Gorilla Glue offers an extended working time, which allows you to reposition your project. It is also gap filling which allows you to glue uneven surfaces. Is Clear Gorilla Glue waterproof? Clear Gorilla Glue is water resistant and can withstand intermittent exposures, however, is not meant for a constant soak. Original or White Gorilla Glue is 100% waterproof and can withstand soaking and longer-term water exposure, assuming the materials being are not significantly affected by the water. How do I maximize the shelf life of Clear Gorilla Glue? After use, wipe the nozzle with a dry cloth, close cap tightly and store at room temperature with access to light, if possible.
$12.90
Use for handy jobs around the office, house, garage
$1.50
Accurate measurements up to 0.02mm Outside, Inside and Depth measurement scale Metric The Craftright 150mm vernier caliper is perfect for your next precision measuring job, made from Carbon steel and measuring from 0 to 150mm. Precise metric measurements as low as 0.02mm can be obtained using the main scale for full numbers in combination with the vernier scale for accurate measurements between 0 to 1mm.
$11.74
Glue Dots® Repositionable Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for hanging lightweight items, securing rugs to hardwood and tile floors, and can be easily removed. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$8.73
Repositionable Dots™ Dot N Go® dispenser fits in the palm of your hand and can be used as a 'second set of hands' to hold small, lightweight items in place temporarily. It's perfect for quick fixes and repairs around the home. Not recommended for heavy or bulky materials that require a permanent bond. Glue Strength - Temporary Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$9.70
Advanced Strength Dots™ Dot N Go® fits in the palm of your hand and is perfect for quick fixes and repairs. With a small footprint, the Advanced Strength Dot N Go stores easily in a toolbox or drawer for easy access. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Hand-held Dispenser | Easy to Use Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free Adhesive Size: 3/8 in. diameter Adhesive Color: Amber Quantity: 125 Adhesives
$8.95
Glue Dots® Advanced Strength Double-Sided Sheets can be custom cut to any size or shape to provide adhesive coverage for projects both big and small. Ideal for tough jobs and DIY projects that require exceptional holding power. Not recommended for temporary applications or delicate items. Glue Strength - Super-Strength (Holds up to 8 lbs.) Features/Benefits: Resealable Bag | Easy to Store Acid-Free | Photo Safe Non-Toxic | Kid Friendly Instant Bond | Mess Free
$7.98
Craft Glue Dots® are versatile, permanent adhesives ideal for heavier materials like wood or metal, large embellishments or thick cardstock. Glue Strength - Super-Strength Features/Benefits: Hand-held Dispenser | Easy to Use Acid Free| Photo Safe Non Toxic | Kid Friendly Specifications Adhesive Size: 3/8 in. diameter Adhesive Color: Clear Quantity: 200 Adhesives
$12.74
FiberFix Rigid Patch is the other cousin of the Repair Wrap- a fibreglass patch for permanent repairs on flat or hard-to-wrap surfaces. Simply apply the patch over the hole and expose to sunlight or UV light (but don't expose before applying!). In 3-5 minutes after exposure, the patch will cure! What's Included?: One 3"x3" patch, One 2"x8" patch, One 5"x5" patch Cure Time: 5-10 minutes (depending on the amount of sunlight/UV exposure) What Surfaces Will It Work On?: Any rigid surface (will not work on flexible surfaces such as fabrics or highly bendable plastic) Sandable/Paintable?: Yes! Applications: Rain gutters, fences, garbage barrels, water tanks, boats, canoes, automotive body, and much more!
$34.50
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$42.00
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$35.00
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297_2a31a89b-b3a8-48c5-b47f-43439b0dbea3.png?v=1754715706&width=645)
![FiberFix Repair Wrap 100x Hardens like steel 5cm x 127cm [2 Rolls]](http://gluesaustralia.com.au/cdn/shop/files/857101004297.jpg?v=1754715706&width=645)
FiberFix Repair Wrap combines industrial-strength fiber and specialized resin into a wrap that hardens like steel and provides a permanent fix. Simply dip the wrap in water to activate the resin, wrap around what you need to fix, and 10 minutes later it is cured! Cure Time: 5-10 minutes (the warmer the water the faster the cure) Water Pressure Rating: Up to 60 PSI Temperature Rating: Between -30° F and 300° F Sandable & Paintable?: Yes! Applications: Water pipes, garden and shop tools, furniture frames, hoses, outdoor gear, camping equipment, sporting equipment...and much more!
$31.00
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$24.20
Elmer’s School Glue is a washable, no-run glue that is easy to use and stays where you put it. - It is safe, non-toxic and washable, so accidental messes mean easy clean-up! - Perfect for making slime - Colour: White - Pack size: 225ml How can I un-clog my glue cap and what’s the proper way to clean it? The glue caps can actually be taken apart to help remove any blockage. Simply open the cap as far as it will go and then pull the orange part straight up and it should "pop" off. This should allow you to easily access any blockage. The blockage can be cleared with something like a toothpick or paper clip. You can also soak these separated parts in room temperature water which should help to more easily free up any blockage. Once clear, the orange part can simply be pressed/snapped back into position. Watch the how-to un-clog a glue cap video for visual instructions. Is glue made from horses or other animals? No, Elmer's does not make glue from horses or use animals or animal parts. Elmer's products are made from synthetic materials and are not derived from processing horses, cows or any other animals. Why doesn't glue stick to inside of the bottle? As long as the glue remains inside the bottle away from air it will remain fluid. Glue hardens when there is a loss of water from the formula. Exposure to the atmosphere will cause the water to evaporate and make the glue harden. That's why it is important to keep the cap on the glue bottle closed to prevent hardening or drying out. I have a milk allergy. Are your products safe for me to use? Elmer's products are derived from synthetic materials, not any type of animal or milk protein. Of course, if you experience any kind of allergic reaction, be sure to check with your doctor regardless of the type of product you are using. How long can I keep glue? If stored properly and capped tightly, Elmer's school glues and wood glues have an average shelf life of 2 years. Krazy Glue, also known as a cyanoacrylate, has a shelf life of approximately 12 - 18 months. Is Elmer's glue gluten free? All of Elmer's products are gluten free except for the Elmer's Finger Paints. The finger paints contain wheat and oat products. Is Elmer's glue acid free? No. Most of Elmer's glues that are acid-free are labelled as such. Some of Elmer's most popular acid-free products include all of Elmer's glue stick, rubber cement and spray adhesive products.
$6.50
Safer for the environment and still does the work. The EcoConcepts Graffiti Remover is a revolutionary development in the ongoing struggle to remove paint, ink, permanent marker and unwanted graffiti from a variety of surfaces. Unlike traditional graffiti removers, EcoConcepts is environmentally-friendly and much safer for the user. Suitable for removing paint, pen, sticky residues, grease, oil, crayon, lipstick and more. Made from renewable ingredients and readily biodegradable. Contains no carcinogens, phosphates, chlorine bleach or harsh solvents. EcoConcepts represents truly green cleaning. Diluted with water it can be used on plastic, laminate, metal, carpet, most painted surfaces and whiteboards. Undiluted it will penetrate and remove graffiti from porous surfaces such as brick, stone or concrete. I’m a concentrate and nearly ready for use. Use undiluted for the toughest jobs on porous and durable surfaces. Dilute for use on less stubborn stains and less durable surfaces. Always test on an inconspicuous area first. UNDILUTED For ultimate paint and stain removal, especially on unpainted surfaces such as concrete. HIGH DILUTION Generally safe on less durable and painted surfaces – 1 part product to 5 parts water, e.g. 167mL of product makes 1L of high-dilution solution. LOW DILUTION For tougher jobs on relatively durable surfaces – 1 part product to 3 parts water, e.g. 250mL of product makes 1L of low-dilution solution.
$42.54
An effective and easy-to-use neutral cleaner designed to remove general household dirt, grime, and oils from tiles and grout. Ideal for daily use, this cleaner is powerful enough to tackle grease in kitchens and bathrooms while being gentle enough for regular application. Key Benefits: Powerful cleaner for tiles and grout Effectively removes grease in kitchens and bathrooms Regular use reduces mould and mildew growth Suitable for general-purpose surface cleaning Cost-effective when diluted and applied by spray Easy to use for everyday cleaning Use On: Tiles, grout, and general household surfaces Surface Type: Walls and floors Location: Indoor and outdoor use Colour & Sizes: Size: 1L Item Code: 22504 Coverage: Wipe On: Dilute 10ml per 1L of water Spray On: Dilute 6ml per 1L of water Directions for Use: Test First: Before the first application of Dunlop Tile & Grout Cleaner, test a small amount of product in an inconspicuous area to ensure the desired result. Dilution: Mix 10mL of Dunlop Tile & Grout Cleaner per 1L of water. For best results, use hot water. Application: For general cleaning, apply the cleaner using a mop. For stubborn dirt, use an appropriate scourer or scrubbing pad that won't scratch the tile surface. Keep your tiles and grout clean and fresh with this powerful, easy-to-use cleaner, perfect for daily household maintenance.
$25.02
DUNLOP®WALL TILE ADHESIVE is a ready-mixed indoor wall tile adhesive. Ideal for all types of ceramic wall tiles and dimensional stones such as marble and granite, it can be used on a number of surfaces which include compressed fibre-cement sheets, plasterboard, cement render and adequately prepared painted surfaces (oil-based paint only). DUNLOP®WALL TILE ADHESIVE has superior flexibility and high grab to support even the heaviest of wall tiles. SURFACE PREPARATION Surfaces must be consistently flat and firmly fixed. Clean off dust, oil, grease and all loose contaminating materials or coatings. Ensure surfaces are dry, with no residue or permanent dampness. Prime porous surfaces (e.g. fibre- cement sheets, cement render) with DUNLOP®PRIMER & ADDITIVE beforehand and allow to dry. Cement Render Allow to cure for at least 7 days. Render should have a wood float finish. Plasterboard There is no need to prime the cardboard surface. However, where sheets are joined, DUNLOP®PRIMER & ADDITIVE must be used over the base jointing compound. Do not use the topping compound in areas which are to be tiled. Compressed Fibre-Cement Sheets Remove surface dust with a damp sponge and prime with DUNLOP®PRIMER & ADDITIVE and allow to dry before tiling. Painted Surfaces Oil-based paint should be roughened mechanically and loose flaking paint should be removed. Ensure the paint is suitable for tiling over. Thoroughly remove water-based paints. Do not use paint stripper or solvents. Allow surface to dry after cleaning. MIXING No mixing required. APPLICATION As a general guide use a 6mm notch trowel to spread adhesive achieving a minimum 1mm bed thickness. Do not wet tiles before fixing. If backs of tiles are dusty clean with a damp sponge. Spread the adhesive with the notches running horizontally across the wall. Spread only one square metre at a time and ensure a skin has not developed on the adhesive before bedding tiles. Press and slide the tile into position ensuring the whole of the back of the tile is in good contact with the adhesive. Use tile spacers if desired to ensure even spacing. Remove any surplus adhesive on face of tile or between joints before it sets. Adjustment of tiles should be carried out within 60 minutes of laying (at 23°C and 50% humidity). COVERAGE DUNLOP®WALL TILE ADHESIVE will cover approximately 0.5m2per kg. Coverage will vary depending on the condition of the surface being tiled and application technique. DRYING TIME DUNLOP®WALL TILE ADHESIVE will dry in approximately 24 hours depending on ambient temperature, porosity of surface and tiles. MOVEMENT JOINTS Incorporate movement joints at 3.5m intervals and at internal corners. Any structural movement joints must be carried through to the face of the tiling, at junctions between different background material and at fixtures interrupting the tile surface. These joints should be about 6mm wide and and kept free from adhesive. They should be filled with a high quality flexible material e.g. DUNLOP®COLOURED SILICONE. GROUTING Wait until adhesive has set. This takes approximately 24 hours. Remove tile spacers and use DUNLOP®GROUT adding DUNLOP®PRIMER AND ADDITIVE to enhance colour, impart a degree of flexibility and reduce porosity and staining. For easier maintenance seal with DUNLOP®GROUT SEALER. CLEAN UP While it is still fresh, DUNLOP®WALL TILE ADHESIVE can be cleaned off with a damp sponge. Tools, hands and material soiled with adhesive can be easily cleaned with water as long as the adhesive is still fresh. CAUTION Do not use DUNLOP®WALL TILE ADHESIVE to fix green marble. Do not use DUNLOP®WALL TILE ADHESIVE in continuous immersion applications e.g. swimming pools, tanks etc.. Do not use DUNLOP®WALL TILE ADHESIVE over non- absorbent substrates and waterproofing membranes due to prolonged drying times. DUNLOP GUARANTEE Product is guaranteed for 10 years when installed to manufacturers instructions. Manufactured under a quality system certified as complying with ISO 9001 by an accredited certification body. Material Safety Data Sheets are available TECHNICAL DATA Characteristics of product: Colour: White Viscosity: 790 000 cps S.G: 1.47g/cm3 pH: 9.1 Form: Viscous paste Application Properties: (@23°C and 50% relative humidity) Open Time: 80 mins Adjustability Time: 60 mins Mechanical Properties: Fundamental Characteristics Shear adhesion strength: Shear adhesion strength after aging: 2.5 Mpa (AS 4992.1) Minimum requirements 1.0Mpa (D1) 3.5 Mpa 1.0Mpa (D1) SAFETY Keep out of the reach of children. If skin contact occurs wash skin thoroughly with running water. If swallowed, give a glass of water and contact Poisons Information Centre. In case of contact with eyes, rinse with plenty of water and contact a Doctor. MSDS available on request.
$66.83
Dunlop Premixed Resaflex Tile Adhesive Ready to use, flexible and tough ceramic tile adhesive for dependable indoor tiling. Ideal for interior walls and fibre-cement sheet residential floors. No mixing required, spreads smoothly, and delivers a secure bond when applied at the correct bed thickness. Key Benefits Ready mixed convenience for faster start and less mess Flexible bond that helps accommodate minor movement Non-slump paste with excellent grab on vertical surfaces Suitable for common interior wall substrates and fibre-cement sheet floors Where To Use Walls: Interior applications on cement render, plasterboard, and fibre-cement sheet Floors: Residential fibre-cement sheet floors Tiles: Ceramic and similar porous tiles Surface Preparation Surfaces must be flat, clean, dry and firmly fixed. Remove dust, oil, grease and loose materials. Prime porous surfaces like cement render and fibre-cement sheet, and any base jointing compound on plasterboard, then allow to dry. Remove water based paints completely. If paint integrity is uncertain, roughen or remove. Application Use an appropriate notched trowel: as a guide 6 mm for walls, 10 mm for floors. Spread only as much as you can tile within open time, typically about 1 m² at a time. Ensure no skin has formed. Bed tiles into a 1.5 mm to 6 mm adhesive layer. Press and slide to ensure full contact. Clean excess adhesive from tile faces and joints before it sets. Coverage Guide Tile Size Notch Size Approx. Coverage per kg Up to 150 x 150 mm 4.5 mm ~0.7 m² 150 x 150 to 250 x 250 mm 6 to 8 mm ~0.5 m² 250 x 250 mm and over 10 to 12 mm ~0.3 m² Coverage varies with substrate condition, trowel angle and application technique. Drying and Grouting Typical set time is about 24 hours at 23°C and 50% relative humidity. Allow longer for dense tiles or cool and humid conditions. Grout after adhesive has set, usually after 24 hours. Movement Joints Provide joints around perimeters and at intervals consistent with good tiling practice, for example at about 5 m on floors and about 3.5 m along walls. Keep joints about 6 mm wide and free of adhesive and grout. Fill with a suitable flexible sealant. Limitations Not suitable over concrete where extended drying can occur. Not for areas subject to water immersion such as pools. Do not use for non-porous tiles over non-porous substrates or for moisture-sensitive stone. Final adhesive bed must be at least 1.5 mm and not more than 6 mm thick. Clean Up Clean tools and any fresh residue with water before the adhesive sets. Technical Data Type Single part viscous paste Colour Grey Bulk Density ~1.2 g/cm³ pH ~8.5 Slip 0 mm Extended Open Time ~1.2 MPa after 30 min Shear Bond Strength ~0.9 MPa Pack Sizes and Shelf Life Available in 1 kg, 4 kg, 10 kg and 20 kg pails Shelf life 12 months in unopened packaging stored in a dry place Good Practice Tips Use tile spacers for consistent joints and remove them before grouting. Prime porous substrates as directed for best results. Always follow movement joint requirements for long-term performance.
$59.48
Dunlop Primer & Additive is a water-based multipurpose solution that improves the bond between porous substrates and adhesives, waterproofing membranes, or screeds. It can be used as a primer before tiling or as an additive to strengthen screeds and grouts. Surface Preparation: Ensure the surface is clean, dry, and free of dust, oil, wax, paint, or other contaminants. For new concrete or screeds, allow to cure completely. Fill cracks and voids using a patching compound. Application Instructions: As a primer, dilute 1 part Dunlop Primer & Additive with 3 parts water. Apply evenly using a brush or roller. Allow it to dry for at least 30 minutes before applying adhesives or membranes. As an additive, replace part or all of the mixing water in tile adhesives or grouts to improve flexibility and adhesion. Follow the manufacturer's recommended ratios. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Allow to dry for at least 30 minutes before overcoating. Drying may vary depending on temperature and humidity. Clean Up: Clean tools and equipment with water immediately after use. Technical Data: Base: Water-based acrylic polymer pH: Neutral Appearance: Milky white liquid Shelf Life: 12 months (unopened in cool, dry conditions)
$64.80
Dunlop Multipurpose Floor Leveller is a high-flow, cement-based compound ideal for smoothing and levelling uneven internal concrete surfaces before applying tiles, vinyl, carpet, or other floor coverings. Designed for ease of use, it pours and spreads to form a smooth surface ready for foot traffic and covering in minimal time. It’s perfect for domestic and light commercial applications. Surface Preparation: Ensure the surface is sound, dry, and clean. Remove all traces of dust, grease, oil, curing compounds, wax, or any loose particles. New concrete must be fully cured. Mechanically remove surface laitance or contamination. Porous surfaces may require priming to reduce absorption and improve adhesion. Priming (if required): Apply a compatible primer using a broom or roller and allow it to dry before applying the leveller. On extremely porous substrates, a second coat may be necessary. Mixing Instructions: Slowly add the contents of the 5kg bag to approximately 1L of clean water while stirring with a mixing paddle. Mix for 2–3 minutes until a lump-free, smooth consistency is achieved. Do not retemper once the mixture begins to set. Application Instructions: Pour the mixed product onto the floor and spread using a steel trowel or smoothing blade. The product will self-level and settle to a smooth finish. Apply at a thickness of 1–10mm in one application. Protect from foot traffic until it is fully cured. Coverage: Covers approximately 3.5m² at 1mm thickness per 5kg bag. Coverage varies with substrate texture and thickness. Drying Time: Walkable: 4 hours Ready for tiling: 4–6 hours Ready for other coverings: 24 hours Dry times will vary depending on temperature, humidity, and layer thickness. Clean Up: Clean tools and mixing equipment with water immediately after use. Do not allow the product to dry on tools or surfaces. Technical Data: Type: Cement-based self-levelling compound Application Thickness: 1mm to 10mm Working Time: 15–20 minutes Walkable: After 4 hours Final Cure: Up to 24 hours Colour: Grey Shelf Life: 12 months if stored in original, sealed packaging
$40.20
High-Performance Ready-Mixed Ceramic Tile Adhesive This high-grab adhesive is designed to support even the heaviest wall tiles, providing superior flexibility for interior applications, particularly in kitchens and bathrooms. Key Features: Ready-mixed adhesive High grab for heavy wall tiles Superior flexibility Tile Types: Ceramic wall tiles Granite Marble (excluding moisture-sensitive stone) Suitable Surfaces: Cement render Fibre-cement sheets Painted surfaces (properly prepared) Plasterboard Application Areas: Indoor walls Coverage: 0.5m² per kg
$19.86
A water-based protective sealer which penetrates and cures within the pores of the grout. The sealer is fast drying and the bottle contains a brush for easy application. A water-based protective sealer Deep penetrating into the grout Easy to use brush for perfect sealing over grout Fast drying formula Coverage Seals up to 25m2 per 250ml
$20.03
Dunlop Floor Repairer Rapid Patch Mortar is a high-performance, fast-setting compound ideal for repairing holes, cracks, and uneven surfaces on internal floors. Suitable for use prior to the installation of tiles, vinyl, carpet, or other floor coverings, it delivers a smooth, level finish ready for light foot traffic within 45 minutes and covering applications in as little as 2 hours. Surface Preparation: Ensure the substrate is clean, sound, and free of grease, dust, oil, paint, or other contaminants. Surfaces should be dry and firm. Smooth or sealed surfaces must be roughened or etched. For porous substrates like timber, fibre-cement, or plasterboard, priming may be required. For floors in direct contact with soil, a moisture barrier should be used before applying the patch mortar. Mixing Instructions: Add 5kg of product into approximately 1.5L of clean water in a clean container. Mix thoroughly with a mixing paddle to a lump-free, smooth consistency. Mix only what can be used within 15 minutes. Application Instructions: Apply with a steel trowel to the required thickness (up to 20mm in a single application). Shape and smooth the surface before the material begins to set. For deeper repairs, additional layers can be applied once the initial layer has set. Avoid adding extra water once mixed. Coverage: Approximately 3m² at 1mm thickness per 5kg bag. Coverage varies with surface texture and thickness applied. Drying Time: Initial set: ~45 minutes Ready for coverings (tiles, vinyl, carpet): ~2 hours Final cure: 24 hours (depending on thickness and ambient conditions) Clean Up: Clean tools and equipment immediately with water before the mortar sets. Technical Data: Type: Rapid-setting cementitious repair mortar Application Thickness: Up to 20mm Pot Life: 15 minutes Foot Traffic: 45 minutes Ready for Coverings: 2 hours Colour: Grey Shelf Life: 12 months in original unopened packaging stored in a dry area
$39.52
Dunlop Express Wet Area Waterproofing Membrane is a high-performance, fast-drying liquid membrane designed for use in internal wet areas including bathrooms, showers, laundries, and kitchens. This flexible, water-based acrylic polyurethane formulation creates a seamless and highly durable waterproof barrier that is tile-ready within hours. It’s suitable for use under tile adhesives, screeds, and other flooring products. The product forms a tough, elastomeric layer that resists movement, cracking, and water penetration. It meets the requirements of Class III membranes and is suitable for both floor and wall applications. Surface Preparation: Ensure all surfaces are clean, dry, and structurally sound. Remove dust, grease, oil, curing compounds, and loose or flaking materials. Prime all surfaces using a compatible primer. On porous or highly absorbent surfaces, apply a second primer coat if needed. Any existing cracks, gaps, or joints should be sealed or reinforced using bond breakers or reinforcing fabric. Application Instructions: Apply the membrane using a brush or roller. Two coats are required for effective waterproofing. First coat should be applied in one direction. Once dry to the touch (approx. 2 hours), apply the second coat in the opposite direction. Membrane should extend at least 150mm up walls in general wet areas and 1.8m in shower recesses. Waterproofing must be applied continuously and without breaks or pinholes. Use reinforcing fabric over joints and corners if required. Avoid application in conditions below 10°C or above 35°C. Coverage: Approximately 1m² per litre per coat. A 5kg pail covers roughly 2.5m² with two coats, depending on surface porosity. Drying Time: Touch dry: 1–2 hours Recoat time: 2 hours Ready for tiling: 4–6 hours Fully cured: 24 hours Drying times will vary with ambient temperature and humidity. Clean Up: Clean tools and equipment immediately after use with water. Do not allow membrane to dry on tools. Technical Data: Type: Water-based acrylic polyurethane Classification: Class III membrane Application Method: Brush or roller Flexibility: High Water Resistance: Excellent Colour: Grey Shelf Life: 12 months (unopened in cool, dry conditions)
$80.40
Dunlop Damp-Proof Waterproofing is an acrylic brush-on membrane designed to prevent rising damp, efflorescence, and resist negative hydrostatic pressure. It adheres excellently to substrates including brick, masonry, concrete block, concrete, stone, and timber, and can be easily applied using a brush or roller. Once cured, it can be overcoated with most decorative paints. Surface Preparation: Ensure all surfaces are structurally sound and free from existing coatings, adhesives, and efflorescence to achieve maximum bond strength and resistance to hydrostatic pressure. Surfaces may be damp but not wet and must be cleaned free of dirt, grease, oil, or other contaminants. Fill holes and non-structural cracks with a suitable floor repairer before application. Application Instructions: For Floors: Spread the material using a brush or long nap roller to achieve coverage, then finish with a long nap roller. For Walls: Apply using a brush, roller, or spray, ensuring even coverage. Work the material into voids to avoid pinholing. For areas affected by hydrostatic pressure, apply a minimum of two coats. The second coat can be applied after 4 hours. Ensure uniform coverage and the required dry film thickness per coat. Coverage: Single Coat: Approximately 3m² per litre, per coat, when used as a barrier to efflorescence or as a moisture-resistant coating over green concrete. Multiple Coats: For areas with hydrostatic pressure, two coats are required at a coverage rate of 1.5m² per litre per coat. Additional coats may be necessary to achieve uniform coverage. Drying Time: Allow the membrane to cure for 24 hours before applying adhesives, mortars, decorative coatings, or other surface treatments. Ensure the membrane is not damaged during subsequent treatments. For floor surfaces, allow the final coating to cure for at least 24 hours before further treatment to minimize the risk of mechanical damage. Clean Up: Wash all equipment with water or a water/detergent mixture immediately after use. Technical Data: Base: Acrylic Application Temperature: 10°C to 35°C Dry Film Thickness: Achieve required thickness as per application guidelines Curing Time: 24 hours before overcoating Shelf Life: Refer to packaging for details
$144.00
The DTA Boss Grout Clean Up System Kit is a professional-grade cleaning solution designed to make post-grouting clean-up fast and effortless. Ideal for both tradespeople and DIYers, this all-in-one system helps you remove grout haze and residue from tiles after grouting. What’s Included: Heavy-duty cleaning sponge with handle High-capacity rinse bucket with roller Surface Preparation: Before use, ensure that the tiled surface has set appropriately based on grout manufacturer instructions. The grout should be partially cured but not fully hardened — typically 10–30 minutes after application. Remove excess grout with a rubber float before using this cleanup system. Application Instructions: Fill the rinse bucket with clean water up to the indicated level. Use the included sponge to gently clean the surface in a diagonal motion. Rinse sponge regularly by rolling it over the inbuilt rollers to remove grout particles. Repeat the process until the grout haze is removed and the tile surface is clean. Coverage: Cleans up to approximately 25–50m² per fill depending on tile texture and grout thickness. Drying Time: Tiles are generally clean and dry within 30–60 minutes of cleanup depending on ambient temperature and humidity. Ensure proper ventilation for best results. Clean-Up: Empty the bucket, rinse the sponge and components with clean water. Dry thoroughly before storing to extend product life. Technical Data: Rollers: Dual high-strength plastic rollers Sponge: Extra absorbent and replaceable This system is compatible with most grout types including cementitious and epoxy grouts. For stubborn epoxy residue, use in conjunction with a suitable epoxy grout cleaner.
$209.48
Davco® Tile & Grout Cleaner is specially formulated to tackle tough dirt and stains from tiles and grout. It’s also effective in removing minor efflorescence, making it a versatile cleaner for common tiled surfaces. Key Benefits: Specially formulated ingredients Effectively cleans tiles and grout Removes minor efflorescence from grout Helps remove mould and mildew from grout surfaces Usage: Davco® Tile & Grout Cleaner is suitable for a wide range of tiled surfaces, including: Ceramic Porcelain Mosaic Quarry Slate tiles It’s ideal for removing tough dirt and stains from tiles, as well as refreshing aged grout. Packaging: Size: 1 Litre Jerry Can Colour: Clear liquid Application Steps: Mixing: Dilute Davco® Tile & Grout Cleaner with water in a clean plastic bucket at a ratio of 10 parts water to 1 part cleaner (e.g., 5L of water to 500ml of cleaner). Application: Prepare the Surface: Always wet the surface with clean water using a mop or sponge before applying the product. For Normal Cleaning: Dampen a mop or sponge with the diluted solution and wipe over the surface, then immediately rinse with clean warm water. For Heavily Soiled Areas: Apply a larger quantity of the solution and allow it to soak for up to 10 minutes. Scrub the affected area with a stiff nylon brush, then rinse thoroughly with clean warm water. Keep your tiles and grout clean, refreshed, and free from tough stains and minor efflorescence with Davco® Tile & Grout Cleaner.
$33.54
Davco SMP Evo Tile Adhesive is a high-performance, flexible cement-based adhesive ideal for the installation of natural stone, porcelain, and marble tiles. Specially designed with advanced low-dust technology, it provides a cleaner and safer working environment. Its superior non-slump properties make it perfect for wall and floor tiling, including large-format tiles. Surface Preparation: Ensure surfaces are structurally sound, dry, and free from contaminants like dust, oil, and wax. Smooth surfaces should be roughened slightly, and absorbent substrates should be primed. Existing tiles must be clean, dry, and securely bonded. Mixing: Mix 5kg of powder with approximately 1.4–1.5L of clean water using a mechanical mixer until a smooth, lump-free paste is formed. Allow it to stand for 5 minutes before remixing. Do not add more water after mixing. Application: Apply the adhesive with a notched trowel over an area no larger than can be tiled within the open time. Firmly press tiles into the adhesive bed with a twisting motion to ensure full contact. Back-buttering may be necessary for large tiles or uneven substrates. Coverage: Approximately 1.5–1.75m² per 5kg bag using a 10mm notch trowel. Drying Time: Tiles can generally be grouted after 24 hours. Allow 2 days before exposure to water in wet areas and 21 days for submerged areas like pools. Clean-up: Clean tools and excess adhesive with water before it sets. Once cured, adhesive must be removed mechanically. Technical Data: Classification: C2S1TE Pot life: 1.5 hours Open time: 30 minutes Adjustability time: 20 minutes VOC content: Low Appearance: White powder
$30.14
Davco® Sanitized Glue Grout A Pre-mixed, Ready-to-Use Wall Tile Adhesive and Grout Davco® Sanitized Glue Grout is a flexible, white, pre-mixed adhesive and grout for internal wall tile applications. Ideal for thin bed fixing of porous-backed ceramic tiles, it’s suitable for domestic areas like bathrooms, kitchens, and laundries. Key Features: White appearance Pre-mixed and ready for immediate use Dual-purpose: serves as both adhesive and grout Ideal for fixing lifted or popped tiles No wastage Usage: Surfaces: Cement renders Rendered brickwork and blockwork Plasterboard Fibre-cement wall sheets Tiles: Suitable for thin-bed fixing of most porous-backed ceramic tiles Areas: Interior applications, including domestic walls, bathrooms, kitchens, and laundries Advantages: Ready to use, no mixing required Suitable for adhesive and grout in one product Convenient for quick repairs or installations No product wastage Packaging & Colour: Packaging: 500g pail Colour: White paste Application Information: Adjustability Time: 20-30 minutes (depending on climate and substrate porosity) Ready for Use: 24 hours Note: Drying time may vary based on climate, substrate, and tile porosity. Coverage: A 500ml tub of Davco® Sanitized Glue Grout covers approximately 0.5m² when applied with a 6mm notched trowel as an adhesive. Application Steps: Surface Preparation: Ensure all surfaces are structurally sound, dry, clean, and free of contaminants like oil, grease, or loose material. Deeply contaminated surfaces should be abraded to expose at least 80% of the original substrate. Follow these preparation guidelines: Substrate Specific Requirement Primer Rendered brick/blockwork Cured minimum 7 days, sound Davco PrimeX or Ultraprime Fibre-cement sheet/plasterboard Correctly and firmly fixed Davco PrimeX or Ultraprime Previously painted surfaces Sand back to expose 80% of surface Davco PrimeX or Ultraprime Mixing: No mixing required. Davco® Sanitized Glue Grout is ready to use straight from the pail.
$24.79
Davco PrimeX Multipurpose Acrylic Primer 5L is a professional-grade, water-based primer specially formulated to improve the adhesion of tile adhesives and waterproofing membranes to porous surfaces. Ideal for interior and exterior walls and floors in domestic and commercial applications, this primer ensures strong bonding performance while reducing porosity and dusting of substrates. Surface Preparation: Surfaces must be clean, dry, and free from dust, oil, grease, wax, paint, curing compounds, and other contaminants. Remove any laitance, loose materials, or previous coatings that may interfere with adhesion. On hot or windy days, dampen porous substrates lightly to avoid flash drying—but do not leave standing water. Application Instructions: Stir the primer thoroughly before use. Apply evenly using a roller, brush, broom, or squeegee in a thin, consistent layer. Allow the primer to dry fully before proceeding—drying is complete when the white, milky appearance turns clear. Coverage: Approximately 6–10m² per litre, depending on surface porosity. Drying Time: Typically dries within 30–60 minutes under standard conditions. Cooler temperatures or high humidity may extend drying time. Clean Up: Clean tools and equipment with water immediately after use. Do not allow the product to dry on tools. Technical Data: Type: Acrylic-based Colour: Milky white (dries clear) Suitable for: Cement render, concrete, fibre cement sheets VOC Content: Low Packaging: 5 Litre plastic container
$88.36
Davco Grey One Pot Premixed Tile Adhesive is a high-performance, ready-to-use acrylic-based adhesive, perfect for interior wall and floor tiling. Its premixed formula eliminates the need for onsite preparation, providing excellent adhesion and ease of application for both professionals and DIYers. Surface Preparation: Ensure all surfaces are sound, dry, and free from dust, oil, grease, or any other contaminants. Painted or glossy surfaces should be roughened and cleaned. For porous surfaces, priming may be required to ensure maximum adhesion. Application Instructions: Stir the adhesive thoroughly before use. Using a notched trowel, apply the adhesive to the substrate. Only spread as much adhesive as can be tiled within 20 minutes. Firmly press tiles into the adhesive, ensuring full coverage on the tile back. Adjust tiles within 20 minutes of placing them. Allow adhesive to set for 24 hours before grouting. Coverage: Approximately 0.75–1.25 m² per litre using a 6mm notched trowel. Coverage may vary depending on substrate and trowel size. Drying Time: Allow 24 hours before grouting. Full cure achieved within 7 days under normal conditions. Clean Up: Clean tools and excess adhesive with water immediately after use. Once dried, adhesive is more difficult to remove. Technical Data: Appearance: Grey paste Base: Acrylic Open Time: 20 minutes Adjustment Time: 20 minutes Application Temperature: 5°C to 35°C Ready for Grouting: After 24 hours
$30.24
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$12.44
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.70
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.72
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.33
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$12.44
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.02
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$5.81
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.83
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$18.48
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$15.65
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$8.50
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.91
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$7.93
Can I use Command™ Products on glass windows? It is okay to use Command™ Products if the glass is not exposed to direct sunlight and not flooded with water. For glass shower doors use our special Water-Resistant line of products (blue strip) which are clearly marked on our packaging. Will Command™ Products stick to brick? No. Command™ Products are intended for mostly smooth surfaces such as those listed above. However, our products will stick to painted, smooth cinder block (the type found inside many school and office buildings). Can I use Command™ Products on fresh paint? Paint should be fully cured (check paint can for manufacturer's cure time) before using Command Products. We recommend waiting 28 days before use on fresh paint. Also, alcohol may remove or dull the surface of fresh paint. Can I use Command™ Products on wallpaper? No. Most wallpapers are too delicate and can tear when adhesives are applied. Will it hold soundproofing acoustic foam board or decorative plates? Yes, provided the item is within the weight limit specified for Command™ Picture Hanging Strips. We do not recommend hanging tapestry or other fabrics. For decorative plates, please ensure there is a smooth surface for the strip to adhere to. Do not hang valuable or irreplaceable items.
$6.82
You have seen 768 out of 858 products
Reliable, tidy solutions for typical weekend tasks: mounting, gap filling, sealing, small timber or tile repairs and quick décor updates. Prioritise fast-set or instant-bond options to keep projects moving, and pick paintable/sandable finishes for a clean result. Use filters to refine by chemistry, cure profile and application method. Always review the product page and TDS/SDS for prep, working time and return-to-service guidelines.
