A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$8.00
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$11.05
A fast setting strong and durable two-part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features: Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance: Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product: General Use -Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. -All traces of grease, rust paint, etc. should be removed. -For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. -Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. Safety tips: Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$14.00
A fast setting strong and durable two part epoxy, general purpose adhesive. Mixed product gels in 5 minutes. Initial bonding is achieved in 20 minutes with maximum bond strength after 16 hours. Features Araldite is stronger than other glues due to the chemical reaction of the two parts Bonds a variety of surfaces Dries Clear Quick setting in 5 minutes No clamping necessary Moderate water resistance Forms a rigid, durable bond Can be used for gap filling (surfaces need not mate closely) Good chemical resistance Appearance Clear with a slight yellow tinge Where can this product be used? Bakelite – joining or repairing Bonding shells, stones or pebbles to decorate bottles, lamps, bricks or garden pots Repairing splits or cracks in a tennis racket Repairing metal toys Not suitable for bonding plastics such as Polypropylene and Polyethylene Bond strength weakens above 65°C but strength is regained when temperature drops What materials is this product suitable for? Glass Metal Wood Fabric Rigid Plastic Crystal Leather How to use this product General Use Before applying the Araldite mixture, all surfaces MUST be thoroughly clean and dry. All traces of grease, rust paint, etc. should be removed. For best results, smooth surfaces should be roughened by mechanical abrasion after solvent cleaning. Onto a clean, disposable surface (e.g. polyethylene or cardboard), dispense equal volumes of Part A and Part B. Thoroughly mix together with a spatula, nail or stick. When using the tubes it is essential to use the correct mixing ratio, i.e. 1 part each Apply adhesive immediately to both surfaces and press together. Clamping is not necessary, but allow bond to remain undisturbed for at least 20 minutes. Scrape off excess adhesive and wipe mixing utensils immediately. When using the Araldite 5ml Everyday tube, ensure correct caps are replaced on each tube or they will harden. To use Selleys Araldite Singles: Fold – the pack in half, so that foil is back to back. Tear – carefully along perforations. Squeeze – bubbles to extrude adhesive. Mix – two parts together until well combined. Apply – mixed adhesive to surfaces and bring together. Wipe off excess adhesive and do not apply undue strain to bond for 30 minutes. Handy tips For maximum working time, mix in small quantities. Large quantities accelerate the curing process and reduce working time. To extend product life replace caps immediately after use. Ensure you wipe excess from nozzle with a tissue dipped in acetone (or nail polish remover) before replacing the caps. When using the tube variant, ensure you replace the correct cap on the correct tube. Placing the wrong cap on the wrong tube will cause the tube to harden. (lids and tubes are colour coded to help) Wipe off any uncured araldite with acetone or nail polish remover. To remove product after cure, mechanical action (scraping or sanding) is recommended. Since the product is chemically resistant solvent will NOT dissolve this product. To reposition the bond once cured, check that the item is heat resistant. If safe, heat the item slowly, e.g. in an oven, to at least 150oC. The product will soften and liquify slightly. Scrape off any excess then reposition the joint carefully using appropriate safety equipment. Allow the item to cool down in the correct position. The product will reharden once returned to room temperature. Clamping is recommended for a stronger bond. Singles are great for those unexpected household breakages, so keep them at home, just in case. Keep a box of Selleys Sugar Soap Wipes around for quick & effective clean up. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would reccomend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with Methylated Spirits. If there is old difficult to remove residue such as oold paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Safety tips Avoid contact with the skin and eyes. Avoid breathing vapour. Do not use solvents near eyes or open wounds. In case of contact with eyes, flush with water for at least 15 minutes and seek medical attention. Non toxic when set. For further information refer to the Material Safety Data Sheet (MSDS). Storage and re-use Ensure caps are replaced and product stored in a cool dry place.
$18.00
PVA adhesive specially formulated for interior woodworking repairs and projects. White in colour, dries clear and cleans up easily with water. Features No mixing required – Ready to use straight from the pack Suitable for end grain gluing – won’t stain timber, white in colour, but dries clear. Non-toxic Dries Clear Cleans up with water Where can this product be used? School projects and craft Furniture repairs Repair a split trim Fix a broken photo frame Restoring furniture Fix a wobbly chair Gluing cupboard shelves for additional support Repairing a door frame or window Fix a wine rack Re-attach book cover/spine or repair torn bindings Fix a broken drawer Wooden toy repairs Craft projects Unsuitable for use on coated wallpaper overlaps eg vinyl Although Aquadhere is reasonably water resistant, it is not recommended for use in water or weather exposed situations or for any job where maximum water resistance is required (for weather exposed and/or wet areas we recommend Aquadhere exterior or Aquadhere Durabond). Will not take common timber stains Aquadhere is not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue. Do not use on projects that you need to be able to sand, as Aquadhere Interior is not sandable. Will not bond MDF, we recommend using Aquadhere Exterior What materials is this product suitable for? End grain gluing Craftwork Cloth Paper Mosaics Leather Other craft materials How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Cure slows significantly in humid, cold conditions. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Handy tips 1L covers approx. 8m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use Selleys 308 High Stress Wood Glue. Avoid contaminating Aquadhere with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond Cured adhesive can be resoftened by prolonged contact with hot water or steam. Sanding isn’t an effective way to prepare for gluing, as it often leaves an uneven surface and may clog the timber which can stop the glue from penetrating and impact on your result. A straight router can be used to trim the edge, but be sure to only remove as much as required to obtain a suitable edge for gluing. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of SELLEYS Sugar Soap Wipes nearby for a quick and effective cleanup. Safety tips Aquadhere is considered a non-hazardous material. In case of eye contact, hold eye open and flush with plenty of water for 15 minutes. Storage and re-use For maximum shelf life store inside at moderate temperatures. Do not allow to freeze.
$15.00
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$23.00
Industrial grade PVA, especially developed for use by professional woodworkers and craftsmen, for large projects. Off-white in colour, drying to a light coloured clear film. Features Excellent performance properties for repairs or building projects No mixing required Suitable for exterior use in non-structural applications Heat resistant to 110°C (bonds will not weaken in exposure to direct summer sun) Can be chiselled, routed or turned Suitable for end grain gluing – won’t stain timber, cream in colour, but dries clear with a slight yellow tint Non-toxic Sandable – will not clog sandpaper like other PVA emulsion glues More water resistant than Aquadhere interior Has a higher heat resistance than Aquadhere interior Paintable Provides a stronger bond than Aquadhere interior for larger jobs Bonds MDF Weather resistant Cleans up with water Where can this product be used? Cabinet and furniture making Timber letterbox Making a bookshelf Restoring furniture Gluing cupboard shelves for additional support Repairing a door frame or window Repairing or building wooden outdoor furniture Indoor furniture Storage chest for tools Pot plant stand Dog kennel Bed heads Timber joinery Wooden toys Unsuitable for use on coated wallpaper overlaps eg vinyl Will not take common timber stains Not recommended for joints that are subjected to constant high stress. Instead, use Selleys 308 High Stress wood glue Not suitable for below waterline applications or continuous submersion. We recommend Selleys Knead It Aqua for these situations. What materials is this product suitable for? Softwoods Plywood Joinery Hardwoods MDF Laminating Particleboard Dowelling Veneering Chipboard How to use this product Surfaces to be bonded must be close fitting, free from dust, dry and clean from grease. Shake bottle before use Apply adhesive liberally to one surface only, position surfaces and press together while still wet. Immediately clamp for 30 minutes for softwoods and 1 hour for hardwoods. Alternatively, low clamping pressures (50lbs/in2) can be used with softwoods; higher pressures are recommended for hardwoods (100 – 150lbs/in2). Do not stress joint for 12 hours. Wipe off excess adhesive while still wet with a damp cloth. If the wood is to be stained, any residual Aquadhere left on the timber surface may prevent the stain from taking to the wood. Maximum strength is achieved after 12 hours, but longer in cold, damp conditions, or when used on dense timbers. Clean all tools with water before adhesive is allowed to dry. If dry, soak in water until adhesive is soft. Cure slows significantly in humid, cold conditions. Handy tips 1L covers approx. 5m2 To fill small gaps, Aquadhere can be mixed with sawdust. Longer clamping times may be required for joints under high stress, or alternatively use 308 High Stress Wood Glue. Avoid contaminating Aquadhere Exterior with iron and steel, eg nails, etc. Aquadhere contaminated with rust (iron oxide) will stain brown/black in the presence of tannins in many woods. Painting or varnishing constructions made of porous softwoods will improve the resistance of bonds to water exposure. On very porous surfaces applying a thin layer to each side and allowing to soaking in before applying a second layer to one side only may result in a stronger bond. If you are gluing over a larger surface, try using a small roller to aid in application. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using Selleys Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as Selleys Kwik Strip Smart. Ensure the surface is dry before applying the product. Keep a canister of Selleys Hand Kleen Wipes nearby for a quick and effective cleanup.
$15.00
Durabond is moisture curing, high strength, polyurethane construction adhesive. It has high strength and water resistance making it excellent for jobs requiring extra durability, both interior and exterior.Durabond is sandable, paintable and stainable. It is suitable for bonding wood to almost anything. A superior adhesive, it is also excellent for bonding Features Super Durable High Strength 100% waterproof* – *(not for permanent water immersion) Bonds wood to almost anything Acid & chemical Resistant – PVA’s break down with acid/alkaline contact Versatile can be used to bond surfaces other than wood Heat resistant up to 140 deg Generous working time (10 minutes) Expands as it dries Sandable – easy, will not clog sandpaper like other PVA emulsion glues Paintable Stainable after sanding The product is a brown liquid and turns a light yellow when fully cured Can be used for gap filling Can Also be used to bond surfaces other than wood I.e metal to metal Bonds MDF Non-Toxic (once fully cured) Where can this product be used? Interior and exterior Sauna or cabinet repairs in high heat areas Bonding Timber to other surfaces (metal etc) Cubby House with metal roof & floor lining Planter boxes Steps leading off a verandah Timber letterbox to a metal support frame Window frame Decorative timber to a pergola Interior panels of a boat Repairing wooden boat oars Repairing wooden handles on tools Timber joinery Laminating chopping boards Requires atmospheric moisture to cure, therefore use may be restricted in dry conditions (refer to tips for advice) Cannot be used if application temperature is below 5°C For best results, one surface should be porous Not suitable for below waterline applications or continuous submersion, for this we recommend Knead-It Aqua Not recommended for structural applications Not recommended for vertical projects due to runny consistency While Aquadhere Durabond can adhere to damp surfaces excess moisture can result in increased foaming and a weakened joint. Ensure tight clamping or weighting to reduce foaming Surfaces should be clamped tightly or weighted What materials is this product suitable for? MDF Glass Metal Concrete Ceramic Most plastics (will not adhere to polyethylene or polypropylene, test other plastics first). All timbers How to use this product Surfaces to be bonded must be close fitting, clean, dust and grease free. Wipe very dry porous surfaces with a damp cloth 1 minute before bonding. Apply a thin layer of adhesive evenly to one surface only. Glue expands and foams as it cures. Assemble parts together within 10 minutes and clamp firmly or weight to hold until cured. Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container). Wipe away any excess adhesive immediately with acetone. After drying, any excess adhesive can only be removed by scraping, sanding, filing or cutting. Clean tools with acetone or white turpetine immediatly after use (before adhesive dries). Handy tips 1L covers approx. 8m2 It is advisable to wear gloves (adhesive bonds to skin and is extremely difficult to remove from skin). For bonding with smooth surface materials such as glass, plastics or metals, we suggested sanding or roughening the surface. The tighter you clamp, the better bond you will obtain (as Durabond expands). Wipe nozzle clean and seal container tightly. (to prevent remaining product from hardening in the container.) Wipe oily timber surfaces with acetone on a clean rag to remove any surface oils & allow to dry before applying adhesive. In extremely dry conditions or for extremely dry surfaces (eg terracotta) wipe surfaces with a damp rag prior to bonding to ensure sufficent moisture is present to cure product. Surfaces should not be wet. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer. For cleaning surfaces prior to application of adhesive, if the surface is porous, we would recommend using SELLEYS Liquid Sugar Soap. If the surface is non-porous eg glass or metal, firstly clean the surface with mineral turpentine and then again with methylated spirits. If there is old, difficult to remove residue such as old paint, we recommend using paint stripper such as SELLEYS Kwik Strip Smart. Ensure the surface is dry before applying the product. If glue comes in contact with hands, use acetone or white spirits to remove immediately and then rinse off with soapy water followed by hand creme. Alternatively wipe hands regularly while using Aquadhere Durabond. Once cured, adhesive is extremely difficult to remove from skin. If cured material is discovered on the skin, then rub vegetable oil or Vitamin E cream into the area repeatedly to accelerate the natural process of the skin shedding, which will in turn cause the cured product to fall off. Safety tips Contains organic isocyanate polymers. On contact, uncured adhesive can irritate eyes. If in eyes, flood the eyes for at least 15 minutes and seek medical advice. Avoid contact with skin, if contact occurs, remove contaminated clothing or flush skin and hair with running water. Avoid breathing vapours. Ensure use in a well-ventilated area. Product releases methyl ethyl ketoxime while curing. For advice, contact a Poisons Information Centre (AUS 131 126; NZ 0800 764 766) or a doctor. Warning: this product contains organic isocyanate polymers. This product has been classified as hazardous according to the criteria of NOHSC and HSNO. For further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site. Keep away from children. Storage and re-use Clean tools with acetone or white spirit immediately after use (before adhesive dried). Storage – For maximum shelf life store inside at moderate temperatures in dry conditions. Keep tightly closed to prevent moisture and air contact. It is recommended to use the entire contents of a pack within 6 months of opening. Product may form a hard skin on the surface during this period. Usable material is normally still present beneath this skin and can be accessed by breaking the hardened layer.materials other than wood.
$28.00
Selleys All Fix Multi Grip is a strong multipurpose adhesive that dries clear it is ideal for hobby projects or repair of household items and PVC pool liners. FeaturesMultipurposeDries Clear for a seamless bondStrongFlexibleSafe to use indoors and outsideSolvent based adhesive Where can this product be used?Hobby projectsRepairs of household itemsPVC pool liners What materials is this product suitable for?WoodMetalGlassCeramicBrickConcreteCorkMost plastics* How to use this productUse in a well ventilated areas. Ensure surfaces are clean and dry. Remove cap and carefully pierce foil seal with sharp object. Replace nozzle part of cap.Squeezing gently, apply an even coating of Selleys All Fix to both surfaces to be joined. Press surfaces together and clamp or hold firmly for approximately 1-2 minutes or until adhesive grabs. Instant bonds can be achieved on contact by waiting approximately 1 minute before pressing parts together firmly.Allow approximately 10-12 hours drying to achieve strength sufficient for normal use. Maximum bond strength is achieved after 24 hours or longer if large areas or nonporous materials (e.g. PVC) are being bonded.After application, clean nozzle and replace cap. Any spills can be removed with acetone (found in some nail polish removers). Clean UpUncured product may be removed with waterCured product can be removed by scraping Handy tipsFor very porous surfaces – apply a thin coat to both surfaces and allow to dry (approximately 5 minutes). Apply another layer as per normal directions. Limitations*Not suitable for polyethylene and polypropylene – use Selleys All Plastic FixNot suitable for polystyrene foam – use All Fix Big JobsNot for bonding requiring heat resistance above 90°C – use Quick Fix Ultra RepairSafety tipsDo not swallowAvoid contact with skin and eyes and breathing vapourRemove from skin with soap and waterIf in eyes, hold eyes open, flush with plenty of water for 15 minutes and seek medical attentionHighly flammable, keep away from sources of ignitionFor advice, contact a Poisons Information Centre (AUS 131126; NZ 0800 764766) or a doctorFor further detail on the safe use of this product, please refer to the Material Safety Data Sheet, which can be downloaded from this site Storage and re-useLeave nozzle on tightly if storing once opened
$9.51
Selleys All Fix Big Jobs is a convenient all-rounder adhesive that sticks just about anything to anything. It provides virtually instant grab on dry porous surfaces eliminating the need for nails and screws on many jobs. It is a heavy-duty adhesive that will bond a wide variety of materials, has low fumes, and conveniently cleans up with water. Features Fast - virtually instant grab on dry porous surfaces eliminates the need for nails and screws on many jobs Fast grab minimises the need for clamping Strong - Heavy-duty adhesive that will bond a wide variety of materials Safe - Low odour, low fumes and non-flammable Dries white and is able to be painted over once dry Lots of working time - bonds can be repositioned within 5-10 minutes Easy to use Fills minor gaps in uneven surfaces (bridges gaps up to 9mm) Strong bond on porous surfaces after 24 hours, cures to maximum strength over a few days Where can this product be used? Re-adhering carpet House numbers to brickwork Wooden furniture repairs Repairing damaged plasterboard Building a dog house Skirting boards Attaching architraves Attaching wall panelling Attaching chair (dado) rails Attaching or building a shelf Use for larger interior projects What materials is this product suitable for? Plasterboard Cabinet Plaster coving Carpet Wood Particleboard Metals (other surface must be porous) Glass (other surface must be porous) Ceramics (other surface must be porous) Brick (other surface must be porous) Concrete Cork Polystyrene foam (other surface must be porous) UPVC (other surface must be porous) Many rigid plastics* (other surface must be porous) Loose wall tiles (in non-wet areas) How to Use Surfaces to be bonded must be dry, sound and free from grease/oil and dust. Work tube between fingers for several seconds to loosen contents. Cut the tip of the nozzle and squeeze to apply adhesive onto one surface. Immediately press parts firmly together. Bonds can be repositioned for up to 5 minutes. If adhesive surfaces form a skin no bond will form. The bond will usually have good strength after 24 hours and will continue to strengthen for a few days. Application Tips For long narrow attachments (e.g. skirting boards) apply one or two continuous beads. For larger flat areas use beads approximately 30cm apart. For small items (e.g. tiles) spots of adhesive may be used. Wipe away excess adhesive with a damp cloth. Dried adhesive is best removed by scraping. Limitations: Not suitable for permanently wet or damp areas. Not suitable for fixing mirrors. Use Selleys Liquid Nails Mirror Metal & Glass. *Not suitable for polyethylene and polypropylene. Use Selleys All Plastic Fix. Bonds are not water-resistant. Protect bonds from water penetration if used in exterior applications. Not resistant to strong acids and strong organic solvents. Do not apply below 10°C. When used near brass or copper, the immediate area of contact will discolour to a blue tone. Handy Tips At least one surface must be porous for effective bonding. If both surfaces are non-porous, drying time is greatly increased. Clamping may be necessary until adhesive dries. Wet, damp and cold weather will increase drying time Wipe away excess with a damp rag. Use temporary supports when bonding a heavy load - support until adhesive dries. Particularly on uneven or smooth or non-porous surfaces. Good for gap filling - i.e. sticking two rough surfaces together. All Fix Big Jobs may stain slightly and colour can be paler than the surrounding area, squeeze out should be wiped off if intending to stain. Clean Up Uncured product may be removed with water. Cured product can be removed by scraping.
$14.81
Invisible Hold - Virtually clear design lets your décor take center stage Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lb use 60" Designed For: Glass, Tile, Acrylic and Metal For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch-Mount™ Clear Double-Sided Mounting Tape. Virtually clear, this double-sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer because of its 3M™ industrial strength adhesive. So whether you're mounting acrylic cosmetic organizers or a translucent picture frame, affix it confidently with Scotch-Mount™ Clear Double-Sided Mounting Tape. Invisible Hold - Virtually clear design lets your décor take center stage Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lb use 60" Designed For: Glass, Tile, Acrylic and Metal Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in Brazil Color: Clear
$38.06
Invisible Hold - Virtually clear design lets your décor take center stage Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lb use 60" Designed For: Glass, Tile, Acrylic and Metal For items that need an undetectable mounting means, reach for the stealth adhering power of Scotch-Mount™ Clear Double-Sided Mounting Tape. Virtually clear, this double-sided permanent tape is perfect for mounting glass, tiles and artwork. Its strong bond holds up to 15 pounds, without the hassle of nails or a hammer because of its 3M™ industrial strength adhesive. So whether you're mounting acrylic cosmetic organizers or a translucent picture frame, affix it confidently with Scotch-Mount™ Clear Double-Sided Mounting Tape. Invisible Hold - Virtually clear design lets your décor take center stage Intended for indoor use - Delivers a strong, permanent bond on contact Holds up to 15 lb with 3M™ industrial strength adhesive To hold 1 lb use 4" To hold 15 lb use 60" Designed For: Glass, Tile, Acrylic and Metal Application temperature 50°F to 100°F Easy-to-apply design with no mess or tools Use instead of nails and screws Ensure your surface is smooth, clean and dry for the best bond Great for do-it-yourself projects Made in Brazil Color: Clear
$13.12
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
3M™ Marine Adhesive Sealant 5200 is extremely strong and retains its strength above or below water line. Stays flexible too - allows for structural movement. Has excellent resistance to weathering and salt water. Stress caused by shock, vibration, swelling or shrinking is effectively absorbed. Check the bonding and sealing jobs this product can handle for you: fibreglass deck to fibreglass hull, wood to fibreglass, portholes and deck fittings, motors on fibreglass transoms, under mouldings, hull seams above and below water line. Centre board trunk joints. Between struts and planking. Stern joints. Deck housing, etc. Easy to apply with manual caulking gun. Won't sag or flow in vertical or horizontal seams. Very high strength Watertight bonds Above/Below waterline use Specifications Adhesive Type Polyurethane Application Method Hand or pressure caulk Brand 3M™ Colour White Consumer Label Yes Cure Time 24 Hours Full Cure 3mm per 5 day Hardness 68 Shore A Industries Marine Physical Form Medium paste Product Form Cartridge Solids Weight Percent (Approximate) 97 Percent Tack Free Time 12 Hour
$55.00
![3M Claw Drywall Picture Hanger 65lbs 30Kg [Pack x 2]](http://gluesaustralia.com.au/cdn/shop/files/638060921234_e9940663-65b0-41b5-a196-e209139e4251.jpg?v=1754712826&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25, 45 & 65 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$19.49
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 3]](http://gluesaustralia.com.au/cdn/shop/files/638060661598_a9209f0c-7031-48ec-be4f-9fb1e87b6730.jpg?v=1754712828&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$23.94
![3M Claw Drywall Picture Hanger 45lbs 20Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661581_a0340f7e-ce42-40cb-b71a-cd5b0abb2b66.png?v=1754712829&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$8.76
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 4]](http://gluesaustralia.com.au/cdn/shop/files/638060661574_fb2086bb-b8e6-4490-8e91-ea0a14fda213.jpg?v=1754712831&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$21.66
![3M Claw Drywall Picture Hanger 25lbs 11Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661567_47226083-6c1f-44e5-9a7f-4238c8ab3fcf.jpg?v=1754712832&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$9.51
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 5]](http://gluesaustralia.com.au/cdn/shop/files/638060661550_1fe37b78-c060-4f27-8387-63c1e448c0e6.jpg?v=1754712834&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$21.66
![3M Claw Drywall Picture Hanger 15lbs 7Kg [Pack x 1]](http://gluesaustralia.com.au/cdn/shop/files/638060661543_46481795-b414-41bc-a9c1-dc9b380c967f.jpg?v=1754712835&width=645)
Introducing the new 3M CLAW™ Drywall Picture Hanger! Trust your heavyweight hanging projects to the 3M CLAW™ Drywall Picture Hanger proven to hold up to 15, 25 and 45 pounds. The engineered hardened steel claws lock securely into drywall anywhere – just push, hang and you’re done. HARDENED STEEL - Claws lock into drywall anywhere. PROVEN HOLD - Trusted strength up to 45 pounds NO TOOLS – just push in with your thumbs NO STUDS – Hang anywhere on drywall NO REGRETS – No big holes left in your walls NO MEASURING - Includes 1 Spot Marker to mark where the mirror or art piece will hang before installing the hanger AWARD WINNING - Popular Science: “Best of What’s New” Award. Best New Product Award for Picture Hanging Category in a 2021 BrandSpark® survey. Product of the Year Winner: Home Improvement Category. Survey of 40,000 people by Kantar.
$8.94
Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Specifications Application Dent Fill Brand Bondo® Color White, Off white Product Type Glaze Putty Substrate Aluminum, eCoat or Paint, Galvanized, SMC Details Quickly bonds to primer, metal, fiberglass and aluminum Two-part component formula delivers excellent durability and less shrinkage Quickly repairs paint scratches, minor dents and stone chips Good spreading properties allow for ease of use Fast curing makes putty sandable in only 20 minutes Putty is compatible with all types of automotive paint systems Use during the Fill stage of the 3M™ Body Repair System Bondo® Professional Glazing & Spot Putty smooths and repairs pin holes, scratches, nicks, minor dents, stone chips and other surface imperfections in automotive paint and bodies. This product is a 2-part component formula that securely and quickly bonds to primer, metal, fiberglass and aluminum. Professional Quality Surface Blemish Repairs Bondo® Professional Glazing & Spot Putty quickly repairs paint scratches, minor dents and stone chips. Our professional quality formula comes as a two-part product with putty and cream hardener to produce a mixture that won't shrink once cured. This glazing and spot putty has a 5-minute working time and a 20-minute curing time, giving you the perfect balance of enough time to complete the repair with a fast cure that keeps your project moving forward on schedule. Perfect Repairs Every Time Once cured, you're ready to sand to create a smooth patch that matches the surrounding surface beautifully. Our repair putty securely bonds to primer, metal, fiberglass and aluminum, and it resists gumming up sandpaper and shrinking. It can be used with all types of paint systems for professional-looking results. Use During the Fill Stage of the 3M™ Body Repair System Even a small repair can seem complex at first. So 3M's Body Repair System simplifies the entire automotive body repair process by dividing it into four stages: Stage 1 — Prepare. This stage includes pulling dents, removal of paint and rust and efficient, effective masking of the area. Stage 2 — Fill. This stage involves patching holes with reinforced filler and smoothing and shaping filler before painting. Stage 3 — Paint. This stage includes painting the area and blending and smoothing primer and paint. Stage 4 — Finish. The final stage for showroom-grade results: removing small defects, sealing and polishing clear coats and other painted surfaces. 3M supplies premium products such as abrasives, tapes, body fillers and tools for every stage. This system helps you work easily, efficiently and successfully across the entire body repair process.
$75.00
You have seen 694 out of 694 products
Reliable, tidy solutions for typical weekend tasks: mounting, gap filling, sealing, small timber or tile repairs and quick décor updates. Prioritise fast-set or instant-bond options to keep projects moving, and pick paintable/sandable finishes for a clean result. Use filters to refine by chemistry, cure profile and application method. Always review the product page and TDS/SDS for prep, working time and return-to-service guidelines.
